Search Documents

By N McKenzie, E Taylor, S V. L Barrett, H Lagger, A Purwodihardjo

This paper discusses the temporary support design methodology for the largest road caverns ever built in Australia—the Lutwyche Caverns—part of the Airport Link project in Brisbane, Australia. The Lutwyche Caverns with a maximum excavated span of 27 m form a key component of this major road project, allowing on and off ramps merging with the underground highway. In addition to the two large span caverns, a 15 m soft ground tunnel with 5 m cover above the caverns and two 24 m deep burial chambers for the 12.4 m tunnel boring machines (TBMs) had to be built in record time at Lutwyche.The temporary support design methodology involved the use of a range of analytical approaches, including empirical methods to provide a starting point for design development, key block models to determine the potential influence of discontinuities on excavation stability and 2/3D continuum and discontinuum models to determine the potential influence of adjacent excavations and the proposed construction staging on the design. In addition, probabilistic analysis of potential kinematic instability using a discrete fracture network (DFN) approach was also undertaken to establish the critical block loads for the temporary lining, while the continuum and discontinuum models were used to design the support for the 1.5 m diameter rock pillar at the north end of the northbound cavern.The numerical modelling was undertaken in close conjunction with the contractor to develop the optimal construction sequence, considering the available construction equipment on-site and the overall project program requirements. Part of the presentation will further show the applicability of the developed design during construction (deformations, monitoring field observations) and lessons learned for future cavern construction in Australia.CITATION:Lagger, H, Purwodihardjo, A, Barrett, S V L, McKenzie, N and Taylor, E, 2014. Temporary support design for the largest road caverns ever built in Australia – the Lutwyche Caverns, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By B Twidle, D Bertoldi, J Meikle, R Dunne

The Waihi Gold Mine is situated in a high rainfall area (annual average of over 2 m) on the North Island of New Zealand. Water treatment and discharge at the mine has been ongoing for the last 25 years. The first water treatment plant consisted of a æstandardÆ water treatment facility (ferric chloride precipitation) and cyanide detoxification. With time the project has expanded and the volumes of water increased requiring additional treatment methods (reverse osmosis) to meet the water quality for discharge. This paper will provide information on the historical development of the water treatment flow sheets, performance data and operating costs.CITATION:Bertoldi, D, Dunne, R, Twidle, B and Meikle, J, 2013. Water treatment at the Waihi Gold Mine, in Proceedings World Gold 2013 , pp 503-508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Flotation of Phosphate Gangue from Magnetite Fines - Non-Ionic Surfactant as Atrac Collector Modifier

Sep 13, 2010

By A F. D C Varajpo, R C. Weba, C Volkmer-Ribeiro, C A. C Varajpo, N S. Gomes

This study relates to the spongillite deposits from the region of Jopo Pinheiro, in the north-west of the State of Minas Gerais, south-eastern Brazil. The deposits occur in shallow ponds (with a maximum depth of 3.5 m) on a karstic planation surface developed on rocks of the Spo Francisco Neoproterozoic Supergroup. Cenozoic detritic covers are associated with this surface. The field study of spongillite deposits from the Preguita and Avipo deposits revealed sedimentological and pedological similarities between the different deposits. They have a lenticular shape and contain different layers of sedimentary spicules intercalated with layers of quartz sand and clay minerals. Representative samples from the different layers investigated by X-ray diffraction, differential and gravimetric thermal analysis and infrared spectroscopy showed a range from three to 80 per cent of amorphous silica (opal) corresponding mostly to the sponge spicules in the sediments. Optical microscopic investigation determined that the spicules predominantly belong to the sponge Metania spinata. This species is represented by smooth megascleres (alpha type), prickly megascleres (beta type) measuring 240 to 450 mm in length, as well as the spiny microscleres; whereby the smooth megascleres are larger and thinner. The morphological variation of the spicules as well as the presence of more fragmented spicules towards the base of the deposits, portray a variation in texture and in the state of their preservation along the profile, suggesting environmental variations at the time of their formation and deposition.

Jan 1, 2008

By S Watson, L Martinez

Mine projects are complex opportunities that demand a constant assessment of uncertainty, ie risk and upside potential. This is because the value of a mine project is typically influenced by many underlying economic and physical uncertainties, such as metal/mineral prices, metal/mineral grades, costs, schedules, quantities, and environmental issues, amongst others, which are not known with much certainty at the beginning of the project. But, is uncertainty an enemy or an ally of the mine planner/analyst? To answer this question, this paper first assesses and elaborates upon the general concept of uncertainty. It then looks at the different sources of uncertainty in a mining project, such as the orebody, costs and product price uncertainties, and their effect on the final project value. Next, a general?review?of current mine evaluation techniques highlighting their limitations when dealing with uncertainty is made. Finally, an extended evaluation and risk management framework that addresses the existing uncertainty in the (greenfield/brownfield) mine evaluation process is proposed. One important characteristic of this framework is that it uses and manages uncertainty in order to generate additional value to the project; this is done through operational and managerial flexibility, which allow mine planners to minimise/maximise project risk/upside-potential giving a more realistic estimate of the projectÆs market value - this is shown in practical and simple examples occurring at different stages of a mine project, such as exploration and operation. Final conclusions are provided at the end.CITATION:Martinez, L and Watson, S, 2012. Uncertainty - An important source of (additional) value for mine projects, in Proceedings Project Evaluation 2012 , pp 131-140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By D Baas, D Bennett

This paper describes how Brisbane-based PanAust Limited develops process control strategies that are implemented at all operations and are used in functional descriptions for plant upgrades and new projects.The process control strategies are determined by operating management philosophies designed to maximise returns from the company’s assets.The approach is endorsed in the project planning and design phases to ensure facilities and equipment that form the major production assets are fit for purpose and capable of enabling the production managers and operators of the projects to maximise shareholder returns.PanAust’s process control approach has been to develop sets of process control standards which focus on two key areas. The first area covers hardware requirements and architecture, software objectives, control models and individual loop tuning methods. The second area defines control room layout, graphic standards and the alarm philosophy. The application of these standards in a new plant or upgrade decreases the time required to achieve design capacity and optimal performance.The PanAust process control strategy changes the operator’s role from one that controls a number of individual loops to one that sets the control objectives of the processing plant. To achieve optimal performance, all the process areas of the plant are analysed to identify opportunities to improve throughput, recovery and stability. Once a key opportunity is identified, a process control strategy is developed which defines the objective of the control, its functionality and how an operator will interact with it. After development of the control model the operators assist engineers to test and debug it. Once the model is robust, it can then be duplicated throughout the group and developed as a group process control standard.CITATION:Baas, D, Bennett, D and Walker, P, 2014. Developing process control standards for optimal plant performance at PanAust Limited, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 325–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R A. Lynch

The state-of-the-art in cave seismic monitoring is reviewed, with the latest developments in active seismic monitoring included. Seismic monitoring systems are routinely used by most of the world’s block and panel caving mines to track the cave initiation and progression. The current best practice is to use the cloud of seismic event locations as a proxy for cave growth somewhere below. Problems with event location reliability due to seismic ray bending around the (unknown) cave are side-stepped by using sensors installed above the cave. However, the aseismic gap – the (unknown) distance between actual cave back and seismic event cloud – currently hinders reliable estimation of cave geometry.Velocity inversions using the passive seismic data are inexpensive and should be undertaken more routinely. The straight-ray methods should be used with caution, as the underlying assumptions are invalid in caving environments. The double-difference method is more correct for the caving situation, and there have been some promising results published. Constrained geometric inversions make a lot of sense, but have yet to be demonstrated successfully.Two active seismic source have recently been developed for use in the caving environment: a piezoelectric source for ranges up to a few hundred metres and a pneumatically-powered source for ranges up to a kilometre. These sources produce signals on standard mine seismic sensors that can be used to measure seismic velocity variations down to 0.01 per cent resolution. This allows the cave progression to be monitored by measuring tiny changes to seismic velocities as the rock above the cave is fractured and destressed.CITATION:Lynch, R A, 2016. Active and passive seismic monitoring of cave front evolution, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

This paper discusses support requirements for the proposed monorail system to be used in decline development. The monorail drilling and loading systems are systems that move on the rail (monorail) installed in the roof of the decline and supported by roof bolts, suspension chains and steel supports. However, due to the weight of the components of the two systems, it is imperative that the force in each roof bolt, suspension chain and steel support capable of suspending the weight of the heaviest component is determined. Numerical models that relate the weight of the monorail drilling and loading components to the required strength in the support system have been developed. Using these developed models, numerical values of the forces in each roof bolt, suspension chain and steel support, required to suspend the weight of the heaviest component of the monorail drilling and loading systems are determined.

Dec 6, 2010

By R O’Sullivan, D Taylor, J G. McLellan, B Miller

The Mount Isa copper deposit is located adjacent to the city of Mount Isa, Queensland, and lies within a series of Palaeoproterozoic to Mesoproterozoic Superbasins. The deposit is hosted almost entirely within the Urquhart Shale (US), a unit of the Mount Isa Group sediments and part of the Isa Superbasin. The copper mineralisation is separated into two distinct orebodies: the X41 mine (1100 and 1900 orebodies) and the Enterprise mine (3000 and 3500 orebodies). The orebodies are situated in the hanging wall of the major controlling structures, the Paroo Fault, which has juxtaposed older basement Eastern Creek Volcanics against the younger Mount Isa Group sediments cf 1655 ± 4 Ma. Conjecture remains over the exact timing of this thrust event. However, it is clear that inflections on the Paroo Fault have a close association with the orebodies and are an important structural feature in the mineralisation of the Mount Isa copper deposit.The life-of-mine is reducing steadily and new geomechanical modelling techniques were employed to target structurally controlled mineralised zones in three dimensions. Following a structural review of the mine using underground mapping, structural data and core shed observations, a conceptual 3D mine model was constructed utilising existing data modelled in MineSight®. This conceptual model included all the main lithological units and structures. The conceptual model aimed to test the effects of deformation on the main lithological and structural components of the system and attempted to highlight areas of anomalous stress and strain that may indicate a higher likelihood of fluid focusing and mineralisation potential. This project was focused on testing the latter stages of a D3 event (NE–SW compression) and D4 event (SE–NW compression), which are considered to be responsible for the current location of the mineralisation.The fully coupled 3D finite element analysis models resulted in highlighting anomalous patterns of stress and strain and subsequent fluid flow as a result of the two deformation events. The NE–SW D3 simulation provided the best correlation with the known distribution of mineralisation. This event also indicated several areas on the Paroo Fault and within the US that have potential to host further areas of mineralisation. The SE–NW D4 simulation provided less of a correlation with known mineralised zones. However, this event may have been responsible for post mineralisation re-mobilisation of copper on a relatively small scale. Areas of maximum shear strain, shear stress, volumetric strain and fluid flow correlated well with areas of minimum principal stress and provided the best overall match with known mineralised zones. Furthermore, several additional highlighted areas provide a high potential for further discovery of copper mineralisation. Recent exploration drilling north of the Enterprise mine 3000 orebody, utilising geomechanical modelling as part of the targeting criteria, intersected copper mineralisation, providing further validation of the modelling results.CITATION:McLellan, J G, O’Sullivan, R, Miller, B and Taylor, D, 2014. Geomechanical modelling of the Mount Isa copper deposit – predicting mineralisation, in Proceedings Ninth International Mining Geology Conference 2014 , pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By T X. Le, H T. Tran, K Zaw, T Manaka

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Truong Son fold-thrust belt (TSFTB) is a prominent tectonic component of mainland Indochina that occurs as a north-west–south-east-trending tectonic entity that extends from north-eastern Laos, straddles the Laos-Vietnam border area and is submerged under the sea basin in east central Vietnam. The TSFTB hosts numerous regional-scale gold and polymetallic base metal deposits, and the mineralisation occurs along the strike of the belt; however, the potential of many of these deposits are inadequately evaluated. The ore mineralisation is hosted by different rock assemblages, including highly metamorphosed Late Proterozoic metasedimentary rocks and Palaeozoic sedimentary and/or volcanic packages, which were intruded by several phases of magma and underwent a number of tectonic events. Several ore-forming styles – including porphyry, Carlin-type and sediment-hosted orogenic Au – were formed during at least two phases of regional thermotectonism that have been identified in the TSFTB. However, all of the major gold deposits/mineralisations are closely related to region-wide structural breaks and many of them are controlled by large-scale, high-strain zones. The fold-thrust structures in the TSFTB therefore play important roles for regional gold mineralisation and metallogeny.CITATION:Tran, H T, Zaw, K, Le, T X and Manaka, T, 2015. Structural controls on gold mineralisation in the south-eastern Truong Son fold-thrust belt and its significance in regional metallogeny, in Proceedings PACRIM 2015 Congress, pp 521–530 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By D P. Blair

There are two major aspects to wall control blasting – the potential for any blasthole to cause wall damage and the potential for a delayed sequence of blastholes to cause damage. The damage potential of individual blastholes is governed by standoff distance and charge weight. However, for locations sufficiently close to a highwall, dynamic finite element models and field measurements show that there is also a critical nature to those blastholes very close to the wall, over and above standoff distance. At many mine sites, the charge weight/standoff-distance is set by trial and error. Thus, a significant aspect of the present work is the determination of dynamic stress radiating from a blasthole. Unfortunately, the modelling and measurement of this dynamic stress is still faced with many difficulties. Typical models have questionable aspects, which casts serious doubt over their predictions, and it is shown that the Hustrulid Bar experimental technique does not correctly account for stress wave attenuation in extended media. In an attempt to solve the dynamic stress problem, the present work describes a model based on an exact solution under the assumption of viscoelastic material. The model takes full account of the rock mass elastic/viscoelastic properties, the explosive type, geometry and primer location and predicts a dynamic stress for direct comparison with the unconfined compressive strength of the local rock mass. This model predicts the standoff distance required to avoid damage due to a single blasthole. The behaviour of a delayed sequence of blastholes is analysed using an upgraded waveform superposition model, covering a range of initiation delay combinations, which predicts the peak particle motion (PPM) induced in the wall for each combination. This approach shows that there is no need to fire dedicated trim shots close to walls; all that is required is a carefully modified production shot. The mechanism of vibration screening is discussed, and its use in a superposition model highlights the potential of reverse firing (shield blasting) to reduce wall PPM. A conceptual model is also introduced to give a further insight to vibration screening and damage (via ground heave). This model predicts that a centre-lift blast will have a central heave profile and that a reverse-fired shot will produce a smaller power trough than that produced by a standard shot. It is demonstrated that the mechanism of presplit formation is not well understood; nevertheless, experimental evidence shows that presplits can be an effective method for reducing wall vibrations.CITATION:Blair, D P, 2015. Wall control blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 13–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Construction work on one of the world's largest landslide stabilisation projects is drawing to a close in Central Otago. Begun in mid 1990, major stabilisation work has been carried out on seven large rockslides which will be partially inundated when the Clyde dam reservoir (Lake Dunstan) is filled. The work has required the construction of 14.5 kilometres of tunnel, 60 kilometres of surface drilling, 78 kilometres of drilled drainage holes and five million cubic metres of earthworks. The stabilisation programme has been carried out by the Electricity Corporation of New Zealand as part of the Clyde Power Project, a hydroelectric development on the Clutha River.

Jan 1, 1992

By N Guresin, A Cooper, L Lorenzen, H Muller, S C. Dominy

Sampling and metallurgical test work during various phases of engineering?studies?is of?paramount importance for a robust processing plant design. When developing a process flow sheet, risks in achieving desirable financial outcomes are minimised by ensuring appropriate sampling and adequate metallurgical test work supports the engineering and cost estimation at each phase of project development.The quality and type of samples used for metallurgical test work are just as important as the metallurgical test work itself. The key characteristic required of any sample is that it represents some defined portion of a mineral deposit. Representivity should take into account the spatial orientation, lithology, alteration, degree of oxidation, mineralogy and competency of the ore such as hardness and abrasiveness. Statistically representative sampling procedures and an appropriate metallurgical test work program should be designed to bring metallurgical understanding up to feasibility study standard and to give a basis for process plant design.Snowden has observed that the quality of sampling and quantity of metallurgical test work carried out during the various phases of engineering studies are often insufficient to truly support a robust plant design. Some designs are often the result of the plant design based on benchmarks of apparently similar orebodies or buoyant metal prices supporting cash flows until rectifications can be implemented.The paper will discuss important aspects of sampling and test work required for engineering studies in designing process plants based on industrial case studies.CITATION:Guresin, N, Lorenzen, L, Dominy, S C, Muller, H and Cooper, A, 2012. Importance of effective sampling and test work protocols for process plant design, in Proceedings Sampling 2012 , pp 95-108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By B Murphy, A Uliana, P STrgio de Oliveira, G Ara·jo de Souza Franco, T Miettinen

Outotec has performed numerous research and development projects and various surveys in the study of reverse iron ore flotation. Over the past four years their TankCell-70 and TankCell-160 flotation cells at the Germano concentrator of Samarco in Brazil were extensively surveyed. These surveys have revealed some extreme operating conditions in reverse iron ore flotation and are the subject of this paper. Some of the findings include large variations in the content of solids in the various flotation stages. At the bottom of the cleaner cells, the content of solids by weight reached over 60 per cent, whereas at the bottom of the scavenger cell this was less than 50 per cent. Froth carry rates were also significantly different in the various flotation stages. In the case of coarse material, the scavenger cells operated at a froth carry rate of over 40 t/h.m2. With fine material, however, froth carry rates of less than 10 t/h.m2 were measured. High froth carry rates caused significant changes in the residence times at Samarco. In the rougher cells, the fifth cell had more than double the residence time of the first cell. This was even more pronounced with the scavenger cells, where the second cell had more than triple the residence time of the first cell. High froth carry rates also caused losses in iron recovery. As a consequence of such findings, it appears that different rules apply in the sizing of reverse flotation circuits compared to direct flotation circuits. Different operating parameters (mixing intensities and air flow rates) must also be used in the rougher, cleaner and scavenger cells in order to optimise the metallurgical performance. Outotec has also been working on a number of new technologies aimed at improving the metallurgical performance of iron ore reverse flotation circuits by increasing froth carry rate and decreasing fine iron entrainment.CITATION:Miettinen, T, Uliana, A, Ara·jo de Souza Franco, G, STrgio de Oliveira, P and Murphy, B, 2013. TankCell flotation at SamarcoÆs Germano concentrators, in Proceedings Iron Ore 2013 , pp 441-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D Skinner, P Haeussler, D Bradley, A Christie

Mesothermal gold deposits of southernAlaska and Westland, New Zealand have both formed at the seaward edge of major collisional zones in the Pacific basin. In Alaska, production of large fluid volumes correlates in time with the addition of heat into the lower parts of the accreted terranes in the late stages of collisional orogeny. This heat was critical for driving both the metamorphic reactions that released the large volumes of fluid that carried the gold, and the contemporaneous widespread anatexis and magmatism. In Alaska's Chugach terrane, this heat as produced by subduction of a spreading ridge beneath the North America continental margin in the Eocene. The resulting products were the S-type granites and gold-bearing veins. The similar widespread S-type plutonism and gold veining in Westland's Buller terrane suggest that a similar tectonic event could have triggered ore formation along the southeastern edge of Gondwanaland. Based on the Alaskan model, a Devonian or Early Carboniferous age is favoured for high volume metamorphogenic fluid generation and gold vein formation in Westland.

Jan 1, 1995

By P Lindsay

A numerical model has been developed to simulate the effectiveness and costs of a number of conceptual remedial measures aimed at reducing acidity and metal concentrations in the Ngakawau River and its tributaries near the Stockton Coal Mine, situated on the West Coast of New Zealand. The Stockton Coal Mine has been in operation over the past 100 years. During that time, seepage from waste rock dumps has contributed to elevated acidity and metal concentrations in the Ngakawau River and some of its tributaries. The yearly mean rainfall at the mine site is 6000 mm. The model, developed using GoldSim software, simulates rainfall, run-off and stream discharge for 26 tributaries. It then calculates acidity and metal concentrations in the mine impacted tributaries and the dilution downstream from the mine. The model has been calibrated to measured flow and acidity and metal concentrations in the Ngakawau River and some of its tributaries. Acidity and metal loads are removed from the system in accordance with specified efficiencies and capacities of the respective conceptual remedial measures. The user can compare specific remedial measures, or a combination of conceptual remedial measures. The model predicts the acidity and metal concentrations at a number of monitoring stations for any remedial strategy selected by the user. It also calculates the capital and operational costs for that particular remedial strategy. This paper presents the development of the numerical model and describes how the end-user can use it to compare the efficiency and costs of various remedial strategies by running different æwhat ifÆ scenarios.

Jan 1, 2006

Legislation introduced for Queensland and New South Wales Coal mines provides different levels of prescription regarding specification of mine seals û generally in relation to capacity to withstand overpressure. In Queensland, the Coal Mining Safety and Health Regulation (2001), Section 341 (d) places a further onus on the statutory ventilation officer to æensure all ventilation control devices at the mine are properly constructed and maintainedÆ and that the ventilation officer æmust ensure a ventilation control device mentioned in the regulation à and installed at the mine meets the design criteria statedÆ for the ætype of deviceÆ. Based on the experience of the author, it appears that risk management and life cycle approach to seals has not been adopted to the same extent as for other aspects of operations. Further, because of the number of disciplines and personnel involved that may influence various factors affecting seal integrity, the opportunity for oversight or unclear allocation of responsibility is considerable. While suppliers can provide explosion or design rated seals, this should only be a starting point for application of the product in a coal mine. Application is often considered by mine planning staff (taking into consideration mine environment parameters such as water, control of gas, spontaneous combustion risk, etc) in conjunction with the colliery ventilation officer, and then construction completed by contractors under supervision of operational staff. After construction, seals often are managed by operational personnel with input from the ventilation officer. Input of the geotechnical engineer into pillar design, roadway opening size, ground support specification and most stable seal location is also required. The need for a customised design approach for each seal site is proposed in order to take into account the many and variable factors that may influence a site so that improved seal performance reliability and predictability can be developed. A program of quantitative as well as qualitative monitoring of performance and triggers for rectification or maintenance action is required, and would provide support to the aforementioned proposal. Many mines rely on visual/audible inspection and periodic bag sampling as the primary means of assessment. Other significant factors such as seal material properties, rib degradation, convergence, floor heave, effects of water on both structural integrity of the seal as well as the air tightness of the seal do not generally receive the same level of attention. Based on the above observations, the author has compiled a reference checklist in regard to the above matters, including aspects of and approaches to mine and pillar design, geotechnical modelling and data collection, civil engineering design, site evaluation and practical options available.

Jan 1, 2005

By J Allen, B Oats, S Palaniandy, M Lollback

The Julius Kruttschnitt Mineral Research Centre has conducted an intensive VertiMill® (VTM) survey program at the Cannington mine concentrator as part of the ‘collaborative research in stirred milling technology’ program funded by Metso Minerals. Since 2003, Cannington has progressively added grinding capacity into the circuit through VTMs operating in secondary and regrinding duties. Cannington was one of the first mines to adopt this technology in secondary duty by installing two VTM-1500-WBs as part of a capacity expansion to produce sub-100 µm rougher feed. Subsequently, an additional VTM-800-WB was installed in the lead regrind circuit to prepare sub-20 µm cleaner stage feed.Several surveys were carried out to evaluate the VTM performance over a range of changed conditions. Among the key changes in operating variables were circuit power draw, feed rate and water addition to the bottom of the mill. The average specific energy for secondary duty was 3.7?kWh/t. The lead and zinc regrind mills consume 8.1 and 15.3 kWh/t respectively. Generally, the VTM installations have successfully prepared feed for rougher and cleaner circuits by reducing the top size into the floatable regime with steeper particle size distribution, which has led to enhanced recovery. The survey results show the success of VTM installations in secondary (receiving feed from autogenous circuit) and regrind duties.CITATION:Palaniandy, S, Powell, M S, Hilden, M, Allen, J, Kermanshahi, K, Oats, B and Lollback, M, 2014. VertiMill® performance updates in secondary and regrind duties at Cannington mine, BHP Billiton, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By A Garvie, D Kentwell, J Chapman

"Most new mining projects require an initial assessment of the locations and volumes of potential acid forming (PAF) waste that is likely to be moved and dumped in surface waste stockpiles. This requires sampling of the waste rock zones and submitting the samples for a series of tests. Key to the outcome of the waste characterisation process is obtaining sufficient samples that are representative of the various rock types both in number and spatial distribution.Various regulatory bodies throughout Australia and the rest of the world are currently struggling with how to define minimum amounts of sampling to achieve realistic estimates without imposing excessive costs and time constraints on a project.This paper addresses two aspects of the process: what constitutes a æsufficientÆ number of samples how to use those samples in determining volumes of likely PAF material.Geostatistical methods of characterising orebodies with large numbers of samples are routinely used in the mining industry by geologists and geostatisticians to estimate and classify Mineral Resources. In theory exactly the same methods can be used to estimate PAF waste locations and volumes.In practice the number and spatial distribution of dedicated PAF waste samples at feasibility stage is typically so small that it is almost impossible to estimate the spatial distribution of PAF material with any degree of confidence at all. Consequently, the common approach is to characterise a few samples from a lithological unit and then assume that they represent the unit as a whole. This approach, however, can be fraught with risk.This paper describes some of the findings of SRKÆs evaluation of several coal projects with respect to PAF waste evaluation and highlights some common misconceptions held by people working in this area that do not have a knowledge of statistics or geostatistics.CITATION:Kentwell, D, Garvie, A and Chapman, J, 2012. Adequacy of sampling and volume estimation for premining potential acid forming waste evaluation using statistical and geostatistical methods, in Proceedings Life-of-Mine 2012, pp 79-88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By J-P Franzidis, E V. Manlap

Froth transportation characteristics have a significant impact on the flotation recovery especially in large flotation cells. The probability of an attached particle being recovered into the concentrate depends strongly on the location where it enters the froth phase. A mathematical model for froth transportation in industrial flotation cells was proposed (Zheng et al, 2004). The model has been tested on the experimental data obtained from testwork conducted at the Western Metals Hellyer lead/zinc concentrator. The results show that the model fits the experimental data well, especially when the froth is well developed (ie for a deep froth). The model fitting can be significantly improved by incorporating an air dispersion factor. However, the models encounter some limitation, ie inconsistent prediction at different froth heights, due to change in froth viscosity which cannot be modelled at the present time.

Jan 1, 2005