Search Documents

By Borsaru M, Wylie AW

A neutron irradiation technique has been developed which is suitable for the determinat- ion of the iron and aluminium content of iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. The determination of iron entails measure- ment with a NaI(Tl) gamma ray detector of the characteristic prompt gamma rays (7.64 MeV) due to thermal neutron capture in iron, while the determination of aluminium is based on thermal neutron activation analysis. For the latter a second detector must be placed down- stream to monitor the 1.78 MeV gamma radiation emitted after activation of aluminium. Although conveyor speed has no effect on the Fe measurement, it has an adverse influence on the aluminium signal, and the belt speed should not exceed 0.1 m/s if good accuracy is required. Static trials on a 460 mm rubber conveyor belt with constant ore geometry indicate that for iron an accuracy of ¦ 1.2% Fe (2a) can be achieved for crushed run-of-mine ore at

Jan 1, 1978

This paper will describe the exploration project which led to the discovery of the La Escondida porphyry copper deposit in northern Chile and will serve as companion paper to the description of the geology of Escondida being presented by J M Ojeda. The author would like to express his appreciation to Robert Hickman, Chairman of Minera Escondida, for permission to present this paper.In July 1978, a proposal was made by J D Lowell to Robert Wheaton, then Exploration Manager of Utah International, that Utah fund a "grass roots" program exploring for porphyry copper deposits in northern Chile. Wheaton expressed interest, and it was agreed that Getty Oil Co also be invited to participate. A joint venture agreement for the Atacama Exploration Project was signed January 1, 1979, between Utah, Getty and Lowell. The project was managed by Lowell who reported to a management committee which through most of the project consisted of Lowell, Francisco Ortiz, Robert Wheaton, Maurice Young, Sigfried Muessig and Louis Rove. Oliver Warin and Jim Bratt participated in the committee in the last phase of the contract. Special thanks are due Louis Rove of Getty and Maurice Young of Utah who made contributions throughout the course of the project. Francisco Ortiz was resident manager through most of the project.

Jan 1, 1990

By E du Plessis, M Rowley, M Fallon, F Golenya, R Swanson, I Robertson

"Check sampling programs were undertaken at Barrick Australia Pacific LimitedÆs Lawlers and Plutonic mine sites in Western Australia. The programs identified that the sampling, sample preparation and assaying protocols required modification to ensure acceptable precision (reproducibility) for each gold mineralisation type. These case studies describe the processes used to identify the: inconsistent precision different types of test work programs that were conducted to quantify the appropriateness for each mineralisation type steps used to modify the protocols.The type of test work conducted included: a duplicate series heterogeneity test for particulate gold mineralisation in the Lawlers gold deposit screen fire assay test work on duplicate subsamples for arsenopyrite associated mineralisation at the Plutonic gold deposit.Each test work program required a detailed scope specifying the sample selection criteria, sample preparation and assaying steps. The aim of the test work flow chart design was to ensure the assay precision between the different particle sizes or duplicate sample pairs could be measured and calculated. In the screen fire test work the true grade of the primary sample was calculated and compared against each subsample.A high quality assay laboratory was utilised for the test work. All samples were fire assayed and the gold grade determined using a gravimetric finish. The assay results were validated and the data was analysed using tables and graphs in spreadsheets. Following data analysis a modified sample preparation and assaying protocol for each mineralisation type was designed for use by the principal assay laboratories. Following implementation of the new protocols, routine check samples were collected during the sample preparation and assaying stages to monitor the performance of the new protocol.CITATION:Fallon, M, Rowley, M, Du Plessis, E, Golenya, F, Robertson, I and Swanson, R, 2012. Confirming the sampling, sample preparation and assaying protocols used at two Yilgarn gold deposits, in Proceedings Sampling 2012, pp 47-62 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By P A. Dowd

This paper describes an integrated approach to the evaluation of ore loss and ore dilution via geostatistical simulation of in situ geology and grade characteristics, simulation of blasting mechanisms and simulation of loading from a blast muck pile. The approach is demonstrated on a case study. The sequential Gaussian method is used to simulate in situ bench grades on the scale of the smallest selectable volume within a blast muck pile. The simulated grades of these component volumes are interpreted as the reality that would be available with exhaustive sampling. The simulated bench is subjected to a blast simulator, based on the SCRAMBLE model, which effectively moves each of the component model volumes to its final resting place in the blast muck pile. Ore/waste delineation and selective loading processes are applied to the simulated muck pile to determine the degree of selectivity that can be achieved by various sizes of loader and types of loading and to quantify ore dilution and ore loss. An in situ model representing the reality of knowing only the data and information that are available from specific grade control drilling and sampling grids is obtained by sampling the geostatistically simulated model on a specified grid. The volumes comprising the in situ model are then populated by estimates based only on the data and from the specified grade control drilling and sampling grids. Different drilling and sampling grids are used to generate different models, each reflecting the levels of data and information available. Selectivity is assessed as a function of the drilling and sampling grids as well as the size and type of loader. Performance is assessed against the ideal selectivity that could be achieved on the perfect knowledge model comprising the simulated values of each component volume. Costs, prices and financial criteria enable an optimal selection of the grade control drilling grid, size of loader, type of loading and blast design.

Jan 1, 2004

By Galecki G

The investigations conducted in the High Pressure Lab at the University of Missouri-Rolla demonstrated the ability of high pressure waterjets to excavate coal and minerals, disintegrate materials and as well as to comminute coal and minerals. Additional progress in comminution can be achieved if the compressive crushing principle commonly used at present is changed to one where particles are fragmented by the tensile growth of preexisting internal flaws or cracks, under internal waterjet pressure. This idea was studied in a number of tests. It covers tests with different jets imposed on coal and rock samples during compressive load as well as without any loading.

Jan 1, 1993

By A Logan, B Cuthbert

Brown and Chitombo (2007) indicated that during the last two decades, the international mining industry has been using mainly mass mining methods to extract safely and economically some of the important commodities such as copper, diamonds, gold, iron and nickel. Mass mining may be implemented either on the surface through large open pits or underground using mining methods such as sublevel, block and panel caving. Developments in the last ten years have demonstrated that caving methods can be applied successfully in strong orebodies at greater depths and in increasingly challenging geotechnical environments for which more traditional mining methods would be unsuitable, unsafe and/or uneconomic. These underground mass mining challenges require æfront endÆ investigation and analysis, robust engineering design and disciplined implementation and operation. Newcrest Mining Limited has focused its efforts on the development of gold/copper projects of substantial scale and margin. To help achieve this, the company is applying and further developing mass mining methods. These include large-scale open pits (OP) and underground mining methods such as sublevel (SLC), block (BC) and panel caving (PC). Block and panel caving now offer economies of scale opportunities for Newcrest to achieve high production rates at lower production costs; thus enabling the exploitation of mineral endowments at higher margins. This paper discusses the practical aspects of caving technologies that Newcrest continues to develop through its expertise at Telfer and Ridgeway SLC operations, Ridgeway Deeps BC and Cadia East PC projects.

Jan 1, 2008

EQUIPMENT TO BE DISCUSSED It is the intention of this paper to discuss the transporting of large skid mounted equipment and track machines around open cut mines. By large I mean 100 to 350 tonne capacity being trans- ported on minesite lowloaders and the capability of moving loads of 300 to 1200 tonne by other means. It is also possible to move larger loads. The main factor in transporting large loads is eco- nomics and is a balance between the cost of the transporter and the increased production from the equipment being moved. For example it could be possible to shift a 7000 tonne dragline faster than their own means of propulsion, being the "walking feet" method. However for the cost of $10 to $12,000,000.00 or more you can afford to walk the dragline and suffer the production loss. Let us concentrate on the economically realistic. BOSICH FBT MINESITE LOWLOADERS 100 TO 350 TONNE CAPACITY. Why initially consider having such a transporter? Our experience has shown that initial enquiries evolve from mines requiring to move large drills, 50 to 200 tonne weight and large hydraulic excavators or backhoes which are track mounted. The reason for shifting them is to move equipment from a mining face to enable blasting, to remove to the central workshop for repairs, overhauls and routine maintenance, to transport equip- ment from one mine face to another, and for drills, to move from one drilling pattern to the next. The cost in terms of time lost and extra wear on tracked equip- ment easily justifies the cost of the transporter. The tracks on large drills and shovels are not intended for long distance walk- ing. These tracks are designed to move the machines to position for drill holes, or moving around the mine face. Long distance travel, ie generally 1 km or more, results in overheating of track rollers, track drive components and accelerated wear on tracks.

Jan 1, 1989

Underlain by and intruded into the sedimentary rocks of the Transvaal Supergroup the Bushveld Complex is the largest known layered intrusion in the world and contains one of the richest ore deposits on earth. It has been the world's major source of Platinum Group Metals (PGM) since the mid-1900s with Chromite and PGMs the two most economically important components of the Bushveld Complex. The lower group (LG), within the critical zone, consists of seven chromitite layers and it is within this sequence of chromitite layers, the most important target of the lower chromitite group is found, ie the LG6 chromitite unit. The LG6 chromitite unit consists of a chromitite duplex composed of the lower LG6 chromitite layer (Steelport seam), averaging 1 m thick, overlain by a 0.66 m waste parting and a thin 0.34 m thick LG6a chromitite layer (leader layer).Two mining methods are commonly applied in the Bushveld Complex to extract the LG6 chromitite layer package. One method consists of footwall development utilising rail bound equipment to gain access to the orebody and then extracts only the LG6 chromitite layer by means of hand held rock drills and scraper winches. The second method is the use of mechanised equipment to access the orebody on the plane of the ore utilising bord and pillar mining method, which extracts the full mineral resource, ie the LG6 and LG6a layers. Conventional narrow vein stoping is often selected due to the large conventional mining skills base found in South Africa, the perceived cost and dilution implications of utilising mechanised equipment, and the difficulties of using mechanised equipment at dips above 12¦. The driving factor for mechanised mining is the perceived ability to access the orebody quickly and inexpensively, and extract the entire mineral resource package (LG6 and LG6a) while limiting capital expenditure and improving safety.This paper investigates these two commonly applied approaches, highlighting the benefits and problems associated with the two approaches. Comparisons will be made of the two mining methods and recommendations given for the mining engineer to consider before selecting the appropriate mine design.

Dec 6, 2010

By Farrelly C. T

The Wiluna mining operations are centred near the township of Wiluna 750 kilometres north-east of Perth and 600 kilometres east of Geraldton.The Wiluna gold mines produced over two million ounces of gold, predominantly by roasting the refractory sulphide ores, before closing in 1947. In the period 1984 to 1992, 668 000 ounces of gold has been produced from free milling oxide ores and the retreatment of tailing. A plant capable of treating the refractory sulphide ores using the bacterial oxidation, Biox technique was commissioned in March, 1993.The Wiluna lode deposits are hosted by a sequence of very low grade metamorphosed mafic flows at the northern end of the Norseman-Wiluna greenstone belt. A strike slip fault system provided conduits for fluid migration; ore deposition occurred at favourable sites along the faults. Satellite mines at Gourdis and Wiluna South provide laterite and lode style oxide ores.The different styles of deposit and ore types at the Wiluna mining operations require a flexible approach to resource estimation and grade control practices.

Jan 1, 1993

By Thorburn D

This paper reviews the history of environmental assessment in New Zealand with reference to mineral developments. Emphasis is given to larger more controversial projects particularly metal mines. The changing role and application of the Environmental Protection and Enhancement Procedures is examined in the context of changes in the government's environmental administration and the response of the Ministry of Energy's resource allocation group. Conclusions are drawn on the effectiveness of the present environmental assessment activities and on the allocation of administration of priorities in the Ministry. The Ministry of Energy has effectively ceased to exist.

Jan 1, 1990

By Bowden MW

Sintering of lead-zinc concentrates is practised by Sulphide Corporation to provide both desulfurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulfur dioxide gas for sulfuric acid manufacture.Moisture control of feed mixes is of paramount importance in the sintering operation and improvements in this area have realised increases in overall plant performance.

Jan 1, 1985

The application of new and currently practised mining techniques in new areas and at greater depths necessitates considerable and immediate research effort. This effort is aimed at identifying the factors which make a particular method suitable and economically viable in a given geological, structural and operational environment. These factors, together with greatly enhanced knowledge of a deposit at the exploration and planning stage, allow selection of the most appropriate and efficient mining method in a new area such that coal resource recovery is maximised in a cost effective manner. Current research and future requirements for research into mining methods and associated equipment and mine services are reviewed.

Jan 1, 1981

By Houchin MR, Jenkins DH

This paper examines the importance of processing to the properties and performance of high purity zirconia ceramics. Many of the principles discussed, however, apply to ceramic processing in general. For fabricated ceramic articles to display their wide range of high performance properties, they must be made fully dense. The precursor powder and postpowder processing requirements necessary to achieve full density in the fabricated body are discussed. Brittleness, the anathema of ceramics, can be overcome in zirconia by incorporation of toughening mechanisms. Transformation toughening and microcrack toughening and their origins in partially stabilized zirconia are reviewed.

Jan 1, 1989

Although giant strides have been made in the Australian mineral industry over the past quarter of a century in terms of mineral discoveries, self-sufficiency of commodities, contributions to exports and other aspects, there are unhealthy signs emerging which require attention. For instance there are 20 out of 34 discoveries of base metals, uranium and nickel which for a number of reasons await development. Some of the reasons for the standstill in the mineral industry are partly economic, partly due to competing land use, uncertainty in applying or, recognising the principle of crown ownership of minerals, and to some extent lack of appreciation of two closely related exploration activities referred to as development exploration and assessment Exploration.

Jan 1, 1979

Coal exploration and mine planning now use all the modem techniques to indicate geological hazards to a new or developing coal mine. Drilling, seismic and other sophisticated geophysical methods aim to increase the reliability of prediction of features which will inhibit mine development. But do they?. During the past 40 years, geological investigations for coal mines in New South Wales have ranged from the general observations of Eric Rudd, in the Southern Coalfield in the late 1940s to the very detailed examinations of roof strata by John Shepherd and others in the 1980s. Then, the large scale regional relationships between sedimentary and structural features often were ignored as the minute examination of seam roof strata became fashionable.

Jan 1, 1991

By Sheridan GD

Fifteen samples 'of clays and shales from the Adelaide area were selected from a total of 84 as representing material of possible value for the manufacture of light-weight aggregate. A detailed examination of the bloating. characteristics of these revealed four likely to be suitable. for expansion.' in a rotary kiln. One of these, a Tapley. Hill shale., was-fired in an 8 in. diameter rotary kiln, but con-tinuous bloating without ring formation in the kiln was not achieved. Steam,,-oxygen,, sulphur dioxide and carbon dioxide have been, suggested. as the agents of bloating. An examina-tion of .. the evidence : `leads to the conclusion that carbon dioxide derived from. carbonate minerals is likely to be the principal bloating agent. Attempts to bloat clays by the addition of mica were.not successful.

Jan 1, 1963

By Sirayanone S, Rashad MZ

An important problem occurring in the iron and steel industry of Egypt is the presence of manganese oxide and chlorine with different percentages in the Bahariya Iron Ore Deposit, Western Desert, Egypt. In this work we used a geostatistical method known as the Volume- Variance Relationship to predict grade fluctua- tions of Fe% , Mn% and Cl% in the ore after blasting a certain volume from the ore deposit, on the other hand, if we have a certain limit for each of these chemical components, we can select the bench blasting dimension to give these limits.

Jan 1, 1986

By M Chappell

This paper describes the design of the steel fibre reinforced precast concrete (SFRC) segmental lining for the intake and discharge tunnels for the Gold Coast desalination plant in Queensland. In addition, the key design requirements and design methods for the lining of these 2 km long, 2.8 m internal diameter tunnels, including structural, durability and maintenance requirements are discussed. Details of the segment configuration and erection process are presented along with information on the manufacture and trial testing of the concrete for the segments. The paper also gives a brief introduction to steel fibre reinforced concrete behaviour. Construction of the tunnels commenced in April 2007, and the authors believe this is the first application of this technology in Australia.

Jan 1, 2008

One of the more recent developments within the mining industry has been the adoption of formal continuous improvement programs. A continuous improvement (CI) program was launched across Kalgoorlie Consolidated Gold Mines (KCGM) in early-2002. The purpose of this program was to identify further operating improvements within departments. The focus of the continuous improvement program was not only on the areas of the operation which were performing below expectations but also on areas of the operation which were performing well but could still be further improved.The effectiveness of a continuous improvement program depends on the stability of the processes in place and the participation of many employees from all levels of the business.Continuous improvement has had some successes and failures at KCGM and this paper will discuss both within the open pits department. Further improvements that could be made to the process will also be discussed. Kalgoorlie Consolidated Gold Mines Fimiston operation is located in the Kalgoorlie Goldfields and it the largest gold mine in Australia producing over 800 000 ounces of gold per annum.

Jan 1, 2004

By I P. W Chau

Construction of twin stacked railway tunnels through mixed ground conditions in the heavily populated urban environment of Hong Kong, including tunnelling in poor ground conditions, with low cover and under or adjacent to sensitive structures with minimal impact was the challenge presented by the tunnelling section of the Kowloon Southern Link project. This paper details how twin 1.1 km tunnels of 7.0 m internal diameter were driven by Mixshield tunnel boring machine (TBM) in mixed ground through one of the exclusive shopping and hotel districts in Kowloon. The paper addresses the challenges required to be considered and managed for the success of the project, including ground conditions, TBM selection, Mixshield TBM operation, settlement monitoring and control, ground- borne noise and vibration, proximity to utilities, buildings, roads and operating railways.

Jan 1, 2008