Search Documents

By Knight J. L, Baker G

The Wonthaggi coalfield is in South Gippsland, about 90 miles southeast of Melbourne. It is situated on the down-faulted block of the South Gippsland highlands that lies south of the Kongwak fault, between the Powlett River and the sea (Fig. 1). The coal, which is of Jurassic age, occurs in two small, and intensely faulted, limnic basins, that lie on either side of a concealed ridge of Silurian sediments. The coal was first found as thin seams outc1'opping in the cliffs at Cape Paterson, but the seams that are worked at Wonthaggi are concealed beneath a veneer of Cainozoic sands that covers the Jurassic strata, and were found by boring.The c9al seams are worked by the State Coal Mine, which was opened in 1909 to ensure a supply of coal for the Victorian railways, following a prolonged strike in the Newcastle field of New South Wales. The total production from 1910 to June, 1943, amounts to 13,918,800 long tons of coal. The coal seams are faulted to a degree unknown in most coal...

Jan 1, 1944

By Savidis GM

This report outlines the experience of Australian mining operators in dealing with large falls of roof in advance of longwall supports. Previous and present techniques used for face stabilisation have been described, together with an analysis of [actors which contributed to the roof falls, in each case. Attention has been focused on the stabilisation technique used at Angus Place Colliery, where the face coal was successfully reinforced by injecting chemical foam into Lite fractured areas. Although considered to be one of the worst roof falls in the history of Australian longwalls (60 m in length and up to 10 in in height), it was subsequently possible to resume cutting in Longwall 9 two weeks after the foam injection. A preliminary schedule of work involving the 'strata replacement' method, is also discussed. It has been based substantially on experience gained with cementitious supports, principally by ACIRL and Monier Resources.

Jan 1, 1986

By Kay JR

In 1984 a new Regional Geological Mapping Program (RGMP) was commenced by the Geological Survey of Queensland (GSQ); the new program was in response to the withdrawal of the Bureau of Mineral Resources from regional mapping. Areas for mapping were selected in northern and south-eastern Queensland on the basis of potential for mineral discoveries, level of company interest, inaccuracies in the first edition mapping and interests of other organisations (government and universities) in joint projects.Geological provinces of particular interest in northern Queensland are the Hodgkinson Basin, parts of the Georgetown Inlier not covered by earlier BMR-GSQ mapping, Broken River Embayment, Burdekin Basin, Lolworth-Ravenswood Block, Campwyn Block and Anakie Inlier. The 1:250,000 sheets covering these areas of interest are shown in Figure 1 including those already completed, those in progress and those planned for future investigation.A flow chart showing the various phases for RGMP projects is shown in Figure 2. Data collection has two facets: (i) field recording and (ii) office work including air photo interpretation, study of company reports, literature research, petrography and various laboratory studies. Two main strands of information collected are represented by a data base and compilation sheets. Compilation sheets are generally at 1:25,000 scale and are available for purchase. The current data base is very fragmentary and can be accessed only by direct contact with the relevant geologist or via written reports. A more accessible field data base is in the process of being introduced this year; this field data base (REGMAP) is based on standardised data recording and computer storage.

Jan 1, 1986

Roof bolting with resin bonded bolts has been developed extensively in French coal mines. There are three aspects of this development: 1. The reason for and the care used in the development of roof bolting from use as a reinforcement in a classical arched roadway to use as the only support in roadways in ad- vance of the working face (the roadway being reinforced behind the face); 2. The problems encountered and studied, such as choice of boltable roadways and determination of the technical data in designing a roof bolting pattern; 3. Only because roof bolting has been controlled by safety rules, and especially by accurate measurement of strata behaviour, has this system of support been expanded aapidly in France since 1967.

Jan 1, 1971

It is a privilege for me to participate in this vitally important discussion of The Role of Governments in the Management of Resources. The distinction of my fellow participants is evidence that this event is a matter of extreme importance and attracts international attention. In the management of natural resources, government and private enterprise share awesome responsibilities for the economic well-being of nations. Mining and its relation to the prosperity of nations is almost as old as recorded history. Copper was being mined and extractive metal- lurgy practised at Timna in Israel's southern desert as far back as 4000 B.C., and the rich mines of Laurium not only saved the Greeks from Persian domination 2500 years ago, but also provided Athens with a monopoly of silver in the Mediterranean world. This bolstered the economic power of Athens and led to the golden age of Greek commerce and culture.

Jan 1, 1978

By Pradhan GK

Blasting is one of the most important operations involved in surface coal mining. The removal of over-burden waste in surface coal mines of India had experienced many improvements in terms of blasting, explosives selection, blast design, equipment selection, deployment. etc. Two case studies of very large surface coal mines have particular importance in their blasting operations. Both these units have been equipped with large capacity excavating machines, hauling units and also have some difficult mining situations. Blasting is done in benches in close proximity to human dwellings and over coal seams developed by underground methods with problems of high wall stability etc, as well. The various steps taken to improve the blasting operations ensure smooth operation of the equipment to meet the targetted coal production.

Jan 1, 1991

(Quality can be defined as that which is acceptable to the market and can be supplied with a predictable degree of uniformity and dependability at a low cost. The market for any mining product is downstream processing, whether it be an alumina refinery, a gold processing plant or a flotation plant. The cost of that downstream process is partly dependent on uniformity of its feed material both in physical and chemical terms. With more operations adopting procedures which require quality assurances in line with International Standards, from their raw material suppliers, miners must look to their grade control processes to provide uniformity and predicability.This is not a new concept. The mining industry has constantly been working with ahighly variable raw material supplied by Mother Nature, from whom we cannot demand quality assurances. Through the processes of exploration, resource and reserve definition, long and short term mine planning and day to day grade control an end product has been supplied which consistently meets our customers requirements, in an economic fashion. When any of these processes fail, then penalties are incurred which can range from increased mineral processing costs to loss of markets and in the ultimate case, failure of a mining operation.

Jan 1, 1992

By Walker E. R

IN the early age of steel it was made hy what is known as the cementation proeess, in which wrought iron was embedded in charcoal and heated in a mufflc furnace to a tcmperature of approximately 1100° C. for varying lengths of time, the length of time depending upon the amount of carbon (or better known in thosedays as the degree of hardness) required in the finished product.By this process the resultant product obtained was not of uniform quality, and because of this uncertainty of quality Huntsman was induced, in the year 1740, to introduee what is known as the crucible process.This process consisted of cutting into small pieces the product of the cementation process, placing these pieces in a crucible, and melting them down with the aid of a eoke-fired furnace, after which the molten metal was cast into suitahly shaped ingots, from which could be hammered any desired shape.A section of crucible furnace is shown in Fig. 1. By this means a product, very uniform in character, was produced.The process is still in use, but, owing to its high operating cost, it is mostly eonfined to the production of very high-grade carhon and alloy steels. Its position to-day as a producer of these high-grade steels is, however, being very seriously challenged by the electric process.It was owing to the excessive cost of crucible steels and the need of producing a steel in commercial quantities and at a reasonable cost, that led Sir Henry Bessemer to introduce what is known as the Bessemer process.

Jan 1, 1930

By Zhansen P

This paper describes the test re- sults which give a complete proccess of failure of concrete lining embedded in sand medium under load, including the order of appearance of crack along the lining up to failure. nor each crack appearance corresponding calculation being made to assess the redistribution of moment and thrust force in critical section including crown section, section making 45¦ with the vertical etc. De- flection at the above stated critical sections are also measured at each stage of loading. The pressure along the top hori- zontal surface of embedded lining and the vertical sides are measured by pres -sure gauges embedded in sand medium. fhe test results show a complete figure of rupture characteristics of concrete lining embedded in soft ground which approximates alluvial deposite often occur in metro construction at cities near the river side. These test results have been taken as a reference in assessing the action behavior of concrete lining in certain cities in China.

Jan 1, 1987

This paper deals briefly with productivity-enhancing advances in shaft sinking technology in South Africa post-World War II in general and the developments and application of long rounds since the 1980s in particular and is amply illustrated.It touches on the conversion to circular section, concrete lined shafts, the introduction of tungsten carbide drill bit inserts and grab lashing; expounds the rationale driving the development of longer rounds; and then describes the evolution of long rounds using hand-held and mechanically mounted rockdrills in South Africa and Canada by both local and foreign contractors. The recent experience gained on the sinking of the South Deep Main Shaft follows. Results obtained from this experiment are tabulated and commented upon. The paper concludes with the postulation of æwhat nextÆ and æwhere toÆ scenarios. Addenda include a list of shaft rounds in excess of three metres in length blasted in the Main Shaft at South Deep and their results, typical round design, manufacturerÆs specifications for the 6 m shaft jumbo and rock drills.

Jan 1, 2002

By Drain P, Dibdin T. R

THE completion of the Linda incline man and supply haft at the Mount Morgan Gold Mining Oompany's mine led to an investigation of the various safety gears in general use in mining shafts. One of these gears completely fulfilled the necessaryconditions. This paper endeavours to give a description of the man car and safety gears now operating in the before mentioned shaft, together with the main considerations leading to their design and sub equent adoption. Fig 1 diagramatically shows a longitudinal section of this shaft.

Jan 1, 1911

Digital computers, by virtue of their capacity for high speed repetitive calculation at low cost, are finding increasing application to routine calcula- tions in the mining industry. In this paper techniques are shown whereby the use of computers can be extended to more complex tasks. The regular calculation of grades and tonnages of material to be extracted from specified areas of an operating open pit is a necessary part of production planning. In this paper it is shown how these calculations can be carried out by computer. thereby freeing planning staff from manual calculation. An operating open-pit mine can be described in terms of drill logs, geological ore boundaries and pit perimeters at various levels. These form the data base which must be suitable for frequent updating to incorporate new information. A suite of computer programmes is described which operates on this data base to calculate tonnages and grades of ore within extensions to the perimeters as indicated to the system by planning staff. Possible future extensions are discussed.

Jan 1, 1971

By Bennet A. G

An overall review of the selection of rock strength and deformation characteris- tics for the design of the Melbourne Under- qround Rail Loop (MIJRL) rock tunnels is presented. Particular emphasis is placed on aspects of in-situ testing, including large diameter plate bearing tests. Material on the interpretation of test results for use in the design of the tunnel linings and openings is included, with a brief discus- sion of desiqn methods.

Jan 1, 1981

Two significant TBM boreability predic- tion models are outlined. Predicted advance rates are compared with actual advance rates taken from twenty case histories. The results show that a simple low cost method that uses one machine parameter and one rock parameter compares very favourably with a high cost sophisticated method which also includes information regarding discontinuities in the rock mass. The effect of rock texture on drillability is also examined. A method of quantifying rock texture has been developed and is outlined. Experimental results show that the developed TEXTURE COEFFICIENT returns highly statisti- cally significant correlations with drilla- bility data in a wide range of rock types.

Jan 1, 1987

By Ghiani M, Satta F, Zucca A, Peretti R

After a brief introduction on the principles of contact electrification and a synthetic illustration of the Turbocharger separator, the successful results obtained with different raw materials are given and discussed, with particular reference to a North African run-of-mine with carbonate gangue, a crude ore from India containing pyrite and a mineral sample from Angola having quartzeous gangue. The pre-eminent effect of target surface temperature in the charging device of the separator is emphasised. On the basis of the results of both batch experiments and long-run tests the prospects of industrial application appear very interesting both from the technical and economic points of view, even when compared with froth flotation.

Jan 1, 1993

By E Hogan, M Goodz, R Wright

The planning, permitting and monitoring procedures of the re-opening and rehabilitation of mine sites is an ongoing process which must continue throughout and beyond the life of the project. Both industry and government bodies must remain flexible to allow guidelines to be altered where and when necessary.To enable the successful re-opening of the Morning Star mine at Woods Point in alpine Victoria, many environmental and historical issues had to be evaluated.The site which had been derelict for 28 years had to be rehabilitated to a safe and aesthetically pleasing state prior to construction of a new operating mine site. Considerable liaison with government authorities and the local community was required.

Jan 1, 1992

The Coal Corporation of New Zealand Ltd (CoalCorp) is the largest coal producer in New Zealand, with extensive properties in both the North and South Islands. CoalCorp's North Island operations are kilcmetres to the south of Auckland. opencasts, are located in the catchment wildlife, historical and scenic values. in this catchment is the single most mining operations. centred on Huntly, a town some 80 Five coal mines, four of which are of Lake Waahi, a lake with significant The discharges of mine lodgement water important environmental constraint on Throughout New Zealand the use of water is controlled by a statute called the Water and Soil Conservation Act 1967. All industrial water users are required to hold Water Rights, which are in effect licences to take, use, dam, divert or discharge water. Water Rights are obtained through a legally defined process and any potentially affected party has the per to object to their granting. A special tribunal hears the evidence for and against an application, and issues its decision, which is reviewable in a higher court on Appeal. Rights, if granted, are issued subject to conditions and, in the case of mining discharges, limits would be set on flaw rate, suspended solids concentrations, turbidity, pH and the concentrations of any potential toxicants. This paper presents a case study of an integrated, catchment wide water management plan for Lake Waahi, that was prepared by the author, and others while the author was in the employ of CoalCorp, and its predecessor, State Coal Mines. The author is grateful to CoalCorp for their permission to submit this paper.

Jan 1, 1988

There has been a substantial transition in the minerals industry R&D environment in the last five to ten years. Changes have occurred in the client and contractor base, the sources and scale of funding, industry imperatives, and competition and collaboration between contractors. These changes are documented from the viewpoint of research contractors in general, and universities and the JKMRC in particular.It is concluded that research groups need to be more proactive in managing their interface with the industry. Both industry and the research community m\lst devote the resources and attention necessary to ensure the effective transfer of research results into operations. The Australian Minerals Industry Research Association (AMIRA) has an important role in these processes, and in regulating the balance between contractor collaboration and competition.

Jan 1, 1996

By Weller K. R, Stewart P. S B, Restarick C. J

The performance of the Renison tin concentrator was assessed in detail for two arrangements of the three available ball mills. With two mills used for primary grinding and the third for regrinding table tailing, the concentrator recovered 65.3 per cent of tin in the three tin concentrates produced by tabling, vanning and flotation at a calculated overall grade of 37.5 per cent tin prior to batch dressing. In the second arrangement one mill was used for primary grinding and two mills for separate regrinding of table tailing and sulphide concentrate. The metallurgical effective- ness of the change was somewhat obscured by unintended changes,i.e. an increase in the assay of the fresh feed from 1.38 per cent to 1.1+6 per cent tin and unresolved changes in the sulphide rougher flotation and tabling. However, using the results from a detailed size by size analysis of the behaviour of ore components in appropriate parts of the plant, it proved possible to show that, had the two unintended changes not occurred, up to 5 per cent

Jan 1, 1977

By Walker K, Burton RC

An outline of the ventilation and refrigeration requirements of deep South African gold mines is presented. This is followed by a brief description of the history of controlled recirculation in mines and the practical and economic benefits such schemes can offer. The potential hazard of a fire in a recirculation system is discussed.The major part of the paper describes the first large-scale field trial of controlled recirculation to be conducted in South Africa. Emphasis is placed on the monitoring system that was used for data acquisition during the trial, and also on a safety system designed to shut off the recirculation fans in the event of a fire.The paper concludes with a review of the latest development work taking place on recirc-ulation safety systems.

Jan 1, 1985