Search Documents

By L. B. Harris

Continuous cyclic unloading during tensile work hardening of polycrystalline zinc at room temperature enables specimens to sustain greatly increased extension. Such enhanced ductility is associated with creep-type extension, during which the cyclic component appears to promote relaxation of internal strains. It is possible to trace the transitions from tension, through enhanced cyclic extension, to fatigue and relate the observed behavior to simpler types of deformation. DISTINCTIVE deformation behavior has been shown to occur when loading includes both cyclic and unidirectional components. For aluminum and copper extended by a sequence of progressively biased strain reversals, coffin1 observed greater fracture ductility and lower flow stresses than during monotonic tension. This may be compared with the reduction in hardness obtained from conventional fatigue softening. But fatigue softening is accompanied by enhanced fatigue life,' whereas Benham3 found that fatigue life was reduced when copper continuously extended during axial load cycling. The corresponding specimen elongation, for large cyclic load amplitudes, was greater than during normal tension. Under different conditions, Bendler and wood4 found that torsional fatigue initiated extension in copper under low tensile loads previously in equilibrium with the specimen; fatigue life was again reduced. Thus there is a type of cyclic softening which is associated with reduced fatigue life and which occurs when the cyclic loading is accompanied by a unidirectional strain component. Further, the fracture ductility or extension obtained from the unidirectional component can exceed that obtained in the absence of cyclic load. Specimen extension was not initiated by axial fatigue at small load amplitudes;3 hence Benham's work distinguishes between fatigue at large and small amplitudes, the former often being linked with unidirectional deformation because of similarities in strain Structure. The initiation of tensile extension during torsional fatigue,4 however, occurred with small amplitudes. Comparable changes in behavior have been ob- served during creep. kennedy' found that combined cyclic and creep stresses on lead at 32°C increased the rate of elongation over that for simple creep, the consequence being a reduction in creep life. It was also demonstrated that small cyclic stresses applied after creep deformation initially increased recovery, but that prolonged application produced only normal fatigue hardening. It is clear that physical properties can be changed by interaction between the cyclic and unidirectional deformations, but owing to the number of different ways in which the deformations can be combined and the large number of possible variables for each combination, trends of behavior become easily obscured. One definite conclusion is that enhanced ductility or increased extension can be obtained by cyclic action, and it is this process that has been investigated for the tensile test by measurements of the extra tensile strain produced by the addition of a cyclic tensile component. EXPERIMENTAL PROCEDURE Material. Specimens were 99.99 pct Zn wire of 1.6 and 2.0 mm diam. Mean grain diameter was 0.02 mm, sufficiently small to give a ductile necked-down fracture under all loading conditions. All experiments were conducted at an average temperature of 20°C. Normal Tension. Unidirectional tensile curves at different strain rates were obtained from an In-stron testing machine, on which load-time curves were recorded autographically, using gage lengths of 5 and 10 cm. Straining was at constant cross-head velocity, and quoted strain rates are with reference to initial specimen length. Measurements of total elongation under simple tension were also made on the tensile machine that had been modified to incorporate an added fluctuating load. Combined Tension and Rapid Cyclic Load. An electromagnetic vibrator was coupled to the elastic beam of a Hounsfield ensometer- and driven sinus-oidally from a power amplifier at frequencies from 20 to 360 cps, the flexible connecting links on the tensometer being replaced by rigid fixtures to eliminate lateral vibration in the specimen. One end of the specimen was pulled by the normal extension drive of the tensometer while the other end, fixed to the elastic beam and vibrator, was subjected to rapid oscillations of load. It was thus possible to apply cyclic load to a tensile test without altering the rate of extension of the specimen

Jan 1, 1964

By Chauncey L. Berrien

The United Verde Copper Company's mine is at Jerome, Ariz. The orebodies arc of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron schist contact, with the orebodies extending about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. Three types of ore are mined; schist porphyry and the so-called "heavy" or "massive sulfide" ore. Approximately 50 per cent. of the total tonnage mined at present is of the latter class. A representative analysis of this ore indicates 42 to 46 per cent. sulfur. Because of the high sulfur content, blasting in this ore is an extremely hazardous operation. not only does it endanger the lives of men who may be in the mine at blasting time but it also becomes a potential fire menace when timber is in close proximity to shots being fired in these massive sulfides. The origin of the fires of 38 years ago, embers of which are glowing to this day, may perhaps be attributed to dust explosions due to blasting in the massive sulfides of those early square-set stopes. Dust Explosions Dust explosions in coal mines are a common source of mine disasters. That such explosions may be of common occurrence in metal mines is not generally known, but it is known that metal-mine dust will explode and such explosions have been investigated by the U. S. Bureau of Mines at the Pittsburgh Experiment Station. Samples of "heavy sulfide" ore from the United Verde mine were used in the tests. After studying the results of the tests it was concluded1 that: 1. Dust explosions were initiated in sulfide ore dust in the gallery with a charge of as low as 75 g. of 60 per cent. gelatin dynamite. 2. The exploding dust generated considerable pressure.

Jan 1, 1930

By T. W. Watson, D. R. Flynn

Measurements have been made of the thermal conductivity and electrical resistivity of two specimens of 0.005-cm (2-mil) Be-Cufoil over the temperature range -140° to +200°C. The thermal cmductivity of Be-Cu Alloy 125 was found to be significantly higher than that of Alloy 25, which had a higher impurity content. The thermal conductivity and electrical resistivity values obtained were in concordance with the Smith and Palmer relation for copper alloys which states that ? = 0.0239 (T/p) + 0.075 where A is thermal conductivity (W cm-' deg-'), p is electrical resistivity (microhm-cm), and T is absolute temperature (OK) , indicating that the Smith and Palmer relation can be used to predict the thermal conductivity of this type of Be-Cu alloy over the temperature range -140" to + 200°C to within an accuracy suitable for most engineering applications. THE National Aeronautics and Space Administration, Goddard Space Flight Center, Greenbelt, Md., requested the National Bureau of Standards to measure the thermal conductivity of 0.005-cm Be-Cu foil which was to be used to fabricate antennae for use in Radio Astronomy Explorer space craft. It was felt that measurements had to be made on the actual antenna material, rather than on a thick bar of similar material, since the cold-working and age-hardening properties of the alloy would make it very difficult, if not impossible, to place a thick bar in the same metallurgical state as the 0.005-cm material. As discussed in Section 111 of this paper, the thermal conductivity of many copper alloys can be computed rather accurately from electrical resistivity data using an empirical relation developed by Smith and palmer' and further confirmed by owell.' However, there has been very little work done on correlating thermal and electrical conductivities on Be-Cu alloys. We were reluctant to assume the validity of the Smith-Palmer relation on Be-Cu alloys because of the very large mass difference between beryllium and copper. As will be seen, however, our experimental results indicate that the Smith-Palmer relation is valid for the two alloys on which we made measurements. I) DESCRIPTION OF SAMPLES Samples of Be-Cu Alloy 25 and Be-Cu Alloy 125 were furnished to NBS in the form of rolled strip material, 0.005 cm thick by 5.08 cm wide. The Be-Cu Alloy 25 was purchased by NBS in the form of a continuous length of flat strip. The Be-Cu Alloy 125 was furnished to NBS by Goddard Space Flight Center in the form of two lengths of strip that had been formed into "tubing" of about 1.2 cm diam, with one side of the strip overlapping (but not connected to) the other side by about 90 deg. This "tubing" had been opened up to be flat and then rolled onto spools of about 3 cm diam. When unrolled, the strip would spring back into tubular form. Samples of both of the Be-Cu alloys were chemically analyzed by the NBS Analytical Chemistry Division. The beryllium content was determined quantitatively by the phosphate-gravimetric method to be 1.83 wt pct for Alloy 25 and 1.80 wt pct for Alloy 125. The two alloys were also examined by a general qualitative spectrochemical method for metallic elements. The Alloy 25 specimen contained between 0.1 and 1.0 wt pct Al, Co, Fe, and Si and between 0.01 and 0.1 pct Ni. The Alloy 125 specimen contained between 0.1 and 1.0 pct Co and between 0.01 and 0.1 pct Al, Fe, and Si. Other metallic elements present were in amounts less than 0.01 pct. The NBS Engineering Metallurgy Section measured the tensile strength, elongation, and Knoop hardness of both the Be-Cu Alloy 25 and the Be-Cu Alloy 125. These are given in Table I. The NBS Engineering Metallurgy Section also prepared photomicrographs of the two alloys; these are shown in Figs. 1 and 2.

Jan 1, 1969

By L. L. Melton, W. T. Malone

Fluid mechanics research conducted with non-Newtonian fluid systems now permits prediction of the behavior of these fluid systems in both laminar and turbulent modes of flow through circular pipes. Present work concerns non-Newtonian fluid systems currently used in the hydraulic fracturing process. During fracturing treatments, an unsteady-state condition may frequently be encountered arising from. the reaction rate of a chemical additive. This condition must be evaluated in order to predict the actual behavior of a particular fluid during field application. Design and operation of the apparatus used to determine fluid-flow behavior permit obtaining data under such non-equilibrium conditions. This paper shows methods used to obtain rheology measurements, develop hydraulic relationships and evaluate chemical reactions producing unsteady-state conditions. Engineering application of this research is illustrated by employing measured rheological values and developed hydraulic retationships to produce frictional pressure loss (psi/100 ft) us flow rate (bbl/min) charts of common tubing and casing sizes for an example fracturing fluid. How these charts and chemical reaction rate information are then combined to predict actual turbulent hydraulic behavior during unsteady-state field conditions is also discussed INTRODUCTION Many fluids used in hydraulic fracturing contain chemical additives which impart non-Newtonian fluid properties that may drastically alter their hydraulic behavior. Equally drastic alteration in wellhead pressure, injection rate and hydraulic horsepower requirement may result from these fluid properties. Prior research conducted to relate non-Newtonian fluid properties with hydraulic behavior has not as yet produced a universal relationship, particularly for the turbulent flow region. which of the many Possible non-Newtonian fluid properties is responsible has not been conclusively established. A systematic description, suggested by Metzner, of the many possible non-Newtonian fluid properties exhibited by real-fluid behavior, and a current discussion of theoretical and applied aspects of non-Newtonian fluid technoloy can be found in Handbook of Fluid Dynamics. f Little or no research has previously been attempted with fluids exhibiting time - dependent properties. Addition of chemicals during a fracturing treatment is often accomplished by continuously mixing and displacing the fluid. This produces a time-dependent effect or unsteady-state condition while the fluid is progressing through surface and wellbore conductors. This condition is due to solution or chemical reaction of the additive. Considerable departure from conventional methods of obtaining and interpreting data was found necessary to consider these conditions. Therefore methods were developed to obtain hydraulic behavior information under these complex, unsteady-state conditions. Relationships presented in this paper to predict hydraulic behavior of non-Newtonian fluids in circular pipes were obtained by constructing and operating a small pipeline apparatus in the manner of a pilot-plant study. These relationships are suggested as scaleup equations and are not proposed as fundamental rheological parameters. While perhaps deficient from a fundamental research viewpoint, a pilot-plant study does permit the determination and convenient evaluation of variables pertinent to a process. A pilot-plant study can result in a valid engineering application procedure even when fundamental relationships are still undefined. An excellent series of articles by Bowen has appeared in the chemical engineering literature.2-8 These give a thorough review of proposed hydraulic relationships and their limitations for non-Newtonian fluid behavior in circular pipes. A graphical method is presented to scale up data for a fluid exhibiting an anomalous hydrau1ic behavior in the turbulent flow region. Considerable assistance has been obtained from these articles to interpret the anomalous behavior noted during this investigation. These articles also provided assurance that a pilot plant is a practical approach to evaluate the hydraulic behavior of non-Newtonian fracturing fluids. _____________

Jan 1, 1965

Fifty to 75 million years ago, hydrocarbon-bearing rocks were formed in the Green River formation of Colorado, Wyoming and Utah. The hydro- carbons can be extracted from these rocks, marl- stone but misnamed oil shale, after crushing and intense heating. At about 900°F the marlstone decomposes to produce liquid shale oil. A press release from the Colony Development Co. describes a process which may permit, for the first time, economically feasible access to shale oil. Shale oil has resisted economic extraction for almost three centuries. According to the USBM, a patent was issued as early as 1684 in England to produce "oyle from a kind of stone". France produced oil from marlstone in 1838 and a dozen years later, Scotland started an oil shale industry, producing kerosine, that lasted nearly 100 years. In both countries, the process involved crushing the stone and retorting it to decompose the kerogen-a long and costly process at that time. In 1859, Edwin L. Drake brought in the first oil well in Titusville, Pa., and shale oil faded into oblivion.

Jan 8, 1965

By William Waters Van Ness

The Pierrefitte mines, situated in the South of France, in the district of the Hautes-Pyrenees, owe their name to the fact that the first mining operations of any extent, and of comparatively reccnt date, were carried out in the neighborhood of the village of Pierrefitte, which is a branch terminus of the Midi railway. The Pierrefitte mines, however, embrace a wide extent of country and several different concessions, on most of which comparatively little exploration-work has been done. The portion of the property presently to be described is a zone running roughly E—W., over a distance of about 5 miles from the valley of Cauterets to the valley of Estaing, the ridge dividing these valleys being a spur of the main chain of the Pyrenees, and running more or less at right angles to it. According to local tradition, which various indications tend to confirm, these mines are of ancient date, the first workings being attributed to the Romans, who are supposcd to have sought not only the lead but also the silver which is contained in the ore. Old slags have been found in the neighborhood which might well have been produced from the cupellation of lead-ores. These old workings, while of considerable extent at times, do not seem to have extended beyond a depth of 100 ft., even this depth being somewhat exceptional. The old notarial records of the district show that mines were known to exist, and that they were even worked, in the sixteenth century, but since the mines were abandoned (by the Romans or others) considerably prior to this period, very little

Jan 1, 1909

By J. L. Taylor, P. Duwez

The phase boundaries in the ternary system Ti-Cr-Al have been established at 1800° and 1400°F for alloys containing more than 60 pct Ti. The martensite transformation temperature has been measured for the titanium-rich alloys. THE studies of binary alloys of titanium with the transition elements which have been published so far1-0 ndicate clearly that the solubility of these elements is always much greater in the high temperature body-centered cubic form of titanium (ß phase) than in the low temperature hexagonal form. In this category of alloying elements are iron, nickel, chromium, manganese, vanadium, molybdenum, tungsten, columbium, and tantalum. Although studies of the nontransition elements have been rather limited, early work on titanium binary alloys'" has shown that most of them were not very soluble in the a form, with the exception of aluminum, for which the solubility in a is about 25 pct.13, 12 In addition to this large solubility in a, aluminum is also soluble in ß titanium to the extent of about 35 pct and the transformation temperature from ß to a is raised with aluminum content. This effect is also typical of aluminum, in contrast with that found for the transition elements which lower the ß to a transformation temperature. Therefore, it may be anticipated that tprnarv titanium alloys with aluminum and any one of the transition elements will constitute a class of ternary alloys having characteristic features absent in alloys involving two transition elements. Chromium was chosen as a typical transition element for the present study because ternary alloys of Ti-Al-Cr commercially produced have been found to possess very interesting physical properties (MST-3 pct A1-5 pct Cr of Mallory-Sharon).'" Binary Systems The binary systems Ti-A1 and Ti-Cr have been established recently by several investigators. The data used in this investigation were taken from the complete diagram of Bumps, Kessler, and Hansen." This diagram agrees quite well with earlier investigations." For the Ti-Cr system, the phase boundaries at 1800" and 1400°F were taken from refs. 6 and 7. The binary system Cr-A1 has been studied recently by Bradley." This system is rather complex and contains not less than seven intermediate phases. The present study was limited to the titanium corner of the ternary system (less than a total of 40 pct Cr plus Al) and none of the phases present in the Cr-A1 binary alloys were found in the ternary alloys investigated. Experimental Technique Microscopic observation and X-ray diffraction measurements were used to identify phases and de-

Jan 1, 1954

By H. M. Howe

(New York: Meeting, October, 1913.) 1. INTRODUCTION.-This paper gives the results of our micro-graphic determinations of the position of Ae3 in a series of 14 hypo-eutectoid steels of varying carbon content, one of them very rich in phosphorus, and of SEe for one hyper-eutectoid steel. We have pro-ceeded chiefly by noting the temperature -at which the reabsorption of the pro-eutectoid element is found to be complete after a 30-min. holding, but in part also by noting the temperature at which its precipitation begins. Observations on these same steels by Messrs. Burgess, Crowe, and Rawdon, of the United States Bureau of Standards, are given in a paper' issued simultaneously with this, while in a third paper s one of us compares these data with those of earlier observers. These three papers are treated as one whole by numbering their sections, tables, and illustrations continuously, and by setting the folding plates of micrographs at the end of the last paper. THE COMPOSITION OF THE STEELS EXPERIMENTED ON is given in Table I. Notation. and Definitions.-Following Osmond's development of Tschernoff's notation; in which " Ac3 " is the upper limit of the hypo-eutectoid part of the transformation range as observed in heating up, and " Ar3 " is that same limit as observed in cooling down, and following the usual custom of calling the upper limit of the hyper-eutectoid part of that range "SE," we may go farther and call this latter limit " SEc " when observed in heating up .and " SEr " when observed in cooling down.

Jan 6, 1913

Jan 1, 1955

By Maurice Grieves

The great majority of shafts constructed today are still excavated by drilling and blasting, a method which changed very little in over 100 years until the introduction of the mechanical lashing unit and cactus grab by the South Africans, which enabled muck to be removed as fast as massive hoisting systems could handle it and resulted in very rapid rates of sinking. Record breaking month's performances were achieved at -Hartebeestfontein No. 4 shaft, October 1960-337.1 m; Western Reefs No. 4 shaft, October 1961-340.7 m; and Buffelsfontein eastern twin shaft, March 1962-381.2m. The method was very labor-intensive, requiring a crew of over 60 workers at the shaft bottom during the drill cycle. Safety precautions were strict, but in the drive to achieve rapid advance, cases of personal injury were still somewhat high because of the large number of people engaged in this potentially hostile environment. The South African method, as it came to be referred to throughout the rest of the world, was adopted in the United Kingdom in the late 1950s in a modified form with greatly reduced manpower and nonsimultaneous sinking and lining, which was insisted on by the British Mines Inspectorate. In that instance, it was successfully used to sink the 7.3-m-diam concrete-lined shafts at Kellingley to 770 m depth, with rates of advance of over 90 m/month achieved, a British record at that time. During the sinking of the 1.15-km-deep twin shafts at Boulby potash mine in the UK in 1970, the method was again used, but for the first time ever in Britain exemptions from the mining code permitted the use of crash beams, crash doors, jack catches, and semi-simultaneous sinking and lining techniques. New British shaft sinking records of over 120 m/month were achieved in both shafts. Similar equipment and techniques were used in the early 1970s to sink several deep shafts in Canada, notably Creighton #7 and the Con zinc mine at Yellowknife in the NW Territories. Today, this equipment is standard for deep shafts in the US and the rest of the world. However, with the tremendous escalation in mining labor costs, the impact of health and safety legislation, and environmental regulations, coupled with a very real shortage of miners willing to work in this exposed situation it was apparent that an alternative to the labor-intensive conventional method of shaft construction had to be found. Recognizing the trend is inevitable, one or two major German shaft sinking contracting firms began to take a fresh look at full face boring techniques applied to tunnels and raise bored shafts. The results were most encouraging. Tunnel drivage techniques using moles had developed considerably from Colonel Beaumont's original channel tunnel machine circa 1880 to the superbly engineered Priestley machine selected to cut the British side in 1975 and the double shielded Robbins Grandori borer on the French side of the English Channel. Full face tunnel machines were being successfully used to drive uphill in inclined shafts in Austria and Switzerland. At Mapprag in Switzerland, the Demag mole drove the first (intentional) vertical transition and curve, and then went on to successfully complete the 730-m-long penstock shaft at an inclination of 35°. In Austria, the Wirth mole drove the Kaprun Glacier ski-lift railcar tunnel at record breaking rates of 457 m/MONTH (best 30 m/d) through green schist at an inclination of 29° for a distance of 3.35 km while the Hydro tunnel at Sarrelli in Switzerland was being driven by the Robbin's mole at an inclination of 35°. Simultaneously, extremely promising results were obtained using large assemblies of cutter discs on raise borer heads, such as the 4.87-m-diam X 460-m-deep shaft raised by Teton for Jim Walter Resources Inc. Bearing in mind that most mine shafts in the future (unless in exceptionally competent rock) will require some form of lining, and the trend will be toward deeper shafts as the more easily accessible mineral deposits become exhausted, it was seen that normal raise boring had definite limitations in vertical accuracy, in the limitation imposed by the drill string on the available torque that could be applied to the cutter head, and in the risk of collapse of the unsupported shaft rock wall in friable or jointed and fissured ground, since it is not possible to apply any form of temporary support until the permanent lining is being installed. A further problem was the economics of installing a subsequent lining, necessitating setting up a headgear and hoisting arrangement approaching in size that required for conventional drill and blast sinking and lining. Because of the economics, German contractors opted for a phased transition from drill and blast to the full face, rodless, out of the solid shaft mole, by starting off with a down-the-hole shaft boring machine -without a drillstring-but using a pilot hole to get rid of the muck.

Jan 1, 1982

By R. R. Unterberger

Three different physical techniques have been used to see through or probe into rocks, so miners might know what is ahead or overhead. These are radar, sonar, and a unique type of sonar called nonlinear sonar. Five radar systems have been developed. The highest frequency used is 4300 MHz for detecting small fractures at close range. This gives the best resolution. For longest range (over 2000 m, or 6560 ft) we use the 30 MHz radar for finding faults ahead of mining or ranging to salt dome flanks. Two types of salt, dome and bedded, are recognized. Radar works well in dry (dome) salt, but not in bedded salt which contains small amounts of water. The dipole moment of water absorbs energy from the radar. Thus was born the 30 MHz radar system and sonar probing systems. These can probe to 100 m (328 ft) even into wet salt. All probing systems measure data in time, which are converted to distance by measuring the time of travel of radar or sonar through salt pillars of known thickness. Ranges of probing in salt are from less than 1 m (3.3 ft) to more than 2000 m (6560 ft). Uses of radar and sonar probing in mines include mapping the top of salt above a mine; mapping salt dome flanks; finding impurities in salt such as anhydrite, sandstone, or potash stringers; locating old boreholes in salt pillars; locating fractures in salt; and finding faults or water zones ahead of mining.

Jan 1, 1985

By K. C. Ten Brink, Allen D. Garrison

A rrevious paper1 reviewed some of the properties of clays and shales and presented some data on the nature of the gelling phenomenon. It included a brief discussion of origin of clays and shales, their composition, structure, retention of water, ionization, base exchange, and the nature of the gelling of water suspensions. Other publications of the Institute2-8 have discussed the properties of clays and their relations to drilling-fluid behavior and control. It is the purpose of this article to present some new data obtained and arranged in a different manner and making possible a better understanding of the chemical reactions involved in the control of drilling-fluid characteristics during the normal drilling operations. Experimental Procedure The difficulties involved in the measurements of the flow characteristics of plastic fluids are too familiar to recite. The possible applications of some of the well-known instruments to this problem have been adequately discussed by Hobson9 and he has given an excellent bibliography. Although there are many viscosimeters of varied design, none of them appear to fulfill the most obvious demands of accuracy in the measurement of clay or shale suspensions. Since the fluid characteristics are dependent on the rate of flow of the fluid, and the viscosity usually falls off very rapidly as the rate is increased, it is clear that the first requirement is that the instrument shall be capable of a wide variety of speeds. The viscosity of the fluid at any fixed and constant rate of flow is also a function of time, so that the second demand is that the instrument shall be capable of a constant and continuous motion for a prolonged period of time.

Jan 1, 1940

By K. C. Ten Brink, Allen D. Garrison

A rrevious paper1 reviewed some of the properties of clays and shales and presented some data on the nature of the gelling phenomenon. It included a brief discussion of origin of clays and shales, their composition, structure, retention of water, ionization, base exchange, and the nature of the gelling of water suspensions. Other publications of the Institute2-8 have discussed the properties of clays and their relations to drilling-fluid behavior and control. It is the purpose of this article to present some new data obtained and arranged in a different manner and making possible a better understanding of the chemical reactions involved in the control of drilling-fluid characteristics during the normal drilling operations. Experimental Procedure The difficulties involved in the measurements of the flow characteristics of plastic fluids are too familiar to recite. The possible applications of some of the well-known instruments to this problem have been adequately discussed by Hobson9 and he has given an excellent bibliography. Although there are many viscosimeters of varied design, none of them appear to fulfill the most obvious demands of accuracy in the measurement of clay or shale suspensions. Since the fluid characteristics are dependent on the rate of flow of the fluid, and the viscosity usually falls off very rapidly as the rate is increased, it is clear that the first requirement is that the instrument shall be capable of a wide variety of speeds. The viscosity of the fluid at any fixed and constant rate of flow is also a function of time, so that the second demand is that the instrument shall be capable of a constant and continuous motion for a prolonged period of time.

Jan 1, 1940

By David W. Brunton

From the old-fashioned " grab-sample " to the modern timing-device, which takes a machine-sample with mathematical precision, there is a wide gap, which was only crossed by many years of toil and unremitting endeavor. Even to-day, notwithstanding the advancement in the art, " grab-sampling " is still practiced—sometimes to afford the unscrupulous mine-promoter a basis for fairy-tales with which to entrap the too-gullible investor, and often by milling and smelting companies to determine the amount of moisture in custom-ores. The latter practice is almost as reprehensible as the former, and it causes more trouble and ill-feeling between seller and buyer than all other factors put together. -NO reputable concern to-day would think of attempting to determine by grab-sampling the amount of gold, silver, lead, or copper contained in an ore, and yet many buyers expect the miner to accept the results of grab-sampling in the determination of the amount of water contained in the ore, forgetting that accurate results are just as necessary here as in the determination of the metals, because the result determines the percentage of weight of the ore which shall be excluded and considered to have no value whatever. Samples for the determination of moisture should be taken with as great care as samples for the determination of metallic content, and in order to avoid the extra expense of a separate operation moisture-samples should be taken from the sample-safe. As the sample reaches the sample-bin in a smaller stream and by a more circuitous route than the " reject" travels in its path to the outgoing car, it loses more moisture en route, and a constant should be added to compensate for this difference. Carefullg ,con ducted experiments have shown that the differ.elice in loss of moisture between the two routes does not exceed 10 per cent. in summer and 7 per cent. in winter. For instance,

Jan 1, 1910

By Robert F. Mehl, Edward L. McCandless

Oriented overgrowths and intergrowths among both metallic and nonmetallic substances have been recognized and studied for well over a century. The work of Widmanstätten in 1808 on the geometrical structure in meteorites, a structure known by his name, demonstrated that oriented intergrowths can occur in purely metallic systems. This fact led to much of the early microscopic study of alloys, contributing greatly to the advance of physical metallurgy. The problem has been attacked again in recent years in a comprehensive fashion, with the object of discovering what atomic movements may occur during phase changes in alloy systems. Much of this work has appeared in the A.I.M.E. Transactions in a series of papers published by Mehl and coworkers beginning in 19311. Although many aspects of this general problem remain unsolved, it may be said that the orientation of a new phase forming by precipitation from solid solution or by transformation invariably bears a unique relationship to the orientation of the phase from which it formed, and that similarity in atomic patterns on atomic planes in the two phases play an important part in determining the orientation relationship. Analogous orientation relationships exist in oriented intergrowths in nonmetallic systems—mineral or inorganic. In 1827 Haidinger2 discovered natural intergrowths of hematite and magnetite, and demonstrated that the rough form of the magnetite octahedrons was delineated by small crystals of hematite, of which the basal (00.1) planes lay parallel to the octahedral cleavage planes of the magnetite. The description of this orientation relationship was later completed by von Rath3, who showed that the edge (00.1): (10.1) in hematite lies normal to the [Ill]

Jan 1, 1937

By A. W. Hull

The new valves described in this article are the latest product of the Research Laboratories of the General Electric Co. Some of them are still in the laboratory stage, others have already found important applications. Some of the larger ones, which have graduated from the laboratory, are waiting for their apprenticeship in industry, there to refine their frailties and complete their preparation as electrical servants. The career that awaits them, though dimly foreseen, appears fascinating. And as surely as history repeats itself, scenes still more romantic, now beyond the horizon, will unfold as we approach them. This is the romance of science. Counting Electrons Let the smallest tube lead the march of review. It is a special Pliotron, designed to measure currents smaller than any yet detected. It goes by the unromantic name of Pliotron FP-54. Fig. 1 shows this miniature tube—miniature in performance rather than size, for it is the size of an ordinary radio receiving tube. Its appearance has nothing distinctive, except the quartz beads above and below the plate, which support the grid. They minimize insulation leakage. In principle, the FP-54 is like any grid-controlled high-vacuum electron tube; but in structure and operating characteristics it is entirely special. An extra "space-charge" grid, maintained at 3 volts positive with respect to the filament, holds back the small but pernicious current of positive ions emitted by the filament; the normal plate voltage is 6 volts, grid bias 3 volts, thoriated-tungsten filament temperature 1700" K., plate current 40 microamperes. These conditions are essential to the avoidance of grid-currents, which may consist not only of insulation leakage and positive ions from the hot filament and from residual gases, but of high-speed electrons from the filament, photo emission from the grid due to the light of the filament, and electron emission caused by X-rays generated by the impact of electrons on the plate.

Jan 1, 1932

By George Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro-posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bitu-minous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O'Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

By A. L. Holley

The members of the society are doubtless aware that the production of American Bessemer steel works is constantly increasing; that the same converters and machinery are doing more work every year. This enlarged output is due to various causes, chiefly the following: 1st. Better organization—better knowledge on the part of both managers and men, of the plant and the process; of the way to economize the more exhausting labor, and of the arrangement of the details of labor and operations so that they shall not conflict; also, more pluck—a greater willingness to take risks, or, more properly, such an intimate knowledge of the nature and capacities of the refractory linings in various stages of disrepair, and the probable be- . havior of the fluid metal at various stages of its treatment, that the precise nature of the risk may be better known, so that the works may be crowded to their full capacity. In the early practice, after getting four or five consecutive heats in a day, the men preferred to " let well enough alone," and to devote the remaining time to preparation for another turn. Now, thirty, and sometimes forty heats are regularly made during the twenty-four hours, day after day, without the frequent occurrence and without the fear of breakdowns or " messes," as the spilling of steel charges was graphically named in Sheffield. 2d. Although no new refractory materials have been developed, improved means of preparing such as we have, and of imbedding

By Cornelius F. Kelley

AT the Annual Meeting of the A.1.M.E. last February, Cornelius F. Kelley, chairman of the Anaconda Copper Mining Co., was presented with the Charles F. Rand Memorial Medal for "conspicuous success as administrative head of great enter- prises engaged in the production of nonferrous metals at home and abroad; for inspiring leadership of an organization that has trained able engineers for service wherever ores are mined and metals are recovered; and for enhancing the prestige of metal mining in the financial and industrial world." Mr. Kelley's acceptance speech follows: I am not unmindful of the fact that the distinction is not to be considered a personal one, but that by the language of the citation itself it is rather a recognition of the service that has been performed by the many trained men of an industrial organization that in the arts of mining and metallurgy and in the fabrication of metal products has performed a distinct service to the industry and to mankind. In that spirit, the award is accepted, and on behalf of the organization I represent and myself, I thank you and assure you that the honor is deeply appreciated.

Jan 1, 1944

By H. F. Hebley

In recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and cleaning of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal. Illustrative of this condition is a table of ash contents for the various petrographic constituents of Illinois coal (No. 5 bed) as given by Mitchell' (Table 1).

Jan 1, 1934