Search Documents

By M Goers, M Almond

"The use of reverse circulation (RC) drilling for grade control sample collection was selected by the Pueblo Viejo Mine Geology department at the recommencement of the operation in 2010. This method was selected because it allows: for multi-bench drilling (60 m hole depth, four benches of mining) to aid mine planning and provide a detailed close spaced drill data comparison with the reserve model angled drill holes to optimise the drill hole interception of the vertically controlled mineralisation dry sample collection in areas of excessive surface and groundwater mining operations to commence with the long assay return period (due to the need for the samples to be shipped overseas for analysis) until the on-site laboratory is operational.To date, 118 302 m of drilling has been completed throughout the operations of two open pits: Monte Negro and Moore. Two drill rigs (contractor and site-owned and operated) with three generations of sampling systems have been used to date. Throughout the drilling a 20 per cent quality assurance, quality control (QAQC) sample check (blanks, field duplicates and standards) have been used to check the drilling and laboratories performance. In addition, a total of 1104 fines samples were collected to compare the drill chip samples collected and the fines lost with two of the sample systems used.The drilling to date has highlighted the need for a complete and coordinated system to be used before sufficient confidence in the quality of the samples collected is achieved.The complete system must be set-up and coordinated to obtain the best quality sample possible. This complete package includes: drill bit size and shape for the rock being drilled and mineralisation targeted face sampling hammers with the correctly sized hammer shrouds sample hose routing to reduce sample flow turbulence and choking blow-down valves to eliminate drill hole water that has entered the drill string during rod changes correct drilling techniques targeting sample quality a sample system that captures the fines for inclusion into the sample.These improvements can be obtained without reducing the drilling rates.The measurements required to demonstrate the improvement in the sample quality will be the focus of future work within the department.CITATION:Goers, M and Almond, M, 2012. Bit to bag - The importance of a total coordinated system in reverse circulation drilling, in Proceedings Sampling 2012, pp 65-72 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By S Robinson, R Perkins, D Barrett, D Kepert, C Fowers

The discovery and delineation of significant mineralisation in the Eliwana region continues Fortescue Metals Group’s strong exploration success. In the decade after the first hole was drilled into Christmas Creek in mid-2004 a total of over 11 Bt of hematite-goethite mineralisation have been delineated supporting the raising of $13 B, construction of five mines, 620 km of rail and a five-berth port. As of June 2014, Fortescue was shipping at the rate of 155 Mt/a. The area including the Eliwana and Flying Fish deposits is one of a number of future growth opportunities that Fortescue is currently evaluating.The Eliwana and Flying Fish deposits occur on the south dipping limb of the Brockman Syncline/Jeerinah Anticline. The Eliwana group of deposits are hosted by the Brockman Iron Formation with the Flying Fish/Broadway group hosted by the Marra Mamba Iron Formation.Structurally the area is dominated by moderate southerly dips of the regional dome and keel style folding. The regional limb is locally cross-cut at a small angle by asymmetric north facing Ophthalmian folds trending 110°. These fold sets, in part, preferentially host subsequent supergene mineralisation. Faulting is only locally apparent.Early phases of exploration commenced in 2006, with mapping of Flying Fish and reconnaissance drilling in 2007. However, due to the concurrent discovery (Clarke et al, 2009) and subsequent fast tracked development of Solomon channel iron deposit and Firetail bedded iron deposit (Simpson et al, 2011) priority was placed on developing Solomon due to its relative proximity to existing Fortescue infrastructure. Staged follow-up drilling of both Marra Mamba and Brockman targets at Eliwana was progressively undertaken from 2008 onward.As of 20 May 2014 a total of 1494 reverse circulation (RC) holes for 54 248 m and 13 diamond holes had been completed, resulting in the delineation of a Mineral Resource of 740 Mt. Exploration via mapping, drilling and metallurgical evaluation of adjacent prospects continues with additional resources expected in the future.CITATION:Barrett, D, Perkins, R, Kepert, D, Robinson, S and Fowers, C, 2015. Geological setting of Eliwana and Flying Fish deposits along the north limb of the Brockman Syncline, Hamersley Province, Western Australia, in Proceedings Iron Ore 2015, pp 219–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S Hapugoda, H Han, L Lu

Charcoal produced from Syzygium Zeylanicum trees was widely used in ancient Sri Lankan iron smelting practices. Charcoal made from Syzygium Zeylanicum tree trunks, branches and leaves were analysed by optical mineralogy and SEM and found to contain unusually high concentrations of calcium oxalate (CaC2O4.H2O – CaOx) crystals in plant cells. Partial and full reduction tests of a high-P Brockman ore were conducted at several temperatures with coke and coke doped with CaOx and CaCO3. It was observed that CaOx promoted reduction and generated comparatively more metallic iron in reduced samples. Furthermore, CaOx encouraged phosphorous partition into slag phases than into the metallic iron, suggesting CaOx can a potential alternative fluxing material to calcium carbonate for treating high-P iron ores in ironmaking processes.

Sep 18, 2023

By R H. Knight

Uncertainty in prediction and modelling of geological (physical) ore continuity in geometrically complex ore deposits is a key risk factor in mining. Reducing geometric uncertainty of hard-boundary ore/waste contacts and related geological features improves the efficiency of local mineral resource estimation and reserve calculation, mine/stope planning, ore control and in-mine exploration. Detailed underground mapping of serial-level drives provides a continuous record of the characteristics and contact configuration of ore, as well as crucial ore-related geological features that are required to resolve geometrical variability when closely spaced drilling proves inadequate or is cost-prohibitive. The mapping-based approach described in this paper re-establishes the focus on the geology of the orebody by incorporating high-value, detailed geologic mine mapping information. Mapped ore-related configurations and relationships, recorded on a succession of faces or on a series of levels, provide the basis for 3D interpolation and extrapolation of the local geologic continuity of an orebody. Correlative points representing locations of key ore-related geologic features on each face or level are linked by 3D polylines or trajectories forming a coherent geometrical framework. The coherent progression of geometric changes mapped by these trajectories reveals the overall ‘dynamic’ of the geometrical framework, as well as the spatial tendencies of its geological constituents. Distinct sets of ore control trajectories are selected from within the framework and are used in the construction of alternative geological ore continuity models. As mining proceeds, alternative models are evaluated, and are then either refined or rejected. The geometrical framework is used to evaluate theoretical models and practical heuristics, focus exploration targeting and inform and guide all aspects of mine geology in active mines. This approach also lends itself to analysis of global ore continuity in the re-evaluation of mature or abandoned mines. Its use is particularly effective in geometrically complex orebodies such as the West Branch orebody and the orebodies of No 2 mine of the Balmat-Edwards-Pierrepont zinc district, which are used to illustrate the method. CITATION:Knight, R H, 2014. A mapping-based approach to geological continuity prediction using examples from the Balmat-Edwards-Pierrepont Zinc District, St Lawrence County, New York, USA, in Proceedings Ninth International Mining Geology Conference 2014 , pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By R Zhang, X Huang, M Zhou, X Lv, C Bai

Iron ore sinter accounts for a large proportion of blast furnace ferrous burden in Chinese steel mills. Depleting high-grade iron ore resources and spreading complexity of iron ores in mineralogy and morphology have made it more difficult to utilise iron ores efficiently and economically. In this paper, the physical properties of iron ore particles were characterised using mechanical sieving, laser sizing and gas adsorption. From those measurements, two physical indices (fractal dimension of the particle size distribution and surface morphological factor) are defined as important variables for optimising the granulation performance of iron ores. The moisture capacity and the contact angle of iron ore particles with water were also measured to determine the strategy of water-feed in the granulation process. It can be concluded from the experimental results that an increase in the fractal dimension of the iron ore particles will lead to a better granulation performance, while an increase in moisture capacity with a range of 12.8 ~ 14.8 per cent would increase the optimum water content where the granule packed bed achieves its best permeability. Furthermore, the optimum permeability varies inversely with the moisture capacity of the sinter mixture.CITATION:Huang, X, Lv, X, Zhang, R, Bai, C and Zhou, M, 2013. Iron ore characteristics and their application in optimising the granulation process, in Proceedings Iron Ore 2013 , pp 261-268 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By W Valery, A Jankovic

A growing demand within the minerals industry for sustainable development and the introduction of carbon taxes have resulted in a significant focus on improving the energy efficiency of comminution circuits. However, in this drive for improved energy efficiency the role of classification has been overlooked. Inefficient classification and large recirculating loads reduce circuit capacity, result in over-grinding and higher specific energy consumption.It is well understood that classification increases mill capacity; therefore, closed ball mill-cyclone circuits have become an industry standard. However, due to limitations in cyclone classification efficiency, the optimum recirculating load is limited to about 250 per cent. A simple relationship quantifying the effect of classification efficiency and recirculating load on grinding circuit capacity is presented in this paper. The possibility of improving the capacity of ball mill circuits by improving classification efficiency is discussed, considering the current practical limitations of classification equipment. Simulation tools were used to evaluate circuits with cyclones and with high frequency screens to identify opportunities to improve energy efficiency. The investigation also identified potential benefits to flotation recovery due to a reduction in over-grinding.CITATION:Jankovic, A and Valery, W, 2012. The impact of classification on the energy efficiency of grinding circuits - The hidden opportunity, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 65-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By C R. Fountain, R J. Sinclair

The zinc industry is dominated by the electrolytic zinc (EZ) process. The EZ process has a low tolerance for impurities, resulting in tight concentrate specifications. Many mining companies sacrifice zinc recovery in order to meet smelter specifications. Some have ore-bodies that cannot be economically developed because too much metal has to be sacrificed, or it is just not possible to meet the specification. The BUKA Zinc Process (BZP) has been developed as a method of producing high-quality zinc from a wide range of concentrates. It can have lower capital and operating costs than the conventional zinc and lead production routes. Advantages accrue from increases in metal recovery during concentrating, smelting and refining; the elimination of most of the capital and operating costs associated with lead smelting; reduced transport costs; lower zinc refining costs; reduced refinery residue disposal costs; and reduced future environmental liabilities. This paper describes results of testwork that has been undertaken to demonstrate the viability of the BZP on both test rig and laboratory-bench scale.

Jan 1, 1998

By R Norris, M Dunne

Substantial efforts by the industry, as well as by process and equipment designers, have resulted in many innovative developments that provide cost effective reductions in water usage. This paper showcases four emerging best practices in industry including examples of recent installations. Belt press filters are a small fraction of the operating and capital cost of alternative ædryÆ tailings technologies. This gives operators who must ædryÆ their tailings a competitive advantage and makes such operations much more sustainable. The new generation of belt filter presses use less energy, produces lower cake moistures and better disposal stacking properties. The need for tailings storage facilities may be eliminated or in some cases high-grade tailings can be dewatered and sold as a low value product. Mining applications include sand tailings, sinter plant waste, coal tailings and power station fly ash. Flip-flow screening machines are proven worldwide in the dry classification of coal and other minerals, reducing the size of beneficiation plants, whilst reducing energy, water demand and media consumption. They also allow the screening of wet/sticky materials not able to be sized using conventional screens. Lamella separators are used for toxic water clarification and/or sludge thickening in many downstream metal industries with the underflow often dewatered in a belt filter press. Such low cost, high capacity thickeners could also be used instead of conventional thickeners at smaller mines. The simple and reliable continuous washing upward flow (CWUF) sand filters have been used for treatment of waste water from coal preparation plants and steel works as well as in the production of potable water. The filtered waste water from mining processes can then either be reused or discharged from site. Other installations include cleaning mine water to prevent the blocking of dust suppression spray nozzles.

Jan 1, 2006

By T Raynlyn, J J. Campbell, R J. Holmes, J R. Manuel, S P. Suthers, A Poliakov

Prediction of the downstream processing performance of iron ore needs detailed information on mineral composition, textural peculiarities, particle density, porosity, mineral liberation and association and mineral grain size. Optical image analysis and automated iron ore texture classification systems are a way of obtaining such information. Furthermore, this information can be used for predicting the output of specific processes and their combinations. Several examples of the application of such an approach to process performance studies for iron ore are discussed. These include the application of classification by ore texture to modelling and optimisation of hydrocyclone performance, the effect of including textural information in modelling of sinter properties, and combining textural information with an experimental study of stirring and ultrasonic treatment of haematitic-goethitic iron ore fines to understand the deportment of fines and the breakdown/deagglomeration of particles. In all cases, the availability of textural information is important and helps provide a better prediction of process performance and/or understanding of the unit process.

Jan 1, 2008

By Greenwood-Smith R, Ellis W. K

A bulk analyser based on the gamma-ray resonance scattering process can be used to give a rapid and accurate measure of the percentage by weight of copper or nickel averaged over a large mass of sample, typi- cally 20 kg. It is shown that for a bulk sample containing about 3 wt.% Cu, crushing to -25 mm is the only sample preparation requited for analysis to within an error of about 0.06 wt.% Cu (errors quoted are one standard deviation). A comparison of bulk analyser and con- ventional assays on the same bulk samples can be used to estimate the sample preparation errors in the conventional methods. The squared deviations between bulk analyser and conventional assays are approximated by the sum of variances in sample preparation, conventional analysis, and bulk sample analy- sis. The sample preparation error was esti- mated as 0.26 wt.% Cu for samples crushed to -2 mm before splitting, 0.08 wt.% Cu for samples crushed to -0.35 mm before splitting, and 0.04 wt.% Cu for the average of 15 grab samples from bulk samples which had been crushed to -2 mm. The average copper grade for each group of samples was about 1.7 wt.%. Results are presented which show that

Jan 1, 1976

By Jarvis ST

Colliery spoil is the major constituent of colliery spoil 'rockpaste' which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpasle are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising mulling a 6600 nt' section of an abandoned mine was conducted prior to the mulling of the Littleton Street Mine which had a volume of about 500 000 m'. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully rued for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over I I mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

By O Bøckman, E Thisted, K H. Esbensen, U Thisted

Process industry measurement systems, once installed, are often interpreted as static black boxes delivering correct values as long as not proven otherwise. After first implementation and set-up with a distinct sampling frequency, they often run ‘forever’ without checking if this frequency is still appropriate with respect to changed raw materials characteristics, different process conditions or changed customer specifications. Failure detection is based on operator experience and skills (often close to an art form) and/or from control measurements of reference samples. This may well be too late for many industrial process contexts. An appropriate sampling frequency is a critical success factor for valid monitoring and control.Based on the methodology of variographic analysis we here illustrate how to design/re-design/optimise an industrial measurement system in terms of sampling frequency, discretisation and accuracy based on customer specifications. We also show how variographics can be used to monitor for deviations. We use experience from process industry to show how these methods can be used not only for product characterisation, but also for monitoring input factors, process indicators and measurement of these. The information hidden in the vast amounts of data that is continuously created in modern process industries can be utilised to cut costs in the measurement activities and at the same time contribute to early error detection. We illustrate by case examples from production processes at a nickel refinery, supporting the Lean and Six Sigma methodology. This will provide a standard operating procedure for monitoring the stability of measurement systems, and provide a basis with which to discuss how a variographic approach can be integrated with the Lean and Six Sigma approach as an online tool to map, characterise and validate measurement systems and thus avoid more cumbersome measurement system analysis in full detail.CITATION:Thisted, E, Thisted, U, Bøckman, O and Esbensen, K H, 2017. Variographic case study for designing, monitoring and optimising industrial measurement systems – the missing link in Lean and Six Sigma, in Proceedings Eighth World Conference on Sampling and Blending , pp 359–366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By D P. Blair

The theme of this conference is blasting productivity. This article only considers the technology aspect of this theme, and in particular, the collection and analysis of experimental data. In many cases, field trials are set up to collect data on variables such as fragmentation and vibration with the aim of comparing different explosive products and/or blast designs. An important aspect of such trials is the collection of sufficient data to draw sound conclusions. In this regard, there is no doubt that the scatter in real data is the root cause of all problems of obtaining misleading results due to an insufficient number of trials. This article shows that the typical one-off trial has a high probability of producing misleading information, which could be considered to be worse than having no information at all. Assuming that sufficient data has been collected, this article also highlights the methods that can be used to make the most of that data. These methods include the application of appropriate statistics that are dependent on the nature of the scatter in the data, and the use of some of the more recent filtering and spectral approaches that can be used to reduce the noise in measured blast signals and increase the resolution of their spectral characteristics.

Nov 8, 2011

Sishen uses a state-of-the-art tracking system to track material from its position in blast blocks through various stockpiles and crushers. Qualities are blended directly to the crusher as opposed to blending from stockpiles. This poses an interesting challenge to the planning department to simulate these conditions. The software used in these simulations are Whittle 4X and Maximiser for long-term planning, Xpac for medium-term planning and Mine Works Planner for short-term planning. Geological models and mine design layouts utilise Surpac. Sishen introduced Xpac a number of years ago; the system has developed and changed over the years. With the Sishen Expansion Project (SEP), which aims to utilise low-grade material, major changes to the planning process have to occur. SEP requires that the mine have two different plants, which utilise two different ROM feeds and have different beneficiation curves. Xpac is used to produce a rolling 18-month plan, which is as close to actual operations as possible. In order to do this, the simulations have to take into account the plants beneficiation curves, stockpile movements, hauling distance and equipment needs. On top of this, the schedule has to continually consider specifications for Fe and the contaminants. Plant yields also have to be kept within a certain bandwidth. Xpac is used to simulate the above parameters, as well as generate the raw data required to produce a mine budget. The paper will also show how the 18-month planning process and subsequent planning processes are measured and aligned. Xpac has proved to be an excellent tool to achieve these goals.

Jan 1, 2005

By W. M. LONIE

Address by the President of the Institute (Mr W M Lonie) in making the presentation of the Certificate of Honorary Membership to Sir Ian McLellan, K.C.G.M, K.B.E. Address by Sir Ian McLellan after accepting the award.

Jan 1, 1979

By S Long, D Carnovale, L Louwrens

The Mt Wright underground mine (MTW) is located near the town of Ravenswood in north Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited.The Mt Wright mine has gone through many stages, from the conception and implementation of the world first ‘sub-level shrinkage’ stoping (SLS) with continuous fill mining method in 2010, through to steady state production. These have been outlined in detail in papers presented by Mackay (2011) and Mackay, Long and Koen (2014) at previous Underground Operators Conferences.Since the last paper was presented, MTW has experienced significant change in two key areas.The first significant change was the discovery of a previously unknown hazard in the form of flat rilling events (FREs) from closed drawpoints (DPs). These events are believed to be unique to MTW and pose a significant risk to both the safety of personnel and the business as a whole. The paper will discuss this hazard and the evolution of the controls and practices that have been introduced to mitigate the risk posed by the identified hazards. The material involved in these events is extremely dry, fine and hot.The second significant change is an altered stress regime bought on in part by a change in the production front orientation and a general deterioration in ground conditions in some areas of the mine. This has caused some production interruptions at MTW. The second half of the paper will describe the challenges encountered, the mechanisms behind these challenges and the strategies implemented to safely return MTW production to planned levels.It is believed that other operations can learn from the issues mentioned above, and the paper has been written with this in mind.`CITATION:Long, S, Carnovale, D and Louwrens, L, 2017. Mt Wright – managing unique risks, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

Copper-Cobalt hydrometallurgy has seen a resurgence in recent years with the development of projects in Zambia and the DRC. Many of the flow sheets are unique in their use of hydrometallurgical techniques to improve performance compared to the older types in current use. The emphasis has moved from direct copper electrowinning/stripping, with multiple stages of precipitation for removal of impurities and concentration of cobalt, to innovative use of solvent extraction and ion exchange with higher cobalt recoveries to final product. The poor quality direct electro-won copper has been supplanted with solvent extraction-electrowinning; with consequent production of LME 'A' quality metal. Many of the precipitation steps in cobalt recovery and concentration, have been replaced with solvent extraction; while the remaining precipitation stages have been enhanced with use of oxidants to improve impurity removal. Operating experience from two of these circuits has shown the benefits of the new technologies and the improved overall recovery of both copper and cobalt into higher quality products.

Jan 1, 2008

Open pit mining at Bingham Canyon commenced in 1904 and about two billion tonnes of ore have been extracted since then. There remain just under one billion tonnes of ore in the pit and this will be mined by 2015. Because the porphyry system extends below the ultimate pit limits, Kennecott Utah Copper Corporation initiated a study in 1997 to determine the viability of underground mining. The study was initiated at that time because the results were to be used to compare the economics of a further pit expansion to that of an underground mine. If a pit expansion was viable then overburden removal would have to start in the near future. This paper is a summary of the work that was carried out for the underground study. Block cave mining was determined to be the most appropriate method to mine the deposit. Two block cave areas have been planned with a total production rate of 72 500 tpd. Additional sources of ore will come from skarn orebodies that are associated with the porphyry deposit. The geology of the deposits is described together with the geotechnical techniques that were used to characterise the rock in the absence of more detailed data that are normally available. A general description of the mine plan is given along with the reasons for selecting the particular methodology used. The study was completed at the end of 1998 and demonstrated the viability of underground mining at Bingham Canyon. Funds have been approved for further drilling and technical studies, which will lead up to a feasibility study in 2004/5.

Jan 1, 2000

By J L. Macdonald, G S. King

"The development of a predictive geometallurgical model is a multidisciplinary and iterative task that involves both discovery and integration aspects. In this paper, the authors discuss the concepts of geometallurgical modelling in terms of the underlying relationships that are used to connect geology, metallurgy and economic value, and how the early-stage preparation of a spatial geometallurgical model enhances project value and provides a sound basis for future studies and test work programs.Hot Chili’s (copper-gold-molybdenum) Productora Project, which is located in northern Chile, is a porphyry-copper style deposit that can be exploited using open pit mining and preparation of a saleable concentrate from fresh ore, as well as heap leaching, solvent extraction and electrowinning (SX-EW) extraction of copper from oxide ores. To enhance project value in the Productora prefeasibility study (PFS), Hot Chili developed a geometallurgical model that was used to predict the process responses of both sulfide and oxide ores. The Productora model incorporates test results from mineralogical, metallurgical and comminution testing, as well as other studies completed on a suite of samples collected from the many geological domains of the deposit.Using Bond Work Index and Abrasion Index proxies in the geometallurgical model, Hot Chili estimated the variability of sulfide ore throughput and comminution costs. Heap leach acid consumption in oxide ore was estimated from drill hole calcium concentrations. The model was then used in mine scheduling to identify high and low throughput or high and low acid ore zones so that the processing of these zones could be advanced or deferred to improve net present value (NPV). Additionally, the cost benefits of preparing an early-stage geometallurgy model were quantified through a comparison to a conventional model that was based on test work averages.CITATION:King, G S and Macdonald, J L, 2016. The Business Case for Early-stage Implementation of Geometallurgy– an Example from the Productora Cu-Mo-Au Deposit, Chile, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 125–134 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S Harrison

Work health and safety duties around Australia include duties to manage psychosocial health and safety (mental health) of workers engaged by businesses or undertakings and of other persons impacted by the operations of the business or undertaking. Persons conducting a businesses or undertakings must develop systems of work and policies and procedures for ensuring, so far as is reasonably practicable, the safety and health of workers and other persons. Officers have a duty to exercise due diligence and to ensure effective systems are developed, implemented and resourced. The developed systems will only be effective with worker’s co-operation and engagement. The duties placed on workers by work health and safety laws are an important part of the safety matrix of obligations. Supervisors and Leaders are workers and they play a critical role in delivering health and safety outcomes. To deliver these health and safety outcomes with respect to psychosocial safety Supervisors and Leaders need to understand their obligations and have a framework to use to assist them in understanding what workers require and what steps need to be taken to meet their duties. They also need to take steps to assist those workers that they supervise to meet their duties.

Apr 16, 2024