Search Documents

By C. J. Van Treeck

PGE concentrations of 18 g/t occur in the pyroxene rich rocks at the Union Bay Alaskantype complex. This PGE enrichment is hosted in magnetite veins. These veins cross magmatic layering and have an irregular morphology in both outcrop and thin section. Fe-Ti oxide geothermometry suggests that this mineralization took place between ~700-400°C. A variation in the amount of ilmenite and Mg- Al spinel exsolution in magnetite correlates with temperature estimates, lower temperature magnetite has less exsolution. Hydrous silicates form an alteration envelope around magnetite veins with a formation temperature of <575oC, vary with temperature, and contain appreciable amounts of Cl. Interaction of a PGE-Fe-Cl rich fluid with clinopyroxene increased the fluids pH and decreased PGE and Fe solubility depositing a PGE enriched magnetite within the Pyroxenites and Olivine Pyroxenites of the Union Bay complex.

May 1, 2003

By CIMVAL

This Code for the Valuation of Mineral Properties (the “CIMVAL Code”) is the result of a review more than a decade after the release in 2003 of the “Standards and Guidelines for Valuation of Mineral Properties” (the "2003 Standards"). The purpose of the review is to update the 2003 Standards to reflect domestic valuation, international valuation, and regulatory developments. The CIMVAL Code was adopted by the Canadian Institute of Mining, Metallurgy & Petroleum (the "CIM") Council on November 29, 2019. The CIMVAL Code supersedes the 2003 Standards. The 2003 Standards were dated February 2003 and were adopted by the CIM Council on March 9, 2003 as the first comprehensive set of standards for Valuation of Mineral Properties in the Canadian mining industry. The 2003 Standards followed recommendations of the Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission, where in its Final Report (January 1999), the CIM was specifically asked to form a committee of valuation practitioners to review and advise on standards for the Valuation of Mineral Properties. The Special Committee on Valuation of Mineral Properties ("CIMVAL") was created on May 5, 1999 with the mandate to recommend standards and guidelines for Valuation of Mineral Properties to be used by the mining industry in general. The CIMVAL Code is limited to the Valuation of Mineral Properties (including any interests therein) and does not cover valuation of corporations or other entities that hold Mineral Properties as assets. The CIMVAL Code does not cover petroleum and related assets. CIMVAL recommends that the CIMVAL Code be followed for all Valuations of Mineral Properties, including those required by securities administrators and stock exchanges. However, when a Valuation is required under the applicable rules of securities administrators or stock exchanges, such rules prevail to the extent of any inconsistency.

Nov 29, 2019

By A. McLean, M. Barati

In this paper, examples are presented of pyrometallurgical research and associated teaching activities during the past century within the Department of Metallurgical Engineering, now the Department of Materials Science and Engineering, at the University of Toronto. Throughout these years, pyrometallurgical research has been characterized by recognition of the importance of the interdependence of measurements and models as well as the development and application of sensors, for the generation, validation and practical implementation of new knowledge. The important role played in the delivery of lectures and participation in joint research by Adjunct Professors with strong backgrounds in the pyrometallurgical industry is described. Projects conducted in close collaboration with the industrial sector and opportunities for students to obtain practical experience working as teams on a "round-the clock" shift basis within an industrial pilot plant environment are outlined. These activities, together with the involvement of students in poster competitions and the presentation of papers at society conferences and technical meetings, are still vital elements in the development of pyrometallurgists equipped with the appropriate professional skills for subsequent employment within academia, government laboratories or the industrial sector.

Jan 1, 2015

By T. Iwasaki

This paper points out two key elements in resource trade in general and the Canada-Japan relationship in particular. The first is that the advanced countries have a more important role than one would expect in the supply of resources in world trade. Canada &apos;s dual role as a major resource supplier in conjunction with an advanced economy will continue to increase. The second point is the heavy reliance on foreign resource supplies in some advanced economies, particularly in Japan. Finally, as regard the future of the Canada-Japan economic relationship, particularly .in resource development, it is suggested that trade could be enhanced by an accelerated exchange of various types of resources between the two countries. These include natural resource commodities as well as the more abstract capital, technological and human resources.

Jan 1, 1978

By J. A. H. Church

The report is too voluminous to be considered in detail within the scope of a single paper, so I will confine my consideration of it to the broader aspects, leaving other members to deal with points of particular interest. The method of presentation leaves one with an uneasy sense of prolixity and confusion of thought; the foreword by the Chairman may well be accepted as a true index of the whole. His argument amounts to this: Recognizing at the outset the futility of divided counsels, it was deemed advisable to arrive at unanimity. To this end, some members subscribed to views to which they do not whole-heartedly assent, thus giving weight to conclusions with which they were at variance. Unanimity cannot be qualified-either it exists or is absent-and, moreover, in the text of the Com-mission I can find no word that unanimity is required. Surely it would have been preferable to have a unanimous report covering such aspects as were acceptable to all members, with minority reports by individual members on such other aspects as were controversial, leaving it to the Government to give such weight to the divergent views as the personality of their sponsors might warrant. In the final analysis the value of an opinion varies directly as the personality of its exponent.

Jan 1, 1926

By Zhen Lei

In Alberta, Canada, heavy industrial projects are constructed using a prefabrication approach: spools and pipes are produced in the factory, and are assembled into modules that are transported to the industrial plants for installation by mobile cranes. Planning the onsite mobile crane operations is critical to the project budget and schedule. However, due to the large magnitude of industrial projects, manual heavy lift planning is tedious, and the results are not particularly responsive to site changes. This paper introduces an integrated mobile crane management system developed by PCL Industrial Management Inc., in collaboration with the University of Alberta, which investigates crane location selection and path checking for field module assembly. The project information is stored in a database, and the proposed system retrieves data, performs the calculations, and records the results back to the database; the calculations involve automatically selecting locations for the mobile crane, considering the crane capacity, lifting range and utilization. Lift paths for modules are checked for feasibility based on selected locations, satisfying the site and crane configuration constraints, and crane walking paths are planned if needed. The designed system is tested in an industrial project to validate the effectiveness of the system.

Aug 1, 2013

By Brad McBain

Agenda ? Accurassay Laboratories and Automation ? History and experience ? Features and benefits of automation in the lab ? Tata Steel Minerals Canada (TSMC) Iron Ore Laboratory ? State-of-the art systems and design ? The integration of fusion systems and XRF units ? Meeting deliverables: quality, reliability, safety

Aug 1, 2013

By K. E. Barnes

"The “Jameson Cell” flotation cell was developed at Mount Isa Mines in the late 1980’s to address deficiencies in our flotation column installations. Early base metal installations had a variable record. The test work and trials showed they made an improvement metallurgically when operated correctly, but performance of the early installations was hindered by a range of operational and maintenance issues. The installations needed to be more robust, and we needed a better understanding of how to successfully integrate the cells into the plant flow sheet.During the 1990’s, Jameson Cells had great success in coal fines flotation and organic removal in SXEW applications, and became the standard in these applications in Australia. These installations improved the cell design and materials of construction and the cell flow sheet design, to make it low wear with self-regulating control, producing good performance with little operator input.These improvements have enabled a fresh look at the use of Jameson Cells in base metals. Recent new installations have shown significant benefits in “hybrid” circuits, that combine the best features of both Jameson Cells and conventional flotation cells, achieving better overall circuit performance in a smaller footprint than either technology could do by itself.Case studies of successful base metal applications are discussed, using size-by-size mineralogical performance to explain the improved circuit performance. The new methods of flow sheet test work design are also described."

Jan 1, 2006

By Paul R. Terry

This paper presents a brief picture of the quality of coal produced in Eastern Canada for use in thermal generating stations. It describes, in particular, the characteristics of coals burned in six power plants -two in New Brunswick and four in Nova Scotia. Each station is dis-cussed in turn, and comments are made on the coals used therein with regards to origin and physical and chemical properties affecting station operation. A table of coal data shows, at a glance, the wide variation in the quality of coals received by these stations from producers in New Brunswick and Nova Scotia. "The promotion of improved coal quality for thermal generation can benefit our national economy." T HIS is the opening statement in a paper which was presented by Mr. D. A. Pirttinen at the Coal Division&apos;s Toronto meeting in April, 1960. In bringing the power engineer&apos;s viewpoint to the coal producers&apos; attention, Mr. Pirttinen made a survey of utility steam plants operating in Canada, and the results of this survey formed the basis for his paper, which he titled: "Generating Station Coal Quality.

Jan 1, 1965

By C. Díaz, M. Barati

Prof. Torstein Utigard&apos;s untimely death, in the spring of 2012, put an abrupt end to a meritorious career in the field of high temperature chemical process metallurgy. As an academic in the Department of Materials Science and Engineering of the University of Toronto, Torstein made solid contributions to the advancement of knowledge pertaining to production and refining of both nonferrous and light metals, and to the development of inquisitive and innovative young people in extractive metallurgy. In this profile, the authors highlight aspects of Torstein&apos;s rich personality and of his contributions to his field of expertise.

Jan 1, 2015

By K. M. Tompson, R. L. Armstrong, C. I. Godwin

"Tungsten skarn deposits on the Clea property in the Selwyn Mountains, Y. T., are related genetically to a quartz monzonite stock, about 500 metres in diameter at the surface. Lower Paleozoic sedimentary rocks are metamorphosed for a distance of 3 km from the stock. Tungsten-bearing skarn mineralization within the altered sedimentary rocks is of two types: sulphide-rich pods and calc-silicate beds. The most significant scheelite concentration is in calc-silicate beds near or adjacent to the quartz monzonite stock. Discordant K-Ar and Rb-Sr isotopic dates indicate that the stock is probably of early Late Cretaceous age, 94 Ma or slightly older, and that it cooled slowly. High initial 87Srl86Sr ratios and disequilibrium relationships between K-jeldspar phenocrysts and groundmass minerals in the porphyritic phase of the granitic rock , and between different granitic rock specimens, indicate contamination of crystallizing magma by old sialic continental crust which extends westward under the Selwyn Basin.This study is significant to regional tungsten exploration. Granitic rocks associated with tungsten deposits, in this part of the Canadian Cordillera at least, appear to have specific isotope characteristics that indicate they were generated at a specific time and in a particular way.IntroductionThe Clea tungsten skarn property (Fig. I) is owned by Canex Placer Limited, and lies in the Selwyn Mountains (Bostock, 1948) near the eastern margin of the Selwyn Basin (Wheeler and Gabrielse, 1972), Yukon Territory. The property covers a 20-square-mile area centered near latitude 62°47 &apos; north and longitude 129°52&apos; west, and is accessible by helicopter. An airstrip and the terminus of a summer-use gravel road at MacMillan Pass, Yukon, are about 20 miles to the northnorthwest.This paper deals mainly with the geochronemetry of granitic rocks from a stock associated with tungsten mineralization on the Clea property. We show that these rocks have specific characteristics that not only define the genesis of this stock, but also have significance for regional tungsten exploration around plutons in the Canadian Cordillera."

Jan 1, 1980

By T. A. Rickard

FROM AN OLD MANUSCRIPT THE text for this contribution to the history of the Patio process is a page taken from a Spanish manuscript of Bartholomé Arzaj Sanches y Uela, now in the possession of the library of Brown University (see Figure 1). I owe the photographic print to the courtesy of the librarian. The date, as will be seen, is 1577. The subject is the treatment of silver ores at Potosi, in old Peru, but in modern Bolivia. The group of drawings (see Figure 1) is entitled "Arrangement of the machines in which the ores of silver are ground on the bank of Potosi, the one of two batteries and the other of one". First, top-left, we have the sketch of a "machine of one battery" operated by a water-wheel. From this mill the water runs in part along an aqueduct supported by pillars to the two-battery mill and in part down the hillside, where men are at work with "tubs, which are called cochas, in which are washed the charges of ore and amalgam". Along the top of the page are shown the "various offices in which are stored the copper, the salt, the ucha [llama dung, used for fuel], the lime, and other materials for the re-duction of the ores". To the right of these are "apartments and warehouses in which is stored the ore brought down from the mountain"?the cerro de Potosi. Through the arched portal come the "sheep [llamas] on which is brought down the ore". To this is added a reference to "the second gate, which closes the whole works". On the level above the aqueduct are seen six men carrying skin-bags that contain water. This is being sprinkled on the ore. On the extreme right are six more of these water-carriers. Next comes the two-battery mill. The mortero, or mortar, is marked on the right. Another description says, "Stone, on which the stamps crush the ore, which is called a mortar". To the left of these are indicated "screens of wire in which the ore is sifted after it has been crushed". Farther to the left, near the ore-washers, is a "shed, in which is placed the metallurgist to test the ore of the boxes". Along the left side of the page are sundry buildings, one of which is labelled a "shed in which are placed the cones of silver". Near it, lower, to the right, is the "furnace, in which are roasted the sulphides to facilitate treatment". Farther to the right is the "place where the Indians mix the charges of sulphide ore, which is called a buitron". Alongside is a "buitron in which the charges are prepared for reduction". Inside is a container, to which are attached the words "measure, called topo" On the extreme right is "another buitron in which the Indians mix the ores with their feet, as well as the heaps for the preparation of the reduction". Near the bottom, on the extreme left, is the "chapel where the holy sacri¬fice of the mass is celebrated". Under the first buitron is the "place where they dry the moist ores, called pãpear".

Jan 1, 1935

By Thomas. L. O.

Apart from a few sketches and incomplete maps, mainly topographical, and one or two detailed maps of placer-creeks, there is little information on the topography and geology of most of the country adjacent to the sections of the Alaska Highway in the Liard River area, particularly that part east of Kechika river. In 1943, the Geological Survey of Canada made a recon-naissance from Fort Nelson clown the river of that name to the Liard, thence up the latter to Hell Gate, and also up Beaver river for a distance of fifty miles. The whole of the area covered was found to be underlain by sedimentary rocks, not a single igneous dyke being seen. The British Columbia Department of Mines began reconnaissances near the highway both in and north of the drainage basin of Prophet and Muskwa rivers with a view to finding structures favourable for the accumulation of oil. In Liard River valley near the mouth of Smith river and at intervals from there clown to Devil&apos; s Portage occur warm springs whose character and origin are not definitely&apos; known, since they have not been investigated (21, p. 38A). Similar springs are said to occur at several localities over a broad belt extending from Muskwa river across the Liard to the Nahanni River country (26, p. 11). On Liard river below the mouth of Dease river, stratified sands, gravels, and clays of Pleistocene (?) age are constantly met with and in one or two places are underlain by sandy clays. The distribution of the latter, however, is very limited in the section cut by the river west of the Rocky mountains. The only range of these mountains that reaches the Liard is the high limestone ridge which approaches the mouth of Vents river from the southeast and then almost vanishes a few miles to the northwest of it (27, pp. 43-45). In general, the ranges of the Rockies in the area under consideration have been but little explored, but they are undoubtedly very largely sedimentary and, with the exception of some volcanics and intrusives on their western flanks, are probably almost entirely so. Unlike the high, deeply incised ranges in southern British Columbia, they dwindle in elevation north of Terminus mountain to low-wooded ridges separated by wide swampy valleys, and practically lose their identity between it and the Liard. The foothills, which, along the Liard, have a width of 38 miles (from near the mouth of Trout river to Hell Gate) are composed of a great series of alternating shales and sandstones, with some limestones, all folded closely together, which resemble those found in the foothills farther south (27, pp. 50, 19-20).

Jan 1, 1944

By G. Herget

"A brief visit to European longwall mining operations in potash showed that retreating longwall mining provides a very attractive alternative to room-and pillar mining, especially in areas with bad roof, narrow seams and areas with high ground pressures. Mines de Potasse d&apos;Alsace, France converted all potash operations to longwall mining in 1980. Recovery rates per panel vary between 75o/~ to 85% which compares very favourably with Saskatchewan values. Ground pressure in Saskatchewan are comparable to those of some of the deposits in Europe, but the presence of water in the hanging wall of Saskatchewan orebodies has to be given serious consideration. However, given the mining experience in Saskatchewan and the improved technology f or laboratory and field investigations, a review of present mining practice in Saskatchewan is desirable. IntroductionLongwall mining is practiced widely in coal mining and allows complete mechanization. It is applicable at great mining depth, in thin seams, weak roof and has been applied recently even to coal bed s dipping more than 65 degrees. Ideally this system allows complete extraction of an orebody. However, with high mechanization and emphasis on obtaining high outputs per man shift, extraction ratios rarely reach more than 80010 per panel.France, Spain and the U.S.S.R. have had longwall operations in potash for some time and a brief description is given below. Two of the operations were visited and the Russian operation is described based on German literature"

Jan 1, 1986

The Mineral Industry of Canada in 1951 Continuance of the remarkable, successive increases in the value -of Canada&apos;s mineral production, chief basis of the nation&apos;s post-war expansion, was one of the highlights of Canadian development in 1951, when, according to the preliminary estimate is-sued by the Dominion Bureau of Statistics and reported in the BULLETIN for February, 1952, mineral output for the year reached a new high of $1,228 millions. This marked an increase of 17.5 percent over the previous year, which was the first in which the billion dollar mark had been reached, and an increase of 143.7 per cent over 1946, when production was valued at approximately $503 millions. While higher prices for the principal base metals accounted for a large part of the 1951 increase, quantity gains were made by copper, nickel, zinc, asbestos. lead, cement, and strikingly important. by petroleum, the value of which exceeded for the first time that of coal production. Gold was an exception to the general trend, being lower in both quantity and value than in 1950. For the first time nickel .came within $9 millions of surpassing-gold as the leading mineral product. Metals and Fuels The value of all metals, estimated at $733 millions, was 18.7 per cent more than in the previous year. Nickel advanced 11 per cent in volume and 34 per cent in value. Copper was up 2.4 per cent in quantity and 21 per cent in value, zinc rose 6.6 per cent in quantity and 35 per cent in value, and although the volume of lead produced was lower by 8 per cent, its value increased by 17 per cent. The tonnage of iron ore was 31 per cent higher than in 1950.

Jan 1, 1952

By G. W. Adams

Foreword While the literature on radium is voluminous, there is no single publication available from Canadian sources which attempts to cover at all fully the world radium industry. The comparatively recent developments in the Wilberforce area, and the consequent arousal of public interest in radium, seemed to call for the publication of such a paper which would be intelligible to the layman. To satisfy this apparent need, the writers submit this paper which contains material derived from various sources, and for which the writers make no claim of originality. Direct references are made throughout the paper to sources of information.

Jan 1, 1931

By T. Holmes, S. Davison

"A surge bin at Agrium’s Vanscoy potash operations has been plagued with flow, wear, and corrosion issues since being built in 1967. The culprits? The bin’s carbon-steel construction, geometry, and the resultant funnel-flow pattern are the root causes. An investigation and cost analysis indicated that hopper redesign and retrofit would increase production and reduce maintenance and capital costs. The retrofitted bin provides safer, more reliable operation and has a much longer predicted working life. Using this example, the authors describe bulk-solids-flow theory and highlight the importance of customizing bulk-material-handling-system design using appropriate flow properties to improve reliability, safety, and cost effectiveness.RÉSUMÉ Depuis sa construction en 1967, un réservoir intermédiaire de l’exploitation de potasse Vanscoy d’Agrium connaît des problèmes de débit, d’usure et de corrosion. Les responsables ? La construction en acier ordinaire du réservoir, sa géométrie et la structure de débit en résultant au niveau de la carotte en sont les causes fondamentales. Une étude et une analyse des coûts indiquaient que la restructuration et la rénovation de la trémie permettraient d’augmenter la production et de réduire les coûts d’entretien et en capital. Un réservoir rénové permet de renforcer la sécurité ainsi que la fiabilité de l’exploitation, et sa durée d’activité prévue en est augmentée. En se fondant sur cet exemple, les auteurs de l’article décrivent la théorie du débit de matières solides en vrac et insistent sur l’importance de personnaliser la conception du système de manutention des matériaux en vrac à l’aide de propriétés rhéologiques adaptées afin d’améliorer la fiabilité, la sûreté et la rentabilité.INTRODUCTIONIn early 2013, Agrium’s Vanscoy Potash Operations (VPO) engaged Jenike & Johanson Ltd. (J&J) to provide testing, consulting, and structural engineering services related to proposed modifications to the 270 t special standard product surge bin, which Agrium planned to undertake during a two-week shutdown in August 2013. The bin, which had been plagued with flow, wear, and corrosion issues for its entire working life, was essential for the continuous operation of two of VPO’s compaction plants and for efficient dispatching to loadout. The bin often experienced product hang-ups, clumping on the walls, and plugging at the hopper outlet. Two recent unscheduled mill shutdowns had been partially attributed to flow issues in the bin due to clumping and product plugging up at the screws. These problems increased maintenance costs, limited production capacity, and degraded product quality. Holes and paper-thin sections in the bin walls discovered during a 2013 inspection revealed the potential for major hot material leaks or even structural failure. Either issue would stop plant operations until the bin could be repaired or bypassed. Clearly, the bin cone had reached the end of its life and required replacement."

Jan 1, 2018

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By G. Archibald, M. McSaveney, J. Wartman, M. Yetton, C. Massey, C. Holden, A. Kaiser

"The 2010/11 Canterbury earthquakes triggered many mass movements in the Port Hills including rockfalls, rock and debris avalanches, slides and slumps and associated cliff-top cracking. The most abundant mass movements with the highest risk to people and buildings were rockfalls and rock/debris avalanches. Over 100 residential homes were impacted by landslides, leading to the evacuation of several hundred residents.Volumes of rock leaving several of the larger cliffs during the earthquake sequence were determined from terrestrial laser scan change models. There were no seismically instrumented cliff sites and there was some distance between the cliffs and nearest strong-motion sites. Therefore, we synthesised free-field rock-outcrop seismograms by employing a stochastic approach controlled by source models and regional parameters derived using spectral inversion of the extensive strong motion data set. Relationships between volumes leaving cliffs during the earthquakes and site peak ground acceleration (PGA), peak ground velocity (PGV) and Arias intensity were compared for different sites. Multiple linear regression was used to analyse the variables that best predict the volumes of debris that fell from the slopes during the main earthquakes. The best correlation between the volume of debris falling per square metre of slope face and the seismic forcing parameters was for vertical PGV. The results from the multiple linear regression incorporating slope height, inclination, PGV horizontal and PGV vertical, improved the statistical relationship.Field data and results from the 2D seismic site response assessment indicate that the following factors affect dynamic performance of the modelled cliffs: 1) cliff geology—mainly material modulus, shear strength and shear wave velocity; 2) slope geometry—ridge-scale versus site-scale effects; and 3) the temporal aspects of the earthquake shaking (i.e., single acceleration peaks of large amplitude versus multiple peaks of smaller amplitude). Model results show that amplification of shaking does not increase linearly with increasing height, but instead reflects changes in the cliff geology where material strength, modulus and shear-wave velocity contrasts lead to acceleration contrasts.These factors show that the use of well documented case histories provide the basis for more certainty in seismic landslide assessments compared to those that are only empirically based."

Jan 1, 2015

By E. T. Turner

Introduction 1n assembling material for this paper on Wood Refuse Burning 1 turned first to the records of our early studies of the problem in order to learn how and why certain basic decisions were arrived at and also how it came about that the completed central steam plant differed so much from the original plans. It may be of interest, therefore, to outline the engineering problems as they presented themselves in the early part of 1948, and to indicate the economies involved. Although the principle of using wood refuse as boiler fuel instead of burning it to waste was quite sound, and in fact the practice had been in use for a long time in the boilers of many lumber companies, there was some guesswork as far as Hollinger was concerned in deciding how best to handle the large quantities of wood refuse involved and as to the type of boiler equipment necessary to .burn it efficiently. These problems will be examined first. Hollinger Boiler Equipment in 1948 Hollinger had four separate boiler houses, at Main, No. II, and No. 19 shafts, and a small unit at the compressor plant for heating purposes. Main and No. Il boiler houses operated all the year round; No. 19 and the compressor plant only in the winter. At Main there were four 36-year-old HRT boilers with total available h.p. of 500, at No. II, three 30-year-old HRT boilers with 195 available h.p., and at No. 19 two old field-type locomotive boilers capable of producing 95 h.p.

Jan 1, 1951