Search Documents

By A. Phillips, D. H. Killpatrick, V. Kerlins

The tensile failure of two dispersion-strengthened Ni-20 Cr alloys was studied and compared to the fracture of a similar alloy with no dispersoid. The fracture characteristics were studied using electron fruc-tography and transmission electron microscopy. In all three cases, the mode of failure was found to be microvoid coalescence. The failure in the dispersion-strengthened alloys was found to have initiated at the particles. The size of the dimples in the fracto-graphs was found to be related to the spacing of the particles, but not to the total elongation before failure. The elongation before failure was found to be related only to the amount of dispersed phase. These results are compared to those predicted by a theoretical model of ductile failure. THE continually increasing strength requirements for creep-resistant materials capable of long life at service temperatures above 1600"F (875"C) have developed considerable interest in dispersion-strengthened nickel-base alloys. The high yield strength of these alloys results from the presence of a dispersion of fine particles of thoria which act to impede the normal motion of dislocations. Many theories have been presented to explain the role of the dispersion in the strengthening of these alloys. A good review of these theories is presented by Ansell.' The ultimate strength of such alloys is not only related to mechanisms raising the yield strength, but also to the amount of work-hardening which occurs. This work-hardening is determined by the work-hardening rate and the amount of plastic strain before failure. Since fracture limits the amount of plastic strain, a study was undertaken to gain a better understanding of the fracture mechanisms in these alloys. Electron fractography and transmission electron microscopy were used to study the fracture characteristics in two dispersion-strengthened alloys and one similar alloy containing no dispersoid. These results are related to the tensile properties of the dispersion-strengthened alloys at room temperature and at 2000°F (1095°C). The results are also related to a theory for ductile fracture. 1) PROCEDURE Standard tensile specimens were made from 0.020-in. (0.051-cm) sheets of three different Ni-Cr alloys. The alloys had nominal compositions of Ni-20Cr, Ni-20Cr-2Th0,, and Ni-2OCr-4Th0,. All alloys were supplied in an annealed condition. The specimens were fractured in tension at room temperature to determine the effect of the dispersed thoria on the fracture appearance. The tensile properties were determined from the average of a minimum of three ten- sile specimens for each condition tested. The fracture surface of all of the alloys was examined by electron microscopy using standard two-stage plastic-carbon replica techniques. Thin foils of the dispersion-strengthened alloys were used to investigate the size and spacings of the dispersion particles, and to investigate sections of the 2 pct thoria alloy taken from areas of the specimen adjacent to the fracture surface. The thin foils were mechanically ground to 0.010 in. (0.025 cm) and then chemically polished to approximately 0.001 in. (0.003 cm) in a solution of 29 g of ferric chloride and 10 ml hydrochloric acid in a liter of water. The polishing solution was maintained at 150"F (65°C) during the thinning operation. The final thinning of the foil was done electrolytically using a solution of 700 ml ethanol, 100 ml 2-butoxy eth-anol, 120 ml distilled water, and 78 ml perchloric acid (70 pct). The potential was maintained at 15 v and the bath temperature at -20°~ (-29°C) during the thinning operation. The final thickness of the foil was approximately l000A as determined from the width of twins boundaries observed in many of the foils. 2) RESULTS AND DISCUSSION The electron fractographs of the fracture surfaces of the alloys are shown in Figs. 1, 2, and 3. The normal interpretation of this type of fractographz is that, as a result of the difference between elastic and plastic properties of the matrix and the particles or other inhomogeneities in the alloy, microvoids are formed

Jan 1, 1969

By Charles Barron McIntosh

BECAUSE of the well known relationship between a low atmospheric pressure and increased amounts of methane in coal mines, attempts have been made to find associations between low pressures and coal mine explosions. An early study by F. Able disclaimed this relationship. He found that half the explosions took place during a rising barometer when methane content in a ventilated mine would be decreasing. A more recent study by C. L. Hosler revealed a close relationship between anthracite mine explosions and low atmospheric pressure. Bituminous coal mine explosions, where coal dust as well as methane can be exploded, were found to be more closely associated with a rising pressure following a low barometer than with the falling or low pressure period. Emphasis on rising pressure periods led the present writer to investigate the effect of the post-frontal or post-cyclonic weather on coal dust. Dust samples of uniform mesh were exposed in an Illinois mine. Analyses of the dust taken before and after the passage of cold fronts and their accompanying low pressure troughs indicated an increase in coal dust moisture prior to a frontal passage and loss of moisture from coal dust following the time of lowest pressure. Thus the warm, moist air (Tropical Maritime)found over the mine during the falling pressure period was cooled in the mine and moisture added to the dust. Cold, dry air (Polar Continental) accompanies' the rising barometer following a frontal passage and the air, being heated in the mine, subtracted moisture from the coal dust. A similar but seasonal phenomenon occurs from summer to winter, the dry dust period in winter being recognized as the more dangerous period. The question arose as to how the short period or daily changes in moisture content of coal dust compared with the seasonal changes. Temperature and humidity statistics were obtained from the surface and mine entry for the months of July andJanuary. The gain and Ioss of mdisture. to the hine were calculated for these two morths as were the gain and loss associated with mT (Tropical Maritime) and cP (Polar Continental),air masses as observed in the investigatiynsl. Temperature and humidity statistics tigatiynsl.taken from [the two air masses represent atimp span of only 34 hr. The redultant changes as presented in the accompanying table verify the supposition that short period changes in coal mine moisture may attain the magnitude of recognized dangerous seasonal changes. Statistics for the mT air and the July air have been placed next each other and those for cP and January air together for easier comparison of the two warm and two cold air units. The last column readily reveals that there is little difference in the amount of moisture being deposited in the mine from the mT air and the July average air. A similar conclusion is reached regarding the loss of moisture from the mine when it is affected by the cP air mass or the average January air. This comparison would be particularly true from late fall through early spring when strongly contrasting air mass changes are a common occurrence. The invasion of cold, dry air following a cold front thus produces a drying period that could well receive more attention as a danger period for coal dust explosions. This drying period would compare with Able's explosion period during a rising barometer. The drying period is also perltinent in Hosler's findings, where it was noted that the average explosion day (for bituminous coal mines) followed the day of lowest atmospheric pressure. Moreover, the author's investigation of some 365 coal mine explosions also indicates that this post-frontal period should receive special attention in connection with mine safety measures. Two comparatively recent major explosions in Illinois (Centralia and West Frapkfort) occurred after the mines had been under the influence of cold-dry air for 25 to 30 hr-following a deep low pressure passage. Dust was the important explosive element in both these explosions.

Jan 1, 1958

By A. A. Watts, R. I. Jaffee, F. C. Holden, H. R. Ogden

Hypoeutectoid Ti-Cu alloys are responsive to heat treatment, and considerable variation of mechanical properties may be produced by transformation of the ß phase. Control of cooling rate, isothermal transformation, or quench tempering determine the transformation structure and properties. The transformation products are similar to those of carbon steel. THE equilibrium diagram for the Ti-Cu system has been studied by various investigators, and the most recent diagram is that determined by Jou-kainen, Grant, and Floe.' The titanium-rich portion of this diagram is reproduced in Fig. 1. The alloy compositions and annealing temperatures used in this work are shown. The Ti-Cu alloys containing up to 17 wt pct Cu are representative of an active eutectoid alloy system. Joukainen et a1.l have stated that ß phase cannot be retained on quenching and this has been confirmed in the present work. The similarity between the Ti-Cu system and the Fe-C system is evident and, as will be shown later, many of the transformation products appear to have similar microstructures. Heat treatments in this program were designed to produce the structures of primary interest for study and determination of mechanical properties. Experimental Procedures Preparation of Alloys: Five ½ lb ingots, ranging in composition from 0.8 to 6.83 pct Cu, were prepared by double arc melting in an atmosphere of high purity argon. Titanium melting stock was obtained from high purity iodide titanium, and copper additions were made from copper wire clippings. Segregation was reduced by inversion melting, in which the once-melted ingots were inverted in the crucible and remelted. The double-melted ingots were forged at 1600°F to ¾ in. diam rods, with both heating and forging operations being carried out in air. Surface scale was removed by grit blasting and grinding, after which the forgings were vacuum annealed at 900°C. The alloys then were swaged to ¾ in. diam rod at 750°C and test specimens were cut from this material. The vacuum annealing operation was to remove dissolved hydrogen, which is commonly present in the iodide titanium as-received. Although vacuum fusion analyses were not obtained for all these alloys, past experience indicates that the 6 hr treatment with a limiting pressure of 10- to 10-5 mm of Hg is sufficient to reduce the hydrogen level to 10 to 30 ppm. Vacuum fusion analysis of the 0.8 pct Cu alloy showed 19 ppm of hydrogen. In addition to the five hypoeutectoid alloys, three 15 g ingots were prepared with nominal copper additions of 9, 10, and 11 pct. Fabrication procedures were similar, except that these alloys were rolled to 0.040 in. sheet. Microstructure specimens only were obtained. Table I shows analyzed compositions and fabrication temperatures for these alloys. Heat Treatments: All heat treatments were made in potentiometer-controlled, resistance-wound tube

Jan 1, 1956

Table

Jan 1, 1910

By H. S. Drinker

THE first discovery of zinc 011 the property now worked by this company was made by the celebrated mineralogist, Prof. William Theodore Rapper, in 1845. Different claimants kept the property in continual litigation till 1861, when everything was satisfactorily settled by the purchase of the land by the company, who have worked it ever since. The mines are situated in a valley, four miles south of Bethlehem, Pa., in Lehigh County. The valley is from two to three miles broad, and is bounded 011 the north and south by syenitic hills. Syenite underlies the valley, and upon this is deposited the Potsdam sandstone, then a layer of slate, and, finally, a dolomitic limestone, belonging to the Chazy or Black River formation, in which the zinc deposits are inclosed. The rocks occur in folds, and have evidently been subjected to tremendous pressure from below, the zinc deposit being found in an anticlinal axis, in nearly vertical veins. I t is supposed that the zinc was originally disseminated through the

Mining headlines in 1952 dealt mainly with expansion as the industry aimed for an ever increasing production to meet the nation's needs. Huge sums were expended for equipment, research, and development. Headlines told part of the story. Negotiations between San Manuel Copper Co. and the RFC finally resolved in a $94 million loan for the development of low grade Arizona ores. Magma Copper, parent firm was to supply an additional 8 million. Kennecott Copper Co., deepening its Deep Ruth Shaft of its Ruth, Neyy mine, announced that the shaft would be in full production in 1953.

Jan 2, 1953

By E. M. MacKevett

The only source of uranium ore in Alaska that has been mined commercially is the Ross-Adams de- posit, a gently inclined, fusiform orebody in alkali granite in which uranothorite and uranoan thorianlte are the chief ore minerals. In mode of occurrence, apparent genetic association with the granite, and to a lesser extent in mineralogy, this type of deposit is uncommon. The mine is in the southern part of Prince of Wales Island (Fig. 1) at an altitude of about 950 ft on the southeast flank of Bokan Mountain. A steep unpaved road 1 ¾ miles long leads to the dock on the West Arm of Kendrick Bay, which can be reached by boat or seaplane from Ketchikan, some 35 miles to the northeast.

Jan 9, 1959

By E. P. Pfleider, E. G. Malmlow, F. Landau

Friction drive hoists, long popular on the Continent, are now being installed in the U. S. and Canada by the Swedish firm of ASEA. Invented by C. F. Koepe and used first in 18.77, the principle is the same as that in elevator installations throughout the world. Inherent advantages of this system of hoisting were not fully developed until the recent introduction of the multiple-rope principle and design of concrete tower installations. Operators have a choice of independent operation of single skips and cages using counterweights, or use of skips or cages in balance. Also, hoisting control may be automatic, push button, or manual.

Jan 1, 1955

By C. F. Tolman

In February 1913, Prof. L. C. Graton and Dr. Joseph Murdochl presented to the American Institute of Mining Engineers a notable contribution to economic geology under the title The Sulphide Ores of Copper. The value of the work was recognized by mine operators, and Mr. Graton was assisted in his plan to extend his investigations, by the organization of a commission to undertake a "secondary enrichment investigation." In this work he secured the cooperation of the Geophysical Laboratory of the Carnegie Institution of Washington. The report2 on the chemical phascs of the investigation has just been published. Incidental to investigations3 carried on in our laboratory of Economic

Jan 1, 1916

By F. H. Daniels

IN this, paper it is my intention to, call your attention to* a few of the many producers using blast, now, in common use in Sweden, and also those constructed by the Washburn & Moen Manufacturing Company at their Quinsigamond Works. During a prolonged stay in Sweden the writer had an opportunity

Jan 1, 1881

By C. F. Jr. Tolman

IN February 1913, Prof. L. C. Graton and Dr. Joseph Murdoch1 presented to the American Institute of Mining Engineers a notable contribution to economic geology under the title The Sulphide Ores of Copper. The value of the work was recognized by mine operators, and Mr. Graton was assisted in his plan to extend his investigations,. by the organization of a commission to undertake a "secondary enrichment investigation." In this work lie secured the cooperation of the Geophysical Laboratory of the Carnegie Institution of Washington. Their report 2 on the chemical phases of the investigation has just been published. Incidental to investigations 3 carried on in my laboratory by advanced

Jan 2, 1916

By Shuichiro Okada

The Tamano Smelter, which is engaged in copper smelting by Flash Smelting Furnace with Furnace Electrodes (FSFE) has since 1982 revised its computer and associated control system for the purpose of greater energy savings, stable operation, and strict environmental control. This revision is bringing about a remarkable cost savings through greater reduction in energy consumption. This paper describes in detail the following: (a) outline of renewed process computer system, (b) approach to prediction model of FSFE based on data collection and its analysis, (c) actual examples of process control by using its prediction model, (d) future trends in the computer control at Tamano Smelter.

Jan 1, 1984

By C. L. Meyers, J. L. Lytton, T. E. Tietz

The recovery of tensile flow stress of 99.995-pct Al and Al-1 pct Mg alloy was investigated using a fractional recovery parameter. Tensile strainirg was conducted at room temperature, and recovery treatments were made in the range from 80° to 200°C. Equal values of fractional flow stress recovery were found to result in equivalent structural states. Identical recovery treatments were found to produce constant values of fractional flow stress re covery, independent of prestrain. The activation energy for recovery of the 99.995-pct A1 between 80" and 200°C was found to be 23,000 +2000 cal per mole, and the activation energy for the Al-1 pct Mg alloy was 27,500 cal per mole. 1 HE degree of recovery of a cold-worked metal may be studied by measuring the changes which take place in any of a number of properties. Some of the properties which have been used by past investigators include X-ray diffraction phenomena, electrical resistivity, hardness, creep strength, elastic limit, and flow stress. Despite the apparent preponderance of such studies, little is known concerning the effect of recovery on the strength of metals except as deduced from changes in various types of hardness measurements. Furthermore, little information is avail- able concerning the effects which specific solute atoms have on the recovery process. Limited studies have indicated that in some cases solid-solution additions greatly decrease the rate of recovery,' whereas in at least the case of magnesium additions to alluminum an increase in the rate has been reported.2 The purpose of this investigation was to determine the effect of a 1 pct Mg addition on the recovery of high-purity aluminum. Because of the particular interest in the effect of solute additions on the recovery behavior as related to mechanical properties, the degree of recovery was evaluated in terms of tensile flow stress. For the purposes of this study, a recovery process shall be defined as any process, short of recrystallization, whereby the properties, of work-hardened metals tend toward their values ill the unstrained state. EXPERIMENTAL PROCEDURE Test Materials. The materials used in this study were a 99.995-3 A1 and an Al-1 pct Mg alloy made from high-purity base metal. The high-purity aluminum contained the following wt pct impurities: 0.001 pct Cu, 0.002 pct Fe, 0.001 pct Si, and 0.0004 pct Mg. The Pil-1 pct Mg alloy contained 0.001 pct Cu, 0.002 pct Fe, 0.003 pct Si, and 0.99 pct Mg. Both materials were obtained in the form of as-rolled 0.125-in.-thick sheets, from the Alcoa Research Laboratories, New Kensington, Penn. Tensile specimens were cut from these sheets with the longitudinal axis in the rolling direction. Both materials were recrystallized in a molten salt bath; the high-purity aluminum at 450° C for 20 min and

Jan 1, 1962

By William Laird

The predominent method of coal mining in the United States for years has been room-and-pillar mining. The reason for this has been the advantages of room-and- pillar method which is a relatively flexible system and its capital investment. The room-and-pillar method permits some selectivity in mining, especially where gas wells, faults and possible coal quality may be a factor. The mobility of continuous and conventional mining equipment used to develop entries may also be used for retreat mining of rooms and pillars. Longwall mining of coal takes place along a long straight face, or wall, blocked out between two butt or panel entries. The long faces or walls are normally projected in lengths of 61 to 183 m (200 to 600 ft) in this country. The longwall method of mining had its beginning in the United States during the 1800's. During that period, pack wall and wood posts were used for roof support. The longwall face was mined by miners using picks to undercut the coal. To keep the coal face from turning over, short wood posts called sprags were set in a slant position as the coal face was undercut to the depth of two to three feet. When the under-cutting cycle was completed, the sprags were removed to permit the coal to fall from the roof pressure. The longwall mining of coal did not take a firm hold during the 18009s, and room-and-pillar prevailed. In the early 19009s, steel jacks were introduced, and along with it, the modified caving theory. In March of 1950, a retreat longwall mining system, utilizing a plow, manually operated props, wood cribs and chock releases, was installed in one of Eastern Associated Coal Corp.'s mines.

Jan 1, 1981

By Joseph C. Buchen

In principle, productiorl of salt from sea water is a simple operation. The sun and wind cause evaporation of sea water trapped in ponds, and what is left is principally salt. Commercial production, however, requires consideration of many factors. First is a high consistent annual rate of evaporation, as well as large areas of suitable low-lying ground close to economical shipping facilities. The south end of San Francisco Bay has these requisites. Large ponds are built, by using clamshell dredges to build up levees to a height of approximately 3 ft. on ground usually lower than sea level, so that the water may be taken in through tide gates without pumping. Ponds are divided into extremely large concentrating ponds and smeller crystallizing ponds. Approximately ten times more area is required for concentrating than for crystallizing. The concentrating ponds are irregular in shape and size but the crystallizing ponds are rectangular and fairly regular in size, to aid in harvesting. The ocean water is taken into the first of a series of concentrating ponds and gradually moved forward from pond to pond as it increase:: in density, reaehing the crystallizing area as a saturated brine. This brine is pumped into the crystallizer at the beginning of the net evaporating season, usually in May, and further evaporation causes its sodium chloride content to deposit on the bottoms of the ponds. The brine must be drawn off and a fresh supply added from time to time to prevent other undesirable salts from depositing with the sodium chloride. Harvesting usually begins near the end of August and now is accomplished almost entirely by mechanical means. After harvesting, the salt is stored in large sbockpiles until required for shipping or refining. The greatest amount is used for industrial purposes and is shipped without any processing other than screening, but all salt for domestic use produced by the Leslie Salt Co. is refined by the racuum process, giving a produet consistently testing over 09.9 per cent sodium chloride.

Jan 1, 1938

By Joseph C. Buchen

In principle, productiorl of salt from sea water is a simple operation. The sun and wind cause evaporation of sea water trapped in ponds, and what is left is principally salt. Commercial production, however, requires consideration of many factors. First is a high consistent annual rate of evaporation, as well as large areas of suitable low-lying ground close to economical shipping facilities. The south end of San Francisco Bay has these requisites. Large ponds are built, by using clamshell dredges to build up levees to a height of approximately 3 ft. on ground usually lower than sea level, so that the water may be taken in through tide gates without pumping. Ponds are divided into extremely large concentrating ponds and smeller crystallizing ponds. Approximately ten times more area is required for concentrating than for crystallizing. The concentrating ponds are irregular in shape and size but the crystallizing ponds are rectangular and fairly regular in size, to aid in harvesting. The ocean water is taken into the first of a series of concentrating ponds and gradually moved forward from pond to pond as it increase:: in density, reaehing the crystallizing area as a saturated brine. This brine is pumped into the crystallizer at the beginning of the net evaporating season, usually in May, and further evaporation causes its sodium chloride content to deposit on the bottoms of the ponds. The brine must be drawn off and a fresh supply added from time to time to prevent other undesirable salts from depositing with the sodium chloride. Harvesting usually begins near the end of August and now is accomplished almost entirely by mechanical means. After harvesting, the salt is stored in large sbockpiles until required for shipping or refining. The greatest amount is used for industrial purposes and is shipped without any processing other than screening, but all salt for domestic use produced by the Leslie Salt Co. is refined by the racuum process, giving a produet consistently testing over 09.9 per cent sodium chloride.

Jan 1, 1938

By H. S. Cannon, F. N. Rhines

IT. H. Hausner( Sylvunia Electric Products Inc., Bay-side, N. Y.)—The results reported by the authors are interesting because they contribute some information on the principles of sintering and also because of a certain practical value for the manufacture of powder . metallurgical parts in production. Pressed powder compacts are frequently sintered in a boat in several layers so that the lower layers are actually sintered under the weight of the upper layers and, therefore, are frequently deformed. The authors gave information on this deformation process by determining the effect of the load on the density. The experimental setup of the authors, however, has a disadvantage—that the sintering occurred in a cylindrical container so that the deformation was stopped in the direction of the diameter. The authors should have rather called this a study of hot-pressing than of sintering. I want to call the attention of the authors and others interested in sintering under load to the experimental work described by Dawihl and Rix.' These authors sintered cylindrical compacts under a lengthwise ten-sional load of 0 to 25 g and found that the shrinkage in length and diameter changes considerably with the load, but that the volume shrinkage is affected very little by the load. H. S. Cannon (authors' reply)—We wish to thank Dr. Hausner for calling attention to the experimental work of Dawihl and Rix. The fact that they found volume shrinkage little affected by varying tensional loads during sintering seems to support the contention that the forces due to loading are equivalent to and additive to the forces which cause densification. This contention is the basis of our comparison of sintering and creep.

Jan 1, 1952

By Thomas L. Kesler

THE Cartersville mining district, 35 miles northwest of Atlanta, Ga., has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. However, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magnesian limestone. GENERAL GEOLOGY Geologic relations of the ore deposits of this district are more or less similar to those of many Appalachian districts. The lowermost Cambrian formation, heretofore called Weisner1 in this region, supposedly partly or wholly equivalent to the Erwin and Hesse quartzites as recognized to the northeast, is overlain conformably by the Shady [+] formation, also of Lower Cambrian age. In the Cartersville district, the sedimentary rocks of these formations were folded with increasing intensity eastward, and were recrystallized.

Jan 1, 1940

Discussion of the paper of Earl S. Bardwell, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. .1429 to 1441. H. O. HOFMAN, Boston, Mass. (communication to the Secretary*) :-It is pleasing to the originators of the planimetric determination of oxygen in refined copper to see that the method has been taken up by a large smelting plant to be used in every-day work after it has been simplified to suit the new conditions. Several years ago Huntington and Desch 1 had improved our mode of working. They projected the developed negative on to a screen, traced the outlines of the picture with a pencil, drew a border, and measured one constituent with. the planimeter. In order to give the work greater precision, they divided the area into squares of 1 cm. side, shaded the

Jan 11, 1913

By J. M. Locke

BRÜCKNER's revolving cylinders for roasting ores, etc., are now used at a number of the mills in Colorado and New Mexico, for the purpose of roasting and chloridizing silver ores, with highly satisfactory results, even from those cylinders of small size, erected before the many improvements of recent date. As examples of the larger improved cylinders, reference can be made to those erected at the Tennessee Reduction Works, Silver City, Grant County, New Mexico, and those which were built, in 1871, at the celebrated Caribou Silver Mill and Mines, Colorado, a mining enterprise which has proved so satisfactory as to have been lately sold to a Holland company for an enormous amount. These cylinders, as now constructed by Messrs. Lane & Bodley, of Cincinnati,, Ohio, are shown in Plate III, in which Fig. 1 is an elevation in perspective, Fig. 2 a longitudinal, and Fig. 3 a trans¬verse section. Fig. 4 is a sketch of a mill, with Brückner's cylinder. The exterior of the cylinder is a shell of boiler iron, 12 feet long by 5 feet 6 inches in diameter. The ends are partially closed with similar material, leaving in the centre a circular opening about 2 feet in diameter, bounded by a flange projecting several inches.. Upon one side is placed an opening closed by a hinged door. Upon the outside of the cylinder are bolted three bands, as shown in Fig. 1, in which the section of the first is square, and that of the third semi¬circular; the second, or middle band, is a strong spur gear. Passing through the cylinder are six pipes parallel to one another, in a plane at an angle of 15° to the axis of the cylinder; these pipes also lie in this plane at an angle of from 30° to 35° to the longitudinal, axis of the plane, as shown in Fig. 2, where the internal arrangement of the cylinder is seen, a perforated diaphragm being formed through part of the cylinder by means of perforated plates placed between

Jan 1, 1874