Search Documents

By S. Pearson, L. Rotherham

Measurements have been made of the variation of internal friction with temperature for spectroscopically pure silver, and for o series of solid solutions of silver with cadmium, indium, and tin, using a Ke-type torsion pendulum apparatus. Some experiments have also been made to investigate the effect of nonmetallic impurity on grain boundary relaxation in silver. The effect of the alloying elements is to increase the grain boundary viscosity, and to raise the activation energy for grain boundary relaxation from 22,000 cal per mol for pure silver to 43,000 cal per mol for the solid solutions; the same value being obtained, within the limits of experimental error, for all the alloying elements and solute concentrations investigated. Results of the experiments show exactly the same trend as those obtained previously for a similar series of copper solid solutions. They are in agreement with the general theory of grain boundary relaxation developed by Zener and Ke, but do not seem to be in agreement with either of the mechanisms so far put forward to explain grain boundary slip. EXPERIMENTS described in this paper were made as part of an investigation into the effect of alloying elements in substitutional solid solution on grain boundary viscosity, measured by the internal friction method developed by Ke.&apos; The apparatus and experimental procedure have already been described.&apos; Preliminary work was done with spectro-scopically pure silver. Experimental Work Materials Used—All the materials were supplied in the form of % mm diam wire by Messrs. Johnson Matthey and Co. Ltd. The silver and all the alloying elements used were spectroscopically pure. Composition of the alloys is given in Table I. They were all melted and chill cast under the same conditions as the copper alloys. The ingots were rolled to 1/4 in. sq rod with intermediate annealing at 600°C in an atmosphere of cracked ammonia when necessary. These rods were then drawn to wire by standard procedure with intermediate bright anneals at suitable steps in the drawing operations. Specimens from the annealed wires were sectioned longitudinally. mechanically polished, and examined under the microscope. They were then etched and reexamined. Grain sizes were reasonably uniform for all wires, and no traces of a second constituent were observed. The wires were weighed before and after testing so as to measure any loss of the alloying element due to evaporation. The loss was less than the accuracy of measurement—< 0.1 pct of the total weight— for the Ag-In and Ag-Sn alloys, but appreciable loss of weight occurred in the case of the Ag-Cd alloys. The percentage loss is given in Table 11. X-ray diffraction photographs were taken of all thc wires after test to determine whether there was any marked preferred orientation. Results of the examination are given in Table 111. Experiments on Spectroscopically Pure Silver-— Experiments were made on specimens in which the grain diameter was small relative to that of the wire, and on one specimen in which the grains were grown by the usual strain-anneal method to extend across the full diameter of the wire. These large grained specimens will be referred to as single crystal specimens. The wires were annealed for 11/2 hr at 700°C, and experiments were made at two frequencies of vibration, 1.5 and 0.4 vibrations per sec. The variation of internal friction with temperature is shown in Fig. 1. Experiments on a second small grain specimen gave approximately the same results as for the first wire. It will be seen from Fig. 1 that the peak in the curve for the small grained wire, which is presum-

Jan 1, 1957

By C. H. Li, S. H. Bendel, J. A. Sartell

Small additions of Mg to a 62 Cu-38 Ni alloy reduce the oxidation yates drastically between 500° and 850°C. Metallographic examination of the oxide scale disclosed a continuous network, identified by X-ray diffraction as (Ni, Mg)O solid solutions, located along the former alloy grain boundaries. This network acts as a barrier to diffusion. It is thought to result from the segregation of mg to the alloy grain boundaries. Oxidation occurs preferentially in these regions because of the presence of this more active element. To substantiate these ideas, homogenized alloys ulere oxidized. No oxide network was produced and oxidation rates were the same as for the parent 62 Cu-38 Ni alloy. An interesting aspect of the oxidation of the 62 Cu-38 Ni alloy previously described by the present authors, is the relationship between oxidation kinetics and changes in the microstructure of the oxide.&apos; The oxide scale on these alloys consists of two layers: a thin layer of CuO outside a much thicker layer of Cu20 in which particles of NiO are dispersed. In addition, immediately beneath the oxide-metal interface there is an internally oxidized zone in which NiO particles are dispersed in a copper-rich alloy matrix. Experimental observations on the growth of the individual layers under isothermal conditions have led to the conclusion that the rate-determining step in the oxidation of this alloy is the diffusion of anions through the Cu20 layer. It has been found that this diffusion rate is increased by the recrystallization of the outer CuO layer. Willardson and Gorton have reported that the addition of magnesium to the 62 Cu-38 Ni alloy causes a decrease in the oxidation rate.2 The present investigation was undertaken in order to determine the mechanism by which magnesium additions improve the oxidation resistance of the 62 Cu-38 Ni alloy. EXPERIMENTAL PROCEDURE Fifty-gram ingots of Cu-Ni alloys were prepared by vacuum melting materials of 99.999+ pct purity. These ingots were then remelted in a He atmos- phere and magnesium added in the form of a previously prepared and analyzed Cu-Mg master alloy. This procedure was necessitated by the high reactivity of pure magnesium at high temperatures. The proportion of the alloying elements was adjusted so as to obtain alloys with the desired magnesium content while maintaining a Cu-Ni ratio of 62 :38 by weight. (All alloy compositions will be given in weight percent.) Since it was considered desirable to study the oxidation of only single-phase, solid-solution alloys, it was necessary first to determine the approximate limit of solid solubility of magnesium in the 62 Cu-38 Ni alloy. A series of melts with various magnesium contents was made, homogenized by annealing for 48 hr at 975OC, then cooled in the furnace. Metallographic samples were prepared, etched in a potassium dichromate solution and examined at XI500 for the presence of a second phase. The alloys were then chemically analyzed and it was found that the approximate limit of solid solubility of magnesium in the 62 Cu-38 Ni alloy was 1 pct Mg. The ingots containing less than 1 pct Mg (0.19, 0.29, 0.58, and 0.87 pct Mg) were cold-rolled down to thicknesses suitable for oxidation experiments and specimens for gravimetric studies were cut to dimensions of 3.0 by 1.5 by 0.05 cm, specimens for inert marker studies, 0.6 by 0.6 by 0.17 cm. These were heat-treated in a protective atmosphere at a temperature (975" C) well above the oxidation temperatures and furnace-cooled to insure structural stability of the alloy during oxidation. Immediately prior to oxidation, the specimens were chemically cleaned by immersion for 1 min in a solution of 2 parts nitric acid, 1 part acetic

Jan 1, 1961

By C. F. Baes, H. H. Kellogg

The effect of dissolved sulphur on the surface tension of liquid copper has been measured by a sessile-drop method at 1120°C. Sulphur is highly "surface active" in liquid copper; the surface tension lowering is about 650 dynes per cm for a sulphur content of 0.6 pct. The degree of adsorption of sulphur on the liquid copper surface has been calculated, and various models of the surface layer have been tested against the results. THE science and technology of surface chemistry and physics at room temperature are relatively advanced, and the engineer possesses a background of information that allows him to predict and control many phenomena—such as frothing, emulsifica-tion, wetting of solids by liquids, flow through capillaries, adsorption, mineral flotation, penetration of porous bodies by liquids—which are related to the behavior at interfaces. Surface phenomena in high temperature systems are probably of equal importance to the metallurgist and ceramist, but at present are incompletely understood. Frothing of liquid slags, penetration of refractories by liquid metals and slags, infiltration of powder metallurgy "skeletons" by liquid metals, bonding of metals to ceramic oxides in the manufacture of "cermets," wetting of one metal by another for purposes of soldering and welding, are but a few of the many phenomena of metallurgy that are controlled by surface behavior. Concerning the most elementary of surface properties—the gas-liquid surface tension—the existing data on liquid metals are inadequate. For the surface tension of "pure" metals the results of different investigators differ by 10 or 20 pct. The role of surface-active agents in liquid metals is relatively unknown, and it is not unlikely that the discrepancy in the values for the surface tension of pure metals is due to the presence of traces of surface-tension-lowering impurities in the samples. Based on analogy to room-temperature systems, the highly surface-active impurities in liquid metals should be elements or compounds of limited solubility in the liquid metal and possessing considerably weaker in-termolecular bonding forces than the metal itself. The nonmetals of the V, VI, and VII groups of the periodic table might be expected to act in this way. The experimental work in this paper represents a study of the surface tension of pure liquid copper in hydrogen at 1120°C, and the effect of dissolved sulphur (which is a strongly surface-active agent in liquid copper) on the surface tension of copper. The Gibbs equation has been applied to the results and an attempt made to correlate the surface tension behavior with two models of the interfacial layer. The sessile-drop method for surface-tension measurement at high temperatures which was used in this investigation has been described by several investigators.1,2 It involves the measurements of the dimensions of a stationary liquid drop on a horizontal surface. From these dimensions and the liquid density, the surface tension of the liquid may be calculated either by means of various approximate formulas, or more accurately by means of the Bash-forth and Adams tables.- or liquid drops which exhibit a contact angle greater than 90°, by far the simplest dimensions to measure are those indicated in Fig. 1, i.e., the diameter of the maximum horizontal cross section (2X) and the maximum height (Z) above this plane. In order to calculate the contact angle and the volume of the drop, the diameter at the base of the drop (2a) and the total height (h) also must be measured. Upon investigation of the literature, the authors failed to discover a concise statement of the accuracy of the method when used in conjunction with the Bashforth and Adams tables, hence a careful examination of the tables was made and the curve shown in Fig. 2 was constructed. The "error factor," plotted as the ordinate, is the factor by which the

Jan 1, 1954

By Jacques B. Wertz

Among the parameters to be considered in the continuous search for new base-metal deposits, there often is a stratigraphic controlling factor that seems instrumental in the localization of ore. In British Columbia, for instance, the Upper Triassic as well as Lower Jurassic volcanics mixed with sediments are a useful indication in the search for copper while, in some parts of Australia, rhyolite bodies seem to be the favorable indicator, and this always within the geosynclinal environment. In Arizona, this stratigraphic factor becomes highly significant and it will be shown here that a large number of ore deposits are to be located around the flanks of ancient calcareous basins or depressions, preferentially corresponding to a certain optimum thickness as revealed by isopachs. The Martin limestone, of Devonian age, is already known for its basal O&apos;Carroll bed which coincides with mineralization at places, and this is a relatively minor control. However, several limestone basins outlined by isopachs are in reality of greater importance as they localize mining districts. Indeed, most mines are found to coincide with a specific thickness of limestone while occurring simultaneously close to major, regional fracture intersections. The regional fractures in question were interpolated and extrapolated from known, important fault expressions, integrating quite well with the existing geology and further confirmed by minor criteria such as contacts, igneous plugs, axes of elongation of batholiths, dikes, etc. Although elements of subjectivity remain, this grid of fractures can be used quite successfully as a working hypothesis in the search for ore. Results of the present study which superposes major structural

Jan 1, 1971

By T. S. Fuller

Various phases of the embrittlement of solid copper containing oxygen by the action of reducing gases at high temperatures are familiar to readers of metallurgical literature through the work of many experimenters. In 1900, Heynl recorded observations of copper being heated in hydrogen with the development of fine cracks, the result of the formation of steam within the metal through the action of hydrogen on the copper oxide usually found in copper. Archbutt,2 in 1905, published the results of experiments, showing that all oxygen can be removed from copper by heating to redness, for several hours, in hydrogen. Intercrystalline cracks and extreme brittle-ness developed. Archbutt attributed the brittleness to the reduction of oxides present in the copper. Bengough and Hil1,3 in 1910, encountered the now well-known embrittlement at the outset of their investigation and stated in their paper: It soon became evident that the effect of any heat treatment depended largely on the presence or absence of reducing gases in the atmosphere of the furnace, as well as on its temperature. Hence it became necessary to adopt a somewhat elaborate scheme of heat treatment. The authors found embrittlement in separate experiments due to both hydrogen and carbon monoxide and concluded that: "The gases ruin the alloys after being heated to about 650" C. in their presence." Ruder,4 in 1916, reported the results of a series of experiments made by heating commercial and deoxidized copper in hydrogen, carbon monoxide, carbon dioxide, and steam. In agreement with other writers, he found that copper containing oxygen was made brittle by reducing gases, while the deoxidized metal remained unaffected. In the case of

Jan 1, 1926

By L. L. McDaniel

Copper smelters of various kinds have operated in the Morenci district since 1872, but all have been abandoned with the exception of the present Morenci Smelter of Phelps Dodge Corporation, which was completed in 1942. During the five-year period starting in 1937, the Morenci ore body was prepared for open pit mining, pilot mill test work was carried out, and a complete reduction works, of which the Smelter is a part, was designed and erected. Actual construction work on the Morenci Smelter was started in the fall of 1940, and warming up of the units began on April 1, 1942. Charging of the reverberatory furnaces commenced on April 18, 1942, and the first anode copper was produced on April 26, 1942. The smelter was originally designed to handle the production of the Morenci Concentrator on a 25,000 ton per day program, but by the time the smelter was in operation, plans were already underway to increase the smelter capacity to handle the production of the concentrator which was being enlarged to 45,000 tons a day capacity as a war-time necessity. This extension to the smelter was completed and the new units were put in operation toward the beginning of 1944. The original smelter consisted of a smelter crushing plant, bedding plant, two direct-smelting reverberatory furnaces with two waste-heat boilers on each furnace, three converters, an anode department, a stack, and all of the usual accessory smelting equipment. The extension consisted of increasing the bedding plant from three to five beds, the reverberatory department from two to four furnaces, and from four to eight waste-heat boilers, and the converter department from three to six converters. A third converter aisle crane was added and additions were made to the flue systems and conveyor systems throughout the smelter; but no change was made in the smelter crushing plant or the anode department, and the same stack was used for all additional Smelter units. A blister casting machine was installed at that time in the south end of the converter aisle to handle excess and emergency production above the capacity of the anode department and in 1947 a converter aisle skull breaker and a lime burning plant were added as the final units for a complete plant. The choice of direct smelting over calcine smelting for the Morenci Smelter was made after careful study by members of the Western organization of Phelps Dodge Corporation and after test runs on direct smelting of Morenci concentrate had been made at the Douglas Smelter of Phelps Dodge Corporation. The Morenci furnace charge is made up of comparatively high grade concentrate with no ores of smelting grade available and with only flux, a small amount of copper precipitate and the usual amount of smelter secondaries to be smelted with the concentrate. The simplicity of direct smelting for this charge and the large amount of waste-heat steam available from direct smelting operations were factors influencing the decision to adopt direct smelting for Morenci. The design of the Morenci Smelter and the type of units selected followed best experience at the Douglas Smelter of Phelps Dodge Corporation. A description of the original smelter before operations started was given in an article in the May 1942 issue of Mining and Metallurgy. The purpose of the present article is to describe the enlarged Morenci Smelter, with a discussion of metallurgy and operating practice and to show tabulations of operating and metallurgical results obtained. Because of beginning operations during the early years of World War 11, many problems caused by labor shortage were encountered, but no major difficulties developed in starting the new plant. However, because of labor shortage, full scale Smelter production was not reached until the fall of 1946. Fig 1 shows a general plan of the Morenci Reduction Works. The arrangement of the smelter equipment is shown in Fig 2, a sectional view of the smelter is shown in Fig 3, and the smelter flow sheet is shown in Fig 4. Metallurgy The metallurgy of direct smelting, being more or less fixed by the character of the charge, is not subject to the control available in calcine smelting. Slags may be modified by the addition of suitable fluxes, but the grade of the matte is determined almost entirely by the iron:copper ratio of the concentrate. The direct smelting operation involves distributing the wet concentrate along the sidewalls and in the bath of a reverberatory furnace by means of some suitable feeding device and raising the temperature of the charge so that first the moisture is driven off, then the first-atom sulphur is eliminated, and finally the sulphide portion of the charge melts and runs into the bath, carrying with it the non-sulphide portion which has been partially fluxed to form a suitable slag. The fusion of the non-sulphide portion is completed by contact with the irony converter slag which is regularly being poured into the reverberatory furnace. The smelting rate of the charge is influenced by the mineralogi-cal composition of the sulphide portion of the concentrate and by the composition and amount of the non-sulphide portion including the fluxes added. The copper in Morenci concentrate is chiefly in the form of chalcocite, intimately associated with pyrite, and non-sulphide content is very low so that

Jan 1, 1950

October 16th, 1872. THE Institute assembled on Wednesday evening at the Western University, and was called to order by President Raymond. Mr. James Park, Jr., of Pittsburgh, made the address of welcome, which was responded to by President Raymond. The Council reported the following names, with approval, for election Ashburner, William, - San Francisco, Cal. Asmus, George, - New York. Baillie, Nathaniel, - Uniontown, Pa. Bowie, A. J., Jr. - San Francisco, Cal. Brown, A. J., - Treasure City, Nev. Butler, J. G., Jr., - Youngstown, Ohio. Chamberlin, J. G., - Leetonia, Ohio. Clark, R. Neilson, - Canyon City, Colorado. Cornell, A. B., - Youngstown, Ohio. De Crano, E. G., - San Francisco, Cal. Engelmann, H., - Salt Lake City, Utah. Faber du Faur, A., - New York. Janin, Louis, Jr., - San Francisco, Cal. Johnson, George J., - Salt Lake City, Utah.. Kent, Joseph C., - Phillipsburgh, N. J. Kent, William St. G., - Phillipsburgh, N. J. Liebenau, Charles von, - Silver City, Idaho. McClintock, A. H., - Wilkes-Barre, Pa. Miller, Thomas N., - Pittsburgh, Pa. Millholland, James A., - Mount Savage, Md. Peters, Ed. D., Jr., - Dudley, Colorado. Reese, Jacob, - Pittsburgh; Pa. Schirmer, J. F. L., - Denver, Colorado. Smith, W. S., - Fairplay, Colorado. Stoelting, Hermann, - Georgetown, Colorado. Sweet, W. A., - Syracuse, N. Y. Tripple, Alexander, - New York. Van Arsdale, W. H., - Swansea, Cal. Willard, Dwight D., - Bordentown, N. J. The following resolution was then offered and passed Resolved, That gentlemen present, not members, be invited to take part in the discussions of the Institute at the various sessions of the present meeting.

Jan 1, 1873

By K. Takahashi, I. Iwasaki

The methyl stretching vibrations for a series of normal xanthates, isoxanthates and normal amines were determined with the aid of an infrared spectro-photometer, and the results were compared with published information on the corresponding alcohols. The frequency shifts of methyl stretching vibrations may be attributed to the inductive effect of polar groups. The hydrogens in the shorter chain alkyl groups are somewhat polar and can be expected to interact with water molecules by hydrogen bonding. Contact angle, surface tension lowering, solubility, and critical micelle concentration appear to be related to the induced polarity of the alkyl groups. Traube&apos;s rule states that in homologous series of compounds solubility decreases and surface activity increases regularly with the size of the hydrocarbon group. Analyzing the work of transfer of a solute from solution to surface, Langmuir&apos; interpreted this rule to mean that each CH2 group added to a molecule produced its effect independently of the others. It is also well known2 that the maximum equilibrium contact angle with sulfhydryl collectors is independent of the polar groups and of the sulfide minerals, and that it increases to a certain limit with the number of carbon atoms in the alkyl group. This observation is thought to demonstrate the orientation of the collector molecules at the sulfide surfaces. The dependence on the hydrocarbon chain length is usually explained as due to the screening of the force field of polar mineral surfaces.3-5 Here again, Langmuir&apos;s principle of independent surface action appears to be implied. Heteropolar compounds consist of nonpolar and polar groups, the former being the hydrocarbon group and the latter containing such electronegative atoms as O, N, S, P, or halogens. According to Palit6 the hydrogens in the alkyl groups are more electroposi- tive than in the paraffins owing to the negative inductive effect of the polar groups and a possibility that a hydrogen bond with water molecules ensues. Goto and Takenaka7 provided direct evidence of the inductive effect by measuring the shift of the C-H stretching vibrations of alcohols, acids, and alkyl bromides with an infrared spectrophotometer. Their approach appeared to be directly applicable to the studies of surface activity both at air-water and water-mineral interfaces encountered in flotation systems. The present article attempts to relate the C-H stretching vibrations of alkyl xanthates, alcohols, and amines with such flotation chemistry parameters as contact angle, surface tension lowering, solubility, and critical micelle concentration. MATERIALS AND METHODS Normal xanthates from methyl to octyl inclusive and the isopropyl, isobutyl, and isoamyl xanthates used in this investigation were prepared in the usual manner.8 Normal amine hydrochlorides with carbon chain lengths of 1, 2, 4, and 6 were from Distillation Products Industries, of 8 from Archer-Daniels-Midland Co., and of 10, 12, 14 and 16 from Armour and Co. Normal propylamines, pentylamines and heptylamines from Distillation Products Industries were used both as received and as hydrochloride formed by converting the amines according to the procedure described by Li9 Perkin-Elmer Model 521 and 621 infrared spectro-photometers were used to investigate the spectra in the frequency region of 3050 to 2800 cm-&apos; with frequency scale expansion. The accuracy of the frequency readings was within + 1 cm-1. The KBr micropellet technique was used to prepare the xan-thate samples for measurements, and the halocarbon mull technique was used for amines and amine hydrochlorides. EXPERIMENTAL RESULTS Fig. 1 shows the CH3 asymmetric stretching vibrations as a function of the number of carbons in the alkyl group for normal xanthates, isoxanthates and amines. Also included in the figure are data for normal alcohols and isoalcohols taken from the article

Jan 1, 1970

By B. A. Wilcox, A. H. Clauer

The tensile and creep deformation characteristics of fiber reinforced composites have been studied, primarily at room temperature. The matrix was an alloy of Mg-14 wt pct Li-1 wt pct Al (LA141A alloy) and the reinforcing fiber consisted of continuous wires of a high strength precipitation hardening stainless steel (AFC-77 alloy). The ultimate tensile strength and strength-to-density ratio of composites were much improved over that of the mmix, both at room ternperatwe and up to 200°C. Creep studies at room temperature revealed logarithmic weep behavior for wires and composites and steady state creep for the nonreinforced matrix. It was concluded that creep of the fibers controlled composite creep. The instantaneous logarithmic weep rate of the composite, 6, was related to the average tensile stress on the fibers, where n = 3.4. Mg-Li alloys are the lightest structural metals commercially available, e.g., the alloy LA141A (Mg-14 wt pct Li-1 wt pct Al) is 27 pct less dense than beryllium Although Mg-Li alloys have moderate tensile strengths at normal strain rates and ambient temperature, their creep strength is relatively poor, even at room temperature. Reinforcement by fibers offers a means of increasing the tensile strength as well as overcoming the limitations of low creep strength. With a proper choice of reinforcing filament, composites could be designed with higher strength-to-density and modulus-to-density ratios than the matrix alloy. This communication reports a study on the tensile and creep characteristics of alloy LA141A reinforced with continuous wires of a high-strength precipitation hardening stainless steel (AFC-77 alloy). The matrix has a bcc structure, with possible precipitates of AlLi and MgLi2A1,3 and is ductile at room temperature Stainless steel wire was chosen as the -reinforcing filament since previous work at Battelle4 showed that a good bond between wire and matrix could be produced in this system. For all volume fractions of reinforcing wire, the theoretical composite strength-to-density ratio is greater than that of the matrix and the modulus-to-density ratio is somewhat lower than that of the matrix. EXPERIMENTAL PROCEDURES The 0.004-in. diam AFC-77 wire was obtained from two suppliers: National-Standard Co.* and Crucible 0.13 Si, 0.18 V, 0.011 P, 0.012 S, balance Fe. In the as-received condition, wires from both sources had room-temperature ultimate tensile strengths of 585,000 to 590,000 psi with approximately 2 pct total elongation and 40 pct reduction in area. Composite preparation was accomplished by the vacuum infiltration technique. This involved placing the continuous wires in a mild steel tube (1/8-in. ID), capping one end of the tube with a sheet of the matrix alloy, and evacuating the other end of the tube. When the capped end was placed in a crucible of the molten matrix alloy and held for 31/2 min at 70O°C, the liquid metal was drawn up the tube approximately 7 to 8 in. A cross-sectional view of a typical composite is shown in Fig. 1. This preparation technique promoted excellent bonding between the matrix and wires, and porosity was rarely observed. Test specimens for both creep and tension studies were prepared by machining off the steel tube. Tensile tests on the wires and composite specimens were made in an Instron using a cross-head speed of 0.01 in. per min. The composite specimens had no reduced section and were held in self-tightening grooved serrated grips. Most of the specimens broke in the effective 1-in. gage section. Even though several tests fractured in the grip section, their ultimate strengths were essentially the same as those of specimens which fractured in the gage section. Creep specimens of the composite were gripped in a similar manner, and

Jan 1, 1970

By B. Ancker, E. R. Parker

The small-angle dislocation-boundary density of nickel and some of its alloys was investigated as a function of strength. It was found that the strength is a linear function of the density for pure nickel and for Ni-Ti alloys, but not for Ni-Co alloys. The results are interpreted in terms of dislocation theory. THE processes by which metals deform are still poorly understood, even though there has been a concentrated research effort in this field during the past fifteen years. Single crystals and individual grains in polycrystalline aggregates often develop a subgrain structure when deformed. Substructure formation occurs as a result of local plastic bending and its development is augmented by annealing at moderate temperatures.&apos; Investigations made to date, largely qualitative in nature, have shown that the substructure is composed of a network of small-angle boundaries. The purpose of the present paper is to present some quantitative data on substructure (obtained by X-ray techniques) and to correlate the results with the strength of the metal in which the substructure existed. Nickel and some of its alloys were used for the experiments. The presence of certain kinds of foreign atoms greatly alters the formation and effect of the substructure. Polycrystalline tensile specimens were prepared from high purity nickel, two Ni-Ti alloys, and two Ni-Co alloys; the composition of these materials is given in Table I. Tensile specimens having a reduced section 1/4 in. diam by 3 in. long were machined from materials which were refined, cast, forged, and swaged in the authors&apos; laboratories. The specimens were annealed for 1/2 hr at 1150°C, a treatment which produced grains having a diameter of approximately 0.5 mm. This rather large grain size was used to facilitate later examination of the substructure. Duplicate specimens of pure nickel and of each alloy were strained various controlled amounts in tension at room temperature and recovered for 1 hr at 800°C. (This strain induced prior to recovery will be referred to hereafter as the "prestrain.") One of each of the recovered specimens was pulled in tension at room temperature to obtain the stress-strain curves. The other bar was cross-sectioned in the gage length, carefully polished, and deeply etched to remove all cold-worked material. This specimen was then examined by the X-ray microscopic technique2 to determine the nature and magnitude of the substructure. The use of duplicate specimens permitted a direct correlation between tensile properties and substructure characteristics. X-ray microscopic studies were made with an apparatus constructed to have an average resolving power of about 4 microns. The monochromatic radiation reflected from grains which were oriented favorably was recorded on fine-grain photographic plates. These were examined at Xl00 which represents the true magnification, since there was essentially none in the X-ray system. This permitted detection of angular differences between subgrains of as little as 10 min. A very large number (over 100) of grains for each specimen was examined at this magnification and the number of substructure boundaries per grain was tabulated. An accurate relative measure was obtained under fixed experimental conditions, e.g., same grain size, resolving power, magnification, etc. The greatest source of error lay in counting the subboundaries, but this proved to be surprisingly small when repeated counts were made by different investigators. Furthermore, as the subsequent analysis indicates, whatever human error was introduced was not significant. Analysis of the Substructure Data When the number of substructure boundaries per grain was plotted against the frequency, skew (asymmetrical) distribution curves of the type shown in Fig. 1 were obtained. These are smoothed curves for the 1 atomic pct Ti in nickel alloy subjected to various prestrains and are representative of the curves obtained with all the metals. Since skew-distribution curves cannot be analyzed by elementary statistical methods, detailed investigations were undertaken in order to 1—test the consistency

Jan 1, 1955

By W. H. Bassett, J. C. Bradley

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (I) Depth of deoxidation of copper heated in reducing gas is grealer the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this diflerence in depth of deoxidation is thai, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much more rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900" C.; that is, deoxidaion is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide presenx in the copper. In 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

By Sherwin F. Kelly

Drilling in the Oligocene potash basin of Alsace prior to 1927 had shown important differences of level in the salt beds thus encountered. TO explain this a somewhat unsatisfactory hypothesis of faulting had been advanced. During the latter part of 1926 and the beginning of 1927 our firm was engaged by two organizations1 for the purpose of trying to supplement, by an electrical survey, the geological data this far collected. As a result of this exploration it was possible to affirm that salt dome structures were present in the Oligocene basin of the Upper Rhine, something heretofore absolutely unknown in that region. Two salt domes were actually outlined: one, near Meyenheim, was made the subject of a communication to the Academy of Sciences, by G. Friedel;2 the other, near Hetten-schlag, was briefly discussed by C. and M. Schlumberger3 before the same academy. The purpose of this paper is to indicate the stratigraphic and structural conditions of the area where these salt domes were found; to discuss the results of the electrical survey which led to the location of the domes; and to indicate the new geological outlookwhich such a discovery suggests. Stratigraphy In the southern part of the Rhine graben the Oligocene rests almost directly on the Middle Jurassic and consists, in ascending order, of: 1. Green marls, not salt-bearing, composed of fresh and brackish water deposits. 2. Middle stage, salt-bearing, consisting of lower-schistose marls and upper, variegated marls. 3. Blue marls, not salt-bearing, but including gypsum deposits; hence sediments laid down in a bay more or less connected with the sea.

Jan 1, 1929

By Anthony Sharkey

Introduction In Europe, longwall mining accounts for over 95% of coal produced from deep mines, whereas in the U.S.A., longwall accounts for less than 5% of deep mine coal production. There are many reasons for the difference, but in general: a. U.S. mine operators have invested heavily in continuous mining or conventional equipment which continues to produce acceptable results; b. There 1s a reluctance to change from, a familiar (and proven) mining method to an unfamiliar one, despite promises of huge production increases,; c. Multi-seam mining in Europe has made longwall the only really viable mining method, whereas In the U.S.A. multi-seam mining (particularly in "below-drainage" mines), is relatively rare; d. Although some spectacular results have been achieved by longwall in the U.S.A.(I), the general performance of longwall in this country has not been good enough to generate much enthusiasm for its wide application; e. The much higher level of investment in face equipment required for longwall when compared to alternative methods (approximately $7.5 million for a medium seam longwall installation and $1 million to $1.5 million for a continuous miner section). However, declining productivity, national energy requirements and safety legislation are creating a situation in which longwall as a viable mining method is being examined more closely and in more places than hitherto. This paper, therefore, attempts to identify some of the principal criteria needing examination in any assessment of the feasibility of longwall application, the limitations of information for those criteria in the decision making process and the need for further research and development to assist the mine operators make the decisions.

Jan 1, 1981

By Hertha Freche

THE diffusion of magnesium and silicon from the core into the high-purity coating of Alclad sheet is important commercially, and led to the use of a duplex product for the study of diffusion by means of spectro-graphic analysis of successive layers. It has been found that in the duplex materials the diffusion of magne-sium from an undersaturated aluminum-magnesium alloy into its high-purity aluminum coating is approximately of the same order of magnitude as the diffusion of silicon from a saturated aluminum-silicon alloy into its high-purity aluminum coating. However, if magnesium and silicon are both present in the alloy in the ratio of Mg2Si they appear to diffuse in the approximate ratio of this compound. Finally, if the alloy contains silicon in excess of the amount required by magnesium silicide, the amount of diffused silicon in the high-purity aluminum coating will also be in excess. The interdiffusion of metals in the solid state is of both scientific and technical interest, because it is helpful in the study of the alloy structure and in the solution of problems pertaining to the strength and surface condition of the fabricated product. W. C. Roberts-Austen1 carried out the first quantitative determination of the coefficient of diffusion of gold into lead. This classical experiment was followed by a series of investigations on the diffusion of metals and nonmetals in iron and steel and in nonferrous metals and alloys. Recently the diffusion of copper in coated strong aluminum alloys was investigated by A. Burkhardt2. This appeared to be the first published investigation on the diffusion of metals into aluminum.

Jan 1, 1936

By J. A. Roberson, A. M. Adair

A plate of an 18 pct Ni (250 grade) maraging steel was homogenized, cold rolled, and re crystallized to produce a fine grained, homogeneous structure. The strength properties were then measured as a function of cold rollinq prior to aging. Material in the solution heat treated condition exhibited substantial strengthening from cold rolling. The strength increase and the rate of strengthening were proportional to the amount of cold work. This benefit, of up to 50 ksi, was retained during aging for 3 hr at 900°F. The structures produced by cold rolling and aging have been systematically investigated by transmission electron microscopy. The dislocation debris produced by cold work influences the morphology and distribution of precipitate particles as well as the rate of precipitation. An essential feature of the high nickel maraging steels is a martensitic transformation from y to a with the resultant production of a supersaturated bcc solid solution. This solution decomposes to form precipitates during a subsequent aging treatment.&apos; The martensitic transformation in low carbon Fe-Ni alloys and the mechanical properties of these alloys have been studied extensively.2"4 The carbon content of maraging steel is kept very low to avoid the embrittling Fe3C phase and to minimize the acicular, or twinned martensite common to high carbon steels. Maraging steels are usually strengthened only by heat treatment, but cold working is also quite effective in this respect as was shown by Decker, Eash, and Goldman,&apos; Kula and Hickey,5 and the present work. There is, however, some disagreement between the present results and those of Kula and Hickey. Because of their unusual combination of strength and toughness, the maraging steels are suitable for applications where reliability at high stress levels is required. The strength level is achieved through a combination of solid solution hardening,&apos; substructure hardening,3 and precipitation hardening,6 of which the last is the most important. The toughness of these steels has been reported to be a result of the absence of brittle grain boundary precipitates,7 and the fact that the matrix is a massive martensite rather than a twinned martensite.&apos; One of the problems in the manufacture and use of maraging steel has been its tendency to develop laminations in sheets parallel to the rolling plane.9,10 The present investigation was intended to determine whether or not an improvement in the microstructure of this steel by thermomechani-cal processing would improve mechanical properties. I) EXPERIMENTAL PROCEDURES A plate ($ in. thick) of an 18 pct Ni-250 grade maraging steel* was obtained and examined metallo- "Analysis, wt pct: 18.1 Ni, 8.6 Co, 5.3 Mo, 0.4 Ti, 0.07 Mn, 0.05 Cr, 0.05 Si, 0.002B. 0.1 Cu. 0.05 Al. 0.002 Zr, 0.016 C, balance Fe. graphically. It was found to contain laminations as described by previous investigators. This plate was then annealed at 2100°F for 24 hr to promote homogeneity. Pilot studies on small coupons had shown that this was the minimum temperature required to accomplish homogenization in 24 hr. Since this treatment caused excessive grain growth, the steel was subsequently cold rolled and recrystallized. Cold rolling was accomplished at about 5 pct per pass to a total reduction of 66 pct. The standard solution annealing treatment (1 hr at 1500°F) was adequate to cause recrystallization of the cold worked steel. The recrystallized steel was then cold rolled and ground by various amounts to produce specimens with uniform thickness and selected amounts of cold rolling. All tensile specimens with less than 90 pct cold reduction were ground to a thickness of 0.050 in. Specimens with 90 pct cold reduction were 0.025 in. thick. All

Jan 1, 1970

By F. D. Rosi, C. H. Mathews

THE plastic properties of face-centered cubic metals below room temperature present a field of investigation which has not been extensively ex-plored. The work by Schmid and Boas1 has demonstrated the importance of temperature upon such properties as strain hardening and critical resolved shear stress. The work by Yamaguchi2 upon the shear stress as related to the number of slip bands accentuates the necessity for further experiments of a similar nature. The approach to a mechanical equation of state from the standpoint of thermal fluctuations and activation energies by Becker3 and more recently by Kauzmann4 further emphasizes the need for a quantitative and more comprehensive analysis of the dependence of fundamental plastic properties on temperature. The purpose of the present work was to investigate specifically: (1) The gross shape of the stress-strain curves at several temperatures, (2) the change in the critical shear stress as a function of temperature, and (3) the number and appearance of slip bands as a function of strain and temperature. Preparation of Specimens Single-crystal specimens of 99.996+ pct alumi-num, 1/2 in. in diam and 5 to 6 in. in length, were made by the Bridgman method of gradual solidification from the liquid state. The crystallographic orientation of the single crystals was determined from back-reflection, Laue X-ray photograms ac-cording to the method described by Greninger.6 In most specimens the Laue photograms showed double diffraction spots indicative of the lineage structure type of imperfection, discussed in great detail by Buerger.7 The angular spread of these spots was never observed to exceed 2". Most of the crystals were radiographed to insure against microporosity. In preparing the metal surface for optical microscopy, the following sequence of operations gave good results: The as-cast crystals were turned down in a lathe, 0.001 in. per cut, to obtain a 2.5 in. gauge length. The cold-worked layer resulting from this operation was removed chemically by etching with Tucker&apos;s reagent. Then the specimen was polished mechanically through 2/0 metallographic emery paper, after which it was etched again to remove the cold-worked layer resulting from the mechanical treatment. A 48-hr anneal at 580°C ±10°C followed so as to insure an essentially stress-free single crystal. After the annealing treatment, the specimen was electrolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. With a current density of 10 amp per sq dm (decimeter) the time required to obtain a satisfactory surface varied from 10 to 12 min. The polish-ing was carried out for short periods of 2 min to avoid rapid deterioration of the solution as well as to enable the rotation of the specimen 180" for uniformity of polish. It was necessary to place the solution in a bath of dry ice in view of its explosive nature at room temperature. Etching of the electrolytically polished surface was accomplished by using the fuming etch-pit method recommended by Lacombe and Beaujard8 for high-purity aluminum. Method for Tensile Testing A modification of the loading equipment devised by Miller9 was used. In this apparatus, the specimen was suspended from a chain and gimbal arrangement (for axial loading) in a heavy steel framework connected at the bottom to a balanced 6:1 lever and bucket system. Loading of the specimen was accomplished by allowing sand to flow from a reservoir into the bucket suspended from the longer end of the lever-arm at a rate of approximately 3 lb per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire, strain gauge and an SR-4 portable strain indicator (type K), which permits a reading accuracy of 2 microinches per inch. For low-temperature study, the gauge was calibrated by measuring the elastic modulus of an annealed stainless steel rod, which is known to be independent of temperature."

Jan 1, 1951

By I. S. Levy, J. L. Brimhall, B. Mastel

Specimens of&apos; Hastelloy X-280, a low-cobalt version of the solid-solution- hardened nickel-base alloy Hastelloy X, were given a series of thermomechanical treatttzents. They were then Lensile-tested at room temperature and 1350°F. The Microstructures of the specimens tested at 1350°F were studied by electron Microscopy. Microscopy showed that dislocation tangling, caused by the cold working, mas still in evidence after aging-for 24 hr to temperatures as high as 1550oF. (Cr, Mo)23 C6, (Fe, Mo)6 C&apos;. as well us an unidentifiable phase precipitale due to the combination of the thermomechanical treatments and subsequent tensile strain. The room -temperature and 1350°F tensile properties show a general increase ill strength and decreccse in ductility with increusing cold-work level. This is due to the dislocation taangling-. PerLurbatiot~s to this general trend occur- due to solid-solution weakening at the higher cold-work levels as a direct result of the preciplitation reactions. THE requirements for corrosion resistance and high-temperature strength place nickel-base alloys among the more promising materials for advanced nuclear reactor applications. However, when these alloys are irradiated at service temperatures, they generally suffer severe embrittlement&apos;" and reduction in rupture life.3 Certain experimental treatments resulted in improvements in the tensile and stress-rupture properties of Hastelloy X-280, a solution-hardened nickel-base alloy.&apos; To provide a basis for understanding these improvements, unirradiated tensile specimens were examined by electron microscopy. The results are reported in this paper. EXPERIMENTAL DETAILS Material. Hastelloy X-280, a low-cobalt version of Hastelloy X, is a member of the solution-hardened class of nickel-base alloys. The Hastelloy X-280 was obtained from 4- and 1-in: thick plates in the mill -annealed condition. Table I gives the chemical composition of the material as reported by the National Spectrographic Laboratories. ~x~erimental Treatments. Plates of suitable size, 12 by 3 by 1 in., or by + in., were cut under a water jet from the stock material and examined ultrasonic -ally for homogeneity of grain size and absence of voids. The acceptable plates were solution-treated at 2150°Ffor 1 hr and air-cooled. These plates were then reduced in thickness by cold rolling 0, 10, 15: or 20 pct along the original rolling direction. The plates were machined into buttonhead tensile specimens with a gage diameter of 0.125 in., with a gage length of 1.125 in., and with their tensile axes parallel to the rolling direction. The specimens were examined for quality of finish with a penetrant dye, ultra son ically checked for voids, and finally given a dimensional tolerance check with an optical comparator. The acceptable specimens were aged for 24 hr at either 1000" or 1500 F and air-cooled. These specimens were then held at 540°F in a water loop for approximately 18 days to qualify as controls for similar specimens irradiated under the same conditions of time, temperature, water chemistry, and flow rate. Table U summarizes the treatments. These treatments were investigated to establish whether prior precipitation and stabilization of carbide phases at strain sites within the matrix could reduce the amount of carbides available for precipitation at grain boundaries during service. Tensile-Test Conditions. Specimens were tested to fracture at room temperature or 1350 F in air on an Instron tensile-testing machine at a crosshead speed of 0.05 in. per min. The time for the furnace to reach equilibrium at 1350°F was approximately 30 min; soak time prior to testing was 15 min; and test duration was approximately 5 min.

Jan 1, 1968

By W. J. Rogers, L. J. Dwiggins, R. O. Williams

THERE has been comparatively little work on the importance of strain rate and temperature as variables in the formation of deformation textures. For this reason the present work was started, the choice of compression being in part that of convenience and in part because of the absence of quantitative data in this area. These do not turn out to be important variables within the range studied which permits the results to be condensed into this note. Samples 1/4 in. in diam and 1/2 in. long were machined from 99.9 pct pure commercial aluminum and recrystallized to a fine grain size. A set of five samples were deformed between a spring-driven weight and an anvil resulting in roughly 20 pct strain each time. The strain rate varied because of decle-ration and shortening of the sample but would average about 10&apos; per min. Deformation at temperatures over the range of -76" to 150°C were obtained by heating or cooling the samples. Complete lubrication could be obtained by oil since the short time of contact did not permit its escape. The samples were compressed to a total true strain of 1.4 to 1.6. A larger sample was prepared similarly with spiral grooves in the ends to hold paraffin which provided essentially complete lubrication. This sam ple was compressed slowly at room temperature at a rate of about 2 per min to a total strain of 1.0. Cylindrical samples were carefully machined from these discs with a radial direction as an axis. They came from the center half of the samples and were roughly 1/16 in. in diam. The samples were etched down 15 pct to remove any surface effects. Diffraction data were then obtained for six different kinds of planes by the use of the Norton technique as applied to a fiber texture. Direct comparison between the raw data failed to reveal any significant difference between any of the samples and consequently the data from only one sample was completely reduced. The particular sample had been deformed at O°C The background was subtracted from the intensity data which were averaged over the four quadrants and then normalized to random. These data were then used to obtain fiber-axis distribution charts as previously described.2 For this sample the (422) plane was also run to assist in this inversion. The final result, Fig. 1, provided a comparable fit to that previously obtained from fiber data. About 85 pct of the material forms an elliptical texture around the <110> direction. The radius (at half height) is 5.5 deg along the (111) boundary and 8 deg along the (100) boundary. The remaining 15 pct forms a ridge running from this texture to near the <311> direction. The regions around the (100) and (111) planes are devoid of material. The earlier qualitative results of ~arrett~ are in complete agreement with the present results. The possibility has been dis-cused that the material around the <311> results from friction between the sample and compression plates.4 The present results are considered proof that such is not the case because of the uniformity of sample deformation and the requirement of axial symmetry before fiber-axis distribution charts can be accurately obtained. Recently results have been obtained to show that strain rate and temperature are important variables in the extrusion of aluminum.5 Perhaps the most important observation was that the partial recrystal-lization occurred even at room temperature. Strain rate was considered to be a factor only in that it produced a temperature change. There are many differences between the two experiments, the most important possibly being that their material was roughly ten times the purity of the present material. The present experiment, however, may not be as definitive as desired in this respect since it has been shown that compressed aluminum recrystallizes without a texture change6 although supplementary

Jan 1, 1961

By A. Eilers

A number of the copper refineries in this country have lately separated some of the rarer metals from the slimes in the refinery tanks. One of these has furnished me the following table of recoveries from given amounts of blister. I publish this to show the proportions, to gold and silver and to each other, in which these rarer metals may be expected to occur in copper from certain localities. GarFIeld, Utah :—The blister copper comes principally from the Bingham porphyry copper mines. Steptoe, Nev. :—All the blister copper is produced from the Nevada Consolidated mines. (Also porphyry deposits.) Omaha, Neb. :—Blister copper comes principally from concentrated copper-lead mattes shipped from the different lead-silver plants of the Rocky Mountain region to the converters at the Omaha lead refinery. Mountain, Cal. :—Ores occur in connection with diorite (?).

Jan 1, 1914

The resin-in-pulp (RIP) ion exchange process was originally conceived by the Atomic Energy Commission in the early 1950&apos;s. However it was developed to commercial success by the Anaconda Co. at its 3000-tpd ore processing mill in Grants, N. M. Essentially, the Anaconda mill&apos;s crushing, grinding and acid leaching operations are the same as at the nearby Kerr-McGee mill, except that Anaconda uses manganese dioxide instead of sodium chlorate as oxidant during acid leaching. The real differences between the two mills become evident when considering how Anaconda treats its leached materials.

Jan 8, 1974