Search Documents

By R. K. Mishra, A. Kula, X. Jia, M. Niewczas

The mechanical properties of Mg-Gd and Mg-Y solid solutions have been studied under uniaxial tension and compression between 4K and 298K. The results reveal that Mg-Gd alloys exhibit higher strength and ductility under tension and compression attributed to the more effective solid solution strengthening effect and grain boundary strengthening. Profuse twinning has been observed under compression, resulting in a material texture with strong dominance of basal component parallel to compression axis. Under tension, twining is less active and the texture evolution is affected mostly by slip. The alloys exhibit pronounced yield stress asymmetry and significantly different work-hardening behaviour under tension and compression. Increasing of Gd and/or Y concentration leads to the reduction of the tension-compression asymmetry due to the weakening of the recrystallization texture and more balanced twinning and slip activity during plastic deformation. The results suggest that under compression of Mg-Y alloys slip is more active than twinning in comparison to Mg-Gd alloys.

Jan 1, 2015

The Daly-Judge Tunnel, begun in 1887 to drain mine workings, is now a source of potable water for the Municipality of Park City. The water is exceptionally clean; however, when roof falls occur, suspended solids levels become too high and water from the tunnel cannot be used in the treatment plant. In 2001, the tunnel was inspected and rehabilitated to ensure that the water supply for the 2002 Winter Olympic Games would be uninterrupted. Twenty-five timber tunnel sets were removed, and 86 steel sets were installed. Timber lagging was installed or replaced over about 230 m (750 ft) of tunnel length.

Jan 1, 2006

By B. L. Moreau

Certain gas wells tend to form hydrates in the production tubing. This paper outlines a method developed and used by the Author's company to overcome the problem. The injection of glycol to control hydrates results in sufficient dehydration to allow the gas to be trans-ported through a field-gathering system b a treatment plant. Sub-surface injection of glycol also offers a method of introducing corrosion inhibitors into the gas stream. The major operating difficulties have been overcome and the system is now in use in the northeastern part of British Columbia.

Jan 1, 1958

By A. G. Storey, J. B. W. Bailey

"The Noranda Process at the Horne Division ofNoranda Mines Limited now smelts approximately 350,000 short dry tons of concentrate a year, which is 40% of the total smelter throughput. Campaigns are averaging 200 days and refractory consumption is much lower than in the conventional smelter.In this paper, details ofrecent operation are given, together with updated projections for operation with higher levels of oxygen enrichment.IntroductionThe Noranda continuous smelting process has been in operation at Noranda, Quebec, for six years and in that time it has smelted a million and a half tons of concentrate. It is currently smelting 1,200 to 1,250 tons per day of concentrate on an instantaneous basis"" and it is handling approximately 40% of the Horne smelter throughput.This paper will describe the current operation of the process and the improvements that have been made since 1976, when the process was described by L.A. Mills et al.lSince early in 1975, a high-grade matte averaging 73% copper has been produced, which is then sent to the converter aisle for final treatment. All the information in this paper refers to the operation of the process in the matte mode .Early in 1978, Kennecott Copper Corporation started up their new smelter near Salt Lake City, Utah , which has three Noranda Process reactors operating with high oxygen enrichment of the tuyere air (2). These furnace s incorporate some design improvements, which will be described briefly."

Jan 1, 1980

By Steven Doyle

Presentation Outline ?Introduction to Brunswick Mine ?Mining Needs and Drilling Trends ?Maintenance Program ?Back to Basics ?Results ?Additional benefits Introduction Xstrata Zinc Brunswick Mine ?No. 12 deposit discovered in 1953, pilot mining 1957, u/g mining began in 1964 ?Zinc, copper, lead and bulk lead/zinc concentrates ?Since 2007, a fully owned division of Xstrata Zinc Canada ?Over 132Mt milled 3.4 % Pb, 8.8 % Zn and 102 g/t Ag ?Deposit dips approximately 70 degrees; strike length of 1200 m; currently mining from 250 m to 1125 m depth

Nov 1, 2011

By R. D. Hossack

"The selection of a site for plant facilities is a function of several factors and has as its objective the maximization of profits, given fixed markets and sources of raw material locations. In practice there are several sites, any one of which or a combination of two or more would be suitable to meet the basic requirements of source of supply of raw material and labour and still fulfill market demands. The model used to select the optimum profit combination utilizes both computer programs and traditional financial analysis techniques. Of the three computer programs used in the mode), one is a linear program and another is a transportation simulator. Basic cost and price data are required. In examining costs, three levels are used: (a) distribution costs of raw material to the plant and finished goods to the market; (b) direct production costs at the plant, such as labour and locally supplied material; and (c) capital and overhead costs at the plant, such as construction costs, taxes, insurance, and federal and provincial cost allowances. The direct costs generally depend on the scale of operations, so that a large plant in one location may have a lower unit cost than two smaller plants. This, of course, must be balanced against distribution costs. In examining profit, it is necessary to think in terms of the price and volume of sales at each of the market locations. Given basic data and relationships, the model can be used to optimally locate production facilities or, alter-natively, optimally structure a transportation network given existing locations of plants and markets. It is dynamic to the extent that it can react to changes in volume, price and cost to optimally locate an additional plant, the expansion of existing plants, the shutting down or cutting back of plants, or the restructuring of distribution networks."

Jan 1, 1970

By M. T. Ho, D. E. Wiley

The iron and steel industry accounts for almost 5 % of the total world CO2 emissions. Optimisation of the steelmaking process has led to significant reductions in the energy intensity to the point where it is now close to the thermodynamic limit. Further reductions are not likely to be achieved with efficiency improvement alone and will require the development of novel or breakthrough technologies. This paper will show the costs of implementing CO2 capture at direct atmospheric emission points for a number of iron and steel production processes. These include a conventional process, top gas recycling processes, the Corex and Hismelt smelt reduction processes and the Midrex direct reduction process. Depending on the point source emission, costs of capture with existing chemical absorption technology at iron and steel plants can be similar to capturing CO2 at pulverised coal fired power plants.

Jan 1, 2015

By Z. Ren, M. Tomlinson, E. Asselin

"Organic carbon blinding is a common, yet often partial, solution to the reduction of preg-robbing. A quantitative method to assess the extent of adsorption of a given blinding agent is presented herein. The adsorption of several blinding reagents on various carbon samples is quantified using electrochemical impedance spectroscopy (EIS). EIS results showed that kerosene is more strongly adsorbed on carbon than sodium lauryl sulphate (SLS), while SLS can hinder the charge transfer process of the oxygen reduction reaction on the carbon surface more effectively. The effectiveness of SLS is pronounced when its concentration is higher than 100 ppm. Raman spectra are presented for selected carbon samples: as the area ratio of the disordered peak to the graphitic peak increases, blinding agent adsorption increases.INTRODUCTION The presence of naturally occurring constituents in gold ores may adversely affect the extraction of gold in cyanide leaching since the gold cyanide complex, Au(CN)2–, can be adsorbed by these constituents (M. Adams & Fleming, 1989; Afenya, 1991; Miller, Wan, & Díaz, 2005). Such ores are known as “preg-robbing”. Preg-robbing behavior may arise from natural carbonaceous materials in the ore (M. Adams & Burger, 1998). In the past decades, a number of pre-treating methods have been developed for refractory carbonaceous ores (Arriagada & Osseo-Asare, 1984; Beer, 1994; Dunne et al., 2007; Jiang, Liu, Xiao, & Yang, 2012; Kohr, 1997; Kulpa & Brierley, 1993; Menne, 1992; Menne & Revy, 1994; Moyes & Houllis, 2010; Petrie, Craw, & Ryan, 2005; Simmons, 1996). The method known as blinding is one of the most effective and economical pre-treatment methods (M. D. Adams & Burger, 1998; Albert, 1923; Darrow, 1924; McQuiston & Shoemaker, 1975; Van den Berg, 2000). Blinding, also referred to as blanking or passivation, uses a chemical reagent to passivate the preg-robbing carbon by selective absorption or wetting (Bas, Altinkaya, Yazici, & Deveci, 2012; Brierley & Kulpa Jr, 1993; Dunne et al., 2012; Van den Berg, 2000; Yang, Qian, Song, & Dong, 2013; Yen, Amankwah, & Choi, 2008; Zhou, Jiang, & Choi, 2014). Organic reagents, which selectively adsorb on the surfaces of activated carbon and “smother” the surface, have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Two comprehensive studies by Abotsi and Osseo-Asare and Adams and Burger have been published on this topic (Abotsi & Osseo-Asare, 1986; M. D. Adams & Burger, 1998)."

Jan 1, 2017

By J. Sliwinski, H. Kikutani, J. Atwood, D. Larimer, J. Pyecha

"The Pogo mine start-up milling targets of 2005 are vastly different than the targets of today. Improvements have been driven by unintentional design oversight, continual circuit optimization or optimization due to changing mineralogy. The more significant process improvements to date have occurred in the gravity, flotation and leach/CIP unit operations. Details of the significant improvements are presented along with the impacts to the process.INTRODUCTION Deposit Overview Pogo mine is located along the Goodpaster River, southeast of Fairbanks, Alaska. This deposit sits in the center of the Tintina Gold Province (Figure 1), a region of similar Intrusion Related Gold deposits in Interior Alaska, the Yukon and British Columbia Canada (McCoy et al., 1997). The Pogo deposit is hosted in a rock sequence of amphibolite-grade gneisses intruded by mid-Cretaceous granitic plutons and dikes, which in turn, were cut by and host the auriferous quartz veins of the Pogo deposit.The Pogo deposit is comprised of three distinct zones of auriferous quartz veins spatially adjacent to each other. These are the Liese Zone, North Zone, and the East Deep Zone. The Liese Zone consists of three stacked, massive quartz veins, designated the L1, L2, and L3. Vein thickness averages 3.0 m, with variations from 0.3–18 m thick. The North Zone mineralization is comprised of four veins with more consistent thickness, between 1 and 1.5 m. The East Deep deposit lies northeast of the Liese Zone ore body. It is separated by a post mineralization, quartz diorite pluton. The East Deep Zone is comprised of two stacked massive quartz veins with similar orientation as the Liese Zone."

Jan 1, 2017

By J. K. Shaw

The science of low temperature engineering is well entrenched in mining. Uses for common cryogens, including liquid oxygen (LOX), liquid nitrogen (LN2), and liquefied natural gas (LNG) in the gas and minerals industries are reviewed. Potential future applications are discussed within the scope of mining, particularly in refrigeration and ventilation. The second part of this paper focuses on the Linde cycle, which is at the heart of most liquefaction plants. Steady state equations describing the mass and energy flows are presented. The paper concludes by explaining the concept of a wind powered Linde- Hampson cryogenic cycle and assessing, with scoping calculations, the technological feasibility of producing cryogens with an intermittent source of (renewable) energy.

Aug 1, 2013

By Ramsey Hart

MiningWatch Canada is the only national independent civil society organization with an exclusive focus on mining in Canada and Canadian mining companies operations internationally. In 2005, MiningWatch Canada collaborated with other NGOs to develop the Framework for Responsible Mining: A Guide to Evolving Standards. The project was the result of a perceived need by NGOs and retailers, particularly from the jewellery sector, for a framework that would set out environmental, social, and governance standards for the minerals sector ?providing recommendations for retailers and others seeking to source or invest responsibly, as well as regulate and encourage responsible mining practices?. This paper is a reflection on the Framework that examines key areas of concern and notes where the industry norms and expectations of civil society have evolved. The paper focuses on developments in social issues related to the UN Guiding Principles on Business and Human Rights, new initiatives associated with financial transparency, the UN Declaration on the Rights of Indigenous Peoples. The environmental components of the Framework that are revisited are waste management, biodiversity, energy and climate change, environmental assessment, mine closure, mercury and seabed mining.

Aug 1, 2013

By W. E. Hale

An area of about 7,000 square miles within the eastern part of the Grenville Sub-province is underlain chiefly by granitic gneisses. There are, however, some exposures of mafic rocks which warrant further investigation, and some attractive structures, particularly basins, which deserve additional economic consideration. T HIS paper describes in a very general fashion the economic and geological features of an area of about 7,000 square miles on the north shore of the Gulf of St. Lawrence in the eastern part of the Grenville Sub-province (Figure 1). The scarcity of published geological data on this part of the Cana-dian Shield (DePuyjalon, 1899 and Longley, 1944) justifies the presentation of these tentative results. It should be appreciated, however, that the information which follows was acquired in a rapid reconnaissance designed specifically to out-line what might be interpreted as favourable geological environments for the occurrence of economic minerals, rather than to produce an authoritative analysis of the geological history of the region.

Jan 1, 1962

By Y. Thibault, L. Morin, R. Cameron, D. Gould

"There are an estimated 50 to 100 million dry metric tonnes of low-grade nickeliferous pyrrhotite tailings in the Sudbury area alone, with an average nickel grade ~0.8% (plus cobalt). Pyrrhotite is a highly reactive sulphide mineral that has the potential to generate acidity; consequently, it is stored in large tailings ponds that require perpetual treatment to avoid the production of acidic drainage. Re-processing this material using bioleaching technologies has the potential to recover valuable metals, while reducing the toxicity, reactivity, and acid generating potential of the remaining residues. CanmetMINING is currently developing a stirred-tank bioleaching process to recovery nickel and cobalt from pyrrhotite-rich tailings. Stirred-tank experiments have been conducted with one tailings sample over a range of pH and temperature conditions, resulting in 80 to 90% and 70 to 80% leaching of nickel and cobalt respectively in 10 days.INTRODUCTION Sulphide tailings may represent a significant financial liability for mining companies as these wastes may produce acidic drainage under some disposal conditions. As a result, the companies must post financial bonds large enough to ensure there are sufficient funds for perpetual management of these wastes. At the same time, there are billions of dollars in metals incorporated into these mining wastes waiting to become valorized. Many sulphide tailings are amendable to bacterial oxidation for metal extraction. Re-processing of tailings using bacterial leaching has the potential to recover valuable metals from waste; and reduce the toxicity, the reactivity, and the acid generating potential of the remaining residue. By reprocessing these wastes there is an opportunity to significantly reduce liabilities and financial assurance bonds, while recovering metal values. There are an estimated 50 to 100 million dry metric tonnes of low-grade nickeliferous pyrrhotite-rich tailings in the Sudbury area alone with an average nickel grade ~0.8% (Peek et al., 2011) plus cobalt and copper. Pyrrhotite is separated from pentlandite concentrates by magnetic separation and flotation. It is already finely ground and has often been segregated from other tailings material, making „mining? relatively inexpensive. This represents roughly (> $100/ton) in contained value, with negligible mining costs. This paper reports on the development of a stirred-tank bioleaching process for recovering nickel and cobalt from pyrrhoitite-rich tailings, which is currently underway at Canmet MINING."

Jan 1, 2017

By W. H. Gross

To pollute means to make impure or unclean. We tend to forget that man defecates, urinates, sweats, expectorates and exhales and in himself is a beastly little pollutor-but then so is Mother Nature! The object of this paper is to try to put what man and nature do into perspective. The facts indicate that although man may sweat a little, Ms. Nature is by for the greatest pollutor of all.

Jan 1, 1979

By H. W. Wevers

This paper is the result of an intensive literature search and practical study of the problems experienced by a mining company with the frame cracking of their large-tonnage haulage trucks. It explains the advantages of particular HSLA steels for applications in the welded structures of such equipment. Examples of existing welds in truck frames are analyzed. Modern fatigue models and linear elastic fracture mechanics techniques are explained.

Jan 1, 1978

By Tom Gaines, G. S. Brant, J. G. Debanne

"AbstractThe Bonnie Glen oil field, one of Canada's largest, lies about fifty miles southwest of Edmonton, Alberta. One hundred and thirty-eight wells have been completed in this field since its discovery in January, 1952. Five different procedures have been used in completing the producing wells.The reservoir is an Upper Devonian biohermal reef with good porosity and uniformly high permeability. The top of the reef is quite flat but the flanks slope at angles approaching 20 degrees from the horizontal. The reservoir has a gas cap with a maximum thickness of 400 feet, an oil column of 300 feet, and a :porcus aquifer of over 300 feet. The reservoir pressure is now 2,400 pounds per square inch gauge at datum ( -4100 M.S.L.).Because of the high permeability and the high •pressure, lost circulation and resultant blowouts are a particular hazard in drilling at Bonnie :Glen field. To reduce the dangers of blowouts, it is general practice to run casing to the top of the reef. If the reef is encountered 'high' it was usual practice to run a liner and perforate for completion. Wells penetrating the •reef below the gas/oil interface were either completed in open hole or through casing perforated opposite the oil pay, with the former method more frequently used. Eight wells were completed by the Humble-Otis permanent-type completion, and recently five high wells were completed open hole with the gas •cap exposed. This latter completion, 'tubing submergence', has proved highly satisfactory thus far.The open-hole type of completion is cheaper than the liner perforation method and results in better well performance. More experimentation and data are needed before the tubing submergence method can be recommended unqualifiedly. but all evidence thus far favours its use in reef reservoirs."

Jan 1, 1955

By A. Navarra, C. Arrancibia, R. Yañez, C. Acuña, F. Valenzuela

"Discrete event simulation (DES) is a suitable framework to evaluate and optimize the dynamics of sulphide smelters. In particular, iron-nickel-copper-cobalt sulphides undergo continual oxidation within a roasting or smelting operation, followed by batch oxidation within the converting operation, thus producing iron-free Bessemer matte (or blister copper, in the case of copper smelters); this semi-finished product undergoes further processing to produce nickel, copper and cobalt products, and to recover precious metals. The juncture between continuous smelting and batch converting is often an appropriate focus for the earliest phases of DES development, since it is typically a major bottleneck within nickel and copper smelters; later phases may include increasing levels of detail for auxiliary unit operations, as well as plant logistics. Moreover, DES can support matte-slag chemistry, including Gibbs free energy balances to determine the iron speciation within the slag. DES is therefore capable of linking the fundamentals of oxidation reactions to the intricacies of plant dynamics.INTRODUCTION Discrete event simulation (DES) is gaining acceptance within the extractive metallurgy community, as a technique that quantifies the system-wide performance of metallurgical plants under conditions of uncertainty (Wheeler & McGinty, 2015). In particular, over 90% of smelters that process nickel-copper-cobalt sulphides and copper sulphides exhibit similar semi-continuous dynamics (Crundwell et al., 2011b; Schlesinger et al., 2011b), in which the converting aisle produces batches of material that are sent for further processing (Figure 1). Thus the tools and practices that are developed for a specific sulphide smelter are often relevant to numerous other smelters.The juncture between continuous smelting and batch converting has long been a focus for discrete event simulation (Welgama et al., 1996). Nonetheless, the broad acceptance of DES in nonferrous smelters has been hindered by interdisciplinary barriers that divide industrial and metallurgical engineers (Navarra et al., 2016; Noorossana et al., 2012); this divide has been less severe in steel plants (Hollocks, 2006). In recent years, DES has been used in copper smelters to analyze crane-and-ladle motions (Coursol et al., 2009a), reverts production and consumption (Noorossana et al., 2012), and innovative control systems (Herrera et al., 2016); additionally, DES models have accounted for shutdowns and random breakdowns to provide realistic assessments of copper smelter capacities, thus guiding equipment upgrades (Campbell et al., 2013; Coursol et al., 2009a). All of these studies feature a Peirce-Smith converting aisle similar to Figure 1 that, under normal operations, constrain the smelter throughput, and are thus a bottleneck (Campbell et al., 2013; Navarra et al., 2016)."

Jan 1, 2017

By D. Komljenovic, E. Lafontaine, J. Paraszczak

Availability of the production equipment used in underground mines has a substantial impact on production costs and, thus, on mine profitability. Appropriate collection of pertinent data and information, as well as use of adequate performance measures and their analyses, can help mine operators identify cost-effective opportunities to improve equipment availability. This paper presents study results aimed at reviewing and analyzing means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews sources, as well as quality and quantity of relevant data and information, and examines performance measures and their definitions, as applied to surveyed mines. Problems concerning data acquisition and meaningfulness of the performance measures are discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. Evidence suggests that the latter may become a more useful tool for mine operators in their efforts to reduce production cost.

Jan 1, 2008

By D. L. Thompson

Foreword The complete history and early development of the Sullivan mine was fully covered in a paper entitled 'The Development of the Sullivan Mine and Processes for the Treatment of its Ores', prepared by the staff of the Consolidated Mining and Smelting Company of Canada, and presented at the Annual Meeting of the British Columbia Division of the Institute at Trail in October, 1924. At a subsequent meeting at Blairmore, Mr. E. G. Montgomery read a paper on the mine, and in 1926 Mr. M. M. O'Brien brought the subject up to date at the joint meeting of the American and Canadian Institutes at Cranbrook. The present paper is necessarily based largely on these earlier accounts. Discovery and Early Development The outcrop was discovered in 1892 and the property was bonded and later sold to the Sullivan Group Mining Company, of Spokane. From 1896 to 1899, surface stripping and test pits (at A) around the outcrop exposed a vien of sulphides with varying amounts of lead and zinc. In some places, a 35 per cent lead ore carrying 15 ounces of silver was found. These lenses were of commercial value. With the completion of the Kimberley branch of the Canadian Pacific railway, in 1900, some systematic development was started. A shaft l00 feet in depth was sunk (at B). Shaft-house, boiler-room, and compressor-plant were erected, and a steam diamond-drill was put into operation.

Jan 1, 1929

By N. Shi, T. G. Joseph

ABSTRACT: An interactive cable shovel simulation has been developed to mimic any shovel dipper geometry for a given cable shovel operating in any homogeneous face material. This interactive cable allows the user to predict shovel performance in any face material encountered and track both its ground stability and the dipper-ground interaction. An embedded Microsoft® Visual Basic spreadsheet was used as the platform for developing an interactive simulation that allows for maximum user-defined parameter input and interactive visual output. The result is an analytical dipper-ground interaction solution that yields crowd, hoist, and digging effort as a function of face activity position.

Jan 1, 2011