Search Documents

By W. Spencer Reid

ALTHOUGH there have been some developments during the last five years which have had far- reaching and important bearing on lead smelting, it cannot be said that any basic principles of pyrometal-lurgy have been discovered. Eighteen or twenty years ago the Dwight & Lloyd sintering machine was intro-duced and literally turned the roasting end of lead smelting upside down. There has been nothing com-parable to the advent of the sintering machine during recent years. Actual blast-furnace practice today is slightly, if any, better than it was five years ago ; although immeas-urably better than it was twenty to thirty years ago. Some tell us that as far as cleanness of slags is con-cerned, it is no better today than in the days of the old Romans. The metallurgist of a generation ago did very good work, considering the equipment he had available. It is true he was working with the cream of the ores, the clean oxides and carbonates and the low-zinc sul-fides. He was troubled very little with high zinc and selected his type of slag according to preference of -some authority such as Eilers, Iles, Raht, Hahn, etc. As these free-smelting ores were depleted the complex ores were encountered, and the metallurgist gradually discovered that he had to forget the old type slags and run a slag according to the percentage of zinc on the charge. I believe it is now universally agreed that SiO2 and CaO must be lowered and FeO raised in a slag as the ZnO increases. The ratio of these variations is practically uniform and can be relied upon over wide fluctuations of the determining element, zinc. These "bastard" slags, as they are sometimes inappropriately designated, are actually in daily use, and the metallurgist of today has been forced to adopt certain standards, as a guide to successful operation. These slags practically refute the old Eilers' theory that all good slags are chemical combinations of SiO2 with FeO and MnO, and CaO and MgO. Eilers' and the other type-slag theories were based upon the assumption that a good slag must con-form to a definite formula, such as 3 (FeO)2 SiO2 + 2 (CaO)2 SiO2 or 2 (FeO)2 SiO2 + 2 (CaO)2 SiO2 which respectively figure 31.3 and 36 per cent SiO2. The SiO2 was supposed to remain constant even with the entrance of impurities such as Zn and A1,0? into the slag. The increasing amount of impurities, espe-cially Zn, soon discredited the theory, for in actual practice the slag failed to run freely.

Jan 1, 1927

By B. H. Kear

Clustering of slip bands in different systems has been observed in both ordered and disordered Cu3Au crystals compressed in the <110> orientation. Certain features of the slip band patterns are explained in terms of reactions between dislocations with Burgers vectors at 120 deg; in a few rare cases, the slip band evidence suggests that the Products of such reactions form diffuse tilt boundaries between the differently slipped regions of the crystal, similar to the known behavior of ionic crystals, but not nearly so well defined. WHEN crystals with orientations favorable for multiple slip undergo plastic deformation, slip may occur in different systems in localized regions, so that clusters of slip bands are developed. This phenomenon has been observed in fee1-4 metals and also in ionic crystals having the sodium chloride structure.5-8 In the ionic crystals, the boundaries formed between the differently slipped regions of the crystal assume characteristic orientations and are associated with macroscopic tilts that are plainly visible on the sides of the crystal. Recently, this interesting feature was explained in terms of the formation of diffuse low-angle boundaries as a result of interactions between families of glide dislocations in the different systems meeting in the boundaries.9 This paper describes an attempt to obtain similar evidence for boundary formation in an fee crystal. The alloy Cu3Au was chosen for the present study simply because this material is currently being used in a general study of differences in deformation behavior of the ordered and disordered phases of this alloy, which will be described elsewhere. EXPERIMENTAL PROCEDURE The two specially oriented compression specimens used in the present study were prepared from a melt-grown single crystal by careful cutting, grinding and polishing. The finished specimens were about 6 mm by 2 mm in cross section by 6 mm tall, with their ends parallel to (101) and sides parallel to (111) and (121); the broad faces of the specimens were made parallel to (711). Both specimens were annealed in an evacuated quartz tube at 850oC for several hours, slowly cooled to 500°c, and then quenched into water in order to obtain the disordered state for the alloy. One of the specimens was partially ordered (with S- 0.8) by reannealing at 350oC for 100 hr. After these annealing treatments, both of the specimens were electropolished. 10 Finally, the specimens were compressed in the [loll orientation and their stress-strain curves were recorded. The deformation was carried out in increments of a few percent strain. At each stage in the deformation the specimens were unloaded, removed from the compression jig, and examined optically for slip bands. Before reloading, the specimens were repolished, so that the observed slip band patterns were characteristic of a particular stage in the deformation. EXPERIMENTAL RESULTS Fig. 1 show!; the stress-strain curves for the ordered and disordered specimens and also indicates the stages 1, 2, and 3 where the deformation was interrupted for examination of slip bands. The curves show marked differences in flow stress and in work hardening rate in the two specimens, as observed by previous workers.11,12 Also, it was found, in agreemement with the observations of Taoka and Sakata,&apos;3 that the plastically deformed disordered alloy showed the characteristic coarse slip bands of alloys, whereas the ordered alloy exhibited a fine slip band structure similar to that of pure metals. Slip Band Observations. In what follows, the description of the slip band patterns, with accom-

Jan 1, 1962

By John A. THOMPSON, Pazcl D. Torrey, Frank Breayster

DISCOVERY of natural gas in the Dundee field of New York in February, 1930, and the subsequent discovery in Tioga in September of that year, focused the attention of the natural-gas industry on the enormous possibilities of production and distribution in - the most populous area of the United States-New York and New England. Prior to 1926 the natural-gas industry in New York State had settled into a definite and limited policy, with the distributing companies controlling the output from its discovery to the ultimate consumer. Production amounted to between G and 7 thousand mil- lion cubic feet a year, with another 10,000 million feet imported from Pennsylvania for distribution in New York State. This gas was primarily from the Medina sand stone in. the western part of the state.

Jan 1, 1932

By Glenn A. Keep

THIS paper is not an announcement of the successful conclusion of the Cerro de Pasco Copper Corporation&apos;s pacos-pyrite problems, but merely a description of the commercial-scale, intermittent-roasting operations conducted by the writer, J. H. Lucas and others of the staff. It was prepared by request, for presentation at the February meeting of the Institute. The results obtained in Peru confirm the 1-ton-a-day experiments completed about three years ago at Kearny, N. J. by C. C. Gordon and Mr. Lucas, where it was first demonstrated that a mixture of about 80 per cent. pacos ore with 10 per cent. pyrite ore and 10 per cent. salt could be roasted intermittently in a small 1-ton-a-day Holt-Dern furnace without extraneous fuel, producing porous calcine that could be leached rapidly. Mr. Keep and his staff, by successfully introducing improvements in the construction of the commercial furnace and in their handling of material, have established beyond doubt a low cost for roasting. The other steps in the process of treating pacos and pyrite ores have not as yet been demonstrated as sufficiently conclusive to warrant their acceptance for a permanent plant. Cerro de Pasco Ores The ores of the Cerro de Pasco Copper Corpn. at Cerro de Pasco, Peru, are situated at an altitude of 14,000 ft. The town and mines are served by the Cerro de Pasco Railroad, which operates between Cerro de Pasco and Oroya, the site of the company&apos;s copper and lead smelters. Table 1.—Average Analysis of Cerro de Pasco Ores Pacos Ore Pykite Ore Silver, oz............................................... 10.3 12.0 Gold, oz................................................ 0.007 0.01 Lead, per cent........................................... 1.7 1.8 Copper, per cent......................................... 0.19 0.27 Zinc, per. cent........................................... 1.4 1.02 Iron, per cent........................................... 13.4 34.45 Silica, percent.......................................... 61.8 24.5 Alumina, per cent....................................... 2.5 0.62 Lime, per cent........................................... 1.5 0.20 Manganese, per cent..................................... 0.42 0.09 Sulfur, per cent,.......................................... 1.1 34.2

Jan 1, 1929

Commonwealth of Pennsylvania, Department of Internal Affairs, Topographic and Geologic Survey, Harrisburg, Pa George H. Ashley, State Geologist All available printed Bulletins may be obtained through the Commonwealth of Pennsylvania, Division of Documents. Where a price has been set on the publication, checks should be made out to the Commonwealth of Pennsylvania. A Syllabus of Pennsylvania Geology and Mineral Resources has recently been published by the Survey as Bulletin G1, and consists of a general survey of the state An appendix of this bulletin also gives a complete bibliography of Survey publications It will be sent upon request. The State Geological Survey has gone through several phases and reorganizations, publications of three of them being numerous and important A fire, in 1927, destroyed supplies of many of the papers of the present Survey. Available bulletins of the present Survey are: Bulletin M6: Bituminous coal fields of Pennsylvania, in 4 parts available as follows: pt 1, General description of coal, 50 cents; 3, Bituminous coal resources, 25 cents, 4, Analyses of bituminous coals, 25 cents Bulletin M10, Fire clays of Pennsylvania; Mll, Molding sands of Pennsylvania; M12, Anthracite culm and silt (1928); M13, Feldspar in Pennsylvania; M14, Magnetite deposits of French Creek (1931); County Report C1, Adams County, pt 1, Geology and geography (in press), County Report C2, Geology and mineral resources of Greene County (in press); Topographic and Geologic Atlas A5, New Castle Quadrangle (1929), $1; Topographic and Geologic Atlas A27, Pittsburgh Quadrangle (1929), $1; Topographic and Geologic Atlas A168, Lancaster Quadrangle (1930), $1. The present Survey has also issued a number of short mimeo¬graphed bulletins any of which will be sent upon request Briefly they are: No. 15, Mineral resources of Pennsylvania; 20, Iron ores; 28, Magnesite; 40, White clay deposits, Monroe County; 45, White clay deposits, central Pennsylvania; 47, Manganese, Eastern Pennsylvania, 48, Pyrite from bituminous coal mines; 59, Bog

Jan 1, 1933

By T. B. Counselman

"C" VERYONE who has to calculate cyanide circuits, -¦-&apos; using either thickeners, filters or both, realizes the headaches involved in solving a set of simultaneous equations. When you calculate a large number of these, based on experimental data, trying to arrive at the best flowsheet, you can spend days at the task. T. B. COUNSELMAN, Member AIME, is Manager, FluoSolids Division, The Dorr CO., Stamford, Conn. AIME New York Meeting, Feb. 1950. TP 2783 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Aug. 23, 1949. Herewith is presented a short method, equally accurate with the standard simultaneous equation method, and much quicker. Here for instance is the standard simultaneous equation method, for 100 tons per day of $10 ore, with the conditions assumed as below (fig. 1). Conditions Assumed a. 100 tons of ore per day crushed in cyanide solution. b. Discharge from all thickeners with 50 pct moisture. c. $10 value dissolved per ton of ore. d. 50 pct in mill and 50 pct in agitators. e. 400 tons of solution from thickener V precipitated to $0.02. f. Agitation with a dilution of 2 of solution to 1 of solids. g. Let V, W, X, Y and Z represent value in dollars per ton of solution discharged from the resvective thickeners. Equating Out of and Into Each Thickener 1. lOOVplus 400V = 500W plus (0.50 X $10 X 100) 2. 1OOWplus 600W= 500X plus lOOW plus (0.50 X $10 X 100) plus lOOV 3. lOOXplus 500X = 1OOWplus 500Y 4. 1OOY plus 500Y = 1002 plus 1OOX plus (400 X 0.02) 5. 100 Zplus l00Z = l00Y plus 100 tons of water (value $0.00) Simplifying: 1. v = W plus 1.00 2. W = X plus 1.20 3. X = Y plus 0.24 4. Y = 0.2Zvlus 0.064 5. 2Z= Y

Jan 1, 1951

By T. B. Counselman

"C" VERYONE who has to calculate cyanide circuits, -¦-&apos; using either thickeners, filters or both, realizes the headaches involved in solving a set of simultaneous equations. When you calculate a large number of these, based on experimental data, trying to arrive at the best flowsheet, you can spend days at the task. T. B. COUNSELMAN, Member AIME, is Manager, FluoSolids Division, The Dorr CO., Stamford, Conn. AIME New York Meeting, Feb. 1950. TP 2783 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Aug. 23, 1949. Herewith is presented a short method, equally accurate with the standard simultaneous equation method, and much quicker. Here for instance is the standard simultaneous equation method, for 100 tons per day of $10 ore, with the conditions assumed as below (fig. 1). Conditions Assumed a. 100 tons of ore per day crushed in cyanide solution. b. Discharge from all thickeners with 50 pct moisture. c. $10 value dissolved per ton of ore. d. 50 pct in mill and 50 pct in agitators. e. 400 tons of solution from thickener V precipitated to $0.02. f. Agitation with a dilution of 2 of solution to 1 of solids. g. Let V, W, X, Y and Z represent value in dollars per ton of solution discharged from the resvective thickeners. Equating Out of and Into Each Thickener 1. lOOVplus 400V = 500W plus (0.50 X $10 X 100) 2. 1OOWplus 600W= 500X plus lOOW plus (0.50 X $10 X 100) plus lOOV 3. lOOXplus 500X = 1OOWplus 500Y 4. 1OOY plus 500Y = 1002 plus 1OOX plus (400 X 0.02) 5. 100 Zplus l00Z = l00Y plus 100 tons of water (value $0.00) Simplifying: 1. v = W plus 1.00 2. W = X plus 1.20 3. X = Y plus 0.24 4. Y = 0.2Zvlus 0.064 5. 2Z= Y

Jan 1, 1951

By J. L. Walter

Extra-low carbon iron sheet, when deformed and annealed, undergoes exaggerated or abnormal grain growth in the critically deformed regions of the sheet. This exaggerated pmth occurs, for low strains (3 to 6 pct), only in sheet which has a fine dispersion of precipitates in the subsurface region of the sheet and fewer and coarser precipitates in the sheet interior. These particles have been identified as manganese sulfides. Wing the anneal, grains near the surface are gvowth-inhibited by the fine particles but the grains in the interior are free to grow normally. With the additional driving force provided by the strain energy, the interior grains first grow into the small subsurface pains. Eventually, these growing grains grow completely through the sheet. Calculations of limiting grain sizes at various values of strain indicate that a volume fraction of precipitates in excess of 10-&apos; would be required to eliminate exaggerated growth in material strained to 10 pct. OPEN-COIL annealing has made decarburization of sheet steel both efficient and economically practical. Use of such material for porcelain-enameling stock is one of many possible applications of low-carbon iron since carbon in steel is deleterious to porcelain-enameling properties.&apos; However, the extra-low carbon iron presently available presents another problem, that of exaggerated grain growth in regions where the sheet has been deformed as by bending or stretching. In exaggerated grain growth a few grains start to absorb their neighbors and these may become very much larger than the average grains of the sheet. Other names for exaggerated grain growth are coarsening, critical grain growth, secondary recrystallization, abnormal grain growth, or discontinuous grain growth. While this grain growth does not affect the enameling qualities of the low-carbon iron sheet, their presence results in a marked reduction of tensile-yield strength in the region of the sheet containing the large grains. The loss of tensile yield strength may render the material unsuitable for many applications . This report describes the results of a study undertaken to determine the cause of the exaggerated grab growth in extra-1ow carbon iron and, if possi- ble, to prescribe practical procedures for its prevention. GENERAL THEORY The driving force for exaggerated grain growth is the grain boundary free energy. This driving force is proportional to (l/rl + l/r2) where rl and r2 are the mutually perpendicular radii of curvature of the boundary between the growing grain and the grain being consumed. Thus, the greater the difference in size between the growing grain and the matrix grains, the higher the driving force for grain growth. If, however, the matrix grains are free to grow simultaneously, the driving force for exaggerated growth will be diminished. Stability toward growth of the matrix grains may be caused by a) a strong single orientation texture (texture inhibition),&apos; b) a dispersed second phase,3"5 c) the thickness effect,&apos; or d) intergranular segregation.7"9 As exaggerated growth occurs when growth of the matrix grains has been slowed by the stabilizing processes mentioned above, there must be an additional factor acting to promote growth of a few of the grains to the point where they are enough larger than the matrix grains that boundary energy driving forces are sufficient to cause continued growth. For instance, at the annealing temperature, growth-inhibiting inclusions may slowly dissolve and coalesce. Eventually, a grain boundary becomes unlocked and migration occurs at the expense of neighboring grains. Or, an additional driving force may be supplied to some of the grains if the material is strained. Then, since some grains will be strained less than others, the difference in strain energy between adjacent grains may be sufficient to overcome boundary locking and allow growth of the grains with lower strain energies. In the present study, therefore, such factors as the presence or absence of dispersed phases, the nature of the exaggerated growth, and the effect of strain have been considered. EXPERIMENTAL PROCEDURE I) Material and Processing. Three types of low-carbon iron were used in this study; types A and B were commercial grades, each from a different supplier.* The precise details of the processing of

Jan 1, 1963

By P. P. Gregory

The rate of drilling operations in the West Texas district during 1940 was approximately equal to that of 1939. The total number of wells dillled in the area during the year was 1834, of which 1716 were completed as oil producers, 12 were gas wells and 106 were dry holes. The number of wildcat wells drilled during the year was comparatively small. The drilling of inside locations in proven areas and the drilling of wells for the purpose of extending the productive limits in producing fields constituted the bulk of development during 1940. Gaines County led all other counties in the district in the total number of oil-well completions. The oil production totaled 83,345,381 bbl., the highest figure for any year since proration was begun. The 1940 oil production exceeded the 1939 production by approximately four million barrels. Discoveries While comparatively few new oil-producing areas were discovered during 1940, it appears that the oil production found in simpson lime in the Abell field, pecos County, was an outstanding discovery for the year. This was the second Ordovician discovery in Pecos County. Taubert, McKee & Siemoneit located its discovery well, V. W. Crockett No. 1, set. 4 1/2 H. & T. C. R.R, co, survey in the Imperial area of northwestern Pecos County. The top of pay was encountered at 5270 ft., and the well was bottomed at 5357 ft. in simpson lime, on act. 17, I940. The initial production was 928 bbl. of 43" gravity sweet oil in 11 hr. 23 min., flowing naturally through 2-in. tubing with gas-oil ratio of 783 cu. ft. per barrel. Following the completion of the discovery well, large blocks of land were leased in the area, and several locations were made toward the close of the year. There is every indication that the Abell field will become a major producing field in the West Texas district. There was no pipe-line outlet for the field at the end of the year. Shipley-Silurian field, discovered by the Gulf Oil Corporation, appears to be another major addition to the oil reserves in 1940. The discovery well, Wristen Brothers No. 5, is in sec. 18, block 5, H. & T. C. R.R. Co. survey in Ward County. The well was drilled to a total depth of 9187 ft. and was plugged back to 7075 ft. The Silurian lime section was acidized with 3000 gal., from 6993 to 7075 ft., and on Dec. 5, 1940, the well was completed for initial production of 3040 bbl- of 32.2" gravity oil in 24 hr., flowing through tubing. Todd Deep field, Crockett County, was discovered by the Continental Oil Co. et al. The discovery well, J. S. Todd No. 2, set. 29, block WX1 G.C. & S.F. R.R. Co. survey, was completed on April 3, 1940. The top of pay was encountered at 5623 ft., and the well was bottomed at 5691 ft. for initial production of 1613 bbl. of 40.6&apos; gravity oil flowing naturally through 2-in. tubing. The pay section was found in Strawn lime of Pennsylvanian age. There were six producing wells in the field at the end of the year. This appears to be another major discovery in 1940. There was no pipe-line outlet in the field at the end of the

Jan 1, 1941

By P. P. Gregory

The rate of drilling operations in the West Texas district during 1940 was approximately equal to that of 1939. The total number of wells dillled in the area during the year was 1834, of which 1716 were completed as oil producers, 12 were gas wells and 106 were dry holes. The number of wildcat wells drilled during the year was comparatively small. The drilling of inside locations in proven areas and the drilling of wells for the purpose of extending the productive limits in producing fields constituted the bulk of development during 1940. Gaines County led all other counties in the district in the total number of oil-well completions. The oil production totaled 83,345,381 bbl., the highest figure for any year since proration was begun. The 1940 oil production exceeded the 1939 production by approximately four million barrels. Discoveries While comparatively few new oil-producing areas were discovered during 1940, it appears that the oil production found in simpson lime in the Abell field, pecos County, was an outstanding discovery for the year. This was the second Ordovician discovery in Pecos County. Taubert, McKee & Siemoneit located its discovery well, V. W. Crockett No. 1, set. 4 1/2 H. & T. C. R.R, co, survey in the Imperial area of northwestern Pecos County. The top of pay was encountered at 5270 ft., and the well was bottomed at 5357 ft. in simpson lime, on act. 17, I940. The initial production was 928 bbl. of 43" gravity sweet oil in 11 hr. 23 min., flowing naturally through 2-in. tubing with gas-oil ratio of 783 cu. ft. per barrel. Following the completion of the discovery well, large blocks of land were leased in the area, and several locations were made toward the close of the year. There is every indication that the Abell field will become a major producing field in the West Texas district. There was no pipe-line outlet for the field at the end of the year. Shipley-Silurian field, discovered by the Gulf Oil Corporation, appears to be another major addition to the oil reserves in 1940. The discovery well, Wristen Brothers No. 5, is in sec. 18, block 5, H. & T. C. R.R. Co. survey in Ward County. The well was drilled to a total depth of 9187 ft. and was plugged back to 7075 ft. The Silurian lime section was acidized with 3000 gal., from 6993 to 7075 ft., and on Dec. 5, 1940, the well was completed for initial production of 3040 bbl- of 32.2" gravity oil in 24 hr., flowing through tubing. Todd Deep field, Crockett County, was discovered by the Continental Oil Co. et al. The discovery well, J. S. Todd No. 2, set. 29, block WX1 G.C. & S.F. R.R. Co. survey, was completed on April 3, 1940. The top of pay was encountered at 5623 ft., and the well was bottomed at 5691 ft. for initial production of 1613 bbl. of 40.6&apos; gravity oil flowing naturally through 2-in. tubing. The pay section was found in Strawn lime of Pennsylvanian age. There were six producing wells in the field at the end of the year. This appears to be another major discovery in 1940. There was no pipe-line outlet in the field at the end of the

Jan 1, 1941

By Robert W. Hendricks, John B. Newkirk

A simple method is described for determining the orientation of a single crystal by means of a cylindr cal X-ray camera. Orientation setting to within ±1 deg is attainable by a stereographic analysis of a single cylindrical Laue pattern produced by the originally randomly mounted crystal. Final precision adjustments which permit orientation of the crystal to within ±5 min of arc from the desired position can be made by the method of Weisz and Cole. A chart, originally Presented by Schiebold and schneider7 and which allows a direct reading of the two stereographic polar coordinates of the corresponding pole of a given Laue spot, has been recomputed to aid in the stereographic interpretation of the cylindrical Laue X-ray photograph. Detailed instructions for the use of the chart, a simple example, and a comparison with the conventional flat-film Laue Methods, are presented. 1 HE problem of determining the orientation of the unit cell of a single crystal relative to a set of fixed external reference coordinates is fundamental to most problems of X-ray crystallography and to many experimental studies of the structure-sensitive physical properties of crystalline materials. Several techniques for measuring these orientation relations have been developed which correlate optically observable, orientation-dependent physical properties to the unit cell. Examples of such procedures include the observation of cleavage faces or birefringence, as discussed by bunn,1 or the examination of preferentially formed etch-pits, as discussed by barrett.2 Each of these methods is limited, for various reasons, to an orientation accuracy of approximately ±1 deg—a serious limitation in some experimental studies. Several other limitations decrease the generality of these methods. Of these, perhaps most notable is the absence in many crystals of the physical property necessary for the orientation technique. The most widely used methods for determining crystal orientation are variations of the Laue X-ray diffraction method. Because of the indeterminacy of the X-ray wavelength diffracted to a given spot, the interpretation of Laue photographs is now limited almost exclusively to the procedure of using a chart to determine the angular coordinates of the corresponding pole for each spot. For the flat-film geometries, either a leonhardt3 or a Dunn-Martin4 chart is used in interpreting transmission patterns, whereas a greninger5 chart is used for interpreting back-reflection patterns. A less common method of interpreting flat-film transmission Laue photographs is by comparing the Laue pattern with the Majima and Togino standards,6 or with the revised standards prepared by Dunn and Martin.4 Although this last method is applicable only to crystals with cubic symmetry, it can be very rapid and just as accurate as the graphical methods. The primary limitation of all the X-ray methods mentioned is the relatively small number of Laue spots and zones which are recorded on the flat film. Often, few, if any, major poles appear, thus making interpretation tedious and sometimes uncertain. The use of a cylindrical film eliminates this problem. Schiebold and schneider7 prepared a chart by which the orientation of the specimen crystal could be determined from a cylindrical Laue photograph. However, it was only drawn in 5-deg intervals of each of the two angular variables used to identify the Laue spots, thus limiting the accuracy of orientation to about ±3 deg. An examination of this chart indicated that if it were drawn in 2-deg intervals, crystal orientations to ±1 deg would be attainable. Subsequent use of the replotted chart has confirmed this accuracy. It is the purpose of this paper to describe the redevelopment and use of this chart, and to point out its advantages and limitations. I) CAMERA GEOMETRY AND CHART CALCULATIONS The geometry of the cylindrical camera with a related reference sphere is shown in Fig. 1. The X-ray beam BB&apos; pierces the film at the back-reflection hole B, strikes the crystal at 0, and the transmitted beam leaves the camera at the transmission hole T. One of the diffracted X-rays intersects the film at a Laue spot L. The normal OP to the diffracting plane bisects the angle BOL between the incident and diffracted X-ray beams. The point P on the reference sphere can be located uniquely by the two orthogonal motions 6 and 8 on the two great circles ENWS and BPQT respectively. Because the Bragg angle 8 (= 90 - < BOP) is always less than 90 deg, P always remains in the hemisphere BENWS. Therefore, if every possible pole P is to be recorded on the same stereographic projection, it is necessary that the projection reference point be at T with the projection plane tangent to the sphere at B.* The great

Jan 1, 1963

By J. L. Bruce, G. W. Nicolson

THE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydrothermally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CEMENT AND CONCRETE LININGS During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, however, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 1 ½ pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with I2 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concrete and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1947

By P. Ramachandrarao, T. R. Anantharaman

EVER since the technique of quenching metals and alloys from the melt (splat cooling) was perfected a decade ago, it has been recognized that the grain size of products solidified by this technique may be extremely small.&apos; The further observation that fcc metals quenched from the liquid state contain very few dislocations has led to the inference2 that metals are subjected to negligible or no stresses during the rapid solidification characteristic of the "gun" or "piston-and-anvil" technique. Evidence for the incidence of appreciable densities of stacking faults has, however, been obtained in case of some splat-cooled fcc and hcp alloys,3 although not for pure metals. In the light of these earlier observations it was considered desirable to study X-ray line-broadening effects, if any, in fcc metals rapidly cooled from the melt. In the present work pure silver (>99.99 pct), aluminum (>99.99 pct) and lead (>99.9 pct) were quenched from the liquid state from temperatures about 50°C above the melting point by the "gun technique" and the resulting foils were subjected to X-ray examination in a Philips Diffractometer. The quenched foils (up to -10 u thick) did not generally stick to the substrate surface and could be easily transferred to the Diffractometer without introducing any plastic deformation. The profiles of the first five reflections from the foils were recorded in each case with Cu Ka, radiation at the slowest available scanning speed of 1/8 deg per min. To correct for instrumental broadening, profiles were also recorded from the metals annealed in vacuo at suitable temperatures. The integral breadths of the X-ray reflections were arrived at by a procedure described earlier.&apos; There was a distinct suggestion of preferred orientation in the recorded intensities of reflections from aluminum and lead foils. Such an effect was not observed in case of silver. In addition, the integral breadths of X-ray reflections from splat-cooled aluminum and lead were not significantly different from those recorded for the annealed metals. The analysis was therefore continued only for silver where the X-ray line broadening was appreciable. The pure diffraction broadening, B, was evaluated for each X-ray reflection (hkl) from silver from the observed, B, and instrumental, b, breadths with the aid of each of the three equations due to Scherrer,5 Anantharaman and Christian,6 and Warren and Biscoe,7 respectively: Bs= B-b BAC=B- b2/B Table I gives the values of particle size, 71, the lattice strain, E, arrived at by the use of the following well-known relations and on the assumption that all observed diffraction broadening could be attributed to lattice strain or particle size, respectively: E = 1/4 cos ? n= B cos ? where A is the wavelength of X-radiation and 0 is the Bragg angle. As no significant peak shifts or asymmetry could be detected in the profiles from the foils, the possibility of any significant contribution due to twins or stacking faults was ruled out. The absence of faults is by no means surprising since pure silver is known to develop stacking faults only on severe deformation and the stacking fault densities recorded so far for even silver filings have been extremely low.&apos; The very low values for percentage mean deviation from the mean value for the particle size in Table I strongly suggest that all observed broadening in splat-cooled silver can be attributed only to small particle size. This conclusion receives further support from the lowest mean deviation recorded for data computed from the Scherrer equation based on Cauchy profiles that are considered characteristic of particle size broadening. Further analysis for separation of particle size and lattice strain effects was considered unnecessary in view of the very large mean deviations obtained for strain values and also the earlier results suggesting absence of even detectable strain in metals and alloys quenched from the melt. It is to be stressed in this connection that the particles are actually grains and not cells formed by walls of high dislocation density usually encountered in deformed samples. As such, the absence of strains is not surprising. The present results are probably the first to record X-ray line broadening due only to small particle

Jan 1, 1970

By B. H. Kear, H. G. F. Wilsdorf

After a few percent strain, dislocations in disordered Cu3Au are arranged in groups in ulell-defined slip planes, which contrasts with the more or less random distribution of dislocations in the corresponding ordered alloy. Unusually long and straigkt dislocation segments observed in the ordered alloy are interpreted in terms of cross slip of screw dislocations from their slip planes into cube planes. It is proposed that cross slip, and also dislocation reactions of the Lomer type, play an important role in work hardening of the ordered alloy. ACCORDING to to dislocations in the disordered lattice are only partial dislocations in the corresponding super lattice, so that in the super-lattice dislocations must occur as pairs, with each pair connected by a ribbon of antiphase boundary. Recently, striking confirmation of the theory was obtained by Marcinkowski, Brown, and Fisher3j4 in a study of dislocation configurations in thin foils of the Cu3Au alloy by transmission electron microscopy. In the present investigation, the observations made by these workers have largely been confirmed. Moreover, it has been found that dislocations in the plastically deformed ordered alloys are often unusually long and straight. This paper is mainly concerned with these new observations. A tentative explanation is offered in terms of cross slip of dislocations in the ordered alloys. PREPARATION OF SPECIMENS An alloy close to the stoichiometric composition Cu3Au was prepared by melting together high-purity copper and gold (99.995 pct) under vacuum in a graphite mold. The resulting ingot was rolled down and cut into strips 1 1/2 by 1/8 by 0.005 in. in thickness. All strips were annealed at 900°C for 3 hr and cooled to 500&apos;~. A few of the strips were quenched from ~OO&apos;C, while the remainder were slowly cooled in the temperature range 400" to 150°C at intervals of a few degrees every 24 hr to produce a high degree of order. After this annealing treatment the average grain size of the material was about 0.1 mm. Material in different states of order was obtained by reannealing fully ordered material at temperatures below the critical temperature: followed by quenching. The equilibrium degree of order attained at a particular reannealing temperature was obtained from the paper by Keating and warren.&apos; A simple hand-operated tensile jig was used to give the strips the required amounts of plastic strain. Following straining, a number of specimens were cut from each strip by means of an electrolytic cutting device.= Finally, each specimen was thinned electrolytically using the polishing procedure described by Bakish and Robertson,7 and these thin sections were examined in the Philips EM-100B electron microscope operating at 100 kv. EXPERIMENTAL OBSERVATIONS Antiphase boundaries. The average domain size in the ordered alloys was found by direct observation to be about 0.25 p. Also, it was observed that the grown-in configuration of antiphase boundaries was changed little by plastic deformation, at least up to 6 pct strain. Fig. 1 shows an electron micrograph of a thin foil of partially ordered alloy (S - 0.8) after 3 pct strain. The micrograph shows a few dislocation pairs and a somewhat crystallo-graphic network of antiphase boundaries. The normal to this foil was found by diffraction analysis to be approximately 11121, with principal directions in

Jan 1, 1962

By R. Buehl

ALTHOUGH the main features of the transformations occurring in 18-8 have been published already,1-4 certain conclusions merit questioning and discussion. The questions may be summarized as follows: PERCENT REDUCTION BY COLD ROLLING FIG. 1.-VARIATION OF FERRITIC INDUCTION AND PERCENTAGE OF FERRITE WITH COLD REDUCTION. Composition of Alloy: C, 0.08; Mn, 0.40; Si, 0.24; P, 0.014; Cr, 18.13; Ni, 8.94. 1. If ferrite is formed by cold-working austenite, what happens to the carbon with which the ferrite and austenite are both pre-sumably supersaturated? 2. What is the nature of the alpha-ferrite formed at grain boundaries by chromium-carbide precipitation at these boundaries?

Jan 1, 1939

By LESTER H. WOOLSEY

IT IS doubtful whether anything new can be said upon this subject and, therefore, it is with considerable hesitation that l prepare this paper. On account of my recent connection with the Department of State as its law- officer, perhaps I will be pardoned if I discuss this subject briefly from the point of view of that branch of the Government. , I cannot, of course, speak for that department, since I have-no connection with it at-present, but it may be helpful if I set down certain* of the factors which in my opinion and from my experience have a bearing on this international problem. With oil-burning ships, motor vessels, motor vehicles, airplanes-all consuming, astonishing quantities of petroleum or petroleum products; with the United States having within its borders only 12 per cent. of the petroleum resources of the world, and consuming about 70 per cent. of the world&apos;s output; with the more enterprising nations wide awake to the necessity ; of obtaining and preserving as large a share as possible of the oil resources extant ; the &apos;problem is peculiarly and in a, very practical sense an international one.

Jan 1, 1921

By D. I. Bardos, Paul A. Beck

The 1100°c isothermal, sections of the V-Fe-Si, V-Co-Si, and V-Ni-Si systems were studied at silicon contents between 0 and 40 at. pct. The single-phase fields in the 30 and 50 at. pct Mn sections of the 1100°C tetrahedron of the V-&apos;Wn-Fe-Si system were also determined. The direction of extension of the elongated O, R, D, and a-Mn Phase fields suggests that the stability of these phases is determined largely by the electron concentration. The peculiar shape of the above ternary a phase fields, as well as of the a phase fields in the V-;Mn-Si and Cr-MTZ-Si systems is accounted for on the assumption that in manganese-(iron-, coball-, nickel-) rich alloys silicon atoms do not exclude d electrons , while in alloys low in the above components they do. This assumption also leads to the expected electronconcentrations for q and ß-Mn phases formed by transition metals with aluminurn. In earlier work it was shown that in ternary alloy systems of transition elements the a a and certain other phases with complex structure, such as the p and R phases,3 form elongated phase fields extending in a direction corresponding to a constant electron concentration. Recently similar behavior was observed in manganese-rich ternary ß-Mn solid solutions with another transition element and with silicon, germanium, or tin,4 confirming earlier indications3 that ß-Mn is also an electron phase. The alloying behavior of silicon in these manganese-rich alloys sug- gested that the four outside electrons of silicon participate in the bonding and that the predominantly d-like bonding electrons are not excluded from the silicon sites. Presumably, some of the normally unoccupied 3d states associated with the silicon atoms are in these alloys lowered to the Fermi level;4 thus silicon behaves as if it, too, were a transition element. The manganese-rich boundary of the a phase in the V-Mn-Si system,4 as well as in the Cr-Mn-Si sys-tem,4,5 extends approximately parallel to the ß-Mn phase boundary, corresponding to the transition ele-mentlike behavior of silicon described above. However, at lower manganese contents (i.e., in the high-vanadium or -chromium region) the a phase field in both ternary systems mentioned extends in a direction roughly perpendicular to that of its manganese-rich boundary, a phenomenon that is apparently inconsistent with the behavior of silicon in the manganese-rich alloys. A similar, although somewhat less pronounced, extension of the a phase occurs also in the high-vanadium (low-iron) region of the V-Fe-Si system at 1175C, but reportedly not in the V-Co-Si or V-Ni-Si systems at the same temperature.5 The present work was undertaken to investigate in more detail the extension of the a phase (as well as of other electron phases that may be present) in the last three systems and to elucidate this phenomenon, which has not been satisfactorily explained previously. EXPERIMENTAL PROCEDURES Most of the alloys were melted in an arc furnace, using a water-cooled copper crucible under helium atmosphere. The transition metals were of better than 99.9 pct purity and the silicon used was 99.98 pct pure. Alloys containing less than 20 pct V were induction-melted in recrystallized alumina crucibles under argon atmosphere.

Jan 1, 1967

By W. A. Olds, H. F. Yancey, M. R. Greer

John Griffen (Consulting Engineer, Pittsburgh)— This paper presents much data offering tentative answers to many technical questions that have been raised by the employment of dense-medium processes and, particularly. by use of the drum-type vessel. It is to be hoped that the Bureau of Mines will publish complete detailed data for the 50 or more tests so that it may be studied and analyzed by everyone interested. Such study will take considerable time and effort. The writer is therefore obliged to confine his discussion to a few points he has noted as being open to question. The data in Table VI which shows the recovery efficiency for the 1 to ½-in. fraction as 100 pct raised a question concerning the accuracy of these calculated figures; washability data on the washed coal and refuse show that such a figure is impossible. When the ash content of the misplaced material in the washed coal is higher than that of the misplaced material in the refuse, recovery efficiency must be less than 100 pct. A etudy of the data In Tables 111, IV, V, and VI suggest that this error probably arose from slight errors in calculating the data in Table V and more probably from the small scale used in plotting the washability curves from the Table V data. Using the size consist data and the weight and ash percentages of individual gravity fractions of each size as given in Tables 111 and IV and the reported recovery of 80 pct of washed coal, a revised Table V was calculated, carrying weight and ash percentages to hundredths of a percent instead of rounding off at tenths. This washability data for each size of Belling-ham reconstituted feed was then plotted on large scale washability curves. From this data the new Table XIV was prepared, which agrees very closely with data shown in Table VI except for two important values, theoretical yields and recovery efficiencies. As will be noted the recovery efficiencies in Table XIV are significantly lower than those given in Table VI. A study was then made of the data showing distribution of the specific gravity fractions to washed coal and refuse. This study indicated that when this distribution was based on the fractions as tested at 0.1-sp gr intervals the number of points obtained were insufficient to establish the distribution curves with reasonable precision, which in turn would affect the accuracy of the values for the specific gravity of separation and the error areas. The data in Tables III and IV of the paper and curves prepared therefrom make it possible for the specific gravity fractions to be subdivided further. This was done using 0.05-sp gr fractions and the distribution data so obtained is given in Table XIV, with resulting values for the specific gravity of separation and the error areas. The writer believes that the derived values shown on Table XIV are more accurate than the correspond-

Jan 1, 1955

By E. N. Harshman

The Wind River Formation of Eocene age is the host rock for large high-grade uranium deposits in the Shirley Basin. The major deposits are in a northwest-trending belt of sandstones that were deposited in stream channels and that were lithologically favorable for uranium accumulation. Paleotopography influenced the character and position of the belt. The major deposits within the belt are at, or near, the margins of large tongues of altered sandstone formed in the most transmissive parts of thick sandstone beds. At least two tongues of altered sandstone are present in the belt, one of which is 5 miles long, 3 miles wide, and 70 feet thick; the other tongue is somewhat smaller. Ore bodies consist of a few hundred tons to several hundred thousand tons of material containing from 0.10 to about 2.00 per cent U3O8. The ore mineral is uraninite associated with pyrite, marcasite, hematite, and calcite. Deposition is believed to have taken place when neutral to slightly alkaline, oxidizing, uranium-bearing ground water, on entering the basin, encountered a reducing environment. The reductant may have been H2S of biogenic origin. Geology played an important role in discovery, exploration, and development of ore in the Shirley Basin.

Jan 1, 1968

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200°C, a wide range of conveyors is available. Special constructions of rubber conveyor belts. steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400°F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F.

Jan 5, 1953