Search Documents

By H. M. Kraner, R. C. Devries, K. H. Gee, E. F. Osborn

On the basis of liquidus measurements in the system COO-Mg0-Al2O3-Sio, and previously published data, diagrams have been constructed at 5 pct Al2O3, intervals from 5 to 35 pct Al2O3,. Liquidus temperatures and primary phase fields are shown. The optimum composition of a blast furnace slag for a given alumina content is indicated. At the optimum point, ordinary slags will be entirely liquid and will have maximum desulphurization potential and minimum viscosity. The relation of optimum composition of slags to the "plateau region" of the liquidus surface, and the application of these data on synthetic quaternary slags to actual slag compositions are discussed. Index of refraction of glasses is given as well as composition, temperature, and phase data for each mixture. THE usual blast furnace slag, as a first approximation, can be considered a mixture of the four oxides, CaO, MgO, Also,, and SiO,. Systematic, extensive data for the quaternary system, CaO-MgO-A1,0,-SiO, is therefore required for the understanding of the properties of such a slag as a function of composition and temperature. With sufficient data, it should be possible to fix unequivocably the relative amounts of lime, magnesia, and silica required for a given alumina content to result in a slag composition having optimum properties. Other constituents, such as FeO, MnO, Ti02, and S, have an effect on the properties of a slag, but as long as they are present in small and approximately constant amounts they produce only a second-order effect superimposed upon the major changes in properties of slags determined by the relative amounts of the four major components. Viscosity and desulphurization data have been reported for mixtures approaching blast furnace slags in composition, but systematic liquidus data have not been obtained. Inasmuch as a slag must be all liquid in order to be most effective as well as practicable, clearly the temperature above which a mixture is all liquid (liquidus temperature) is a type of data needed. Such data have been obtained through the study of 446 compositions and are pre- sented in this paper along with a discussion of their bearing on the optimum composition of blast furnace slags. For an orderly presentation of the data, the quaternary system is viewed as a tetrahedron with one component at each apex. Fig. 1 shows a tetrahedron representing the system Ca0-Mg0-A1,0,-Si0,. The base is the ternary system Ca0-Mg0-SiO,, A1,0, is the top apex, and the front face, the system CaO-

Jan 1, 1955

In our sessions devoted to geophysical prospecting, the greater part of the time heretofore has been given to the presentation of theoretical subjects or highly technical details by specialists directly engaged in the development and perfection of the various methods. This was necessarily so, for we wanted such information available for the benefit of other workers and for our members who were anxious to gain a reliable understanding of the principles involved, to enable them to form an opinion of the adaptability of this new technique to their special problems. The methods have now been actively applied by many reliable organizations for several years and in this period there has been opportunity for operating mining men, engineers and geologists to appraise them. We therefore felt that it would be desirable at this meeting to give some time to interchange of opinion concerning results from actual cases. Consequently, the Committee on Geophysical Methods of Pros pecting sent out letters of inquiry to numerous mining people, asking for frank statements of opinion based on results from geophysical surveys at their properties. We have received many replies, among which 30 or more are of specific interest. On the whole, the point of view is remarkably uniform. Except for one or two who were, perhaps, a bit irritated, the operating men who have replied consider the methods to be capable of yielding valuable information when suitable conditions exist. Their attitude is definitely one of tolerance and of confidence in the integrity and sincerity of the outstanding workers. There is, however, a very general feeling that the chances of attaining positive and trustworthy results are small unless the work is directed by, or at least carried on with the close cooperation of, a geologist or mining man who is thoroughly familiar with the local geologic and mineralogic conditions and with the relations of the orebodies to rocks and structure. From certain comments, I am inclined to think that some operators are not greatly impressed with the cheapness of the work. Probably they are not attaching much weight to cost per acre, but are thinking primarily of total cost in terms of significant results obtained. It is

Jan 1, 1932

By Maurice E. Peloubet

This discussion of accounting will describe the statements and the information that the accounting system produces, from the point of view of those who use such systems rather than of those who prepare them and who do the detail and technical accounting work. In any well organized mine, quarry, or other enterprise exploiting a mineral deposit, no matter how small, some clerical and accounting work must be done. Miners and other employes must be paid, supplies must be purchased and issued, and various tax and information returns, which even the smallest enterprise must file, have to be prepared. In this chapter it is assumed that the enterprise has employes of this type and that they understand the fundamentals of record keeping and accounting. It would be impossible here to give sufficiently full explanations to enable a man with no previous clerical and accounting training to set up and operate an accounting and cost system for even the simplest extractive operation. Rather, we shall hope first, to tell the investor and the operator, from the chief engineer or president down to a subforeman, what to expect from the accounting statements and records and how to use this information in his daily work; and second, that it will enable the man with some knowledge of accounting or bookkeeping, but with little or no experience in any extractive industry, to set up and operate a satisfactory system for a mine or other extractive enterprise. For readers who wish to go further, the bibliography at the end of this chapter contains many references. The emphasis has, therefore, been placed on the statements to be produced and the purposes for which they are to be used rather than the underlying books and records. These are, with a few exceptions which will be described later, essentially what might be found in any industrial enterprise and would probably, in the extremely small enterprise, consist of handwritten journals, ledgers, analysis books, payroll books, and stores ledgers. In the larger enterprise, various types of mechanical accounting would be introduced in proportion to the complexity of the operation.

Jan 1, 1959

By C. F. Rust

Experimental evidence is presented showing that reproducible formation resistivity factor measurements and resistivity index determinations on reservoir core samples map be made utilizing either the two- or four-electrode methods. Equipment is described which permits the application of either technique to the core specimen without loss of time and with a minimum amount of effort. Since electrical resistivity measurements on reservoir rocks are important not only in electric log interpretations, but also in the study of fundamental rock parameters, it was considered desirable to compare the applicability of both techniques of resistivity measurement. INTRODUCTION The techniques employed in the measurement of electrical resistivity on reservoir rocks, as practiced in the petroleum industry, may be reduced to two fundamental methods: one utilizing two electrodes only, usually referred to as the two-electrode method; the other using two additional electrodes and commonly known as the four-electrode method. In the former, the core sample whose resistivity is to be measured is mounted between two electrodes, usually metal discs, which serve to pass a current of known magnitude through the saniple. The potential drop across the sample, measured between these same two electrodes, and the core dimensions furnish the necessary data to compute he resistivity of the sample. In the four-electrode technique the end plates, again usually ol metal, still serve as current electrodes. Additional probes or electrodes dispersed along the sample are utilized to measure the potential drop. Both methods are used in practice1,2 and it is the purpose of this paper to compare the two techniques as applied to the determination of formation reiistivity factors and the resistivity index exponent n, in Archie's empirical equation I = p/po = Sw 11. To evaluate the two techniques it is desirable to point out the experimental precautions which must be taken to insure reliable results. It is evident from the electrode arrangements of the two- and the four-electrode methods that, for a given sample, the volume of sample included by the four-electrode method is less than the volume included by the two-electrode method. One of the prime difficulties associated with the two-electrode method is the possible occurrence of an abnormally high resistance between the electrodes and the brine-saturated sample, which results in erroneous resistivity values for the core sample itself. Attempts to alleviate this difficulty meet varying degrees of success. Methods used in the past employ such absorbent materials as brine-saturated Kleenex: chamois, or felt. A technique described by Morgan, Wyllie, and Fulton,1 appears to be more satisfactory. Their method consists of spraying or painting the end areas of a core sample with conductive silver paint. This technique reduces contact resistances between the porous medium and the electrodes to a value which is generally negligible as compared to the resistance of the sample itself. In the four-electrode method these requirements are not as stringent since separate probes are used to measure the potential difference acrozs a portion of the sample. In this case, contact resistance occurring at the current electrode; are of no consequence. and those appearing at the potential

Jan 1, 1952

By L. W. Davies

A problem often encountered is the provision of materials which have impurity contents below a certain specified level. This problem is in some cases solved by making use of the segregation of the impurity with respect to the liquid and solid states of the material: an ingot of the material is subjected to directional solidification and the ends of the ingot. which are richer in solutes which respectively raise and lower the melting point of the solvent, are removed. An important extension of this process is the zone-refining process invented by pfann,' in which molten zones are passed successively along the length of an ingot and displace solutes towards the ends. Pfann's process is particularly appropriate in cases for which the segregation coefficient k does not differ greatly from unity, or when the impurity content must be kept extremely low (-=,6 atom fraction); it is widely used, particularly in the purification of materials for use in semiconductor electronic devices. It is the purpose of this paper to investigate theoretically the efficiency of the above refining processes; that is! we determine the most economic method of attaining a given yield of solvent of specified purity, taking into account the variables of the process. One variable of interest is the effective value of the segregation coefficient. which depends on the rate of movement of the liquid-solid interface and on the degree of stirring in the liquid; in addition to this, in the zone-refining process we are also interested in the choice of zone length for most efficient operation. A mathematical determination is made here of the lengths of successive molten zones which give, for an initially uniform distribution, the most efficient removal of a solute of arbitrary distribution coefficient. In order to be able to give a quantitative treatment of efficiency, we first define figures of merit applicable to a given distribution of solute. FIGURE OF MERIT Let an ingot of length L contain a distribution y(x) of solute: we confine our discussion to mono-tonic distributions, in order to avoid inconsistencies in the subsequent analysis. The first moments of the distribution about the origin and x = L are respectively L F = hy{x)dx [I] G = f(L -x)y(x)dx = YoL2-F, [21 where yoL is the total amount of solute present. We shall see that the quantities F and G are useful figures of merit for a discussion of the efficiency of zone-refining processes. In the first place, it is

Jan 1, 1960

By L. W. Davies

A problem often encountered is the provision of materials which have impurity contents below a certain specified level. This problem is in some cases solved by making use of the segregation of the impurity with respect to the liquid and solid states of the material: an ingot of the material is subjected to directional solidification and the ends of the ingot. which are richer in solutes which respectively raise and lower the melting point of the solvent, are removed. An important extension of this process is the zone-refining process invented by Pfann,' in which molten zones are passed successively along the length of an ingot and displace solutes towards the ends. Pfann's process is particularly appropriate in cases for which the segregation coefficient k does not differ greatly from unity, or when the impurity content must be kept extremely low (=10-6 atom fraction); it is widely used, particularly in the purification of materials for use in semiconductor electronic devices. It is the purpose of this paper to investigate theoretically the efficiency of the above refining processes; that is! we determine the most economic method of attaining a given yield of solvent of specified purity, taking into account the variables of the process. One variable of interest is the effective value of the segregation coefficient. which depends on the rate of movement of the liquid-solid interface and on the degree of stirring in the liquid; in addition to this, in the zone-refining process we are also interested in the choice of zone length for most efficient operation. A mathematical determination is made here of the lengths of successive molten zones which give, for an initially uniform distribution, the most efficient removal of a solute of arbitrary distribution coefficient. In order to be able to give a quantitative treatment of efficiency, we first define figures of merit applicable to a given distribution of solute. FIGURE OF MERIT Let an ingot of length L contain a distribution y(x) of solute: we confine our discussion to mono-tonic distributions, in order to avoid inconsistencies in the subsequent analysis. The first moments of the distribution about the origin and x = L are respectively L F = hy{x)dx [I] G = f(L -x)y(x)dx = YoL2-F, [21 where yoL is the total amount of solute present. We shall see that the quantities F and G are useful figures of merit for a discussion of the efficiency of zone-refining processes. In the first place, it is

Jan 1, 1960

By C. E. Mendenhall

THE word temperature has both a colloquial and a technical use. For everyday purposes of abusing the weather man, no very exact definition is necessary, but for the purpose of giving a simple summary of the physical laws that form the basis of practical pyrometry, something more precise is required. Beginning, therefore, with the common concept of "hotness" and "coldness," we must agree on a method of measuring differences in "hotness," on the unit to be used, and on the point from which measurements are to be taken. We shall then have a definite "scale of temperature," which can be used in all methods of pyrometry. But, as in many similar cases, it is much easier to define or describe something than it is to make practical application and use of the definition; so that much of our attention will be taken up with practical methods of realizing or applying the scale agreed upon. It was early observed that changes in temperature produced large and easily measurable changes in gases, which may be most simply separated into changes in volume (expansion and contraction) under conditions of constant pressure, and changes in pressure under conditions of constant volume. These changes are much the same in magnitude for the common gases oxygen, nitrogen, and hydrogen and also for the rarer helium and argon. This relative uniformity in behavior led to the suggestion of "the gas thermometer" and "the gas scale" as the basis for all temperature measurements. However, as methods were refined, differences appeared between different gases and different ways of using gases, so that Lord Kelvin introduced his more fundamental notion of the "absolute thermodynamic scale" of temperature, which he defined as follows: Given two bodies, say two tanks of water, at different temperatures to determine these temperatures on the "absolute thermodynamic," or Kelvin, scale, operate a thermal engine between these two temperatures, letting it take in heat from the hot body and give out heat to the cold, which therefore corresponds to the boiler and the condenser of a steam engine. The engine we may imagine as a cylinder and piston inclosing a gas and operating with the well-known Carnot or isothermal-

Jan 9, 1919

By C. M. Loeb, T. E. Norman

THE use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies of the factor sgoverning their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. THE DEVELOPMENT OF A SUITABLE WEAR TEST A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was. known that Ellis and his associates1.2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1948

By A. S. Yue, A. E. Vidoz, F. W. Crossman

Tensile specimens were prepared from a single grain of an epitaxially grown Al-CuAl2 eutectic ingot. The eutectic lanzellae were oriented parallel and perpendicular to the tensile axis of the specimens. Since the composite was of the eutectic composition, the aluminum-rich matrix could dissolve up lo 5. 7 wt pct Cu in solid solution and, therefore, was amenable to strengthening by precipitation hardening. The tensile properties of the eutectic single crystals were determined at room temperature as functions of interlamel-lar spacing, platelet orientation, and thermornechanical trealment. The obserced variations in composite stress and modulus with respect to the level of&apos; composite strain are discussed in terms of premature fracture of CuAlz platelets, a distribution function for the strength of the lamellae, and unequal strains due to localized fracture of&apos; platelets. The discontinuous fiber composite model of Kelly and Tyson is modgied to account for a changing distribution of fiber lengths during composite loading. The tensile properties at elevated temperatures were determined for the direc-tionally solidified eutectic oriented with platelets parallel to the tensile axis. The observed properties are attributed to the onset of plasticity of the CuAL2 phase above 150°C. DURING the investigation of whisker- and fiber-reinforced metallic matrix composites in recent years, two major problem areas have developed: 1) The fabrication of the composite involves tedious handling techniques in order to obtain a unidirection-ally aligned and uniformly spaced set of whiskers in the metal matrix. 2) Due to weak interfacial bond strengths or because of the formation of additional embrittling phases at the metal-fiber interface during long-time exposure or fabrication at elevated temperatures, many composite systems have exhibited considerably lower strengths than those predicted by a law of mixtures analysis.&apos; These problems have been bypassed by the technique of growing whiskers and plates of high-strength materials in a ductile metal matrix by controlled unidirectional eutectic solidification.2 The tensile properties of directionally solidified A1-CuA12 eutectic are presented here. This alloy consists of a ductile aluminum matrix, containing up to 5.7 wt pct Cu in solid solution, which is amenable to precipitation hardening by heat treatment and a reinforcing high modulus CuAlz intermetallic phase. The two phases are present in the form of alternating platelets or lamellae. The microstructural stability of this unidirectionally solidified alloy at elevated temperatures has been studied extensively.3.4 and preliminary tensile and bend tests have been reported. 5-7In the present investigation the tensile properties of the A1-CuA1, eutectic have been studied as a function of several ther-momechanical variables: solidification rate. heat treatment. rolling at elevated temperatures. and lamellar orientation. It was felt that the uniformity of structure and excellent interfacial bonding would give tensile properties concomitant with the metal matrix composite theory of strengthening proposed by Kelly and coson. 8-9 The tensile properties that were obtained point to a wide distribution of strengths for the CuAlZ platelets, which leads to large deviations from the predicted mechanical behavior for this composite. EXPERIMENTAL PROCEDURE Epitaxial Growth of Eutectic Alloy. The A1-CuA1, eutectic alloy was prepared by an epitaxial growth process. Sections of a master alloy ingot (total impurity content <0.008 pct) were placed in an alundum boat, melted. and directionally solidified to obtain a multigrained plate 12 by 2 by 4 in. This plate was tapered at one end to mate with a seed crystal 1; in. long and 4 by $ in. square. Then the seed-plate combination was placed in an alundum boat which sat in a quartz tube passing through the center of a horizontal resistance wound tube furnace. A dried argon atmosphere was maintained. The temperature gradient in the furnace was such that the liquid-solid interface of the eutectic alloy was located near the end of the furnace and could be observed through the quartz tube. Single-crystal plates were formed by melting the material back to the midpoint of the seed crystal of the desired platelet orientation and then epitaxially growing the plate from the seed by withdrawing the alundum boat from the furnace at a constant rate. This technique was used to produce aluminum and CuA12 lamellae parallel and perpendicular to the transverse direction on the plate. Metallographic examination showed that both phases were continuous across the original liquid-solid interface. It was also possible to grow a plate from two seeds placed side by side: and, although the lamellae of one seed were oriented at 90 deg to those of the second seed, the interface between the two grains remained parallel to the growth direction along the entire ingot length. Maintenance of a straight intergranular boundary during the solidification process was possible as long as both seeds were oriented with their original growth direction parallel to the solidification direction of the plate. Eutectic plates were directionally solidified at rates of 0.2, 1.0. and 4.7 cm per hr and sectioned transversely to the solidification direction to determine the apparent inter lamellar spacing of the lamellae. Metallographic examination was also employed

Jan 1, 1970

By J. B. Dorsey, T. W. Brinkley

Performance of a high-pressure, vaporizing gas-drive project in a volatile oil reservoir is discussed. The project has been in operation for over 8 years. Present recovery from the over-all displaced portion of the reservoir is 40 percent, and an ultimate recovery of 60 percent is indicated. Calculations reflect an over-all displacement volume of 50 percent for the entire reservoir; therefore, ultimate oil recovery will be 30 percent of the entire reservoir oil originally in place. Laboratory vaporization tests conducted prior to project initiation also are presented and discussed, along with an analytical method of determining stock-tank oil production and gar injection requirements related to over-all volumetric displacement efficiency from these data. Introduction The Shoats Creek field is located in Beauregard Parish, La., in the extreme western part of the state (Fig. 1). Discovered in 1956, the field is productive in three Cockfield sand zones, ranging in depth from 8,000 to 9.000 ft. The upper two zones, 1st and 2nd Cockfield, are condensate-bearing gas reservoirs. The lowest zone, the 5th Cockfield, is a volatile-oil reservoir. Laboratory work conducted on crude oil from the 5th Cockfield zone shortly after field discovery demonstrated that, when contacted with dry gas, signidcant volumes of the oil could be vaporized at reservoir temperature and at an appropriately high reservoir pressure. Further study led to the conclusion that early initiation of a crude vaporization project in the 5th Cockfield zone would be superior economically to other methods of reservoir depletion. Consequently, the zone was unitized and gas injection operations started late in 1958. This paper discusses laboratory work performed in conjunction with the project, and project performance to the present. History of Development The 5th Cockfield zone in Shoats Creek is composed of a thin, very shaly, low-permeability sandstone. Oil accumulation is controlled by a structural trap bounded by faults along the north and west and by a water contact on the southern boundary (Fig. 2). The zone covers a productive area of 1,550 acres at an average depth of 9,000 ft. The net sand section is thin, having a maximum thickness of 10 ft and an average thickness of 5.5 ft (Fig. 3). Average reservoir rock properties, as determined from core analysis are presented in Table 1. Shaliness of the zone is illustrated by the typical electric log of the 5th Cockfield section in Fig. 4. Because of the thinness and poor quality of the sand, the 5th Cockfield was developed on a wide spacing. Eleven completions were made in the zone between 1956 and 1961 for an average density of 140 productive acres per completion, with the majority of wells being dually completed in the 2nd and 5th Cockfield. Average initial potential for producers in the 5th Cockfield was 130 BOPD. Oil from the 5th Cockfield has a stock-tank gravity of 50.5" API; with a bubble-point pressure of 3,515 psia, the oil was highly undersaturated at the original reservoir pressure of 4,675 psia. Pertinent properties of the oil as determined in the laboratory are presented in Table 2. Because of the volatile nature of the crude, laboratory studies of its susceptibility to vaporization, as well as a vapor-liquid phase study, were conducted in addition to a standard PVT analysis. The vaporization study was conducted in a visual cell; a stepwise illustration of this work and laboratory measurements are presented in Fig. 5. Field

Jan 1, 1969

By F. C. Langenberg

It is the purpose of this paper to present a limited amount of experimental data obtained on the Charpy impact machine. Several concrete examples will be given showing the relation existing between the results obtained upon the Charpy impact machine and the behavior of the parts tested when in service. Although it is pointed out by G. Charpy and A. Cornu-Thenard1 that it is first necessary to determine a satisfactory working process before studying the correlation between the results of these tests and the behavior of the parts tested in service, this ideal course cannot be strictly adhered to. If a certain part repeatedly fails in service and the available tests give no indication of its cause, advantage must be taken of any possible means that will solve the problem; therefore, even though the reliability of the results obtained by the Charpy impact machine have been questioned by many, it was necessary to use this instrument without giving careful consideration to its possible sources of error. It would seem that the conclusions arrived at by Charpy -and Cornu-Thenard justify the assumption that the precision obtained by this machine is comparable to that obtained by the other more common forms of testing. The second general conclusion arrived at by them, namely, that the impact test upon notching does not offer any direct correlation to the ordinary tests, is also borne out by many hundred determinations made in the laboratories at Watertown Arsenal. This statement, however, should be qualified as follows: Other ordinary tests include the static tensile test from bars taken in a longitudinal direction and the Brinell hardness. The author agrees that no law is yet known for the computation of the energy absorbed in the rupture of bars of the same material but of different dimensions. Although Charpy and Cofnu-Thenard do not refer in their valuable article to the use of the Charpy machine in industrial practice, it should be stated that this instrument has been in constant use in the laboratory at Watertown Arsenal for several years, and is now employed for both routine and experimental testing.

Jan 1, 1920

By J. G. Tilton

While most of the Pittsburgh coal horizon is dependably regular, there are areas where it is dis-turbed by sandstone cutouts which can seriously hamper mining operations. Because these channel sandstones often cut out the coal abruptly, they are difficult to detect by core drilling; and mine operators, for want of a better way to discover them, have largely trusted to luck to avoid them. This paper, based on a study the author is presently conducting, is an attempt to point out some sources of information and signposts which might aid the operator in determining the presence of a cutout before he begins to mine. The presence of sandstone cutouts in the Pittsburgh coal has been known for many years. Some of these irregularities were observed at outcrops and others were discovered by drilling, but the majority were and are found during mining operations. These sandstone cutouts are commonly called "faults" and have been a bane to mining companies wherever they have been encountered. Profiles of some typical deposits appear in Fig. 1. The cutouts disrupt the normal system of mining, replace valuable coal reserves, create ventilation problems by emitting large quantities of gas and sometimes oil, limit the number of entries that can be economically driven, affect the quality of the coal, disrupt the normal structure of the coal, and create roof control problems. It might be expected that such severe disturbances in the structural regularity of the coal would instigate determined and extensive searches for possible cutouts prior to mining operations, but this apparently has not been so except in isolated cases. Two reasons may be cited to explain this lack of exploratory work. The first and probably the strongest reason is the over-all regularity of the Pittsburgh coal. No coal seam in the country exhibits the horizontal continuity and relative regularity of the Pittsburgh coal. It lies in an almost unbroken sheet across southwestern Pennsylvania, eastern Ohio and northern West Virginia, and has been recognized as far east as the Potomac Basin of western Maryland. Over 5729 square miles are underlain by this coal, of which 2077 square miles are in Pennsylvania, 2214 square miles in West Virginia, 1410 square miles in Ohio, and 28 square miles in Maryland. The area covered by this study is outlined by the map in Fig. 2. Over most of this territory the coal has the following characteristic structure as illustrated in Fig. 3: roof coal, draw slate, breast coal, parting, bearing in coal, parting, brick coal, parting, and bottom coal. With such regularity of thickness and structure, mines were opened and laid out with confidence that the coal would be present. Extensive drill testing was considered unwarranted and it was also quite expensive because the coal dipped to the west away from the Monongahela River. Consequently, drill holes were widely spaced and rarely encountered ad-

Jan 1, 1968

By L. G. Austin, R. R. Klimpel

This article demonstrates that the Gilvarry and Klimpel-Austin equations for the random fracture of solids are incorrect by deriving intuitively correct expressions for simple cases and showing that the foregoing equations do not reduce to right answers. It is the purpose of this article to point out serious errors in some existing treatments of the random fracture of solids. Gilvarry &apos; gives the equation where B(y,x) is the cumulative fraction by weight of particles which fall below size y when particles of size x are broken. The constants i, j, k contain shape factors and densities of flaws leading to propagating fracture surfaces. The authors believe this equation to be incorrect. Klimpel and usttin&apos; give where r~ is the number of fracture planes originating from edge flaws (per L where L is the edge length of the original particle), rs is the number of fracture planes originating from flaws on the particle surface (per S where S is the surface of the original particle) and rv is the number of fracture planes originating from flaws within the particle volume. This equation is also incorrect. The failures of these equations will be demonstrated by deriving intuitively correct expressions for simple cases and showing that the Eqs. 1 and 2 do not reduce to the correct answer. In this process, the flaws in statistical reasoning inherent in the derivations of Eqs. 1 and 2 become apparent. THE KLIMPEL-AUSTIN EQUATION Eq. 2 was derived by considering a set number of fracture planes occurring spatially at random within a given particle. This case will be treated here in its simplest form: a line with 1, 2, 3, etc., fractures occurring at random. This is illustrated in Fig. 1, with the original length of the line as Vo. The breakage of a long, thin, brittle fiber is a corresponding physical case, with the volume of a fragment proportional to its length. Assuming independence of the occurrence of the fractures, the probability of any one fracture occurring in length dV is dV/V0. The probability of the first fracture occurring at a length V to V + dV is dV/Vo. For the case of only one fracture per particle, formation of a number-size distribution of the left-

Jan 1, 1969

By Joseph E. Pogue

The past year in the petroleum industry was one of overproduction, rising inventories, low prices, and meagre to vanishing profits. This outcome was the result of a long period of intensive and uncompensated effort on the part of both financial and industrial interests, to stimulate supply on the theory that the primary problem facing the petroleum industry was the development of an adequate reserve of raw material to protect a large and ever-growing investment. The stimulus was applied in various forms and through diverse channels: capital had long flowed into the industry in excessive amounts under the attraction of large expected profits; the price level for crude petroleum had persistently been influenced by speculative considerations, with the result that prices declined slowly in periods of flush production and were quick to advance in anticipation of statistical improvement, thus maintaining a superfluous degree of stimulus on wildcatting and on drilling; speculation in inventories had led to the unsound, or at least unusual, business practice of accumulating huge stocks of oil; and, above all, the industry had directed the potent force of technology to the expansion of supply and achieved radical results in accelerating oil discovery, speeding up the rate of oil extraction, and enlarging the recovery of gasoline and lubricating oils from the raw material. In short, the economic conditions of 1927 were exactly those to which the objectively driven enterprise of the petroleum industry had long been directed; and the undesirable financial consequences arising therefrom reflected no lack of success in what had been set out to be achieved, but rather the failure to have established concurrently the necessary means of economic control to prevent the immediate conversion of reserves into current supply, and likewise the oversight in neglecting to apply the technological force to the enlargement and diversification of the market for petroleum products. Perhaps, when viewed in its longer perspective, 1927 will stand out as the turning point in the economic policy of the petroleum industry, when the technique of rationalizing production made its initial claim for recognition.

Jan 1, 1928

By Alphonse Hennin

It is well known that under certain conditions ammonia is found in the gas produced by the distillation of coal. Until recently it was held, and many still believe, that this ammonia exists in the coal, and is a natural product of the destructive distillation, varying in percentage, like the other products, according to the nature of the coal, but not formed synthetically beyond that limit. This opinion is in contradiction with well-established facts concerning the formation of ammonia from the elements of the coal. If any ammonia exists as such in the coal, the quantity is insignificant. The purpose of this paper is to explain the theory of the formation of ammonia during distillation, and call the attention of the members of the Institute to its application in connection with the production of heating-gas for metallurgical purposes, etc. For many years little or no importance was attached to the presence of ammonia in coal-gas. It was deemed by the gas-manufacturers an undesirable product of the process, as one of the impurities to be removed; and no attempt was made for its recovery. Not until its practical extraction and utilization was found possible, did scientists commence to investigate the question. Little was known about the nitrogen of the coal, and still less about the reactions leading to its transformation into ammonia. A. W. Hofmann, I believe, was the first to establish a relation between the percentage of nitrogen in the coal and the proportion of ammonia in the coal-gas. As early as 1863 he pointed out that, in dry distillation, such as is practiced in the manufacture of illuminating-gas, only one-third of the total nitrogen in the coal is liberated, two-thirds remaining in the coke. It is no longer possible to doubt that the ammonia is a synthetical product, resulting, under certain conditions, from the combination of the,elements of the coal. Chemistry teaches that ammonia is formed in many cases when

Jan 1, 1893

By E. Houdremont, H. Schrader, H. Bennek

The different influences exerted by the various alloying elements in iron and iron-carbon alloys give rise to a great number of complexities, which are difficult to grasp. It is important therefore to study any systematic relations that may exist between the effects exerted by the various alloying elements, in order to obtain a general classification and thus a clearer conception of the nature of alloy steels. A systematic survey of the alloys of iron, based on an investigation of the binary equilibrium diagrams, was recently published by Wever. Although his work deals little with properties of importance in works practice, its purpose being rather to point out the theoretical agreement among the types of binary equilibrium diagrams and the position of the alloying elements in the periodic system (atomic radii, etc.), the classification proposed nevertheless also suggests relationships among the properties of the alloys in question, even though the alloys may contain carbon in addition to iron and the alloying element. Wever divided the alloys of iron into one group exhibiting an open or enlarged gamma field and another exhibiting a closed or restricted gamma field, with both groups capable of further subdivision depending upon whether a continuous series of solid solutions is formed, or, owing to the separation of compounds, etc., only a limited series. Thus all alloying elements which with iron form a closed gamma field, a "gamma loop," produce alloys that beyond the composition corresponding to the greatest extent of the gamma loop are composed of ferrite alone at all temperatures. Alloys of this composition accordingly are not susceptible to ordinary heat treatment because of the lack of transformations. Steels of this class may thus be divided into steels that contain less than the critical amount of alloying element, and are subject to heat treatment, and those that contain more than the critical amount of alloying element and are not subject to heat treatment. Thus chro-

Jan 1, 1935

By H. Schrader, E. Houdremont, H. Bennek

The different influences exerted by the various alloying elements in iron and iron-carbon alloys give rise to a great number of complexities, which are difficult to grasp. It is important therefore to study any systematic relations that may exist between the effects exerted by the various alloying elements, in order to obtain a general classification and thus a clearer conception of the nature of alloy steels. A systematic survey of the alloys of iron, based on an investigation of the binary equilibrium diagrams, was recently published by Wever. Although his work deals little with properties of importance in works practice, its purpose being rather to point out the theoretical agreement among the types of binary equilibrium diagrams and the position of the alloying elements in the periodic system (atomic radii, etc.), the classification proposed nevertheless also suggests relationships among the properties of the alloys in question, even though the alloys may contain carbon in addition to iron and the alloying element. Wever divided the alloys of iron into one group exhibiting an open or enlarged gamma field and another exhibiting a closed or restricted gamma field, with both groups capable of further subdivision depending upon whether a continuous series of solid solutions is formed, or, owing to the separation of compounds, etc., only a limited series. Thus all alloying elements which with iron form a closed gamma field, a "gamma loop," produce alloys that beyond the composition corresponding to the greatest extent of the gamma loop are composed of ferrite alone at all temperatures. Alloys of this composition accordingly are not susceptible to ordinary heat treatment because of the lack of transformations. Steels of this class may thus be divided into steels that contain less than the critical amount of alloying element, and are subject to heat treatment, and those that contain more than the critical amount of alloying element and are not subject to heat treatment. Thus chro-

Jan 1, 1935

By W. T. Cardwell

This paper presents a theory for estimating the rate of gravity drainage of a liquid out of a sand column. Account is taken of the variation in permeability to the liquid as the saturation in the upper part of the sand becomes less than 100 pct. The theory is confirmed by previously published experimental data. Introduction Petroleum engineers have expressed the need for 4 theory of gravity drainage. Brunner,&apos; in particular, has pointed out that some type of mathematical theory is necessary to begin the application of laboratory data to field problems. Muskat and his associates2&apos;3-4 have recently made contributions to the theory of gas-drive behavior and have indicated an intention to apply their methods to water-drive systems. No theory of gravity drainage rates has been developed, however, and it seems desirable to formulate one at this time. Differential Equations of Capillary Flow The flow of liquids in partially saturated porous media has been studied by many investigators.6-10 Richards6 presented derivations of fundamental differential equa- tions governing two-phase capillary flow; and used simplified forms of those equations in solving a steady-state problem. Muskat and Meres6 presented and used equations different from those of Richards. Their equations did not explicitly involve capillary pressure gradients; but included, on the other hand, terms expressing the effects of the evolution of gas from the liquid phase during flow. Leverett8 stated in 1940 that "previous work on the flow of fluid mixtures in porous solids [had] failed adequately to account for all of the three influences that cause motion of the fluids: capillarity, gravity, and impressed external pressure differentials." Leverett&apos;s basic equations, however, were specialized forms of the general equations of Richards,5 which had actually taken account of the three influences mentioned by Leverett, but had not been used in a problem involving all three. The fact is that our knowledge of capillary flow and our ability to express this knowledge in differential equations exceed our ability to solve the equations except in a few cases. General differential equations have usually been of little more than formal value. In solving practical problems, it has been necessary to develop specific equations, preserving terms that involved the factors important in those problems, and purposefully neglecting other terms that were not of predominating influence. This is the method followed here. It is believed that the solution of the particular problem and the scheme of the solution itself are new.

Jan 1, 1949

By L. S. Richardson, N. J. Grant

Iodide-grade titanium, two oxygen alloys, and two aluminum alloys were studied by means of creep-rupture tests from 1000° to 2000°F. From the test information an evaluation was made of, 1) the relative creep-rupture strengths of the u (hexagonal-close-packed) and 0 (body-centered-cubic) forms of titanium and some of its alloys; 2) the effects of solid-solution strengthening by oxygen and aluminum on the u and 0 structures; and 3) the extent and effect of atmospheric oxygen alloying on rupture life in tests above about 1000°F. THE use of titanium alloys at temperatures above 1000° F has been considered unlikely by most investigators because of low creep strength (based on a requirement for room-temperature ductility, formability, and weldability) and low oxidation resistance. The results of this testing program do not entirely uphold this pessimism in terms of strength and oxidation resistance. The observations described below are based entirely on stress-rupture results, although some creep tests were also carried out on these alloys. Three items of primary importance are covered: 1) Stress-rupture data in the form of the Larson-Miller parameter curves for several titanium alloys at temperatures up to 2000°F; 2) The relative strengths of the hexagonal-close-packed a structure and the body-centered-cubic 0 structure; 3) The effects of solid-solution alloying on the creep-rupture properties of titaniu&apos;m at elevated temperatures. Only two investigatons have reported the creep- rupture properties of titanium at temperatures above 1000° F. Lunsford and rant&apos; tested iodide titanium; their values are also utilized in the paper. EXPERIMENTAL PROCEDURE After a few tests had been made in a conventional creep-rupture test machine, it became clear that some sort of atmospheric protection would be necessary for short-time tests conducted at temperatures above 1600°F, or for times greater than 100 hr at 1200°F or above. Several furnace units and test machines were constructed, the most successful of which is shown in Fig. 1. Certain experimental difficulties peculiar to titanium were encountered; for example, the use of molybdenum holders was dictated because titanium forms low melting-point eutectics with conventional high-temperature alloys containing appreciable amounts of iron, nickel, or cobalt. This same difficulty made the use of chrome l-alumel thermocouples in direct contact with a test specimen impossible, above about 1500" F. The high-temperature high-vacuum furnace shown in Fig. 1 was capable of maintaining a vacuum of better than 10"5 mm of mercury at 2000°F (pressure measured in cold part of system) and 5 X lo-&apos; mm at room temperature. Most of the tests eonducted in vacuum were at temperatures

Jan 1, 1960

By G. D. Cremer, J. J. Cordiano

Aluminum powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, however, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and alumiuum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. A second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age-hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders. is probably the significant factor in our failure to obtain strong sintered pieces. Methods of Puoducing the Powder Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943