Search Documents

By K. R. Janowski, A. B. Chase, E. J. Stofel

Ruby crystals of exceptional optical quality have been grown from fluxes composed of Bi2O3 + PbF2 or Bi2O3 + BiF3. Careful control of growth conditions was required to minimize the number of growth defects consisting primarily of dislocations, occluded flux, and growth twins. Slow growth rates coupled with the addition of small amounts of La2O3 as a flux dopant were helpful in producing nearly perfect crystals. Chromium concentrations up to 1 pet were incorporated into these crystals without adversely affecting their perfection. Crystals up to 10 mm in diameter having as few as one to ten dislocations per crystal were typical of those produced under optimum growth conditions. Under these same conditions the occlusions were eliminated, and growth twins were either eliminated or reduced to one to three twin boundaries per crystal. INTEREST in the nature of lattice imperfections produced during the growth of ruby crystals (Al2O3-corundum structure) has been stimulated recently by the need for ruby lasers of good optical uniformity. As a result, ruby crystals grown by the flame-fusion (Verneuil) process have been studied in detail and have been found to contain high densities of dislocations (106 to 107 dislocations per sq cm) and mosaic structures that impair their optical quality.'-3 Attempts to improve the quality of Verneuil-grown crystals by controlling the growth variables have not been entirely successful. On the other hand, rubies grown by the flux process have received little attention even though their more nearly equilibrium growth conditions suggest that they would have fewer growth defects. Nelson and Remeika have shown recently that small flux-grown rubies can indeed be made into very low-loss lasers. However, they did not report information on crystalline imperfections in these crystals.4 Stephens and Alford have reported briefly on defects found in a flux-grown corundum crystal but they neither described these defects in detail nor related them to the method of growth.5 The present investigation was undertaken to establish the relationship between growth conditions and crystalline perfection of flux-grown rubies, sapphires, and other crystals of the corundum family. EXPERIMENTAL PROCEDURE The corundum crystals used in this study were grown by slowly cooling solutions of A12O3 in molten-salt solvents of PbO + PbF2, Bi2O3 + PbF2 or Bi2O3 + BiF3. The materials employed were Linde A (a Al2O3 powder) with reagent-grade chemicals as solvents. Some of the solutions also contained small additions (1 pet or less) of one or more of the transition metal elements chromium, manganese, iron, and titanium as crystal dopants. La2O3 was added to some of the solutions to alter the growth habit of the crystals. The La2O3 promoted the occurrence of growth facets parallel to (0112) and {1011} planes, where the indexing system is the morphological system described in detail by Kron-berg6 and used throughout this paper. The melts from which the crystals were grown were prepared by mechanically mixing the various constituents and placing them in platinum crucibles. The covered 50- and 100-ml platinum crucibles were heated in muffle furnaces at 1250°C for short periods of time (1 to 4 hr) and then program-cooled at either 2° or 4°C per hr to 1000°C. At this lower

Jan 1, 1965

By M. A. Torcaso, P. Raimondi

To study mass transport in systems simulating oil recovery processes, different porous media were saturated with a mobile (carrier phase) and a stationary phase. Slugs of carrier phase containing a small amount of solute were displaced with pure carrier phase. By analogy to the chromato-graphic processes, the velocity of the solute can be predicted from a knowledge of the partition coefficient and the saturation provided that equilibrium between the two phases exists. Equilibrium was found to exist for different porous media, solutes and rates. The conditions were varied over the range normally encountered in the laboratory and in the field. The longitudinal dispersion of a solute undergoing interphase mass transfer was also investigated. INTRODUCTION The production of hydrocarbons by gas cycling, enriched gas drive and C02 or alcohol displacement involves, among other factors, relative motion between two phases and compounds, hereafter called solute, which are soluble in both phases. The solute is carried forward by the faster flowing phase at a lower velocity than the average velocity of that phase. Retardation of the solute is caused by chromatographic absorption and desorption in the slower flowing phase and by the degree of departure from equilibrium. At equilibrium the concentration of solute in the two phases can be related by the equation* CSw = K Cso ,............(1) where C, and C are the concentration of solute in the aqueous and oleic phases respectively and K is the equilibrium ratio, or partition coefficient. Displacement theories must contain an explicit assumption with regard to equilibrium, i.e., whether the compositions can be related by Eq. 1. The existance of equilibrium depends, in general, on the relative velocity between the phases. Unfortunately, other factors such as gravity segregation and viscous fingering, also depend on velocity. For this reason, whenever effects of rate on displacement were observed,2-4 it was practically impossible to discern what caused them — lack of equilibrium or the factors mentioned above. Equilibrium between phases has been the subject of extensive studies in fields such as extraction or chroma to graphy. It has received only small attention in flow through the type of porous media encountered in oil production.5 For this reason a method was developed which makes it possible to study the movement of a solute as it is affected by rate, type of porous media, partition coefficient and carrier phase, but in the absence of segregation or fingering. The information obtained enables one to determine when the assumption of equilibrium can be made. Briefly, the method consists of (1) saturating the core with a mobile and an immobile phase, (2) injecting a slug made up of the same fluid as the mobile phase and a small concentration of mutually soluble solute, (3) measuring the lag and the peak height of the slug at arrival and (4) correlating these variables with fluid properties such as partition coefficient and mixing constants of the medium. PROPOSED MECHANISM The principles of chromatography are combined with the equation of longitudinal mixing to predict the velocity of a solute slug compared to the bulk velocity and the peak height of a slug.6-9 The equation so obtained is valid under equilibrium conditions only. Therefore, a comparison between experimental and predicted results will give a measure of departure from equilibrium. This work was done with either the oleic or the aqueous phase being immobile. For simplicity, the following development is based on the case where the oleic phase is immobile. However, the treatment is the same in either case.

Jan 1, 1966

By Willard P. Ward

Having been engaged during the past year in the manufacture of ferro-manganese in a blast furnace, I have imagined that some further information on this subject might be of interest to that large number of members of the Institute who are engaged in the iron and steel industries. The great question of the economical production of good steel, ingot metal, or homogeneous iron (we scarcely know now what to call it) from good materials, and at reasonable prices, has, thanks to the intelligence and energy of a few American engineers, been successfully solved in this country. Nearly all first-class railroads, and many that would not rank so high, have adopted the Bessemer rail. Martin boiler-plates are rapidly gaining ground, in competition with

By William F. Boericke

THERE was a time when the selection of fire brick was .left to the judgment of the head bricklayer of the plant, whose choice was not unaffected by a box of Christmas cigars from a friendly salesman. But the days are past when it was generally believed, with complacent philosophy, that bricks were bricks without much distinction, and should be bought on a price basis alone. Gone, too, is the belief that in certain types of industrial work the eventual failure of refractories was assured. Modern metallurgical practice, with its trend toward handling larger tonnages at higher temperatures, demands the use of refractories that cannot be supplied by random guess. The logical development is to inquire into the properties of the brick to be purchased, and this resolves itself into the use of specifications. In 1925, the General Refractories Co., with the active support and hearty cooperation of some of its larger customers, established a laboratory, at its Baltimore plant, for testing and research in refractories. This was the outgrowth of a growing appreciation of the value of research in the refractory field. Since then the work has become more involved' and the aims more ambitious, so that the present laboratory now employs a staff of 11 men working, under the direction of trained refractory technologists, on problems of research as well as the routine control of manufacture. It is believed s that `this type of laboratory is a comparative novelty among refractory manufacturing plants. It handles the testing and research work for all the 15 plants of the organization. Being at one of the works has the advantage of making it possible to carry on large scale plant tests on new products after the preliminary laboratory tests have been successfully completed.

Jan 1, 1929

By C. M. Fellman

AVAILABLE data for the first nine months of the Year indicate that accident occurrence in metal mining was well on its way to an all-time low for 1939. However, the relatively rapid pickup in mining production in the fall will be likely to boost both accident occurrence and also accident rates. Results of the National Safety Competition for 1938, the fourteenth of its kind conducted by the U. S. Bureau of Mines, were published in August, 1939. W. W. Adams, statistician of the bureau, states that "with 345 mines and quarries competing, more than in any previous year except 1931, the contest revealed low accident rates at many of the enrolled plants and, which is even more remarkable, it revealed 113 mines and quarries at which no lost- time accidents occurred during the con- test year." The National Safety Competition provides a means whereby mines and quarries may engage in active competition to stimulate their safety programs. Companies in the contest can compare their records with those of similar plants operating elsewhere and thereby determine to what extent their safety programs are successful. The Joseph A. Holmes Safety Association gave over 150 awards for safety performance in the mineral industries in 1939 and a remarkable phase of these awards was the considerable number given to individual miners who had worked fifty or more years without sustaining a lost-time accident.

Jan 1, 1940

By C. W. Dunham

FROM the primary gyratory crushing plant, described in MacLeod's article, ore is delivered to a large storage or surge bin from which it is carried by two transverse conveyors to the secondary crushing plant. The bin has a useful drawoff of about 13,000 tons, this being slightly over one half of the initial daily capacity of the Morenci Reduction Works. This arrangement provides sufficient storage to permit intermittent operation of the primary and secondary crushing plants without too close a coordination between the two.

Jan 1, 1942

By A. S. Appleton

The diffusion of carbon in Fe-Co-C austenites was studied as a function of cobalt concentration up to 12 at. pet, using an autoradiographic technique. The diffusion coefficient was found to initially decrease and then increase with increasing cobalt concentration, the trends being more marked the higher the temperature of diffusion. These effects were paralleled by variations in the activation energy and the constant for diffusion which, however, were found to be dependent also on the carbon content. The results are compared with the previously available data and their significance is discussed in terms of the kinetics of solid-state reactions in this systern. THE influence of cobalt on the diffusivity of carbon in austenite was first studied by Smoluchowski,' his data being that most commonly cited in works

Jan 1, 1964

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary, 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. BENJAMIN B. LAWRENCE. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. HENRY A. WENT WORTH,. Secretary-Treasurer, 60 India St., Boston, Mass. A. H. EUSTIS. F. G. STANTIAL. Columbia Holds four sessions during year. Annual meeting in September or October. FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER. - FRANCIS A. THOMSON.

Jan 12, 1915

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman, JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary, 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia Holds four sessions during year. Annual meeting in September or October. FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 9, 1915

By J. C. Savins, G. C. Wallick, W. R. Foster

The dual differentiation-integration method of rbeological analysis is applied to Couette flow. Using machine processing techniques, a spectrum of characteristic derivative functions for a variety of ideal Generalized Newtonian and viscoplastic models has been developed; As for the case of Poiseuille flow the functions for Generalized Newtonian models as a class are strikingly different from the corresponding functions for the class of viscoplastic models. It is shown that this dual scheme of analysis is a highly sensitive analytic method for dotermining the applicable range if a rbeoloaical model. The unique characteristics of this function in the case of viscoplastics may lead to a more precise detection and evaluation of the yield point or yield stress in these materials. INTRODUCTION It has been shown 1,2 that the dual differentiation-integration method of analysis is a discriminating and flexible method for interpreting flow behavior and determining the applicable range of a particular model from Poiseuille flow experiments. In the preceding paper3 the basic equations governing the Couette flow experiment were reviewed and the significance of changes in boundary conditions on data analysis in the case of the viscoplaaic discussed. In this paper the dual method of analysis is applied to Couette flow using the suites of rheological models considered previously.

By Magnus Troilius

The heat-calculations of gas-analyses involve cumbrous multiplications, which are apt to lead into errors. The foliowing tables and formulae have been found useful as facilitating such calculations, and therefore I hope that they will be of interest to some of the members. By "heat-unit" will, in the following, be understood the amount of heat required to raise the temperature of 1 kilogram of water l° Cent. All the tables refer to cubic meters at O0 and 760 mm. pressure. The following gas is chosen as an example: C02, - 4.0 vol. per cent. co, = 20.0 " CHI, - 3.5 " H, - 7.0 " N, - 65.5 " " 100.0

Jan 1, 1884

The sum of $250 was appropriated to the Chicago Section. The President was authorized to appoint five members of the Board of Directors, including himself as Chairman, to discuss with other technical societies the proper organization for handling all matters of joint interest to the profession of engineering as distinct from purely technical activities, and to submit its findings in the form of recommendations to the Board of-Directors. Charles F. Rand was appointed a Trustee of the United Engineering Society to succeed himself. John H. Janeway was elected a member of the Library Board, vice Karl Eilers, resigned. Alexander C. Humphreys was elected a member of the Library Board to succeed himself.

Jan 1, 1917

By W. L. Freyberger

In a study of the kinetics of flotation of coal, employing a single-cell continuous flotation system, Jowett and Safvi1 pointed out that it was experimentally impossible to float all of the coal which could be floated in a batch tests. On the other hand, deBruyn and Modi, in a discussion of their paper, suggested that under certain conditions the recovery of floatable material from a similar one-cell continuous system would have been 100%.2 Both of these pairs of authors make the assumption that a state of perfect mixing exist in the flotation cell. This assumption, usually made by investigators studying flotation kinetics in a continuous system, has been confirmed experimentally on several occasions. The work is summarized by Arbiter and Harris.3 It is the purpose of this note to demonstrate that, for conditions of perfect mixing, one of two conditions exist: 1) the recovery of floatable material is 100%, and the flotation is infinitely fast, or 2) the recovery of floatable material must be less than 100%. This theorem can be proved simply in the following manner: 1) If recovery, R, of the floatable material is 100%, the concentration in the tailing must be zero. This follows from the definition of recovery as

Jan 1, 1964

By H. C. Ray

ABOUT the beginning of 1930, coal preparation had reached the stage where the cleaning of coal by liquid or air had become the order of the day. Since that time many new preparation plants have been installed in spite of the years of depression in the coal industry, and this is indicative of a trend wherein the coal producer found it expedient to manufacture a cleaner product in order to compete with other fuels. It was also about 1930 that, because of the difficulties encountered with fine coal in cleaning plants, dust collectors came into use. Both cleaning plants and dust collectors, therefore, were much discussed at the engineering meetings of the early 1930's. During these meetings the many advantages to be gained through the use of dust-collecting systems were pointed out by Hebley,1 Appleyard2 and others. The great possibilities of new markets for this product were emphasized and discussed at the same time; however, the disposal of the collected dust remained a problem. Since the purpose of dust collecting is to improve the preparation and, consequently, the salability of the coal, it seems illogical to return the collected dust to any of the coal being prepared for market use, as is done in preparation plants that include dust-collecting systems. The logical thing is to dispose of the dust in some useful and practical manner outside of the tipple. As a practical matter, this can be done in one or both of two ways; either by consuming the dust at the mine's own power plant or by marketing the dust direct to the consumer. The latter method not only offers the greatest opportunities, but is the most important, because of inequalities that may exist between the quantity of dust collected and the consuming capacity of the mine's power plant. In considering the more important marketing possibilities, we are confronted immediately with the problems connected with the handling and transportation of so fine a material. It is this problem, rather than the problem of finding new markets, that has been responsible for the lack of progress in the matter of dust disposal. It is the purpose of this paper to point out again some of the potential market outlets, and also to describe an existing system of handling and transporting coal dust. To the best of the writer's knowledge, this is the first and only operation in this country that has handled fine-mesh coal in bulk 50-ton lots direct to the consumer. POtential Markets for Fine-mesh Coal Dust In general, the potential market outlets would include any operation of which the pulverization of coal is a necessary part. To be more specific, a few of the better known operations of this type must include: colloidal-fuel plants, briquetting plants, "sea coal" distributing plants, water-purification plants and, obviously, pow-

Jan 1, 1944

By H. C. Ray

ABOUT the beginning of 1930, coal preparation had reached the stage where the cleaning of coal by liquid or air had become the order of the day. Since that time many new preparation plants have been installed in spite of the years of depression in the coal industry, and this is indicative of a trend wherein the coal producer found it expedient to manufacture a cleaner product in order to compete with other fuels. It was also about 1930 that, because of the difficulties encountered with fine coal in cleaning plants, dust collectors came into use. Both cleaning plants and dust collectors, therefore, were much discussed at the engineering meetings of the early 1930's. During these meetings the many advantages to be gained through the use of dust-collecting systems were pointed out by Hebley,1 Appleyard2 and others. The great possibilities of new markets for this product were emphasized and discussed at the same time; however, the disposal of the collected dust remained a problem. Since the purpose of dust collecting is to improve the preparation and, consequently, the salability of the coal, it seems illogical to return the collected dust to any of the coal being prepared for market use, as is done in preparation plants that include dust-collecting systems. The logical thing is to dispose of the dust in some useful and practical manner outside of the tipple. As a practical matter, this can be done in one or both of two ways; either by consuming the dust at the mine's own power plant or by marketing the dust direct to the consumer. The latter method not only offers the greatest opportunities, but is the most important, because of inequalities that may exist between the quantity of dust collected and the consuming capacity of the mine's power plant. In considering the more important marketing possibilities, we are confronted immediately with the problems connected with the handling and transportation of so fine a material. It is this problem, rather than the problem of finding new markets, that has been responsible for the lack of progress in the matter of dust disposal. It is the purpose of this paper to point out again some of the potential market outlets, and also to describe an existing system of handling and transporting coal dust. To the best of the writer's knowledge, this is the first and only operation in this country that has handled fine-mesh coal in bulk 50-ton lots direct to the consumer. POtential Markets for Fine-mesh Coal Dust In general, the potential market outlets would include any operation of which the pulverization of coal is a necessary part. To be more specific, a few of the better known operations of this type must include: colloidal-fuel plants, briquetting plants, "sea coal" distributing plants, water-purification plants and, obviously, pow-

Jan 1, 1944

By T. D. Yensen, R. K. McGeary

While we have not been primarily interested in the determination of hydrogen in the alloys that we have been dealing with, we arc very glad to cooperate in this symposium on sampling and analysis for hydrogen, as we can never tell when we may find it desirable to perform such analyses. Vacuum-fusion Method Our primary interest has been oxygen and carbon, in the analysis of which we think we have become very proficient. Our oxygen-analyzing apparatus is of the vacuum-fusion type (Fig. I). This employs Dr. Derge's type of graphite cruciblc and slit sleeve, with graphite powder between, for heat insulation (Fig. 2) supported in a clear quartz bulb connected to the Pyrex glass system by means of a carefully made ground joint. The latter is kept cool by means of an air blast from a circular copper tube surrounding the joint. The crucible is heated by high-frequency induction and the 24 one-gram samples successively dropped in from the horizontal tube at the top by means of a magnet. The gases (H², CO, N2) are passed through the CuO catalyst held at 300°C. (converting CO to CO²I, H² to H²O) and the CO² and H2O frozen out in the main liquid air trap, while N2 is evacuated. At the end of the operation, shown by the termocouple vacuum gauge indicating a pressure of 10-4 mm. Hg, the analyzing system is isolated by means of the mercury cutoffs, and the CO² and H2oare determined by transferring first the CO2 and then the HzO to the small trap at the right. This is done by placing liquid air on the small trap, then removing the liquid air from the large trap for one minute, which is sufficient to evaporate the Co2 and transfer it to the small trap. The CO2 is then measured by closing the mercury cutoff at the extreme right, removing the liquid air from the small trap, warming it up to room temperature, adjusting the mercury level to one of the three marks on the glass tube (corresponding to three volumes calibrated so that I mm. Hg of CO² corresponds to 0.001, 0.002 and 0.010 mg., respectively, of oxygen) and finally reading the pressure. Liquid air is now replaced on the large trap, the mercury cutoff at the right opened, transferring the COz back to the large trap. The cutoff to the pumps is then opened, the liquid air removed for one minute, thus evacuating the CO², the pumps again cut off and the H2 O transferred to the small trap as before, except that it is now necessary to warm the large trap with a Bunsen burner in order to evaporate all the H2O. This requires about three minutes, as the inner tube must be heated to at least 100°C. In order to prevent H²O from being adsorbed on the glass walls, the glass tubing beyond the catalyst (i.e., to the right in Figs. I and 3) is kept heated to about 150°C. by means of Nichrome ribbon as shown in Fig. 3. For a I-gram sample the above amounts of oxygen (0.001, 0.002 and 0.010 mg.) 35

Jan 1, 1945

By Albert S. Trube

The purpose of this paper is to clarify the definition of compressibility and to present a uniform basis upon which instantaneous compressibilities of liquids and gases can be compared. The equations gaverning the instantaneous compressibilities of imperfect gases are derived and the concept of pseudo-reduced compressibility is introduced. Part of the data presented by Brown, Katz et a1 on compressibility factors for natural gases has been rearranged. A graph of pseudo-reduced compressibility vs pseudo-reduced pressure for various pseudo-reduced temperatures is presented. The need for additional work in relating the compressibilities of liquids and gases is discussed. This information should be of value to reservoir engineers in making non-steady state performance calculations in gas reservoirs. It should be of further use irz pointing the direction for additional research in the nature of liquid and gas compressibilities. INTRODUCTION With the increasing use of steady and non-steady state well and reservoir data, there is a corresponding increase in the importance of the various factors entering into such calculations. Increasing emphasis is being placed on the necessity for obtaining reasonably accurate estimates of the physical properties of the reservoir fluids well in advance of the more accurate laboratory data. One such factor is the isothermal coefficient of expansion of the media which are transmitting and attenuating the non-steady state pressure waves. The average isothermal coefficient of expansion, or "compressibility" is a complex function controlled by the physical properties of the formation and the fluids contained therein. The isothermal expansion coefficients for reservoir gases are usually quite variable, in many cases being highly-pressure sensitive. The coefficients for reservoir liquids tend to be pressure sensitive, but not nearly so much as reservoir gases. The coefficients for solids, usually expressed in terms of a "modulus of elasticity" are relatively insensitive to pressure variations within their elastic limits. For this reason, and also because many previous applications have been limited to rel- atively small pressure ranges, there has been a tendency to ignore the variable nature of isothermal expansion coefficients and treat them as constants. Also, the term "compressibility" by which these coefficients are generally designated is commonly confused with a similar term, z, used to define the deviation of an imperfect natural gas from the perfect gas laws. A clear distinction should be made at the outset between the term "compressibility", which is an isothermal coefficient of expansion of a substance, and the term "compressibility factor", z, which refers to the deviation of a gas from the perfect gas laws. Although the scope of this paper is limited to the compressibility of single phase natural gases, it is definitely related to the problem of accurately estimating the compressibilities of single phase hydrocarbon reservoir liquids, which will form the basis of a future presentation. BASIC PRINCIPLES The coefficient of isothermal compressibility of a substance, c, is usually determined from pressure-volume or pressure-length -measurements depending upon whether the substance is single phase gas, liquid, or solid. A convenient method for making such estimates for a finite change in pressure and volume at constant temperature is to use the well known equation V1-V2/V1 (p2 - p1) .....(1) Eq. 1 is negative because the volume of a confined substance decreases as the pressure is increased. In this case V1 > V2 and p2 > p1. This equation is useful in approximating the compressibilities of single phase gases and liquids undergoing small pressure changes. It is evident, however, that this equation is almost identical with the determination of Young's modulus of elasticity for solids. If the assumption is made that change in length is directly proportional to change in volume, as would very nearly be the case for a steel rod in tension within its elastic limit, then E5=-L1 (p2 - p1)/L1 - L2 .......(2) in which E. is the isothermal expansion coefficient, or Young's modulus of elasticity, for a solid. And further, for this special case L1 (p2 - p1)/L1 - L2 .......(3)

Jan 1, 1958

By R. K. Matheson

THE Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 19o tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65° From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. CHOICE OF RAISE A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. TIME SCHEDULE As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1942

By R.K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By R. K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943