Search Documents

By Helmut Thielsch

DURING the last three decades a great many arguments have been presented on the subject of "mosaic" or "block" structures of metals. Apparently because of insufficient evidence, the "block-structure" theories have never been widely understood among the physical metallurgists in this country, and most investigators among the few that have tried to demonstrate the existence of such an inner structure of crystals or grains have failed to recognize also the existence of a lamellar structure. Moreover, little thought has been given to justify the existence of such "lamellar" or "mosaic-block" structures on a theoretical basis. Since properties such as plasticity, ferromagnetism, hardness, diffusion, and others may be explained by structural faults in the lattice network of the crystals, the great importance of a more detailed knowledge of the structure within crystals or grains becomes now evident. Because of the vast extent of the field of submicroscopic structures, it shall be the purpose of this paper only to review the more important of the results obtained by other investigators, especially in Germany, where a great deal of attention has been given to mosaic structure during the last three years. The origin of this mosaic pattern f and effects of cold reduction and recrystallization will be shown in further studies later on. IMPERFECTIONS IN CRYSTALS The many terms used in the literature to denote structural types of crystals are often not clearly defined. To clear up some of the confusion, the meaning of the more important terms will be given here. Ideal, or Perfect Crystals.-Crystals without any structural imperfections are called "ideal crystals," or "perfect crystals," meaning a homogeneous interior structure of atoms, ions or molecules, as the case may be. In other words, at every point in the interior of the crystal exactly the same orientation of the crystallographic axes of the coordinate system would exist. The surface of such a body, if etched with an appropriate etching reagent, would reflect light with perfect uniformity. Crystals of this type are almost nonexistent. Real Crystals.-" Real crystals"' may contain various types of structural defects, which can be classified into: (I) lineage structure, (2) mosaic-block structure, (3) lamellar structure. The inhomogeneities existing in these groups mean that the orientation of the crystallographic axes will not be the same at every point within the interior of a crystal (or grain of a polycrystalline body). Perfect Real Crystals.-The term "perfect real crystals" is generally used to describe crystals with minute structural or thermodynamical inhomogeneities. The former

Jan 1, 1945

By Helmut Thielsch

During the last three decades a great many arguments have been presented on the subject of "mosaicJ' or "blockJJ structures of metals. Apparently because of insufficient evidence, the "block-structure" theories have never been widely understood among the physical metallurgists in this country, and most investigators among the few that have tried to demonstrate the existence of such an inner strutture Of crystals or grains have failed to recognize also the existence of a lamellar structure. Moreover, little thought has been given to justify the existence of such "lamellar" or "mosaic-block" structures on a theoretical basis. Since properties such as Plasticity; ferro-magnetism, hardness, diffusion, and others may be explained by structural faults in the lattice network of the crystals: the great importance of a more detailed knowledge of the structure within crystals or grains becomes now evident. Because Of the vast extent of the field Of submicroscopic structures, it shall be the purpose Of this paper only to review the more important of the results obtained by other investigators, especially in Germany, where a great deal of attention has been given to mosaic structure during the last three years. The origin of this mosaic patternt and effects of cold reduction and recrystallization will be shown in further studies later on. Imperfections in Crystals The many terms used in the literature to denote structural types of crystals are often not clearly defined. To clear up some of the confusion, the meaning of the more important terms will be given here. ideal, or perfect without any structural imperfections are called "ideal crystals,,or ''Perfect'' crystals,n meaning a Homogeneous interior structure of atoms, ions or molecules, as the case may be. In other words, at every point in the interior of the crystal exactly the same orientation of the crystallographic axes of the coordinate system would exist. The Surface of such a body, if etched with an appropriate etching reagent, would reflect light with perfect uniformity. Crystals of this type are almost nonexistent. Real Crystals.—L'Real crystals"' may contain various types of structural defects, which can be classified into: (I) lineage structure, (2) mosaic-block structure, (3) lamellar structure. The inhomogeneities many,in these groups mean that the orientation of the crystallographic aies will not be the same at every point within the interior of a crystal (or grain of a poly crystalline body). 'Perjecl Real Crystals.—The term "perfect real crystals " is generally used to describe crystals with minute structural or thermo-dynamical inhomogeneities. The former

Jan 1, 1946

By Helmut Thielsch

During the last three decades a great many arguments have been presented on the subject of "mosaicJ' or "blockJJ structures of metals. Apparently because of insufficient evidence, the "block-structure" theories have never been widely understood among the physical metallurgists in this country, and most investigators among the few that have tried to demonstrate the existence of such an inner strutture Of crystals or grains have failed to recognize also the existence of a lamellar structure. Moreover, little thought has been given to justify the existence of such "lamellar" or "mosaic-block" structures on a theoretical basis. Since properties such as Plasticity; ferro-magnetism, hardness, diffusion, and others may be explained by structural faults in the lattice network of the crystals: the great importance of a more detailed knowledge of the structure within crystals or grains becomes now evident. Because Of the vast extent of the field Of submicroscopic structures, it shall be the purpose Of this paper only to review the more important of the results obtained by other investigators, especially in Germany, where a great deal of attention has been given to mosaic structure during the last three years. The origin of this mosaic patternt and effects of cold reduction and recrystallization will be shown in further studies later on. Imperfections in Crystals The many terms used in the literature to denote structural types of crystals are often not clearly defined. To clear up some of the confusion, the meaning of the more important terms will be given here. ideal, or perfect without any structural imperfections are called "ideal crystals,,or ''Perfect'' crystals,n meaning a Homogeneous interior structure of atoms, ions or molecules, as the case may be. In other words, at every point in the interior of the crystal exactly the same orientation of the crystallographic axes of the coordinate system would exist. The Surface of such a body, if etched with an appropriate etching reagent, would reflect light with perfect uniformity. Crystals of this type are almost nonexistent. Real Crystals.—L'Real crystals"' may contain various types of structural defects, which can be classified into: (I) lineage structure, (2) mosaic-block structure, (3) lamellar structure. The inhomogeneities many,in these groups mean that the orientation of the crystallographic aies will not be the same at every point within the interior of a crystal (or grain of a poly crystalline body). 'Perjecl Real Crystals.—The term "perfect real crystals " is generally used to describe crystals with minute structural or thermo-dynamical inhomogeneities. The former

Jan 1, 1946

By R. K. Iyengar, G. C. Duderstadt

An investigation was carried out to determine the effect of Ca-Si additions on the dissolved oxygen content of liquid steel. An apparent equilibrium was reached after holding the melt for some time when the total oxygen content of the melt was identical with the dissolved oxygen. Results of the investigation show that for deoxidation with silicon and manganese the apparent equilibrium is reached after 8 to 12 min and the oxygen content of the melt is in good agreement with values reported in the literature for similar steel compositions. Ca-Si additions decrease the dissolved oxygen content appreciably below that obtained with Si-Mn deoxidation. It is postulated that some calcium dissolved in liquid steel at the time of its vaporization combines with dissolved oxygen to form CaO which then fluxes the manganese silicate, thereby lowering the activity of the deoxidation products. Slow flotation of calcium silicate inclusions is attributed to their slower growth rate. An addition of aluminum (to yield <0.005 pct Alsol) prior to introduction of Ca-Si improves the kinetics of removal of resulting deoxidation products. WITH the introduction of continuous casting of billets and blooms, application of calcium-containing alloys for deoxidation purposes has gained new interest. More so than in conventional ingot casting, the degree of control of the dissolved and total oxygen contents in steel for continuous casting can determine the success or failure of the operation because these affect both surface (pinholes) and internal quality of the billets. Of the available deoxidizers, only silicon has so far found wide application. However, in the typical range of application (0.20/0.30 pct Si), it is too weak a deoxidizer to suppress pinhole frequency to the level desirable for all but the least demanding appli-cations (approximately 10/50 pinholes per sq ft, de-pending on degree of subsequent reduction). On the other hand, Vincent&apos; has shown that it requires ap-proximately 0.007/0.008 pct A1 soluble in the steel to suppress pinhole formation to <10 pinholes per sq ft. In view of the difficulty of consistently maintaining this aluminum level and the associated problem of tundish nozzle constriction2 when aluminum is added to the ladle, steelmakers have searched for other de-oxidation alloys to circumvent the problem. Calcium-containing alloys offer such a possibility. When employed as a partial substitute for silicon, CaSi (30 pct Ca/60 pct Si) additions are reported to yield adequate pinhole contro1.3 Its use simultaneously preserves the "fluidity" of the steel and ensures good castability.4 Oxygen contents as low as 0.007 to 0.014 pct have been obtained with CaSi additions varying between 3 to 8 lb per ton.5-7 Due to the high degree of vaporization of calcium at the temperature of molten steel and the different methods used to introduce it into the liquid, the reported results show considerable scatter and lack of consistency. According to several investiga- deoxidation tors, the flotation characteristics of CaSi products are not as favorable as those found for alumi-num but are similar to those established for silicates with low alumina content.678 Thus, cleanliness ratings were improved when CaSi was replaced by a com-bination of Si + A1 followed by CaMnSi additions.5,9 In view of the lack of a comprehensive description of the deoxidation potential of CaSi alloys, a study was undertaken of the effect of CaSi additions on oxygen content in comparison to Si + Mn and Si + Mn + Al. The alloy chosen for this study contained 63 pct Si, 32 pct Ca, <3 pct Al, and 2.5 pct Fe. EXPERIMENTAL PROCEDURE The experiments were divided in three groups as shown in Table I. In each group, the CaSi addition was increased successively while maintaining the melt composition constant. The experiments in the third group were designed to determine the effect of prede-oxidation with small amounts of aluminum. Ingot iron, containing 0.02 to 0.03 pct C and 0.03 to 0.05 pct Mn, was melted in a 100-lb magnesia crucible. Pig iron was added to the melt under air in an induction furnace to attain the desired carbon content of 0.05 to 0.15 pct and thereby control the initial oxygen content of the melt between 0.04 and 0.015 pct. After removal of the slag, the furnace was sealed and argon was introduced through an opening in the graphite cover, Fig. 1. When the desired temperature was reached, electrolytic manganese was added to the melt and pin samples were taken (7 mm silica tubing) to establish initial oxygen content. To obtain maximum efficiency, CaSi and metallic silicon were introduced in a sealed steel pipe into the bath. This procedure assured minimum loss of calcium through vaporization as the deoxidants were always released at the bottom of the melt. Samples were taken at regular intervals and quenched in water. Temperature of the bath was measured with a Pt/Pt-10 pct Rh thermocouple. Portions of the pin sample were used for oxygen analysis; five determinations per sample were made to obtain average oxygen content. Oxygen analyses were made by the inert carrier gas fusion method with frequent cross checks with the vacuum fusion method.

Jan 1, 1970

University of Nevada&apos;s recent Bonanza Days celebration turned out to be the real thing when Kennecott Copper Co, presented the school with $30,000 for new laboratory equipment for the MacKay School of Mines, J. C. Kinnear, Jr., general manager of Kennecott&apos;s Nevada Div., handed the check to Stout, university president, Chemical Construction Inter-American Ltd,, signed a contract with Noranda Mines, Ltd. for construction of a sulphur-iron plant in the Niagara Peninsula. Work has been started and it is expected that the plant will be finished by summer 1954.

Jan 6, 1953

By W. W. Anderson, D. G. Girton

The photoluminescence of Pr, Nd, Ho, Er, Tm, and Yb in CdS, and Ho, Er, Tm, and Yb in ZnSe has been observed from crystals Prepared by diffusion using rare earth metals and an excess chalcogen pressure. For a given temperature, time, and chalcogen pressure the spectral characteristics were very reproducible from run to run, and the emission intensity for Nd, Er, and Yb in CdS was as high or higher than the best vapor phase doped crystals we have grown. For a few rare earths it was found that certain conditions of diffusion tend to yield optimum rare earth emission intensity with respect to the background lattice emission. Photoluminescence measwements of Yb in CdS as a function of depth gave a profile which was neither a Gaussian nor complementary error function. Part of the profile appears to arise from a fast component of the diffusion and the other part from a slow diffusing component. At 960°C and 33 atm S pressure, a com -plimentary error function approximation of the slow diffusing component gave a diffusion coefficient of D = 1.3 x 10-9 sq cm per sec. MOST of the studies of emission from rare earth ions in II-VI compounds have been reported on crystals doped during growth,1,2 although Kingsley and Aven prepared ZnSe:Er by diffusion for paramagnetic resonance and fluorescence studies. Pappalardo and Dietz prepared CdS:Yb by diffusion, but they made optical absorption measurements., We know of no study on the properties of rare earth diffusion in the II-VI compounds. To date we have diffused Pr, Nd, Ho, Er, Tm, and Yb into CdS, and Ho, Er, Tm, and Yb into ZnSe and observed the rare earth emission spectra. For a given temperature and chalcogen pressure, the emission characteristics are very reproducible from run to run and for Yb, Nd, and Er in CdS, as good as the best crystals we had prepared by doping during vapor phase growth.2 The emission of Pr, Ho, and Tm has been observed in CdS prepared by diffusion for the first time. Previous attempts2 to prepare these later three materials by vapor phase growth were unsuccessful. The problem of obtaining reproducible characteristics in II-VI semiconductor compound work is well known.5 Not only is it difficult to reproduce results from one laboratory to another but it is sometimes difficult to reproduce results from one growth run to another under ostensibly identical conditions within one laboratory. This situation has been particularly bothersome in research on the luminescence of rare earth activated ZnS1 and Cds2. Crystals from one vapor phase growth run would show very strong rare earth line emission while crystals from a nearly identical run would show no rare earth emission. It was also observed on occasion that the intensity of the rare earth emission was not constant over the entire volume of a single crystal. MATERIAL PREPARATION AND INSTRUMENTATION Vapor phase grown boules of CdS were supplied by Dow Corning. This material was characterized by a free electron concentration of n - 3.5 x 1015 cm-3 and Hall mobility of 350 sq cm per v sec at room temperature. There were microscopic voids and decorated precipitates in some samples. The precipitates annealed out at diffusion temperatures but the voids remained. Single crystal rectangular samples of mm dimensions were sawed from the boules. The ZnSe was polycrystalline, UHP grade from Eagle-Picher. Poly-crystalline samples were sawed from the ingots. The samples were lapped, polished on one side, etched in a solution of 0.5 M K2Cr2O7 in 16 N H2SO4, and thoroughly washed in distilled water. A sample, excess sulfur (or selenium), and 5 mg of rare earth metal (turnings) were sealed in a 3.6 cm3 quartz ampoule at about 2 X 10-5 torr. The high chalcogen pressure used (1 to 30 atm) prevented thermal etching of the crystals and affected the diffusivity and solubility of the rare earth ions in the crystal lattice. For meaningful or reproducible results, it is thus necessary to specify the vapor pressure at which the diffusion was carried out. It is assumed that a negligible amount of the chalcogen was used in the formation of rare earth sulfides or selenides Our sulfur vapor pressure calculations are based on data assuming S2, S6, and S, molecules only in which case the equilibrium constants are given by6 where the pressures are expressed in torr. Selenium vapor consists of a mixture of Se2, Se4, Se6, and Se6 molecules. The selenium vapor pressure was calculated using equilibrium constants given by The status of the rare earth source during diffusion is unknown, i.e., the partial pressures of the rare earth metal and of the rare earth chalcogenides has not been determined. All emission spectra were recorded at 77°K on a Perkin-Elmer model 98-G spectrometer using a 640 line per mm grating. No correction was made for the spectrometer and detector spectral sensitivity. Excitation was by means of an XBO 1600 w xenon arc

Jan 1, 1970

NEW YORK SECTION J. E. Johnson, Jr., Chairman Edgar Rickard, Vice Chairman. D. M. Liddell, Secretary, 7 Wall St., New York, N.Y. C. A. Bohn, Treasurer John V. N. Dorr Lewis W. Francis. The annual meeting of the New York Section was held on Wednesday, June 6, with about 40 members in attendance. The treasurer re a brief summary of-the financial statement for the year, and the secretary&apos;s report was read. These reports were ordered placed on file together with the report of the auditors for the two previous years.

Jan 8, 1917

By Paul L. Russell

THIS is a progress report of an experiment being undertaken in cooperation with the Bethlehem Steel Corp., the Crucible Steel Co., and the Rock Bit Sales and Service Co., involving heat treatment of the shank ends of drill steel. This experiment is being conducted by the U. S. Bureau of Mines in its experimental mine, Mining Research Branch, Bluemont, Va. The purpose of the experiment is to determine the effect of an increase in the time the steel soaks in the furnace during the hardening heat. It has been thought that increasing this time produces a soft zone below the lugs resulting in a metallurgical notch that causes early failure. Each of the steel companies furnished enough 11/4 - in. straight carbon, hollow, round steel to make up 10 sets of drill steel, in each instance the steel bars were from the same heat. These sets of drill steel, consisting of 2-ft, 4-ft, 6-ft, and 8-ft lengths were fabricated by the Rock Bit Sales and Service Co. Special attention was given to the forging of the steel to produce the best rods possible. The heat treatment of all thread ends was identical and followed the best practice. The heat treatment of the shank ends of five sets of steel from each company produced a soft zone 2 to 4 in. in front of the lugs. It was decided that possibly the best way to obtain this effect was not to overlap the hardening heat but to let the steel soak for an additional 30 min before quenching. Therefore the only variable in the test steels is the length of time the shank ends were in the furnace. The remaining drill steel shanks were treated as follows: Heat treatment in pyrometer-controlled furnace at 1550°F. Quenching oil at 105°F to 125°F temperature. Areas for heat treatment were; shanks, 11 in.; threads, 9 in. Time at heat, standard practice, 20 min for 11/4-in. steel. Actual drilling tests were made in greenstone, (a metamorphosed basaltic rock), and in epidosite. Greenstone has a specific gravity of 2.96 and a compressive strength of 44,200 psi. Epidosite has a specific gravity of 3.26 and a compressive strength of 63,100 psi. All drilling tests were made using a 31/2-in. column-mounted, automatic feed drifter, with a controlled air pressure of 90 psi at the throttle. Tungsten-carbide bits of 2 in. diameter were used for all drilling. Contrary to expectations the drill steels that were allowed to soak for the additional 30 min before quenching performed better than the steels that were heat treated according to standard practice. This performance, as shown in Table I, was especially noticeable in the drilling of epidosite. The "longheat" drill steels furnished by Company "A" drilled 154 pct more minutes than the "standard-heat" steel. Expressed in feet, the "long-heat" steel drilled 114.60 ft more before failure than the "standard-heat" steel. The "long-heat" steel furnished by Company "B" drilled 37 pet more minutes or 60.39 ft more before failure than the "standard-heat" drill steel. The effect of the long heat treatment was not as evident when the steels were drilling in greenstone (Table II). In greenstone, the increase in minutes drilled by the "long-heat" steel over the "standard-heat" steel was 47 pet and 1 pet, respectively, for Companies "A" and "B."

Jan 1, 1952

By S. Weissmann, P. R. Swann, D. F. Wriedt

The sizes and density of precipitates in an intemally oxidized 0.19 wt pct Al-Ag single crystal have been determined by low-angle X-ray scattering and by transmission electron microscopy . The correlation in particle sizes measured by the two techniques is reasonably good. For an oxidizing temperature of 800°C the particles were found to INTERNAL oxidation of dilute alloys of aluminum in silver produces an oxide which has an excess of oxygen compared to Al2O3.&apos; It is believed that the excess oxygen is an indication of the small sizes of the oxide particles. Depending upon the particular model chosen for the oxide structure, the size of the o-A1 particles can be calculated as a function of the oxygen-to-aluminum ratio. These calculations pre- have diameters in the range 30 to 140A, with a mean size of about 50.4 as observed by electron microscopy. At lower oxidizing temperatures, less than 600°C, no clearly resolved particles are formed, and it is suspected that if A1-0 clusters exist they must be exceedingly small, i.e., 10A or less in diameter. dicto that the particles would vary in size from 15 to 100A. This range of sizes is amenable to detection by both small-angle X-ray scattering and transmission electron microscopy. This paper compares the cluster sizes in such internally oxidized A1-Ag alloys determined by transmission electron microscopy and small-angle X-ray scattering. SPECIMEN PREPARATION Single crystals were prepared from 99.9999 pct Ag, obtained from Cominco Products, and 99.99 pct Al, obtained from Aluminum Co. of America. All melting operations were carried out in graphite molds under flowing purified hydrogen in a horizontal zone refiner. The silver was first degassed,

Jan 1, 1964

THE annual meeting of the Institute was held at the Office of the Secretary on Tuesday, May 23d. President Holley appointed Messrs. J. C. Kent and Frank Firmstone scrutineers to examine the ballots of the Institute. The following were declared elected: President-ABRAM S. HEWITT. Vice-Presidents-W. P. BLAKE, E. B. (AXE, R. W. RAYMOND. Managers-R. W. HUNT, J. S. NEWBERRY, T. F. WITHERBEE. Treasurer-T. D. RAND. Secretary-T. M. DROWN. The meeting was then adjourned to June 20th. The adjourned meeting to be held in Philadelphia.

Jan 1, 1877

By Royal B. Jackman, Carle R. Hayward

Two comprehensive papers have appeared regarding the forms of copper that occur in smelter slags, one by Frank E. Lathe1 and the other by C. G. Maier and G. D. Van Arsdale.2 These authors comment on other published results and draw conclusions from their own investigations. The development of X-ray examination of minerals and improvement in high-power microscopic methods make it possible today to get additional evidence by means that were not available to earlier investigators. The present work was confined to reverberatory slags obtained from five different plants. Some definite conclusions were reached regarding the forms of copper present in these slags. In most cases these agree with some of the findings of Maier and Van Arsdale but new methods of attack were used in the investigation. Conclusions of Previous Investigators Various important conclusions reached by previous investigators are summarized in the following paragraphs, arranged chronologically. William A. Heywood:3 Slag losses increase with grade of matte but with the same grade of matte losses decrease as the acidity of the slag increases. Lewis T. Wright:&apos; Slag losses are only partly due to prills of matte. It is suggested that part of the copper is dissolved in the slag. J. Parke Channing9 A considerable part of the copper enters the slag as silicate or oxide and not as sulfide. C. A. Grabill:6 Slag losses are both physical and chemical. Physical losses, due to poor settling, gas flotation and slight differences in specific gravity, are small under normal conditions. Chemical losses may- be due to formation of oxides or to solution of metals and sulfides. The last is considered the most important. John W. James:&apos; The copper in converter slag is largely the oxide and as such enters the reverberatory slag when converter slag is added to the charge.

Jan 1, 1934

By R. E. Lindstrom, D. G. Peterson, H. J. Heinen

Alkaline alcohol solutions were investigated by the Federal Bureau of Mines for improving the desorption rate of gold and silver from metal-laden activated carbon generated in gold processing circuits. Factors affecting the desorption, such as temperature, alcohol content, type of alcohol, and alkalinity, were studied. Nearly complete metal desorption was obtained in 5 to 6 hr at 80º C using a solution containing about 20 vol-pct alcohol and 1 pct sodium hydroxide. Sodium sulfide was shown to be effective for selectively precipitating silver from the carbon strip solutions, thereby providing a means for producing high- purity gold by subsequent electrolysis.

Jan 1, 1976

By H. B. Huntington

Some of the basic problems in understanding elec-tromigration in metals are discussed, along with the attempts that are being made to handle them. One such problem is the effect of the electrostatic forces. It is now acknowledged that the momentum exchange with charge carriers plays generally a dominant role in the driving force but the question remains to what extent the electrostatic force may still be effective. The electromigration of interstitial impurities is also an area which presents some intriguing questions. For the substitutional impurity, moving by the vacancy mechanism under the influence of an electric field, the correlation considerations are somewhat more complex than have been previously recognized. Another problem of basic importance in the calculution from first principles is the strength of the "electron friction" force, say for a simple one-band metal. A related problem growing out of the preceding is the prediction of the direction of the "electron wind" force for metals with band structure involving both holes and electrons. THE term electromigration has come to be used to describe the flow of matter in condensed phases carrying high electronic currents such as metals and alloys, whereas one usually reserves the term electrolysis for situations where the current is largely ionic, particularly in the liquid state such as molten salts. It follows that the mass transport number in electromigration is always very small, of the order of 10-7. Studies of electromigration date back some 30 years but the modern period would appear to date from the work of Seith and Wever1 who in the mid 1950&apos;s first incorporated markers to display mass motion relative to the lattice and first suggested that the direction of the mass flow was primarily determined by the sign of the charge carriers. Since that time interest in the field has grown steadily and more rapidly recently as certain technological applications became apparent. Chief of these is certainly the deleterious effects that electromigration can cause, even at relatively low temperature, to current-carrying elements in integrated circuitry.2 These phenomena have been the subject of intense study and considerable ingenuity. On the constructive side electromigration has proved a useful tool in the purification of certain metals.3 The interest of this paper is, however, centered more on the basic aspects of the subject than on its technological applications. That high electric currents should give rise to mass flow in metals and that the driving force should be more directly associated with momentum exchange with the charge carriers than with the electrostatic field are ideas that no longer cause surprise or particular interest. The field has matured to the point where the general concepts are widely accepted and continued progress in basic understanding rests on more detailed and quantitative exploration. It is the purpose of this paper to point out what are some of the current problems. As a result, we expect to raise more questions than we answer. The first of these will be the role of electrostatic forces, if any, in electromigration. A second section will deal with the electromigration of interstitials. A third and final section treats with electromigration of substitutional impurities or of the matrix atoms themselves. ELECTROSTATIC DRIVING FORCE In the conceptual treatments of electromigration it has been customary to write the driving force in terms of an effective charge number Z* and to divide it into two terms F = e£Z* = e£[Zel- z(pd/Nd)(N/p)(m*\m*\)] [1] The first of these represents the electrostatic force under immediate consideration in this section and the second and usually dominating term for metals arises from momentum exchange with charge carriers, commonly called the "electron drag" term. As can be seen it is set proportional to the electrons per atom, z, and the ratio of the specific resistivity of the moving entity to the corresponding resistivity per matrix atom. The (m*/Im*I) factor takes into account the fact that the sign of the charge carrier determines the sign of the driving force. The specific resistivity of the moving entity is averaged over its path. In the case of motion of the matrix atoms by vacancies this gives rise to approximately one-half the resistivity at the saddle point since the scattering power of the atom at its equilibrium position bordering the vacancy differs only slightly from that of a normal matrix atom. Although the formulation of the "electron drag" term in Eq. [I] is based on a highly simplified model for electron defect scattering, the essential features implicit in the expression are common to all the theoretical approaches that have so far appeared in the literature.4-6 As for Zel, most treatments of electromigration have included the quantity as the parameter which measures the direct interaction of the electrostatic field with the ion and equated it to the nominal valence of the latter. However, there has been considerable discussion whether this interaction may not be 0 in many cases.6 If the moving ion is always enveloped by the same distribution of shielding charge, then clearly its motion will not involve any work done by the electric field and one can expect there will be no electrostatic force exerted on such a neutral composite. From this point of view the shielding charge around the ion would be said to be complete and hence the entity within the Debye shielding sphere would be unaffected by the electrostatic field per se. There is, however, the prospect that, as the moving ion progresses, new charge comes in to participate in the shielding action

Jan 1, 1970

By B. R. Eichbaum, J. E. Murphy, J. A. Eisele

The US Bureau of Mines demonstrated ferric chloride leaching of galena concentrate on a continuous bench scale basis. Leaching was performed at 95°C (200°F) and with a contact time of 15 minutes. The ferric chloride leaching solution was continuously fed to a leaching tank at a constant rate for periods up to 45 hours. In each test, a constant redox potential was maintained in the slurry exiting the leaching tank by controlling the concentrate feed rate. In the 45 hour test, lead extraction exceeded 99.5%, and the lead chloride produced was 99.97% pure.

Jan 1, 1986

California Academy of Sciences, Golden Gate Park, San Francisco, Calif C E Grunsky, President A price list of the publications of the Academy will be sent upon request The voluminous literature issued by the Academy deals principally with subjects in the fields of botany, zoology and biology. The Proceedings are issued as volumes, but separates of each paper contained in the proceedings may be obtained at prices indicated in the list of publications A few of the papers which may be of interest to geologists, follow, and indicate the scope and character of the papers of the Society

Jan 1, 1933

MEMBERS of the Research Committee lunched to-gether on Monday and discussed the work and plans of the Committee. Some re-assignment of duties was made and a request put in for another member specializing in lead and zinc. By request, Director Flinn of the Engineering Foundation presented the problem of the proposed investigation of iron alloys. It was decided to call together a special committee in May to determine on recommendations. A. C. Fieldner discussed coal research and Chairman Manning was authorized to ascertain by letter ballot the opinions, on certain phases of this, of all members of the Committee.

Jan 3, 1928

By Charles F. Park

Mining in the Pacific Coastal Region has passed through three stages of development. First came the gold rush days, a period when gold and silver were the objects of intensive search. Second was the development of the high-grade base-metal deposits and of the smaller and more refractory precious metal deposits. And third was the modern period that covers the discovery and development of the rarer metals, of large low-grade deposits, and of the industrial and nonmetallic minerals. Brief discussions of the salient geologic features of the region and of a few of the better known mineral deposits are given. The regional geology is favorable for continued exploration and discovery of new deposits and districts.

Jan 1, 1968

K. Baumgarten has returned from active service in France. He reports that he saw C. W. Campbell, formerly with the 2d Engineers on the Chateau Thierry front, and believes that the latter returned to the United States on August 1. He also saw J. J. Croston; G. J. Sielaff, recently transferred to the Gas Service; Thomas M. Smither, survivor of the Tuscania after a 10-mile swim to Ireland. While in Paris he en-deavored to see Prof. Sauveur, but was unsuccessful. F. K. Borrow was given a commission as Lieutenant in the Royal Garrison Artillery in 1914, but had to relinquish it, on account of ill health, in August, 1915. His health has much improved and he hopes to resume active work toward the end of this year. Davis, A. W:, see British Columbia Engineers, below. Alfred Fox, Jr., enlisted in the Public Schools Brigade, Royal Fusiliers, in September, 1914; was gazetted Lieutenant in the Royal Field Artillery in December, 1914, promoted to Captain in November, 1915, and Adjutant to 78th Brigade, Royal Field Artillery, in January, 1916. He was appointed Staff Captain of the 12th Divisional Artillery in November, 1917. He has served continuously in France since July 1, 1915. He was awarded the Military Cross in January, 1917, and four times mentioned in despatches. E. Fraser-Campbell writes that he joined the London University 0. T. C. in January, 1918, for five weeks; enlisted with the Argyll and Sutherland Highlanders in February, 1918, and attended a training course for officer cadets at Chatham for six weeks. He was commissioned 2d Lieutenant, Royal Engineers, in April, 1918. After two months on home training at Chatham, he landed in France on June 23, 1918, posted to 180th Tunnelling Co., R. E., and is now with his unit up on the line.

Jan 10, 1918

By J. L. Rodda, M. L. Fuller

In connection with an investigation in this laboratory on the high-zinc side of the copper-zinc system, it was observed that well developed segregate structures of the Widmansttten type were formed when a secondary phase precipitated from the solid solution of copper in zinc. This paper presents an analysis of the crystallographic relationship between the segregate and the solid solution matrix. The data to be presented are an interesting addition to the literature on segregate structures in that the plane of segregation is one of the less densely populated planes. In agreement with the generalization of C. H. Mathewson and D. W. Smith&apos; the plane of segregation in the matrix contains the direction of closest atomic packing of the lattice. Furthermore, the matrix and the segregate are both hexagonal close-packed, which has not been reported hitherto in the 1iternture.l The increasing commercial importance of zinc alloys containing copper makes this fundamental study of value to the metallography of zinc alloys. Zinoeich Copper-zinc Alloys Copper enters into solid solution with zinc to at least 1.8 per cent at 400" C., according to W. M. Peirce.3 The solubility is less at lower temperatures. Thus a solid solution of copper in zinc, saturated at an elevated temperature, will precipitate the excess copper in a separate phase at a lower temperature, conditions of concentration, time, and temperature being suitable. The nature of these two phases has been established by the X-ray method of crystal analysis. Westgren and Phmgmén4 and also Owen and Preston5 have shown that the solid solution eta (7) is of the substitu-tional type with copper atoms replacing zinc atoms on the hexagonal

Jan 1, 1933

By Robin O. Williams

The increase in internal energy as the result of deformation has been measured for lead, aluminum, silver, nickel, iron, and zirconium by using rapid, adiabatic compression. The stored energy increase is roughly Proportional to the strain; the propor-tionality constant increases rapidly with increasing melting point. The fraction of the mechanical energy which is stored increases more slowly, since the strength of the metals also increases with melting point. The values of the stored energy are considered accurate to about 10 pet. The present values appear about 50 pet larger than the more reliable published results where comparisons are possible. It is possible that this difference is due to the high strain rate used in this investigation. Immediately after deformation all these metals release energy at a rate roughly proportional to (time)-&apos;. This release is considered to be associated with dislocation motion but in aluminum (and copper) some additional process seems to be present. This release can represent 20 pet or more of the stored energy. WHEN pure metals are plastically deformed, most of the mechanical energy is converted into heat. The energy remaining within the metal is significant in that it is the energy of the disorder produced and thus detailed knowledge of this energy is a powerful tool in understanding the nature of deformational disorder. While much effort has been expended on this problem, the amount of information available is limited. The situation as of 1958 has been carefully reviewed by Titchener and ever.&apos; The present results have been obtained by a new experimental approach to this problem. The method necessitates high-strain rates which make comparisons with published results less certain, but a high-strain rate is an advantage in that the energy release immediately after deformation can be followed. EXPERIMENTAL PROCEDURE In the experimental method used, the internal (stored) energy is given as the difference between the mechanical work used in deforming the sample and the heat which is released (the first law of thermodynamics). The work is supplied by two identical hammers swinging freely from a fixed height, the available energy being the product of the mass, the gravitational constant, and the distance through which the center of gravity moves. The initial temperature rise of the sample represents the heat produced by the deformation. The sample temperature is determined by a small thermocouple embedded in and supporting the sample. This process can be repeated over and over to produce increased strains. Most samples are run through about five cycles to a total strain of around 0.7. Further details are covered elsewhere. The determination of the heat is dependent upon the sample weight, its specific heat, the rise in temperature, and any gains or losses to the surroundings. One is dependent on published results for specific heals (the values were taken from a collection).3 The values must be accurate to about 0.1 pet in order that they not affect the results. The best values thus do not contribute to the uncertainty, but this is probably not always the case. The accuracy of the temperature rise is limited primarily by knowledge of the thermocouple characteristics over short temperature intervals, but careful calibration eliminates this as an important factor. One can calculate readily the heat flow between the sample and hammers if the time of contact and the sample temperature are known and if there were no oil at the interface. Assuming the maximum temperature difference, upper values for this interchange have been calculated (the time of contact is determined from the decrease in sample length) and it may or may not be significant. However, no correction is colnsidered necessary because of the presence of a thin oil film which has a thermal conductivity much less than the metals. Except for the possible uncertainty in specific heat, the heat is considered to be adequately known. The mechitnical losses which are recognized as important are: 1) friction between the sample and the hammer:;, 2) the kinetic energy in the hammer suspension system which may not be entirely usable, 3) the rebound energy of the hammers, and 4) the vibration of the hammer heads. All these have been covered in detail elsewhere2 and only the more significant points are made here. The friction turns out to be small except for soft materials (lead)

Jan 1, 1962