Search Documents

ALTHOUGH discovered as long ago as 1817, by Strohmeyer, the use of cadmium did not become in anyway general for nearly a century. Its properties, although well known, did not recommend it to users of metals generally, and it was, on the whole, regarded more in the light of a nuisance to zinc producers than anything else. Its real value was not appreciated until both the United States of America and Germany, who are entirely dependent on outside sources for their supplies of tin, were faced with the unpleasant fact that their tin stocks were being rapidly depleted, with practically no prospect of having them replenished. This resulted in serious efforts being made in the UnIted States of America to conserve what tin was available, and, as a consequence, several metals were tried in the hope that they would prove satisfactory substitutes for tin. Among these was cadmium, and it was found that cadmium could replace tin in a manner sufficiently satisfactory to permit of its use in many directions where tin had been used before.It is on this ability of cadmium to replace tin that its use became in any way general at first; but since then new avenues of development have been opened up in which its physical and chemical properties are proving their value. It is highly probable that its use will extend very considerably as time goes on. OCCURRENCE OF CADMIUM.There are several cadmium minerals known, but none of them occur in profitable quantities as ores. The cadmium of commerce is derived almost entirely from zinc minerals and ores in which it is almost invariably present in proportions which are usually very small. Cadmium behaves metallurgically almost the same as zinc, and hence constitutes a fraction of 1% of almost all spelter.

Jan 1, 1923

By Misk A

Several logging methods are presently available to the oil industry for the evaluation of formation porosity: the Sonic and Neutron logs are already widely used, the Gamma-Ganmia log is being progressively introduced. The readings of these instruments are primarily a function of the rack-porosity, hence the general term of "porosity tools". Apart from porosity, however, other variables such as type of fluid in the pores, nature of matrix and degree of shaliness have an important influence.The response of each device is a different function of such parameters: therefore, a cci bination of porosity tools can lead to information on these variables in addition to the evaluation of effective porosity.For example, the presence of gas; rather than water or oil, in a formation which is not deeply invaded, will tend to give Neutron derived porosity values which are too 'low; on the other hand, the Sonic derived porosity: value will be too high in such- a case. For the same porosity, the Sonic gives a longer transit time in sandstone than limestone, whereas in the low porosity range, the Neutron will read more counts per second in a sandstone than in a limestone of the same porosity. The presence of shale also affects the readings of the various porosity tools in different ways so that the combination of two or more methods may lead, in some cases; to an evaluation of both the-effective porosity and the shale, content.In conclusion, it may be said that the various porosity tools pre-sently available, are, to a large extent, complementary, and that in many problems the use of two porosity tools, instead of one, is very likely to bring valuable additional information.

Jan 1, 1962

In Australia we usually define "resource" in purely material terms, and rarely relate it to intellect and human capacity. We look at the sheer abundance of our natural resources and are satisfied with the feeling that we don't really need-to rely on using our brains. Certainly our country is fortunate to have the mineral resources it does, but in many ways Australia's worst enemy is its "lucky country" syndrome because we tend to underutilise the great resource we have in the capacities of our people. Raw material exports will undoubtedly continue to contribute a major share of our export revenue, but to harness the riches our country has to offer most effectively we need the vision and planning necessary to bring together our material and human resources. There is a need not only to find, exploit and process our minerals economically, but to turn as much of our mineral wealth as possible into high value products before it leaves the country. In particular we must use our brainpower if we want to maximise economic benefit from and political influence over the strategic minerals which leave our shores. In the past we have been successful in finding and exploiting minerals because our mining industry has been in the forefront of private sector research and development. But if Australia is to have an advantage over other mineral rich countries in insulating itself from the effects of cyclical swings in commodity prices, then the future of the industry must lie even more in technological sophistication rather than depending. on such considerations as size and location of mineral deposits. To survive, our mineral industry must have the foresight and resourcefulness to make its own luck. There are two keys to increased efficiency in exploration and production and in further processing methods: enhancement of the skills of the workforce and continual improvement of R&D.

Jan 1, 1986

Australian wheat belt agriculture is causing a decline of its natural resource base. The major problem, salinity, arises from a small reduction in water consumption by agricultural crops compared to what prevailed under the prior native vegetation. This causes groundwater accumulation which, in the low relief landscapes of the wheat belt, is leading to extensive surface saturation in low landscape positions and dramatic, destructive change in the hydrological behaviour and habitat of streams and rivers. The ability of agriculture to invest in salinity control is severely limited by its long-term decline in its terms of trade. Extensive planting of perennial vegetation has the potential to increase water use and arrest the salinisation process. If these perennials were also commercially attractive, the cost of salinity treatment could be minimised. Given the difficult commercial position of food commodities, it is logical to develop ænon-foodÆ perennial crops, in particular woody crops suitable for industrial products. This paper looks at the example of Sweden, where there has been a generation of investment in developing forest harvest residue recovery, and short cycle woody crops for bioenergy, but with only limited success. In contrast, secondary residues (processing wastes) from forestry industry are readily saleable for low value uses like bioenergy. This suggests that the model woody crop must have a higher value fraction to facilitate delivery and commercial use of its lower value fractions. This model is being emulated in the development of native mallee eucalypts as short cycle woody crops in Western Australia. Some $50 million has been expended on mallee development in the past decade and this has culminated in an engineering demonstration of integrated processing. The putative high value products are activated carbon and eucalyptus oil and the residue (plus waste heat) will be converted to electricity. The potential scale on which crops of this type would be required to achieve salinity control means that many more high value and residue products will have to be developed. Metallurgical charcoal appears to be a promising product option.

Jan 1, 2006

Structural geological modelling is a process which results in a 3D computer model that represents the essence of the geological and structural understanding of an area and is presented in a way that is directly useable, typically by internal customer groups. BHP Iron Ore operates a number of open cut iron ore mines in the Pilbara Region of Western Australia. The largest mine is the Mt Whaleback Mine located at Newman close to the southern margin of the Pilbara Craton. The structurally complex Mt Whaleback Mine is the largest metalliferous single pit open cut mine in Australia with over 1.6 billion tonnes of original iron ore resource. Additional to the Mt Whaleback Mine, a number of satellite open cut iron ore mines are operated by BHP Iron Ore (BHPIO) in the Newman area. BHPIO also operates the Yarrie mine approximately 400 km north of Newman at the northern edge of the Pilbara Craton Most of the BHPIO mines are located in the Archean- Proterozoic Hamersley Province that overlies the Archean granite-greenstone terrain of the Pilbara Craton. The orebodies are considered to be the result of supergene enrichment of the approximately 2.5 Ga Brockman Iron Formation and the slightly older Marra Mamba Iron Formation. Folding represents the most prevalent and penetrative structural element in the Newman area. Four folding phases have been identified regionally (Fj, F2, F3, F5), while a more local folding deformation (F4) developed mainly in the Mt Whaleback and Orebody 29 mine area. A northeast trending, southeast dipping, 45 km long, high angle, normal fault zone, the Whaleback Fault Zone, cuts through the Mt Whaleback mine resulting in an approximately 1400 in gap in stratigraphy. Additionally, two large, low angle, normal faults, the East Footwall Fault and the Central Fault, are present at the Mt Whaleback Mine. During the formation of supergene orebodies, up to 40 - 45 per cent volume loss occurred resulting in local non-tectonic deformation in the orebodies.

Jan 1, 1997

The perennial challenge facing mining and minerals operators is to improve productivity, usually by a combination of cost reduction and performance improvement. In a typical production situation involving mining and processing activities, the standard approach has long been to seek improvements in each activity, effectively in isolation from each other. However, the realisation is growing that there is considerable potential to achieve really substantial productivity gains by much improved integration of mining and processing with the key being to consider what is best in the total sense. Some of the linkages between fragmentation in mining and downstream processing are considered in this paper. These linkages involve technical, operational and economic Considerations.

Jan 1, 1997

In recent decades the awareness of environmental issues by the general public has developed at an accelerat- ing rate. This is the result of a number of factors including more scientific knowledge of environments and of the impacts of modern society upon them, higher levels of education, the opportunity for people to travel more, and the success of the various communication media in bringing in- formation to the communities of the world about such environmental crises or threats as the smogs of Los Angeles and London, the Torrey Canyon and Santa Barbara oilspills, Minamata disease in Japan, the spread of the Crown of Thorns starfish, the disposal of toxic industrial wastes into the Upper Rhine, the discovery of high mercury and zinc contents in marine foods in southern Australian waters, and the proposal to mine limestone at Precipitous Bluff in Tasmania.

Jan 1, 1975

By L Ryan, S Halley

The use of a field spectrometer to systematically analyse drill samples from over 200 holes around the Permian-Carboniferous Ravenswood gold deposits in north-east Queensland has successfully identified both small and deposit-scale changes in the alteration mineral chemistry. Changes in chlorite composition within the tonalite host rocks are evident at the district scale, with Fe-rich chlorites seemingly more common in the vicinity of the deposits. Significant variations in white mica chemistry also occur, but mostly on the vein selvage scale, with no clear distinction between near-mine and distal compositions. The results indicate that chlorite compositional maps produced from regional field or airborne spectrometer data could potentially be used as a vector to ore in exploring for similar deposits in the area. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The Key Centre for Mines consists of the School of Mines of the University of New South Wales and the Departments of Geology and Civil and Mining Engineering of Wollongong University. The Key Centre for Mines/International promotes, markets and develops overseas activities in applied geology, mining engineering, mineral processing and extractive metallurgy specifically in response to the perceived needs in the region for mineral resource and other related earth-science based development. the Key Centre for Mines/International will be involved in the overseas marketing of formal courses; special training activities such as short courses and in-house programs; technical and educational consultancy; research and development projects, and in the establishment of regional links through twinning, exchange and various network arrangements with other organisations in the region. Activities which are now being developed include a training program for Korean mining engineers and geologists, teaching and curriculum development in the Mineral Resources Engineering Faculty of the University Sains Malaysia and a staff development proposal for the Department of Geotechnology of Khon Kaen University, Thailand

Jan 1, 1990

By Hopkins G. M F

Intensive exploration of the Archaean ultra mafic sequence bordering the Kambalda dome has resulted in the discovery of at least ten dis- tinct areas of nickel sulphide mineralisation subsequent to the initial drill intersection in January, 1966. Sulphide ore reserves to June 30, 1972 were 19.36 million tonnes at 3.3% nickel after mining of 3.0 million tonnes at 3:7%,nickel since production commenced in March, 1967. About 75% of contained nickel metal reserves occur in sulphide concentrations located at the base of the-ultramafic sequence, in contact with underlying meta-tholeiitic basalt. The remaining reserve occurs in concentrations of sulphides within the ultramafic sequence, usually within 100 metres of the underlying contact and typically in proximity to contact mineralisation. These hanging wall orebodies are smaller, contain significantly lower con- centrations of sulphide, and generally exhibit higher Ni:S ratios than underlying contact ore- bodies. The majority of contact sulphides concentr- ations form narrow, elongate, north north-west trending bodies, closely coincident with fault bounded depressions in the contact. Detailed study of the Lunnon Shoot ore environment in- dicates that it was a locus of crustal failure during, and subsequent to, emplacement of ultra- mafic rocks. Resultant structures parallel and

Jan 1, 1973

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By M Roper, M Lovitt

WMC Resources Olympic Dam Operation located in South Australia, is a poly metallic underground sublevel open stoping (SLOS) mining operation with a current annual production rate in excess of 9.0 Mt. Stope size, geometries, geotechnical considerations, drilling and blasting are critical components in stope performance. These factors are further influenced by stringent ventilation requirements due to the presence of airborne radioactive contaminants from uranium mineralisation. Stope planning is complex and mass blasting methodologies have been trialled at Olympic Dam with the view to reducing the frequency of stope blasts, improving stope stability, productivity and ultimately improving overall stope performance. A key aspect in the ability to undertake underground mass blasts of this scale is the application of i-konTM electronic initiation technology by Orica. In the past two years in excess of three million tonnes has been initiated utilising this electronic technology, with an average blast of 250 000 t ranging to the largest to date being 580 000 t. By providing flexibility in blast designs, the use of electronic detonators has allowed mass firings over multiple sublevels. This has resulted in a significant reduction in stope extraction steps compared to conventional pyrotechnic firings. The benefits of this reduction in the number of stope blasts are wide ranging from improved stability of interim stope voids between blasts, reduced blasthole damage, improved blast vibration management and reduction of complex changes to ventilation systems for blasting.

Jan 1, 2004

Welcome to this 13th Congress of The Council of Mining and Metallurgical Institutions. It is twenty one years since The Australasian Institute of Mining and Metallurgy last hosted this congress and it is a privilege and a pleasure for The AusIMM to have that responsibility once more. The theme of this congress "The Twenty-First Century - Mining for Mankind" stimulates many thoughts. The first thought that it generates in me relates to the reference to the 21st Century. We are still 14 years away from it and already consideration of the beginning of the next millenium is becoming something of a cliche. If we feel like that about it now, how will we feel at the 14th Congress of the CMMI in 1990, or the 15th in 1994 or the 16th in 1998? If we do all the crystal ball gazing about the 21st Century this week, those poor devils in the 1990s will in fact have nothing to talk about. Of course that is not the case. This is a very appropriate time for those of us concerned with mining and metallurgy to contemplate the next century. Fourteen years is about the extent of forward planning necessary in the mining business. I sometimes feel that most people do not take seriously the need for long range planning in our industry. Politicians, investment fund managers, and others under severe short-term pressure to perform in our hyperactive world may nod in apparent appreciation of our long term plans but their actions in the interests of expediency often betray-them.

Jan 1, 1986

By P G Simpson

The Sundance gold mine, located 2.5 km east of the town of Batchelor in the Northern Territiory, has produced over 5300 oz of gold since it was discovered in 1978. Sundance is unique in the Pine Creek Inlier in that the ore is hosted in palaeo-karst detritus and crystalline magnesite of the Early Proterozoic Coomalie Dolomite. This paper presents a summary of the geology of the mine, and describes the methods used during the two periods of mining.

Jan 1, 1994

That gold will dissolve in sodium hyposlphite solutions is known from the lixiviation of silver and gold ores.The gold will dissolve only in small quantities. According to Stetefeldt, if gold leaf is treated for a time with sodium hyposlllphite solutions of varying strengths solution takes place in every instance, the deviation in quantity being very slight.In order to form hyposulphite double-salts, the gold must become oxidised, the oxygen being derived from the air absorbed by the solution. Consequently, it is the quantity of free oxygen in the solution by, which the reaction is determined, as for one equivalent of gold dissolved one equivalent of caustic soda is set free.

Jan 1, 1901

The annual growth in lead consumption in the Western world has declined sharply in the past ten years, as lead has suffered a wave of substitution by other materials, and has also been the object of concern about its toxicity in daily applications. Like most metal industries, the lead industry has tended to be more production-oriented than market-oriented than is the case with some of its competitors. However, in recent times this pessimism and preoccupation with weathering the threats from environmental legislation, substitution and low prices appears to have been replaced with a new optimism in some sectors of the industry. This is indicated by renewed promotional activities and efforts to find more applications and market opportunities.

Jan 1, 1985

The use of ammonium nitrate/fuel oil explosives is.now well established in most open cut mining operations. Its use. is extending to underground mining. This has been due in a large measure to improvements in the nature of the ammonium nitrate made available from various sources. The addition of surface active agents and water in controlled amounts to the fuel oil has been found to increase the sensitivity of the ANJFO mixture with consequent better explosive properties. It is considered that the surface active agent increases the bond between the ammonium nitrate and fuel oil giving a more, intimate physical and chemical mixing of the oxidising and reducing agent. This results in increased sensitivity and a faster rate of reaction. The increase in sensitivity has been accomplished without any diminution of safety. Tests which demonstrate the safety of this type of explosive are given in the appenuix.

Jan 1, 1964

By D Ryan

Following a long period of increase, there has been a reduction in exploration expenditure and activity in Australia over the past two years. During the post Second World War period, exploration was largely driven by mining companies seeking resources to satisfy an increase in world demand, while increasing their asset base as a result of mineral discoveries. In general, return on investment to shareholders was not the major driving force. With the exception of gold the mining industry has been faced with a long-term fall of metal prices in real terms. As a result the net profit return on average shareholderÆs funds in the Australian minerals industry has fallen from over 20 per cent in 1990 to less than five per cent today. Mining is now competing for funds with communication and finance based industries yielding high returns on shareholder investment. Shareholders and superannuation fund managers seeking a high return on short-term investments have indirectly reduced the funds available to the mining industry. Globalisation of the mining industry is leading to the rationalisation of the Australian mining industry as witnessed by mergers and acquisitions of local companies by foreign investors. The return on capital invested in the Australian mineral exploration industry must improve if the industry is to be competitive on a worldwide basis. Failure to achieve this will result in capital flowing overseas or to other industries. Relatively short-term upswings in metal prices which are generally driven by threats to the supply base (eg strikes, mine closures, increases in country risk) often lead to increased capital raisings for exploration funding. As a consequence of the time taken to raise the capital and increase exploration activity, measured exploration activity lags the metal price increases. There are also lags between commencement of exploration and discovery and ore production. In the case of gold exploration expenditure peaked six years after the price rise of 1980 Companies persevering with exploration in the current difficult period will be rewarded because they will be able to capitalise on future metal price rises and a minimised time lag.

Jan 1, 2000

The JORC Code, which has been in existence as a Code incorporated in the listing rules of the Australian Stock Exchange and New Zealand Stock Exchange since 1989 and 1992 respectively, has been revised and will be re-released in 2003. This revision followed a call for submissions in December 2001, the publication of an exposure draft in late-2002 and an exposure period during which a large number of constructive comments were received. These comments were reviewed and a further exposure draft released as part of the current exposure draft of the ASX listing rules. It is anticipated that the final Code will be incorporated into the stock exchanges listing rules in late-2003. The 1999 JORC Code has been the standard on which other reporting Codes have been based, each of which has contained refinements. Three in particular, the Reporting Code from the United Kingdom/Ireland/Western Europe, the new Canadian Reporting standards and the SAMREC Code from South Africa, influenced JORC in the preparation of the 2003 JORC Code. Whilst there are differences between the 1999 Code and the 2003 Code, these changes are mainly in the guidelines. The Code definitions, which are largely in accord with agreed international definitions, remain substantially unchanged. The two main changes in the 2003 Code are the requirement for a Competent Person to be responsible for the documentation relating to the reporting of Exploration Results, and the introduction of æRecognised Overseas Professional OrganisationsÆ as overseas organisations to which Competent Persons may belong. Other changes include: clarification of the reporting of exploration targets or potential; the rearrangement of the diamond reporting clauses; the introduction of guidelines for the reporting of Industrial Minerals; modification of the coal clauses and recognition of the new Coal Guidelines; and the introduction of a guideline encouraging the discussion of relative accuracy and confidence in resource/reserve estimates. Other lesser changes to the Code are listed and discussed briefly. The release of the 2003 JORC Code maintains the standard set by JORC as a world leader in the development of mineral reporting Codes and their adoption by industry.

Jan 1, 2003

Pyrrhotite is pyrophoric when in a finely divided form. The problems of disposing of large quantities of finely divided pyrrhotite separated out by metallurgical processing from ore are formidable. In the case of an underground mine, a solution to the problem of disposal is to place the pyrrhotite in the stoped out areas and seal from any air supply. Further, the pyrrhotite could be diluted with tailings which would reduce the possibility of combust- ion. Several enquiries to various centres and authorities have shown that the products of the slow oxidation of pyrrhotite with moisture present can cement an inert matrix into a stable fill similar in physical prop- erties to fill stabilised with Portland cement. Stabilised fill can be used to advan tage with a suitable mining method to provide high recovery. The investigation demonstrated that air and 15% w/w water must be present for the fill to harden and that the sizing of the particles is a critical factor in drainage of a hydraul- ically placed fill and subsequent even harden- ing of the fill in a stope. With the materials used in the experiments in which the - 51 micron component of the tailings had been dis- carded, an optimum mix was found to contain 4:1 tailings/slag ratio and an overall pyrr hotite concentration of 8% (all proportion by weight). Approximately 34 days after drain- age to 15% moisture in natural air flow condit- ions, an unconfined compressive strength of 1.862 MPa was attained. A subsequent experi- ment was conducted with a sample of optimum mix in a pipe one metre long in forced air flow conditions. At a superficial velocity of 3.Om per hour the mix required 155 hours to harden to 1.862 MPa after drainage to 15% w/w moisture content. The pressure drop bet- ween the top and bottom of the mix in the pipe remained constant at 9 KPa/metre length. This result suggests that forced air flow conditions will increase the rate of hardening. No dangerous effluents were detected in the course of the experiments which could affect mine equipment or personnel.

Jan 1, 1973