Search Documents

By Thomas M. Drown

The process for determining phosphorus in iron now in most general use in the laboratories of iron and steel works, is, I think, the one proposed bv Mr. Emmerton." In this process the solution of the iron for precipitation by ammonium molybdate is effected by treating the iron with nitric acid, evaporating to hard dryness in a dish, taking up with hydrochloric acid and driving off the greater portion of the hydrochloric by nitric acid. This procedure accomplishes, first, the destruction of all the carbonaceous matters; and, second; it renders all the silica insoluble. Experience has proved the former—the complete oxidation of the carbon—to be absolutely essential; but the explanation usually given, namely, that unless the carbon compounds are destroyed they will have a solvent action on the yellow precipitate, I am inclined to

Jan 1, 1890

By H. Ries

THE stabilization of a gravel road with soil is a method of treatment developed in recent years by the United States Bureau of Public Roads for the purpose of binding the constituents together better, and maintain-ing a more durable surface. The process consists in adding to the gravel or crushed stone and sand, a soil mortar, so-called, of fine sand, silt and clay, mixed in the proper proportions. The coarse gravel and sand supply structural strength and hardness; the fine sand adds embedment support to the coarse sand; the silt acts as a filler to prevent the granular particles from rocking; while the clay serves not only as a binder but also provides pores minute enough to cause connecting moisture films which are supposed to have high cohesive properties1. It will be recognized that the clay is an important ingredient both when wet and dry, and should not show excessive expansion when wet, nor correspondingly high shrinkage in drying, as otherwise there is danger of unseating the nonplastic particles. Such a stabilized road, although an improvement on one with a floating surface, will in course of time be subject to wear, and become dusty when the clay dries out and breaks up. It has been found that if some salts are added to the road mixture they tend to maintain the soil moisture and prevent dustiness of the road or raveling of the road surface. In addition to this, it is claimed that these dissolved salts cause a thinning of the moisture films on the particles, thus permitting greater compaction of the road mixture, and thereby increasing its density. This fact can be proved by noting the increased compaction which a road mixture shows when certain salts are added to the soil water. Since certain chemical substances such as sodium chloride are electro-lytes, the question arises whether they cannot have some effect on. the qualities of the clay in the soil mortar, and perhaps improve them. In view of the fact that certain salts seem to exert a favorable effect on the road mixture it is desirable that they be held in the road soil as long a time as possible.

Jan 1, 1936

By B. F. Tillson

There is a dearth of information on the economic threat of silicosis. Even the insurance companies and rating bureaus are in a quandary, and the majority of them avoid any action that will stir up an awakened public consciousness of the serious nature of this industrial hazard. Individual claims for $100,000 are now common in silicosis lawsuits. Because of ('hidden costs," in lowered plant efficiency, the total cost of this disease to industry is probably four times its apparent direct cost. The direct costs vary with the labor policies of the employer and with the labor legislation in force. Direct costs may originate in three ways: (1) voluntary assumption by the employer of medical expenses and loss of earning power of stricken employees; (2) state enforcement of industrial disease compensation acts; and (3) awards or settlements after suits in common law. Examples are offered in the last two classifications. In the Rand, South Africa, compensation laws are in effect and in approximately 20 years prior to 1932 about $65,000,000 has been awarded for silicosis and an additional liability of $34,000,000 incurred, or an average of about t5,000,000 per year. During 1932 silicosis compensation on the Rand was about $6,000,000. No figures are available for the direct capital or operating costs for preventive measures there, nor for the additional "hidden costs." It might be reasonable to assume that silicosis has cost the gold-mining industry of South Africa twenty to twenty-five millions of dollars per year. It is estimated that common-law silicosis claims have, in the last few years, aggregated $50,000,000 in New York State alone and have exceeded $300,000,000 in the United States. Attention is called to the involved nature of the insurance situation for industrial diseases in contrast to accidents. The indeterminant, insidious nature of silicosis makes it particularly difficult to predict necessary insurance premiums and reserves. The serious hazard of this disease was not properly appreciated by either insurance companies or industrialists, so sufficient study has not been given its causation, prevention, detection, treatment, and compensation. Therefore legal difficul-

Jan 1, 1934

By Roberto Fernandez

Want of knowledge on the part of experts from abroad respecting the amalgamation-system, known as the Mexican or patio process, has been the cause in this country of trouble to many foreign mining companies. This process has not been looked upon by their managers as a satisfactory method of treating silver-ores, and they prefer to employ others, which, although more modern, and often more profitable in other countries, have not proved to be so under the exceptional conditions of this country, where labor is cheap and paid in silver, while fuel is very dear. The cause of this error of judgment is probably the inexact information which has been furnished by several authors respecting the economical results of the patio process. This treatment is not suitable for silver-ores of every kind. Simple sulphides of silver are best adapted to it, and, next to these, the combinations of complex sulphides, viz., pyrargyrite, polybasite, stephanite, proustite, etc. Chlorides, bromides and iodides of silver are considered rebellious ; argentiferous galena, blende, bournonite, as also argentiferous arsenical pyrites of iron and copper, are absolutelg unsuited to this treatment. Experience has proved that high-grade ores do not give as satisfactory results as those of mediurn grades, as, for instance, carrying from 1 to 2 kilos of silver per metrical ton. The patio process, as actually practiced in this district, comprises the following operations: 1. The ore is crushed in a dry state in a roller-mill, reducing it to pea-size, from which uniform samples, and, in consequence, correct assays, can be obtained. 2. It is then thrown into the arrastra, and pulverized with water, so fine that it will pass through an 80-mesh screen.

Jan 1, 1900

By Thomas M. Drown

THE means relied on to attain uniformity in Bessemer steel may be enumerated as follows I. The appearance of the flame. II. The appearance of the slag. III. The spectrum of the flame. IV. Examination of the steel itself. At present, I wish briefly to bring forward a few considerations with reference to the last two mentioned, namely, the conditions favoring the employment of the spectroscope and examination of the steel. From the amount of careful investigation which has been devoted to the examination of the Bessemer flame by the spectroscope, both on the part of scientists and practical metallurgists, one might reasonably expect some results definite and satisfactory in their nature, first, as regards the nature of the flame, and second, as to the practical value of the spectroscope as a guide in conducting the process. We find, in fact, however, that uncertainty and confusion still exist. In Germany, where this subject has received the greatest attention, it is now very generally conceded that manganese is the cause of the well-known groups of dark bands that characterize the Bessemer spectrum. Nor is it easy to see how we can avoid accepting this conclusion, when Wedding and Von Lichtenfels have produced the manganese spectrum and found it to correspond closely with that shown by the Bessemer flame. But it is evident, on a moment's reflection, as Roscoe has recently brought forward, that manganese cannot be the only cause of the Bessemer spectrum, for we notice the characteristic bands quite as

Jan 1, 1873

By P. Somasundaran, G. E. Agar

The role of calcium, phosphate, and fluoride species in determining the zeta potential of apatite in aqueous solutions was investigated in this study. The zeta potential of apatite was determined by streaming potential measurements over a wide range of concentrations of potassium nitrate, calcium nitrate, potassium dihydrogen phosphate, and potassium fluoride solutions at various pH values. While the addition of phosphate made the apatite surface more negative at all pH values, calcium caused a significant increase of the zeta potential only when the zeta potential was negative. Fluoride addition had only a minor effect on the zeta potential, but both negative and positive values were increased.

Jan 1, 1973

By J. W. Harshbarger, E. L. Montgomery

The region of metallic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 6 km (19,700 ft). Because surface water supplies are meager, new mines require unexploited sources of water. Prolific ground water aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate ground water quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum capacities of more than 170 L/sec (2700 gpm) for individual production water wells. Results of investigations conducted by the authors demonstrate that ground water reservoirs in the Andean Highlands comprise a source of large quantities of water for the mineral industry.

Jan 1, 1986

By E. W. Dewing

ROLIN1 in 1961 published a phase diagram for the CaF2-Na3AIF6 system in which substantial (-20 wt pct) solid solubility of CaF2 in Na3A1F6 at the eutectic temperature (945°C) was indicated. The evidence was that the halt in cooling curves associated with the eutectic was lowered progressively on the Na3AlF6 side. H olm2 has recently confirmed the experimental fact, but attributes it to evaporation losses shifting the composition into the ternary NaF-CaF2-Na3A1F6 system with a consequent lowering of the eutectic temperature

Jan 1, 1970

By Robert Glass Cleland

THE CONNECTING link between Phelps Dodge and the copper mines at Bisbee and Morenci was a Canadian-born mining engineer and metallurgist named James Douglas. Judged by almost any standard, Douglas was an extraordinary man. Like John Muir of the California red- woods, he had in his blood "the heather and bog juices of Scotland," and the rugged virtues of a singularly great race. His father, for whom he was named, was a graduate of Edinburgh University, a member of the Royal College of Surgeons in London, and a man of rash and adventurous spirit. Extremely catholic in his intellectual interests and attainments, he was unusually skilled in his profession, certain-sometimes to the point of disastrous stubbornness--of his own judgments and decisions, careless of life or fortune where duty or moral issues were involved, and always deeply moved by the sufferings and misfortunes of his fellow men. The career of the senior Douglas included a curious medley of novel and adventurous experiences-prolonged hunger and cold while acting as surgeon on a Greenland

Jan 1, 1952

By R. M. Raymond

THE Mining Section of The National Safety Council recently sent out a questionnaire to operators, regarding the class of rope used, specifications required or obtained, factors of safety observed, methods of fastening ropes, lubrication, inspection, and points observed when rope is to be discarded. The answers received from this questionnaire, largely from metal mines, give interesting information, from which recommendations for safety practice on hoisting ropes are drawn. DEPTH OF MINE The depth in the majority of cases noted is from 1000 ft. to 1500 ft. (304 to 457 m.) and records come from a number hoisting from depths of 2000 to 3000 ft. Hoisting is generally done in balance, with a few companies using counterweights. Seldom, more than two shifts are occupied in hoisting. A number of large operators limit the shift for engineers to 6 hr. A few of the larger operators have separate hoists for men and supplies, with a higher class rope for men. The range of loads varies from 7 to 17 tons and greater in a few cases, with a balanced weight of 4 to 7 tons.

Jan 2, 1922

By John M. Dale

Sulfur has attractive features as a base material for coating systems. It melts at 246ºF and can be applied as a liquid above this temperature. Its melting point is just above the environmental stress level, 180°F, for most coatings and yet it is low enough to be easy to work with in comparison to many hot melt systems. The viscosity characteristics are such that sulfur lends itself to spray applications. The oxidation rate of sulfur in the atmosphere is very low and sulfur has outstanding chemical resistance characteristics, particularly in acid environments. One of the greatest potentials for these coatings appears to be in the protection of other materials. At one time, most acid tanks and pits were constructed with acid- proof brick and sulfur based mortars. This type of construction is much more expensive than sulfur based spray coatings. An attractive sulfur based coating composed of sulfur, talc, milled glass fibers and dicyclopentadiene,1 developed by the Institute for the Bureau of Mines has excellent acid assistance and can be used to protect concrete from acid attack.

Jan 10, 1973

By K. A. Johnson, F. H. Ellinger, C. C. Land

The Pu-La alloy systenz has been studied by thertnal, tnzcrographic, and X-ray diffraction methods. It is churacterized by a liquid miscibility gap, a maximum solubility of about 20 ut. pct PM in y lanthunum and 19 at. pct PI* in 0 lanthanum, very little soluibility of lanthanum in the plulonium allotropes, and the absence of intermediate phases. THE existence of immiscible liquids in the Pu-La system has been reported by Schonfeld.1 A tentative phase diagram based on the results of thermal-analysis experiments has been constructed by Poole et a1 2 This diagram shows a liquid immiscibility loop with a monotectic at 77 at. pct La and 846°C. 7 lanthanum is shown to dissolve 20 at. pct Pu and to decompose by an inverse peritectic reaction (y La = L , + p La) at about 82 at, pct La and 833°C. The ß lanthanum solvus was not determined, but the thermal work indicated a maximum solubility of 16 at. pct Pu in ß lanthanum. The present investigation has defined the solubility limits of plutonium in y lanthanum and 0 lanthanum, and, with the exception of minor discrepancies, has verified the results of Poole et al. 1) EXPERIMENTAL The electrolytic plutonium melting stocks were better than 99.9 wt pct pure, the main impurities being 90 ppm Fe and 50 ppm W. The lanthanum melting stocks, supplied by Research Chemicals and the Cerium Metals Corp., were about 99 wt pct pure, the main impurity detected by our spectrochemical analysis being 2000 ppm Fe. The components for each alloy button (-5 g) were weighed on an analytical balance and were melted together in a conventional arc furnace. If no significant weight loss occurred during melting, the as-weighed

Jan 1, 1968

By D. Coutsouradis, L. Habraken, P. Nicolaides

The TTT curves of 0.1 pct C, 13 pct Cr steels containing up to 12 pct Co have been determined in order to establish whether the effect of cobalt is similar to that observed m plain carbon steels. It is shown that cobalt increases the incubation time and decreases the transformation rate, though not in an uniform way. The bainitic transfornation is displaced to lower temperature and overlaps partially the martensitic zone. ThE effect of cobalt on the transformation of a plain carbon austenite has been studied by many investi-gators.'-3 It was shown that cobalt displaces the TTT curves to shorter times and diminishes the harden-ability. The interpretations given for this effect of cobalt are conflicting. According to E. Houdremont,4 cobalt increases the transformation rate of austenite because it increases the diffusion of carbon as shown in the experiments of E. Houdremont and H.Schrader,' R.Smoluchowski,5 and M. Blanter.6 On the other hand, M. Hawites and R. Mehl3 deny on the basis of their own experiments any effect of cobalt on the diffusion of carbon and they assume that an explanation should be found in an eventual effect of cobalt on the mechanism of nucleation and growth of pearlite. W. C. Hagel, G. M. Pound, and R. F. Mehl7 have shown by calorimetric measurements that cobalt increases the free energy of the austenite-pearlite transformation in an eutectoid steel and this result explains qualitatively the observed effect of cobalt on the rate of nucleation and growth of pearlite. The purpose of this research was to see by determination of TTT curves, if this same effect exists in 13 pct Cr steels. EXPERIMENTAL PROCEDURES The preparation of the alloys was carried out in an

Jan 1, 1960

By G. Cartaud, F. Osmond

WE have already devoted two previous memoirs to this question. In the first we collated and discussed the existing literature on the subject; in the second, we described the crystalline forms obtained by the reduction, at different temperatures, of ferrous chloride by hydrogen or by zinc-vapor. The conclusion from these researches was that the three allotropic states of iron-a, stable below A2; 19, stable between A2 and A3; and 7, stable above A3-all crystallize in the cubic system. The differences observed were such as are customarily encountered in the crystallographic records of many minerals of which allotropic varieties or isomerides are not known, but did not conform to the ordinary definition of polymorphism. It is, however, improbable that allotropic transformations, which are placed beyond doubt by a series of positive facts, do not involve some changes in the intimate structure. As a matter of fact, the crystals we did obtain were too small to allow of a precise examination, and this might introduce an element of uncertainty in the firm establishment of our conclusions. Professor H. Le Chatelier was even led to think from some of our results that iron could very well be a rhombohedron simulating a cube, and not a true cube, and it will be remembered that the crystalline form of bismuth was for a long time incorrectly regarded as cubic. Allotropy does not, however, necessarily involve such a deduction. Without departing from the cubic system at all, a whole

Nov 1, 1906

By H. F. Korman, M. C. C. Mow, P. K. Dai

INTRODUCTION Detonations of high explosives in soil and rock have been used frequently in civil engineering applications. Of particular interest in recent years has been the development of test methods to simulate the desired blast and shock environments for the testing of protective structures. The United States Air Force, in particular, the Air Force Weapons Laboratory, in conjunction with the Defense Atomic Support Agency, has in recent years, developed special technology for simulation testing of protective structures in soil and rock media. Such a technology, although initially developed for military applications, is rapidly finding its way into civil applications. One of the major problems in the design of the simulation test is the correct prediction of ground motion induced by the detonation of high explosives. This paper presents a useful prediction method which is developed specifically for ground motion in rock that is induced by the detonation of a buried planar array of explosive columns (See Figure 1). The technique of simulating shock environment using such an array is called the Direct Induced High Explosive Simulation Tech- nique (DIHEST). Normally, each shot hole may contain canisters of ammonium nitrate positioned at various depths, or a slurry explosive with detonators positioned along its length (See Figure 1). The depth and width of the array, the spacing of shot holes, the spacing of detonators, the degree of containment, and the charge weight are the variables which govern the induced ground motion

Jan 1, 1971

By William Hutton Blauvelt

Coke is the product of dry distillation of bituminous coal, by which the volatile matter is driven off, producing a hard body of cellular structure. Not all bituminous coals will coke, and there has been much discussion regarding the substance which is present in coking-coals to distinguish them from dry coals. Professor Lewes says that the bituminous matter in coal is largely derived from the spores of fossil mosses. Resins are present in all soft coals, and contribute largely to the cementing of the coke. The resinates and hydrocarbons begin to distil out at moderate temperatures and leave the pitchy residual, which at 500' C. forms a mass already well caked together, if the proportion of humus residual is not too great. This coke is soft, but if the heat be raised to 1,000° C. the pitch decomposes further, leaving carbon, and Professor Lewes is convinced that the coking bond is due to these liquid products which distil off, leaving pitch, which then carbonizes and binds the mass into coke. Professor Parr concludes that the structures of the organic compouilds of the coal Which furnish the cemeding-material for coke, and which are apparently attacked by oxygen, have not been determined and seen] to vary somesvhat in different types of coal. However, they yield, on oxidation, humic acids of varying composition which decompose into powdery residues. Because of the complex nature of these substances and the difficulty experienced in isolating and identifying them, the theory of coking is still an open problem and the explanations advanced are largely hypothetical. In the coking process the volatile matter driven off in the oven consists mainly of tar, ammonia, and gas, familiarly known as by-products. Both the quality and quantity of coke and by-products vary greatly With the composition of the coal.

Jan 1, 1913

By John R. Weeks, Dan McLachlan, John R. Lewis

DURING the operation of the iron blast furnace, aggregates of hard, infusible, yellow, cubic crystals frequently form in the interstices of the lining and on the hearth of the furnace. These were first examined by Wohler&apos; and were identified by him as a complex cyanonitride of titanium, having a formula Ti(CN)2 • 3Ti3N2, or more simply Ti10C2N8. However, recent investigators have suggested that this complex compound does not exist. Recent work by Hume-Rothery, Raynor, and Little2 on the carbide and nitride particles in titanium steels suggests that a complete series of solid solutions of the general type Ti<0+y>C0Ny exists between titanium carbide (Tic) and titanium nitride (TiN). Assuming this to be true, it seems likely that Wohler&apos;s cyanonitride of titanium is in reality a solid solution of 20 mol pct Tic in 80 mol pct TiN, .the nearly consistent carbide-to-nitride ratio probably resulting from temperature and pressure conditions in the blast furnace. The object of the present work was to investigate thoroughly this possibility of a solid solution by using the single-crystal methods of X-ray analysis. A spectrographic qualitative analysis of a sample of the yellow crystals furnished by the Geneva Steel Co. sh&apos;owed, in addition to the titanium, strong lines of vanadium and moderate to weak lines of iron, magnesium, silicon, aluminum, and calcium. The last five were probably slag impurities, but the vanadium was possibly included in the yellow crystals, owing to a great structural similarity of its carbide (VC) and its nitride (VN) to the titanium compounds, Table 11. A chemical analysis was made

Jan 1, 1952

By Cloyd M. Smith

A few years ago, the Ventilation Committee established the practice of resenting one topic each year for discussion at the annual meeting. The practice has met good response on the part of committee members and I suggest that it be continued. The topic chosen for this year, "Underground Anemometry," is a topic which has bothered me for more than 20 years. It seems to me that the coal industry is content to rely on slipshod methods for measuring the rate of flow of air underground, so I prefaced my discussional charge to committee members with the statement that I regard air measnrements made in the usual way, with hand held anemometer, as no good. Agreements and disagreements came in from more than a dozen engineers, some of whom are with operating companies, coal and metal; some with manufacturers; others with government agencies. The statement was accompanied by a questionnaire on the use of the rotating vane anemometer and by one describing two methods of using a mechanically held anemometer. The questionnaire will be considered first. The questionnaire and statement are as shown on pages 5 and 6, the committee members and respondents are given on page 4, and the general comments of the latter on page 5. Questionnaire 1. Has your company or agency issued written instructions for care and use of anemometers? If so, please enclose a copy with reply. Only one answer, McElroy&apos;s, was affirmative. It gave reference to Bureau of Mines publications1&apos;5 which recom- mend the hand held anemometer for rough measurements and indicate that am accuracy of 5 pct can be had if calibration and method factors are used. Mathews said that instructions are principally oral while Maize reported that state inspectors of his department are well trained in use and care of anemometers. 2. Are your anemometers calibrated periodically? If so, by their manufacturer? or by? Are calibralion corrections applied to all observed mean velocity readings? Only one respondent, Lee, answered negatively as to calibration. This means that anemometers are generally calibrated but the questionnaire failed to ask how often this is done. As no one volunteered the information, we have no data on this point. In six cases the instruments are sent to their manufacturers for calibration. but Krickovic reports that his company limits manu-facturers&apos; calibrations to anemometers which are used by operating personnel; those used by the engineering department being calibrated by U. S. Bureau of Standards. The Anaconda Copper Mining Co. has its ventilation engineers calibrate its anemometers. Most of the respondents say that a calibration correction is applied to each mean velocity reading, but Krickovic limits this to surveys made by the engineering department. Since Lee does not calibrate, he has no correction to apply. Maize reports that his department has its anemometers calibrated but does not apply corrections. 3. Do your men hold the anemometer by hand in measuring air flow? for 1 min? or traverse the section? for 1 min? or at? points for 5 sec each? Of 10 replies, 6 were "yes," 3 were "no," and one was "seldom" with respect to holding by hand. Among the six hand holders, four hold in a central position in the measuring section for a minute, except that two of them, Krickovic and Matthews, traverse the section by hand for survey or fan test. Their operating personnel hold by hand, centrally, for routine measurements. McElroy sometimes traverses with hand-held anemometer in rapid survey work. 4. If the anemometer is not held by hand, how is it supported? Augustadt supports the anemometer on an adjustable rod, Condon on "a rod of sufficient length to reach all points with observer standing in one position throughout traverse and at arm&apos;s length from plane of traverse." I presume that arm&apos;s length must be interpreted liberally enough to allow for arm movement, otherwise it would be impossible to manipulate the anemometer throughout the traverse section. Mancha upholds Condon in this method of traversing. Glanville hangs the anemometer on the end of a 4-ft staff by the hasp at the top of the anemometer frame. McElroy mounts it on the end of a rigid square shaft, 12 in. long, the staff being at right angles to the axis of the instrument. He traverses the section in two halves, holding the anemometer 3 feet from his body.

Jan 1, 1950

By Frederick T. Williams

The purpose of this paper is to discuss the relative merits of the large 31/8-in. machine and the small 2 1/4-in. tappet machine in driving development-headings; and although the data here presented were obtained from cross-cut headings alone, experience has shown that the results are equally true in drifting, raising and winzing. Recently we drove two parallel cross-cuts through the same formation, using a 3 1/8-in. machine at the breast of one crosscut, and a 2 1/4-in. machine of the same make at the breast of the other. The results of this work afforded an ideal comparison, since in both cases the headings were advanced through rock practically of the same hardness and breaking-properties, the amount of sludging was equal, and there was no difference in the condition of the steel or the machines, the air-pressure or the experience of the operating crews. Some operators in the Cripple Creek district contend that there is ground which cannot be handled with the small machine, the holes being too small to contain enough powder to "pull " the ground, etc. The results obtained in working the property of the Portland Gold Mining Co., however, show that the ground worked by them does not fall in this class. During a period of two years there have been driven, with the small machine, 4 miles and 308 ft. of development-headings, through a diversity of ground, including Pike&apos;s Peak granite (a coarsely porphyritic type of granite), highly indurated andesitic or pho-nolytic breccia, true massive andesite, trachytic phonolyte, tuffs, and along dikes of decomposed basalt and hard phonolyte. In every instance a satisfactory record was made. The headings here describe? mere driven through highly indurated andesitic breccia, having a hardness of from 5.2 to 7.2 and a sp. gr. of from 2.2 to 2.8. The action of the breccia under the drill was not materially different from that of ordi-

Jan 1, 1907

By L. K. Jetter, C. J. McHargue

The use of axis charts for representing the texture of cold-rolled thorium sheet was compared with conventional pole figures. Four texture components were deduced from the axis charts and shown to be consistent with the pole figures. It was shown that consideration of the pole figures alone could lead to an apparent component which is the average of two actually present. It was also shown that the spread about the "ideal" textures and the amount of material associated with each could be readily obtained Fom the axis chart method. BECAUSE of the crystallographic nature of the deformation mechanisms in metals, plastic flow results in the alignment of certain crystallographic directions with the primary flow directions. In the study of the "preferred orientation" thus developed, one wishes to discern the distribution of the crystallographic directions with respect to some reference direction, usually a direction related to the fabrication procedure, such as the rolling direction. The pole-figure method, introduced by ever,&apos; involves the plotting of the distribution of the poles of some family of planes on a stereographic projection which places the reference direction(s) at the north pole and/or in the center. By noting the angles between the reference directions and concentrations of poles on several such pole figures, one can deduce the crystallographic directions which are aligned with the reference directions. If the preferred orientation is relatively simple and well-developed, one to three pole figures may be sufficient for obtaining the desired information; if there are several texture components, more pole figures may be needed. A significant improvement in the method of representing the textures in wires and rods resulted from the introduction of the "inverse pole figure" or axis-distribution chart by Harris.2 Such a chart gives directly the distribution of the reference axis relative to the standard stereographic projection. There has been widespread acceptance of this method for the representation of fiber textures, and methods have been proposed for converting observed diffraction intensities into axis densities.2-6 The suggestion by Mitchell and Rowland3 and Jetter, McHargue, and williams5 that sheet textures could be represented as distributions of rolling, normal, and transverse directions have been criticized on the basis that they offer no significant advantage over a combination of two ordinary pole figures and that it has not been proved that sheet textures can be treated as quasi fiber textures.6 If the purpose of a texture determination is to study some property which is related to the orientation of a particular crystallographic plane or direction, then conventional pole figures certainly are sufficient. For example, the distribution of the slip planes in face-centered cubic metals (the (111) pole figure) serves to indicate the variation in mechanical properties of sheet. On the other hand if the study is directed at an understanding of the factors influencing texture formation, it is desirable to know not only the preferred orientation but the kind and degree of spread from it and the relative amounts of material in each component, if there are more than one. Axis charts give this information as well as the orientation distributions. Consider the procedure for deducing a texture component from a pole figure for the (111) planes

Jan 1, 1961