Search Documents

By P Chapman, B Moosapoor

The objective of this paper is to present the potential applications of geostatistical analyses in planning CPTu investigations, as well as interpolation of CPTu data. The paper presents a case study of a geostatistical analysis of CPTu data undertaken between 2004 and 2017 for an upstreamraised TSF located in the Goldfields region of Western Australia. An initial model is developed using the 2004, 2009 and 2017 CPTu data. The model is used to predict in situ cone tip resistance (qc) measurements, as the interested primary variable, at the selected locations where 2019 CPTu were undertaken, and the results of the prediction and the actual data are compared.

Jul 1, 2021

By B Crompton, A Berghorst, G Knox

Laboratory-based dynamic testing provides an invaluable tool in the development of rock bolts for use in highly stressed, burst prone rock masses. While in most cases the laboratory-based test method is not a direct comparison to an in-situ installation due to the purely axial loading and variations in boundary conditions, it does provide an indication of the performance of the tendon system under dynamic loading. The aim of the research described in this paper is to provide an understanding of the effect of the impact velocity of the impact mass during a laboratory-based dynamic test. Understanding the effect of boundary conditions of laboratory testing will improve Geotechnical Engineers understanding of the performance in an in-situ installation. In addition, due to the limited number of dynamic test facilities, an understanding of the effects of the boundary conditions will aid in the comparison of test results for different products from different test facilities. The research was conducted using an impact tester, whereby a known mass is raised to a known height defining the kinetic energy and velocity of the mass at the point of impact with the test sample after release. The impact velocity was varied between 2.7 m/s and 5.4 m/s, while the kinetic energy of the mass was maintained at 11.5 kJ. While a correlation between the impact velocity and strain rate of the system tested was established, due to the properties of the system tested, the range of impact velocity on which dynamic tests were conducted was insufficient to result in a considerable change in the average impact load, the cumulative proximal displacement and the cumulative maximum energy absorbed over multiple impulse. However, due to the reduction in the momentum of the impact mass the impact duration and displacement during each impulse in the series of impulses reduced. CITATION:Knox, G, Berghorst, A and Crompton, B, 2018. The relationship between the magnitude of impact velocity per impulse and cumulative absorbed energy capacity of a rock bolt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 160–169 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Lyons, S Baker, D MacHunter, D Pepper

Mineral processing plants require a storage buffer to bridge differences in production rates between mining and processing. Where coarse ores are processed, such as coal or hard rock, this buffer may be an ore stockpile or silo. For wet-mining processes, eg dredging or hydraulic mining, or where fine ores are slurried close to the mining face, a surge-bin is used to contain the plant feed and smooth out the variations in mining rates. These bins have gradually evolved from simple storage vessels to units that are now frequently part of the mineral separation process itself, such as providing a desliming function to remove deleterious ultrafine gangue. This feed conditioning is often essential to achieve the levels of plant performance required in times of declining ore grades and or where inherent ore characteristics make separations harder to achieve. To achieve these dual roles requires careful consideration of bin design factors such as geometry and lining selection and increased use of instrumentation and advanced, or remotely supervised, control systems. All this ensures they provide capacity to smooth out variations in mining rates and guarantees that when conditioning ores or adjusting slurry densities ahead of the plant it is achieved without loss of valuable minerals. This paper examines the evolution of the modern surge-bin from a simple, so called, constant density tank with its inherent mass-flow compromises, limited feed preparation and beneficiation abilities, and footprint penalty, to a current state-of-the-art surge-bin, the LFCU, with a control system which provides demonstrable steady outputs, while conditioning and in some cases beneficiating the ROM material and all from a highly compact unit. It further discusses their use in other applications around the world, for example providing the necessary security for long distant high-density pumping systems; constant high density, low water usage, tailings disposal pipelines and high capacity ultrafine iron ore beneficiation.

Aug 24, 2022

By B J. Beven, A Vatandoost, J Young, S Campbell-Hardwick

The intrinsic value of iron ore depends on its physical and chemical characteristics. For example, silica and alumina are unwanted elements, downgrading iron grade and adversely affecting high temperature processing, attracting penalties in smelter contracts. For this reason, an informed knowledge of processing characteristics and product quality of the ore is valuable and cost effective during mine planning and processing.Ore variability is a significant factor that affects metallurgical behaviour and efficiency of ore processing equipment. Ore of sufficient chemical and physical quality needs to be modelled, mined, processed and usually blended. Feed and product assays are commonly used to assess potential ore upgradability. However, assays alone cannot be all informative of actual processing response given the variability of the physical properties of the ore.This study investigates the potential benefit of implementing a geometallurgical approach during the commissioning stage of the Kings deposit, part of the Solomon Iron Ore project in Western Australia. Kings drill hole database information, ie geological, textural and geochemical data, together with the results of metallurgical test work were used for geometallurgical analysis and modelling. Three main ore types were identified at Kings, namely channel iron deposit (CID), bedded iron deposits (BID) and Detrital Iron Deposit (DID). Additional classifications were utilised to better characterise these units in terms of their physical properties.Bulk sampling for each ore type was carried out across the deposit for metallurgical testing. Multivariate statistical models were developed for prediction of product quality for each geometallurgical unit. A new approach for modelling yield based on ore upgrade factors is introduced. These models were then applied to the Kings regularised mining model to assess product quality across the mining blocks and to plan product stockpiling and blending strategies.CITATION:Vatandoost, A, Beven, B J, Campbell-Hardwick, S and Young, J, 2013. A geometallurgical approach for iron ore product evaluation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

As Pliny commented two millennia ago, The only certainty is that nothing is certain. Despite the many breakthroughs, advances and promises, the way we each live and work remains awash with technological, economic and political uncertainty. The resources sector is no exception in this regard. Mining itself is much more than a complicated process or recipe; it is a complex adaptive system. The way we adopt and adapt new technologies, the way we evolve data into corporate wisdom, the way we make decisions and even the way we view our concept of rationality should each be the subject of intense review. Translating these sentiments into sustainable company growth is indeed the challenge. This is unlikely to be achieved within convention, but through innovation. The game is changing!

May 1, 2010

By M D. Griffith

Oct 12, 2022

By A Fitzpatrick

An integrated and dynamic water balance and water quality model for a proposed base metal mine has been created using the GoldSimÖ software package. The model was initially developed to address the water quality of the Tailings Management Facility pond and how pond discharge would potentially affect downstream water quality. However, due to changing project objectives, the modelling has expanded over time through an iterative process to encompass the full mine site and all receiving environment water quality. The model results have been used as part of the mine planning/design process but are also intended to be used for the environmental impact assessment and permitting process. The model has been built to allow for changes to input terms to be readily made as additional data becomes available. The model results serve as a prediction of water quality and the potential project impacts to the receiving environment water quality. This paper presents the process by which data from a wide variety of sources was used to construct the model and how the model results were used to guide development of a conceptual water management plan. In addition, the role of the model in establishing proposed discharge criteria will be highlighted. The model has been delivered as a fully functional application with the intent that the end-user can be other than the modeller, the development of this aspect shall also be covered. CITATION:Fitzpatrick, A, 2012. Predictive site-wide water quality modelling as a tool for mine planning and permitting - A recent Canadian example, in Proceedings Life-of-Mine 2012 , pp 71-78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

Slide presentation at conference

Jan 1, 1996

A hidden asset in most exploration and mining activities is data. Common practice involves the spending of large amounts of money to discover, define and prove the viability of a mining project. Some organisations have used operations research analysis and internal costing methods to allocate a value to their data and to compare the costs of data maintenance to other more tangible activities like plant and equipment maintenance. Those organisations, which do not undertake such an analysis often, have little knowledge or understanding of the extent and the worth of their data. Often the organisations lack of knowledge and understanding of the data is indicated by their failure to fully exploit or realise their opportunities. The focus of this paper is to discuss new technologies that optimise the management and security of collected and derived data. The technologies discussed are components of the software systems acQuire and MineSight.

Jan 1, 1999

The development and distribution of gold placers in Otago û Southland is related primarily to the evolution and architecture of three distinctly different drainage networks that developed during and since Gondwana breakup: +        Late-Gondwana û Pre-marine; +        Middle Tertiary Post-marine; and +        Modern. Late Gondwana û Pre-marine drainage was dominantly recti-linear and controlled by normal faults and sedimentary basins formed before or during Gondwana breakup. Placers formed dominantly in 2nd order transverse drainages with primary sources in their catchments. This drainage network was progressively destroyed by inundation and burial by marine strata during Late Cretaceous û Middle Tertiary marine transgression that ultimately covered most of New Zealand. Middle Tertiary Post-marine drainage evolved on and incised the newly emergent low-relief landscape during regional marine regression driven by development of the present plate boundary through South Island. Most of Central Otago was drained into Southland and to the southern coast via a large braided river system with an extensive network of tributaries in its Central Otago reach. East Otago was drained by several smaller systems. Placers formed dominantly in proximal and medial reaches of 1st and 2nd order drainages with primary or pre-existing placers in their catchments. This drainage network was destroyed by inundation and burial of the Central Otago reach of the major system by lacustrine strata following tectonic damning of its middle reach by range uplift and development of a lake complex that covered >5000km2 of Central Otago. The Modern drainage network evolved from the Middle Tertiary network through complex response, firstly to uplift of NW-trending and NE-trending ranges throughout the region since the Late Miocene, and secondly to the effects of major Pleistocene glacial advances in West Otago. Placers formed in alluvial fans at range margins, proximal and medial pre-glacial fluvial systems and glacial outwash sequences. Evolution of each of these drainage networks has been accompanied by widespread sedimentary recycling of alluvial gold from older to younger placers, augmented locally by input of first-cycle gold derived from erosion of primary sources in the repeatedly exhumed basement rocks.

Jan 1, 2006

For more than 15 years after the Northparkes orebodies were first discovered in 1976, the project was delayed by the need to find an economic way of mining the low-grade E26 deposit. The decision to use a low-cost block caving method to mine the orebody was made in the early-1990s; but the project's future did not solidify until 1993 when a radical new approach was adopted which sought to integrate business imperatives with technology and organisation strategies. The approach led to the establishment of a strategic vision which tied together all the components that could have a major impact on the project, to provide a framework for guiding strategic choices. The strategic vision strived to break away from the old rules of how mines are organised and operated; and involved finding imaginative new ways to radically redesign mining processes to achieve quantum leaps in performance.

Jan 1, 1997

By J Rubio

This work presents design features of an innovative in-line mixing helical (coiled) reactor for flocculation and flotation as a solid-liquid separation process for suspended particles (including liquid droplets). The device has been named flocs generator reactor (FGR), a compact system whereby the flocculation of particles is assisted by the kinetic energy transfer from the hydraulic flow through the reactor and/or by the injection of microbubbles (30 - 70 ¦m). The flow mixing presented a plug flow regime with a low dispersion degree, promoting the required hydrodynamic conditions to disperse the polymer flocculant (cationic polyacrylamide) and to generate æstrongÆ flocs of Fe(OH)3 or clays (as colloidal model systems) with aggregation using an anionic polymer, Al2(SO4)3 and poly aluminium chloride (PAC), and oil emulsions destabilisation with a high molecular weight cationic polymer. The solid-liquid separation of the flocs was then achieved either by settling or by flotation with microbubbles. This paper discusses advances in this new in-line flocculation-rapid flotation device to remove æaerated aggregatesÆ, aggregates with entrained and entrapped bubbles. Studies were carried out with different models of FGRs (varying the length:volume ratio) and process efficiency (mainly kinetics) evaluated as a function of polymer concentration and some operating parameters, namely, feed flow-rate, air:solids ratio and residence time. Results showed that the aerated flocs are readily floated with rising rates in the order of 120 mh-1, values higher than those obtained for the settling of the non-aerated flocs (18 - 24 mh-1). The FGR requires short residence times and generates dense, well structured flocs (with a mass fractal dimension, dF of about three) which withstand high shear forces. Mechanisms involved appear to include small bubble formation and their rapid occlusion (entrapment) within flocs, nucleation of bubbles at floc/water interfaces, polymer coiling as a result of æsalting outÆ effects at the aqueous/air interface and plug flow type of mixing (flocculation). Successful examples of emulsified oil and solids removal from water are shown and because in all cases high efficiencies were obtained (>90 per cent removal). Due to the high process efficiency and high loading capacity shown, the FGR appears to have good potential as an in-line flotation-separator device in applications requiring high rate solid-liquid or liquid-liquid separations.

Jan 1, 2005

By P Moynagh

"A plan is critical but on its own it is a bit one dimensional, the three dimensions critical to success over the long-term, through changing economic, geological and management conditions are:the quality of your planning an ability to see and adapt to change a disciplined continual improvement/learning system.This paper will examine how a number of major Australian resource companies have used a commitment management system to connect the ‘theory’ embodied in plans (whether mine, project, maintenance or training plans) and immediate reality ‘practice’ as experienced by supervisors and their crews in the workplace. This paper draws on management theory embodied in management operating systems (MOS), Lean, Theory of Constraints and Six Sigma approaches to continuous improvement and a good dose of real world experience. It is embodied in the statement: ‘successful organisations are driven by a series of commitments that people make to each other and deliver on’.Citation:Moynagh, P, 2016. Everyone Has a Plan Until They Get Punched in the Mouth – Creating Trust, Commitment and Results in Tough Times, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 293–299 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By C F. Stokes

The Trident Gold Deposit has been successfully developed by Alacer Gold (formerly Avoca Resources Limited) into a 1.3 Mt/a operation in the space of four years from discovery to first gold pour (2008). The current in situ Resource for Trident is estimated to be 5 900 000 t @ 5.0 g/t for 940 000 ounces at a cut-off of 1 g/t or 2 g/t depending on ore style. Production to date (Alacer and previous owners) is in excess of 500 000 ounces. The deposit lies towards the southern end of the Norseman-Wiluna Greenstone Belt in the Archaean Yilgarn Craton, where it is centred on the historical Higginsville Mining Centre, midway between the world class gold centres of St Ives (+15 Moz) and Norseman (+6.5 Moz). Trident is hosted primarily within a thick, weakly differentiated gabbro with subordinate mafic and ultramafic lithologies and comprises a series of north-northeast trending, shallowly north plunging ore zones. The deposit comprises two main mineralisation styles; large wallrock-hosted ore-zones comprising sigmoidal quartz tensional vein arrays and associated metasomatic wall rock alteration (Eastern Zone, Western Zone and Apollo) hosted exclusively within the gabbro; and thin, lode-style, nuggety laminated quartz veins (Athena and Artemis) that formed primarily at sheared lithological contacts between the various mafic and ultramafic lithologies. The initial interpretation of the Trident Deposit was based on steeply-dipping structures controlling the zones of mineralisation, with much of the targeting and drill-testing aimed at this style of orebody. Subsequent exposure of the orebodies has identified a series of shallow-east dipping mineralised systems (interpreted to be large reverse shears) that at their intersection with the steep-dipping structures cause significant gold enrichment. It is postulated that both orientations are primary fluid pathways with the intersection between the two resulting in zones with significantly high concentrations of gold mineralisation (in excess of 300 000 ounces). This new understanding on ore controls at Trident has identified that the thin lode-style shear-hosted laminated veins are continuous for over 1700 m along strike as they step en echelon down-plunge. In addition, a repetition and periodicity to the intersection between these steep dipping lode-style systems and the shallow-dipping mineralised zones (estimated to be 700 - 900 m down-plunge) has been identified which has considerably increased the down-plunge potential of the Trident Deposit.

Aug 22, 2011

By M Jones, G Corder, A C. Keith

"Sustainable development has become an issue of ever increasing importance to the mining industry. The Ernst & Young (EY) mining industry risk radar regularly shows several sustainability elements in the top ten risks, with social license the number three risk in the 2014/15 survey. This is supported by the Fraser Institute survey results of 2013 showing that 36 per cent of responding companies indicated public opposition had affected their permitting and approvals process.Addressing these issues in a strategic way across a mining business that is then translatable to actions at operational level has remained an elusive goal in the industry. In addition the environment and community issues are commonly viewed as somewhat separate from financial and production issues and as a compliance cost rather than a value add. In their Harvard Business Review paper of 2011, ‘Creating Shared Value’, Porter and Kramer outline changes in thinking required for companies to improve their business sustainably through considering the societal issues impacted by their operations and products. Along the lines of ‘doing more with less’ companies’ value chains can be redefined to reduce energy, transport, water or other resource usage leaving additional resource for societal usage and/or reducing environmental impacts. This paper explores the linking of the holistic Five Capitals-based approach with the creating shared value (CSV) concept to help businesses unleash the benefits of innovation. Previous papers have demonstrated the potential for Five Capitals approach to create strategic value through sustainable development. Building on previous work, this paper provides an overview of the current status of holistic approaches to mine management and presents the application of the CSV concept on an African mine currently undertaking capitals-based strategic planning. The paper also demonstrates the value that has been created through utilising this approach and proposes improvements for changing the way the industry tackles and delivers benefits related to sustainability issues.CITATION:Keith, A C, Corder, G and Jones, M, 2016. Strategic sustainable development – creating shared value in the mining industry, in Proceedings International Mine Management Conference, pp 249-264 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 22, 2016

By T Peters

The Kibali Gold Mine is currently comprised of several open pits, a 3.5 Mtpa underground mine and a 7.5 Mtpa processing plant. Development of the underground operation commenced in December 2012, with initial access established through twin surface declines, followed by the commencement of a blind sink 8 m diameter rock hoist shaft in March 2013. Stope production started in December 2014 with ore and waste trucked to surface. The 755 m deep blind shaft sink was completed in August 2015 together with the cutting and equipping of three main station levels. Two of these levels provide access for the establishment of the underground materials handling system as well as the main dewatering system for the mine. This paper covers the process of determining the optimal location of the Kibali hoisting shaft relative to project-specific critical factors, and then focuses on the design and implementation journey associated with the off-shaft development that essentially encompasses the Material Handling System (MHS) for the mine. The journey starts from the findings of the previous owners Feasibility Study (FS), a subsequent Optimised FS, followed by detailed engineering through to implementation. It was identified during implementation that a significant change in the designed off-shaft layout was required following detailed underground geotechnical and hydrogeological investigations. In addition, the paper provides details on the MHS performance since commissioning to steady state, and on key learnings relating to the overall project process.

Mar 29, 2023

By J H. Zietsman

The transition to more sustainable metal production is receiving much attention at present, and the iron and steel industry is at the centre of the conversation. New, more environmentally friendly production technologies, such as direct reduced iron (DRI) smelting furnaces, need to be developed in a short period of time. This necessitates increased use of computational modelling that incorporates more accurate material descriptions. The combination of large-scale multiphysics models of high-temperature processes with CALPHAD material descriptions leads to infeasible computation times. This can be resolved with the previously reported RapidThermo framework, which has been demonstrated to make equilibrium calculations orders of magnitude faster, within controllable limits of accuracy. In this paper, we explain how further material properties, which are important to modelling hightemperature reactors, can be added to the RapidThermo framework. This can improve the accuracy and usefulness of process and multiphysics models in the development of new technologies, which can significantly accelerate development cycles.

Aug 21, 2024

Intrusion related Cu/Au mineralisation is localised in Pacific Rim island arcs by arc parallel, termed accretionary structures; or arc normal, termed transfer structures. In Papua New Guinea, NE trending transfer structures, evident on Landsat imagery, represent deep crustal fractures which have facilitated dextral rotation of the mainland during oblique plate collision. Major structures localise intrusion centres, and by rotation, develop ore hosting dilational environ-ments in subsidiary structures. While transfer structures localise the Porgera, Wafi and Yandera porphyry centres, the Frieda Porphyry and associated Nena high sulphidation Cu/Au mineralisation are localised by accretionary structures. The Bulolo Graben, which hosts the Morobe Goldfield, developed during intra arc rifting aided by movement on transfer structures. Crustal thinning has initiated magmatism with which diatreme breccias and fracture controlled mineralisation are associated.

Jan 1, 1994

By B Hannah, M Uriarte, F Labarca, C Madore, G Ganapathi, L Martin, T Haase

BechtelÆs Mining and Metals projects across the globe are executed in remote arid and semi-arid countries where providing even basic water supplies impose considerable challenges. Opportunities for water conservation measures using a Six Sigma initiative were proactively pursued to address the potential business impacts of limited availability of water resources. The initiative investigated areas driving water-optimisation during concrete operations and camp management. This paper details the water conservation evaluation of alternatives and cost/benefit analysis based on current and predicted water usage for development projects. Optimisation of water consumption through institutionalising more prescriptive standards for camp design and defining water conservation requirements have resulted in a new standard specification. Based on our projected mining project workload across the globe, it is estimated that for the period 2012 - 2015, a potential 5.5 M m3 water savings resulting in US$11 M could be realised for construction camps and savings of 4 M m3 of peripheral concrete process water resulting in potential cost savings of US$8 M could be achieved as a result of these revised standards.CITATION:Haase, T, Hannah, B, Ganapathi, G, Martin, L, Madore, C, Labarca, F and Uriarte, M, 2013. Water conservation at construction projects, in Proceedings Water in Mining 2013 , pp 251-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

The Earth Moving Equipment Safety Round Table (EMESRT) was established by mining companies in 2006 to influence manufacturer's equipment design through a process of engagement. 2010 EMESRT member companies include Anglo American, Barrick, BHP Billiton, Centennial Coal, Collahausi, Newcrest, Newmont, Rio Tinto, Vale and Xstrata.Driven by a persistent need for retrofits to new equipment, such as haul trucks, EMESRT initially engaged with Surface Equipment Manufacturers including Caterpillar, Komatsu, Leibherr, Hitachi, Le Tourneau and Terex. These OEMs responded positively to the EMESRT initiative, welcoming the opportunity for dialogue with an aligned industry regarding human factors issues related to equipment design, rather than needing to respond to the disparate range of demands for design modifications previously received from individual customers. This engagement process is about making global sustained changes within the OEM organisations and within the mining companies. It is a very international exercise. For example, over two weeks in September 2010, a total of 21 different miners from ten different companies travelled from Australia, South Africa, Canada, Brazil, Singapore and the United States to engage with OEM counterparts who assembled from the United States, Japan, France, Sweden, Finland and Germany. EMESRT Surface Group representatives completed a whirlwind tour of the major North American manufacturers of mining equipment. Starting in Dallas (Atlas Copco, LeTourneau), this tour passed through Gainesville (Sandvik), Newport News (Liebherr), Guelph - Ontario (Hitachi) and Milwaukee (P&H Mining/Joy Global; Bucyrus), before winding up in Peoria, Illinois (Komatsu, Caterpillar). Over nine meetings, this group engaged with 129 individuals from nine OEMs. The EMESRT group welcomed miners from four non-member companies to come along for the meetings. These companies are Syncrude Canada Ltd, the Kearl Oil Sands Project - Imperial Oil (ESSO), Suncor Energy Ltd and Teck Resources Ltd.Other mining industry sectors have now expanded the EMESRT scope from surface mining to include exploration and underground mining equipment. In 2009, EMESRT was organised into four Technical Groups, consisting of EMESRT member company representatives, to focus on engagement with OEMs of surface, underground coal and soft rock, underground hard rock, and exploration drilling equipment. An advisory group has been formed to coordinate activities between all workgroups and provide strategic direction and cohesion between all activities. The Minerals Industry Safety and Health Centre (UQ-SMI) facilitates and coordinates all EMESRT activities on behalf of member companies. Building on successes with individual Surface Mining OEMs, EMESRT now aims to help OEMs in their transition to a sustainable design process that will incorporate and address specific design philosophies at the concept phase of design, so that significant improvements can be made up front for little cost within the overall budget. EMESRT members plan to educate all stakeholders, internally, within their own companies, and externally, by addressing industry associations, regulators and other end users about new ways of evaluating equipment design based on EMESRT purchasing specifications. This presentation will outline the EMESRT approach and report on progress in 2010.

Dec 6, 2010