Search Documents

By C Hertle

GHD-Black & Veatch (GHD-BV) have completed design and specification of the ash thickening plant at Tarong Power Station, including operation of a pilot plant. Construction of the plant is in progress and commissioning is planned for early-2004. The objective of the new plant is to convert the low concentration (lean phase) ash slurry currently generated by the power station into concentrated slurry which will then be pumped to the existing ash dam. Water recovered from the lean slurry will be returned to the power station for reuse. The drivers behind this project are to extend the life of the ash dam and to reduce water pumping costs. A maximum flow of 1000 litres per second is expected in the thickening plant. The process involves a screening phase, which removes large material that could cause blockages or equipment damage. A 50 metre diameter thickener then concentrates the screened lean ash slurry to 55 - 60 per cent w/w solids. In addition, the thickener plant will allow the harvesting of floating cenospheres (hollow, spherical ash particles) from the lean slurry. Cenospheres are currently collected from the surface of the ash dam and drained on a pad adjacent to the dam. The new system will use a surface skimmer to remove the cenospheres from the thickener and transfer them to settling ponds for further classification. The settling ponds simulate the detention on the existing ash dam, and allow entrained fine ash and slow settling cenospheres time to settle. As settling occurs in ponds, the slow settling cenospheres can be completely recovered whereas when they settle in the dam, the opportunity for recovery is lost. Cenospheres are a valuable by-product produced during the combustion process, and recycling of this material reduces the waste generated by the power station. Water recovered from the thickener drains to a three megalitre reservoir. Water is drawn from the reservoir for thickener plant service water and various other uses in the power station. The bulk of the water is used to sluice ash from the power station to the thickening plant. In the current configuration, surface water from the ash dam is reused but must be pumped several kilometres back up to the power station. The dam also holds an inventory of several thousand megalitres of water and has significant evaporative losses. Therefore the current raw water make up demand is substantial. In addition, some areas of the power station traditionally using raw water will be modified as part of this project to allow the use of recovered water, further reducing the raw water demand. The design incorporates many features of sustainable water management. By more effectively recovering water from the lean ash slurry, the amount of raw water make up required by the system will be significantly reduced. This method of water recovery provides a more sustainable and energy efficient ash-transport mechanism.

Jan 1, 2003

The West Fork project is located in Reynolds County, Missouri, in the mineralized zone referred to as the Viburnum Trend. The West Fork orebody has a calculated ore re- serve of 13 600 000 tonne (15 000 000 st) con- taining 5.5 per cent lead, 1.2 per cent zinc, and recoverable values of copper and silver. A total of 64 600 tonne (71 200 st) of lead concentrate and 11 300 tonne (12 500 st) of zinc concentrate will be produced annually. The mill was designed to operate at an average capacity of 3450 tonne/day (3800 st/day), based on a 95 per cent availability factor. The mill will operate 24 hours a day, 5 days a week, with maintenance performed, as needed, on weekends. The mine will operate on an identical schedule; but the underground, pri- mary crushing will operate on a six hour/shift, three shift/day schedule. The 1.07m x 1.22m (42in x 48in) jaw crusher will produce a minus 20cm (8 in) material at an average rate of 191 tonne/h (211 st/h). The jaw crusher has almost twice the throughput capacity required, but the decision to install that size of crusher was based on the need to handle over sized rock in the ore.The coarse crushed ore will discharge into a 180 tonne (200 st) skip pocket, which will allow up to a one hour surge capacity prior to hoisting. Hoisted ore will discharge into a 900 tonne (1000 st) storage bin located adjacent to the headframe. The skip pocket and coarse ore silo comprise the total ore storage capacity. The concept of having no intermediate fine ore storage between the secondary crushing and grinding sections was borrowed from the Brushy Creek Mill of St. Joe Minerals, which operates adjacent to the West Fork property. Integration of the secondary crushing and grinding circuits has worked ' successfully for years at the Brushy Creek Mill. The most obvious advantage to eliminating the intermediate fine ore storage is'capital expen- diture savings. The capital expenditure savings include the cost of silos, feeders, and the cost of additional conveyor length and eleva- tion. Savings in operating costs will also be gained, particularly in reduced maintenance costs. Other factors which influenced the decision to eliminate fine ore storage were the simplicity of the secondary crushing sec- tion and the limited area available for con struction of the facility

Jan 1, 1978

The Australian mining industry is at an interesting stage in its development. Of the large number of mining companies in Australia, some are still solely domestic in their focus. others have made their first tentative forays offshore, and others are global players of significance in the world industry. It is not long ago that the entire industry was almost exclusively domestic in its focus. Very few companies before the early 1980s had ventured offshore, and those that did so were considered quite risque. The initial moves were made mainly by large companies who could afford to lose the funds expended in getting started in a range of offshore locations.

Jan 1, 1995

By Buizen M, Eagleton A. C

The results of calibration trials conducted on parachute stoppings both overseas and in Australia under a recently completed NERD&DC grant, are presented. Applications of parachute stoppings, for rapid regulation and control of ventilation networks are described including use in blasting areas and rescue work. Several parachute-type stoppings are described and their applications Investigated

Jan 1, 1988

By J Rutter, M NoppT

Ridgeway Gold Mine is part of Cadia Valley Operations which is wholly owned and managed by Newcrest Mining Limited. Ridgeway is an underground sublevel cave (SLC) operation mining approximately 5.6 Mt of gold-copper ore per annum. Ore tracking and accounting systems monitor gold and copper grades, copper mineralogy, host lithology and ore sizing. These factors have material impacts on concentrator throughput and metal recovery. Drawpoint recovered grades are routinely reconciled back to design data to monitor and assess draw performance. Grade control at Ridgeway has been based upon sampling the ore from SLC drawpoint bunds using 15 kg grab samples combined to form 30 kg samples prior to assay. This large sample size was selected in an attempt to representatively sample the coarsely-sized broken ore, the samples collected having a nominal diameter of about 130 mm. The assay results for gold and copper from these samples are extremely variable and the usefulness of the results has been questioned by the mine, particularly given the onerous and OH&S hazardous activity of handling large sample masses. Granulometry testwork at Ridgeway confirmed the extent of the relationship of decreasing sample grade variability with particle size. Based on this relationship, drawpoint sampling tests were carried out using 9 kg samples sieved to -45 mm at the drawpoint site. The gold and copper results from the finer 9 kg samples were significantly less variable than those from the normal, coarser 30 kg samples. The variance reduction was similar to that predicted from broken ore sample theory for the selected sample mass and nominal particle size. This relationship therefore allowed Ridgeway to assess the sample mass and particle size required to achieve a particular precision. In addition to improving the precision, the reliability of assay results from smaller samples from the fine particle fraction for drawpoint control depends on the accuracy of the results. The assumption is that the grade of the finer ore is similar to that expected from the lot, or that if a bias exists, then the extent of this bias is acceptable and consistent enough to be accounted for in the grade control system. The distribution of grade with particle size and the reconciliation of drawpoint sample and mine results is currently under investigation.

Jan 1, 2005

Natural leaching of minerals has been recorded for some two millenia but surprisingly only in recent years has enough been known of the process for any serious design to be made. Copper has been recovered from natural mine waters since about the 17th century but again little progress was made in de- sign procedures until recently. Natural or dump leaching was started as a recovery process late in the 19th century and in the years up to the classic study of Taylor and Whelan in 1943 a series of impirical optimis- ations made it a valuable process for treating low grade or waste material. The biological nature of Sulphide leaching was proven by Colmer and Hinkle in 1947 and since then a large mass of data has accumulated on the microbiology, biochemistry, and response of ores to this form of attack. In spite of this knowledge and the vast amount of pract- ical experience available there are few recorded attempts to present methods of calculation or design procedures that can be used for setting up a leaching process. A framework is given here on which such procedures can be based and indications given of the inherent advantages and limitations of the process,

Jan 1, 1969

By Browning E. J

The application of conventional dust control systems in British Coal mines has considerably reduced the incidence of pneumoconiosis. A number of new techniques have been developed involving extraction close to the cutting heads of mining machines which will be capable of controlling airborne dust with the greater intensity of production necessary in the present economic climate.

Jan 1, 1988

The Transportable Moisture Limits, as ,measured by the procedures laid down in The IMCO Code of Safe Practices for Bulk Cargoes, determine the target moisture contents for the concentrates produced at the West Coast Mines of Electrolytic Zinc Company of Australasia Limited at Rosebery. Filtration of these concentrates gives moisture contents considered to be low in comparison with those achieved for similar sulphide concentrates, but which are very close to these Transportable Moisture Limits. The filtering techniques used are outlined and the problems associated with-maintaining concentrate moistures below the required limits, together with the methods used to solve these problems are discussed.

Jan 1, 1978

By Steinbrucker G

Improvements in mining by the application of electronics necessitates analy-sis of the objectives and problems. A detailed analysis has shown that increased tunel-ling performance is one of the most important objectives. In mining, the environmental conditions for machines, their handling and servicing are very hard. Therefore a health monitoring system for tunnelling machines in hazardous areas has been developed. This system measures operational parameters, such as-flow, pressure, temperature, etc., de-rives forecasts of possible failures from these values, and assists maintenance person-nel. Important data are transmitted to a surface computer via telephone cables. Health monitoring is based on the cognition that slow deterioration of characteristic parame-ters, e.g. fluid loss, are symptoms of wear. Sudden changes of machine parameters indi-cate sudden destruction. Computer technology is very advanced, but transducer technolo-gy has not,been able to keep pace. Filling the yawning gap in the mining industry is a challenge to technology and requires special techniques. Machine monitoring and automa-tion in underground mining is still in its infancy. A lqt of development and research work is still necessary. The risks are great-The expected benefit due to increased min-ing performance (up to 5 %) justifies the risks in development.

Jan 1, 1985

By Ranklin W. J, Swinbourne D. R

Lead blast furnace slags contain typically 10 - 20 mass per cent Zn. The zinc can be recovered by slag fuming, in which a powdered coal/air mixture is injected into a molten slag bath. Volatilised zinc is recovered as zinc oxide from the gas and processed hydrometallurgically to produce zinc metal. The ISASMELT continuous lead smelting process in operation at Mt Isa produces a slag containing about 12 per cent Zn which is currently granulated and stockpiled. This slag could flow to a further bath-smelting reactor for continuous zinc fuming. Rather than collecting the zinc as fume from such a process, one option would be to recover it using a lead splash condenser. The success of this operation would depend on the composition of the gas produced, in particular the concentrations of gases capable of reoxidising zinc vapour, viz, carbon dioxide and water vapour. The aim of this investigation was to determine the smelting conditions for a bath-smelting process such as ISASMELT or SIROSMELT which would produce a gas similar in composition to that from an Imperial Smelting Furnace by thermodynamic modelling of the process using the CSIRO Thermochemistry System. It was found that such a gas could be produced if coal injection and oxygen enrichment of the combustion air to at least 40 per cent 02 were used. However, the off-take gases must be conditioned by addition of methane to reduce the water vapour content to acceptable levels. An addition rate of ten per cent of the off-gas flowrate was found to be adequate. Addition of methane to the off-gas had the added advantage of cooling the gas from the bath temperature to a temperature suitable for normal lead splash condenser operation.

Jan 1, 1993

By Tuite M. J, Woolcock L. J

The Awak Mas gold project is located in the Province of South Sulawesi, Republic of Indonesia. It is situated 300 km by road north of the provincial capital of Ujung Pandang. The capital is readily accessible by air from Australia via Denpasar on Bali or the Indonesian capital, Jakarta (Figure 1). Elevations at Awak Mas range from 850 to 1400 metres above sea level in reasonably rugged terrain. The area is covered by primary and secondary (regrowth) rain forest. The region is subject to an equatorial-type tropical climate. The annual rainfall is a high 3000 mm most of which falls in the rainy season between March and June. In the lower valleys rice, cloves and chocolate crops are cultivated. Title to the project area is secured by a Contract of Work (COW) issued to PT Masmindo Eka Sakti (MES) on 23 October 1987 by the Government of Indonesia. MES was controlled at the time by New Hope Industries group of Brisbane. After New Hope had completed initial reconnaissance exploration of the area, Battle Mountain Gold Company (BMGC) farmed-in in 1991 and earned a 60 per cent beneficial interest in MES.

Jan 1, 1996

With mining development on hold and other underground works in a slowdown, the development of nuclear wa te repositories takes centre tage on the American rock engineering scene. Three repositorie for commercial spent fuel-in salt, tuff, and basalt-are in the phase of site characterisation and conceptual design, and one pilot project for defense high-level wa te in salt is under construction. A repository design for crystal line rock has recently been postponed.Because of strict quality assurance requirements throughout design and construction, and because of the need to predict and ascertain in advance the satisfactory performance of the underground openings, much intellectual energy has been expended to analyse underground openings in the unusual circumstances of the repository environment. In the long term, these efforts will lead to an improved understanding of rock behaviour and improved methods of underground analysis and design. For the shorter term, a formalised ground control plan was developed, the principles of which may be applied to other types of projects.This paper summarises the status of underground design and construction for nuclear waste repositories and presents some details of the ground control plan and its individual elements.

Jan 1, 1988

By Singer RP

The Latrobe Valley brown coal deposits are one of Australia's major energy resources with measured and indicated reserves amounting to some 162 billion tonnes. Economically recoverable reserves are estimated at some 65 billion tonnes, 47 billion tonnes of which are classified as available for mining (VBCC (1983)). These deposits contain one of the lowest grade fuels used anywhere in the world. Typical Net Wet Specific Energy values range from 6 to 9 MJ/kg. Despite the low energy value of the raw coal, the Latrobe Valley deposits represent approximately 90% of Victoria's indigenous non-renewable energy resources. Utilisation of this vast primary energy resource has been a key factor in the economic development of Victoria.

Jan 1, 1990

Large Off Highway Trucks operated in this country are generally of Diesel Electric Drive, this system tends to employ the familiar Electric Wheel. A number of fleets now employ the Traction Motor System as an alternative. An investigation is made of the operation of two such fleets. A brief description is given defining the components and their basic functions in each system. Available life history is presented and system reliability, maintainability and operator reaction is examined. Trlmnnnr rpm rn~r In the past large Off Highway Trucks operated in this country, that is those greater than say 120 tons, have tended to be driven by a Diesel Electric traction system. Although manufacturers are now offering mechanical or mechanical/hydraulic drives in the larger machines comments will be restricted to examining the Diesel Electric System. Since commencing operations in the mid 1960 period Hamersley Iron has made use of the diesel electric drive system using the familiar Electric Wheel. A departure was made at Tom Price with the purchase of the Wabco 3200 Series Trucks. These 235 ton capacity units employed a dual rear axle system with externally mounted motors. In 1976 a

Jan 1, 1982

By Doig ID, Phillips HR

As a prelude to studying the sorption desorption and permeability behaviour of coal cores in a triaxial stressing rig using sorb- able gases, the air permeability of typical cores was measured. Lump coal samples were obtained from three gas-troubled collieries in Queensland and New South Wales. These were cored in the laboratory and a simple laboratory permeameter employed which accepted 38 x 40 mm cores in a thick rubber sheath. Air pressure of 500 kPa was applied outside the sheath to provide suitable sealing between the rubber and the coal. Differential driving pressures up to 100 kPa were employed and the air flow measured by displacement of water columns in inverted graduated cylinders. Flow measurements accurate to + 2% could thereby be achieved. Coal lumps were cored both parallel and perpen- dicular to the bedding plane, and were observed prior to measurement for any notable features, in particular for the presence of fissures. Between samples an overall variation of from 100 milliDarcy was found in Appin, Westcliff and Leichhardt coals. Significant variation was observed both from section to section of a core and between regions of a

Jan 1, 1982

By J Gutzmer

The Kalahari Manganese Deposit in South Africa accounts for 80 per cent of the worldÆs land-based mineable Mn reserves. Although the ores are primarily mined for export, South Africa is the worldÆs third largest producer of ferromanganese and ferrosilicomanganese alloy, both of which are derived from the smelting of these ores. Mineralogical analysis has traditionally been forsaken for bulk chemical assaying in quality control of smelter feeds, principally because quantitative data could not be easily produced. Yet, mineralogy plays a vital role in determining smelting behaviour, which in turn has economic implications when aspects such as energy and reductant consumption are considered. Smelting is an endothermic process, and the amount of energy input required is dependent on the minerals present in the ore, as well as their relative proportions. Further, knowing the bulk Mn oxidation state in the ores allows for calculation of the amount of oxygen that must be driven off to produce alloy, and hence the amount of reductant required. Additionally, certain minerals can be correlated with potentially deleterious elements, so that ore mineralogy can indicate penalty element distribution. Mineral abundance analysis was conducted on ores from the Kalahari Manganese Deposit using quantitative X-ray powder diffraction. Rietveld refinement using a fundamental parameters approach was applied to micronised ore samples. The mineral percentages obtained were validated using mineral chemical data together with bulk major element data derived from ICP-OES. Bulk oxidation state partitioning was then carried out knowing the Mn valence in the minerals. The results show potential for implementation of the proposed method on a smelting plant, where ore blending could be then implemented to achieve consistent feed compositions to smelters. Selective mining could also be undertaken to obtain desirable ore compositions for domestic or international markets.

Jan 1, 2008

A biological column leach testwork program was undertaken on a chalcocite ore. Three tests were conducted in all, using 65 in x 100 mm columns in three sections. The tests were started with varying acid strengths and inoculated with bacterial solutions from previous column testwork. The leaching of Cu was found to occur in three stages. These stages consisted of direct acid leaching, bacterial oxidation and ferric iron leaching. These leaching stages can most easily he described through the examination of not only Cu dissolution but also Fe dissolution and its subsequent oxidation and precipitation. The p11 of the system was found to he critical in establishing and maintaining the bacterial leaching system. The oxidation potential was seen to he influenced by the leaching system as the oxidation states altered. Test variables such as, 02, COz, and temperature were all found to influence the system. Final copper recoveries were in excess of 90 per cent in each column test over a leach time ranging from 211 to 328 days. Given similar leach conditions are applied, the application of this technology to site is expected to give comparable results.

Jan 1, 1994

By Rose CW

Typical rehabilitation programmes for spoil piles and waste dumps in open cut coal mines involve the spreading of topsoil to assist vegetation growth. In the early years of rehabilitation before a protective vegetation cover has been established, this topsoil is susceptible to erosion during rainfall events. Since the long term success of rehabil- itation procedures is sensitive to adequate topsoil maintenance and since, on many mine sites, topsoil is a scarce resource, erosion losses of topsoil (particularly once fert- ilised) can severely restrict rehabilitation Measures.

Jan 1, 1983

By Sandenbergh RF

The debate on the mechanism of adsorption of gold and silver di-cyanide onto activated carbon could be divided into two schools of thought. On the one hand, it has been proposed that the combined effects of electrostatic and chemical interaction between the activated carbon surface and adsorbing gold di-cyanide anion results in the adsorption of the latter. On the other hand the `ion-pair' adsorption reaction mechanism has been vigorously advocated as the dominant mechanism responsible for the adsorption of gold di-cyanide onto activated carbon. It is maintained that gold is adsorbed onto the carbon surface as the neutral ion-pair [M"+][Au(CN)z ]". Adsorption is viewed as the result of mainly the chemical interaction while electrostatic interactions are neglected. The validity of the `ion-pair' adsorption mechanism may be challenged on a number of counts. However, the alternative mechanism (based on aqueous surface chemistry principles) has not gained general acceptance yet, because it has not been applied widely enough to explain the different adsorption phenomena associated with gold di-cyanide on activated carbon. In the present study the case in favour of an adsorption mechanism based on general aqueous surface chemistry principles is presented. A model framework is developed for the adsorption reaction mechanism of gold di-cyanide onto activated carbon which incorporates the effects of chemical and electrostatic interactions between the dissolved species, the aqueous solution and the carbon surface. This model is then employed to explain a wide variety of reported adsorption phenomena for gold di-cyanide on activated carbon, such as the effects of pH, the adsorption of different metal cyano complexes, ionic strength, and type and concentration of cations in solution. In addition the effects of cyanide and dissolved oxygen concentration were investigated. No ready explanation, in terms of aqueous surface chemistry principles, is yet available for the switch in adsorption behaviour that agrees with ion exchange to ion-pair adsorption with increasing ionic strength.

Jan 1, 1997

By Wright S, Rogers L. J, Precious T. H

Brown coal and its char were investigated as substitutes for petroleum coke in the manufacture of anodes for Hall-Heroult cells. The char, which had been densified by several techniques, was made into compacts with various binders and the anodic consumption determined during electrolysis. The results were an improvement on previous work, but the anodes still fell short of acceptability for use in aluminium smelters because of intractable microporosity. Some options for future development have been discounted.

Jan 1, 1986