Search Documents

By D. J. McAdam, G. W. Geil, D. H. Woodard, W. D. Jenkins

INTRODUCTION IN a series of papers, the authors and their associates have shown that the resistance of a metal to fracture is a function of all three principal stresses. 10-18,20,21,23,[1] Consequently since a technical cohesion limit is defined as the technically determinable resistance to fracture, under a specific stress system, the technical cohesive strength comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. As shown in the previous papers, the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,§ namely, the stress system, plastic deformation, temperature, and the strain rate. The effect of each of these factors on the fracture stress is qualitatively the same as its effect on the flow stress. The effect of any of the factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. Since the term "fracture stress" has come into general use with the same significance as technical cohesion limit; the authors are here using the' shorter term with the understanding that it, does not always refer to actual fracture. In the general investigation described. in the previously-mentioned papers,10-18,20,21,23 the influence of the stress 'system on the fracture stress was studied by means, of tension tests of notched specimens. When a circumferentially notched cylindrical' specimen is subjected to longitudinal ten-, sion, the minimum cross section is under " transverse radial tension. The mean radial stress increases with the depth and sharpness of the notch, but is always less than the longitudinal stress. The greatest principal stress (S,), therefore, is longitudinal, and since the radial stress is effectively equal to the circumferential stress, the transverse principal stresses are equiaxial in that plane (S2 = S3). By the use of notched specimens in tension tests it was shown that the fracture stress increases with increase in the radial stress ratio (S3/SI). The evidence is based not only on the results of tests to fracture at various constant temperatures, but also on. results of two-stage tests, in which each specimen was plastically deformed a predetermined

Jan 1, 1948

By H. Landssberg

Subsidence caused by mining operations has been a matter of interest for the mining engineer for just 111 years, since the Belgian committee for study of subsidence in the city of Liege submitted its first report in 1825. This interest is fairly expressed in the enormous amount of literature that has since appeared on this subject. A bibliography, probably far from being complete, which preceded this study as a preliminary survey, comprises more than 800 titles. In spite of this fact the problem remains today as acute as it has ever been. The questions of as good a recovery as possible of the national resources, the safety of the operations, and the protection of private and public property are the important angles from which to look at the problem. The Problem To systematize an investigation regarding the effects of mine excavations two different aspects have to be dealt with: (1) the subsidence of the immediate roof above the workings, affecting the safety of the workers and the progress and efficiency of the operations; (2) the subsidence of the surface, which is also, from the point of time, the second event. The immense importance of surface subsidence as regards the impairment of surface structures of every kind in a mining area is self-evident. Both effects result from reactions of the strata overlying the excavations and they depend mainly on the extent of the excavations and the structure and geological condition of the strata. It has been stressed repeatedly, in this country principally by G. S. Ricel,† that for the understanding of the phenomenon of subsidence accurate surveys are the most urgent necessity. In the past, however, at least in the normal course of mining operations, these surveys have been very crude. The control of the roof in the mine is left to the observation of the behavior of the timber, warning cracks and sounds in roof and walls and to the general judgment and experience of the worker and his supervisors. In any given case this may or may not be sufficient to prevent fatalities but certainly it does not give any accurate information as to what is happening in roof and strata. On the surface, principally in endangered areas, surveys have been conducted more frequently, but also in this case usually weeks or even

Jan 1, 1936

By H. Landssberg

Subsidence caused by mining operations has been a matter of interest for the mining engineer for just 111 years, since the Belgian committee for study of subsidence in the city of Liege submitted its first report in 1825. This interest is fairly expressed in the enormous amount of literature that has since appeared on this subject. A bibliography, probably far from being complete, which preceded this study as a preliminary survey, comprises more than 800 titles. In spite of this fact the problem remains today as acute as it has ever been. The questions of as good a recovery as possible of the national resources, the safety of the operations, and the protection of private and public property are the important angles from which to look at the problem. The Problem To systematize an investigation regarding the effects of mine excavations two different aspects have to be dealt with: (1) the subsidence of the immediate roof above the workings, affecting the safety of the workers and the progress and efficiency of the operations; (2) the subsidence of the surface, which is also, from the point of time, the second event. The immense importance of surface subsidence as regards the impairment of surface structures of every kind in a mining area is self-evident. Both effects result from reactions of the strata overlying the excavations and they depend mainly on the extent of the excavations and the structure and geological condition of the strata. It has been stressed repeatedly, in this country principally by G. S. Ricel,† that for the understanding of the phenomenon of subsidence accurate surveys are the most urgent necessity. In the past, however, at least in the normal course of mining operations, these surveys have been very crude. The control of the roof in the mine is left to the observation of the behavior of the timber, warning cracks and sounds in roof and walls and to the general judgment and experience of the worker and his supervisors. In any given case this may or may not be sufficient to prevent fatalities but certainly it does not give any accurate information as to what is happening in roof and strata. On the surface, principally in endangered areas, surveys have been conducted more frequently, but also in this case usually weeks or even

Jan 1, 1936

By J. Philibert, A. G. Guy

Diffusion in the presence of deformation was studied by the method of vacuum dezincification of copper-rich and silver-rich solid solutions containing 7 to 30 pct Zn. The specimens were designed to permit the study of diffusion in separate portions of a given specimen characterized by strain rates ranging from essentially zero to approximately 10 sec-. No effect of deformation on diffusion was observed. BEGINNING with the work of Buffington and Cohen: interest in the question of the effect of stress or strain on diffusion has largely been concentrated on the enhancement of diffusion in specimens subjected to Continuous plastic deformation. The present research is a contribution to this limited area. However, as a preliminary to focusing attention on this special topic, it will be desirable to make a broad survey of the larger question, especially since there has been considerable foreign work in areas outside those of current interest in the United States. Since most of the topics referred to in the following section are both complex and imperfectly understood at present, it has been expedient in most instances to offer only a guide to the general nature of the work rather than a critical evaluation. PREVIOUS WORK The effect of elastic stress on diffusion has received considerable attention, especially with regard to the thermodynamic driving force for diffusion. The thermodynamic treatments have been based on the work of Gibb, Voigt, Planck, and Leontovich.' Konobeevskii and Selisski6 made a first attempt at treating the problem in 1933, and Gorskii7 a few years later gave a solution applicable to single crystals as well as to polycrystalline specimens. In 1943 Konobeevski8 published treatments that have been the basis of much Russian work up to the present. For example, Aleksandrov and Lyubov used his work in explaining the velocity of lateral growth of pearlite. Early work in the United States was that of Mooradian and Norton, which showed that lattice distortion tends to be relieved before it can significantly affect the diffusion process. Druyvesteyn and Berghoutl1 observed a slight effect of elastic strain on self-diffusion in copper, while de Kazinczy12 found that both elastic and plastic deformation increased the rate of diffusion of hydrogen in steel. On the other hand, Grimes58 observed no effect of either elastic or plastic straining on the diffusion of hydrogen in nickel. High-frequency alternating stresses have been reported by various investigator s13-l5 to increase the rate of diffusion. A special form of elastic stressing is the imposition of hydrostatic pressure, a condition that is amenable to Conventional thermodvnamic analysis. Most of the experimental results in this area are consistent in showing a slight decrease in diffusion rates at high pressures.16-l8 Although Geguzinl reported a pronounced effect of relatively small pressures, Barnes and Mazey20 failed to Corroborate this finding, while Guy and Spinelli21 advanced an explanation of the phenomenon observed by Geguzin. It has been recognized that the thermodynamic treatment of diffusion phenomena in an arbitrarily stressed body is complicated by the fact that the desired state of quasi-equilibrium of the shear stresses cannot be maintained during a general diffusion process. However, attempts have been made by Meix-ner22-24 and Fasto to treat certain restricted cases, such as relaxation. FastovZ7 has also incorporated the general stress tensor into the thermodynamics of irreversible processes. The lattice strain that accompanies the formation of a solid solution has been the subject of much study,28-s0 and indirectly it has entered into many recent theories of diffusion. However, some Russian investigators31'32 have taken other views of this matter and have predicted large effects on diffusion rates because of concentration stresses.o In completing this brief resume of previous work involving elastic strains and before proceeding to a consideration of the effect of continuous plastic deformation, it should be pointed out that deformation of various additional types may also influence diffusion. The effect of cold-working on subsequent diffusion has been studied directly by AndreevaS and by Schumann and Erdmann-Jesnitzer, while indirect evidence has been obtained by Miller and Guarnieri and by Vitman.38 Thermal stresses may also influence diffusion, contributions to this subject having been made by Fastovs7 and by Aleksandrov and Lyubv. The work of Johnson and Martin,o Dienes and Damask,3Band DamaskS considered the question of radiation-enhanced diffusion. In considering previous work on the subject of plastic deformation and diffusion, attention will be directed to those studies concerned primarily with diffusion rather than with its relation to Creep, e.g., the work of Dorn, or to the acceleration of diffusion -controlled reactions. Observations of the effect of

Jan 1, 1962

By G. U. Greene

The various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulphur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1)† states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As. Experimental Work In the present research, the author used for methods in an attempt to determine the composition of the various phases: (1) chemical, (2) microscopic, (3) roentgenographic and (4) thermal. Previous to this research, considerable time had been spent making analyses of different speisses, but unfortunately no very definite conclusions could be made as a result of these analyses.

Jan 1, 1937

By R. G. Clay, C. F. Seaman

THE mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 05 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that time, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to he used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered, the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. ORIGINAL EQUIPMENT AND INSTALLATION A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would he available at each shaft for places where there were no regular blasting stations and could he used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots and the up position would connect it to the line from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1942

By Donald B. Hunter

The Ti-Be system up lo 10 wt pct Be with cortlmercialll' pure titanium has been determined using metal-lographic techniques. Beryllium forms the p eutec-toid type of dinqarz with titanium; the eutectoid occurs at 0.5 xt pct Be azd 1500 F, while an eutectic is foritled at 1887°F containing between 5 and 7.5 rt pct Be. The solubility of beryllium in a titanium does not exceed 0.05 zvt pct and the maximum solubility of Beryllim in 0 titanium is 1 wt pet. PREVIOUS work on the Ti-Be phase diagram indicated that additions of beryllium to titanium resulted in a marked lowering of the melting point,''' and it was also observed that the solubility of beryllium in both a and p titanium was retricted.- With the limited data available, McQuillan and McQuillan constructed a partial hypothetical diagram of the Ti-Be system,= assuming that beryllium formed the 0 eutectoid type of system with titanium. Subsequently Bedford published a tentative diagram of the entire Ti-Be system: although he did not investigate alloys containing less than 10 wt pct Be. This diagram included several compounds described by other authorities.'-l3 The following account describes work directed toward determining the form of the titanium-rich portion of the phase diagram up to 10 wt pct Be. MATERIALS AND METHODS Titanium sponge and a master alloy containing 25 wt pct Be were used in the formulation of the alloys; the chemistry of these materials is detailed in Table I. The alloys were prepared as 250-g compacts which were melted into buttons by arc melting under purified argon on a water-cooled copper hearth. Results of analyses for beryllium are shown in Table I but no determination of other elements was made at this stage. The alloys were hot-rolled at 1650°F to produce 0.1-in.-thick sheet. Alloys containing up to 1.5 pct Be were fabricated without trouble; samples containing 2 pct cracked initially upon hot rolling, but thereafter rolled satisfactorily to sheet. The 5, 7.5, and 10 pct were hot short and could not be rolled. Surface contamination was removed from samples by sandblasting and pickling in a 5 pct HF-35 pct HNOs solution. For metal log raphic examination, heat-treated specimens were mounted transverse to the rolling direction, ground on silicon carbide papers of increasing fineness to 600 grit, and electropolished at 20 v using a solution containing 600 ml of methanol, 60 ml of perchloric acid, 360 ml of butyl cellosolve, and 2 ml of Solvent "X". Difficulty was experienced in obtaining good electropolished surfaces with samples containing more than 1 pct Be, the degree of difficulty in-

Jan 1, 1967

By J. H. Hollomon, J. C. Fisher

THE fundamental problem concerning the fracture of both crystalline and noncrystalline solids is the divergence between the actual and the theoretically computed fracture stresses; the stress required for fracture, computed from the forces between atoms, is many times that actually observed with commercially available materials. Computations have been made1, 2 indicating that the theoretical fracture stress should be from 100 to 1000 times that actually observed. There are other incidental problems that have arisen, perhaps the most important of which is the problem of size effect often observed in the measurement of the fracture stress of non-metallic solids, such as glass. Another effect concerns the relation between deformation and the stress required for fracture. Experiments recently made with pearlitic steels indicate that the tensile fracture stress increases with increasing tensile deformation and decreases with increasing prior compressive deformation. This marked anisotropy of the effect of deformation on the fracture stress is in contrast with the essential isotropy of the flow stress. Early experiments on rock salt crystals by Joffé, et a13 have illustrated the effect of tensile strain in increasing the tensile stress required for fracture. A consistent theory must be constructed that will explain not only the divergence of the measured fracture stress from the theoretical value, the size effect, and the effect of deformation; but will also explain and predict the effects of combined stress, of temperature, of strain rate, and of metallurgical structure. With respect to this last variable, it has now been relatively well established that the carbide particle is the element of structure controlling the fracture of steels. In steels carbide particles vary in shape from plates to spheroids. It has been found that not only does the magnitude of the fracture stress depend upon the size and shape of these particles, but also its dependence upon strain is affected by changes in shape and size of the particles. The precipitate resulting from the age hardening of duralumin also modifies the fracture stress of this alloy. Nonmetallic inclusions greatly lower the fracture stress of all metals. The magnitude of the lowering depends on the size and shape of the included particles. In glass, the major source of the low fracture stress has been fairly conclusively demonstrated by Griffith4 to arise from real flaws or cracks present in the material. He showed that the stress concentration at the end of a defect was of sufficient magnitude to raise the stress at this location to a value comparable with the theoretical strength of the material. If the cracks were reduced in size, Griffith showed that the observed fracture strength increased by virtue of the decrease in stress concentration. He also pointed out that cracks disposed perpendicularly to the applied tensile stress would be more effective in lowering the fracture

Jan 1, 1947

By Edwin M. Chance

During the last decade many conditions have been encountered that have materially increased the cost of the production of coal. As in most cases it has not been practicable to increase the selling price of such coal sufficiently to insure the necessary margin of profit, the mine management has been forced to avail itself of what might be termed unusual means that costs might be held at as low a figure as possible. The so-called efficiency engineer has been called upon, costly power plants have been built and machinery has been installed to replace manual labor wherever possible. Another aid used recently to secure economies through the more intelligent production of coal, is the chemist. As the coal industry, barring the production of byproduct coke, does not at once give evidence of its need of the services of the chemist, the writer will endeavor to point out a few of the services that this branch of the staff has been able to render. The preparation of coal in the past has been carried on entirely upon an empirical basis, that is, the criterion adopted has been an ocular inspection. Unfortunately, the appearance of a coal and especially of an anthracite, has but little relation to its fuel value, and as long as coal is purchased for the heat that can be obtained from it by its combustion, the quantity of such heat that is purchased must be one of the principal desiderata in selecting or preparing a coal. Were coals purchased for use as bric-a-brac or for exhibition in museums it might be both wise and just to purchase them upon their appearance. After 4 or 5 years of investigation the fact has been established that coals of very inferior appearance, and I now have special reference to anthracite, might and often did possess heating and burning properties superior to those possessed by bright coals which in the past had commanded considerable and uniform premiums in the market. This being the case the question arose as to whether the trade could be convinced of this fact. While at first some difficulty was experienced in establishing the quality of such dull coals, still it was found that the real obstacle to the sale of these materials in the past had been the fact that the coal producers' own sales departments felt convinced of the inferiority of this type of fuel and when complaints were registered they were given ready credence. Upon convincing the sales department of the quality of this type of fuel, but

Jan 1, 1917

In the past few years the hydraulic aspects of rotary drilling have received considerable attention. It is generally recognized that accurate prediction of circulating pressures is desirable, particularly in those areas where a delicate pressure balance is necessary to prevent both blowouts and lost circulation. For calculation purposes the standard hydraulic equations for the pipeline flow of Newtonian fluids have been altered to facilitate similar calculations for non-Newtonian or plastic fluids.'.' This latter classification includes most colloidal types of drilling muds. Two properties: plastic viscosity, un, and Bingharn yield value, Y,, are commonly used to define the flow characteristics of a plastic fluid. These are commonly obtained with multispeed viscosimeters such as the Fann V-G meter.3 Normally these measurements are obtained at some surface temperature, and are not corrected to circulating temperatures for calculation purposes. This may result in considerable error, particularly in the laminar flow calculations which comnlonly apply to the drill pipe-borehole annulus. The purpose of this study was to investigate the effect of temperature on the flow properties of some water-base muds. A laboratory model Fann V-G meter was used for measurement of viscosities, yield values and gel strengths. An aluminum water jacket with O-ring seals was machined to fit around the mud cup of the Fann meter. All mud samples were prepared by thorough mixing in a Hobart mixer. Viscosity and gel strength measurements were made with the Fann meter using standard procedures. Flow properties of muds were studied at 80, 120, 160 and 180°F. The compositions of the test samples are given in Table 1. The typical effect of temperature on the flow properties of these drilling muds is illustrated by Fig. 1. It was found that plastic viscosity and apparent viscosity decreased with an increase of temperature. However, the curves were not linear, and did not appear to follow any definite trends or patterns. Yield point data showed much more scattering.' Since a usable method for predicting drilling mud flow behavior with temperature was desired, an attempt was made to find a simple relationship between these variables. The basic approach used by Havenaars for predicting the same effect on turbulent viscosity resulted in Fig. 2, which shows that

By P. H. Royster

On the Continent, ferromanganese has been produced in the blast furnace almost continuously since 1876, but little definite information concerning the practice is to be found in technical literature, and almost nothing in the way of a theory of the manganese furnace. In this country, prior to 1904, but one company had attempted its production in a serious way, and none of the operating data or other information from this company has been, or is, available to the public..In the last 5 years, as a result of the restriction of imports, a number of furnaces have been blown in on this alloy, with the result that in 1918 as many as 18 furnaces were in blast. The majority of the men in charge of these furnaces had had little previous experience in such operations; so the Bureau of Mines, in the summer of 1918, undertook the collection of data from ferromanganese furnaces. Operating data were collected by the Bureau from eleven ferromangahese furnaces, which will be referred to throughout this paper as furnaces A, B, C, F, G, I, J, K, L, M, and P; the dimensions of seven of the furnaces are given in Table 1. The companies from whom this information was obtained, and to whom should go the credit for whatever value this information may possess, are the Bethlehem Steel CO.,

Jan 1, 1920

By Hobart M. Kraner, E. B. Snyder

THIS paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, particularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercial blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. FACTORS AFFECTING CHOICE OF REFRACTORIES If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing temperature, which he in turn interprets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and resistance to the action of slag. In most refractory applications several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient stages and the progress is determined by measuring slight changes in. porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures . at which they are to be used, although in many cases it would be desirable from the user's point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. -Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By M. M. Singh, H. L. Hartman

This paper reports on the results of a fundamental investigation of the behavior of rock under impact of a chisel-shaped bit. Drop-tester studies were conducted with strain gauges attached to the rock and striking bit-edge. It was established that rock behaves viscoelastically. Little correlation was found to exist between the strain waveforms detected on the rock surface and in the bit; thus, strain-time curves obtained with transducers mounted on the bit cannot be used to explain the sequence of events in rock breakage. It is estimated that nearly 1 per cent of the total energy of the blow is expended in permanent deformation of the rock. The strain- energy distribution on a rock surface as a result of chisel impact, which follows a simple law, is presented graphically. Experiments also were conducted with gauges embedded in the rock vertically below the line of impact and at an angle of approximately 45' to the vertical. No essential difference was observed in the type of wave obtained with embedded gauges and with gauges on the surface, as may have been anticipated from theory. INTRODUCTION Through the ages great strides have been taken towards improvement of the various techniques applied in the breakage of rock. Indeed, numerous applications of the rock-failure process are an integral part of present-day industry, including oil well drilling. Yet, astonishingly, little is known regarding the behavior of rock under dynamic loading or the mechanism of rock failure. The value of impact loading studies from the point of view of drilling is evident, however, and requires little elaboration because impact of a chisel edge on rock forms the basic action constituting most common methods of drilling. RELATED STUDIES Impact studies of communition and fragmentation conducted by Fahrenwald, et a1,8 Poncelet,l7 Axelson, et a1,2 Piret,16 Hartman and pfleider,ll Charles and deBruyn,5 and others have been of considerable help in understanding rock-breakage phenomena. Further insight into the basic action of drilling and penetration has been obtained by the work of Irving,13 Cherkasov and Shlyapin,6 BOrcherdt,3 Shepherd,19 Shreiner and Pavlova,20 Drilling Research Inc.7 Hartman,10 Appl and Gatley1 and several other investigators. However, knowledge concerning the stresses and strains induced in the rock and bit during impact remains scant. Recent photoelastic studies by Tandanand and Hartman (1961. 1962)22, 23 have shed light on stress distributions and Fracturing produced in plastics by chisel-shaped bits. In the field of transient strain Pulses and their role in rock drilling, the only extensive work has been performed by Drilling Research Inc. (DRI). They attached strain gauges to the shank of a bit and conducted drop-tester studies, using a die-shaped bit to obtain force-time diagrams. Their work led to the conclusion that, for a given rock type, the first peak of force occurs at a fixed level regardless of the total energy in the system, provided it exceeds a certain minimum threshold level. Further, on this basis an explanation was offered for the sequence of events in crater formation as the result of a single blow on rock. PURPOSE OF PRESENT STUDY The investigations reported in this paper were conducted in a manner similar to the DRI approach, but with the objective of determining the strain distribution in the rock around the area of bit impact and, to a limited extent, the strain in the chisel-shaped bit itself. It was expected that a knowledge of the disposition of these strains, along with the rate of attenuation of strain energy in the rock

By R. B. Falk, F. E. Luborsky

Small iron particles in mercury pow by diffusion of iron atoms through the mercury. Iron particles, with diameters about 200Å, have been stopped from gvowing in size, even up to the boiling point of mercury, by the addition of a third metal. The metal additives were classified according to whether they produced 1) negligible inhibition, 2) some inhibition, or 3) marked inhibition of the growth rate. Metal additives which resulted in a marked inhibition of iron-particle growth form a stable monolayer on the iron particles. Only those metals which may form compounds with iron showed this pronounced effect. The one exception was manganese. Metal additives which resulted in no inhibition of growth, showed no evidence for adsorption and could not form compounds with iron. None of the added metals, even those which strongly inhibited particle gvowth and thus had adsorbed on the particle surface, actually formed any compounds with iron at room temperature at the concentrations required for complete inhibition of growth. ThE stabilization of the size and shape of metallic particles dispersed in liquid metals has important technological implications in "homogeneous" nuclear reactor systems and in elongated particle magnets and is directly related to the problem of corrosion by liquid metals. Growth in these par-ticulate systems may occur by diffusion of atoms from surfaces of high energy, corresponding to a small radius of curvature, to surfaces of low energy or large radius of curvature. Thus, small particles dissolve and large particles grow to increase the average diameter of the particles. reenwood' has analyzed this diffusional growth of a system of particles containing a distribution of sizes and has obtained reasonable agreement with data on the growth of uranium particles in liquid sodium and UPb3 particles in liquid lead. Greenwood concluded from his analysis that the chief factors promoting stability of dispersed particles growing by a diffusion mechanism are large mean radius, high density, and low molecular weight with low values of the solute diffusion coefficient, the solubility, and the interfacial tension. In the case of elongated particle magnets the system of interest is that of iron particles dis- persed in mercury. Previous work,2 concerned with "spherical" particles in mercury, has indicated a diffusional growth mechanism similar to that discussed by Greenwood. It has also been shown3'4 that the addition of certain metals to Fe-Hg dispersions results in the formation of a monatomic layer of adsorbed atoms on the iron particles. In this paper we will show that this adsorbed layer provides the decrease in the iron-atom flux through the mercury necessary for size stabilization. The general features of the stabilization of the iron particles in mercury through the formation of this "coating", with many different metals, will be described. EXPERIMENTAL RESULTS Iron particles in mercury were prepared by elec-trodeposition,2, 4 and measurements2, 4 of coercive force HCi) and saturation induction (Is) were used to follow changes in size and composition during thermal aging in the mercury in the presence of relatively small amounts of an added metal. In Fig. 1 is plotted the aging behavior of spherical particle samples in the presence of some of the added metals to be discussed. The iron particles have an initial average diameter of 180Å. Each sample was aged for 20 min at each temperature in succession in the presence of a twofold to threefold excess of added metal over that required to form a monolayer on the iron particles. These are the same samples used previously3 to study the adsorp-

Jan 1, 1965

By G. W. Binkley, G. K. Dumbauld, F. A. Brooks, B. E. Morgan

In recent years, oil well cementing compositions have been developed with low densities, controlled set strengths, and satisfactory thickening times. With the introduction of the permanent-type well completion method for cementing wells, another property—that of rate of filtration or water loss to permeable formations— has become important. Laboratory data show that cement slurries prepared with oil, water, bentonite, and calcium lignosulfonate possess satisfactory thickening times, strengths, and filtration properties for primary cementing of casing and for squeeze cementing with the permanent-type well completion technique. Cementing compositions have been prepared with oil-in-water emulsions varying in composition from 60 cc water and 20 cc oil per 100 gm cement to 90 cc water and 45 cc oil per 100 gm cement. These compositions have contained from 0.4 to 5.0 per cent calcium lignosulfonate by weight of dry cement. Slurries prepared from these compositions weigh 11.4 to 13.1 lb/ga1 and have filtration rates of from 10 cc to approximately 100 cc in 30-min API tests at room temperature. The unfiltered emulsion cements develop one-day tensile strengths of 60 to 220 psi; and the filtered mass sets to tensile strengths of 60 to 150 psi in 12 hours and develops strengths of 320 to 515 psi in seven days when cured at 125° F. Field experience gained from 13 field mixing jobs demonstrates the utility of the emulsion cement for permanent-type squeeze cementing operations. INTRODUCTION In recent years, research in oil well cementing composition has been directed toward the development of cements having low densities, controlled set strengths, satisfactory thickening times, and low rates of water loss by filtration. Two well cementing compositions that have been developed with these properties are the modified cements containing, respectively, 12 and 25 per cent bentonite clay and various concentrations of calcium lignosulfonate1,2 In a search for other ways to incorporate these characteristics in a cementing composition, consideration was given to the rheological properties of oil-emulsion drilling fluids. Many of the desirable properties observed in oil-emulsion drilling fluids are equally advantageous in a cementing composition. For example, low water loss by filtration and low density, which are inherent characteristics of these oil-in-water emulsions, are desirable for many oil well cementing operations. Furthermore, oil-emulsion slurries have lubricating properties similar to those of oil-emulsion muds, a factor which should provide ease of rotation of casing during primary cementing operations. The properties of lubrication and low filtration may be of special value in both primary and squeeze cementing operations encountered in slim-hole drilling. Studies in the preparation of oil emulsion systems have pointed out the need for violent agitation in order to disperse the oil into the water phase. It was thought, therefore,

Jan 1, 1957

By Basil Prescott

Resume.-The district of Santa Eulalia lies 12 miles to the southeast of the city of Chihuahua, Mexico. The ore deposits occur in a Cretaceous limestone of unknown thickness, overlain by a series of rhyolitic tuffs and flows. The limestone is very gently folded and is cut by several systems of fissures, of which only those with a general north-south strike are pre¬mineral and control the deposition. The deposits are of two main types; the earlier silver-bearing iron sulphide types occurs as high-grade tabular bodies resembling veins and as large masses of relatively low-grade ore. The gangue of this type is composed of lime-iron silicates that point toward a close association with an igneous rock mass which has not yet been encountered. In the later silver-lead-zinc type the ore occurs in vertical chimneys and horizontal mantas, principally as oxides, though at a depth of 1,500 ft. some sulphides have been encountered. During oxidation the ore chambers have increased in size owing to the solution of the walls by the sulphuric acid generated in the process, and a substitution has taken place of nearly one-half part by weight of the original constituents of the ore, by newly introduced elements and radicals. Both types are believed to have come from greater depths than those yet reached by mining, and their ultimate source, from a consideration of similar deposits, is believed to be an igneous rock in contact with the limestone at some horizon below. The deposits are believed to have been formed at unusually great depths, as indicated by the proved great vertical range of the silicate minerals coupled with the absence of the igneous rock, and by the practically unchanged character of the silver-lead-zinc ores as far as developed. The volcanic capping is believed to be distinctly later than the economically important ore deposition.

Jan 2, 1915

By M. Takeda, H. Majima

Pyrite has been subjected to xanthate adsorption experiments in order to determine the nature of adsorption. The identification of adsorbed species by means of IR spectroscopy, as well as UV, shows that the dixanthogen adsorption is undoubtedly predominant on pyrite surface. The rest potential measured in a xanthate solution coincides with the redox potential of the xanthate-dixanthogen couple. Considering all the factors together, the adsorption mechanism of dixanthogen on pyrite has been proposed as This mechanism is consistent with the "passive" character of pyrite. From the measurement of the redox potential of the xanthate-dixanthogen couple in the homologous series, a rule similar to that for surface tensions proposed by Traube is also applicable. The polarization experiments were conducted on pyrite in a solution containing xanthate. In the anodic polarization, xanthate is observed to oxidize to dix- anthogen, which depresses oxygen evolution on py rite at higher potential levels. In spite of the importance of the presence of pyrite in the flotation of sulfide minerals, not many studies have been made on the xanthate-pyrite system in the absence of an activator or a depressant. In an early study by Gaudin and Wilkinson,' it was pointed out that no ferric xanthate was formed on a pyrite surface, while in another study Gaudin and his collaborators2 proved the formation of a very small amount of ferric xanthate. Afterwards, Gaudin et al.3 studied the pyrite-xanthate system with a radiometric technique and found indications of the presence of adsorbed dixanthogen on pyrite surfaces. Mamiya4 studied the flotation behavior of the pyrite-xanthate system and also suggested the possibility of dixanthogen. Recently, Fuerstenau and his coworkers at The Colorado School of Mines5 studied the role of dixanthogen in the xanthate flotation of pyrite and discussed the problem in terms of such properties as oxidation potential, zeta potential, flotation recovery, pH of solution, etc. However, the mechanism of dixanthogen adsorption at the pyrite-water interface is not yet understood. This paper is concerned with an electrochemical in-vestigation through which the mechanism of dixanthogen adsorption on pyrite is interpreted. EXPERIMENTAL MATERIALS AND TECHNIQUES Pure potassium xanthates were synthesized by an

Jan 1, 1969

By H. H. Uhlig

Soon after general use of stainless steels began, it was observed in practice that certain combinations of factors tended to induce corrosion by pitting. For most applications this was a serious drawback, not so much because the structural properties of the metal were impaired but because of the rapidity with which heavy sections of the alloys were penetrated by small elongated pits. These pits seemed to initiate readily in oxidizing metal salt solutions like ferric chloride and in chloride solu-tions like sea water. It was observed that in sea water pitting was more frequent in stagnant or polluted waters than in highly aerated, moving waters. The steels in these chloride solutions were observed to be sensi-tive to long contact with material such as sand grains or attached bar-nacles. At points of attachment or contact it was not uncommon to discover initiation of corrosion. Pits once begun at contact faces were observed to grow rapidly, usually elongating phenomenally in the direc-tion of gravity until the metal was perforated. Hydrochloric acid and other nonoxidizing acids, on the other hand, were observed to corrode stainless steels generally; the weight losses often were higher, but the penetration less than for the pitting type of corrosion. The causes of pitting, a type of corrosion recognized as character-istic not only of stainless steels but of many additional metals and alloys, are important in corrosion studies. A possible explanation bears prac-tical significance, for once it is known why pits begin where they do and continue to grow after initiation, intelligent direction can be given to diminishing corrosion. This can be done either by some alteration in the composition and treatment of the alloy or by some alteration in the environment. It appears foremost in importance to discover the nature of pit foci, for if initiation of pits can be discouraged their growth will be no longer a factor to be considered. In a multi-component alloy containing many impurities normal to production of such an alloy, each of which may play a part in pitting, and whose corrosion resistance is sensitive to heat-

Jan 1, 1940

By H. V. Welch

In this paper, as prepared for delivery at the Southern California regional meeting on Oct. 14, 1948, it was thought best to interpret the term "economics" in a rather broad manner and to include, in addition to the material losses and recoveries and associated monetary values (Part I), a limited discussion of the increased difficulties or the particular problem and the special requirements, as the particle sizes of the suspended particles range down from the relatively coarse to 100, to 10, to 1 micron or even to a fraction of one micron (Part II). Further, it is not quite in order to overlook entirely the community and individual health problems, although space requires the economics of this to be considered only very incompletely. Therefore, Part III, covering this phase of the subject, is very limited. This paper, then, is divided into 5 parts or headings as follows: I Losses and/or values in suspended solids. II Particle size. III Dust and fumes in community and individual living. IV Means and Procedures for dust and fume collection. V Description or examples of specific equipment in service and of the several types used for dust and fume collection. Because of the wide extent and wealth of subject material available and the space and time limitation imposed, presentation and discussion are less than originally planned. I—Losses and/or Values in Suspended Solids The weight involved in moving streams of industrial plant gases is commonly not appreciated, neither is their carrying power in the weight of solids maintained in suspension and moved with the gas stream from a point of origin or pick-up to a point of dissipation or settlement. These, however, are major weight figures; for example, in a modern iron blast furnace there may be five tons of gas for every ton of iron produced and by the time this blast furnace gas has been burned in stoves or under boilers the weight of gas discharged to atmosphere is on the order of eight times the weight of iron produced. Similarly for nonferrous metallurgy there may readily be from 10 to 20 times the weight of gases discharged to atmosphere as there is metal produced. A cement kiln in operation or a kiln in service to produce metallurgical lime may have on the order of 5 to 6 times the weight of stack gases as of clinker or lime produced, and at least the cement kiln, because of the very fine nature of its feed, is a very heavy dust producer. It may be noted that there have been two developments in progress for nearly three decades. Both are extraordinary in the industrial economics effected and in their ready availability to ever larger units of operation and their ever widening importance in industry, and both are productive of great quantities of finely divided material in furnacing. The first of these is the flotation process for ores, especially the metallics such as copper, lead, and zinc; and the second, powdered fuel combustion for power plant, industrial plants and metallurgical operations. Today, new developments, for example, flotation for the nonmetallics such as higher grade limestone for cement manufacture which requires still finer grinding and the powdered-coal-fired boilers with production ratings of over 1,000,000 lb of steam per hr, bring still more concentrated and hugely increased quantities of stack emission. Perhaps the honors for the greatest interest in the quantities and values escaping in waste furnace and equipment gases belong to the nonferrous metallurgical operations. Their record of achievement in the installation of dust and fume collection equipment, largely baghouses or Cottrell electrical precipitators, is exceeded by no other industry. Something of the magnitude and variety of equipment utilized in such recovery systems was covered by the writer in two papers presented to the Institute some 10 years ago.1,2 It is not intended to repeat the material of those articles, but it is thought that they complement this offering and should be noted. COPPER ROASTERS As the copper roasters are the first of the series of furnaces handling the copper-bearing concentrates in the usual copper smelter of today, it is in order to make them the first consideration. Multiple hearth sulphide roasters, not hard driven, often maintain their dust loss through exit gases at 3 pet or below of feed to furnace; in hard-driven or maximum-driven furnaces, exit gas losses often approximate 7 pet of charge with a ±2 pet variation for special conditions prevailing at some plants. A 5 pet loss of feed in a roaster gas exit, unless reclaimed, often makes the difference between a profit and loss operation, and in many cases substantial recovery is the very basis of dividend payments. As there is available very practical and successful equipment for the collection of the

Jan 1, 1950

By R. L. Bleifuss

Most pellets swell only slightly during reduction, but some swell so enormusly that their increase in size is termed catastrophic. Since catastrophic swelling produces irregularities in blast furnace operation, an understanding of the phenomenon is of practical as well as theoretical interest. Observations have shown that catastrophic swelling is characterized by the growth of a network of fine iron filaments. Evidence is presented to show that the growth of these filaments is promoted by the presence of calcium in the magnetite lattice of the original ore. During reduction, the limited mutual solubility of CaO and FeO produces an unstable condition that inhibits the uniform nucleation of metallic iron. Other elements in the magnetite lattice whose oxides are continuously soluble in FeO in the critical temperature range have no effect. Magmatic segregation or pyrometasomatic replacements are the most likely deposits to contain calciferous magnetite. Over the past few years there has been an increasing concern throughout the iron and steel industry over the tendency of pellets to swell during reduction. Although the tendency for swelling is only one of several attributes that determine the behavior of pellets in the blast furnace, swelling-reduction tests are now part of the normal evaluation procedure of many pellet consumers. During a swelling-reduction test, pellets display either the moderate increase in size known as normal swelling, or the enormous expansion known as catastrophic swelling. This paper is concerned with the origin and control of catastrophic swelling and how it is enhanced or inhibited by the presence of minor elements. Swelling Behavior The swelling behavior of pellets during reduction is indicated in Fig. 1. The lower curve represents normal swelling and the upper curve catastrophic swelling.' During the initial stages of reduction, that is, up to about 20-25% reduction, the two curves are considered to be equivalent. Beyond this point normal pellets undergo a gradual decrease in size with increased reduction. By contrast, pellets which exhibit catastrophic swelling show a second dramatic expansion between 25 and 70% reduction. The initial normal swelling develops as the hematite of the pellet is successively reduced to magnetite, and then to wustite. Work by Edstrom' and others has shown that the reduction of hematite to magnetite is accompanied by a 25% volume increase, whereas the magnetite to wustite stage shows a volume decrease. The volume increase overlaps the wustite field because magnetite is formed simultaneously with the wustite during topochemical reduction of the pellet. The catastrophic expansion is clearly related to the wustite, to

Jan 1, 1971