Search Documents

By Heyer T, Wasmuth H-D

The concentrator plant of Fahrica Mine, that started production in 1977, was using nine Jones wet high intensity magnetic separators (WHIMS) of the standard type DP 317 with a 1.5 mm gap width for the production of pelletfeed concentrate. These WHIMS units were operating in parallel with a feed rate of 110 t per hour, with about 47 per cent Fe in the feed, and with a maximum of only 0.8 per cent magnetite. The field strength was about 1.2 Tesla. From 1986, the mine has adapted its production facilities to mine and concentrate larger amounts of lowgrade itabintes to maximise the use of the available iron ore reserves. An increase of up to three per cent magnetite in the magnetic separator feed, resulted in a reduction of capacity. This was due to partial clogging of the separation boxes at high field intensities, which were required for the recovery of the very fine hematite. Even by lowering the feed rate and the field intensity the problem could not be resolved. After extensive testwork in a pilot plant, with a Jones separator model DI' 90, the commercial WHIMS plant was modified into a two stage process using the existing nine Jones separators. The gap of the first stage with four machines was increased to a width of 3.5 mm, corresponding to a maximum field intensity of 0.7 Tesla. This first 'medium intensity scalping stage' is followed by a second 'real' high intensity WHIMS step with five machines operating at the original settings with 1.5 mm gap width and 1.0 Testa maximum field intensity. Feed rates of up to 320 tons per hour in the first and up to 240 tons per hour in the second stage could be achieved. The design concept of the concentrator at Fabrica mine is described using the old and new flowsheets. Details of the pilot plant testwork as well as actual performance data of the new plant section are presented.

Jan 1, 1993

By J Hadjigeorgiou

The stability of open stopes in underground hard rock mines is influenced by several factors including the shape and size of the excavation, surrounding stresses as well as the degree of jointing. This paper presents a design methodology for stope analysis in jointed rock masses. The proposed approach relies on geological structural data to construct realistic three-dimensional joint network models. The stability of an open stope is determined based on a limit equilibrium analysis.

Jan 1, 2000

The proximity of the Town of Kalgoorlie to the Mount Charlotte mine necessitates that charge weight per delay be limited in order to keep surface vibration levels within acceptable limits and to reduce damage to underground workings. The mining system requires that large mass blasts must be used to recover pillars and therefore a large number of separate delays are needed. Until recently all blasting has been done electrically, fired from mains, but with the introduction of large diameter blastholes (165mm diameter) this firing system was inadequate. Various firing systems were considered, but after extensive trials a non-electric sequential firing system was chosen. This system fulfilled all criteria of blast design, was relatively straight forward in charging technique and had a very simple primary initiation system. Although initially designed for large mass blasts, the non-electric firing system is now used for all large hole blasting and in a simpler form for small (57mn diameter) holes.

Jan 1, 1982

By Balint F

The Izok massive sulphide deposits are located in the Northwest Territories of the remote western Canadian Arctic. Together they represent one of the highest grade undeveloped zinc-copper resources in North America. Metall Mining Corporation is presently engaged in a feasibility study on developing the Izok property as well as actively exploring for additional reserves. The Izok deposits are Archean-aged, volcanogenic massive sulphide (VMS) bodies hosted within and near the top of a thick sequence of predominantly felsic pyroclastic rocks. The hangingwall package includes additional felsic volcanoclastics, dacitic and basaltic flows, thin sulphide-rich iron formations, and turbiditic sediments. The felsic volcanics are intruded by syn- to late-hydrothermal dacitic dykes and sills and post-hydrothermal gabbroic dykes and sills. Both intrusives are interpreted to be volcanic feeders to overlying flows. All lithologies are cut by much later irregular granitic pegmatite dykes and regionally metamorphosed to pyroxene homfels grade. The deposits occur within a large kilometre-scale soda-depleted alteration zone. The immediate footwall and hangingwall rocks to the deposits are characterised by zones of muscovite-biotite (with or without sillimanite), lesser chlorite-biotite-cordierite (with or without anthophyllite), and locally intense silicificified and albitised zones. All lithologies have been affected by a later calcic metasomatic alteration. As currently defined, the Izok Zn-Cu-Pb-Ag deposits comprise a cluster of four complexly-zoned composite lenses: the Northwest, North, Central, and newly discovered Inukshuk deposits. The first three deposits are amenable to open pit mining while development of the Inukshuk deposit will require underground methods. The combined mineral inventory of the Northwest, North, Central and Inukshuk deposits at present totals 15.6 million tonnes with a grade of 2.4 per cent Cu, 13.8 per cent Zn, 1.4 per cent Pb, and 74.6 g/t Ag.

Jan 1, 1993

By G M. Volkmann

Pipe umbrella systems have effectively been used as an additional support system in the working area in weak ground conditions during the last decades. Thus, a considerable number of applications accounts in urban tunnelling with shallow overburden. However, this support system is also successfully used when a tunnel alignment crosses fault zones, sediments, moraines or talus with overburdens from shallow to deep. The pipe umbrella support system itself is termed differently worldwide – synonyms are canopy tube umbrella method, umbrella arch method, or long fore-poling method.One main reason for the increase in application is that this support system closes cost-effectively the gap between reasonable, normal supported tunnels and tunnels supported with more expensive special techniques like horizontal jet-grouting or ground freezing. By using this system, many projects can be built more cost effective without decreasing the common level of safety.The pipe umbrella construction method is pretty young, so the knowledge about this system has been intensely researched in the last decade. This led to an enormous increase in understanding the interaction between support system and surrounding ground, the mode of action, and the important details for construction.Pipe umbrella support systems are applied in difficult ground conditions, so a special developed measurement arrangement was used to observe deformations ahead of the working face during tunnelling. The evaluation of collected data sets identifi ed that cased-drilling systems have clear advantages compared to predrilling systems during the installation process in weak ground conditions. This may become important depending on project requirements, so this difference must be considered in design as well as in the tender document specifications.

Mar 8, 2011

A major problem in the continuous casting of aluminium killed strip steel is the incidence of black and grey lines in the strip surface caused by the alumina inclusions. One place for limiting the number of alumina inclusions is by providing favourable fluid flow conditions in the ladle so that the inclusions float out to the surface or adhere to the ladle wall. In laboratory equipment 20 kg of steel was melted in an alumina crucible of 14 cm diameter in an induction furnace. Deoxidation was carried out while the melt was constantly stirred by argon bubbling. Bubble frequencies were measured at the lance tip using a microphone technique. High speed cine photo- graphy was incorporated to measure melt top surface velocities. Experimental results indicate that the rate of removal of inclusions is a function of both the gas input and the power input. However due to unfavourable surface area to volume ratio, reoxidation of the melt took place. Some other experimental difficulties in working at high temperatures are also discussed such as lance design, melting arrangement and sampling techniques.

Jan 1, 1984

By Wilson PH

A research programme sponsored through the Australian Mineral Industries Research Association investigated two aspects of mine aerodynamics on model scale. These were aero- dynamic losses in (a) shaft/airway intersections and (b) losses created by mine cages moving in a combined haulage/ventilation shaft. The shaft/airway intersections studied included base and intermediate levels for both upcast and downcast. shafts, with one to four rectangular airways intersecting a circular shaft. Changes in intersection geometry were limited to the installation of 45¦ conical brow cutoffs of varying size and the addition of simple flow control devices. The relative air- flows between the airways and the downstream shaft were varied over a range employed in Australian mining practice. In general, experiments revealed that a small brow cutoff was significantly better than none at all, and a simple device such as a cone can reduce losses and improve flow stability at an intersection. The mine cage studies determined the effect on aerodynamic loss of cage area blockage, height/length ratio, openings in cage walls and surface roughness due to external structural members. The results show that in a combined haul- age/ventilation shaft, when the relative air

Jan 1, 1978

This paper describes the operation involved in the sinking of a concrete-lined elliptical-shaped shaft at North Broken Hill Limited.Major factors such as geological features, future ventilation, ore haulage at depth and their relation to the location and selection of the type of shaft are described.Features covered in the sinking of the shaft include equipment details, with special reference to mechanical mucking, operational cycles based on time study analyses for sinking, concreting and the placing of steel sets. Safety precaution and statistical data is alsoincluded.INTRODUCTIONDue to the northerly pitch of the ore bodies in North Broken Hill Limited leases at approximately 42°, and the deepening of the active mining zone, it became apparent that No. 2 Shaft, the main operating shaft, would become unsuitable for the extraction of ore from the lower levels.Another major problem was the ventilation of the lower levels, and it was evident, that to ventilate efficiently these, and deeper levels, another upcast ventilation system would be required.Consideration was given therefore to the following: 1. Sink No. 2 Shaft from the existing bottom at 2770 ft. to 4200 ft., or Sink an internal shaft from the 2600 ft. level approximately 1000 ft. N. of No. 2 Shaft.2. Sink a new haulage and downcast shaft from the surface.3. Sink a new upcast ventilation shaft from the surface.It had been suspected that the ore bodies might flatten or even undergo a pitch reversal before reaching the...

Jan 1, 1956

This paper discusses design concepts in planning a large modern bulk terminal. The need is emphasised for a studied master plan, in-built materials handling flexibility and staged development. An integrated approach is advocated, combining functional purpose designed foundations and structures to serve their mechanical, electrical and environmental functions. Dry bulk and slurry handling are also compared in perspective.

Jan 1, 1983

By Sulanto J, Talonen T

In the mid 1960's Outokumpu considered building a lead Flash Smelter on the basis of Flash Smelting technology developed first in the late 1940s for smelting copper concentrates. Pilot scale tests were carried out and the process was found technically sound. The project was however not economically viable under Finnish conditions and it was cancelled. In 1981 pilot plant tests were restarted after many enquiries from the primary lead producers. All the know-how and development made in copper and nickel smelters was applied to the Lead Flash Smelting process and the tests were successful. Outokumpu has so far tested several types of lead concentrate with lead contents ranging from 28 to 75 per cent. The concentrate is oxidized and smelted to metallic lead and slag directly in the Flash Smelting Furnace using high oxygen enrichment of tonnage oxygen. Fossile fuel is used in the Flash Smelting Furnace in cases when the feed material does not contain enough latent heat to smelt the furnace products even though pure oxygen is used for oxidation. Thus the process results in a low consumption of extraneous energy. Use of oxygen results in a small gas flow but it is rich in sulphur dioxide. The gas treatment facilities and sulphur recovery plant will be small in size and low in investment cost. The process is flexible and can produce stable quality of products from different types of raw materials. Quality of lead bullion especially the sulphur content can be regulated over wide a range, from 0.1 per cent upwards according to the needs of the refinery.

Jan 1, 1984

By Hindmarsh G

The colliery is owned by the BHP Collieries Proprietary Ltd., the principal shareholders being the Broken Hill Pty. Company Ltd. and Hebburn Limited.It is situated due west of Newcastle and 6 south-east of Cessnock, N.S.W., and is conneeted by 36 miles of railway to the port of Neweastle. Of this mileage, 3 miles are owned by the Company, 3 by Hebburn Limited, 9 by the South Maitland Railways Ltd., and 21miles by the Government Railways.The seam worked is known as the Main Greta Seam of the Greta Coal Measures and is on the southern slope of the Lochinvar anticline.At the shaft, the seam is 1190 ft. below the surface, and the section of the coal measures is:-Upper or Main Seam, . 24 ft. 0 in.Conglomerate and shale 70 ft. 0 in.'Middle Seam 8 in.Conglomerate 25 ft. 0 in,Bottom Seam 1 ft. 2 in.These lie between two marine measures, and are the lower coal series of the permo-carboniferous period.Only the upper seam is workable in this area, the lower seams being too thin for eompetitive working. The section of the workable seam at the shafts is as shown on Fig. 1.Unfortunately, only the lower 12 ft. 5 in. of the seam is saleable.

Jan 1, 1935

By J E. Lynch

The Mt Leyshon gold deposit produced in excess of three million ounces of gold and considerable silver over a period of approximately 130 years. Most of this production occurred between 1987 and 2001. Mining commenced in 1872, however it was highly likely that Chinese miners were not only removing alluvial gold from the area but were also mining very rich æreefÆ gold. Records for early alluvial and hard rock mining do not exist, however gold production was probably considerable. In the early 1980s Marathon Petroleum (Australia) Ltd (MPAL) joint ventured into the Mt Leyshon area which had been held as a mining lease by Noranda Australia Ltd since 1968. Noranda at that time was concentrating its exploration effort on the Balcooma base metal prospect areas to the north of Charters Towers. In early 1982 MPALs parent company was taken over by US Steel. This led to an opportunity for MPALs Australian management to purchase all tenements and licences (except for coal, oil and gas) which were duly purchased for $US 1 million. At this time MPAL had a remarkable array of gold tenements (many of which were subsequently mined by other companies) and Mt Leyshon was considered to be the highlight. Early æseedÆ capital ($A 3.1 million) was raised with backers being the Bank of America, the NSW Government Superannuation Scheme, Westpac, private individuals and a Queensland grocery chain by the name of æJack the SlasherÆ.

Jan 1, 2004

By R C. Morris

The channel iron deposits (CID) (Ramanaidou, Horwitz and Morris, 1991; Morris, Ramanaidou and Horwitz, 1993; Ramanaidou, Morris and Horwitz, 2003; Morris and Ramanaidou, 2007) are one of the two major iron ore types mined in the Hamersley Province. The CID provided around 41 per cent of the total of 268 Mt of iron ore mined from the Hamersley Province in 2006. The current CID resource is around seven billion tonnes. The CID deposits occupy numerous meandering palaeochannels in a mature surface that includes Precambrian rocks and ferruginous palaeogene valley fill. These palaeochannels are generally less than a kilometre but can range to several kilometres in width and from one metre to more than 100 m thick. The two currently mined CID areas are located:in the western Hamersley Province in the Robe palaeochannel, and in the east in the Yandi palaeochannel. These two major CID channels extend over 100 km to 150 km, with the Robe system up to 5 km wide. The granular ore facies typically contains ooids and lesser pisoids with haematite nuclei and goethite cortices, with abundant goethitised wood/charcoal fragments and goethitic peloids, minor clay and generally minimal porous goethitic matrix. Post deposition weathering is common and produced secondary facies.Ooids and pisoids were mostly derived from the stripping of a well- vegetated deep ferruginous surface. The peloids were derived both intraformationally from fragmentation and reworking of desiccated goethite-rich mud. Minute wood/charcoal fragments in the soil that were initially replaced by goethite and then dehydrated to haematite, formed nuclei for many ooids and pisoids. In addition, abundant, generally small (in situ by goethite within the consolidating CID. This profusion of fossil wood, both as ooids and pisoids nuclei and as discrete fragments as well as the local presence of kenomagnetite suggests major episodic wild fires in heavily vegetated catchments. The goethitic matrix was the result of chemically precipitated iron hydroxyoxides, resulting from leaching of iron-rich soils in an organic environment.

Jan 1, 2007

An approximate rapid design system for tunnel liners and underground structures is presented which permits the effects of structure geometry and stiffness, rock quality in terms of its deformation modulus, and the applied system loading to be entered as data to produce direct designs conforming to stress limitations, optimum reinforcement requirements and restraints on section dimensions. An 'equivalent column' concept is introduced for modelling the rock mass in contact with the structure. Only the rock treatment is given in detail but the results of sensitivity analyses, with reference to rock quality, for a typical liner design are given and these results related to a number of empirical design approaches.

Jan 1, 1976

By Tomlinson E, Lama RD

Drainage of gas has been practiced overseas for almost half a century. Peal advances in drainage of gas to combat high emissions became practicable in the late fifties and early sixties when the technology was standardised to use it under a variety of mining and geological conditions. Today methane drainage is practiced in the United Kingdom, Germany, France, Belgium, Poland, Czechoslovakia, Hungary, Ibmania, U.S.S.R., China, Japan, Canada, U.S.A. and Mexico. Australia entered the list of countries using gas drainage on 3rd March, 1980 when the first full scale gas drainage system was set up and commissioned at West Cliff Colliery to drain gas from the Bulli Seam. Methods used in Europe are different from those used in North America, Japan and Australia mainly because of the different mining methods and also because of the limited number of seams under extraction, relatively new coal fields, and comparatively larger distance between the seams. In spite of the difference in the technique, the basic aim is the same and that is to improve ventilation and reduce ventilation costs, alleviate dangerous gas accummulation, overcome outburst hazards and ultimately make mining safer and more efficient. Over the last decade, there has

Jan 1, 1982

Through the stress synthesis of many exanples of macrostructure from eastern to western parts of China, it can be concluded that in Chinese tectonics there are two push- twisting forces, one of which ("Rl", from SE to NW) came from the Pacific Ocean plate thrusting over the Chinese continent plate in the eastern part of China; the other ("R2", from SW to NE) resulted from the thrusting of the India plate. The meeting line could be situated along the belt from 104¦-106¦E longitude in the middle part of China. To the south of Qinling the meeting line was an abyssal and giant fault situated from Longmen to the Er Inland Sea where the Tibet-Gansi fold system was intersqueezed to the Sidluan platform; to the north of Qinling, situated on the Fengxiang subsidence of the Eerduosi basin, the meeting line was located about 105¦E in Mongolia and appeared in the form of an arcuate structure, i.e. the Mongolia arcuate structure, which could extend to Beijiaer Lake towards the north. A new special type of structure named rotation-apart structure occurred from Gansu, Qinghai province to Ningxia, Neimeng autonomous region, in the west of Shandong province and in the western part of Chaidamu Basin.

Jan 1, 1987

By Marton A

The Readymix Group have a Quarry Improvement Program - 'Building in Quality (BIQ) which has many parallels to the ICI Explosives' total quality management - 'Quality Improvement Program' (QIP). Both companies have for some time recognised that the 'do it right first time' principle means less wasted effort and materials, that efficiency breeds profitability and so actively promote the quality culture. To install the principles and generate the culture requires considerable commitment and effort from the top down and invariably spreads to the suppliers and sub-contractors. Understanding the component processes involved with the quarry operation, analysis of those processes and gaining a breakdown of the cost of non conformance then allows the astute quarry operator to make the necessary changes to improve the process to realise profits. This paper outlines the steps in such a process and the profitable outcomes of the commitment to continuous improvement at the Nickol Bay Quarry.

Jan 1, 1994

By McMullen P. H

Mining of copper ore at Mount Lyell has been continuous since 1893. The operation has always been marginal and the depressed copper Market over the last decade has seen mining continue on the basis of a series of short term plans. In 1985 it was determined that the mine would close in 1989 on completion of the 40 Series mining block. Significant changes in the value of the Australian dollar in 1986 and the subsequent effect on profitability dictated a review of the Company's operations. Lower level ore reserves, mining methods and ore handling systems were re-examined and a plan proposed for mining of the 50 and 60 Series mining blocks. The improved economics of this plan, together with workforce and State Government initiatives resulted in an extension of mine life to 1994.

Jan 1, 1988

The potential of the developed multi-dimensional analysis system to assist interpretation from large data sets through derived digital mapping models is presented accompanied by preliminary results. The concept learning model is original and its application general. Applications exist in general science, engineering, earth resource management and economics. The developed system incorporates advances in machine learning, neural networks, object-oriented software engineering, knowledge representation and fuzzy logic. ' The specific application presented involves automatic earth resource modelling and assessment involving geological theories of mineral potential. The developed system functions as a new and powerful mineral exploration tool, To date the model has been trialled on an earth resource database and several published data sets. A more general potential application is knowledge discovery within databases. The specific theory that is tested in the experimental results is the nature of the cause-effect relationship between the hypothesised geological causes and the measured effects within a previously published test survey. Also integrated here are a neurophysiological cerebellar model of human learning, a new concept similarity measure for pattern recognition, modelled components to explain human concept formation through knowledge discovery and a means of permanent representation.The implementation is as a new artificial neural network architecture functioning as a hybrid expert system. Understanding of programmed concept learning is extended through the model. Also established is a basis for a new approach to multivariate data analysis. Spatial analysis for decision support is integrated over many dimensions, relationships, data types and data modes. Application of the developed methodology and system adds value to data bases. Discovered knowledge is represented as new generalisations, interpolations, classification hierarchies, aggregations and associations within a dynamic, maintainable and reusable integrated knowledge framework. New digital knowledge products and intelligent access follow. Permanently stored, maintainable, easily accessible and discovered knowledge improves decisions through extended hypothesis testing, spatial data analysis and inferencing, prediction, logical deductions and explanations.

Jan 1, 1995

By Yamamoto Y, Ohyama H

In case of NATM, mechanical cutting is desirable in view of the original purpose of not spoiling natural ground. As typical tunnelling machines, there are two (2) kinds available: one is "Full Face Excavator" known as TBM (tunnel boring machine), and the other is "Roadheader" known as Part Face Excavator. By the use of the former, accurate profile cut is made possible, but there is a limit in the shape of a cutting section. By the use of the latter, cutting of various sections is made possible, but in order to cut a section economically and accurately, operators are required to have a high level of skill. In this text, we introduce Automatic Controlled Profile Cutting System (hereafter "ACPC" System) developed as a roadheader.

Jan 1, 1987