Search Documents

With a price slowly rising above US$35 per ounce gold became a mineral worthy of prospecting and mining endeavour in the early to mid 1970s. Fortune therefore appeared to smile onNew Zealand with its favourable geological environment for gold and past record of major gold production from both hard rock and placer deposits. This was a particularly welcome development as the post war years, including both the base metal exploration boom of 1967/1971 (which produced major nickel, iron and bauxite mines in Australia) and the earlier period of uranium exploration failed to produce any mines in New Zealand with the exception of the small Tui Mine and iron sand mining. Whilst hard rock mining now appears imminent it is 15 years further along the track since the 1967/1971 exploration boom and eight years since the upsurge in prospecting for gold in 1978. New Zealand still has no hard rock base or precious metal mining. This is not for want of proven or potential gold mining situations for these clearly exist at Waihi, Monowai Reef, Golden Cross, MacRaes Flat and elsewhere.

Jan 1, 1986

By G Baird, M Seto

Reliable evaluation of in situ stress is an important phase in the analysis and design of underground excavations, particularly for evaluating the stability of underground structures to prevent failure or collapse. A technique for the estimation of the full stress tensor based on acoustic emission (the Kaiser effect) is being developed and trialed at the WA School of Mines. The result obtained compare well with the standard over-coring method. The advantages of the technique are that it is relatively cheap, non-time consuming and is applicable to in situ stress measurements at depth in remote regions.

Jan 1, 2002

The design of a mine should aim to optimise the market value by maximising revenues whilst minimising costs. In open pit mining, the nature of the extraction technique translates this objective into the maximum recovery of reserves while minimising waste extraction subject to technical, economical and safety constraints. Since the introduction by Lerchs and Grossman, in 1965, of a model that is now considered a classic in the area, open pit design has reached a level of maturity and acceptance by industry. These models are being used on a regular basis by designers and planners.This paper proposes a new alternative model for open pit design. It is based on genetic algorithms (GA) and exploits a reduction of the number of decision variables of the more traditional techniques. The novel approach provides more flexibility than traditional models; it can also be extended to consider planning problems that traditional open pit design models are not capable of handling. The algorithm has been designed for two dimensional problems and tested in a simple instance. The results obtained in this simple test are encouraging and are a good supporting argument for the development of a GA model capable of handling three-dimensional (3D) instances. The model presented in this paper is just a first step towards a full GA to solve the pit design problem and it is believed that novel tools like the one presented herein could become great allies in tackling challenging problems in open pit design, an illustration of such a challenging problem is presented and discussed.

Dec 6, 2010

A New Online Detection Method for Arsenic Minerals in Process Streams

Sep 13, 2010

By C Bailey, T Kojovic, M M. Hilden, M S. Powell

The Julius Kruttschnitt semi-autogenous grinding (SAG) mill model was developed by Leung in the 1980s and extensively updated to the variable rates model by Morrell and Morrison in 1996. Since then only minor upgrades have been incorporated in the version distributed in the JKSimMet simulator. A number of improvements, developed over the course of the AMIRA P9 project and in recent independent work, have now been incorporated. These improvements are based on a power-based model that directly relates the degree of breakage with energy consumption. The new size-dependent breakage function has been incorporated. The upgrades include more accurate predictions for a wide range of mill fillings (ten - 40 per cent), slurry hold-up in the mill, pebble discharge rate and the influence of changes in feed size and ball load.The paper presents the status of progress in the model development. The upgraded model will greatly enhance its application to challenging design and optimisation studies required to optimise the performance of SAG milling circuits.CITATION:Kojovic, T, Hilden, M M, Powell, M S and Bailey, C, 2012. Updated Julius Kruttschnitt semi-autogenous grinding mill model, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 71-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S L. Birch, M D. Raven

X-ray diffraction (XRD) is a well-recognised, invaluable tool to provide detailed mineralogical analysis on a wide range of applications. However, despite the wide use of XRD in many industries, there are currently few recognised standard methods for quantitative XRD analysis and none for the analysis of iron ore materials. An initial step towards preparing a standard method for XRD analysis of iron ores was to assess the current level of precision achievable by practitioners of the technique by organising an international round robin. Six Australian chemically certified iron ore reference materials were distributed to over 100 international participants. A summary of over 120 data sets from more than 80 participants is presented. Results show that a bewildering array of techniques for sample preparation, data collection, phase identification and quantification were used. The reported values for the main components (ie hematite, goethite, quartz and amorphous content) show not only extensive variability between participants but also within participants’ results for those who submitted multiple data sets. The disappointing low level of precision exhibited for a relatively simple mineral phase system indicates a strong requirement for development of a standardised procedure.CITATION:Raven, M D and Birch, S L, 2017. Summary of results of an international X-ray diffraction round robin for mineralogical analysis of iron ores, in Proceedings Iron Ore 2017, pp 599–604 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Beneficiation Studies of Dolomitic Rock Phosphate in Pursuit of Zero Waste Technology - A Case Study

Sep 13, 2010

Avoca Resources LimitedÆs Higginsville Gold Project has a resource base of over 1 300 000 oz of gold. The Trident underground mine, which forms the basis of the project development, has a resource base of 927 000 oz of gold. Avoca is building the Higginsville Gold Project based on a minimum ten year vision, producing over 150 000 oz per annum. The project development has taken less than three years from the Trident discovery hole in October 2004 to the first ore production in June 2007. This paper discusses the background work associated with the development of the Trident underground mine in a difficult period for new project development in Western Australia. The resources boom, led by the iron ore industry in the Western Australian Pilbara region, is creating cost pressures and, combined with a lack of people and equipment, is placing cost and timing stress on a small developing project. Avoca Resources has developed a project execution management strategy aimed at mitigating cost blow outs and schedule delays.

Jan 1, 2008

By A M. Suchowerska, J P. Carter, J P. Hambleton

"In order to effectively predict the roof collapse of underground openings using continuum models, it is imperative that a realistic failure criterion is used to represent the rock mass. However, for coal mining operations, there is still uncertainty as to the appropriate failure criterion that should be used for the coal measure strata. This study compares stability numbers and collapse mechanisms for a rectangular underground opening predicted based on three commonly used failure criteria: the standard Mohr-Coulomb, Mohr-Coulomb with a tension cut-off and Hoek-Brown. Three methods of analysis are considered: an analytical upper bound method an upper and lower bound finite element formulation the displacement finite element method.The theoretical results are also compared with field measurements of subsidence above longwall coal mining. For the standard Mohr-Coulomb failure criterion, the friction angle governs the shape of the collapse mechanism, and the so-called critical width (the cavity width above which failures extend to the ground surface) ascertained from field observations in the New South Wales coalfields corresponds to a friction angle of approximately 30°. On the other hand, predictions obtained based on the Hoek-Brown failure criterion consistently overestimate the critical width. The results also show that tensile failure governs the stability of the cavity and shape of the collapse mechanism when a tension cut-off is introduced for the Mohr-Coulomb yield criterion.CITATION:Suchowerska, A M, Hambleton, J P and Carter, J P, 2014. Prediction of roof collapse for rectangular underground openings, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 367–374 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

Development of the Boleo Process Flow Sheet and the Direct Solvent Extraction (DSX) Circuit for Cobalt and Zinc Recovery The metallurgical process designed to treat the El Boleo Cu-Co-Zn-Mn ore involves a sulphuric acid leach in seawater under oxidative and then reductive conditions to maximise metal extraction. Copper and cobalt are recovered as cathodes by electrowinning, zinc and manganese as zinc sulphate monohydrate and high quality manganese carbonate, respectively, by precipitation after a number of separation and purification stages. One of the key purification stages of the Boleo metallurgical process is the CSIRO DSX circuit. The DSX circuit was developed using the synergistic solvent extraction (SSX) technology. Initially, a synthetic solution was studied, and by adding 0.4 M LIX63 to 0.5 M Versatic 10 in Shellsol D70, large synergistic shifts were obtained for cobalt (?pH50 4.24) and zinc (?pH50 1.62). After a single contact, the separation factor of metals over manganese reached over 6,000 for cobalt and over 380 for zinc, indicating excellent separation of cobalt and good separation of zinc from manganese, magnesium and calcium. The SSX system was further optimised with the modified synthetic pilot plant solution. The extraction of cobalt and Zn after a single contact was 93 per cent and 70 per cent, respectively, while the Mn concentration in the loaded organic solution was only 0.28 g/L. A proof of principle pilot plant operation was conducted in 2004 and a demonstration pilot plant for final engineering design in 2006 with outstanding performance of the DSX circuit. For the demonstration pilot plant, the overall recovery of cobalt and zinc exceeded 99 per cent with a raffinate containing only 4 mg/L Zn and 1 mg/L Co. The DSX organic system showed no sign of degradation during the pilot plant operation, indicating good chemical stability under the anticipated commercial operating conditions. The DSX circuit will be implemented in the future Boleo processing plant.

Sep 13, 2010

Recovery of Rhenium from Mineral Raw Materials of Kazakhstan

Sep 13, 2010

By R Castedo, P Segarra, I del Castillo, L M. López, J A. Sanchidrián

This work investigates some suggested methods for blast vibration monitoring on a hard surface based on 53 tests on a vibration exciter. Errors in the measurement attributable to coupling have been described as function of frequency by the rock-to-mount (or coupling) transmissibility, ie ratio of the velocity of the vibration sensor mount to the velocity of the rock motion. Transmissibility has been measured from 2 to 200 Hz, at two vibration levels (5 and 20 mm/s), in four seismographs. Attachment methods with an anchor, thermal adhesive and gypsum plaster allow stiff rock-to-mount coupling. They ensure accurate measurements (errors below 0.3 dB) for frequencies commonly found in blasting (below 100 Hz) irrespective of the mount characteristics and the vibration level. Free laid mounts and sandbagged vibration sensors lead generally to a poor, weak coupling. Errors are non-linear errors with the input velocity, ie the operating frequency window narrows as the velocity of the ground increases. Free mounts follow ground motion acceptably well (error up to 0.4 dB) at both vibration levels and frequencies below 15 Hz. At higher frequencies, free mounts lead to the largest distortions with expected errors ranging from 0.8 to 6.6 dB. Sandbagging limits the expected errors below 1.3 dB, but it does not prevent large errors that can be up to 4.5 dB. Both frequency and velocity should be considered together to assess the measurement errors instead of the expected accelerations, as it is currently made.CITATION:Segarra, P, Sanchidrián, J A, Castedo, R, López, L M and del Castillo, I, 2015. Effect of vibration sensor mounting method on the quality of vibration measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 545–552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

It is proposed to consider a new access, mining and hoisting system for underground deposits, as an alternative to the commonly used decline or vertical shaft access. The proposed system offers fundamental improvements in gathering of exploration data, reduction of capital expenditure and significant savings in mine operating costs. The cost reductions are achieved through:superior orebody definition by Supersucker winzing on ore prior to the commencement of capital development; considerable reduction of capital development in waste; full capitalisation on all benefits of a raisebored excavation; introduction of rubber tyred skip and rubber tyred Mine Rapid Response Vehicle; introduction of simplified ore handling system and reduction of underground mobile diesel fleet; and introduction of minimum maintenance shaft concept. The system is applicable to deposits ranging from shallow, low dip angle, narrow vein, high-grade to bigger, massive type vertical mineralisations accessed from the surface, preferably from the bottom of an open pit; it is also suitable as a down dip extension of an existing underground mine. The system is highly conducive to mine automation and emerging trend aimed to increase the ratio of mined metal/mineral to mined waste. It offers substantial reduction in diesel exhaust gas emissions to the mine atmosphere.

Jan 1, 2000

By D Wiseman, D Weedon, T Akroyd

Models of the size specific processes of particle collision, attachment and detachment have been combined in a form suitable for analysis of a full-scale flotation plant. The model is based on a first principal approach to particle collection by bubbles. Parameters considered include particle size, bubble size, particle contact angle, energy dissipation, entrainment and froth recovery. Using data structures configured within an Excel spreadsheet using æLimn: The Flowsheet ProcessorÆ, the model has been incorporated into a description of the individual cells within a simple roughing and cleaning flotation circuit. Simulated feeds of varying particle size distribution, feed tonnage and varying mineral hydrophobicity representing different mineral phases are presented to the model to produce predicted final concentrate grades and recoveries. Practical techniques for measuring many of the parameters included in the model are now becoming readily available. However, relating the terms included for contact angle, energy dissipation, entrainment (ie water recovery) and froth recovery to measurable parameters in operating plants remain as continuing challenges for research.

Jan 1, 2004

By Q Qu

Reliable prediction of longwall gas emission sources and rate plays a critical role in mine ventilation and methane drainage capacity planning. Over the years, Australian longwall mines have been using the historic Winter method and the Flugge method in modelling specific gas emissions (SGE). The predicted results often experience high discrepancies from the operational reality. To improve gas emission prediction, post-mining gas contents were measured in several mines in Qld and NSW by safely drilling core holes into the longwall goaf. The results revealed many new insights into gas emission characteristics from different coal seams and the drawbacks of the European methods in their use in high-production gassy Australian longwall mines. Based on measurement data, a new, time-dependent gas emission prediction model has been developed. Considering several factors such as caving, desorption and production rate, the new model can predict more accurate and meaningful gas emissions to meet today’s needs in mine gas emission management. A case study is provided to demonstrate the application of the new SGE model.

Oct 12, 2022

The New Zealand Minerals Industry is small but growing. Over the next 10 years it will be facing stiff international competition for skills to support this growth, particularly from Australia who are forecasting that a further 70 000 people will be employed by 2015.   The value of commodities mined and quarried in NZ continues to increase; and the value of coal, metals and industrial minerals production reached $1.505 billion in 2006, an increase of 15 per cent on 2005. Production increases will continue à. Latest Crown Minerals statistics show that national prospecting and exploration expenditure rose to $29.9 million in the year ended March 31 2006 û an increase of 46 per cent from the $20.4 million spent in the March 2005 year. The equivalent 2001 year expenditure was only $2.48 million.   The industry already experiences difficulty in recruiting the people it needs with ongoing demand for skilled underground miners, trades people, and mining professionals. This discussion paper will outline the national context with regard to labour, skills and training. It will suggest options and provide an opportunity for conference participants to discuss the way forward.

Jan 1, 2007

By L Lorenzen

In this paper, we developed and implemented a fuzzy logic expert system capable of evaluating the degree of sustainability within the context of gold mining operations. The newly introduced approach of evaluating sustainability in the gold mining industry has the merit of sufficiently handling diverse, sustainable, development-related qualitative and quantitative data owing to fuzzy logic technology capabilities in dealing with linguistic syntax. The economic, environmental and social indicator inputs were independently evaluated and then combined with the aid of fuzzy logic to provide an overall sustainability index on a scale of zero to one. A total of 66 independent indicators were identified and applied in our model. The novelty of this work lies in providing a coherent numerical and automated approach in evaluating sustainability in the context of gold mining operations. In addition, the model can aid policy- and decision-makers in arriving at consistent decisions regarding the degree of sustainability on various aspects of gold mining operations. The functionality of this model will be illustrated through several examples.

Jan 1, 2007

By N Clarke, R Dineen, W Jones

The Mt Lyell copper mine in western Tasmania has discharged acid drainage (AD) into the Queen and King Rivers and Macquarie Harbour for over a century. Presently, dissolved copper loads of about 1000 tonnes per annum and dissolved aluminium loads of >2000 tonnes per annum are contained in the AD, which is derived from underground workings (~60 per cent) and historic waste rock dumps (~40 per cent). Flows vary from about 100 L/s during dry periods, to >400 L/s during the wet winter. The site is presently operated by Copper Mines of Tasmania (CMT) who are not responsible for the acid drainage generated from the mine site. Although western Tasmania is famous for its mining history, tourism and aquaculture have emerged as the new industries on the West Coast, with a major tourism railway (the Abt) recently opened along the banks of the Queen and King Rivers. The emergence of these industries in a æclean greenÆ Tasmania has resulted in a strong community and government push to remediate the acid drainage. Remediation investigations and efforts at Mt Lyell were initiated by the Department of Primary Industries, Water and Environment (DPIWE), previously known as DELM, in 1995, and have included the quantification of environmental impacts arising from the AD, and the investigation and costing of potential remediation options. A primary focus of the work has been to identify cost-neutral options which recover metals from the AD in a saleable form to help defray on going treatment costs. This paper summarises these activities in generally a chronological order, highlighting findings of the program that are potentially applicable to other acid drainage sites.

Jan 1, 2003

The theme of my address to your Institute, indeed its name, is "The Mineral Industry - What Next?" Knowing that I was required to make four appearances, and not wanting to be too repetitious, I wrote a rather long speech of which I will deliver various sections at different places, with a common introduction. Specific areas I have addressed are "Exploration", "New sources of minerals and energy", and "Mining and metallurgy of the future".

Jan 1, 1984

New Bio-Adsorber with Activated Carbon and Nano Tube Carbon for Separation of Nickel and Cadmium

Sep 13, 2010