Search Documents

By Greenhalgh L. P H

The opportunities offered by an increasingly volatile world invite the international consultant or engineering services contractor to broaden attitudes, diversify interests, expand capabilities, retain and develop specialist skills and base judgements upon sound principles and solid experience. The wide-ranging scope of this review reflects such a change but the topics of discussion are not intended to be exhaustive or to detract from many other current developments.The subject of environmental protection, effluent control and pollution prevention is a primary consideration in the application of many mineral processing technologies but is not covered here. There is an array of developments relating to noxious gas emissions and toxic wastes and the paramount importance of this matter justifies comprehensive conferences dedicated solely to the application of suitable measures. This review concentrates therefore on the main stream processing techniques for the primary recovery of values.

Jan 1, 1993

Changes in mining technology have led to an increase in the number of underground sulfide dust explosions reported in Australian and overseas mines. Samples collected at the Elura mine consisting primarily of pyrite, pyrrhotite, arsenopyrite, sphalerite and galena, were tested in 8 litre explosion chamber. The dusts were found to be capable of producing dangerous dust explosions with maximum explosion pressures of 440 kPa and rates of pressure rise of 5200 kPa/s. The hazards of a sulfide dust explosion are associated with the pressure wave and flame front of the explosion and the toxic gases remaining after the explosion.

Jan 1, 1984

By Gross A. E, Neville P. C

Over the last decade heap leaching with a cement binder has allowed the economical leaching of low grade gold ores of less than 2 grams/tonne. Despite the continued use of cement as an agglomeration aid, numerous leaching operations continue to experience channelling and blinding problems. This paper describes the development of polymeric agglomeration aids, Extract Ore 9760 and 9960, which when used as a partial cement or lime replacement can result in a higher rate of and/or a higher total gold recovery in plant evaluations. Extract Ore in combination with cement acts to produce a stronger agglomerate which results in reduced fines migration during leaching and helps prevent blinding of the heap. Both of these changes will give a more even flow of cyanide solution throughout the heap and improve solution contact efficiency within the ore. Polymeric agglomeration aid programs are now being used by heap leaching operations in three different countries. A summary of benefits identified at some of these operations are presented in this paper.

Jan 1, 1994

By Edwards R

Greater efficiency of capture of minus 6 mm to fine micron size particles of free gold is achieved with the Knelson Concentrator. The development, principles of operation and recent innovations relating to this enhanced gravity concentrating device are described by the inventor, followed by a description of application and consequent economic benefits in low grade alluvial gold deposits by a large scale user of Knelson Concentrators in the Northern Territory of Australia.

Jan 1, 1990

Both as an energy source and as a raw material, natural gas is playing an increasingly important role as a catalyst for the development, continuation and rebirth of mining projects in Australia. Pipelines are the vital link in making natural gas available to a region and to individual mines. This paper will cover the role of pipelines in supplying mining projects in Australia, the development and status of the Ballera to Mount Isa gas pipeline and the future prospects for gas pipelines in the Carpentaria Mineral Province.

Jan 1, 1998

By Tagawa H

In Japan, geological condition do not only vary in a wide range of strata but are also extremely complex with the existence of faults and aquifers. With respect to rocks, in particular, it is very rare that homogeneous rocks are distributed uniformly. In general, geological conditions are distributed in a wide variety, ranging from earth, sand, soft and medium rocks to hard rocks. Under these geological conditions, when planning of the tunnel construction is to be made out, either blasting method or tunnel boring machines must be selected taking into consideration the geological structures along with the designed tunnel route,' possibility of encountering aquifers, hardness of rocks anticipated and also, the adjacent environ- mental conditions. In the process of select- ing an excavation method,, it is important to make a comparative investigation between the above two methods considering the advantages and disadvantages with regard to the respective operating efficiency, economical efficiency and the conditions and scope of application as well. Furthermore, in addition to these considerations, the recent environmental restriction, which does not allow the blasting in the surroundings of residential areas, must also be taken into account. Because of this, in some cases there is no alternative but to use a static excavation method or a tunneling machine even when these are less efficient than blasting.

Jan 1, 1987

By Koh P. T L, Varnas S. R

Fluid flow, heat transfer and combustion in a nickel flash smelter have been investigated by numerical modelling and flow visualisation. The three-dimensional numerical model incorporates turbulent two-phase fluid dynamics, radiative heat transfer and combustion. The main features include the use of the k-E turbulence model, the Lagrangian tracking of particles, radiative heat transfer based on the spherical harmonics method, and chemical reactions. The predicted flow fields are in good agreement with data obtained from a series of flow visualisation experiments on a cold water model. The interaction mechanism between the fluid flow and the solid particles is examined for a range of particle sizes both with and without injected oil in a series of simulations. The heat transfer in the shaft is dominated by combustion and radiation, whereas the ignition of particles is influenced by the particle size and the added oil. Flow and temperature fields for both gas and solid particles are presented as well as the fraction of sulphur removed from the particles.

Jan 1, 1992

By Heidecks C

Sub-level stoping with consolidated rockfill is the main method for mining steep dipping baryte and fluorite veins in Germany. Drifting is fully mechanised using drill jumbos, LHD units and shotcrete support. Stopes have heights up to 50 m with sub-level distances up to 15 m. Winning of the pillars between sub-levels is done by longhole blasting in slices of 3-5 m length on strike. Mucking is done on the lowermost level by LHD units. After each blast rockfill with binder (cement and/or fly ash) is dumped into the scope from the uppermost level. Economic success depends on both geological and technical parameters and factors, eg vein thickness and dip, ore grade, size and distance of sub-level drifts. Of particular influence are ore loss in pillar winning and dilution both in drifting on vein and in pillar mining. A comprehensive computer program has been developed for calculating the total cost per tonne run-of-mine ore respectively per tonne of concentrate for a single stope. The cost model includes development, longhole blasting, mucking and haulage to the mill, milling and ventilation. All costs (labour, energy, supplies, maintenance, depreciation and capital cost) are taken into account. Dilution and recovery are both considered. The program can be used to estimate the cost of mining a particular stope. It can also be used to investigate the influence of relevant parameters and factors on the economic result. By this way it should be possible to optimise the technical design of a stope.

Jan 1, 1995

In 1972, metallurgical testwork on Renison ore indicated a significant proportion of low specific gravity, tin-barren material ideally suited to heavy medium separation (HMS). Further technical and financial studies provided adequate economic justification and in December 1974 the Renison HMS plant was cannissioned. Initial operations were interrupted by the imposition of tin production quotas for three months in 1976; they were also beset with difficulties particularly with regard to mechanical wear. During the first two operating years much develognent work was carried out including installation of a pyrrhotite flotation bank in the medium recovery circuit, investigations into various wear-resistant materials and the use of atanised rather than milled ferro-silicon. By 1977/78 financial year satisfactory performance had been achieved and since then the average floats rejection has been 18.8% of the total ore treated with an associated tin loss of 2.96%. Developnent has nevertheless continued during the last three years, principal modifications being the installation of larger aperture desliming screens and improvements to the overdense cyclone circuit.

Jan 1, 1978

By Robbilliard K. R, Floyd J. M

The problems facing the metallurgical industry from the viewpoint of the range of unacceptable residues, flue dusts and slags currently produced from the electrolytic zinc process, electric arc furnace scrap treatment, and blast furnace operation in lead smelting and the Imperial Smelting Process (ISP) are addressed. The application of the Ausmelt technology is discussed and analysed for the pyrometallurgical treatment of zinc plant residues, steel plant flue dusts and lead blast furnace and ISP slags, as well as the more complex issue of smelter modernisation to avoid production of zinc plant residues in the future. Processes developed from pilot work are described and indications of the economics of treatment of electrolytic zinc plant neutral residue and jarosite are given.

Jan 1, 1993

By Fukuichi K, Matsukawa H, Nakagawa M

The Myojin Tunnel, located on the Shikoku Expressway being constructed by the Japan Highway Public Corporation, is 3,770 m long with a cross sectional area of 80 m2. Kajima Corporation, the contractor for the northern construction section of this tunnel, adopted here its newly developed "mini-bench" method of excavation. The objectives of this method were 1. to be able to perform all tunnelling operations using the whole cross sectional area of the tunnel under any ground conditions, and 2. to be able to vary the length of the mini-bench within the range of 0 to 7 m according to ground conditions. In order to achieve these objectives, original, sophisticated equipment was developed and employed in the work. One of the newly developed machines is a special jumbo, a hydraulic crawler jumbo with five rotary type booms. This machine is capable of accommodating variation in the length of the mini-bench accompanying changes in ground conditions and is equipped with a special mechanism by which the positions of the booms can be controlled by means of hydraulic cylinders. Also developed was a shotcrete robot for use with the mini-bench method which has the control board near the shotcrete nozzle for close control of application.

Jan 1, 1987

By Lloyd C. J

The uranium markets are at present well covered by available producers. However the predicted increase in demand, recently reinforc- ed by the Arab oil crisis, will by, the early 1980s'outdistance supply. Current trends are towards light water reactors with-fast breeder reactors not expected to make any significant impact to the mid 1980s. The proposed lifting of the US embargo on the use of foreign uranium in US reactors will expand the market available to non US producers. A balancing in supply and demand worldwide will probably occur in the early 1980s. Australia's potential producers at present hold about 20 percent of the worlds U308 resources. Three companies, have contracts to supply nearly 10 900 tonnes of U308 between now and 1986 which represents about 1 percent of the predicted demand to 1986. Australian producers need to establish themselves more firmly in the market place in order that other countries will not replace us. Contracts can be written now which will allow for world market prices to be paid in the future, thus protecting the Australian producer.

Jan 1, 1974

By Bof J, Lowe S

BHP's newest colliery on the Southern Coalfield Is Tower Colliery. It is situated near Wilton some 60 kms south west from Sydney. It commenced its operations in 1978 and since that time has experienced considerable roof problems. In its eight years of operations, production has been 936 687 tonnes to December 1985. To a certain extent this is a reflection of the ground control r,,b1cros present in the colliery. paper out Iines the signif mt g,, logical features that are known to exist in the colliery and their influence on roadway development. Faulting has hindered the mine's development and an igneous intrusion has had outhursting associated with it. The prevailing roof rock has also had an impact on the roadway conditions. The paper will look at intersection deformation in present workings. Extensometers have been installed in these areas and provide measurements to verify visual observations. The results show a significant increase in roof movement as the roadway is developed from a single heading, to a T-intersection and then Into a four-way intersection.

Jan 1, 1986

By R Rodriguez, S Gumo

The Lihir Gold Mine, in Papua New Guinea, is a large open pit operation within an active geothermal system inside a collapsed volcanic crater. This unique setting has a big impact on the mine operation because of the occurrence of geothermal hazards. The system for managing geothermal hazards that has been developed by Lihir Gold Mine is a pioneering effort that can be applied to future mine discoveries in a similar environment. The controls are integral to the mining operations and allow mining to proceed whereas without them mining could not be considered. Truck and shovel productivities in conventional open pit operations are constrained by diggability, equipment availabilities and utilisation. At Lihir, additional constraints are in the form of 100 m exclusion zones around working shovels and 50 m exclusion zones around working drills. Given that the mine has seven large digging units and six drills, this amounts to a lot of area that excludes the presence of people on the ground. So how are the necessary work like grade control, survey, blasthole loading, and in-pit maintenance performed safely to achieve production targets? The answer is in the highly specialised procedures that have been developed that utilise geological, geothermal and geotechnical knowledge to predict problem areas and also deal with the organisation of movement in the pit for people and mining equipment. This paper will detail how scheduled material movement can be maintained despite the challenging conditions faced at Lihir Gold Mine.

Jan 1, 2007

Expert systems are a product of Artificial Intelligence (AI), a field of long standing, dedicated to the study of problem solving using heuristics, construction of symbolic representations of knowledge about the world, communications proce

Jan 1, 1998

By Christie A. B, Swain A, Brathwaite R. L

This study provides quantitative data on vein distributions within seven selected epithermal systems, four deposits hosted predominantly in rhyolitic rocks: Ohui, Wharekirauponga, Neavesville and Komata, and three major deposits mainly hosted in andesite: Martha Hill, Golden Cross and Karangahake. The technique of fractal analysis was used to help quantify vein distribution patterns. The fractal dimensions (D) obtained are related to the number of veins per metre, the degree of vein clustering, and vein thickness. An increase in any of these tends to increase the fractal dimension. It is the relative relationship of these parameters that is important for the characterisation of vein distributions, and the comparison of different deposits. Within the same systems, the rhyolites are characterised by lower vein thickness and vein density, but have a higher degree of vein clustering compared to the andesites. Sections that are deeper and more centrally located within the epithermal system and/or close to major structures, tend to have a greater degree of vein clustering, higher average vein thickness and density, and higher thickness to density ratios. This depth control is most pronounced in epithermal gold-silver systems because they have formed at shallow crustal levels where physico-chemical conditions change drastically both vertically and laterally. In addition to lithological and structural control at vein scale, deposit scale structure is of great importance in the deposition of economic mineralisation. Large open vein structures capable of sustaining high fluxes of hydrothermal fluid, favourable for the formation of large, high-grade gold deposits, are best developed in andesite sequences.

Jan 1, 1995

By Baafi EY

Geostatistics is now widely used in the mining industry in the estimation of ore reserves and terms like kriging, variogram and estimation variance are becoming well known. Ordinary Kriging (OK) has been found by some practioners to be a superior tool compared with other ore reserve estimators. However, kriging hasn't been the ultimate solution to difficulties which may arise in ore reserve estimation. Several additional geostatistical techniques have been recently developed for more efficient ore reserve estimation in some deposits, especially gold and other precious metals. These include indicator kriging and probability kriging which are useful tools to work with in a selective mining operation.

Jan 1, 1987

By Etheride MA

The evolution of economic precious metal and copper-gold deposits in high-level igneous terranes is dependent on very efficient fluid focussing. This is most readily achieved by contemporaneous deformation, igneous intrusion and hydrothermal activity. Mineralisation in these environments generally occurs in fault and fault-vein arrays developed in the cover sedimentary and volcanics sequences above older regional scale fault systems. Such reactivated fault systems an particularly prone to developing the complex fracture arrays, extreme local dilation and dramatic increases in permcahilit} that are necessary to efficiently focus hydrothermal fluid and produce large mineral deposits.

Jan 1, 1995

By Barnett DW

Financial risk analysis provides the tools to examine the uncertainty of capital decisions in new mining ventures. This paper explores the methodology by which financial risks can be studied and quantified. The most commonly used risk evaluation methods, such as sensitivity analysis and discount rate adjustment, are presented as an introduction to a more comprehensive discussion of stochastic methods of discounted cash flow analysis using Monte Carlo sampling. The discussion is illustrated with examples of a stochastic discounted cash flow. The advantages of Monte Carlo sampling in risk analysis are discussed together with its problems, particularly those originating from the correlation amongst the variables that determine the economic output of a mining venture, and the difficulties created by insufficient data, imperfect knowledge and complexity. The paper also surveys the most commonly used software used in risk analysis.

Jan 1, 1994

Rheology is the science which deals with the deformation and flow of matter. Thus rheology is concerned with the flow of any material. The mining industry is concerned with digging things out of the ground, extracting the good stuff and throwing away the bad stuff. In the upgrading processes associated with mining, ie mineral processing, wet techniques are used where the primary material being handled is a particulate fluid, ie a suspension. After the processing operation, with the concentrates extracted, what is left behind generally is a wet material in suspension form, which may or may not contain reagents harmful to the environment. The amount of waste generated in any of the mining processes is large, in fact, the mining industry is the largest generator of solid waste in Australia. In order to minimise the waste generated within the industry it has become of interest to handle the particulate fluid wastes, or suspensions, at high concentrations, thus removing water and some of the reagents which may be harmful to the environment. The resultant highly concentrated suspension is a non-Newtonian fluid. Rheology deals with the flow of non-Newtonian fluids; therefore a combination of rheological understanding of high density suspensions, in conjunction with an understanding of the environmental problems being faced by the mining industry, can and has led to improved methods of waste disposal in the industry, ie waste minimisation. This paper describes the progress that has been made in the development of dry disposal technology in the mining and minerals industry in Australia.

Jan 1, 1998