Search Documents

Nickel laterite approximately 40% of the remainder caning deposits. ores are the source of the world's nickel with from sulphide ore Although laterite ores are near the surface and cheap to mine they require significantly more energy to treat than sulphide ores. The escalation of oil prices comiencing in 1973 meant that nickel laterite refineries using oil as an energy source were placed at distinct disadvantage relative to sulphide refineries or those with coal derived energy. The Queensland Nickel refinery commenced a construction programme; in 1980 to allow ore drying and power generation to be converted from oil to coal. Since late 1981 ore drying has been undertaken using heated air from two moving grate spreader grate stokers. The changeover from oil to coal drying proceeded without process disruptions. This paper discusses the plant changes required to allow the receipt of coal and the operating performance obtained from the coal fired air heaters.

Jan 1, 1987

By K Knorr

Desktop X-ray powder diffraction using a D2 PHASER equipped with fast linear detector was performed on several iron ore and mill scale samples. Data were analysed using cluster analysis and Rietveld quantitative phase analysis. The quantitative mineralogy of both materials could be established. Thus the input is provided for understanding the energy consumption and the CO2 emission during iron production. Furthermore, tabletop XRD allows to distinguish iron ore from mill scales and to quantify their mixtures.

Jul 11, 2011

When Matthew Flinders entered in his log `This land forms the South side of the large bight; and besides projecting beyond the coast line, and being a little higher than usual is remarkable for having some reddish cliffs in it, and deep water near the shore', he was commenting on the deposit of bauxite at a place now known as Weipa. This sighting took place on 9 November 1802, and probably represents the first direct entry in Australia acknowledging a potential mineral deposit. Flinders, of course, had no idea as to what he was looking at, nor did he land to determine its content. If he had, he probably would have had no idea of the substance, and even less knowledge of its use. Nothing further was done to this for about 150 years.

Jan 1, 1993

The increasing introduction of high capacity mechanical equipment into the coal mines of New South Wales following. tforld War II brought with it problems of roof support. Rapidly advancing headings in difficult country could not be supported with heavy, close,timbering due to the time involved in installation and the reduction of available' space for the movement of machines. _ The installation of low cost, space saving, rapidly installed roof supports became a necessity if the new mechanical equipment wa-s to be allowed to operate at maximum efficiency. As, a result of experience in the United States of America, the system of roof support using steel reinforcing bolts began to find increasing, popularity in the mechanised mines in this State. From the somewhat'crude methods of in- stallation adopted in some of the, early trials, the practice of roof bolting has advanced into a-highly technical operation, requiring care and skill to ensure optimum results.

Jan 1, 1971

By P McGavin, R von Varendorff

With the economic trend towards reduced capital spend, more stakeholders are focusing on improved operational efficiency and productivity. Advancements in achieving the optimum dollar-per-tonnage will be more dependent on creating a logistics system that is well balanced and economically optimised. Critical to predicting a successful business case is the ability to accurately define capacity, realistically increase throughput and proactively translate objectives into design and operating requirements. Failure to do this will create an unrealistic perception of capacity and performance for the export corridor. This transition requires a fundamental understanding of the drivers that impact capacity, cost and value across the entire logistics chain. Through examples, this paper will identify the contextual requirements for simulation models that assist decision-makers and stakeholders to more clearly understand the implications of decisions that will define capacity and operational performance. The aim of this approach is to provide a rigorous analysis of the outcomes - regardless of whether the export corridor is owned, used and operated by one entity or various companies.CITATION:von Varendorff, R and McGavin, P, 2013. Can we live up to the capacity expectations weÆre predicting for our iron ore export corridors?, in Proceedings Iron Ore 2013 , pp 553-560 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

THIS paper is not intended to be more than a mere outline of the economic geology of Tasmania. It is desired to present in a condensed form the present state of our knowledge in regard to the distribution of the ore, coal, and oil-shale deposits of Tasmania in time and space.Tasmania is exceptionally well endowed with mineral wealth, particularly in the north-western and western districts. In the enthusiasm resulting from the first discoveries of mineral deposits at a great number of localities in those districts, it became a generally accepted belief that the whole of that portion of Tasmania constituted a continuous metalliferous province. As geological research in these, areas has progressed, however, it has become increasingly clear that ore-deposition has been confined on an economic scale to definite well-defined areas or belts which have a genetic relationship to certain tectonic and petrologic phases of the general geology. These areas or belts have recently been defined by the writer, and...

Jan 1, 1923

By Brechtel C. E

Providing adequate airflow to effectively dilute and remove diesel pollutants in large mine working headings is a little researched area. A simulated diesel mucking operation was carried out in the Exxon Colony Pilot Mine in Colorado to establish expected levels of diesel pollutants in dead-ended working headings. This heading was nominally 15.3 m (50-ft) wide by 9.2 m (30-ft) high. Two face ventilation systems were tested using sulfur hexafluoride tracer gas to represent the diesel pollutants. The results of these tests showed that conventional face ventilation systems operating at high flow rates could adequately ventilate diesel equipment in the 447-522 kW (600-700 hp) range, even in a dead heading 91.4 m (300 ft) in length.

Jan 1, 1988

By S Planeta

The use of explosives in underground mining has its drawbacks, particularly in the case of thin or narrow vein type deposits. Due to that, there is a need to develop more discriminative and safe rock-breaking technologies. Mechanical rock splitting seems to be one of the most promising avenues in this respect. This paper describes briefly principles and features of radial-axial splitters. It reviews a feasibility study done to evaluate a potential of this technology in selective mining. It was intended to compare productivity and cost of ædrill-splitÆ mining with conventional cut-and-fill method. Hypotheses and assumptions adopted, methodology used and the obtained results are presented and discussed. The study has confirmed an interesting potential of radial-axial splitters in mining thin and narrow vein deposits. In conclusion, it is stressed however, that it will take more R&D work to corroborate the results obtained. Some suggestions concerning future research in this field are also given.

Jan 1, 2003

By Fink ST

Management requires up-to-date information on the activities of an enterprise in order to maintain control and to assist in decision-making and planning. In today's environment it is essential that this information is immediately available and in an easily assimilated format. If this is not the case, management is forced to make decisions based on intuition and past experience. At Mt Newman Mining Co, a computer application has been developed and implemented with the objective of providing this type of information to management. The Key Parameter Reporting System (as the application is known) allows for daily (constant) on-line capture of selected production statistics, safety statistics and free format textual comments relating to topics such as industrial relations, major maintenance and other pertinent news. Information can be retrieved,'and displayed or printed in either a tabular or graphical format. All senior managers have colour visual display units in their offices for immediate access to the system. Access to selected sensitive information is controlled. All company staff are able to retrieve unsecured information from the system via visual display units installed in all company Locations.

Jan 1, 1983

By Trudinger JP

Mt. Newman Mining Company Pty. Ltd.3 oper ates the Mt. Whaleback iron ore mine in the Ham- ersley Iron Ore Province of Western Australia. The present rate of production of high grade hematite iron ore is 33 million tonnes per year. Mining is by open cut quarrying,with 15m high benches. The present quarry operations will be extended to a large oval pit to win over 1400 million tonnes of iron ore. The pit slopes will extend up to 500m in depth and the perimet- er of the slopes will exceed 15km. Sixty per- cent of the ore is below the water table, which presently lies 45m below the general plain level Dames & Moore, rock mechanics consultants designed the pit slopes during early mine devel- opment to ensure an economic and safe operation.

Jan 1, 1975

Metsim is proving to be a powerful tool when designing a heap leach operation. The most useful outputs arc determining the fluctuations in pregnant solution recovery rate, make-up water rate, gold recovery rate. and pond levels. Detailed data are needed for input: a pad loading schedule, a mining rate schedule for each ore type, column leach test data for each ore type, column tests on water dynamics (ie hourly flow-out versus-in during saturation and drain-down), monthly rainfall and evaporation data, and proposed pond dimensions. These data allow 'what if' studies on application rates, leach rates, loading rates and other variables of interest. Examples will he given of modelling both a rectangular pad and a valley fill operation.

Jan 1, 1994

The Escondida Porphyry Copper Deposit, located in Chile's II Region 160 Km to the southeast of the city of Antofagasta, is currently owned by Minera Escondida Limitada, a company comprising The Broken Hill Proprietary (57.5%), Rio Tinto Zinc (30%) a group of Japanese companies represented by Mitsubishi Corporation (10%), and the International Financing Corporation of the World Bank (2.5%) (Fig.l)By 1983, most of the reconnaissance drilling was completed and prefeasibility studies were regularly updated as new drilling results were reported and project concepts re-evaluated (Fig.2). In October 1982 the project was transferred from Exploration Management to Operations. By the end of 1984 project pre-development activities, including inpit development drilling, geological exploration, water resource definition, an underground bulk sampling program and the initial project feasibility report, were completed.

Jan 1, 1990

By Patridge A. C

Hydrocyclones have widespread use as classifiers in applications such as mine fill preparation and coal preparation. A fundamental conflict often exists between recovery of all of the valuable material and maintaining the quality of the product. This conflict is a result of a portion of the feed material passing through the cyclone, effectively without undergoing any classification. This paper describes an investigation, undertaken as an undergraduate project in mining engineering at the University of NSW (Brook, 1994), into aspects of cyclones in which supplementary water injection is used in an attempt to reduce the amount of misplaced fine material reporting to the coarse product and hence improve the overall classification efficiency. In particular, the study concentrated on the effects of different modes of water injection. Two methods of introducing wash water into the cyclone body were investigated. A series of tests were performed on a laboratory hydrocyclone having provision for radial water injection at different levels through small orifices in the wall of the conical section, and a preliminary study was made of the performance of a novel cyclone in which the conical section had walls of a permeable polyethylene, permitting a uniform introduction of wash water over the entire surface.

Jan 1, 1995

The evolution of the Oaky Creek mining complex provides a good example of the mining cycle in practice. Oaky Creek has been innovative in its choice of mining methods, with virtually the full range of coal mining methods having been used as workings have progressed down dip. The history of the mine is traced through its development (and ownership changes), progressive selection of mining methods as depths of cover to seams being mined have increased, and rehabilitation. This allows the different mining methods to be described and illustrates the concept of æwall-to-wall miningÆ.

Jan 1, 1998

The original design of the Bougainville Copper Limited (BCL) concentrator took cognisance of the constraints imposed by the topography, the need to minimise capital cost, and the need to allow for plant expansion which, it was known, would be necessary to maintain copper and gold production as head grades declined.At the same time as spare slots have been taken up with additional equipment, technological innovations have been embraced whenever there appeared to be a chance of improving the productivity ofexisting equipment, or replacing it with a more efficient alternative.There are many examples of this in the BCL concentrator in the areas of process control, process design, instrumentation, materials handling, equipment design and wear part technology.Current process developments also pursue the latest technology. The development of the Omnicone crusher, flotation control, tailings water reclamation, and the variable speed gearless drive on the No. 13 mill are prime examples.

Jan 1, 1986

By Mozley R

Contaminated sediments are a multinational problem. A crucial factor in solving an environmental problem is knowledge of, not only the amounts of polluted soil, the contaminants involved and their concentration, but also the historical background of the problem. Processing polluted soil is a tailor made activity based on rational decisions resulting from a detailed treatability study. Lack of information about characteristic properties of a specific sludge/pollution combination is the main obstacle in the route from first ascertaining that a particular harbour subsoil is polluted, to final identification of the full scale treatment plant. In the first instance, information must be generated regarding the distribution of pollutants in relation to the distribution of the original geophysical components. Based on this information rational decisions can be made on separation at a particular cutpoint and what sequential techniques should be involved for a certain fraction. For this purpose a `fingerprint method' is presented especially developed for investigation of polluted soil and sediments. The heart of the fingerprint method is a series of sequential hydrocyclone separations, by which a series of products is generated. The objective of the fingerprint method is to select an optimised treatment procedure in which the pollutants are concentrated in as small a volume of material as possible, leaving the bulk of the material clean. The pollutants can then readily be destroyed or isolated from the environment. The philosophy and advantages of the fingerprint method are demonstrated for a harbour sludge containing heavy metals as main pollutants. Hydrocyclone separation combined with flotation of both the coarse and fine fraction resulted in reusable and dischargeable products. Flotation of the fraction of fines was carried out by means of an experimental flotation cyclone enabling the selective recovery of mineral particles with diameters less than 10 microns. The overall conclusion is that design and engineering of treatment flow schemes for polluted dredged materials is a tailor made activity based on rational decisions resulting from the fingerprint information.

Jan 1, 1993

By Chitombo GP

The proposed guidelines on vibration limits that have been circulated by the Australian Environmental Council, demonstrate the need for an extensive data collection and evaluation program to avoid the enacting of abritrary and costly legislation. The operational or practical influence of blast design and overall economic implications of legislation which further reduces permissible levels of ground vibration are discussed. In a typical blasting operation, blast sizes could become smaller and blasting correspondingly more frequent to meet pro- duction demands. Blasthole diameters and charge lengths could be reduced, increasing drilling costs and associated labour costs. Blast size however, is frequently controlled by factors associated with machinery, grade control, pit control, stope size, production contract levels and other factors which cannot be readily changed for operating mines. Blasthole diameters are frequently deter- mined by existing drilling equipment, length of holes (depth of ore or stope size), geological structure and other factors which are not easily changeable. Typical large scale open stoping and strip mining opera- tions are analysed as case studies. The effects of extreme leg- islative limits and the corresponding operational changes with respect to variations in production costs are discussed.

Jan 1, 1987

By I F. Wood

Planning for flooding and assessment of flood impacts are important requirements for mining projects, as they are also for other types of development. With more intense development and concern from the community, supported by government regulatory requirements, assessment of flood concerns and impacts has become of increasing importance. To ensure that flooding issues are fully understood and results presented in an appropriate format, advanced hydraulic analysis procedures have been developed and are beginning to be applied. These procedures must be rigorous in an engineering context but the results must also be readily understood by the community and government agencies. Advanced two-dimensional hydraulic modelling is becoming accepted as an important means of assessing flooding issues for mining projects. With presentation of results from hydraulic models with Geographic Information Systems (GIS), flood impacts can be analysed rigorously and presented clearly. This paper discusses the application of advanced hydraulic modelling in the planning and impact assessment of a major mining project located on a floodplain where there is extensive inundation. The analysis provides for both input to the planning of the project and for detailed assessment of potential impacts. This case study illustrates some important aspects of the application of hydraulic modelling using a two-dimensional modelling to a critical flood design.

Jan 1, 2003

By N McKenzie, F Brodbeck

The North-South Bypass Tunnel is the first project to get underway as part of BrisbaneÆs transport plan, which aims to improve the urban road network. The total length to be excavated is 6.8 km, which includes 4.8 km of driven tunnel and associated road connections. Construction commenced in August 2006 with project completion targeted well before the contractual completion date of October 2010. Due to the local geology, in particular the hard Brisbane tuff and neranleigh-fernvale formation, a combination of tunnel excavation methods are used. The majority of the tunnel is excavated by two tunnel boring machines which have a rate of progress of 16 - 20 m per day in rock having a compressive strength of between 80 and 150 MPa. Ten roadheaders operate at a rate of up to 2 m per day excavating the remaining tunnels, such as ramps, access tunnels, cross passages and merges. The tunnel team are managing the challenges and complexities associated with tunnelling through the hard Brisbane rock. A major challenge arose during the planning of the initial mainline excavation underneath the Royal National Association Showground in Bowen Hills. This section contains low rock cover and historical maps indicate that the showground is located within a former topographic depression (alluvial valley), which a creek once flowed through.Due to traffic merge design requirements, both tunnel boring machine (TBM) and roadheader excavation methods were required to be used in this challenging geological profile. The answer was to stabilise the alluvium above both TBM section tunnels from the surface prior to excavation and to operate the TBM in single shield mode with immediate grouting of annular void from the tail shield. In addition, the roadheader section of tunnel required additional support by spiles and canopy tubes installed from the tunnel face.

Jan 1, 2008

The exploration and mining risks are investigated and compared to the risks of smelting, secondary processing and other normal industrial activities. This study concentrates on the risk before, or at the investment decision. Internal and external risks are distinguished. Internal risks are the risks inherent in every engineering design and common to all projects. The main external risks are the financial risk, changes in prices, location problems and geological factors. Financial risks concern every capital-intensive and export-oriented project and cannot be considered as typical mining risks. Changes in prices, i.e. the market risk, concern every industry using raw materials, but the market risk is especially accentuated in the mining industry. Problems of location and infrastructure are normally more significant in mining than in other projects, and geological risks are unique to mining. All these risks associated with mining projects combine to form a risk at least twice as high as that for other normal industrial activities. Within the range of profitability of mines, which on average is the same as in the manufacturing industry, only a few highly profitable mines exist. These few mines are the sole reward for the high risks taken.

Jan 1, 1986