Search Documents

By E. E. Donath

THE coal hydrogenation process is well known as a means for the production of liquid fuels -from coal. In this paper the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid phase and vapor phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high molecular weight aromatics and of tar acids and tar bases. The relative amounts of heavy and middle oil-boiling above and below, e.g., 325°C-can be influenced by temperature, residence time, and catalyst of the liquid phase hydrogenation. In the vapor phase hydrogenation a solid bed catalyst is used to convert the intermediate oil from the liquid phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring compound content of the liquid phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparaffins.1 Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig. 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid phase hydrogenation stage, coal is made into a paste with recycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydro¬gen enter high pressure converters where the liquefaction of coal, conversion of the high boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470°C. The reaction products enter the hot catchpot in which lower boiling oil vapors are separated from the residue containing unreacted coal, ash, and heavy oil. This residue, usually called H.O.L.D. (heavy oil let down), is processed to separate solid and liquid material. By thermal treatment of the residue, e.g., a coking process, distillate oil is obtained, which can be recycled as part of the pasting oil. This stream is rich in polynuclear aromatics and can be, and has been, used for the recovery of such material. The oil vapors and hydrogen from the hot catch-pot are cooled in heat exchangers and a cooler, and the condensed oil is separated from the recycle hy-

Jan 1, 1952

By Thomas M. Drown

Remarkable as have been the direct results of Danks's puddler, there are some indirect and incidental results, which are well worthy of study for their intrinsic value and suggestiveness. The success of Danks's machine is due mainly to the nature of the lining and the manner in which it is attached to the walls of the revolving chamber. Herein lies Danks's merit and good fortune. Given such a lining, and the success of the machine, as far as puddling iron is concerned, could easily be predicted. Other important results have, however, been obtained with this machine, which, though clearly explicable, were, nevertheless, unanticipated. These are the increased yield of bar-iron over the pig-iron charged, and the elimination of phosphorus, which, though not absolutely complete, is yet more decided than in the case of hand-puddling. As regards the increased yield, this is merely what we have a right to expect if we consider the puddling process to consist in the oxida tion of the carbon and silicon of the pig by the oxygen of the oxide of iron. That this result is attained, nearly to the extent that the theory requires, in Danks's puddler, and has never been more than partially attained by the most careful experiments in band-puddling, points clearly to the fact that the contact of the molten pig-iron with the oxide of iron is much more intimate and complete in the one instance than in the other. The action of puddling in Danks's machine may be considered to be twofold: first, the removal of the carbon, silicon, and phospho rus of the pig, which is the primary object, and, second, the produc tion of wrought iron direct from the ore, which is entirely an inci dental result. Intelligent metallurgists were not long in recognizing in this latter result a fact of deeper import and greater value than the attainment of a perfect puddling process. A new method

By Thomas M. Dr. Drown

REMARKABLE as have been the direct results of Danks's puddler, there are some indirect and incidental results, which are well worthy of study for their intrinsic value and suggestiveness. The success of Danks's machine is due mainly to the nature of the lining and the manner in which it is attached to the walls of the revolving chamber. Herein lies Danks's merit and good fortune. Given such a lining, and the success of the machine, as far as puddling iron is concerned, could easily be predicted. Other important results have, however, been obtained with this machine, which, though clearly explicable, were, nevertheless, unanticipated. These are the increased yield of bar-iron over the pig-iron charged, and the elimination of phosphorus, which, though not absolutely complete, is yet more decided than in the case of hand-puddling. As regards the increased yield, this is merely what we have a right to expect if we consider the puddling process to consist in the oxidation of the carbon and silicon of the pig by the oxygen of the oxide of iron. That this result is attained, nearly to the extent that the theory requires, in Danks's puddler, and has never been more than partially attained by the most careful experiments in hand-puddling, points clearly to the fact that the contact of the molten pig-iron with the oxide of iron is much more intimate and complete in the one instance than in the other. The action of puddling in Danks's machine may be considered to be twofold first, the removal of the carbon, silicon, and phosphorus of the pig, which is the primary object, and, second, the production of wrought iron direct from the ore, which is entirely an incidental result. Intelligent metallurgists were not long in recognizing in this latter result a fact of deeper import and greater value than the attainment of a perfect puddling process. A new method

Jan 1, 1874

By John I. Yellott

SINCE the days of Newcomen and Watt, when men first sought to turn the energy of fuels to useful purposes, coal-generated steam has supplied most of the power needed for both stationary and mobile applications. The low efficiency and large water requirements of the nineteenth century steam-power plant caused many engineers to turn their thoughts toward more direct means of converting heat into power. As far back as 1791, John Barber secured an English patent on a combination' which he might well have called a "gas turbine." He proposed to generate procducer gas from coal or charcoal, to burn it under pressure in air obtained from a reciprocating compressor, and to drive a turbine wheel with the resultant hot combustion products. With the optimism characteristic of the inventor, he hoped that the turbine would not only operate his compressor but also perform useful work. There is no record that Barber ever built his machine, but if he had done so he would have learned that useful power can result from such a combination only when both turbine and compressor are highly efficient and when the temperature of the gas entering the turbine is not far below 1000°F. Hot-air prime movers continued to attract attention, and both Stirling in England and Ericsson in America2 built reciprocating engines that operated with some success upon coal-heated air. The internal-combustion engine, burning liquid fuels, supplanted the hot-air type, and, for the first time, challenged the supremacy of both the steam cycle and its familiar fuel, coal. LIQUID FUELS COMPETE WITH COAL As the increasing use of the automobile multiplied the demand for gasoline, the supply of residual fuel increased rapidly, and heavy oil declined in price to the point where it became competitive with coal. First in the marine field and later in stationary plants in areas adjacent to refineries, oil began to be widely used. Oil's greater convenience and higher heating value per pound of weight or per cubic foot of bunker space have caused it to take over much of the marine field. The introduction of the highly efficient diesel engine, capable of burning a fuel that is cheaper than gasoline, again threatened the position of coal, for the operating costs of the diesel became directly competitive with those of coal- burning equipment. In isolated power plants and smaller marine installations, the diesel provided the medium by which oil again successfully invaded fields formerly dominated by coal. The diesel engine, provided with an

Jan 1, 1946

Gentlemen.-It is pleasant to be able to report that the year just closed has been a prosperous and successful one for the Institute. As is shown by the reports of the Treasurer and the Finance Committee, the business affairs of this organization are in excellent condition. With property valued at more than three-quarters of a million dollars, and with considerable sums in various funds and endowments, it is possible to spend on each member of whatever class $22.65 each year, more than the maxi- mum amount of dues received from any one, and substantially twice the average amount, $10.94, received from all. To do this has required close management and a strict regard for our limitations. In 1926, when the Budget was made up, the estimated expenditures for the work which it was felt the Institute must do exceeded the estimated receipts by some $14,000. At the close of the year, despite a number of unexpected decreases in receipts, it had proved possible to accomplish substantially all the work laid out and close the books with the usual transfer of initiation fees to the General Reserve, and still only reduce the cash balance $2,074.54. This was made possible by the hearty and loyal cooperation of the whole staff of employees and the extremely large amount of gratuitous service rendered by the officers, the members of the Divisions and technical Committees, and the membership generally. Even so it was impossible, because of limitations of funds, to undertake many things it is highly desirable for the Institute to do, and it was necessary to refuse the publication of important papers and committee studies, because of the lack of funds. PUBLICATIONS In an analysis of the income and expenses of the Institute published in the February issue of our Journal, MINING AND METALLURGY, it was pointed out that the largest item of expenditure is, as it should -be, for publications. Printing, binding, and distributing the various technical papers sent to the members cost in 1926 more than all the money received from dues, including the portion allocated as subscription to the magazine. Within the. year, the following volumes were printed and, with the exception of the second volume of TRANSACTIONS, which was mailed in January, were distributed : TRANSACTIONS, Volume 73, 1241 pages, covering papers on non-ferrous metallurgy, milling and concentration, non-metallic minerals, iron and steel, and the Institute of Metals Division papers read at the

Jan 1, 1928

By F. Brons, W. C. Miller

Pressure information for use in material-balance calculations is obtained, where possible, from pressure build-up surveys in shut-in wells. Using proper extrapolation methods, static pressures are obtained which, by averaging, give the field static pressure. Often, particularly in fields with a large number of wells, only spot pressure readings are available. A graphical method is presented here which enables the determination of the corrections which must be applied to the spot readings to give an estinzate of the static pressure. Although the static pressures thus obtained are not so reliable as those from build-up surveys, they are more nearly correct than the spot readings themselves for use in material-balance calculations. INTRODUCTION The average static pressure in a bounded reservoir is determined from a number of individual-well pressure measurements. Where pressure build-up curves are available, extrapolation methods such as described in Ref. 3 may be used to determine the static pressure in the drainage area of each individual well. The possibility of using pressure build-up curves presupposes that each well being surveyed is closed in during a certain period and that, during this time, a pressure recorder is left suspended in the hole. For surveys in fields with a large number of wells, this is usually not feasible for economic and other reasons. Either a large number of pressure recorders would have to be used simultaneously or, using a limited number of recorders, the time interval needed to complete a field-wide survey would be too long. The data obtained for this incomplete coverage are insufficient to permit reliable averaging of the few calculated static pressures over the entire reservoir. In many such cases another type of pressure information is available, i.e., spot pressure readings. During this type of pressure survey all wells are closed-in simultaneously and, after a reasonable shut-in time (e.g., three days), pressure readings are taken by running the recorder in and out of each successive well. These surveys, which are less expensive, are often taken at regular intervals, say once or twice a year. In fact, such surveys are required by the state regulatory bodies in many portions of the united States. These spot readings are normally lower than the static (fully built-up) pressure due to the relatively short shut-in time. No direct means of extrapolating such a reading to the static pressure is available because no pressure build-up record is obtainable. Consequently, these data are inferior to pressure build-up information as a basis for estimating the stabilized reservoir pressure in the drainage area of a specific well. For the common case where abundant spot readings but only a few pressure build-up surveys are available, our studies suggest that it may be possible to design a program which will combine the two types of information and provide an estimate of the average reservoir pressure that is more reliable than that obtainable solely from either set of data. in time) gives a point marked p. The actual static pressure at the time the well was shut-in is marked by p.. The illustration shows that, even if a build-up curve is available and can be extrapolated, a correction

By Ben Gumpertz

The important factors in any study of the screening of sand with a gravel envelope, as applied to use in oil wells, are: (I) sand size and shape, (z) gravel size and shape, (3) ratio of gravel size to sand size, (4) flow velocity, (5) viscosity of the fluid. Perhaps the first extensive investigation of the function of gravel in screening sand was performed by Coberly and Wagner,' from which the following conclusion was drawn: "The diameter of the largest grains in a single classified sand suitable for gravel packing is approximately 13 times the grain size at the ten-percentile analysis of the formation sample." ?;his applies to sands classified by Tyler screens and is for gravel grains of the maximum size that could be used to form a stable bridge. Field practice has shown that the screening effect of a given gravel for a given sand apparently varies with the flow velocity." Also, it has been assumed by some operators that the thickness of the walls of the gravel envelope surrounding the well has little effect upon the screening process. It is thought by others that a narrow envelope of gravel might form an ineffective screen. Thus the purposes of this work are: 1. To investigate the effect of gravel-sand size ratio upon screening action under the condition of varying flow velocities. 2. To investigate the effect upon screening action of varying the thickness of the gravel screen. 3. To investigate sand migration in the gravel screen and the effect of flow velocity and gravel size upon sand migration. Description of Apparatus In an attempt to reproduce field conditions for the purposes of this investigation, a flow tube was constructed, according to the manner of Urenj3 to represent a radial drainage segment of an oil sand. To arrive at the dimensions of the flow tube, a radial drainage segment of rectangular cross section was assumed to define an area of z sq. in. on the face of a well 6 in. in diameter. From this the dimensions of the segment were calculated out to a distance of 5 ft. from the face of the well. By computing cross-sectional areas at a number of sections along the rectangular segment and transforming these areas into the circular form, a drainage cone was obtained having everywhere the same cross-sectional area as the drainage element of rectangular cross section. To construct the apparatus, two sections of pipe of 7%-in. inside diameter, one 13 in. and the other 4 ft. long, were joined by a bolted flange. A mandrel having the dimensions of the drainage cone was centered in the pipe and a neat cement mixture was cast around it. A protective gasket was placed between the two sections of pipe so that the cement body could be separated at that point. When the mandrel was withdrawn a drainage cone was obtained (Fig. I).

Jan 1, 1941

By Ben Gumpertz

The important factors in any study of the screening of sand with a gravel envelope, as applied to use in oil wells, are: (I) sand size and shape, (z) gravel size and shape, (3) ratio of gravel size to sand size, (4) flow velocity, (5) viscosity of the fluid. Perhaps the first extensive investigation of the function of gravel in screening sand was performed by Coberly and Wagner,' from which the following conclusion was drawn: "The diameter of the largest grains in a single classified sand suitable for gravel packing is approximately 13 times the grain size at the ten-percentile analysis of the formation sample." ?;his applies to sands classified by Tyler screens and is for gravel grains of the maximum size that could be used to form a stable bridge. Field practice has shown that the screening effect of a given gravel for a given sand apparently varies with the flow velocity." Also, it has been assumed by some operators that the thickness of the walls of the gravel envelope surrounding the well has little effect upon the screening process. It is thought by others that a narrow envelope of gravel might form an ineffective screen. Thus the purposes of this work are: 1. To investigate the effect of gravel-sand size ratio upon screening action under the condition of varying flow velocities. 2. To investigate the effect upon screening action of varying the thickness of the gravel screen. 3. To investigate sand migration in the gravel screen and the effect of flow velocity and gravel size upon sand migration. Description of Apparatus In an attempt to reproduce field conditions for the purposes of this investigation, a flow tube was constructed, according to the manner of Urenj3 to represent a radial drainage segment of an oil sand. To arrive at the dimensions of the flow tube, a radial drainage segment of rectangular cross section was assumed to define an area of z sq. in. on the face of a well 6 in. in diameter. From this the dimensions of the segment were calculated out to a distance of 5 ft. from the face of the well. By computing cross-sectional areas at a number of sections along the rectangular segment and transforming these areas into the circular form, a drainage cone was obtained having everywhere the same cross-sectional area as the drainage element of rectangular cross section. To construct the apparatus, two sections of pipe of 7%-in. inside diameter, one 13 in. and the other 4 ft. long, were joined by a bolted flange. A mandrel having the dimensions of the drainage cone was centered in the pipe and a neat cement mixture was cast around it. A protective gasket was placed between the two sections of pipe so that the cement body could be separated at that point. When the mandrel was withdrawn a drainage cone was obtained (Fig. I).

Jan 1, 1941

By Stephen G. Dardaganian

Pore volume compresibilitieu measured in the laborutory on core .samples are reported for typical reservoir .sarrrl.rtorres at reservoir pressure. These cornpressibilities ore different for each reseriloir sample and cannot be correlated to porosity. The compressihilities are a1so functions of presslire. In recent years several authors have pointed out the importance of including pore volume compressibility of the reservoir rock in certain reservoir engineering calculations. Hall' showed that in calculating the hydrocarbon volume of an undersaturated reservoir from the production per unit change in reservoir pressure, the neglect of rock compressibility could, in the extreme case of low porosity rock, lead to results in error by a factor of two. Hawkinsl' and Hobson and Mrosovsky showed that both rock and interstitial water compressibilities must be included to achieve satisfactory accuracy in this calculation. Although rock compressibility is an important reservoir property in these calculations, very few data are available. Hall' made compressibility measurements on a few samples in a small pressure range. No other direct pore volume compressibility measurements have been reported. Geertsma' discussed the elasticity of reservoir rock but did not present any new data. In this paper, rock compressibilities suitable for reservoir calculations are reported for a variety of sandstones typical of U. S. reservoirs. The measurements were made through a range of pressures which is also typical of reservoirs. EXPERIMENTAL PROCEDURE Plugs 1 in. in diameter and 2- to 3-in. long were diamond drilled, 14 from cores from seven oil-bearing or potentially oil-bearing sandstone, one from a quarried sandstone, and another from a shallow, oil-free, pure orthoquartzite. The plugs were extracted in toluene, vacuum dried, and then weighed. The plugs were then saturated with kerosene and reweighed. This gave pore volume. They were then again extracted in toluene. vacuum dried, and jacketed in 0.004-in. thick copper foil. A short length of -in high pressure tubing led from the jacket. The jacketed sample was then saturated with kerosene and placed in the hydraulic pressure cell as shown in Fig. 1. Movement of the mercury slug showed the change in pore volume of the sample under a given pressure change. Temperature was about 72" F for all measurements. Before taking any measurements, the external pressure on the sample was raised to 10,000 psig and kept there for several hours. This formed the thin copper jacket around the plug. 7-he pressure was then removed and the sample left at least overnight, during which time it recovered its original pore volume. An external pressure of 12,000 psig was then applied and held constant. The change in pore volume was noted as the internal pressure was raised in 1,000 psig increments to 10,000 psig. The internal pressure was then reduced to zero, again noting pore volume changes,

By Foster Fraas

INTRODUCTION THAT variations in the humidity of the air and in the moisture content of a mixture of broken solids being separated electrostatically cause trouble is not new.1 Much of the reputation for unreliability commonly ascribed to the electrostatic separation processes is probably due to this one factor alone. Some operators dry thoroughly before separating; and while this is good in many instances, there are others in which it is not the remedy for trouble. Some mixtures behave best in very dry air and with the mixtures fed to the separator while hot to reduce the adsorbed water content. On the other hand, an overdried mixture on coming to equilibrium with more humid air, has been known to take up moisture selectively on one family of particles, as of coal in the presence of slate and clay, and give sharper electrostatic separation. From these observations it is concluded that there is a permissible moisture content for a particle and also for the atmosphere surrounding it, if in equilibrium, at which the particle will have a conductivity or contact potential2-4 that is ideal for electrostatic separation. This permissible moisture content varies between a wide range of limits for the different materials that are separated and with the kind of electrostatic separating process used. Water can be present as a result of adsorption and condensation from the atmosphere, as an accumulation before or during mining, or as a residue from a previous process step. The water may exist as a liquid film or as an adsorbed layer of vapor. If the water exceeds permissible limits it must be removed. Its state determines the method. Drying by evaporation is necessary for adsorbed water, for part of the liquid-film water (that is, up to several percent of the dry weight), and for free water in the internal structure. Large water contents may be removed by drainage or filtration. At just what point mechanical removal should cease and drying by evaporation begin depends upon the method of mechanical removal and its cost. Particles can also be separated according to their differences in dielectric constant when suspended in a liquid of intermediate dielectric constant. Recovery of this liquid presents a similar problem. PERMISSIBLE MOISTURE The adsorbed moisture on the outer surface of minerals can be quickly removed or replaced. Accordingly, in speaking of adsorbed moisture contents, either that of the solid or that of the surrounding air may be considered, the two values being connected by a distribution coefficient which varies with the temperature. However, such a condition does not necessarily exist in processes where an initially dry material is suddenly introduced into an atmosphere having a partial pressure of water vapor or where a moist material is suddenly introduced into a dry atmosphere. Here the resultant differences in the

Jan 1, 1947

The Palabora ore consists of two types, a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. The latter type also contains substantial quantities of phosphate. These two ore types are separately crushed and are kept separate through copper flotation and magnetic separation, for recovery of magnetite, with the low Ti magnetite being shipped as iron ore. High phosphate tailings are pumped to Foskor, a government-owned phosphate plant nearby. The Palabora plant was originally designed in 1966 for 33, 000 tpd using two 54 in. by 74 in. Allis -Chalmers gyratories; two 7 ft (2. 13 m) standards; four 7 ft shortheads; and six grinding lines, each using one 1,200 hp rod mill and two 1,200 hp ball mills. A fifth short- head and one more grinding line were added later; and with flowsheet improvements, the capacity of the plant was increased to 59, 500 stpd. A further plant expansion involving a third 54 in. primary and two 32 ft by 15 ft (9.75 by 4.6 m) 9,000 hp autogenous mills and another flotation section will bring its capacity to 87,500 stpd in 1977. These two fully autogenous mills are constructed entirely out of doors near the primary crusher, and the ground ore will be pumped a mile to the concentrator by a five-stage pumping system. The Palabora ore is mined with 6, 10, and 12 7d (4.6, 7.6, and 9. 2 cu m) shovels and hauled to the crushers in 110 and 165 st trucks. Sixty-five ton trucks were originally used, but the crusher dump pockets were designed for larger units. Dump pockets, crushers, feeders, and take- away belts are offset in order to keep the two ore types separate. Centerlines of the crushers are only 43 ft (13. 1 m) apart; but, because of their being offset, maintenance room is ample. Initially, more carbonatite ore than foskorite was mined; but as the pit has deepened, this ratio has been reversed. The Palabora ore breaks in the pit with a large amount of oversize boulders; and, with the use of larger trucks, a splitter has been installed on one side of each dump pocket to protect the crusher spider. Smaller trucks dump on the opposite side. To accomodate the splitter, the pocket edge has been raised one meter and moved back one meter. Dust is collected through a special vent shaft between the crushers and the mantle relining area; but even so, two high-pressure water spray headers with nozzles are installed under the edge of the pocket at each dumping position. While only one truck dumps at a time, sprays from all four headers are used to suppress dust. Any leakage of water through the seal around the upper bowl of the crusher is caught by a circular trough under the seal and directed to a sump pump. At this point, there

Jan 1, 1978

By Warren B. Weeks

The development of the relatively deeper fields discovered during 1937 helped build the 1938 production to 18,456,760 bbl., an increase of 6,295,910 bbl., or 51.6 per cent over 1937, and the largest production for south Arkansas since 1930. Schuler and Rodessa accounted for the increased production as well as for over half of the wells drilled in the state. There were 243 holes drilled during 1938, of which 200 were completed as oil or gas wells. Of the 29 wildcat wells completed, 25 were dry, 3 found oil in the Smack-over limestone, while 1 made a small oil well in the Nacatoch sand. This was less than half the number of wildcats drilled the previous year, but nearly twice as many field wells were drilled. The old depth record of 7973 ft. was exceeded twice during the year, with the present record of 8332 feet. Trend of Prospecting The porous "Reynolds" oolite of the Smackover limestone1 has been the object of most of the wildcat prospecting during the past two years. Seismograph work, which brought 22 crews into this area during 1938, was largely pointed toward a study of the structure of this limestone formation. Thirteen dry wildcats have been drilled to this formation and five pools have been opened in it since it was first found to be productive at Snow Hill in the spring of 1936. With the failure of "updip" prospects to produce, activity moved southward and basinward. Success in five instances in Columbia and south Union Counties has spurred activity in this area. Much of the acreage is under lease and half a dozen deep limestone tests are assured for the current year. Fig. 1 shows the location of the principal oil fields in south Arkansas, as well as one or two minor producing areas. The fields are numbered in the order of their discovery. It is shown that most of the recent discoveries are from the deeper formations. Dry wildcats that penetrated

Jan 1, 1939

By Warren B. Weeks

The development of the relatively deeper fields discovered during 1937 helped build the 1938 production to 18,456,760 bbl., an increase of 6,295,910 bbl., or 51.6 per cent over 1937, and the largest production for south Arkansas since 1930. Schuler and Rodessa accounted for the increased production as well as for over half of the wells drilled in the state. There were 243 holes drilled during 1938, of which 200 were completed as oil or gas wells. Of the 29 wildcat wells completed, 25 were dry, 3 found oil in the Smack-over limestone, while 1 made a small oil well in the Nacatoch sand. This was less than half the number of wildcats drilled the previous year, but nearly twice as many field wells were drilled. The old depth record of 7973 ft. was exceeded twice during the year, with the present record of 8332 feet. Trend of Prospecting The porous "Reynolds" oolite of the Smackover limestone1 has been the object of most of the wildcat prospecting during the past two years. Seismograph work, which brought 22 crews into this area during 1938, was largely pointed toward a study of the structure of this limestone formation. Thirteen dry wildcats have been drilled to this formation and five pools have been opened in it since it was first found to be productive at Snow Hill in the spring of 1936. With the failure of "updip" prospects to produce, activity moved southward and basinward. Success in five instances in Columbia and south Union Counties has spurred activity in this area. Much of the acreage is under lease and half a dozen deep limestone tests are assured for the current year. Fig. 1 shows the location of the principal oil fields in south Arkansas, as well as one or two minor producing areas. The fields are numbered in the order of their discovery. It is shown that most of the recent discoveries are from the deeper formations. Dry wildcats that penetrated

Jan 1, 1939

By Augustus Locke

MY conclusions apply to the engineer in California ore hunting; and, because the product has been overwhelmingly gold, that means gold-ore hunting. But, I wish to think of ore hunting, not as employment for engineers, but as engineering. I wish, moreover, to think of it as productive of ore in significant quantity. The small mine, even if good, means little. Only new districts, or large extensions of old districts can engage our attention here. The conclusions are summarized as follows: (1) The bright color of California mining history comes from the suddenness and intensity of its outburst of gold. Had the mining been averaged from the start, it would soon have become dimmed among greater industries. For fifty years, California has proceeded as an agricultural, timber and oil, but not a mining region. 1

Jan 1, 1931

By C. E. Schwab

A lead-zinc orebody, in fairly strong quartzite and with a dip of 35" to 60°, is block-caved by use of scrams in a stair-step pattern up the ore footwall. Scram linings to handle coarse muck and permit the use of folding scrapers are developed by the use of end-grain wooden blocks to reduce maintenance and keep operating cost to a minimum. THE Bunker Hill mine, since its discovery in 1885, has steadily produced a high grade of lead-silver-zinc ore. By the end of 1952 over 21,000,000 tons of this high-grade ore had been produced by square-set mining, and reserves in the mine continue to be very satisfactory both as to quantity and grade. For many years prior to 1941, mine production and mill capacity had been 1200 tons of feed per day. Closely adjacent to the mill, and stored behind dikes, coarse jig tailings had been impounded during the time preceding the advent of fine grinding and selective flotation. When manpower became short in 1941 and sink-and-float preconcentration was proved successful, mill capacity was increased to 1800 tons per day to treat these jig tailings economically. By 1946, because the supply of jig tailings was limited, underground exploration was started to discover and prove ore reserves of low-grade material which could be mined by an appropriate bulk mining method. During the years of square-set mining many possible areas of low-grade mineralization had been observed. One chosen for the first exploration work was sufficiently remote from active mining areas so that subsidence, if an ore-body were proved, would cause no problem. Also, old adits and workings were still open and in good enough condition so that exploration in the mineralized zone could be started with a minimum of preparatory work. In 1948 an orebody was proved of sufficient tonnage, of a grade about 2 pct Zn, 0.5 oz Ag, and 1.0 pct Pb. It was decided to use block-caving, the only appropriate mining method by which this grade of ore could be economically recovered. Exploration for additional reserves in other areas of the mine is continuing, but ultimate results are not known at this time. With more sink-and-float capacity, larger ball mills, and more flotation machines, mill capacity was increased to 3000 tons per day, permitting the mining of ore in the square-set area at a maximum rate not usually achieved, because of the scarcity of labor. Increased mill capacity also permits block caving and the mining of jig tailings at variable rates to keep mill feed up to 3000 tons per day. Fortunately the three types of feed are amenable to the same mill circuit and reagents for recovery of Pb and Zn. For example, during the first 10 months of 1952 square sets produced 827 tons per day, block-caving 1421 tons per day, and jig tailings 643 tons per day, an average daily production of 2891 tons for all three products. Exploration had proved the existence of an ore-body 1000 ft long and 165 ft wide in horizontal section, see Fig. 1. Company engineers were concerned only with the vertical extension, about 300 ft, from an old level to the surface. Much of this almost outcropped, Fig. 2. The ore lies in the hanging wall of a major fault of the Bunker Hill mine, standing at 65" in one end of the zone and separated from the fault by a wedge of waste, see Fig. 3. This wedge pinches out near the center of the zone, at which point the ore dips 45", lying nearly on the fault, Fig. 4. The remaining portion lies on the fault and conforms to the fault dip of 35", Fig. 5. Open-pit mining for the top of the ore was considered, but since the ore zone dipped into and under the mountains, adverse waste-to-ore ratios precluded use of this method. The ore occurs in massive quartzite of sufficient strength to support untimbered drifts, crosscuts, and raises. Zones of weakness in the quartzite are bedding, jointing, and small faults or slips. The mineralization, which occurs as small stringers of sphalerite and galena as well as pyrite, creates another line of weakness. The mineral veins or veinlets in themselves are high-grade. Their size and regularity and the amount of barren quartzite by which they are separated determined the limits of mineable ore, which are all assay limits except for the one determined by the major fault. Block 1 Without any background of caving in this type of quartzite, engineers selected the first block on the very steep end of the zone. Compelling reasons prompted this decision. The steep portion of the ore in Block 1 was of the lowest grade, so that if difficulties were encountered no very valuable ore would be lost, while the experience gained might be applied in mining the remaining blocks. A block 200x200 ft was laid out, with four scrams spaced 50 ft apart for drawing and placed at a right angle to the strike. Finger raises were placed in a 25-ft interval grid pattern, with flat undercutting done by crosscuts at the undercut level 25 ft above

Jan 1, 1954

By Earl Chairman Oliver

The major development in stabilization of the oil industry during 1933 was the transition in the United States from state control to federal control in many of the functions that government is presumed to exercise. A brief review of the influences leading to that transition is given here to suggest its significance and to assist in forecasting its further development. Bitumens were known to the ancients and have been applied to minor uses since earliest historic times, but it was not until after the discovery of oil in considerable quantities near Titusville, Pennsylvania, in 1859 that it was made the basis of extensive commercial undertakings. In 1859 little was known about the origin of oil and gas, the nature of these deposits, and the physical laws that controlled their accumulation. Scientists soon began to study them, but 50 years or more of active oil-field development had elapsed before sufficient geological information had been accumulated to point the way toward efficient recovery of these products. In fact, only within the past five years has the function of reservoir energy become widely understood, yet it is a primary factor in oil recovery. discovery near Titusville, this infant industry has developed into an industrial giant. In complete ignorance of their destructive effect, wasteful development methods were initiated in Oil Creek and these became industrial habits. These habits in turn became oil and gas law. Under that law vast sums of money have been expended, rights have become vested and development methods fastened on a great industry that not only bring upon it periodic demoralization but cause ruthless destruction of the nation's reserves of these important natural resources. This is occurring in the midst of a petroleum era when oil is essential to the nation's security, its industrial supremacy, and the personal convenience of every citizen. Its conservation, therefore, has become a question of grave national concern. Conflict between PHysical Facts and Oil Law This destruction of an important natural resource and periodic demoralization of a vast industry can be halted only by readjusting oil

Jan 1, 1934

By Arthur Notman

DESPITE the tremendous drop in the volume of domestic production of metals, their prices, and profits, the world as a whole has managed to produce and consume nearly as much as in 1937. Measured by production, 1937 was the record year for copper, lead, and zinc. The Copper Institute figures for 1938 (estimating December as equal to November) show that although apparent domestic consumption declined 309,422 tons, foreign consumption increased 133.035 tons. The total for 1938 was 1,971,790 tons compared with 2,148,177 tons for 1937. The domestic decline was 38.5 per cent, the foreign increase 9.9 per cent, and the total decline 8.2 per cent.

Jan 1, 1939

By E. A. Stephenson

In spite of tremendous handicaps notable advances in production engineering have been achieved during 1932. The technique of deep well drilling has continued to progress, notably in California and at Big Lake, Texas. In the latter field a method has been devised by which two grades of oil in contact with each other are produced without intermingling. In rig design many improvements have been made whose objective is to facilitate deep drilling with reduced power losses and increased life of the equipment. Flush joint casing and drill pipe have been improved further, careful tests indicating that the drilling time can be reduced by from 5 to 20 per cent where flush-joint pipe is used. Slow-speed pumping has come into wider use, with further increases in over-all efficiencies. A number of improved well pumps also have been developed and are being tested. One of the most important of these is a positive displacement pump of the rotary type, directly connected to an electric motor placed in the bottom of the hole, and adaptable to various sizes of tubing and casing. In some localities the trend is towards the replacement of electric motors and large-cylinder engines by multiple-cylinder gas engines. Experiments have been conducted and critical analyses made of flow conditions in wells equipped with various styles of tubing which give promise that tubing may be designed to fit individual well conditions. In those wells producing at less than maximum capacity, the gas-oil ratio has been shown to depend on the rate rather than on the method of production, or the design of equipment. Important factors in the design of screened pipe have been carefully analyzed and made the basis of a method for determining the required mesh. Remarkable progress has been made in the use of subsurface pressure data. In East Texas particularly, use of such data is providing a means for the control and equalization of water encroachment and is also pointing the way to a sound means of allocating to individual tracts an

Jan 1, 1933

By F. Z. Schellenberg

(Pittsburg Meeting, March, 1910.) SYSTEMATIC exploitation in the Pittsburg coal-seam on a large scale is simple where the boundaries of the property do not interfere by forcing drainage-, ventilation-, and transport-lines of entries to be run to particular confined fronts. A prime condition governing development is the natural direction of the seam's perpendicular cleavage-planes, giving long lines of smooth faces near together and parallel, bearing about 65° to the left of the meridian and therefore crossing the basins. The gradients of dip into the basins change from 10 per cent at the east rim to practical flatness northwestward across the great coal-fields, a hundred miles wide; the clip being halved in rate at each successive crossing-over of an anticlinal crest. Elevations above sea-level on this transverse section, in scope of present development, differ by 1,000 ft. between low trough and high outcrop. Local irregularities of dip are found, but the main feature to be recognized is the pitch of the basins-the general rise northeastward at 20 ft. per mile, from 100 ft, below sea-level at the low point near the. SW. corner of Pennsylvania to 1,500 ft. and more above tide, and the appearance then, at the surface, of the lower coal-seams carried in the next deeper-lying thousand feet of rock-measures; below which series come the oil- and gas-sands of Oliphant's charted column of strata, reaching down altogether 3,000 ft. below the Pittsburg coal-seam. Because of -the general regularity of occurrence of the coal-seam, the mine-map depicting the courses of economic operation to be undertaken and the steps in controlled exhaustion, need be but a projection of two dimensions on the horizontal plane of space, and this for the most part composed of natural, almost unbroken lines, on the face and on the end of the coal, co-ordinating rectangularly.

Jul 1, 1910

By Morris Muskat

The detailed analogy between flow systems in porous media and the corresponding poten-tiometric model systems is developed under conditions where it may be desirable to take into account variable pay thickness, variable porosity, and permeability, and also the dependence of the fluid density on pressure. It is shown that in such models it is only necessary that the electrolyte thickness be made everywhere proportional to the millidarcy-feet of the formation. In contrast to the iso-vol type model, previously suggested as a basis for the analogy, the porosity does not enter directly in the construction of the model. It is introduced only in translating the electrical voltage gradient measurements into the equivalent fluid travel times. A discussion of this procedure is given. I NTRODUCTION It is now some 50 years since it was pointed out' that on the basis of Darcy's law Laplace's equation must govern the steady state flow of homogeneous fluids through porous media. It is 16 years since the obvious implication of this fact, namely, that such steady state homogeneous flow systems in porous media could be simulated by electrical analogies, was first applied2 to problems of practical interest with respect to oil production. In these initial studies major emphasis was placed on the use of electrolytic models, made of blotting paper, to give a direct and graphic history of the fluid particle motion in regular and infinite well networks. However, it was also noted there that the basic requirement of the model was that it give a potential distribution similar to the pressure distribution in the flow system, and that from the electrical measurement of the potential distribution the fluid particle motion could be graphically or numerically determined. This was demonstrated by application to the five-spot infinite network, for which a conducting metallic sheet was used to establish the equipotential contours. As anticipated, the fluid particle motion computed from these contours agreed well with that given directly by the blotting paper model. For irregular well distributions it was found more convenient to use electrolytic bath analogs rather than metallic sheets. Several investigations,3'4 as applied specifically to cycling well patterns, have been reported with these models, which have become known as "potentiometric models." However, the extremely laborious nature of both the electrical measurements by direct probing and the associated interprctive computations retarded the widespread use of these procedures. The electrical measurements can be accelerated by using a four-probe electrodc,5,6 which provides a means for simultaneously determining the streamline paths along which the fluid particles must move and the voltage gradients along these paths which are proportional to the fluid velocitics. With the increasing frequency of discovery of condensate pools, as drilling depths are becoming greater, the applicability of the potentiometric model to production problems, and especially to the study of well patterns for cycling, has been given a fresh impetus. Although the formal theory for determining the motion of fluid particles in porous

Jan 1, 1949