Search Documents

Minnesota School of Mines Experiment Station, University of Minnesota, Minneapolis, Minn For copies of Bulletins or a list of publications, address The Director Bulletins available are Bulletin 1, Iron mining in Minnesota, by C. E Van Barneveld (1912), $1, 2, Concentration tests on Mesabi ores, by W R Appleby and E Newton (1913), 3, Preliminary concentration tests on Cuyuna ores, by W. R Appleby and E Newton (1915), 4, Bibliography of Minnesota mining and geology, by W. Gregory (1915); 5, Manganiferous iron ores of the Cuyuna district, by E Newton (1918), 7, The future of the Lake Superior district as iron-ore producer, by E W. Davis (1920), 9, Magnetic concentra¬tion of iron ore, by E. W Davis (1921); 10, Ball mill crushing iii closed circuit with screens, by E W Davis (1925); 12, Minnesota manganiferous iron ore in relation to the iron and steel industry, by T L Joseph and S P Kinney (1927). A mining directory of Minnesota, by J J Craig, is published annually.

Jan 1, 1933

By R. D. Fisher, A. G. Metcalfe, F. A. Crossley

AN investigation of the application of magnetic stirring to the consumable arc melting of aluminum and nickel demonstrated that grain refinement could be obtained when there was sufficient stirring force. Also, it was found that grain refinement could be obtained in aluminum by alternately reversing the polarity of the current through the magnetic stirring coil. The effect of the latter was to periodically reverse the direction of rotation of the molten metal.' Because of their promise, these findings were applied to conventionally cast aluminum. Shortly after this work was begun, Kondic2 reported experiments in which aluminum cast with 40° C (72° F) of superheat exhibited a grain size of 10 to 20 grains per cm2. When interrupted rotation was applied during solidification by mechanical means, a grain size of 800 to 1000 grains per cm2 was obtained. Magnetic Stirring Applied to Conventional Casting— The applicability of magnetic stirring to producing grain refinement in conventionally cast metal was evaluated in the following way. Three pounds of aluminum were cast into a clay-bonded graphite mold. The mold was surrounded by a magnetic stirring coil of 1000 turns. A direct current of 200 amp was passed through the casting by means of a graphite electrode which was immersed from the top. A current of 5 amp was passed through the stirring coil. The aluminum (1100 or 25) was superheated to 1600° F (871° C) and fluxed by passing chlorine gas through the melt for 2 min prior to casting. Two additional castings were made for comparison: 1) a conventional casting of metal superheated to 1600° F and 2) a similar casting through which 200-amp current was passed during solidification, but without current in the magnetic coil. Macrosections of these three ingots are shown in Fig. 1. Very remarkable grain refinement resulted in the magnetically stirred casting. It may be noted that the casting through which 200-amp current was passed has a coarser structure than the conventional casting. It would appear that this is due to the additional heat input generated by the current to the former casting. Mechanical Rotation Applied to Conventional Casting—A casting temperature of 1600° F was used throughout. Some 1 1/2 -lb castings rotated at 150 rpm were predominantly columnar with small areas of coarse, equiaxed grains close to the lower mold wall. Following these, a series of 3-lb castings was made. Macrosections of these ingots are shown in Fig. 2. The imposed rotational speed was 250 rpm. Turbulence or acceleration in the solidifying liquid was the significant factor. Fine grain size resulted in the material solidified during the period of acceleration of the liquid to the imposed rotational speed. When uniform rotational motion was achieved, the grain structure reverted to columnar. The final casting shown in the lower right-

Jan 1, 1962

Detailed Geology of Certain Areas in the Mineral Hill and Warm Springs Mining District. By A. L. Anderson. T. H. Kilsgaard and V. C. Fryklund. Jr. Idaho Bureau of Mines and Geology. University of Idaho. 73 P. Maps, Illus.-Divided into three parts, this pamphlet covers the geology and ore deposits of the Hailey-Bellevue Mineral Belt, the Triumph-Parker mine mineral belt, and the ore deposits of the Mayflower Area. Numerous maps and illustrations are included for each area. Government Administration of the Copper Industry, World War 11. By John W. Douglas. 1950.51 P. $1.-This pamphlet covers in detail all the steps relating to control and operation of copper and copper products, and is of particular interest to primary producers, brass mills, wire mills, and foundries. Of particular current interest is the booklet's coverage of the steps leading to the Controlled Material Plan, into which industry is now once again heading. Copies can be obtained for $1 from John W. Douglas, Republic Foil & Metal Mills Inc., 55 Triangle St., Danbury, Conn.

Jan 12, 1951

By Thomas MacFarlane

IN smelting copper, lead, and silver ores, it is scarcely possible in every case to make analyses of the various parcels of ore, with the view of combining these and the fluxes so accurately as to yield, in the furnace, slags of exactly the most favorable composition. This is even more difficult with ores which require previous calcination, or with mattes which have been roasted in heaps. Even in cases where the greatest pains have been taken and the most elaborate calculations made beforehand, it frequently happens that variations in the working of the furnace interfere with the result so much desired. Generally, the practical metallurgist must be content with ascertaining the average composition of his ores and fluxes, making a calculation once for all as to the most advantageous mixture, and leaving slight changes in its composition to be taken care of as it is passing through the furnace. The various products then afford him the best material whereon to base his judgment as to the manner in which his smelting mixture is working. Of course the character of the slag is one of his chief guides, but it is not always possible from its outward characters alone to form a correct judgment as to its composition. Neither would it be possible or practicable to apply chemical analysis for this purpose, as it would be impossible to wait for its results while working a furnace. Abich was, I believe, the first to point out the relation existing between the composition of volcanic rocks and their densities, and to show that, the latter being ascertained, very correct conclusions

Jan 1, 1880

By William P. Blake

THE use of diamonds upon a large scale in drilling rocks, and the substitution to a certain degree of rotary diamond drills for the ordinary steel percussion drills, marks a new era in the art of mining. Since the invention by Leschot of the diamond drill, it has steadily advanced in its utility and range of application, and in the appreciation of miners and engineers. I t must be claimed as one of the many gifts of science to the arts ; and it is, in particular, one of the fruits of the scientific education given at the Ecole Centrale, at Paris. Members are all, doubtless, more or less familiar with the construction of the drill and of the machinery by which it is applied in boring. I t is, therefore, my present purpose only to direct your attention to some recent marked improvements, made by the American Diamond Drill Company, by which the economy and efficiency of the machines have been increased. Form of Bit.-The annular or ring form of the drill-head or bit was, I believe, the earliest; and it is still in use, without essential modification, wherever it is desired to obtain a sample " core" or specimen of the rock traversed. But for mere drilling, regardless ~f the preservation of a test-core, a solid-head bit is preferred, except for very large holes. Until recently, these solid-head bits were made with a pointed cutting face shaped like an obtuse cone. This form was assumed to be the best, being most in accordance with the experience obtained with percussion drills. I t is found, however, that the exact reverse

By ERNEST A. HERSAY

ACCURATE ore-sizing with screens is drawing attention to certain details that now, more than ever before, require attention. There are many tests that must be preceded by careful sizing. The assayer often could profit by a more careful selection of screens. In milling, more attention is given the slimes produced. Cement-manufacturers are pulverizing and screening finer than they formerly did, and others are reducing materials to fine sizes at high cost, with screens used to govern the fine¬ness of the pulverized product. Fine screens are expensive, easily injured by mis-use, are carried in stock sparingly by most dealers, and are handled often by those who know little about them except their designated number. More attention, on the whole, needs be given the actual size of the mesh-openings, and less emphasis placed upon any custom or conventionality in numbering. An effort to classify wire screens, in this respect, leads at once into computations, where one is confronted with details of sizes and standards, of different wires, different gauges, and different customs. There is always uncertainty about the exact working-size of a screen until one gives the matter special attention, and devotes more time to it than its simplicity seems to demand. To know only the number is not sufficient for all uses. Often, in sets, superfluous sizes are used; and sizes are omitted that are of critical importance. In wire screens, the use of different standard sizes of wire makes important differences in dimensions that must be taken into account. The dealer usually grades screens by the number of openings per linear dimensions, regardless of the size of the openings or of the wire. Certain 100-mesh screens in use are found, by measurement, to he actually coarser than others of 90-mesh, a result which is due, of course, to the use of larger

May 1, 1906

By Thomas MacFarlane

In smelting copper, lead, and silver ores, it is scarcely possible in every case to make analyses of the various parcels of ore, with the view of combining these and the fluxes so accurately as to yield, in the furnace, slags of exactly the most favorable composition. This is even more difficult with ores which require previous calcination, or with mattes which have been roasted in heaps. Even in cases where the greatest pains have been taken and the most elaborate calculations made beforehand, it frequently happens that variations in the working of the furnace interfere with the result so much desired. Generally, the practical metallurgist must be content with ascertaining the average composition of his ores and fluxes, making a calculation once for all as to the most advantageous mixture, and leaving slight changes in its composition to be taken care of as it is passing through the furnace. The various products then afford him the best material whereon to base his judgment as to the manner in which his smelting mixture is working. Of course the character of the slag is one of his chief guides, but it is not always possible from its outward characters alone to form a correct judgment as to its composition. Neither would it be possible or practicable to apply chemical analysis for this purpose, as it would be impossible to wait for its results while working a furnace. Abich was, I believe, the first to point out the relation existing between the composition of volcanic rocks and their densities, and to show that, the latter being ascertained, very correct conclusions

Jan 1, 1880

By Thomas T. Read

THE benefits derived from stabilization of industry that might possibly be attained through some scheme of centralized economic planning have been much discussed of recent months, and opinions on the subject range from those who believe that some agency like the War Industries Board would be practicable to create and wholly beneficial in effects, to those who are equally convinced that none of the suggestions so far advanced are at all practicable, or likely to be productive of more of good than of evil. The discussion has been on the general topic, but-many of those who have written or spoken on it have introduced economic problems of the pinera1 industry; for example, Newton D. Baker, who referred to the coal industry in his address on economic planning at the Williamstown Institute of Politics on July 31, and then went on to say, "Industrial progress is made by the development of new things, but new things upset the equilibrium of any plan. Who could have planned the industrial effects of the development of the railroads, or the economic changes which you have seen attend the development of the internal combustion engine. Obviously, unless we are prepared to put world economics in a strait-jacket and, like the encyclopedists, write its full history on the theory that further progress is impossible, no such plan could be made for nations which are forging ahead as is entirely rational for nations which are still catching up."

Jan 1, 1931

By L. D. Jaffe

IT is now well established that quenched and tempered titanium alloys have much better ductility when the quenching is from a two phase a-B structure, rather than from an all B structure. The corresponding microstructural differences, however, have not been shown in previous publications. Accordingly, specimens were cut from a % in. rod of commercial RC-130A, containing 7.9 pct Mn and 0.12 pct C, which had been previously hot rolled, heated 1 hr at 1100°F, and air cooled. (The same heat has been studied by others." 7 Samples about 1/4 in. cube were heated in helium 1/2 hr at 1450' or 1700°F, quenched in brine, tempered in helium 1 hr at various temperatures up to 1250°F, and quenched in brine. They were then sectioned and metallo-graphically examined, using an etchant of HF-HNO, in glycerine. As quenched from 1700°F, the microstructure observed was clear /3. (Probably also present was U, as the hardness was 400 Vhn, but w is not yet reliably revealed by any metallographic technique.) When the /3 quenched alloy was tempered at a high temperature, a precipitated as a grain boundary film

Jan 1, 1957

By R. N. Bhattacharyya

In recent years, increased attention is being paid to the application of oil-agglomeration technique for (a) improved recovery of low- ash clean coal, (b) effective beneficiation of low-grade coking coals and (c) removal of pyrite sulphur from high-sulphur coals. In this technique, which has been proved to be more effective than convention- al froth-flotation, advantage is taken of the oleo-philic nature of finely ground coal to separate it under controlled conditions from the associated minerals which are hydrophilic in nature. Unlike froth- flotation, no aeration is needed in the process and the concentrates which are obtained in the form of agglomerates or micro-pellets have easier dewatering characteristics. Optimization of operating variables in treating individual raw feed is a pre-requisite for the successful application of this process. A 10 gram batch unit was employed in the present test series. This paper presents - results from these investigations on such operating variables as (i) size of coal, (ii) amount of oil used, (iii) time of stirring, (iv) rate of stirring, (v) solid content in slurry and (vi) effect of conditioning.

Jan 1, 1977

By R. D. Springer, R. L. Wilcox, P. A. PALMARTAN, R. K. Waring, E. A. Anderson

A knowledge of the mutual liquid solubility of zinc and lead is of importance in various phases of zinc metallurgy. The determination of this solubility has been the subject of numerous investigations, but unfortunately the results vary widely, particularly at higher temperatures, and it has been impossible to decide what data are most reliable. It was decided to investigate the matter and in view of the disagreement in the published results, it was felt necessary to take rather unusual precautions to insure the reliability of the data. For this reason determinations were made by four different methods, and the procedures of several of the previous investigators were duplicated. The previously used methods can be divided into two classes: methods involving freezing the entire melt and taking samples of the lead-rich and zine-rich phases in the solid state,l,2 and methods in which the samples are taken while the bath is liquid and at the desired temperature.3,4 Data obtained by methods involving freezing the entire melt show much lower solubility of lead in zinc than methods in which the liquid is sampled at temperature. The latter method was used by Spring and Romanoff5 and by Hass and Jellinek.6 The results of these two investigations are in agreement at temperatures near the melting point but at higher temperatures Hass and Jellinek find a higher mutual solubility. The low-temperature section of the zinc-lead equilibrium diagram is given by Peirce and Anderson.7 The diagram is based on the data of Hodge and Heyer,8 Arnemann,9 and Peirce.10

Jan 1, 1934

By Chikaosa Tanimoto

INTRODUCTION The committee on Rock Mechanics, Japanese Society for Civil Engineers, has been discussing 'soft rock engineering in Japan' and presented several papers concerning dam, tunnel, bridge and slope constructions to International Symposium on Weak Rock, Tokyo 1981. This is the summarized paper based on References of Okamoto et a1 (1981), Iida et a1 (1981), Working Group on Tunneling-JSCE (1981), Working Group on Bridge Foundations-JSCE (1951) and Kikuchi et a1 (1981), which can convey general view on engineering experiences with weak rocks in Japan. From the point of view to the origin and/or distinctive physical properties, weak rocks in Japan may be classified into (1) sedimentary, (2) weathered, (3) low welded-pyroclastic and (4) fractured ones. Their typical characteristics are summarized in the following section. Concerning dam foundations on soft rock, several hundreds have already been constructed and, at present, nearly one hundred are under construction or at planning stage. These dams, almost without exception, have some problems such as site selection, material selection for fill-type and concrete dams, design of dam and its foundation, and construction procedures, requiring special ingeneous and cautious measures to cope with the local geotechnical difficult situations. In tunneling, for the decade of 1970s, the number of tunnels in soft rock either completed or under construction was at least 160, including Seikan Tunnel of 53.9 km long, Nakayama Tunnel of 14.8 km long and so on. Most of these tunnels are distributed in the northern half of Mainland, consisting of a basement of Paleozoic strata and Plutonic rocks, overlayed by Neogene Tertiary formations which include large

Jan 1, 1982

By F. F. Poland

The purpose of this paper is to describe the recent applications and improvements made in the process and equipment for the recovery of metallic zinc from secondary metals by means of high temperature electric resistor furnace distillation. The process and high temperature furnace, as developed by Revere Copper and Brass Incorporated, Research and Development Department, was described in a previous paper. † Since the publication of that paper the process and equipment have been licensed to others. Consequently its field of application has been expanded, particularly for the treatment of scrap brass, galvanizers dross and scrap zinc. Other applications are being considered, particularly the melting of metallic titanium and special alloys requiring a controlled atmosphere. Consideration is also being given to modification in design that would allow the melting of copper cathodes for the production of oxygen-free and electrolytic tough pitch copper shapes without the necessity of blowing and poling. In the design of a furnace for melting copper cathodes it is intended that the fundamental principle of charging the solid material into a large pool of molten metal through a double door charging vestibule as shown in Fig 3 of the previous paper, † would be adhered to and, in addition, either dehydrated and desulphurized producer gas or commercial nitrogen, that is, approximately 96 pct nitrogen, 2 pct hydrogen 2 pct CO, also dehydrated, would be used to provide a protective atmosphere for the resistors and to flush out more soluble gases from the molten copper. The operation of a small unit producing approximately 1000 lb of copper per hr has shown that the commercial nitrogen will allow the production of tough pitch electrolytic copper when the metal is transferred from the meltdown unit contemplated to a special type induction unit where the oxygen absorption and temperature can be controlled. Standard practice in treating low grade scrap brass has been to oxidize the zinc by blowing air through the molten metal. This operation results in the recovery of approximately two-thirds or less of the zinc content of the brass in the form of an impure zinc oxide having only a fraction of the value of the zinc in metallic form. The balance of the zinc is lost to slag, fume and drosses. Fig 1 shows the revised flow sheet of the process for the treatment of scrap brass. For this application and as shown on the flow sheet a low frequency induction furnace has been substituted for the Wilkins-Poland type as a melting unit. This type of furnace has been found the most suitable for the purpose as will be shown by the following discussion. Serap Brass The melting of refinery scrap brass preparatory to distillation presents a melting problem quite different from the usual melting of brass mill scrap for recasting because refinery scrap is a heterogeneous mixture of alloys each having different melting and boiling points, and coated with a variety of corrosion products and foreign materials. In addition, brass and copper plated pieces of sheet iron, stainless steel, ceramic materials, and others are present that do not melt except at temperatures above the boiling point of the liquid bath. In the previous paper it is noted that difficulty was encountered in the melting of refinery grade scrap brass without excessive loss of zinc by volatilization and that 5 to 10 pct razorite flux was used to alleviate this condition. While this flux was successful in preventing the excessive loss of zinc by volatilization it interposed a low heat conductivity layer between the source of heat and liquid charge and resulted in lowering the melting rate of the furnace. This same problem presents itself in all types of furnaces in which the metal is heated by radiation and conduction from above the charge. It has been found in melting this type material that the melting rate per hour or per square foot of hearth area

Jan 1, 1950

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment, these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In U.S. Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center's 900-lb per hr pilot plant, approximately 85% of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to 51000 ppm equivalent SiO*, while maintaining a Ca(II) content of =16 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water. Water quality is perhaps as important to flotation as are the reagents used. The character of water is extremely variable, depending on whether the source is a well, lake, or stream, upon the season and temperature, upon prior use, and upon the character of the watershed. All of these factors influence the water hardness and the quantity of other dissolved inorganic salts, turbidity, dissolved and suspended organic matter, dissolved gases, and pH. Frequently, the differences in water quality can measurably influence flotation selectivity, often to the point of spelling success or failure. Water hardness is particularly troublesome in flotation systems employing fatty acids, but other unrecognized constituents may also contribute to peculiarities in flotation behavior. Furthermore, a given water source may be entirely satisfactory in one flotation system, but entirely inappropriate in another. In recent years, society has given more attention than formerly to water use, even in areas where water is plentiful. However, both the demands of a growing population, with increased per capita needs, and also those of industry must be met. As a result, riparian rights must be negotiated with the appropriate government agency or agencies so that consumption of water is often allocated or otherwise controlled. Furthermore, the disposal of off-process industrial and domestic water is coming under the increasing scrutiny of these same governmental units. In these respects, the mineral industry is no exception, so that conservation, water reclamation, and reuse may be expected to assume increasing importance. In 1932, it was stated that, "water reclamation is generally more expensive than the economy in water and reagents resulting from its use. It is employed only if it is urgent to save water."' The economic aspects of this statement may still be true, but the unrestricted use of water is becoming less and less an option of the user. The purpose of this paper is to discuss an investigation conducted by the U.S. Bureau of Mines (USBM), in which water reclamation and treatment were undertaken to develop procedures for, and to assess the effects of, water reuse on the flotation treatment of nonmagnetic taconites. This investigation is a logical extension of previous work described by the author and associates at the Twin Cities Metallurgy Research Center employing selective flocculation-desliming and anionic flotation of silica from low-grade, nonmagnetic iron ores2,8 The requirements for the selective flocculation-de-sliming and the anionic flotation of silica processes determined the direction of the investigation. Previous studies had indicated that pH levels of about 11.0 and 11.8 were required for selective flocculation and flota-tlon, respectively. The calcium content of the water was believed to be of importance in both of these operations, and since Minneapolis tap water with a Ca(I1) content of about 16 ppm had been successfully used, an attempt was made to reclaim the process water at an equal level of dissolved calcium. Additionally, the objective was to nullify or effectively limit the effects of dispersants and fatty acid residuals from prior stages of processing. Last but not least, the system of water treatment had to have the capability of reducing turbidities to workable levels. With about half of the effluent being derived from the selective flocculation-desliming step and carrying about 25,000 ppm of highly dispersed, suspended fines, this last objective appeared formidable at the outset. Procedures for water reclamation were derived, in part, from well-known mineral dressing practices, from past observations and investigations, and from concepts contained in various pertinent publications on water treatment."c These procedures involved: 1) flocculation with lime and poly electrolyte-type flocculants, 2) lime-soda-ash softening, 3) chemical precipitation, and 4) mineral surface adsorption. Control was exercised at various stages of water reclamation by frequent measurements of Ca(11), pH, and turbidity.

Jan 1, 1971

By R. S. Busk

TWO groups of binary alloys were prepared. The first group consisted of those elements relatively soluble in magnesium: Li, Al, Zn, Ga, Ag, Cd, In, Sn, Hg, T1, Pb, and Bi. These are predominately Group B elements. The second group consisted of most of the remaining metallic elements, all of which are relatively insoluble in magnesium: As, Au, Ba, Ca, Ce, Cu, Ir, La, Mn, Ni, Pd, Pt, Rh, Sb, Si, Te, Ti, W, and Zr. These are all Group A, transition, or rare earth elements. Alloys of the first group were prepared by melting sublimed magnesium and elements as pure as obtainable in a graphite crucible, using a standard flux1 for protection. The melts were poured into a small graphite mold to produce 3xY4 in. diam slugs. Spectroscopic analyses were made of each slug. In all cases, the total impurity content was less than 0.05 pct. The slugs were then heat treated 5°C below the eutectic temperature until complete solution, as judged metallographically, was obtained. Filings from the center of the slugs were compacted at room temperature into 1/2 in. long x 1/4 in. diam cylinders, sealed in pyrex under 1/2 atm of purified argon, annealed at the heat-treating temperature for 1 hr, and quenched in water. After the X-ray diffraction patterns were made, each compact was analyzed chemically for the solute. It was found that the Mg-Li alloys reacted during filing to reduce the Li in solid solution. For this series of alloys, the slug was cold worked, annealed in purified argon, the surface dissolved in dilute HC1 to a depth of about 0.005 in., and the X-ray exposure made on the fresh surface. This procedure resulted in sharp, continuous lines and in true values for the lattice parameters. The alloys in the second group were prepared in the same way except that about 1 wt pct of each solute was added. Since the solubility limit was exceeded, not all the solute dissolved. These alloys were analyzed spectroscopically only to confirm the presence of the solute. The diffraction patterns were of the back-reflec-tion type using the characteristic copper radiation* and a flat cassette. Both the film and the specimen were rotated. The specimen temperature was maintained at 25" ± 1°C. The films had sharp lines; their diameters were measured directly to 0.01 cm. The parameters were calculated from the line diameters using a modified version of Cohen's extrapolation method.2 his method effectively eliminates systematic errors such as film shrinkage, inaccurate alignment, and non-precise film-to-speci-men distance. The random errors were minimized

Jan 1, 1951

By Murray F. Hawkins, W. J. Ainsworth

In all types of subsurface pressure gauges the extension which occurs in the pressure-sensitive element is a function of the difference between the external (well or calibration) pressure and the internal pressure within the gauge, rather than a function of the external pressure only. The internal pressure is near atmospheric and depends upon (a) the quantity of air sealed within the gauge at the time of calibration or measurement, (b) the quantity of moisture (liquid water), if any, sealed within the gauge, and (c) the temperature at which the calibration or well measurement is made. Part of this correction for the change of internal pressure with temperature is taken care of by the customary temperature coefficient of the gauge. However, part of it is not, and while this portion may be only a few psi, it is nevertheless predictable or preventable, and should be considered in precision measurements. ERROR NO. 1 If air is sealed in the gauge at the same temperature and pressure for both the calibration and the well measurements, the usual temperature correction will take care of any difference between calibration and well measurement temperatures. However, if air is sealed within the gauge at temperature T1 and pressure P1 at calibration but at temperature T2 and pressure P2 for a well measurement, because different amounts of air are sealed within the gauge in each case, the internal pressure at. or corrected to, calibration temperature Tr will he different by where all temperatures and pressures are absolute. The calibration temperature is used, and not the well measurement temperature, because the usual temperature correction reduces the well measurements to calibration temperature. The correction term as calculated by the above equation is separate from. and in addition to, the usual temperature correction. Example: T, = 540°R, sealing temperature at calibration P, = 14.7 psia, sealing pressure at calibration T2 = 460°R, sealing temperature at well P2 = 14.7 psia, sealing pressure at well Tr = 660°R, calibration temperature AP = 660 [14.7/460 — 14.7/540] = 3.1 psi While this error is small even under these somewhat maximal conditions, it nevertheless represents a practical situation which did occur, and which as a matter of fact gave rise to this note. Where AP is positive, as above, the correction is added to the measured pressure; where negative, subtracted from the measured pressure. This correction should also be considered in successive calibration runs where the gauge, for example, may be warm from a previous calibration at an elevated temperature. ERROR NO. 2 Where a small quantity of moisture (liquid water) is sealed within the gauge at atmospheric conditions, the increased vapor pressure of the water at higher well or calibration temperatures will cause an increase in internal pressure. This moisture will come presumably from condensation within the gauge following temperature changes, from moisture on the operator's hands, and from atmospheric moisture (rain, mist, fog, etc.). Calculation shows that approximately 0.2 cc of water (three to four drops) is sufficient to saturate the air within an Amerada RPG-3 Gauge at 160°F, at which temperature the vapor pressure of water is about 5 psia. As the vaporization occurs in a sealed volume, the increase in internal pressure will be in excess of this 5 psi. At higher temperatures the pressures will be higher; however more water will be required to saturate the air within the gauge. Some experimental work was carried out with an Amerada RPG-3 Gauge at 200°F fitted with a 1,000 psi element, both with a dry recording chamber and with a small amount of water added. The results directly proved the existence of the error due to the presence of moisture, and, it is felt, indirectly, due to the differences in sealing temperatures and pressures, as both effects may be ascribed simply to an increase in the moles of gas within the recording chamber. SUMMARY In precision measurements the error introduced by sealing the gauge during a well test at a different temperature and pressure from that of calibration may be corrected for by using the equation presented, or it may be prevented by taking care always to seal the gauge at near calibration conditions. The error introduced by sealing moisture in the gauge may be prevented by taking care to keep moisture out of the gauge, or by removing the moisture by either warming or evacuating the gauge. Both of these errors are independent of the range of pressure measurement and the type of gauge, and are in addition to the usual temperature correction. ACKNOWLEDGMENT Appreciation is expressed to W. B. Kendall, Geophysical Research Corp., Tulsa, Okla., who pointed out the error from differences in sealing temperatures during some winter work in Canada. ***

Jan 1, 1956

By E. S. Mardock, Robert E. Bush

The object of this paper is to report recent developments in the quantitative interpretation of radioactivity logs. The use of reference lines is described in the application of the new zero radioactivity reference line for the determination of neutron derived porosities is discussed. Illustrated examples are shown of logs from the reef limestone of the North Snyder Field and from the Lansing-Kansas City limestone of central Kansas. A method of using an interrelation factor calculated from the neutron and gamma ray curves, called the neutron Productivity number, for the estimation of productivity from sandstone formations is discussed. When used in a relative manner the neutron productivity number has aided in Predicting whether a given zone will produce gas or liquid or whether it is too shaly to produce. Examples of logs from wells in the Freites District, Venezuela, and in East Texas are shown to illustrate the application of the neutron productivitv number. INTRODUCTION The petroleum industry was introduced to some of the preliminary results of investigations into the quantitative interpretation of radioactivity logs in October, 1949." It was stated at that time that the methods presented were entirely relative because they involved the use of reference points obtained from the radioactivity log, i.e., shale reference lines, dense zone reference lines, or a combination of both shale and dense zone reference lines. These relative methods offered many advantages to the industry in interpreting radioactivity logs in terms of porosity with particular application to limestone and dolomite reservoirs. However, these relative methods did not offer the wide range of applicability desired because the esta1)lishment of reliable reference points from shale in some areas were difficult. It was recognized that a more reliable mean; of establishing reference lines was vitally needed. Such a method is now available through the introduction of an instrumeutal zero device. It is the purpose of this paper to discuss the application of this new zero reference to the quantitative interpretation of radioactivity logs. Previously all applications of quantitative interpretations of radioactivity logs have been made in limestone reservoirs with little or no emphasis placed on sandstone reservoirs. A brief resumé of investigations into the quantitative interpretation of radioactivity logs in sandstone reservoirs is presented here. This discussion deals primarily with the interrelation of the gamma ray and neutron curves and the response of the latter to the density of the fluids filling the pore space in relatively homogeneous sandstones of uniform porosity. The authors believe that the methods presented herein are only applicable locally to specific fields and reservoirs, and that they probably do not offer a wide range of applicability. However, tile authors believe that the wider use of the new instrumental zero references in sand areas will reveal more information about the specific response of the gamma ray and neutron curves to changes in lithology and saturation. Two applications of quantitative interpretation using the new instrumental zero references are presented. Examples are given which show the comparison of logs and porosity in the limestones and dolomites of West Texas and Kansas. Logs of wells in 'Venezuela and East Texas are compared with the drill stem test data, production data, etc.. to illurtrate the interrelation of the gamma ray and neutron curve: and the rise of methods involving these interrelations to determine certain saturation variables. THE QUANTITATIVE APPLICATION OF RADIOACTIVITY LOGS TO LIMESTONE AND DOLOMITE RESERVOIRS Tile theoretical basis for the gamma ray and neutron curves has been discussed elsewhere.9 he method of recording the logs and apparatus involved has also been thoroughly covered and will not be discussed here.'."".'" It has been shown that the neutron curve responds exponentially to liquid filled porosity over the 1 1/2 to 35 per cent

Jan 1, 1951

By Robert E. Bush, E. S. Mardock

The object of this paper is to report recent developments in the quantitative interpretation of radioactivity logs. The use of reference lines is described in the application of the new zero radioactivity reference line for the determination of neutron derived porosities is discussed. Illustrated examples are shown of logs from the reef limestone of the North Snyder Field and from the Lansing-Kansas City limestone of central Kansas. A method of using an interrelation factor calculated from the neutron and gamma ray curves, called the neutron Productivity number, for the estimation of productivity from sandstone formations is discussed. When used in a relative manner the neutron productivity number has aided in Predicting whether a given zone will produce gas or liquid or whether it is too shaly to produce. Examples of logs from wells in the Freites District, Venezuela, and in East Texas are shown to illustrate the application of the neutron productivitv number. INTRODUCTION The petroleum industry was introduced to some of the preliminary results of investigations into the quantitative interpretation of radioactivity logs in October, 1949." It was stated at that time that the methods presented were entirely relative because they involved the use of reference points obtained from the radioactivity log, i.e., shale reference lines, dense zone reference lines, or a combination of both shale and dense zone reference lines. These relative methods offered many advantages to the industry in interpreting radioactivity logs in terms of porosity with particular application to limestone and dolomite reservoirs. However, these relative methods did not offer the wide range of applicability desired because the esta1)lishment of reliable reference points from shale in some areas were difficult. It was recognized that a more reliable mean; of establishing reference lines was vitally needed. Such a method is now available through the introduction of an instrumeutal zero device. It is the purpose of this paper to discuss the application of this new zero reference to the quantitative interpretation of radioactivity logs. Previously all applications of quantitative interpretations of radioactivity logs have been made in limestone reservoirs with little or no emphasis placed on sandstone reservoirs. A brief resumé of investigations into the quantitative interpretation of radioactivity logs in sandstone reservoirs is presented here. This discussion deals primarily with the interrelation of the gamma ray and neutron curves and the response of the latter to the density of the fluids filling the pore space in relatively homogeneous sandstones of uniform porosity. The authors believe that the methods presented herein are only applicable locally to specific fields and reservoirs, and that they probably do not offer a wide range of applicability. However, tile authors believe that the wider use of the new instrumental zero references in sand areas will reveal more information about the specific response of the gamma ray and neutron curves to changes in lithology and saturation. Two applications of quantitative interpretation using the new instrumental zero references are presented. Examples are given which show the comparison of logs and porosity in the limestones and dolomites of West Texas and Kansas. Logs of wells in 'Venezuela and East Texas are compared with the drill stem test data, production data, etc.. to illurtrate the interrelation of the gamma ray and neutron curve: and the rise of methods involving these interrelations to determine certain saturation variables. THE QUANTITATIVE APPLICATION OF RADIOACTIVITY LOGS TO LIMESTONE AND DOLOMITE RESERVOIRS Tile theoretical basis for the gamma ray and neutron curves has been discussed elsewhere.9 he method of recording the logs and apparatus involved has also been thoroughly covered and will not be discussed here.'."".'" It has been shown that the neutron curve responds exponentially to liquid filled porosity over the 1 1/2 to 35 per cent

Jan 1, 1951

By R. W. Ph. D. Raymond

PROFESSOR W. P. BLAKE, in a note to his Catalogue of California Minerals, pointed out that the mining districts of the Pacific slope are arranged in parallel zones, following the prevailing direction of the mountain ranges. This interesting generalization has been more fully illustrated and connected with the geological history of the country by Mr. Clarence King, who sums tip the observed phenomena as follows: "The Pacific coast ranges upon the west carry quicksilver, tin, and chromic iron. The next belt is that of the Sierra Nevada and Oregon Cascades, which, upon their west slope, bear two zones, a foot-hill chain of copper mines, and a middle line of gold deposits. These gold veins and the resultant placer mines extend far into Alaska, characterized by the occurrence of gold in quartz, by a small amount of that metal which is entangled in iron sulphurets, and by occupying splits in the upturned metamorphic strata of the Jurassic age. Lying to the east of this zone, along the east base of the Sierras, and stretching southward into Mexico, is a chain of silver mines, containing comparatively little base metal, and frequently included in volcanic rocks. Through Middle Mexico, Arizona, Middle Nevada, and Central Idaho is another line of silver mines, mineralized with complicated association of the base metals, and more often occurring in older rocks. Through New Mexico, Utah, and Western Montana lies another zone of argentiferous galena lodes. To the east, again, the New Mexico, Colorado, Wyoming, and Montana gold belt is an extremely well-defined and continuous chain of deposits." These seven longitudinal zones or chains of mineral deposits must

Jan 1, 1873

By CARL B. SNYDER

PERHAPS the most extraordinary thing about business, the trade and production of the country as a whole, is its amazing continuity and growth, its momentum and energy. It goes on year after year, growing steadily, almost without breaks, in spite of every kind of disturbance. We have been grossly deceived into the idea that business is highly variable. We have taken a few things like pig iron, and the like, constructional activity broadly, and imagined that these are a trustworthy measure of trade. Actually they are the worst that we could find. They do not apply to more than 10 per cent or, at the most, possibly 15 per cent of the total of the country's industrial activity. The other 85 or 90 per cent, or even more, goes on growing surely and steadily just like the growth of population and the steady advance in technique, invention, discovery, and improved methods of production Let me give you what seems to me one of the most remarkable examples of this amazing momentum and regularity. You know that 90 per cent or more of the business of the country is done 'by means of checks. About seven-eighths of the total of all checks drawn are reported regularly every week in the newspapers. Let us follow these reports from week to week, just as they come, and plot them up against the correspond- ing weeks of last year, and the year before, and the gear before that, as far back as you would like to go. Take especially the figures for 140 selected cities out- side of New York.

Jan 1, 1929