Search Documents

By Stone I

Tahmoor Mine is located in the southern Sydney Basin 80km south-west of Sydney and produces 1.2 MT of Bulli Coal annually. Bord and pillar methods used to date will be supplemented by a longwall system. Difficult roof conditions have been experienced since mining began in 1979. A dominantly horizontal stressfield promotes shear failure in the thinly interbedded roof sequence of shales, laminites, siltstones and fine sandstones. General roof conditions and failure characteristics are related to the angle between the roadway direction and the principal horizontal stress direction. The apparent stressfield changes direction, magnitude and the ratio of principal horizontal components across the mine workings in response to both in situ and mining induced causes. Initial roof support of 5 x 2.1 m bolts per W-strap at in intervals, with mesh, was upgraded to include RSJ's in order to support areas of failed roof. This support system was inefficient and costly. A third system of support emphasizes roof reinforcement with full resin encapsulation of 2.1 m bolts in W-straps. The number of bolts per strap (6-8), extra butterfly straps and bolts, and W-strap spacing is determined for each area by expected roof and stress conditions. Intersections are pre-bolted and ribs are supported in some areas. Pillar dimensions, order of drivage and roadway width have each been altered to improve roof control. The intensity of roof deformation at the face varies from panel to panel and causes development rates to decrease to 30% of the maximum. 1. Manager, Tahmoor Mine, Tahmoor, N.S.W. 2. Senior Geologist, BP Coal, Picton, N.S.W. Roof conditions in each area of the mine are characterised and then projected to future development areas based on the relationship between stressfield orientation, relative roadway direction and face conditions. Planning information available includes expected development rates, roof support requirements and areas of changing conditions. Future improvements of strata control involve defining support design parameters for the range of mine conditions already seen at Tahmoor.

Jan 1, 1986

By Yinxiang W, Chunlai Y

In older to improve efficiency of surface pre--grouting in sealing off water in heavily water-bearing strata, such as sandstone,siltstone and limestone, several methods have been used in China, they are ; intermittent pre-grouting, adjusting pre-grouting parameters and stepwise repeated pre-grouting methods. The paper describes effect of deviation on water sealing in pre-grouting. Deviation correction measures, like mechanical, technological and changing hole position methods have been introduced with satisfactory results in practical engineering projects without increasing the volume of engineering project and without causing delay.

Jan 1, 1988

ATTENTION has recently been directed to the subject of dust production and methods of allaying same in the Broken Hill mines, so that the time would seem opportune for the local branch of the Institute to discuss certain features of an important phase of the health question in connection with underground work. Tests conducted in the Broken Hill South mine and at other mines at Broken Hill have shown that the ordinary operatioils of mining, such as boring, blasting, and shovelling, may be accompanied by the production of considerable dust unless water is judiciously used.In South Africa·dust particles under 5 microns size are regarded as dangerous, becailse they are so small as to be invisible to the naked eye, and wm esc'ape the protections set up by nature in the nose and throat, and thus may be inhaled in large quantity. A micron is 1 25000th part of an inch. This paper contains an account of the work done on the Broken Hill South mine chiefly, though some tests were done on other local mines.An acknowledgment is due to Mr. T. A. Reid, of the Broken Hill South mine, who conducted some of the tests herein mentioned, and under whose supervision most dust counts were made. Numerous dust samples have been taken by means of thekonimeter, an instrument designed by Dr. Kotze, the Government mining engineer of the Union of South Africa, and fully described...

Jan 1, 1921

Arrow Energy NL has been operating a number of coal seam gas wells in the Darling Downs region of Queensland. At the time of writing this paper, the region is enduring an extended drought period. The local aquifers are depleting and have not been significantly recharged in over a decade. The local communities (both rural and townships) are struggling to obtain water. Currently, coal seam gas (CSG) operators (under licence) draw water from the coal seams as part of the gas production process and the majority of operators choose to evaporate this water, as it is characteristically brackish to saline in quality and as such must be contained. Although the water produced from one CSG operator is not sufficient to drought-proof the greater area of the Darling Downs, there is potential to supply smaller local areas and contribute to the sustainability of these communities. This paper outlines the work completed by Arrow and its local community partners on the Darling Downs to date, and discusses the application of the produced formation water for:stock watering in feedlots, as a feedstock for coal washing, as a potable water supply for Dalby, as an agricultural water supply for cotton farming, and use as a medium for growing salt-water fin fish.

Jan 1, 2006

The great variety of geological conditions in French coal deposits has obliged the industry to develop different thick seam mining methods. In very steep seams in a dense deposit where stowing is necessary to avoid spontaneous combustion, surface subsidence and water problems, a rising horizontal slice method is used, the coal being hard enough and the seams regular (Lorraine). In very thick and irregular steep seams where the stowing is not necessary, a sub-level horizontal slicing is used; a third method has to be used in Dauphine.

Jan 1, 1976

Western Mining Corporation began shaft sinking operations at it's Foster orebody, south of Kambalda, on the 20th June, 1984. The top levels of the orebody are currently being mined via a decline some 1.5km away.Long term plans require the shaft and decline to combine and produce 400,000 tonnes of nickel ore per annum. Eventually all of the ore produced will be hauled up the shaft.The shaft is 4.5m in diameter and the target depth is 760m. Ground conditions to date suggest there will be no further need for concrete lining beyond the oxidised zone. As such, the sink is an open-shaft development in competent basalt rock. Shaft furniture will be installed on completion of the excavation to the target depth.This paper summarises the experience in the project to date, along with comparisons to conventional shaft sinking methods employed in previous years at Kambalda Nickel Operations.

Jan 1, 1985

Laboratory experiments have been used tostudy a wide range of convective processes which are significant for the formation of rocks and the ores that form in them. Metal-rich solutions flowing through the sea floor produce 'black smoker' chimneys; both the size and structure of a solid chimney and the height to which the plume of effluent rises above it can be predicted using model experiments. Analogues of processes in solidifying magmas can also be studied using crystallizing aqueous solutions. The release of lighter or denser residual fluid as crystallization proceeds, and the resulting compositional convection, have a vital influence on the differentiation of initially homogeneous magma and on the evolution of stratified magma chambers. Mixing during the replenishment of magma chambers, and its dependence on the rate of filling and on the fluid properties, have also been studied on the laboratory scale. Experiments carried out in different geometries have been applied here to the formation of platinum and chromite ores and komatiite lavas. Larger-scale mantle convection, in particular the motion of subducting plates and plumes rising from the core-mantle boundary, also determine the tectonic settings in which ore bodies form. These phenomena too can be usefully investigated in laboratory experiments using very viscous fluids.

Jan 1, 1990

By Hewitt D

A study of two laterite profiles developed on a serpentinite near Rockhampton, shows that loss of Si02 and MgO results in the relative concentration of Fe203, A1203 and a number of minor elements. Serpentine is broken down to form montmorillonite, goethite, quartz and kaolinite. Enrichment of nickel occurs, and it is shown that the element is mainly associated with montmorillonite and serpentine. Highest nickel values are associated with a zone in the profile which occurs at a depth of 10.5-22 metres, and the bulk of the nickel in this zone (42-80%) is associated with the

Jan 1, 1974

By Hughes CA

The need to recover metals from low grade deposits, old tailings, etc., combined with improvements in equipment design and the development of new extractants, has resulted in solvent extraction (SX) metal recovery reaching new importance (Webster & Ferron, 1993). The basic principle of solvent extraction is the use of an equilibrium system in which a metal ion is transferred from an aqueous phase into an organic phase, (Equation 1), (Ritcey, 1984). M + E ME . (1) The organic extractant (E) is usually specific for a certain metal ion (M) and forms a metal complex in the organic phase, leaving the impurities behind in the aqueous phase. To recover the metal, the equilibrium is reversed and the metal ion is transferred back from the organic to another aqueous phase in a process called stripping. The metal is then recovered from the aqueous strip solution, usually by electrowinning.

Jan 1, 1990

By B Banerjee, N Kumar, S Parihar

Rampura Agucha Pb-Zn Mine (RAM) is located about 200 km to the south-west of Jaipur in the state of Rajasthan, India. Open pit mining operations commenced in 1988 and continued to 2018. RAM open pit footprint is the largest in India with length of 2000 m, width 1500 m and depth of 400 m. Development of an underground mine under the operating pit commenced in 2013, through trial mining longhole open stoping with cemented backfill was established as a preferred mining method. Nine years in operations underground mine has reached the production capacity of 4.5 MT, which represent more than 70 per cent of the ore volume mined by the pit. RAM is currently the world second largest underground Pb-Zn mine.

Nov 29, 2022

An improved technique for the quick and accurate measurement of the weight and centre of mass in the horizontal plane of large machines has been developed. On-site weighing of large plant such as bucket wheel dredgers is an important part of the commissioning procedure. The results from the weighing assist in determining the stability of the machine and also enable confirmation of the structural weight distribution used for stress analysis at the design stage. In this paper the techniques previously used for weighing are reviewed and the sources of error using these methods examined. A full descrip- tion of the current technique and procedure is given explaining how the measurement system comprising strain gauge load cells, displacement transducers, wind speed and direction sensors, data logger, computer and software was developed to enable quick and accurate measurements to be made. Proposed modifications to software necessitated by the replace- ment of current measuring instrumentation and computer are discussed. A typical example of measurements from the weighing of a large dredger, illustrating the accuracy of the new technique is given and the calibration technique used to check the accuracy of the force and moment measurements is explained. An outline of how the results are used to certify the machine for operation is given.

Jan 1, 1989

By Howes PM

In the iron and steelmaking processes, dusts are generated and treated by wet dedust- ing methods to form slurries which are high in iron content, but also contain certain impuri- ties. For many years these slurries have been processed and the wet cake, which is produced, has been dumped because of the high zinc and alkali chloride contents. Sintering is an appropriate process for recycling of these materials, provided the deleterious impurities can be kept under control. Zinc is a deleterious element in blast furnaces because it promotes the formation of accretions on the upper walls of the furnace. This results in irregular furnace performance. Alkali chlorides effect the emissions from the sinter plant waste gas due to the high resis- tivity of these components, resulting in decreased efficiency of the electrostatic precipitator. Experimental work indicated a concentra- tion of zinc in the -11 pmt particle size frac- tion. A cyclone plant was installed producing a "coarse" usable product and a "fine" waste Product.

Jan 1, 1984

By M Byrne, P Newman, M Lindqvist

SomincorÆs Neves Corvo Mine, one of the largest copper producers in Europe, is currently constructing a paste backfill plant in order to replace cemented rockfill in its bench and fill stopes and possibly replace hydraulic sandfill in the drift and fill stopes. A 250 m flow loop was constructed at the mine and the flow properties of various paste blends were investigated. Cycloned tailings and total tailings were both pumped successfully as pastes and were also combined with waste rock for additional testing. The pressure losses in 102 mm and 154 mm diameter pipeline were recorded at flowrates up to 60 m3/hr and are presented at slumps from 120 mm to 250 mm. The data showed the sensitivity of paste mixtures to slight changes in consistency, confirming the need for accurate control during paste production and distribution. The flow results clearly showed the different paste behaviour between cycloned and total tailings pastes and the change in properties at low and high slumps. In addition to pressure loss data, strength testing was done on 38 mm and 82 mm diameter samples. Further strength testing is ongoing at the mine using fly ash as a supplement to cement, reducing the overall binder cost. Preliminary engineering for the underground distribution system is briefly discussed, with reference to the siting of the plant. The Neves Corvo Mine is particularly shallow and alternative methods to pumping were sought in order to ensure sufficient hydraulic head for underground distribution. The comparison of options had to take into account the capital and operating costs, the operation of the plant and the impact on the future expansion of paste fill utilisation at Neves Corvo.

Jan 1, 1998

By Ryan A, Dennis R, Dekker D, Ellis W, Sowerby B

An automated facility for non-destructive elemental analysis of mine samples has been developed and tested at Mount Isa in association with the CSIRO. The analysis is based on the prompt and delayed measurement of gamma radiation emitted by the sample during and after separate fast and thermal neutron irradiation. No sub-sampling or sample preparation is required and the analyser is operated by one person that would otherwise be splitting drill core in preparation for conventional analysis. The analyser has been calibrated to measure the following (precision in parenthesis): Ag (14 ppm), Pb (0.5 wt%), Zn (0.5 wt%), Cu (0.04 wt%), Fe (0.7 wt%), S (1.1 wt%), SiO2 (0.8 wt%), A1203 (0.07 wt%), Mn (0.05 wt%), specific gravity (0.02 g cmt). Crushed or whole drill core samples that range in size between 0.5 m and 1.8 m of equivalent BQ size drill core can be analysed at a rate of six samples per hour. If required, drill core samples can be re-packed in their original configuration for storage following analysis. Standard samples are measured every day to ensure operational stability. The analyser is controlled by a personal computer which prints the results and stores them along with the raw data on the computer hard disk. This paper reports the performance of the analyser during 1992 for routine analysis of drill core from the lead ore bodies of both Mount Isa and Hilton mines.

Jan 1, 1993

At Hilton Mine, 18 kilometres north of Mount Isa, the silver-lead-zinc sulphide bodies have undergone strong deformation in the form of folding and later faulting and brecciation in the hangingwall region of the mine. Variation in grades and widths over compara- tively short distances causes problems regarding accurate sampling of orebody exposures in underground development, and in defining confidence limits for the extrapolation of ore intersections in ore reserve calculations. The paper gives a preliminary insight into the problem of obtaining representative samples for exposed orebodies and discusses the sampling techniques employed. Results gained from these sampling methods could not be verified due to lack of individual bulk samples for comparison but strong evidence for precision was provided. INTRODUCTION In a developing mine like Hilton, accurate grade information is of extreme importance. Original grade information for a potentially viable ore deposit is gained from surface drilling, and initial ore estimates are calculated from the resultant ore widths and grades. After underground development has proceeded, the opportunity arises for detailed examination of orebody exposures, and the resultant assay grades and widths from sampling of these exposures may, in the long term,

Jan 1, 1976

By S C. Dominy

The Bendigo Goldfield is located in the state of Victoria, Australia, and is one of a number of quartz-reef fields that make up the greater Central Victorian Goldfield. At Bendigo gold particles are characterised by their very coarse nature, ranging from below 100 to over 10 000 ¦m in size. Some 60 per cent of the gold occurs in particles greater than 1000 ¦m in size. This characteristic ensures that the mineralisation is very challenging to both sample and evaluate. Diamond drilling provides a measure of geological structure, but is a poor measure of in situ grade, understating it by up to 75 per cent. Drilling combined with on-reef development, bulk sampling and geological interpretation has been used to define Indicated Mineral Resources. For grade control, a balance had to be sought between sample representivity, cost, turn around time and practicality. Sampling of extreme nugget effect deposits generally requires the use of bulk sampling in order to be representative. However, the cost and turn around time is significant. As a result, a 50 kg micro-bulk sampling system has been introduced that attempts to overcome these problems by providing a fast, practical method that can discriminate between ore and waste. As the mine passes into production, grade control will increasingly become dependent upon geological data collection and interpretation.

Jan 1, 2005

FOR some years after the erection of the first chlorination plant at Mount Morgan the ore sent to the works for treatment was mined entirely from the oxidized zone; consequently, the bullion recovered at the refinery was of unusual purity, averaging about 972 in fineness, and, as no impurity in any way detrimental to the softness or toughness of the bullion was present, there was no necessity to subject it to any refining process.The charcoal from the filters was calcined to ash in small reverberatory furnaces of the usual type. The ash was mixed with suitable proportions of soda and borax to form a good liquid slag. This' mixture was then charged into salamander cruciblesand run to metal and slag in the ordinary wind furnaces-a slow and tedious proceeding in the Mount Morgan climate. The bullion, cleaned of slag, was re-melted under borax and poured into bars weighing from 350 to 400 oz.; these bars, after being dipped while hot into dilute sulphuric acid, were packed and sent to the mint. Of late years, however, the ore coming from the deeper ground of the oxidized zone became much lower in gold values, and contained variable but increasing quantities of sulphides, sulphates...

Jan 1, 1911

By Kennerley P

A significant part of the reserves of the Southern Coalfield lie beneath major water storages and their impounding dam structures. One of the functions of the NSW Government's Dams Safety Committee is to specify the particular mine layouts which can be used beneath the stored waters according to certain guidelines. A study was made of examples of the two different methods of extraction used under the stored waters as proposed by the mining company according to the guidelines and approved by the Dams Safety Committee. Using both pillar monitoring and mathematical modelling approaches it was shown that the recovery of coal from these layouts could be improved while still ensuring the long term stability of both the underground support pillars and the body of the strata. The integrity of the water storages and their impounding structures would therefore not be Affected.

Jan 1, 1986

A mining companyÆs approach to managing the risk of theft of explosives and initiating devices should be underpinned by an organisation-wide policy developed with internal and external consultation. It should be based on the principles of sound proactive risk management, planning, monitoring and remedial action. This paper aims to provide mining (and construction)organisations with the rationale and many of the tools they need to control explosive security risks. As with all legislative compliance, they are best managed by incorporating the statutory and legal requirements into company policies, management systems and plans, operating procedures and culture. This is the approach that has been adopted in this paper. Trends we should expect: more prescriptive legislation and stricter government regulations; enhanced enforcement and more prosecution; more sophisticated detection systems, eg airports; additional compliance costs; additional vigilance on record keeping; improved risk awareness and risk communication; wider use of explosives policies, management systems and plans; and additional security staff with investigative skills.It should be noted that mining companies will be required to play their part in reducing the likelihood of explosives, intended for mining purposes, being wrongfully used to threaten, hold to ransom or to injure individuals or members of the public or to produce property damage. This will be done by putting in place safeguards to reduce the risk of theft of explosives while they are under their control. On that basis, this is a business risk assessment rather than a hazard risk assessment. A conclusion of this paper is that mining companies can and should play their part in reducing the supply of explosive materials that can then be used for illegal activities. In fact, mining companies have always had this duty, but now the stakes are higher û æcomplacency no longerÆ.

Jan 1, 2004

By Haslam C. O, Taylor S

Four historical periods of Australian lead-zinc-silver exploration and development are identified.In the first period, 1841-1900, Australia's deeply weathered surface yielded bonanza deposits. The outcrops of easily worked secondary ores, enriched in silver and lead, were discovered by prospectors with the incentive of production at times of high silver price. Districts discovered in this period still contributed, in 1982, 60 per cent of Australia's lead-zinc production, mainly from Broken Hill.The second period 1901-1944, was one of strong mine development but stagnant lead-zinc-silver exploration. Mount Isa was discovered and developed, but otherwise effort was devoted mainly to the mining of deposit extensions and to the metallurgical flotation of zinc. The deposit discovery rate was low but the discovery of Mount Isa was so significant that discoveries of this period contributed, in 1982, 30 per cent of Australia's lead-zinc production.The third period 1945-1972 was one of re-invigorated exploration.New geological and geophysical surveys, developing concepts of ore genesis, and worldwide comparisons of orebody settings improved target area selection. Evolving remote sensing methods, and rapid analytical techniques, assisted detection of lead-zinc deposits. Initiation of exploration led to discovery:1. in regions of previously unsuspected lead-zinc-silver potential (Sorby Hills, Mons Cupri, Golden Grove).2. of poorly exposed deposits in recognized mineral districts (Hilton, H.Y.C., Woodlawn, Elura, Que River).3. during active exploration for another commodity (Brown's, Woodcutters, Mary River, Beltana, Lady Loretla and Pegmont).The period saw a sustained growth in lead-zinc-silver production mainly from established operations. Mines discovered during the third period contributed, in 1982, 7 per cent of Australia's lead-zinc production.In the fourth period from 1973 to the present, exploration initiatives became fewer but resulted in continued discovery of poorly exposed deposits at Teutonic Bore, Thalanga, Benambra, Scuddles, Hellyer, and Jillawarra. Development initiatives strengthened in the period and production commenced at Woodlawn, Teutonic Bore, Que River and Elura; pre-feasibility work commenced at Scuddles, Hilton, Lady Loretta and Thalanga.

Jan 1, 1984