Search Documents

A survey of leaching systems for the dissolution of gold has been undertaken and their advantages and disadvantages evaluated both from their effectiveness at leaching and their compatibility with carbon- in-pulp (CIP) and resin-in-pulp recovery. In the near future it is almost certain that cyanidation in some form will remain the leaching system of.choice although economic and environmental pressures could see the introduction of other leaching systems particularly for treating refractory gold ores. The most likely alternative leaching systems appear to be acid chlorine, acid thiourea and ammoniacal thiosulphate. INTRODUCTION High grade reserves of readily recoverable gold ores are gradually being depleted which, inevitably, must create a greater awareness amongst gold producers, of the efficiency and, in some cases, the suitability of present day metallurgical processes for treating low grade, complex and refractory deposits. One of the key steps in the extraction of gold is the dissolution of the metal using chemical reagents which, ideally, should be cheap or recyclable, selective, non-toxic and compatible with down-stream recovery processes. In practice, meeting all these critera is difficult - if not impossible - particularly in view of the stringent environmental impact requirements which must be met Nowadays.

Jan 1, 1982

By Waladan M, Elliot B, Rankin W. J

A survey was undertaken on the Kalgoorlie Nickel Smelter in which samples of slag and matte were taken along the length of the integrated flash smelting furnace and analysed to determine the variation of nickel and iron concentration. At the same time the oxygen potential of the slag and matte was measured using disposable tip solid-state oxygen probes. The results show that the oxygen potential of the slag is higher than that of the matte and that both decrease from the reaction shaft end to the slag tap hole end of the furnace. The slag and matte are not at equilibrium except towards the tap hole end. Reduction of nickel and magnetite from the slag occurs before the slag enters the slag-cleaning appendage by reaction with iron in the matte. Thermodynamic modelling and laboratory experiments showed that the equilibrium nickel and magnetite contents of the slag in the absence of a carbonaceous reducing agent are about 0.4 per cent and 7.5 per cent, respectively. A carbonaceous reductant is required to obtain a lower nickel content in the slag.

Jan 1, 1991

By Jorgensen FRA, Moyle FJ, Turner TM

Laminar flow furnace techniques and thermal analysis were used to study the combustion of Kambalda nickel concentrate and Collie coal. The study was made to ascertain the suitability of the latter as a replacement for the fuel oil currently burnt in a flash furnace at the Kal- goorlie Nickel Smelter. The coal was found to ignite at temperatures between 500-600¦C which was the same as that required for the most reac- tive component of the concentrate, namely py- rite. The rates of reaction of both the coal and concentrate were dependent on oxygen con- centration. Sulfur dioxide hindered the combus- tion of concentrate and of coal, the effect on the concentrate being the more pronounced. The effects of moisture content and the tendency for spontaneous combustion of the coal were also noted.

Jan 1, 1982

The C.S.A. copper lead zinc mine, located seven miles north of Cobar in Central Western New South Wales, is the largest known mineral occurrence in the Cobar Mining Field. Hosted by the steeply west dipping, west facing sediments of the Cobar Group, the generally discordant orebodies occur within a strike width of 600 ft and an overall strike length of 1200 ft. They comprise lenticular steeply north pitching and east dipping zones of sulphide mineralisation which range in composition from massive pyrite-sphalerite-pyrrhotite--galena to less massive pyrite- pyrrhotite-chalcopyrite varieties. The thinly bedded siltstones, shales and graywackes hosting the mineralisation appear to have derived many of their constituents from volcanic sourcesä They have been metamorphosed to the greenschist facies of regional metamorphism. At least two stages of deformation and folding have occurred. The first stage folded the rocks on a south pitching fold axis into their present configuration, and super- imposed a strong axial plane cleavage which subsequently guided the emplacement of the mineralisation. The second stage of deformation is considered to have controlled the zonal distrib- ution of the orebodies and the appropriate fold axis appears to coincide with the long axis of the orebodies.

Jan 1, 1969

By Svenson D

For fully effective information to be obtained from exploratory drilling for coal, drilling programs should be planned systemati- cally in successive stages, on the basis of existing geological criteria and information collated during each stage. In this way, drilling can be executed with optimum economy, aided by auxiliary geophysical techniques wherever these may be appropriate. The object- ives of the programs must ultimately include an adequate assessment of mining conditions as well as thorough evaluation of coal quality. The first of these objectives is not always appreciated by both geologists and mining engineers engaged in supervising drilling pro- grams, often resulting in the need for more additional drilling and more expense than would otherwise be required. To achieve all of these objectives as effectively as possible, the drilling should be supervised by well qualified personnel experienced in working in a multi- dicipline, professional mining, geological and engineering team.

Jan 1, 1977

By Newell R

The situation in which a gas stream flows through a bed of solids is found in many extractive metallurgy operations. Examples include blast furnace smelting, sintering and pellet firing. In such cases the resistance of the bed to fluid flow and heat transfer is of major significance to the operation of the process. This depends on the structure of the bed, which in turn is influenced by the manner in which the materials are charged to the bed. In this work, packed beds of hematite pellets of two different sizes were prepared in which the pellets were charged as a uniform mixture and in layers. The porosity, flow resistance and heat front velocity were measured and compared for the different bed configurations. For layered beds, the overall porosity and heat front velocity increased while the flow resistance decreased when compared with the values obtained for the uniform mixture. The size of the layers also had an effect on flow Properties.

Jan 1, 1991

The author describes 1. The classification and characteristics of various thick seam mining techniques in various Japanese coal mines. 2. Practices of thick seam mining methods experienced in Taiheiyo Coal Mine. Currently, thick single lift, simultaneous multi lift and non simul- taneous multi lift mining methods are adopted as underground flat thick seam excavations in Japan. These are now reliable and effective in increasing the extraction ratio. At Kushiro Colliery of Taiheiyo Coal Mining Co., these three thick seam mining methods have been used. According to the results, if solidification of the top lift goaf is essential, the non simul- taneous multi lift mining method is the most effective in increasing the extraction ratio without minimising productivity of each lift and it points out that further development of this method is necessary.

Jan 1, 1976

The application of new and currently practised mining techniques in new areas and at greater depths necessitates considerable and immediate research effort. This effort is aimed at identifying the factors which make a particular method suitable and economically viable in a given geological, structural and operational environment. These factors, together with greatly enhanced knowledge of a deposit at the exploration and planning stage, allow selection of the most appropriate and efficient mining method in a new area such that coal resource recovery is maximised in a cost effective manner. Current research and future requirements for research into mining methods and associated equipment and mine services are reviewed.

Jan 1, 1981

By Barnes R. G, Agostini A, Lewis P. C

The Mineral Resources Audit is a five-year Program established to produce a comprehensive and objective assessment of the mineral resources of New South Wales, including prospective resources. The goals of the Program are to improve planning and land use decision-making; attract exploration and minerals related investment; help the Department to identify and fill gaps in knowledge; and develop methods to identify and quantify resource potential and prospectivity. To achieve the goals of the Audit it is necessary to assemble and enhance a large amount of information and it is necessary to spatially analyse this information using computer-based Geographic Information Systems (GIS) which allow the collection, storage, transformation and display of large quantities of spatial data. An extensive range of both map-based and textual data can be employed in spatial analysis and resources and geoscience modelling. In order to use this information, data sets have to be corrected and standardised. Many data sets need to be classified. An objective of the Audit Program is the spatial analysis of the State, region-by-region, and the release of cleaned-up multiple digital data sets as packages which include upgraded mineral deposit information, 'seamless' geological map layers showing lithology, structures and stratigraphy, and processed and classified geophysical map layers. These regional packages are important reference sets for the mineral resources industry and will assist delineation of regional exploration targets.

Jan 1, 1995

By McLaughlin R. G, Brammer R. A J

King Island Scheelite had been using dealer modified front end loaders for two years when in 1974 it started to increase production. Suppliers were then quoting long deliveries for underground diesel trackless mining equip- ment, and the Company was forced to modify surface machines which had become redundant as production from the open cut phased out. The results were generally successful and encouraged further adaptations. Drill jumbos excepted, the Company now uses only converted surface machines in areas worked by diesel engined equipment and for all support and auxiliary functions.

Jan 1, 1977

By Mckenzie CK, Leach KR, Bateman KW

Modelling of industrial coal flotation based on data collected in several Central Queensland flotation plants and supplemented by laboratory data is discussed. The model is kinetic in form and provides the basis of an automatic control system. The important features of the model are, 1. a distribution of flotation rates for each species of particles corresponding to the range of particle sizes, 2. a physical restriction on the removal rate of solids in cells where froth 'overloading' occurs. In this condition the removal rate of solids is proportional to the removal rate of water, 3. enhanced particle floatability due to increasing collector addition where froth overloading does not occur, 4. a second mechanism of recovery of all particles by mechanical associ- ation with water. This mechanism is particularly important in the recovery of fine high-ash species.

Jan 1, 1978

By Horrocks KRS, Smitham JB, Ellison JF

This paper describes the development and installation of equipment for continuously measuring separating density in the dense medium cyclone circuits of the four million tpa Port Kembla B/C plant coal washeries. Monitoring equipment consisting of magnetic coils and differential pressure cells were installed in U-tubes taking the full flow of magnetite from the drain sections of the product drain and rinse screens. The monitoring equipment measures overflow magnetics concentration and overflow density continuously and has operated since 1989. From these measurements and calibration trials, the separating density of operating cyclone modules can be inferred reliably. Variographic analyses of the data show that medium density control to +/- 0.002 RD units and separation density control to +/- 0.007 RD units are achievable. Either method for measuring separation density can be used with approximately the same accuracy, although the overflow density measurement technique suffers from the need to have regular flushing of the Dp cells which complicates the signal analysis. Data from the plant shows that separation density can be controlled by regulating medium density, but the assumption of a constant offset between medium density and separation density is erroneous.

Jan 1, 1993

By Schonert K

The throughput of a HP-roller mill is determined by the acceleration of the feed material within acceleration zone and introduction into the compression zone. Both processes depend on the internal friction and the friction of the material on the roller surface which is influenced by the surface structure and adhering of material. The particle motion in the acceleration zone has been investigated with high speed videos showing the effect of the centrifugal force and the slip on the roller surface. The throughput is discussed in the term of the specific throughput which can be approximated by a linear function characterised by the throughput number and the throughput elasticity. The throughput number is a helpful measure for investigating the influence of the feed material and the surface structure. The experimental results give some guidance for chosing an optimum corrugation profile.

Jan 1, 1993

The Jacobs Sliding Floor (Floor) is experiencing a surprisingly long competitive life. The first Floor was used on the Camino Tunnel in California in 1960. At that time the Robbins Company had built only seven TBMs, and the future for such machines was considered doubtful by many, as compared to drill and blast methods. This was then, and still is, commonly called the "conventional" method. Robbins' TBM No. 8 was for the Hydro Electricity Commission of Tasmania (HEC) for their Poatina Hydro Project in 1961. In this writer's view, the Poatina experience was the start of successful hard rock boring machines. But, by coincidence, the HEC is using the newest Floor for their King River Hydro project, where driving with the Floor started in July 1986 on the King Tunnel. This paper examines the history and developments in both Floor design and other "conventional" tunnelling equipment, and the site specific conditions that have allowed this old concept to still be competitive in certain select situations. Parametric costing data and some actual progress records are included.

Jan 1, 1987

Investigation of standard tests used to establish the decrepitation rating of Western Australian iron ore showed scatter in results which could be reduced by textural type sampling. Testing of individual textural types resulted in separation.of a range of decrepitation behaviour patterns. No unique correlation was established between water content in goethite, or between any single mechanism and breakage in shock heating. The latter depends rather on several mechan- isms whose operation is controlled by the texture of the ore. Texture studies were used successfully to predict decrepitation behaviour which could be related to orebody structure for mine planning, and blending for sales or processing requirements.

Jan 1, 1973

By Hulton SJ, MacKenzie DH

The Broken Hill orebody within the leases of ZC Mines is still a major lead-silver-zinc resource after over 80 years of mining. It illustrates particular problems encountered in resource and reserve estimation in old mines. The six mined ore lenses are characterised by three features: ò complex external geometry, ò high internal grade variability, ò bimodal grade distribution. The high grade 3, 2 and 1 lenses and B lode have sharp external contacts but contain some low grade internal zones. By contrast A lode is of lower average grade and comprises an extensive but geometrically variable mineralised zone within which are numerous irregular bodies of high and medium grade ore. Geological factors are the main source of variability in reserve estimation, which historically has been conservative. For many years the geological resource tonnage has been maintained at a level sufficient to make up for extraction but at a gradually declining grade. Using a geological block cut off grade of 10% Pb + Zn the present in situ resource is 53.8 Mt grading 8% lead and 13% zinc. Using empirical cut factors a "recoverable reserve" is derived from this large geological tonnage. There is some doubt that the "recoverable reserve" is conservative enough to reflect mining reality. The most sensitive indicator of forthcoming change in total resource or insufficient drilling and development is given by changes in the tonnage and grade of possible ore from which the proved and probable categories are derived. Examples are given to show that where reserves are drill indicated, the delineation required for proved ore reserves must be enhanced to achieve final stope design. The move in recent years to greater emphasis on non entry mining and lower recovery of in situ material poses a dilemma for a mine which has practised 100% recovery for much of its past. The need for a realistic reserve assessment in current terms needs to be balanced against the fullest possible geological knowledge of the resource to cater for future technological developments.

Jan 1, 1987

By Hagen G, Uhlig H

In the Federal Republic of Germany the thermal environment in underground coal mines has deteriorated progressively over the past years. The number and capacity of refrigeration plants have increased correspondingly. In recent years high capacity spray coolers have been used in addition to conventional cooling coils.

Jan 1, 1988

In the first half of 1987 two four metre diameter raise bore holes were drilled at the Olympic Dam Project for ventilation purposes. The first hole, 476 m x 4.0 m diameter was completed in 96 days, 35 days longer than scheduled. The second hole, 407 m x 4.0 m diameter was completed in 39 days, 2 days ahead of schedule. Both holes were drilled with a Robbins 121R rig using a Wirth head that consisted of 23 face cutters and 5 side cutters, supplied by a contractor. After the sites were located a grouting program was carried out to help seal off an aquifer between 160 and 180 m below the surface. Cavities discovered in the Andamooka Limestone were filled with concrete. Because of the overlying dune sands and clay both sites were pre-sunk to the competent Andamooka Limestone.

Jan 1, 1988

Willemite mineralization was discovered in 1966 in the North Flinders Ranges of South Australia, in the course of a stream sediment sampling programme. Further work outlined a total of nine separate willemite occurrences in the Copley/Beltana area, and ten small deposits in the Toondana area south of Parachilna. Mineable reserves of 1 000 000 tonnes grading 36.8% zinc were outlined in three deposits in the Copley/Beltana area and campaign mining of the Main Orebody commenced early in 1974. The main group of deposits all occurred within red, dolomitized Cambrian Ajax Limestone, and most are associated with significant thrust faulting. The area of the Main Orebody group of deposits has been intensely fractured, and the surrounding dolomites are often brecciated and contain up to 5% zinc. Lead and arsenic mineralization are minor components of the main group of deposits. Masses of Middle Proterozoic Willouran Formation crop out adjacent to or close to most of the deposits in the Copley/Beltana area. The Willouran is frequently highly sheared, brecciated, and often contains large inclusions of younger formations. It is believed that most of the Willouran outcrops represent piercement structures.

Jan 1, 1975

Increasing use has been made of engineer ing geology and hydrogeology in the development of the infrastructure for mining projects. The Geological Survey of the Department of Mines, the Department of Main Roads, the Irrigation and Water Supply Commission and private consulting organisations and mining companies, employ spec- ialist staff to carry out engineering geological and/or hydrogeological investigations. Such in- vestigations have been of assistance in recent mining developments in northern Queensland, in- cluding those in the Cloncurry - Mount lsa, Weipa, Greenvale and northern Borten Basin areas.

Jan 1, 1974