Search Documents

By D C. Grant, D J. Goudie, E Baird

The Scanning Electron Microscope – Mineral Liberation Analyzer (SEM-MLA) laboratory, as part of the Core Research Equipment and Instrument Training (CREAIT) network of laboratories at Memorial University, NL, Canada, has recently published efforts towards increasing the throughput of automated mineralogy systems by producing single-step trans-vertical moulds, rather than traditional 30 mm polished epoxy moulds. Due to the small particle size of iron ore grains in the -200 mesh size fraction (<75 µm), not all of the surface area on a mould is needed for measurement in achieving good statistical representation. In a new study, trimming of the excess area of a mould results in a smaller sample and increases the quantity of unique samples that can fit in a newly designed trans-vertical adapter for a FEITM MLA 650 field emission gun (FEG) scanning electron microscope. The complete analysis, using a newly designed sample block holder capable of holding 98 samples, required 57 hours of running time where each sample had an average of 33?400 particles measured and identified. The analysis was calibrated to allow for off-line discrimination of hematite/magnetite. The calculated Fe-assay values derived from MLA results were compared to those from bulk sample chemical assay. This shows the Fe assay having a correlation coefficient of >0.99 when the particle count is greater than 20?000. This study represents the most expedient method yet reported to prepare well-polished samples and analyse them in a timely manner that can allow for quicker results in process mineralogy.CITATION:Grant, D C, Goudie, D J and Baird, E, 2017. Analysis of individual - mesh iron ore samples in a single Scanning electron microscope automated mineralogy session, in Proceedings Iron Ore 2017, pp 535–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By S Jokanovic

At New Zealand Steel MiningÆs Waikato North Head operation a Bucket Wheel Excavator û shiftable conveyor mining system is used to excavate titanomagnetite bearing sand and clay. The system utilises two Bucket Wheel Excavators and two Beltwagons with a two shiftable bench conveyors and two common trunk conveyors to deliver material to a processing plant. The original system was commissioned in 1984 as a high capacity, low cost method of excavating. In 1996 a second Beltwagon was purchased, increasing the flexibility of the mining system.

Jan 1, 2002

By R G. Barker

The NZ Minerals Industry Association has continued to advance the interests of the minerals sector through leading the establishment of a Minerals Industry Advisory Committee, and the preparation of a technology strategy with funding assistance from the Foundation for Research, Science and Technology. The current moves mirror those of more than 30 years ago when a government initiative led to a resurgence of exploration through amending the mining legislation, redirecting Government research priorities and tax changes. The economic and political and commercial environment in 2001 is very different from that of the 1960s and success of these new initiatives depends on the continuing support and involvement of all sectors of the minerals industry, and building an improved relationship with the Government and the public.

Jan 1, 2001

Generation and Attachment of Submicron Size Bubbles to Colloidal Solids

Sep 13, 2010

Over the past few years, there has been an emerging relationship between business and civil society, especially NGOs. This relationship has the potential to bring about significant change, identifying common ground between commercial and societal interests. The mining industry has been a leader in acknowledging the need for community consultation and engagement. This paper argues that partnerships can make a very significant contribution to the industry as it comes to terms with the dilemma of an open economic system pushing against a closed ecological system.The paper will pose a number of questions: where is the locus for debate about sustainability in the mining sector?; how well embedded within companies are the new competencies that Leon Davis first identified in 1995 for the mining sector?; how has education for mining engineers or exploration geologists changed to prepare people for what are very different expectations within the working environment?; how well is the industry doing in managing its own environmental impact and what is its responsibility to an agenda for sustainability which extends beyond its own operations?;and how can NGO partnerships contribute to more sustainable outcomes? The paper does not aim to answer these questions, but to explore them in the hope that the issues and possibilities raised will contribute to advancing progress towards sustainability within the industry.

Jan 1, 2002

By G B. Arehart, J L. Mauk

Quartz veins from the Martha Hill epithermal gold-silver deposit, Waihi, commonly exhibit crustiform banded textures. Visual differences observed between bands are primarily the result of a 1 to 1500 ¦m variation in quartz grain size. Quartz band textures are dominated by anhedral interlocking quartz mosaics, commonly associated with minor adularia and sulphide phases; these textures are interpreted to be products of amorphous silica crystallisation. The occurrence of rhombic adularia suggests that prolonged boiling influenced parent fluids. In contrast, the presence of coarsely crystalline bands, made up of subhedral to euhedral quartz grains, infers primary crystal growth from solution; evidenced by the occurrence of growth-zoned quartz within these bands. There is a narrow range of 3.3ë in d18Oquartz between maximum and minimum isotopic values for the deposit. Significant overlap in d18Oquartz values are observed between the Martha and Welcome lodes. However, statistically significant and commonly systematic differences do occur between individual bands analysed in most samples. Temperature fluctuations may be the dominant factor responsible for observed inter-band variation.

Jan 1, 1995

Particle Mechanics and the Design of Cyclone Tribochargers Triboelectric separation is a dry electrostatic technique that has shown promise in several particle processing applications. A tribocharger uses contact or friction to differentially charge particles of different materials, which are then separated by an electric field. The initial tribocharging process is poorly understood, with tribocharger design and operation largely a matter of trial and error. A better physical understanding of tribocharger operation would therefore be of immense value in the optimisation of triboelectric separation processes. A combination of charge measurements, trajectory modelling and high-speed video has been used to relate charging to particle mechanics in a cylindrical pneumatic cyclone, one of the most effective tribochargers for mineral separation applications, and the preliminary results are presented here. The consequences of these observations for cyclone tribocharger design and operation, and for tribocharger design in general, are discussed.  

Sep 13, 2010

By D F. S Natusch, R J. Hooper

Recent lignite investigations indicate their potential as a strategic long-term fuel resource. This potential however would be determined not only by lignite quantity and quality, but also by economic, physical and social resources required to support it. The following discussion uses the example of a typical lignite mining operation to review the major resource requirements. While recognising that the implications of supplying those resources may be as important as their actual existence, this paper has purposely omitted such discussion as this will be one of the main target areas for the next phase of investigations.

Jan 1, 1983

Clinoptilolite as a Low-Cost Solution to Remove Heavy Metals from Water in Mining and Mineral Processing Industry

Sep 13, 2010

By R Kerrich

Early-Archaean (3.26 Ga) volcanogenic massive sulphide (VMS) deposits located within the low strain and sub-prehnite-pumpellyite metamorphic-grade Strelley greenstone belt, East Pilbara, Western Australia, contain exceptionally well preserved sulphide textures which are directly analogous to those of sulphide chimneys formed by black smokers at present day submarine hydrothermal vents. The VMS deposits are associated with seafloor alteration zones in and below silica-carbonate laminites, at the top of tholeiitic to calc-alkaline intermediate and felsic rocks. VMS mineralisation comprises stratabound Zn-rich sulphide lenses with significant Cu and barite, and variable Pb and Ag, above Cu-rich stringer zones, all of which are similar to Phanerozoic polymetallic or Kuroko VMS deposits. Sulphide-sulphate mineralisation implicates hydrothermal discharge into sulphate-bearing ocean waters, ruling out a globally anoxic Archaean hydrosphere. The volcanic rocks and co-magmatic sub-volcanic intrusion hosting the VMS deposits are characterised by the conjunction of LILE>LREE>HREE, and Phanerozoic La/Yb with negative normalised anomalies of Nb, P and Ti, consistent with derivation via subduction zone hydrous metasomatism fusing the mantle lithosphere.

Jan 1, 1995

The Golden Cross mine is a Joint Venture between Coeur Gold New Zealand Limited, as Manager, and Viking Mining Limited. The mine is targeting Zero Lost Time Accidents as a goal.   The Golden Cross operation produces gold and silver from both underground and open pit. The mine is based on an epithermal gold-silver deposit. Treatment of ore is on a campaign basis for each ore type (i.e. underground or open pit). Milling is conventional SAG Mill and Ball Mill grinding circuit followed by carbon in pulp recovery of gold and silver. All tailing materials are treated through the Cyanisorb process to reduce cyanide levels prior to being discharged into the tailings dam.

Jan 1, 1995

By N E. Whitehead

An application to mine an ilmenite-rich sand deposit in Westland led to public concern about potential radioactive hazards should the ore be further processed to recover zircon or monazite. A review recommended that any material involved in the heavy mineral sand industry containing more than 0.05% thorium, uranium or their mixture should be considered a radioactive substance and, for mining purposes, a notifiable product. Safeguards for those occupationally exposed would operate via the Radiation Protection Regulations. The major safety requirement would be the minimisation of dust in certain operations.

Jan 1, 1993

Technical Challenges in the Flotation of Molybdenite from Porphyry Copper Ores

Sep 13, 2010

The Golden Cross mine commenced production in December 1991. Both open pit and underground mines produce 1000 tonnes of ore per day. Mining techniques are discussed along with results and variations to proposed methods of extracting the ore.

Jan 1, 1992

By K Niyomjinda, B Etschmann

Chatree Gold Mine is currently the only modern day gold mine operating in Thailand, and is situated approximately equidistant from Chiang Mai in the north and Bangkok in the south. Environmental guidelines set by the Thai authorities require Chatree Gold Mine to achieve a Total Cyanide level of 20 ppm or less in the process plant discharge slurry stream prior to release into the tailings storage facility. This paper describes both the initial difficulties faced in achieving compliance on this limit utilising the conventional INCO SO2/Air cyanide destruction system and the subsequent process improvements initiated to both the leaching process and the standard INCO process to achieve the current compliance levels of approximately 99/100 shifts. Improvements were focussed on the dual aspects of reducing the formation of WAD cyanide and ferrocyanide species in the leaching circuit coupled with process changes to improve removal of the ferrocyanide species from solution during the cyanide reduction stage.

Jan 1, 2004

By P Wigley

New methods of analysing and modelling flotation circuits have been developed as part of the AMIRA P9 mineral processing research project. A study using these techniques was conducted on the Olympic Dam copper flotation circuit to provide the following outcomes: an estimate of the flotation cell hydrodynamic properties and froth performance characteristics, and identification of potential areas for improvement; an estimate of the feed floatability parameters for basic model development; and identification of potential flotation circuit improvement opportunities. A flotation circuit model of the Olympic Dam copper concentrator was developed using the data collected from mass balanced site surveys, along with hydrodynamic data, froth performance data and numerous laboratory batch flotation tests. The simulator that has been developed from the model has the ability to estimate the influence of selected changes (such as circuit changes) on flotation circuit performance. Several stream destination simulations were conducted to provide guidance for further testwork and possible circuit improvements. The results from these simulations are presented.

Jan 1, 2003

Comparison of Grinding and Liberation Processes for Stalky Biomass Materials as a Prerequisite for Production of Energy Pellets with High Calorific Value Pelletising biomass, especially straw and stalky materials, requires a product specific size reduction and liberation. However, moisture content plays an important role in palletising and also affects the energetic properties of the biomass. The paper illustrates the characteristics of the mentioned type of biomass and specifies the necessities for production of energy pellets. Defined requirements for biomass energy pellets will be shown based on relevant standards. The work focuses on a comparative investigation of the straw fibres after grinding with hammer/impact mill and after the liberation of the straw fibres with twin-screw extruder (two different communition units). A traditional hammer mill as well as an hydrothermal process taking place in a twin-screw extruder were utilised. Results of the grinding and liberation of rye and wheat straw fibres are discussed based on a detailed particle characterisation (particle size and shape distribution). Besides high calorific value the main pellet quality parameters are mechanical stability, abrasion resistance and further combustion technical characteristics. The particle size distribution displayed optimum characteristics for the combustion processes to be carried out in a furnace. The durability of the pellets produced from straw fibres liberated with twin-screw extruder was comparatively better then that prepared with the straw fibres after grinding with impact mill. Particle size distribution, abrasion values and the strength characteristics showed a good correlation with each. The high presence of N and S would result in high NOx and SOx emissions, where as the high concentrations of Cl would corrode the furnace. These chemical properties of the straw would restrict its usage in small scale furnaces.

Sep 13, 2010

In March 1990, Heritage Mining conducted a 2000 line km high resolution aeromagnetic survey of all its prospects in the Coromandel Peninsula. One of the areas covered was the Onemana Peninsula, situated about 5 km north of Whangamata. Details of location and geology are given by Robson and Stevens (this volume).   The detailed helicopter-borne magnetic and radiometric survey over the Onemana area consisted of 163 line kmÆs of flying, and was carried out in order to assist in the definition of hydrothermal alteration and pre- or post- mineralisation structures. The line spacing chosen was 100 m, flown east-west, with a mean sensor terrain clearance of 80 m. Tie lines were flown north-south every kilometre for levelling purposes. The sensor was a Geoinstruments G-813 proton precession magnetometer in a towed bird, with data recorded using a Geoinstruments G-2000 acquisition system.   The Onemana alteration system is at the northern end of a major north-north east trending structural corridor defined by regional aeromagnetic surveys performed by AMOCO in 1980 (Rabone, 1991). T his structure hosts a number of other extinct hydrothermal systems including Karangahake and Golden Cross. In the Onemana contour plot the predominant north-northeast structures form the boundaries of a large area of subdued magnetism in the southern part of the surveyed area that is caused by intense hydrothermal alteration. This area is about 3.5 km long by 1 km or more wide and contains outcropping sinters and hydrothermal eruption breccias, as described in Robson and Stevens. A number of other structures transect this alteration zone, with strike directions ranging from northwest to north. A northwest feature notably truncates the zone to the south, while the northern end seems to be simi1arly bounded; however as data coverage ends at the coast, this feature is less conclusive.    Two distinctive types of strongly magnetic rock were discernible the contoured data. The strong negative magnetic anomalies the north and west are caused by fresh negatively magnetised rhyolites. This was confirmed by ground follow-up work that showed the rocks to be fresh biotite rhyolites with high magnetic susceptibilities.

Jan 1, 1991

Study on Mineral Processing for a Cassiterite Ore in Southwest China

Sep 13, 2010

By C J. Hogan

Increasing demand for fine grinding to improve mineral liberation and metal recovery and the need for stricter control of the environmental impact of tailings deposition poses problems for tailings disposal. This has led to an increasing number of investigations of properties of tailings and their disposal. This paper describes laboratory model testing undertaken on Macraes mine flotation tailings to provide information on tailings behaviour under conditions of subaerial deposition. The in-place density or 'dry density' of the impounded tailings and the impoundment depth relationship are important for utilisation of the available impoundment storage facility and results of dry density to depth relationships are given for the Macraes mine tailings impoundment.

Jan 1, 1993