Search Documents

By E. A. Gulbransen, J. W. Hickman

The physical and chemical structure of the oxide films formed on metals and alloys is of interest in our understanding of their protective properties. According to Pilling and Bedworth,¹ if the specific volume of the oxide is equal to or greater than that of the metal, a compact or continuous structure results; if the volume of the oxide is less, a cellular or porous structure forms. With the cellular type of coating the surface layer of oxide offers no impedance to oxidation; at a given temperature the rate of oxidation is quite constant. On the other hand, the compact type of coating acts as an effective barrier to oxygen and the rate of oxidation will follow a parabolic law. The recent work of Gulbransen2 and of Leontis and Rhines3 on the oxidation of magnesium indicates that it is not necessary for the volume of the oxide to be greater than that of the metal in order that the oxidation may follow a parabolic rate law. One exception to the rule of Pilling and Bedworth¹ is noted by Scheil;4 namely, tungsten. At 500° and 700°C long-time oxidations indicate a linear rate law with time. However, Dunn's6 0xidation measurements from 700°to 1000°C indicate that a parabolic rate law is followed. The oxide is mainly yellow WO a with a thin layer of the blue oxide. Preliminary results on the oxidation of tungsten6 in the temperature range 400° to 500°C indicate that the oxidation does proceed according to a parabolic rate law. Irrespective of the actual rate law that tungsten may obey, it is of interest to compare the results obtained on the oxidation of tungsten in the thin film region with those found when the metal is scaling. A time-temperature study of the oxides formed on both molybdenum and tungsten may indicate whether there exist any peculiarities in the oxide structures of the thin film region compared with those of the scaling region of oxidation. In a recent paper the authors7 presented an investigation of the structures of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper. The results of these studies are presented in graphical form as existence diagrams of the oxides on a time-temperature scale. The existence diagrams of the oxides occurring on some of the metals are simple and show few chemical transitions, but there are many cases in which the physical state of the oxide surface changes as a function of time and temperature, as evidenced by the appearance or disappearance of orientation effects and sharpness of patterns. In general an increase in temperature results in an increase in

Jan 1, 1947

By E. A. Gulbransen, J. W. Hickman

THE physical and chemical structure of the oxide films formed on metals and alloys is of interest in our understanding of their protective properties. According to Pilling and Bedworth,1 if the specific volume of the oxide is equal to or greater than that of the metal, a compact or continuous structure results; if the volume of the oxide is less, a cellular or porous structure forms. With the cellular type of coating the surface layer of oxide offers no impedance to oxidation; at a given temperature the rate of oxidation is quite constant. On the other hand, the compact type of coating acts as an effective barrier to oxygen and the rate of oxidation will follow a parabolic law. The recent work of Gulbransen2 and of Leontis and Rhines3 on the oxidation of magnesium indicates that it is not necessary for the volume of the oxide to be greater than that of the metal in order that the oxidation may follow a parabolic rate law. One exception to the rule of Pilling and Bedworth' is noted by Scheil;4 namely, tungsten. At 500° and 700°C long-time oxidations indicate a linear rate law with time. However, Dunn's5 oxidation measurements from 700° to 1000°C indicate that a parabolic rate law is followed. The oxide is mainly yellow W03 with a thin layer of the blue oxide. Preliminary results on the oxidation of tungsten6 in the temperature range 400° to 500°C indicate that the oxidation does proceed according to a parabolic rate law. Irrespective of the actual rate law that tungsten may obey, it is of interest to compare the results obtained on the oxidation of tungsten in the thin film region with those found when the metal is scaling. A time-temperature study of the oxides formed on both molybdenum and tungsten may indicate whether there exist any peculiarities in the oxide structures of the thin film region compared with those of the scaling region of oxidation. In a recent paper the authors' presented an investigation of the structures of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper. The results of these studies are presented in graphical form as existence diagrams of the oxides on a time-temperature scale. The existence diagrams of the oxides occurring on some of the metals are simple and show few chemical transitions, but there are many cases in which the physical state of the oxide surface changes as a function of time and temperature, as evidenced by the appearance or disappearance of orientation effects and sharpness of patterns. In general an increase in temperature results in an increase in

Jan 1, 1947

[ALBERTA, UNIV. OF AZIZ, Khalid FLOCK, Gerald L HART, Richard T NAOER, Walter SCHEIDEGGER, Adrian E SHIELS, David Alexander ALUMINUM CO. OF AMER. GAYLE, Douglas Z MINTER, John L MOORE, Thomas C NEUSTAEDTER, J A REISS, Royal W SPEYRER, Henry R AMARILLO OIL CO. BEST, John B Jr COX, Arthur F GRAY, Stanley F Jr KEENS, Roy J MORRIS, Edward S TIPTON, J A WHITIS, Thurman S]

Jan 1, 1961

By N. W. Lord

The process of molten-zone refining is analyzed for long ingots and many zone passages. Formulas are derived which give the resultant impurity distribution in terms of finite series. A comparison with the approximate procedure of Hamming is given. HE physical principles and applications of an extremely physicalprinciple efficient form of metallurgical refinement has been described by Pfann. The purpose of the present paper is to describe a method of analyzing exactly the particular program used which enables the segregation effect to be predicted for any number of molten-zone passages in a long ingot. The method is applied to the particular case of refinement of an ingot whose impurity initially is uniformly distributed throughout its length. A number of molten zones of equal length are passed through the ingot effecting a radical redistribution of impurity. Pfann has indicated an approximate method, due to R. W. Hamming, of calculating the resultant concentration after each successive zone pass for a particular value of the segregation constant defined in his paper. Here a solution will be presented in terms of the number of zone passes and the segregation constant. The expression, though cumbersome, is exact and susceptible to ordinary numerical computation procedures. The results of a similar computation using the procedure of Hamming are presented in a table together with the exact results of the present method. The discrepancy in terms of absolute concentrations is tabulated for the first eight zone-lengths. To establish the notation (which follows that of Pfann1 as closely as possible) and physical basis of the analytical equations, the physical model and principal assumptions may be reviewed. An alloy of two elements, where there is formed a continuous range of solid solutions, usually does not melt as a simple compound. Rather, a temperature is reached where the solid solution is in heterogeneous phase equilibrium with a liquid solution of different composition. The temperature dependence of these equilibrium compositions forms part of the phase diagram. For very small concentrations of a solute B in a solvent A, this usually takes the form of Fig. 1. Sometimes the solidus and liquidus slope upward. This corresponds to a segregation constant (defined below) which is greater than unity. The segregation constant is now defined as k = Cn(x)/CnI(x) [1] where C,,(x) is the impurity concentration in the solid ingot at distance x during the nth passing of a molten zone and Cnl (x) is the impurity concentration of the liquid zone from which the solid at dis- tance x is formed (see Fig. 4 of ref. 1.) C (x) remains the same after passage of the zone. The constant k may be either greater or less than unity in general. Purification in the former case is effected only in a finite ingot and in the portion that is melted last. For k less than unity purification is effected even in an infinite ingot. The method which follows gives, in the former case, the successive increases in impurity concentration and, in the latter case, the successive decreases in concentration. The general case of impurity redistribution will be considered first, and purification will be discussed later on. The analysis rests on the following assumption: The movement of the zone is too rapid to allow appreciable atomic rearrangement in the solid sections and too slow to disturb the uniform impurity distribution in the liquid zone characteristic of equilibrium. Hence, the composition in the solid at the left solidifying interface will be determined by Eq. 1 while the impurity concentration of the liquid zone will be uniform throughout its length. The reasoning which follows closely parallels that of Appendix 11 in Pfann&apos;s paper. It is reviewed here for the case of the nth zone pass in order to make clear the meaning of an operator essential to the present method. Fig. 4 of ref. 1 shows the movement of a molten zone of length 1 in an ingot of total length d. Each Cn(x) can be determined from the condition that the amount of solute added to the zone during an incremental advance, dx, is due to the melting in of a solid portion C(x)dx and the freezing out of kCnl(x), that is d I —r- CnL (x) dx = Cn-1 (x+l)- kCnL (x) dx or, in terms of Cn(x) d k k —— C,(x) +—c.(x) =— Cn-1 (x + l). [2] dx l l This, of course, is derived from the main assumption, the fact that 1 is constant, and that the total impurity content previously present up to x + 1 is constant . A correction has to be made for the region (d — nl) < x < d. This is due to the zone length changing during the passage of the solidifying interface beyond x = d — 1. Since the general solution would be too complicated otherwise, only the region 0 < x < d — nl is considered. The general solution of Eq. 2 is

Jan 1, 1954

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ANDREWS, CLARENCE W., 2d Lieutenant, 12th Batt. Infantry Replacement Regiment. ANDREWS, JOSEPH C., Ordnance Dept., U. S. A. ARLUCK, A. A., Headquarters, 1st Corps of Artillery, A. P. O.. No. 759, A. E. F.

Jan 9, 1918

By P. M. Aziz, I. Markson, C. S. Barrett

The abnormal after-effect in twisted wires that occurs when untwisting is interrupted by etching con be brought under control and used to study the mechanical properties of thin surface films and how they are effected by reagents and heat treatment. Results are given of studies of oxide films on high purity aluminum. IF a wire is subjected to plastic deformation by torsion and then released, it untwists in the normal after-effect, but under certain circumstances the untwisting is abruptly lessened or reversed by the application of an etchant to the wire.1,2 This abnormal after-effect may occur, for example, if there is a coherent oxide film on the surface of the wire which is removed by the etchant. Following a suggestion of A. H. Cottrell that predicted this effect, it is attributed to dislocations that had piled up beneath the oxide layer and represents the rapid release of residual stresses caused by these dislocations. When the layer is removed, the stress relief may be by escape of piled-up dislocations from the metal, or by an activation of latent sources of dislocations located at the surface, together with rebalancing of elastic stresses to compensate for the loss of stressed material, as in a residual stress analysis determination, these mechanisms acting singly or in combination.&apos; The slower the attack of the reagent, the more gradual is the stress relief and the smaller the change in strain rate when the reagent is applied. A study has been made of the factors that influence the magnitude of the normal and abnormal after-effects with the object of developing techniques suitable for a quantitative investigation of the influence of various surface films on dislocations in wires, and of the rate and extent of the attack on the films by different reagents. It was found that reasonable sensitivity and reproducibility could be achieved if a suitable choice of variables was made and if these variables were held constant through a series of experiments. The method was then applied to a study of oxide films produced and treated in different ways on the surface of high purity aluminum wires, and to a study of the damage to these films caused by various reagents. Experimental Procedure The material used throughout this work was prepared from 99.9968 pct Al. This high purity aluminum was melted, cast into 1/2 in. diameter ingots, and then swaged and drawn without intermediate annealing to 0.040 in. diameter wire. A sketch of the apparatus employed for twisting is shown in Fig. 1. The test wires were mounted into the apparatus by cementing one end of the wire to the beaker and the other to the tube with laboratory wax of high melting point. The length of the wire between the waxed joints was 4.2 & 0.2 cm. Extreme care was taken during mounting to avoid cold-working the wire. The wire was twisted through 335" in 2 to 4 sec by rotating the pinion on the gear box until the vertical post on the rotating table, which was initially touching the horizontal stop, was arrested by the stop. All the tests were conducted with apparatus and reagents at the same temperature (about 25°C). In all tests, except those where the duration of the initial torque was investigated, the torque was applied for a period of 2 min. At the end of this time the table was rotated back a few degrees away from contact with the stop and the wire allowed to untwist. The after-effects were measured by reflecting a beam of light from the mirror shown on the apparatus. After the wire had untwisted for 6 min, a reagent was carefully poured into the beaker and thereby applied to the surface of the wire.. In some tests the liquid in the beaker was removed after a few minutes and replaced by an-

Jan 1, 1954

By C. E. Birchenall, G. Derge

IN studying the kinetics of slag-metal reactions, it has become increasingly apparent that a complete knowledge of all aspects of interface phenomena will be required to clarify these processes adequately. A part of the data required for all oxidizing slags used in the refining of impure iron to steel is the rate of exchange of iron between the slag and metal phases. The simplest equilibrium of this type is that between liquid iron and iron silicate slag when both phases are equilibrated with the silica crucible containing them. In this study, the exchange of iron between the two liquid phases has been measured by using radioactive Fe as tracer. The observed high exchange rate indicates the ease with which such interfaces may be crossed in refining processes. The experiments required for this study involved relatively minor and normal modifications of well established techniques. Melting was accomplished by induction heating in heavy walled, fused silica, rotating crucibles." Rotation was used to minimize dilution of the slag by crucible erosion. The melting stock was ingot iron. Slags were prefused in iron crucibles using chemically pure grade oxide reagents. The special conditions applying to the active iron additions will be described for individual experiments. Suitable precautions were observed with regard to protection against radiation hazards.&apos; Identification of Activity This particular study was initiated several years ago, but held in abeyance because the radioactive iron available at that time contained a foreign activity which concentrated in the slag so as to mask the iron activity and render the results unin-terpretable. With the benefit of experiences from other studies, radioiron of suitable purity can now be prepared. As received from the Isotope Div. of A.E.C., the unit appears to contain Fe + Fe50 and a high activity cobalt. The cobalt and iron are separated by repeated ether extractions, and the purified iron stored for sufficient time for the Fe&apos;7 44 day half-life) to decay to negligible activity, leaving only Fe as the active isotope. This was confirmed by the absorption curves for slag and metal samples from heat No. 1. In Fig. 1 the experimentally measured points for the absorption curves of slag and metal are fitted by the calculated slope of 5.8 mg per sq cm in aluminum, which corresponds to the Mn K doublet emission resulting from the capture of an orbital electron of Fe" by the nucleus. This shows that the radioactive species are the same in both slag and metal and identifies it as Fe55 Description of Individual Heats For the first heat, the radioactive iron was contained in the prefused slag. The active Fe55 had been precipitated with carrier and was added as Fe2O3 during fusion in the iron crucible. The charge of 500 grams of ingot iron was melted, the protective iron sleeve added, rotation started, and a prefused, inactive slag was added to allow the system to approach equilibrium. After about 5 min at temperature, the wash slag was skimmed and the active slag added. Initial slag and metal samples were taken as soon as the slag was molten. Additional samples were taken at indicated intervals thereafter. Slag samples were dipped with a small iron spoon and metal samples were sucked into 1/4 in. ID silica tubes. The slag and metal samples were pulverized and mounted for radioactive counting. The slag samples were analyzed chemically for FeO. Temperature was read after the last slag sample by immersion of a Pt-Pt-Rh thermocouple protected by a fused silica sheath. Since no significant variation of rate with temperature was observed

Jan 1, 1954

STANDING COMMITTEES. Executive. CHARLES F. RAND, Chairman. JAMES F. KEMP, JOSEPH W. RICHARDS, ALBERT R. LEDOUX, BENJAMIN B. THAYER. Membership. BENJAMIN B. THAYER, Chairman. WALTER R. INGALLS, JOHN H. JANEWAY, JR., JOHN D. IRVING, HERMAN A. PROSSER. Finance. EDWARD L. YOUNG, Chairman. KARL EILERS, JAMES GAYLEY. Library. JAMES F. KEMP, Chairman. JOHN HAYS HAMMOND,3 E. GYBBON SPILSBURY,2 ALEX. C. HUMPHREYS,4 BRADLEY STOUGHTON.

Jan 9, 1913

MINING METHODS W. J. COULTER, Chairman P. B. BUCKY, Vice-Chairman CLYDE E. WEED, Vice-Chairman ROBERT S. PALMER, Secretary Alluvial Mining CLINTON BERNARD O. B. PERRY NORMAN CLEAVELAND C. M. ROMANOWITZ R. B. EARLING J. B. STAPLER BENERE H. GRANTCHARLES THURMAN Open-Cut Mining Iron. A. D. CHISHOLM EARL E. RUNNER G. E. DIEHL G. E. LEVEQUE P. G. HARRISON SIMPSON RICHEY W. A. STERLING

Jan 1, 1943

STANDING COMMITTEES. Executive. CHARLES F. RAND, Chairman. JAMES F. KEMP, JOSEPH W. RICHARDS, ALBERT R. LEDOUX, BENJAMIN B. THAYER. . Membership. BENJAMIN B. THAYER, Chairman. KARL EILERS, JOHN H. JANEWAY, JR., JOHN D. IRVING, HERMAN A. PROSSER. Finance. EDWARD L. YOUNG, Chairman. KARL EILERS, JAMES GAYLEY. Library. JAMES F. KEMP, Chairman1 JOHN HAYS HAMMOND,3 E. GYBBON SPILSBURY,2 ALEX. C. HUMPHREYS.4 BRADLEY STOUGHTON.

Jan 10, 1913

STANDING COMMITTEES. Executive. CHARLES F. RAND, Chairman., JAMES F. KEMP, JOSEPH W. RICHARDS, ALBERT R. LEDOUX, BENJAMIN B. THAYER. Membership. BENJAMIN B. THAYER, Chairman. WALTER R. INGALLS, JOHN H. JANEWAY, JR., JOHN D. IRVING, HERMAN A. PROSSER. Finance. EDWARD L. YOUNG, Chairman KARL EILERS, JAMES GAYLEY. Library. JAMES F. KEMP, Chairman.1 JOHN HAYS HAMMOND 3 E. GYBBON SPILSBURY,2 ALEX. C. HUMPHREYS 4 BRADLEY STOUGHTON.

Jan 6, 1913

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B POTTER 1888 RICHARD PEARCE 1889 ADAM S HEWITT 1890

Jan 1, 1923

STANDING COMMITTEES. Executive. CHARLES F. BAND, Chairman. JAMES F. KEMP, JOSEPH W. RICHARDS, ALBERT R. LEDOUX, BENJAMIN B. THAYER. Membership. BENJAMIN B. THAYER, Chairman. WALTER R. INGALLS, JOHN H. JANEWAY, JR., JOHN D. IRVING, HERMAN A. PROSSER. Finance. EDWARD L. YOUNG, Chairman. KARL FILERS, JAMES GAYLEY. Library. JAM ES, F. KEMP, Chairman. JOHN HAYS HAMMOND,3 E. GYBBON SPILSBURY,2 ALEX. C. HUMPHREYS,4 BRADLEY STOUGHTON.

Jan 8, 1913

STANDING COMMITTEES. Executive. CHARLES F. RAND, Chairman. JAMES F. KEMP, JOSEPH W. RICHARDS, ALBERT R. LEDOUX, BENJAMIN B. THAYER. Membership.. BENJAMIN B. THAYER, Chairman. WALTER R. INGALLS, JOHN H. JANEWAY, JR., JOHN D. IRVING, HERMAN A. PROSSER. Finance. EDWARD L. YOUNG,Chairman. KARL EILERS, JAMES GAYLEY. Library. JAMES F. KEMP, Chairman. JOHN HAYS HAMMOND,3 E. GIBBON SPILSBURY,2 ALEX. C. HUMPHREYS,4 BRADLEY STOUGHTON.

Jan 7, 1913

STANDING COMMITTEES Executive CHARLES F. RAND, Chairman. JAMES F. KEMP, JOSEPH W. RICHARDS, ALBERT R. LEDOUX, BENJAMIN B. THAYER. Membership BENJAMIN B. THAYER, Chairman. KARL EILERS, JOHN H. JANEWAY, Jr., JOHN D. IRVING, HERMAN A. PROSSER. Finance EDWARD L. YOUNG, Chairman. KARL EILERS, JAMES GAYLEY. Library JAMES F. KEMP, Chairman.1 JOHN HAYS HAMMOND,3 E. GYBBON SPILSBURY,2 ALEX. C. HUMPHREYS,4 BRADLEY STOUGHTON.

Jan 1, 1914

STANDING COMMITTEES. Executive. CHARLES F. RAND, Chairman. JAMES F. KEMP, JOSEPH W. RICHARDS, ALBERT R. LEDOUX, BENJAMIN B. THAYER. Membership. BENJAMIN B. THAYER, Chairman. KARL EILERS, JOHN H. JANEWAY, JR., JOHN D. IRVING, HERMAN A. PROSSER. Finance. EDWARD L. YOUNG, Chairman. KARL .EILERS, JAMES GAYLEY. Library. JAMES F. KEMP, Chairman 1 JOHN HAYS HAMMOND,3 E. GYBBON SPILSBURY,2 ALEX. C. HUMPHREYS, 4 BRADLEY STOUGHTON.

Jan 12, 1913

By C. H. Hitchcock

Report C6 of the Second Geological Survey of Pennsylvania, by Charles E. Hall, describes the rocks of the Philadelphia belt, and sets forth conclusions widely different from those derived by others from the study of similar strata along the same stratigraphical line. Mr. Hall classifies these rocks into three groups: First, the Philadelphia schists and gneisses, well shown within the city limits and

Jan 1, 1884

By W. Rostoker, R. P. Elliott, B. W. Levincer

Phase equilibria in the Ti-Cr-Mo system have been investigated for alloys containing 100 to 40 pct Ti in the temperature range 550° to 1300°C. Five experimental isothermal sections and a surface of incipient melting are presented in addition to a summary projection of the space. Seven vertical sections have been constructed from the isothermal sections. A STUDY of the system Ti-Cr-Mo was undertaken as part of a program sponsored by Watertown Arsenal toward the development of titanium-base phase equilibrium diagrams of potential technical importance to alloy development. The scope of the investigation included the composition range contained by the titanium corner and the line of 64 pct Ti (all compositions are by weight) and the temperature range 550" to 1100°C. A surface of incipient melting was constructed from measurements on a large number of alloys. The system Ti-Cr has been established.&apos;-? The phase diagram is characterized by a wide miscibility field of the solid solution at elevated temperatures and a eutectoid reaction of the type: (15 pct Cr) + TiCr, (685C). The a solid solution has a very limited capacity for solution of chromium (< 0.5 pct Cr). The intermediate phase TiCr2 has at best a very narrow composition range. It has been shown that two allotropic modifications of this phase exist. However, this behavior does not appear to be perceptibly reflected in the form of phase boundaries of the type + TiCr,. In the system Ti-Mo,9-10 the phase is stabilized to successively lower temperatures with increasing molybdenum content. There are no known intermediate phases. The a solid solution is limited to less than 0.5 pct Mo. Because of the very extensive range of the phase, the ternary system was ideally suited to the determination of the phase boundaries by the parametric method of Andersen and Jette." A parametric surface was constructed to provide the necessary basis for the application of this method. Preparation and Treatment of Alloys More than 60 alloy compositions were prepared for the study of this system. Alloy buttons of 10 grams were arc-melted in a nonconsumable electrode furnace using inert atmosphere protection and a water-cooled copper crucible. The construction and operation of this type of melting unit have been adequately described elsewhere.&apos;&apos; To insure complete solution of alloy additions, the buttons were remelted alternately on top or bottom as many as five times. This was accomplished by a suitable mechanism for "flipping" over the ingots. Iodide titanium (99.97 pct Ti) was used as the alloy base. An especially high quality chromium (99.9 pct Cr) was obtained from the National Research Corp. Molybdenum sheet (0.005 in.) of 99.9 pct purity was used.

Jan 1, 1954

Executive. CHARLES F. BAND, Chairman. JAMES F. KEMP, JOSEPH W. RICHARDS, ALBERT R. LEDOUX, BENJAMIN B. THAYER. Membership. BENJAMIN B. THAYER, Chairman. WALTER R. INGALLS, JOHN H. JANEWAY, JR., JOHN D. IRVING, HERMAN A. PROSSER. Finance. EDWARD L. YOUNG, Chairman. KARL EILERS, JAMES GAYLEY. Library. JAMES F. KEMP, Chairman 1 JOHN HAYS HAMMOND,3; E. GYBBON SPILSBURY,2 ALEX. C. HUMPHREYS,4 BRADLEY STOUGHTON.

Jan 5, 1913

Mining Methods JAY A. CARPENTER, Chairman CLYDE E. WEED, Vice-Chairman ROY A. HARDY, Secretary Alluvial Mining CLINTON BERNARD O. B. PERRY NORMAN CLEAVELAND C. M. ROMANOWITZ R. B. EARLING J. B. STAPLER BENERE H. GRANT CHARLES THURMAN Open-Cut Mining Iron G. E. DIEHL EARL E. HUNNER P. G. HARRISON G. E. LEVEQUE Copper LOUIS BUCHMAN W. H. GOODRICH J. H. DAVIS WALTER S. LARSH

Jan 1, 1941