Search Documents

By R. Ramírez, N. Aslin, G. Ríos, T. Bravo, A. R. Almansa

Lacy copper has been an on-going concern at Atlantic Copper for at least 10 years and was first reported to Glencore Technology in mid-2010. Over the past 12 years, many of the plates were replaced due to age and general deterioration however; plate passivation and lacy copper issues have persisted. After analyzing all the possible causes of this phenomena, it was found that the problem is caused by a degradation of stainless steel as a consequence of the deposition of Sb oxides. These deposits act as passivating agents of stainless steel, which reduces the density of copper nuclei, causing defective copper deposit, with low thickness and ductility. After doing several tests for reducing/removing the phenomena, the over-riding factor was found to be the anode-cathode overlap. An adequate overlap eliminates the problem of "lacy copper". This was verified during an eight month trial with anodes extended 2.5cm in length. Longer anode not only avoids the appearance of lacy copper, but also recovers cathodes that already have lacy copper. On the other hand polishing of plates only gives rise to a temporary solution that requires on-going polishing, to avoid the re-appearance of lacy copper. INTRODUCTION The electrolytic copper refinery of Atlantic Copper in Huelva (Spain) was commissioned in 1970 with an initial capacity of 40,000 t of cathodes per year. In 1975 the copper refinery was expanded to 108,000 t/year. From 1994 to 1996, a new expansion together with the implementation of ISA permanent cathode technology led to a capacity of 215,000 t/y. Since 1995, a progressive increase in the current density up to 350 A/m2 has been accomplished, which together with an increase in the number of cells from 1,120 to 1,204, has led to the present cathode production capacity of 290,000 t/y A lack of copper deposition in the lower part of the steel permanent cathodes was first reported in 2010. This phenomenon is known as “Lacy copper” because of the appearance of the copper deposit as it can be seen in Figure 1. The occurrence of this phenomena was relatively low and was assumed to be originated by an excessive anode scrapping. Nevertheless, in December 2015 Lacy Copper was observed in a significant amount of copper cathodes giving rise to the following issues: Increased tramp copper – housekeeping and maintenance problems Poor appearance of cathode deposit and untidy looking bundles

Jan 1, 2019

By L. S. Beck

"The Athabasca region forms part of the Churchill province of the Canadian Shield and is underlain by an Archean or Aphebian assemblage of rocks that underwent severe metamorphism and granitization during the Hudsonian orogeny (1750-1950 m.y. ago). In places, the eroded orogen is overlain by unmetamorphosed cover rocks (in-cluding the Martin and Athabasca formations) of probable Paleohelikian age. Basic dykes cut all the rocks of the region.There are innumerable vein-type pitchblende deposits and many syngenetic occurrences of uraninite in crystalline basement rocks. Evidence is presented to show that pitch-blende was emplaced during the final stages of the Hud-sonian granitization and followed the crystallization of syngenetic uraninite transitionally. In terms of P-T condi-tions, the pitchblende deposits belong essentially to Lindgren's mesothermal group.Based on the postulated uranium metallogenesis, the possibilities of finding further deposits of pitchblende and other types of uranium deposits are discussed."

Jan 1, 1970

By D. R. Spink

An historical background is presented to provide a basis for the lack of normally expected developmental effort over the first 20-25 years of viable zirconium production operations. This is followed by a description of developing technology, which is the result of years of research and piloting effort directed to the development of a more economical method to produce high-grade metallic zirconium. It is predicted that many of the process improvements described will have a significant impact on future zirconium production methods and consequently on future prices and markets.

Jan 1, 1977

By S. Shairp

"After cooling and thickening, slurry from the second stage of the Hudbay zinc pressure leach circuit is filtered and washed on a belt filter prior to disposal. At times, the belt filter can be a bottleneck to the process. Preliminary studies show that filterability of the second-stage (HAL) autoclave leach residue can be indicated by particle size distribution of the filter feed and filtered residue cake. In particular, the Volume Weighted Mean Diameter, D[4,3], generated by a laser diffraction particle size analyzer from samples of HAL Filter feed, shows residues that filter more poorly have a lower Volume Weighted Mean Diameter than those that filter better. INTRODUCTIONHudbay produces cast zinc metal from blends of zinc concentrates at its metallurgical complex in Flin Flon, Manitoba, Canada, using Sherritt’s two-stage pressure leach process (Collins et al., 1994; Collins et al., 1995; Barth et al., 1998; Shairp et al., 2006). Pressure leaching replaced the original roastleach- electrowinning process in 1993.Filtration for the second-stage (HAL) leach residue originally consisted of two stages of vacuum drum filtration with intermediate cake repulping stirred tanks. As part of Hudbay’s 777 Project, with a designed increase in cast zinc production, a pre-feasibility study by SNC-Lavalin Inc. showed that losses of soluble zinc in the zinc pressure leach residue could be reduced by installing more efficient filtering and washing equipment. Based on laboratory performance, capital cost, installation ability, and potential operating cost savings, a 70 m2 Filtres Phillipe belt filter was chosen for the HAL residue, and commissioned in 2000/2001.When the HAL belt filter is performing well, there is no pooling of water on the surface, moisture content is relatively low, and subsequent analysis shows that water soluble zinc content is relatively low. There have been occasions where the filter has performed poorly with respect to the aforementioned parameters. Aside from the filter experiencing mechanical difficulties, there are several variables affecting leach residue filtration:"

Jan 1, 2012

By Adil Aledresse, Louis Mercier, Laxman Amaratunga

"The development of high capacity adsorbents with uniform porosity denoted, MP-HMS (Mercaptopropyl – Hexagonal Mesoporous Structure) using nanotechnology, and their ability to extract gold from solution, is presented. The preparation of highly effective heavy metal ion adsorbents by the incorporation of thiol moieties into the pore channels of mesoporous silica molecular sieves has been the subject of many nanotechnology research investigations. The unique feature of these nanoporous adsorbents is their ability to adsorb gold ions from ultra-low concentration solutions like mine effluent as well as from leached solutions in gold mills. The preliminary studies from laboratory simulated gold solutions show that the adsorption capacities of these materials are also among the highest reported. MP-HMS has shown the capability to adsorb 370 mg gold per one gram of the nanomaterials from Tetrachloroaurate solution (up to 37% of their weight). Experimental studies indicated that the maximum adsorption of gold (as high as 99.9% recovery). The current studies will be extended to investigate the interaction of ionic gold complexes with nanomaterials. Future development of this work may lead to either to replace the conventional CIP/CIL processes or use nanomaterials in tandem with the former, suggesting plausible use of mesoporous material in pulp, MIP or in leach, MIL, as a novel gold extraction process.INTRODUCTIONGold typically occurs at very low concentrations in ores less than 10 g/t or 0.001% (mass basis). At these concentrations the use of aqueous chemical (hydrometallurgical) extraction processes is the only economically viable method of extracting the gold from the ore. Typical hydrometallurgical gold recovery involves a leaching step followed by the separation of the gold bearing solution from the residues, or adsorption of the gold onto activated carbon adsorbent. After elution from the activated carbon the gold is further concentrated by precipitation or electrodeposition."

Jan 1, 2008

By C. R. Larsen, R. G. Bradburn, A. L. Mular, B. C. Flintoff

"Following the acquisition of grinding- circuit data at Brenda Mines Limited for simulation purposes, various methods to mass balance the circuit were evaluated. Unfortunately, different answers were obtained for different balancing methods. A data-adjustment procedure was therefore developed. The procedure assumes that all ""best-fit"" criterion. A search is conducted with the minimum set of water masses and narrow size ranges of solids around the circuit (called search variables), which permit the computation of any of the measured data points. Search variables are used to calculate measured values for an objective function of the form: [ ] where W, is a weighting factor•, M1 is a measured value and M. is a corresponding . value calculated from search vanables. The best values of M, are those which minimize R. The above method is compared with others that have been utilized for mass balancing circuits."

Jan 1, 1976

By Richard J. Wardle, Ambrose F. Howse

The industrial minerals industry in Newfoundland and Labrador is a significant contributor to the provincial economy. The variety ofcommodities produced reflects the diverse geological environment from which they come. A highlight of the past decade has been the continuing development of dimension stone quarries, with producers now active in anorthosite, gabbro, granite and sandstone. Other dimension stone prospects have been identified and are in various stages of assessment and development. Western Newfoundland hosts a large resource of limestone, dolomite and marble. It provides raw material for industries that produce Portland cement, agricultural limestone and aggregate, as well as chemical-grade limestone and dolomite products. In western Labrador, dolomitic marble is quarried for use in the production of self-fluxing iron ore pellets. The recent opening of a new gypsum quarry at Fischells Brook signalled the beginning of a new era in the commercial production ofgypsum, a commodity which the province has produced since the 1950s. Hopefully it will emulate the nearby Flat Bay Quarry (now closed) which was a long-time exporter to markets along the U.S. eastern seaboard, in addition to supplying local demands. Oil production and continuing exploration in the Newfoundland offshore has renewed interest in local barite deposits for potential use in drilling fluids. Already there has been some production from the Collier Point deposit, and at Buchans, an existing plant is being refurbished to recover barite from a large tailings pond. Emerging new industries include the development of an antimony mine in central Newfoundland, the development of silica deposits near Labrador City for silicon metal production, and reactivation of the St. Lawrence fluorspar mine. The province has many deposits with development potential such as rare metals at Strange Lake, white marble at Roddickton and salt deposits near St. George's Bay region.

Jan 1, 2001

By J. W. Matousek

The heat content of the waste slag from a typical smelting operation methods for estimating the thermodynamic properties of smelting slags, to include: -- heats of formation -- heat capacities (specific heats) -- heat contents -- melting temperatures -- heats of fusion The techniques are illustrated with the analyses of a nickel reverberatory furnace slag from Copper Cliff, an iron-making blast furnace slag, and a "lateritic" slag from a ferronickel operation in Colombia.

Jan 1, 2007

By T. H. Etsell, P. Kerr, Qi Liu

"The objective of this investigation was to study the reaction mechanisms during the reduction of iron oxides in the presence of calcium chloride and carbon black as a simplified iron segregation process. The gas phase was analyzed by mass spectroscopy and the solid reaction products were analyzed by scanning electron microscopy. Mass spectroscopy, combined with thermogravimetric analysis and differential scanning calorimetry, revealed the presence of several gases at elevated temperatures over time, and the scanning electron microscope in combination with energy dispersive X-ray analysis illustrated the growth of a metallic iron phase on or near the carbon substrate. The results correlated well with similar copper and nickel segregation processes, but also introduced new insights that challenge the simplicity of the current models. The formation and transport of gaseous iron species to the carbon substrate in the presence of steam and hydrogen were evident during the reduction process that was studied; however, there is more happening at a mineralogical level, based on evidence of a liquid phase resulting in substantial growth due to an apparent fluxing effect created by the calcium chloride.These results help to better explain the chemical reactions and, in turn, the thermodynamics and kinetics of iron segregation processes related to the beneficiation of low grade complex iron ores. The results are also applicable to the production of metallic iron and concentrated titanium dioxide from ilmenite ores. The benefit of this process is that it allows ores in which the iron minerals are intimately associated with gangue minerals to be processed in circumstances where conventional mineral processing techniques are unsuitable or incapable of upgrading the material."

Jan 1, 2016

By Robert B. Parsons

"The Canadian mining industry is not off to a good start in the 1993/94 budget season. Of the five provinces and territories to table budgets as of March 31, 1993, the industry's scorecard shows: one win, one tie, and three losses.IntroductionBy the end of March, five of Canada's twelve provincial and territorial governments had tabled their 1993/94 budgets. The mining industry is off to a bad start. The industry's scorecard shows one win, one tie, and three losses. Only Newfoundland appears to be paying any attention to the industry's concerns about the impact of taxation on competitiveness. It is particularly disconcerting to see that non-profit based taxes continue to increase, at a time when these taxes are the focus of a united attack by the entire industry.NewfoundlandFirst, the good news. On March 18, 1993, Finance Minister Winston Baker announced the following changes to the province's mining tax regime:"

Jan 1, 1993

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By C. Cutts, K. Wheatley

The Dragon Lake Zone (uranium prospect) comprises a N160º trending vein that is approximately 110 m long, up to 5 m wide and from 1 to 40 m high. The zone is mostly within altered sandstone of the Fair Point Formation, the basal unit of the Paleoproterozoic Athabasca Group, but it also extends downward (up to 3.5 m) into basement rocks that occupy the northerly trending Maybelle River Shear Zone (MRSZ). This subvertical shear zone separates graphitic paragneiss and weakly deformed granitoid rocks to the east from non-graphitic paragneiss and foliated granitoid rocks to the west. The Dragon Lake Zone cuts across both the MRSZ and N060º-N070º-trending cross-faults that offset the shear zone but not the mineralized vein, which contains values up to 54.5% U over 50 cm core length. Strong chloritization occurs in graphitic paragneiss and sandstone adjacent to mineralization. Silica was depleted from the basement rocks and redeposited at the borders of the 5-15-m-wide alteration zone, as well as within overlying sandstone of the Manitou Falls Formation. There are minimal alteration effects in the overlying Lazenby Lake Formation. Geochemistry shows that the alteration zone in the Fair Point Formation is highly anomalous in metals, most notably in Ni, As, U, Pb, Co, and B. Clay within this zone is illitic and Fe-rich chlorite is also present. Brittle deformation is not as widespread or as well developed in the Fair Point Formation as it is in the overlying Manitou Falls Formation, which is extensively brecciated and contains some anomalous metal values.

Jan 1, 2013

By H. H. Bleakney

The merit of reduction-in-area as a criterion of quality in metals is shown to lie in its influence on breaking stress, but the virtue of elongation is not easy to find. In order to assess the value of elongation, either as a measure of quality or as a guide to design, it will be necessary to separate the overall de-formation occurring in tension tests from the localized deformation associated with localized reduction in area. The obstacles to a successful solution of this problem have been shown to be more formidable than is generally appreciated, and a new solution to the problem has been suggested. This solution involves a de-vice by which an electric circuit is broken when the particular value of strain is reached that is to be taken as the point of separation between general and localized deformation. The report presents results from a number of tests on both low-carbon and alloy steels. These results indicate that the selected criterion of separation is accurately identified by the proposed method; that it

Jan 1, 1962

Brunswick Mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Feb 1, 2008

By S. P. Chong, N. C. Shih, G. A. Turner

Fine powders, with the bulk of the particle diameters Jess than 10 microns, were aerated so that each particle was, on the average, separated from its neighbours by 1.3 to 2 mean diameters. In this state, measurements were made of the viscosity and settling rate of the powder, and the interfacial tension between it and a moist pellet. From the viscosity measurements, qualitative analogies are drawn between the behaviour of the aerated powder and that of a dense gas near its critical point.

Jan 1, 1970

By François Robert

"The Eastern Abitibi Sub province (Quebec segment), contains two main types of gold deposits: the common quartz-vein type and the rare pyritic type. Both occur in areas dominated by volcanic rocks and are spatially associated with major fault zones.Quartz-vein gold deposits consist of simple to complex networks of quartz-carbonate-pyrite veins in reverse shear zones and extensional fractures. They occur in areas dominated by mafic volcanic rocks and are commonly associated with small syn- to late-tectonic porphyritic felsic intrusions. Associated alteration, which postdates peak metamorphism, is dominated by carbonatization, sericitization and pyritization of the wallrocks. These deposits formed late in the geologicalevolution of the Abitibi.Pyritic gold deposits range from deformed massive sulphide lenses to zones of syntectonic pyrite-rich veinlets and associated pyrite disseminations. These deposits occur in environments dominated by felsic volcanic rocks that are typically converted to sericite schists near the deposits. The associated pre-metamorphic aluminous alteration is now characterized by metamorphic sericite, andalusite, kyanite and chloritoid, overprinted by a late retrogression of alumino- silicates. These deposits probably represent deformed volcanogenic massive sulphide deposits, but the timing of gold introduction in these is not fully understood.The differences in geological attributes reflect significant differences in the genesis these deposits: the pyritic deposits probably have a multistage genesis, including a pre-tectonic stage, in contrast to a single stage late-tectonic genesis for the quartz-vein deposits.RESUMELa partie Est de la Sous-Province de l’Abitibi( segment québécois) renferme deux types de gites d' or: ceux de type ""veine de quartz"" et ceux, plus rares, de type ""pyriteux"". Ces deux types se trouvent dans des secteurs particulièrement riches en roches volcaniques et mantrent une association spatiale avec des zones de failles majeures.Les gites de type ""veine de quartz"" correspondent à des réseaux de complexité variable de veines de quartz-carbonate-pyrite se développant dans des zones de cisaillement inverse et des fractures de tension. Ils se concentrent dans les régions dominées par des roches volcaniques mafiques et s’associent fréquemment à de petites intrusions porphyriques felsiques syn- a tardi-tectoniques. L’altération associée ace type de glte est postérieure à la phase majeure du métamorphisme et consiste en une carbonatisation, une sericitisation et une pyritisation des épontes. La mise en place de ces gites est tardive par rapport à l'évolution géologique de l'Abitibi.Les gites d' or de type pyriteux consistent en des lentilles de sulfures massifs déformes, des zones d' abondantes veinules pyrite uses syntectoniques, et des zones de pyrite disséminée. Ces gites se retrouvent dans des empilements contenant surtout des roches volcaniques felsiques qui sont transformées en schiste à séricine pres des gisements. L’altération a l’umineuse pre-metamorphique associée a ce type de glte a donné naissance, lors du metamorphisme regional, a la sericite, a 'andal ousite, a Ia lcyanite et au chloritoi""de; par la suite, les alumino-silicates ont été affectes par une alteration retrograde tardive. Ces gites representent probablement des depOts de sulfures massifs volcan gènes déformes, mais la chronologie de la mise en place de l'or dans ceux-ci est encore mal comprise.Les caractéristiques géologiques propres à chacun de ces types de gites reflètent des conditions de formation différentes: le type ""pyriteux"" montre une histoire génétique polyphasée, incluant une étape pre-tectonique alors que le type ""veine de quartz"" s’est développe au cours d’une seule phase tardi-tectonique."

Jan 1, 1990

By H. A. Hamza

An experimental study of the settling characteristics of a washery effluent originating as tailings from a froth flotation circuit was undertaken by using a systematic approach to select the most appropriate flocculant(s) under predetermined conditions. Selection and evaluation procedures which greatly reduce the effort required to select flocculants are described. The results show that, although different flocculants display superiority at different ranges of dosage. Separan MG 700 (Dow) is the most suitable on absolute economic grounds. Flocculant evaluation is based on a Cost Performance Index (CPI) which expresses the cost of flocculant (¢/ton) required to produce a unit settling rate (in./hr). From experiments carried out with a number of flocculant aid and flocculant combinations, it was concluded that the use of flocculant aids can be economically justified only if the settling rates required are higher than those obtainable at the optimum flocculant dosage. Otherwise, the value of the flocculant aid appears to be limited largely to the reduction of supernatant turbidity.

Jan 1, 1979

By Martin Kesting

The world wide growth dynamics and the continuously growing demand for energy, results in increasing energy prices. Looking from this point, the efficient exploitation of fossil fuel deposits has become a more important factor to the production of energy raw materials than ever before. This shall be reached by an increase of the automation degree of the bucket wheel excavator in the open pit mining as well as a quality increase of the entire mining process chain. A further optimization of this operation can only be achieved by gathering additional information about the input parameters. The earlier and more exact the description of the input parameter, the greater the effectiveness of the entire process chain. To address this major issue, the RWE Power AG assigned the Institute for Transportation and Automation Technology with the research project "SIMT, Sensory Identification of Material Type and Detection of the Interfaces" [Kes07]. Presently, the control of the bucket wheel excavator is carried out manually by the operator, as well as the visual identification of the different geological layers and the energy raw materials. In this paper, a sensor-system is introduced, which was developed in order to transfer the manual material identification and detection of interfaces into an automatic online procedure. A special challenge and the main focus of this contribution is the integration of this sensor system into a bucket of the bucket wheel excavator. For measuring procedures where direct contact with the in situ material is necessary, the sensor has to be integrated into the bucket. Since direct contact with the material is not necessary, it can be integrated next to the bucket wheel. The results of a preliminary study show that although there is a broad spectrum of sensor technologies for material and interface identification, only a few are suitable for an application in on-line measuring at the bucket wheel excavator. Taking into consideration the demands on the sensor technology, the studies carried out and comparable applications of individual sensor technologies which have already taken place in practice, the integration of the following measuring systems have been realized: ground penetrating radar / reflection measurements, geo electric, resistance geo electric technology. The solution developed in the research project offers for the first time the direct integration of sensor systems into the bucket of a bucket wheel excavator. It will now be possible to test other measurement methods and sensors, not only for the ones already mentioned. As an example the integration of a triaxial accelerometer to measure the solid borne sound and vibrations concerning the cutting of different materials will be shown.

Oct 1, 2009

By D. W. Zandee

"IntroductionHaving mined an economic mineral bearing rock which is of insufficient grade to warrant direct smelting, upgrading or beneficiation is required to make it an economically viable ore. The first step in effecting the concentration process is comminution or sequential breaking of the rock to allow liberation and subsequent recovery of the desired mineral particles. Desirably the ore could be broken down to the point where the valuable mineral is completely liberated to maximize the chance of recovering as much of it and in as pure a form as possible. The number of energy intensive stages of breakage required to attain this goal depends on many physical characteristics of the ore such as hardness, friability, toughness, grain size, existing fracture planes and particle shapes.Commonly the distinct stages are primary, secondary and often tertiary crushing and finally grinding. To increase the efficiency of each stage of size reduction, pre-treatment sizing is common.Crusher feed is commonly scalped of large pieces or screened for reduction crushers and classified for secondary grindingcircuits.Although crushing and screening is employed for many different products, this chapter reviews current practice in larger tonnage metalliferous ore treatment plants.Current practice is to use large gyratory or jaw crushers for primary crushing and some sort of gyrating or cone crushers for additional stages of reduction. For autogenous or semiautogenous grinding circuits only the primary crushing stage is necessary, the balance of the work being performed in the grinding stage. For conventional grinding circuits using ball mills or combinations of rod and ball mills, secondary, tertiary and even quaternary crushing stages are normally required.Older type crushers such as stamp mills, double rolls, sledging mills and hammermills are no longer common but are used for small tonnage special processes.Important to efficient crushing are a variety of sizing devices such as grizzlies and vibrating screens. Products at different stages must be stored to give surge capacity and allow controlled feeding rates through mechanical and gravity feeders. These storage piles, bins and feeders as well as crushers and screens are commonly integrated into a total facility by means of conveyor systems. Most often these are endless rubber belts driven by simple or multiple drive mechanisms usually consisting of electric motors and speed reducers."

Jan 1, 1989

By C. A. Lavery

A DISCUSSION is presented of natural gas production and field processing equipment as now utilized in the gas producing areas of the United States, with reference to use of such equipment in Canadian gas areas. The scope of the paper is confined to a general description of various types and methods of using surface production equipment. The discussion is divided under two general groups: well-head production equipment, and field processing. The first will be concerned primarily with indirect heaters, separators, knockouts, and special versions of this equipment. The second major group includes the field processing equipment for handling natural gas. A delineation should be made here as to the meaning of field processing as used in this discussion. We will limit our term to mean such processing equipment as may be used in producing fields to process gas or its by products in a manner that does not require conventional plant practices either in operation or supervision. This covers such equipment as is necessary to complete preparation of gas for sale to pipeline and/ or is necessary to recover valuable components. Under this heading we will discuss glycol dehydration, solid desiccant dehydration, low-temperature separation, mechanical refrigeration, and desorbtion-stabilization. These are all processes involved in preparing gas for final sale or disposal. They do not include the more conventional and large-scale plant process systems.

Jan 1, 1956