Search Documents

By Charles Barrett

METALLURGISTS are making use of the stereographic projection to a steadily increasing extent. In the last five years no less than 20 papers in American metallurgical journals alone have employed the stereographic projection; recent books on physical metallurgy, plastic deformation, X-rays and their applications, and crystal structure use it. Mineralogists have used the stereographic projection for many years in the description of symmetry classes and crystal planes, for it presents an accurate, easily understood plot of any angular relations in crystals with all unessential features eliminated (such as the accidentally deter-mined size and shape of crystal faces). In metallography and physical metallurgy the projection is much used for the analysis of markings appearing on polished grains: slip lines, twins, cracks, structures formed by precipitation, magnetic-powder patterns, etch pits, etc. Data from certain types of X-ray photograms are most conveniently analyzed by its use, particularly those for determining the orientation of single crystals or the preferred orientation of grains in an aggregate. Calculations of how to tilt or cut a crystal parallel to a certain crystallographic plane or to reflect X-rays from a certain plane are rapidly carried out. It has been adopted almost universally to the exclusion of other methods by those studying the deformation of metallic crystals, save where the accu-racy required is greater than a few tenths of a degree. Any directional property in a crystal or polycrystalline material can be shown on a stereo-graphic projection; for example, the modulus of elasticity, yield point, etc. It has been repeatedly called to our attention that there is need of all elementary explanation of the principles and methods of stereographic projection, covering all the, common applications in the field of metal-lography and physical metallurgy. The following contribution is an attempt to fill this need. The description of each method is supplemented with references to publications in which the method has been used. For convenience to the reader, these illustrative references are chiefly in American journals, particularly the publications of the American Institute of Mining and

Jan 1, 1937

By C. M. Shigley

Tan record of the largest magnesium plant in the country utilizing sea water as a primary raw material stands as another victory in the struggle for large-scale production of pure chemical elements from the oceans. Bromine was the first element to be economically and commercially recovered when, in 1933, a six million pound per year unit was built on the Atlantic Coast near Wilmington, North Carolina, by the Ethyl-Dow Chemical Co.1 The bromine was reacted with ethylene to produce ethylene dibromide, a necessary associate of tetraethyl lead in ethyl antiknock fluid. Within eight years that plant was doubled and redoubled, and another large unit was put into operation at Freeport, Texas, taking bromine from the Gulf of Mexico. In 1940, in fortunate anticipation of the impending demand for magnesium and the limitations of the production from natural brines, the Dow Chemical Co. turned again to the sea, and designed and erected a plant at Freeport to produce 18,000,000 lb. of magnesium per year from sea water.2 In March 1941, two months after the new plant had been put into successful operation, construction of an 18,000,000-lb. Government-financed addition was started. Late in 1941, as a part of the $400,000,000 defense program intended to produce 600,000,000 t0 700,000,000 lb. of magnesium per year, Dow was asked to build and operate for the Government a 72,000000-lb. plant near its original plant at Freeport. Within a few days after the Japanese made their attack at Pearl Harbor, preparation of a site was started at Velasco, Texas, for the construction of the Texas plant of the Dow Magnesium Corporation-the largest known magnesium plant utilizing sea water as its raw material. Less than six months after the first piling was driven, urgently needed magnesium was in steady production. Five months later, the plant had exceeded its rated capacity. It remained above rated production until the general magnesium curtailment was applied to Government-owned plants in September 1944. Credit for the construction and operation record of the Dow magnesium plant must be divided among the efforts of a very determined group of men, an extremely favorable location, and a simple process. It is with the two latter aspects of the plant that this article will deal. The site for the new enterprise was chosen near Velasco, Texas, on property bordering the Brazos River at a point approximately 6 miles inland from the original magnesium plant and y miles inland from the Freeport Harbor on the Gulf of Mexico. This location was far enough away from the operating units to reduce both interference from construction and the vulnerability of closely bunched manufacturing operations to the then feared air attack. Yet the distance inland was not too great for the economical construction of a barge canal from the harbor to serve both the transportation of raw

Jan 1, 1945

By D. K. Crampton, H. l. Burghoff, J. T. Stacy

THE effect of cold-working upon electrical conductivity of copper and of copper alloys appears not to be generally known in detail Although several papers on the subject have been presented, showing variable effects according to alloy composition, it is often assumed that the 2 to 3 per cent lowering of the conductivity of ordinary tough-pitch copper by severe cold-working is typical for copper alloys Because of this situation it was decided to carry out the present work upon several types of copper, copper-zinc alloys over the commercial range of brasses, other binary alloys, and numerous age-hardening alloys in the quenched, and quenched and aged conditions The large number of alloys investigated made it impossible to study every one in the detail it may have merited Inasmuch as several interesting points that could not be satisfactorily explained came to light, further work is contemplated by the authors It is usually considered that the normal effect of cold-work on ductile metals and unordered alloys is to decrease conductivity slightly In alloys that are in the ordered state, as annealed or otherwise heat-treated, cold-working tends to disorder the structure, resulting in very marked lowering of conductivity The random state of atomic arrangement produces lower conductivity than the ordered state for the same composition 1 PREVIOUS WORK previous work in the authors' laboratory has shown the electrical conductivity of several copper alloys to be decreased by greater amounts than might have been expected, in view of the general knowledge on the subject, when cold-worked Guillet and Ballay2 investigated the influence of cold-work upon the resistivity of several metals and alloys, including copper and some copper alloys The increase of resistivity due to severe working was less than 4 per cent for all pure metals tested, while the increases for the alloys were generally higher In the copper-zinc alloys, they found that the increase of resistance due to drawing increased with zinc content, and reported a 21 7 per cent increase of resistance for an alloy containing 67 9 per cent Cu as severely worked Masima and Sachs3 studied the change in electrical resistance of three brass crystals when stretched in the tensile test, obtaining increases in resistance of the order of 3 per cent for 30 to 40 per cent reduction of area of the specimens The resistance decreased again when the cold-worked crystals were subsequently annealed Bardenheuer and Schmidt4 found that the conductivity of copper was decreased by 3 to 4 per cent when reduced 50 per cent by working The conductivity of 72-28

Jan 1, 1941

By John K. Berry

The handling and disposal of mine water is a much larger problem than is apparent at first glance. Many more tons of water are removed from underground coal mines in the United States each year than tons of coal. In the old anthracite region of Pennsylvania the average was around 36 tons of water for each ton of coal produced, while bituminous mines average about 5 or 6 tons. Water encountered in the mines may come from several different sources. In mines with light cover and without a firm solid roof, rain may seep directly into the workings. This is also true of deeper mines where pillar falls have broken the roof to the surface. The top under creek beds is generally faulty and broken and water comes through the roof at this point. Deeper mines are frequently overlain by water-bearing strata and pillar breaks and faulty top can admit water, while places running to the dip often accumulate water which comes up through the bottom. In all cases, except where passing under a year-round stream, the amount of water made is usually pretty closely connected with the weather-more water during the rainy season, less in the dry, although the deeper a mine is, the longer it is before changes in rainfall are felt. Another source of water, not connected with seasonal changes, is old water, accumulated over a period of time in abandoned workings of the mine, or from flooded adjacent mines. Here the water filters through the coal, the parting, or comes up through cracks in the bottom. Similarly, core holes, drilled to prospect the property, can be a source of unexpected water and modern safety requirements for dust-allaying water at the working faces can turn a pleasant working area into a soggy mess over the weekend if the system is not properly maintained and operated. Why water must be disposed is obvious. If allowed to accumulate, sooner or later the mine will fill up, or at least it will become "roofed" in low places, blocking ventilation and traffic. But it must also be controlled long before it reaches this stage. Water standing in the working faces is unpleasant for the men who have to work there and also cuts down on the amount of work they can do, as they must watch where they step all the time. It is especially unpleasant in low coal.

Jan 1, 1973

By J. E. Norton

PRODUCTION statistics show that during the period of emergence from the depres¬sion the coal industry was becoming increasingly cognizant of the economic and competitive necessity for mechanizing. About 1935 many of its leaders were becoming aware also of the alarming scarcity of men properly trained to cope with the new problems of mechanization. In order to get a factual statement of this problem, a special AIME Coal Division Committee + was requested to survey the condition. Its investigation disclosed that graduates of mining schools going into coal mining numbered 16 in 1939 and 15 in 1938. With this as a background, Pittsburgh Coal Co. foresaw that a comprehensive program was necessary if it was to enlist the services of trained technical men, who were an indispensable part of a mechaniza¬tion program. The purpose of this paper is to review the program set up, to comment on the successes and failures and to outline the future course of action. SUMMER WORK An inescapable conclusion from the mechanization statistics was that the opportunities in coal mining were good. Not only was there a void in technical skill to fill from past years, but the ac¬celerating rate of mechanization indicated an increasing demand for technically trained men for the future. The remedy lay primarily in presenting facts con¬cerning the coal industry to the under¬graduate engineers before they made their professional occupational choice. Based on this idea, one of the key points in the program - was summer vacation work for the undergraduate, which, through the inducement of summer earnings, brought men into the mines to take a look at the prospects. This was more successful than statistics indicate because the war badly scrambled the orderly working of the program, but it could not obscure the value of a summer work program. A decided advantage was that it gave the company a preview of the graduate. An observation on this part of the program is that it is extremely hard to gauge lower classmen, and we found it wise to give them the benefit of the doubt, as the last two years in college bring about surprisingly rapid develop¬ment in some men. We could readily single out the men at the opposite ends of the scale of competence. COMPREHENSIVE TRAINING PROGRAM Having adopted summer work as a

Jan 1, 1946

By S. H. Ash

Mass production methods, although increasingly important for economic reasons, create new hazards, remove many hazards, and improve health and safety by reducing exposure and obtaining better supervision. Such methods must be efficient or be discarded. Skilled workmen are required who must be trained to utilize equipment that replaces picks, shovels, and explosives. The effects of working conditions on the health of workmen have long been evaluated in noncoal mines. Studies and action programs relating to environmental health hazards in the mineral industry have placed particular emphasis on dusts. The anthracite industry is conducting an action program on the problem of dust. Segments of the bituminous industry are now conducting similar investigations. An industrial hygiene survey of coal mining in the State of Washington has been conducted and the results published in 1949. (State of Washington, Department of Health, I. H. Bul letin 4.) Chest X rays were obtained from miners in the six major coal-producing counties. State Health Department mobile X-ray equipment was set up at most large mines. Participation was on a voluntary basis, and response was obtained from 70 percent. Important in successful mining safety programs are training programs for supervisors and workmen alike. These programs recognize that the employe is the focal point in injury prevention and are planned and function around him. During the war, industries had to compete with each other for workers and to obtain and hold good workers, working conditions had to be made attractive. The average age of the mine worker increased, and, contrary to what many expected, mining injury rates decreased rather than increased. To attract competent workers, risks to life and limb, as well as laborious tasks, have to be reduced, and an experienced worker is indispensable for safety. Young men are returning to modernized mines. Mass production methods and equipment are more to their liking; jobs are more remunerative, demand action, and require special training and skill that give them the mark of a craftsman. Such workmen can be taught safe methods.

Jan 1, 1950

By G. O. Prickett, P. Somasundaran

An experimental progmm based on statistical principles is used for optimizing a flotation operation for the separation of minerals. In this case, flotation of sylvite from sylvinite ore with amine and starch as the flotation reagents was studied to find the optimum reagent levels at various slime levels. The experiments were first done on a two-level three-factor design. Analysis of the results showed that the interactions between various factors were significant. Hence, a first-order linear model of the flotation response would not be accurate. The two-level three-factor design was expanded into a composite design in order to test the fit of a higher-order model. Data were treated to obtain an expression for flotation response as a function of the different variables, to predict the optimum reaaent levels at various slime levels, and also to determine the path of steepest ascent. Tests around the predicted optimum and along the path of the steepest ascent were done until a near-optimum region was obtained. Exploration of the nature of the response surface in that region established the actual location of the maximum response. The optimum amine level was found to be 0.20 lb of amine per ten of ore at all slime levels, while the optimum starch level varied as a function of the slime present. Computer access at the laboratory by means of a teletype terminal on a commercial time-sharing system enabled efficient and accurate treatment of experimental data. The efficiency of experimental investigations can be improved significantly by the use of experimental design and data analysis based on statistical principles. The common approach used in experimental research is to study a property of a system as a function of "one-variable-at-a-time". Several authors'-4 have pointed out the inadequacy and deceptiveness of this method. Results obtained for the effects of a variable on the measured response of the system using

Jan 1, 1970

By J. W. Rutter, K. T. Aust

In previous studies of grain boundary migration in zone-refined lead, the authors used bicrystal specimens consisting of a striated crystal which was grown from the melt, and an adjacent striation-free crystal, introduced by artificial nucleation and growth.1 While this method permits the study of the motion of individual grain boundaries, it does not provide control of the relative orientations of the grains. The present note will describe a technique for controlling the orientations of the two crystals in this type of specimen. The technique consists essentially of placing a striated crystal and a striation-free crystal of controlled orientations end-to-end in a graphite trough, then melting a short zone at the junction of the two crystals and allowing it to freeze to form the desired grain boundary. The apparatus used to carry out this process is illustrated in Fig. 1. It consists of a trough milled from high-purity graphite,with grooves in the underside for the placement of thermocouples. The graphite piece fans out on one end at the level of the bottom of the trough; the sides of the trough are completed in this region by the attachment of a mating plate with a slot cut at any desired angle to permit reorientation of the crystal placed at this end of the assembly. The joint between the crystals is made at or near the point where the slotted plate joins the rest of the trough. The thermocouple slots are deepened in this region so that the thermocouples are separated from the melt by only 1/32 in. of graphite. An induction heater, with suitable temperature control, is used to obtain the molten zone. The two single crystals used are first chemically polished in a solution consisting of eight parts glacial acetic acid and two parts 30 pct hydrogen peroxide. They are then placed in the trough with the ends to be joined at the position of the thermocouples. Next, cooling is applied to the two crystals by means of air

Jan 1, 1962

By Edmund M. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence-the total absence of noise except for one's own breathing and scuffing of boots on the bottom. An underpound mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working in the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur. But excessive noise is a health hazard. In recognition of this fact, our congress included noise exposure as a part of the "Coal Mine Health and Safety Act of 1969." As [Fig. 1] indicates, allowable noise exposure is established by specifying a time duration permitted at different noise levels. This is the well known "Walsh-Healey" criteria which govern noise exposure in many industries. In most industries noise exposure is not a constant value. Noise emitted from coal mining machinery varies widely, and therefore interpretation of compliance is not a simple matter. Time, environment, instrumentation and machine productivity, as well as the designed machine characteristics affect the results. It is the purpose of this paper to present the underground coal face machinery noise problem from a manufacturer's point of view. Manufacturers are very much aware of their responsibility to alleviate the noise problem. Not infrequently, orders are received from coal operators that a given new machine must comply with "The Coal Mine Health & Safety Act" noise regulations. Such a request is indicative of the misunderstanding which exists with machine users, while indicating their desire to comply with the law. Obviously, if all machinery could be designed and used at some arbitrary low noise level, it would be possible to simplify the regulations. However, there still remains the pervasive problem of existing machines. Extensive investigation to create practical retrofit kits for existing machines, to substantially reduce noise have been only marginally successful. Certain machine mechanisms are inherent noise makers. The only really good solution is to substitute a quieter mechanism. Such overall new designs have been undertaken, and several examples are mentioned later in this paper. Before describing machine noise problems, it is necessary to define noise values. Noise levels are measured in decibels. The designation "DBA" is decibels measured on the "A" scale, or one in which the frequency sensitivity of the instrumentation is about the same as the human ear. The numbers are often misinterpreted because it is a logarithmic, rather than an arithmetic scale. In comprehending the numbers, it should be remembered that any increase of 3 dB doubles the sound power. In practical terms this means that two noises of equal power at the same distance away increases a dB reading by three. Consider [Fig. 2] showing a simplified case of a worker on a machine subject to

Jan 1, 1980

By Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodity in this volume has as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as fluxes, glass raw material, refractories, fillers, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Recent. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited avail- ability in certain areas. Limestone and dolomite are so useful and so abundant that in 1972 more than 690 million tons were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses, with emphasis on developments since 1960. In doing so we borrowed extensively from our recent report on the applied geology of limestone and dolomite (Rooney and Carr, 1971). The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired down in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information.

Jan 1, 1975

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies' was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.

By P. B. Bucky

In previous publications1 it was shown that a scalar model of any weighty structure, where the stresses produced are mainly due to gravitational forces, will behave similarly to its prototype if the model and prototype material are the same and the model is placed in a centrifugal field of force (substituted for the gravitational field) which has been increased in the same proportion as the linear model scale is decreased. This principle is now being applied to a study of the behavior of mine structures in an attempt to determine the laws that control them. The importance of using models as a means of solving mining problems has been discussed previously, yet it may be well to reiterate here that this method of research and type of solution have been productive of far-reaching results in other engineering fields, notably those of hydraulics and aerodynamics. Model research is a comparatively cheap and time-saving method of checking practical experience. Up to the present time the best guide to what will happen underground has been the judgment of the man who has observed most and been longest acquainted with the local conditions. His experimental work underground is limited by the elements of cost, time and danger, while failure is seldom permissible. In a model, as in a test tube, all elements that affect the solution of a problem are under definite control. Each element may be varied independently at hill and its effects noted. Experimental work on a small-scale model may therefore be performed at a comparatively small expenditure of time and money, instead of on a full scale in the mine, where the cost, time, and danger elements are necessarily great. The experiments described in this paper are to be considered as part of a progress report and a continuation of Technical Paper 425. One object of the research program is to make each experiment point the way for further research on that particular phase of the general problem. The results and conclusions presented here are therefore not to be considered as final, but arc to be interpreted as

Jan 1, 1934

By M. Schussler, J. S. Brunhouse

Arc-melted and electron-beam melted tantalum in the cold-worked and the recrystallized conditions showed high strength, good tensile ductility, and excellent notch toughness down to 321°F. Arc-melted material, containing moderate amounts of interstitials, possessed better short-time strength than higher purity electron-beam melted material up to 2000°F. Cold-working substantially strengthened arc-melted tantalum, whereas electron-beam melted material exhibited a low work-hardening rate and possessed better formability characteristics. With identical compositions and microstructures, the mechanical properties of melted tantalum and uacuum-sintered tantalum should be similar. TANTALUM metal usage is increasing rapidly in a number of applications. The outstanding chemical corrosion resistance of tantalum accounts for its applications in chemical processing equipment for severe service conditions and for surgical uses in the medical field. The largest present requirements for tantalum are in the electronics industry, where its special properties are useful in capacitors. The high melting point (5425°F) and inherent ductility of tantalum also suggest that tantalum and tantalum-base alloys might offer an excellent combination of high strength at very high temperatures and good fabri-cability. Pure tantalum has been used in significant amounts in parts requiring high-temperature strength, such as heating elements, reflectors, and heat shields in high-vacuum high-temperature furnaces and in electronic tubes. A few very promising tantalum-base alloys have been developed and are being investigated extensively. The possibilities for tantalum as a high-temperature structural material, either unalloyed or alloyed, will become better defined when more extensive mechanical property data are known. pughl measured the tensile properties of vacuum-sintered tantalum in sheet form for the temperature range of 78" to 1500°K (-321' to 2240°F), and Bechtold reported data obtained at low temperatures.' Drennen3 determined creep and stress-rupture properties of both vacuum-sintered and arc-melted tantalum sheet at 1200 °F. Some additional data on the mechanical properties of tantalum at temperatures up to 5000 °F have been summarized elsewhere.4'5 It is probable that large structural shapes of tantalum, either unalloyed or alloyed, can most readily be produced from ingots prepared by melting. Consequently, the present investigation was undertaken to determine more extensive short-time mechanical properties of tantalum metal consolidated by melting. EXPERIMENTAL PROCEDURE Melting and Fabrication—Two tantalum ingots were utilized in this study to obtain information on the effect of interstitial elements on mechanical properties. Both ingots were melted from Union Carbide Metals Co. tantalum dendrites.

Jan 1, 1961

By A. M. Gaudin

THE study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a, substantially definite size which depends upon the ball size 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with-all the crushers tested. 7. Different methods of crushing produce grains of different shapes.

Jan 2, 1926

By Maxwell Gensamer, Vsevolod N. Krivobok

It is generally recognized that "low temperatures" have a definite effect on the properties of metals and alloys. Furthermore, it is also generally understood that the effect is decidedly adverse. The possibility that the same low-temperature treatment might be employed for the purpose of improving certain properties of the alloys has received less attention until recently, and the experimental and theoretical knowledge consequently is meager. The effect of low temperatures may be studied in two ways: by studying such properties as tensile strength, hardpess, impact resistance, etc., at low temperature, and by studying the properties of alloys at room temperature after these alloys have been subjected to a low-temperature treatment. Even in the latter case, certain properties will differ materially from the same properties obtained on identical material but without cold treatment. In other words, subjecting alloys to cold treatment results in an irreversible change in mechanical properties. Changes of this character are usually indications of the appearance of a new phase or phases, and would be likely to occur in alloys which, either by virtue of their composition or by heat treatment, are retained at room temperature in a metastable condition. Consequently, studies of the effect of low temperatures logically should be conducted from the physicochemical point of view, since the results of such studies not only would furnish metallurgists with interesting theoretical data but would clearly indicate the classes of alloys that would hold promise of improvement, and, possibly, of new applications. As the present investmigation deals with chromium and chromium-nickel alloys of iron of the stainless variety, it has been thought desirable to present the data concerning low-temperature properties of these alloys, available from the most recent and most comprehensive work of H. S. Russell.l A summary of these data is given in Table 1. The data are confined to a limited number of alloys of the type dealt with in the present

Jan 1, 1931

By R. W. Heckel, R. E. Trabocco

The recovery process in 400 Monel filings was followed, principally, by using the Warren-Averbach technique of X-ray peak profile analysis. The deformation fault probability, a, was 0.006 in samples of unannealed filings. a , the twin fault Probability , was approximately 0.002 in samples of unannealed filings. Both a and 0 were found to "anneal out" at 600°F. The effective particle size and mzs strain increased and decreased in the (111) direction, respectively, with increasing annealing temperature. The actual particle size was found to be almost equivalent to the effective particle size. Tile small values of deformation and twin fault probabilities accounted for the similarity in values of the effective and actual particle sizes. Stored strain energy and dislocation density calculations based on rms strain decreased with increasing annealing temperature. The dislocation density decreased from 10" per sq cm in the unannealed filings to 10' per sq cm in the partially re-crystallized filings. The square root of the dislocation density based on strain to that based on particle size indicated a random dislocation distribution in the unannealed filings. The dislocation arrangement changed to one with dislocations in cell walls with increasing annealing temperature. THE recovery processes which occur in metals are generally thought to be a redistribution and/or annihilation of defects.' Investigators' have shown that recovery processes can be characterized by X-ray line-broadening analyses. Michell and Haig4 measured the stored energy of nickel powder by calori-metry and found the value to be greater by a factor of 2.5 than that from X-ray data obtained by the Warren-Averbach technique.= Minor increases in particle size occurred up to 752°F (recovery), while above 752°F the particle size increased greatly due to recrystalliza-tion. X-ray microstrain values decreased between room temperature and 392"F, remained constant from 392" to 752"F, and decreased from 752°F to a negligible value at 1112°F. Faulkner developed an equation for calculating stored strain energy based on X-ray line-broadening data which gave a closer correlation of measured and calculated stored strain energy based on the data of Michell and Haig. The stored strain energy released during recovery is predominately dependent on the decrease in dislocation density which was p-enerated from cold work.7 Stored energy has been measured8 in alkali halides during recovery and recrystallization and 80 pct of the stored energy was found to be released during recovery. Dislocation distributions have been studiedg in a number of fcc metals by thin-film electron microscopy. Howie and Swann" found the stacking fault energy of copper and nickel to be 40 and 150 ergs per sq cm, respectively. ~rown" has pointed out that these stacking fault energy values should be corrected to 92 and 345 ergs per sq cm, respectively. The dislocation distribution of a metal is directly dependent on the stacking fault energy of the system. Metals of high stacking fault energy such as aluminum cross-slip readily and do not form planar arrays of dislocations. Metals of lower stacking fault energy such as stainless steels" do not cross-slip readily. Cold-worked nickel has been found to form a cellular dislocation structure after annealing.13 The relatively high stacking fault energy of nickel and copperlo to a lesser extent favor cellular structures of dislocations rather than planar arrays after deformation. The present study of recovery was carried out on a Ni-Cu alloy (Monel 400) to compare with prior studies for pure nickel and pure copper. X-ray line-broadening techniques were used to measure the effect of recovery temperature on rms strain and particle size and the results were compared with previous studies on copper'4-'7 and nickel., Calculations were also made on stacking fault probabilities, dislocation density, dislocation distribution, and stored strain energy as affected by temperature. EXPERIMENTAL PROCEDURE The nominal analysis of the Monel 400 used in this investigation was: 66.0 pct Ni, 31.5 pct Cu, 0.12 pct C, 0.90 pct Mn, 1.35 pct Fe, 0.005 pct S, 0.15 pct Si. The annealed material was cold-reduced in two batches, one 50 pct and the other 80 pct. It was originally planned to conduct line-broadening studies of these bulk samples; however, rolling textures that developed produced low-intensity peaks which were not suitable for line-broadening analysis. Filings were prepared at room temperature from both the 50 and 80 pct cold-reduced specimens, series A and series B, respectively, and were not screened prior to heat treatment or X-ray studies. Heating to the annealing temperature, 200" to 120O°F, was accomplished in a matter of minutes in a hydrogen atmosphere. Following heat treatment, some of the filings were mounted and polished for microhardness measurements with a Bergsman microhardness tester, using a 10-g load. A G.E. XRD-5 diffractometer using nickel-filtered Cum radiation was used to obtain all diffraction patterns. Only (111)- (222) line-broadenin data were used in the present study since the {400f peaks were too weak to use. The Fourier analysis of the (111) and (222) peak

Jan 1, 1969

By Aloys H. Wohlrab

THE conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. CONVENTIONAL DRILL BIT IN USE That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8 -in. steel show that when bit sizes are reduced from I ½ in., I 3/8 in., and I 3/16 in., to I 3/8 in., I ¼ in., and I 1/8 in., respectively, the volume of the hole is 15 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I.826 in., a difference of 0. 2,5I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and I4° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr characteristics) by some mines.4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as can be forged economically. Shop practices and costs have been discussed in earlier papers.5.6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert.7 REQUIREMENTS FOR DETACHABLE BIT FOR HOLLINGER Under these circumstances, it was apparent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1942

By R. H. Card

The geophysicist is interested greatly in the resistivities of different formations or parts of the earth's crust; sometimes he is interested in a single figure in the nature of an average, or what may be called the effective resistivity, of all the formations or parts of the crust at a given location to a certain depth. Conversely, the engineer whose work is concerned with the coordination of power and communication lines in such a manner as to avoid electrical interference between these two types of facilities is concerned very much with this effective resistivity; to a lesser extent he is interested in the resistivities of individual formations. In connection with his work the coordination engineer often estimates the effective resistivity of the earth from measurements of the mutual impedances of lines; in other instances he derives from measurements of a different type the resistivities of different layers of the crust and synthesizes these to obtain an estimate of the effective resistivity. In connection with problems concerning the coordination of power and telephone lines, measurements from which earth resistivities can be estimated have been made at many points in the United States by the American Telephone and Telegraph Co. and its associated companies, in cooperation with various power companies and with railroad companies having electrified sections of line. Other such measurements have been made by the Joint Subcommittee on Development and Research of the Edison Electric Institute and the Bell Telephone System. A study has been made of the correlation of these data with the ages and types of materials of the strata of the earth's crust at each of the test locations. The purpose of this study has been primarily to provide information to assist in predicting the order of magnitude of effective resistivities to be used in the preliminary consideration of problems concerned with the coordination of power and communication lines. To make the results of such a study most useful, it is essential that the geological data to be secured when such a prediction is wanted be readily obtainable. Data on the ages of strata and the types of materials composing geological structures can usually be obtained, therefore particu-

Jan 1, 1940

By R. H. Card

The geophysicist is interested greatly in the resistivities of different formations or parts of the earth's crust; sometimes he is interested in a single figure in the nature of an average, or what may be called the effective resistivity, of all the formations or parts of the crust at a given location to a certain depth. Conversely, the engineer whose work is concerned with the coordination of power and communication lines in such a manner as to avoid electrical interference between these two types of facilities is concerned very much with this effective resistivity; to a lesser extent he is interested in the resistivities of individual formations. In connection with his work the coordination engineer often estimates the effective resistivity of the earth from measurements of the mutual impedances of lines; in other instances he derives from measurements of a different type the resistivities of different layers of the crust and synthesizes these to obtain an estimate of the effective resistivity. In connection with problems concerning the coordination of power and telephone lines, measurements from which earth resistivities can be estimated have been made at many points in the United States by the American Telephone and Telegraph Co. and its associated companies, in cooperation with various power companies and with railroad companies having electrified sections of line. Other such measurements have been made by the Joint Subcommittee on Development and Research of the Edison Electric Institute and the Bell Telephone System. A study has been made of the correlation of these data with the ages and types of materials of the strata of the earth's crust at each of the test locations. The purpose of this study has been primarily to provide information to assist in predicting the order of magnitude of effective resistivities to be used in the preliminary consideration of problems concerned with the coordination of power and communication lines. To make the results of such a study most useful, it is essential that the geological data to be secured when such a prediction is wanted be readily obtainable. Data on the ages of strata and the types of materials composing geological structures can usually be obtained, therefore particu-

Jan 1, 1940

By J. H. Carpenter

LMENITE, rutile, zircon, and other heavy minerals are found in small amounts in the sand that covers most of Florida. Small enriched deposits occur on the beaches and coastal dunes. One beach deposit east of Jacksonville was worked during World War I and another near Vero Beach during World War 11. Both ceased operation when the resumption of imports reduced prices. Early in World War II reduction of rutile imports made a domestic source of the mineral necessary to maintain the expansion of armaments. Explorations made near Jacksonville discovered a relatively large body of low-grade ore about 10 miles inland from the beaches. A plant installed by Rutile Mining Co. of Florida using both flotation and tables encountered difficulties because of low plant capacity and organic slimes in the ore. In 1944 Humphreys Gold Corp. solved the problem of concentrating the low-grade ore by using the newly developed Humphreys spiral concentrator and by mining with a hydraulic dredge. This combination of low cost mining and concentration permitted the plant to continue operation in competition with foreign ores when imports were resumed following the war. The success of the Jacksonville operation renewed interest in Florida as a source of titanium. An extensive survey of the state was made by E. I. du Pont de Nemours and Co., Inc., under the direction of J. L. Gillson in 1945 to 1946. Sampling was carried on by drive pipe drilling to depths of 20 to 25 ft. Encouraging values were discovered near the location of the present Trail Ridge mine, 50 miles southwest of Jacksonville, near the town of Starke. The United States Bureau of Mines was interested in exploring for heavy minerals in Florida, and on the recommendation of both the state geologist of Florida and of Du Pont geologists, drilled deeper where marginal indications were found on Trail Ridge. In 1947 it was discovered that sufficiently higher values occurred at depth to make the deposit commercial. The orebody at Trail Ridge is a long sand deposit averaging about 1 mile in width and 35 ft in depth. It is approximately 1 1/2 miles wide at the north end of the portion now being worked, tapering to a blunt point 3 miles to the south. The ore reaches a maximum depth of 65 ft near the center and feathers out into barren sand at the edges. The ground surface is relatively flat and is covered with vegetation including pine, scrub oak, palmetto, and occasionally in swampy areas, cypress. The remain of a dense woody growth underlies and marks the bottom of the Ore 'One. It is difficult to drill through this layer, but in some cases where it is less than 5 ft thick it has been possible to drive through the wood. Sand lying below is coarser than that in the ore zone and contains no values. The wood layer consists of unconsolidated carbonized fragments of branches and other forest trash associated with a considerable amount of ar-

Jan 1, 1954