Search Documents

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By G. W. Tracy

The material balance equation has been used for many years by engineers to determine reservoir performance. The use of this equation in general has been twofold: first, to determine the oil-in-place in a reservoir; and second, to predict the future performance. The Schilthuis form of the material balance equation, or one equivalent to it, has been used by many of the engineers. The use of the Schilthuis form in predicting future performance has proved to be laborious in that one generally must make several estimates at each step of the trial and error calculation before arriving at a check of the oil-in-place. A method is presented for expediting the calculations. The Schilthuis form of the material balance has been rearranged into a more useable form. In using the material balance to predict the future performance of a reservoir, it has become common practice to estimate the incremental oil production for each step of the calculation which corresponds to a given pressure reduction. Instead of estimating the incremental oil production, the method outlined in this paper better lends itself to estimating the instantaneous gas-oil ratio. A check of oil-in-place is more easily accomplished by estimating gas-oil ratio since it is less sensitive to small inaccuracies. This method incorporates the same self-checking feature inherent in the Schilthius form. DEVELOPMENT OF SIMPLIFlED EQUATION In the development of the simplified equation, the Schilthuis form of the material balance equation will he used. Substituting in Equation 1 for and rearranging terms In Equation 2, the cumulative oil production (n) is multiplied by a factor which is uniquely a function of pressure. Also, the cumulative gas production (G) and net water influx are also multiplied by factors which are a function of pressure alone. These factors are called and are defined as follows: Using these factors, Equation 2 becomes The equation in this form is easier to manipulate mathematically than any of the previous forms which, have been used. Sources of data for the pressure factors are a bottom-hole fluid analysis and the ratio of initial gas cap volume to oil volume in the reservoir. AID IN DETERMlNING THE ORIGINAL OIL-IN-PLACE Each of the curves and +, have a similar shape. Each is infinite at the bubble point pressure. As lhe pressure is reduced below the bubble point, the

Jan 1, 1956

By L. H. Robinson

Triaxial compression tests on Indiana limestone indicate that chemical additives in the pore fluids can increase or decrease the strength in plastic failure but not in brittle failure. Tests using a series of the sodium salts of dicarboxylic acids show that odd-number carbon-atom chains decrease the yield strength as much as 3.0 x 10 3 psi, and even-number carbon-atom chains increase the yield strength as much as 9.0 x 102 psi. ,The most effective chemical (sodium citrate) decreased the yield strength of Indiana limestone from 16.0 x 103 to 12.0 x 103 psi. The chemical additives investigated have no influence on microbit drilling rate when drilling with zero differential pressure. However, when drilling at a 2.0 x 103-psi pressure differeniial and using an odd-number carbon chain compound as the circulating fluid, the roller bit drilling rates were slower than with water whereas the drag bit drilling rates were faster. One even-number carbon chain compound added to the circulating fluid produces the opposite effect: the roller bit drilling rate is slightly faster than with water and the drag bit slower than with water. INTRODUCTION A Russian book by Rehbinderl published in 1944 generated much interest in the possibility of aiding and accelerating the destruction of solids by the action of a liquid in which the solids are deformed. This book describes a process in which microcracks are generated during elastic deformation. To describe this process, the rock is divided into three zones: (1) the zone in which the destruction takes place, (2) the predestruc-tion zone (an affected area immediately below the destroyed zone) and (3) the undisturbed specimen. Consider a load applied normally to a surface of an infinite slab of rock. Immediately below the point of application of the load, the rock is destroyed by compression or shear forces. Below this area of destruction, because of a great number of discontinuities ranging from defects to weak points in crystals of discontinuities in crystal latices, very small cracks are created in or between the crystals (often referred to as microcracks). Upon removing the load, the broken rock in the destroyed zone could be removed. In the lower predestruction zone, however, the microcracks in and between the crystals could disappear by the process of rehealing, i.e., the molecular attraction from one side of the crack to the other side being sufficient to completely eliminate the crack. Thus, a large number of these microcracks possibly exist only for a relatively short period of time. The concept of small cracks being generated within the crystals of a rock is not unreasonable. If the rock matrix is deformed below the yield point, some of the defects present within the crystalline structure could start small cracks through the interior of the grains. Upon removal of the load, these microcracks reheal (or the newly generated surfaces come back together) so that all evidence of cracks completely disappears. Under various types of loading, and in various types of fluids, the rehealing of these cracks would be time dependent. If a liquid adhered to the surface of a rock, it could penetrate into the microcracks and thus delay or prevent the rehealing process. This suggests that the prevention of healing of the microcracks may be dependent upon the wetting characteristics of the solid. Thus, rocks which are water-wet should be more easily destroyed in water than in nonpolar hydrocarbon liquid. Adsorption of a liquid could also reduce the free surface energy which could explain the decrease in strengths of materials under nonrepetitive-type loading. Rehbinder's work prompted Boozer, Hiller and Serdengecti 2 to examine the effects of pore fluids on the deformation of rocks subjected to triaxial compression over a range of confining pressures, temperatures and strain rates. Fluids which strongly adsorbed on the rock grain surfaces decreased the strength of sandstone and limestone, which deformed plastically. For certain strain

By George W. Riter

OUR mineral-land laws need revising so as to provide definite title at the outset to the mineral deposits within any definite piece of land. The laws as they now stand, especially those applicable to lodes, breed uncertainty as to rights of possession prior to patent; and to my mind this is the worst feature of all, worse even than the apex bugbear. It is now almost impossible for anybody to tell-with certainty what mineral rights exist within any area that is not covered by patent, or whether any valid rights exist at all. Our system is unique in permitting individuals to appropriate and exploit mineral lands of the public domain without notice of any kind to the Federal government, and to relinquish them without any ceremony at all. The result is a clouded record that cannot be cleared up until each claimant is put to some sort of final proof. In order to accomplish this, new Federal legislation will be required. The requirements for a mineral survey and the proceedings for patent have always been cumbersome and expensive; and perhaps out of regard for the poor claim owner, who can ill afford the outlay for that sort of thing, the law does not require him to go. through it unless he chooses to do so. Consequently, every active mining district has become encumbered with tangled groups of doubtful or conflicting locations, whose rights and boundaries, when any valuable ore is found, must usually be determined by lawsuits that are as expensive and as distressing as the stakes are high. So deeply has litigation entered into our mining system that a claim whose rights have never been disputed would probably be set down offhand, by $miner of the old school, as of no value. Think of the litigation over rights of possession on the Com-stock lode—12 leading companies involved 'in an aggregate of 245 suits within a period of less than eight years! Ambiguous local records; the chance of erroneously placed or obliterated monuments; doubt as to the sufficient performance of the statutory annual labor; uncertainty as to prior conflicting or overlapping locations; anxiety as to the changing attitude of the Department of the Interior and the Forest Service—such considerations as these make an unpatented mining claim an unclean thing in the eyes of possible investors. Is it any wonder that they keep themselvesand their money at a safe distance,

Jan 1, 1915

By A. A. Smith

THE application of indium to bearings was first advocated by C. F. Smart1 in 1938, for the purpose of inhibiting corrosion of certain bearing alloys. He found that a thin layer of indium plated on the bearing surface and subsequently diffused at elevated temperatures markedly decreased the rate of corrosion in lubricating oils containing organic acids. Most of his work was done on cadmium-base alloys, although he showed that the treatment was also effective for copper-lead and other alloys. Since their introduction, indium-treated bearings have found considerable use, particularly in connection with airplane motors.2 Undoubtedly the effectiveness of the indium plate in resisting corrosion depends upon its relative concentration on the bearing surface after the diffusion treatment and after prolonged use at operating temperatures. Some diffusion experiments were made on a number of base metals that had been indium plated, to determine the depth of penetration after heating for reasonably long periods of time. As only the practical aspects were desired, no attempt was made to determine actual diffusion constants. METHOD Two different series of experiments were carried out to study the diffusion of indium into several base metals. Cast cylinders about one-inch diameter were machined to 0.750-in. diameter, so as to remove all surface imperfections, and final finishing was done with oo sandpaper. The original diameters were very carefully measured with micrometers and then a layer of indium was electrolytically deposited on the cylinders from a sulphate bath.3 In the first series of experiments, about 0.002 in. of indium was deposited and diffusion was carried out at 150°C. for a period of 500 hr. in a thermostatically con- trolled electric oven. After the diffusion period, successive layers were machined from the specimens and analyzed spectro- graphically and chemically-the spectro- graphic examination serving as a guide to determine which layers should be chemically analyzed. Apparently there was some surface oxidation of the indium plate due to the long heat-treatment, which may have had some effect on the diffusion. Also, the cadmium alloy showed some incipient melting, which probably was caused by the formation of a low-melting eutectic. To eliminate these factors, another series of experiments was carried out by heating in an electrically heated, automatically controlled, oil bath at lower temperature. The preparation of the specimens was the same as before except that a layer of indium 0.0001 in. thick, an amount commonly used commercially on bearings, was deposited on each of the cylinders. Diffusion was carried out at l20°C. for a period of 200 hours.

Jan 1, 1944

By A. E. Wells

IN 1866, Thomas Graham1 called attention to the volume of gases, three times the volume of the sample, evolved from a meteoric iron heated in an evacuated porcelain tube. From that time to this the occurrence and significance of gases in metals have been the subject of investigation by many workers, among whom Sieverts,2 Iwasé3 and 0. W. Ellis4 stand preeminent. Sieverts and Iwasé concerned themselves with the solubility of a number of gases in metals in the liquid and solid states. They determined the absorption coefficients of these gases, and in all cases found a sharp change in solubility at the melting point of the metals. Ellis analyzed the gases evolved by solidifying copper and those occluded by the solidified metal. Lobley and Jepson5 endeavored to determine the effects of hydrogen, carbon monoxide and nitrogen on the porosity of copper that was allowed to solidify in the presence of each gas after 30 min. exposure to it in the

Jan 1, 1930

James W. Malcolmson died suddenly on Dec. 26, 1917, at Kansas City, Mo., where he had made his home for the past ten years. He was born at Dover, Kent, England, on Oct. 6, 1866. He graduated from the Royal School of Science, London, England, in 1889, and almost immediately after graduation came to Mexico, accepting a position with the Michoacan Railway and Mining Co., as mining and mechanical engineer. His work in the mining profession was carried on principally in Msxiac and the United States. • In 1888, he married Katherine Haden Krause, of Woolwich, Kent, England, and leaves, besides his wife, five sons and one daughter. During Mr. Malcolmson's long and successful career as a mining engineer, he was connected with the following companies: from 1889 to 1893, with the Michoacan Railway and Mining Co., as mining and mechanical engineer; from 1893 to 1898, in various capacities with the Kansas City Smelting & Refining Co.; after the consolidation of the Kansas City Smelting & Refining Co. with the American Smelting & Refining Co., he remained as manager of the mining department in Mexico of the American Smelting & Refining Co. until 1902. In 1902, he located in El Paso, and took up the practice of his profession as a consulting engineer. While there, he was consulting engineer for the famous and rich Pedrazzini mines at Chispas, in the State of Sonora. He was instrumental in organizing the La Republics mine in Chihuahua, and for a time acted as consulting engineer for the property. He remained in El Paso until 1907 and then moved to Kansas City and became associated with the United States & Mexican Trust Co., as consulting engineer. In 1909, he became connected with The Lucky Tiger Combination Gold Mining Co., as its consulting engineer, and continued in this connection and in the general practice of his profession as consulting engineer until his death.. His general policy in connection with the Lucky Tiger company was always a progressive one and the success of the enterprise can be largely attributed to him and his good judgment. Mr. Malcolmson contributed several articles to the Institute at different times, one of them being on the ore deposits of the Sierra Mojada Mining District, in 1901. Much of his work was in Mexico, and during his long residence in that country he acquired a very thorough knowledge of the Mexican people and their customs. During the revolution, from 1910 to 1916, this knowledge was of great value in connection with his work for the Lucky Tiger company, and often assisted greatly in keeping the property going. Mr. Malcolmson was one of the very widely known men in his profession; he was everywhere held in the very highest regard, and his position among men in the mining profession was an enviable and honorable one. At the time of his death, besides being consulting engineer for the Lucky Tiger company, he was interested in mines in the Miami zinc fields and was acting as consulting engineer for two of the operating properties there. He invested to quite an extent in real estate when he moved to Kansas City in 1907 and his investments in this line proved successful.

Jan 1, 1920

By P. E. Hopkins

In speaking of the economic geology of southeastern Ontario, W. G. Miller and C. W. Knight1 say that "there occurs in southeastern Ontario a variety of minerals and rocks of economic value, probably as great as in any district of like size on the North American continent. Some of these deposits, including marble and trap, are inexhaustible. Others, including talc and iron pyrites, have proved to be of considerable economic importance. From time to time, during the last 50 years, the following minerals and rocks have been mined or quarried with varying success: gold, iron pyrites, zinc blende, copper pyrites, galena, mispickel, magnetite, hematite, talc, actinolite, mica, marble, ophicalcite, feldspar, fluorite, apatite, corundum, graphite and sodalite. All of the economic materials, with, the exception of fluorite, appear to be of pre-Cambrian age. The fluorite veins penetrate the Ordovician, Black River, limestone." Accompanying that report was an article by the writer on the Queens-boro Pyrite Area which includes one of the two working pyrite properties in southeastern Ontario. In the present paper will be given a brief description2 of all the known pyrite deposits in the area which may at some time possess an economic value, with fuller descriptions of the two working mines—The Canadian Sulphur Ore C,o.'s mine near Queensboro, and the Nichols Chemical Co.'s property at Sulphide. The earliest mining of iron pyrites in Ontario was done in 1868 on the Billings property near Brockville. The mines were closed down in 1879 under the assumption that they were exhausted. Many other

Jan 1, 1917

By Y. Jeannin, C. Mannerskantz, F. D. Richardson

Measurements have been made between 1040o and 1300°C of the equilibrium between chromium metal, chromic oxide, hydrogen, and water. The results are in closer agreement with those deduced from recent thermal data than with previous equilibrium values. They lead to the equation ?G°1300°-1600°k = -266,700 + 59.95T ± 300 cal for the formzation of a mole of Cr2O3 from chromium and oxygen. This same equilibrium has been studied with the chromium dissolved in solid iron, and in this way chromium activities in Fe + Cr alloys have been established. The measuremenis show that there are substantial positive deviations from ideality in the a, and b phases, and support the results obtained by Heymer and Kubaschewski against those of other investigators. There is considerable disagreement between existing data,1"4 which is referred to in the Discussion, concerning the equilibrium Cr2O3 + 3H2 = 2Cr + 3H2O [l] There is also substantial disagreement between the results obtained by various investigators5-' who have measured the activities of chromium in its alloys with iron by the Knudsen effusion vapor pressure method. In view of the importance in metallurgical processes of chromium and its oxide and of Fe-Cr alloys, an attempt has been made to study equilib- rium [I] both with pure chormium metal and with chromium alloyed with iron, at temperatures between 1040o and 1300oC. From the work with the alloys it is possible to derive the chromium activities from the relationship

Jan 1, 1963

By V. F. Leferrer

A new process for the treatment of silver crusts from desilverization of lead has been developed by Societe de Penarroya. The zinc contained in the crusts is recuperated by vacuum distillation at low temperature. The use of special retort crucibles is avoided. AT Noyelles-Godault the Parkes process (zinc addition to a silver-bearing lead melt) is used to desilverize lead bullion from the blast furnace. The crust which rises to the surface of the bath is removed and pressed by a well-known process in a press of the Howard type. The pressed crust, called zinc crust or silver crust, contains 10 pct Ag, 30 pct Zn, and 60 pct Pb. It is melted under a salt bed in a small, narrow, and deep kettle heated only in its upper part. A liquid concentrated alloy is obtained which is called T.A.C. in France (triple alliage concentr6) analyzing approximately 25 pct Ag, 65 pct Zn, 8 to 10 pct Pb, and 1 to 1.5 pct Cu. This T.A.C. is a real metallic alloy, completely deoxidized, and can be stored indefinitely. The process used at Noyelles-Godault consists in distilling this alloy in a tight furnace, under low vacuum and at low temperature, so that only the zinc distills and is condensed into liquid form. The residual silver-bearing lead is almost entirely free from zinc and oxidized dross. The vacuum dezincing equipment, see Figs. 1 and 2, consists of: 1) A furnace, constituted of a casing of steel plate lined with refractory bricks, heated internally by means of graphite resistors. The temperature of the furnace is measured by a thermocouple device and controlled by an automatic temperature regulator which acts upon the flow of the current passing through the resistors. Two doors, numbered 1 and 2 in Fig. 2, are provided for, one for charging the T.A.C., the other for tapping the high silver-bearing lead. 2) A condenser, and an ordinary room lined with good heat conductor refractory material. This condenser is provided with a graphite resistor which serves to bring to temperature when starting the furnace. A thermocouple records the temperature of the zinc melt and controls the temperature in the furnace, that is, the flow of current through the resistors, by means of the above mentioned regulator, so that the distillation rate in the furnace does not exceed that of the condensation. The condenser is connected to the vacuum pump by a filter. The whole equipment should, of course, be fluid-tight. The operation is carried out under a vacuum of about 10 mm Hg.

Jan 1, 1958

By E. A. Lawrence

The experiences of Canex Placer Ltd. in establishing vegetation on a lead-zinc tailing pond are presented, hoping others with similar challenges will be benefited. History The tailing ponds are the result of 23 years of mining and milling operations, which ceased in August 1970. Roughly 7.9 million tons of lead-zinc ore were removed in that time. The ponds are located between Salmo River and B.C. Highway 3, about 8 miles north of Nelway near the Canada-U.S. border.

Jan 1, 1975

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the silicides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. MANGANESE AS A SCAVENGER Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

Jan 1, 1928

Abel, Charles Edwin, Student, Univ. of California Los Angeles, Cal. '81 Ames, Marshall B., Blaine-Republic Co Republic, Wash. "81 Anderson, Norman John, Student, South Dakota School of Mines Rapid City, S. D. '82 Angst, Robert A., Jr., Student, Michigan College of Min. & Tech Houghton, Mich. '82 Apgar, James William, Student, Lafayette College Easton, Pa. '83 Armstrong, John R. Box 274, Neosho, Mo. '81 Armstrong, Robert H., Student, Lafayette College Easton, Pa. '81 Arnot, Paul H. 608 S. Acacia St., Compton, Cal. '81 Asel, Philip R., Student, Colorado. School of Mines Golden, Colo. '82 Atkins, William Robert, Student, Michigan College of Min. & Tech Houghton, Mich. '82 Augenthaler, Robert L., Student, New Mexico School of Mines Socorro, N. M. '82 Augustine, Robert W., Student, Alaska School of Mines College, Alaska. '82. Avery, Eugene A., Student, Montana School of Mines Butte, Mont. '82 Babcock, Norwood N., Student, South Dakota School of Mines Rapid City, S. D. '82 Baer, Jerome S., Student, Michigan College of Min. & Tech Houghton, Mich. '81 Baker, Robert C., Student, Pennsylvania State College.. 112 E. Beaver Ave., State College, Pa. '82 Baldwin, William C., Student, Univ. of Illinois Urban, III. '81

Jan 1, 1932

PUGET SOUND SECTION SIMON H. ASH, Chairman, I. F. LAUCKS, Vice-Chairman, CHARLES SIMENSTAD, Sec.-Treas., 425 Lyon Building, Seattle, Wash. GLENVILLE A. COLLINS, JOHN N. POTT. The Puget Sound Section met at the Arctic Club, Oct. 28, 1916, for the annual meeting. Those present were: Chairman Glenville A. Collins, Vice-Chairman H. L. Manley, Sec.-Treas. Amos Slater, Chester F. Lee, R. P. Tarr, G. E. Rockefeller, Simon Ash, Geo. W. Evans, Joseph Daniels, I. F. Laucks, F. C. Greene, Darsie C. Bard, Marcel Daly, Milnor Roberts, F. A. Hill, Percy E. Wright, and as guest, Mr. Coates of British Columbia. After dinner had been served, Chairman Collins called the meeting to order. The reading of the minutes of the last meeting were suspended upon request of the Secretary. The Secretary read the report from the Committee on the Associated Engineering Societies of Seattle. Upon motion, duly seconded, the report was adopted and placed on file. Mr. Lee, Chairman of the Committee. on the Mining Men's Convention to be held this coming winter, gave his report orally, and upon motion the committee was continued. The report of the Secretary-Treasurer was read, received, and placed on file.

Jan 3, 1917

By E. R. Johnson

THE copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the western flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past 15 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. FORMER PLANT The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7 1/2 gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by 1-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55 1/2-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73 1/2-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bin serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 1 3/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7 1/2 McCully gyratory crusher set at 1 3/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73 1/2 by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1947

By K. Leutwyler

The authors present an interesting review of various applications of rather well known theories. Their rearrangement of the original working equations is strictly computer oriented and serves well to that effect; however, the new appearance will be confusing to the slide rule-wielding members of the profession. In reviewing discrepancies existing between calculations made by Baker Oil Tools, Inc. field engineering staff members and computer output submitted based on the authors' program, the following error in concept was discovered in Eq. 4. The authors quote the length change due to helical buckling in the following form We appreciate Kurt Leutwyler's awareness of Archimedes' principle, and concur that the final term in the denominator of Eq. 4 results in a small error. Examples checked revealed less than I ft error, and corrective expressions for the four possibilities of displacement follow. The portion of the denominator within extra large brackets represents the original term W,, = weight of outside fluid displaced per unit length. The authors interpreted the expression "displaced" in general oilfield terminology as a fluid displacement, such as "mud displaced with water, etc." A review of the theory forming the basis for these helical buckling calculations discloses that this displacement is meant to be interpreted in the Archimedean sense, i.e., fluid displaced by the solid body. here the tubing and the seal nipple. Lubinski* illustrated the point by summing moments due to mechanical and hydraulic forces acting on a free body immersed in fluid. This moment summation, always in the Archi,medean sense, yields effects of the real forces, including W,, and the fictitious force on the bending mechanism. I would be interested to hear the authors' comments regarding this theoretical point, which nevertheless is not mute since its lack of recognition seems to result in erroneous calculations. We must not remain mute to Leutwyler's suggestion that these equations, although computer oriented, are confusing to the slide rule engineers. Such input information as density in pounds per gallon, pipe diameters in inches, pumping rate in barrels per minute and pipe length in feet is not confusing to most of us. Yet there may be some rugged individuals in field positions who carry tables of conversion constants and have committed to memory such items as coefficients of thermal expansion and Poisson's ratio; however, even this type of individual would welcome a simplified equation occasionally. M

By G. H. Bishop

The kinetics of the inter granular penetration and embrittlement of [100] tilt boundaries in 99.998 pct pure nickel upon exposure to bismuth-rich Ni-Bi liquids have been determined in the temperature range from 700° to 900°C. The kinetics of penetration are parabolic in time at constant temperature over most of the temperature range. In a series of 43-deg bicrystals the rate of penetration is anisotropic with respect to the direction of penetration into the grain boundaries. In lower-angle bicrystals the penetration rate is isotropic. The rate of penetration decreases with tilt angle at 700°C. The activation energy for penetration in the 43-deg bicrystals is 42 kcal per g-atom independent of direction. It is concluded that the intergranular penetration and embrittlement in the presence of the liquid proceeds by a grain boundary diffusion process and not by the intrusion of a liquid film. This was confirmed by a determination that the kinetics of penetration and embrittlement were the same in the 43-deg bicrystals upon exposure to bismuth vapor under conditions such that no bulk liquid phase would be thermodynamically stable. WhEN solid metals are exposed to a corrosive liquid-metal environment, the grain boundaries are sites of preferential attack. Depending on the temperature, the composition of the liquid, and the composition, structure, and state of stress of the solid, a number of modes of attack are possible. This paper reports a study of the kinetics of intergranular penetration and embrittlement of high-purity nickel bicrystals upon exposure to bismuth which, together with an earlier study by Cheney, Hochgraf, and Spencer,&apos; demonstrates that there are at least two modes of intergranular attack possible in the Ni-Bi system. In the study by Cheney et al., columnar-grain specimens of 99.5 pct pure nickel were exposed to liquid bismuth presaturated with nickel in the temperature range 670" to 1050°C. They found that the majority of the boundaries, which were predominantely high-angle boundaries, were penetrated by capillary liquid films, the attack proceeding by a process which will be termed grain boundary wetting. This process occurs in a stress-free solid when twice the liquid-solid surface tension is less than the surface tension of the grain boundary,* i.e., when 2yLs < YGB In this case the penetration of the grain boundary by the liquid occurs at a relatively rapid rate, resulting in the severe embrittlement of a polycrystalline solid. Grain boundary wetting is a common mode of intergranular attack in systems in which the lower melting component is relatively insoluble in the solid, but the solid has an appreciable solubility in the liquid, for example, the Ni-Bi system, Fig. 1. In systems of this type at temperatures above the range of stability of any intermetallic phases, once the liquid is saturated with respect to the solid so that no gross solution occurs, chemical gradients are small, and surface tensions become major driving forces for attack, provided the solid is stress-free. The results of Cheney et al. appear to be typical of those encountered when grain boundary wetting occurs.&apos; Capillary films were observed in the boundaries after quenching from the exposure temperature. The mean depth of penetration increased linearly with time, and the activation energy for the process was found to be 22 kcal per g-atom. In a study of the Cu-Bi system Yukawa and sinott4 found that the depth of penetration of bismuth into high-purity copper bicrystals of orientations from 22 to 63 deg of tilt about (100) at 649°C ranged from 0.05 to 0.25 in. after a 12-hr anneal. This corresponds to a linear rate of 6 to 15 X 10~6 cm per sec. At the same reduced temperature of 0.68 the rate for the Ni-Bi system&apos; was 7 x lo-&apos; cm per sec. In another study of the Cu-Bi system, Scheil and schess15 determined the kinetics of grain boundary wetting in hot-worked commercial rod. While there were several complicating factors present in this study, there is general agreement with the above results. The kinetics of penetration were linear, the activation energy was 20 kcal per g-atom, and at 650°C the rate of wetting was 2 to 5 x 10-6 cm per sec. The rate of wetting in the A1-Ga system6 is somewhat

Jan 1, 1969

By William V. Kotlensky

PYROLYTIC graphite may be represented by a stack of overlapping, wrinkled sheets with the graphite basal planes more or less parallel to the deposition surface. Previous work1" has described two stages in the deformation above 2600°C produced by applying a stress parallel to the deposition surface. The first stage occurs at deformations less than about 15 pct and involves dewrinkling accompanied by basal-plane slip and basal-plane reorientation. The basal planes are not perfectly

Jan 1, 1965

By A. G. Loomis

IT is only within the past 10 years that serious attempt appears to have been made to improve rotary drilling fluids by the application of the principles of colloid chemistry, although the use of chemicals to control the rheological properties of clay slips has long been known in the ceramic industry. The main difficulty apparently lay in the lack of a complete analysis of all of the functions of a drilling fluid in the drilling of the well, together with the lack of adequate consideration of how colloid science could be applied to secure these ends, and particularly how apparent antithetical properties of the fluid could be compromised. Thus one analysis1 of the many requirements of a drilling fluid proved conclusively that the viscosity should be low, in order that cuttings and entrained gas might be eliminated effi-ciently in the settling ditch, while the loss in carrying capacity accompanying low viscosity could be regained by increasing either the density of the mud or the upward velocity of the mud stream in the annular space of the well, and the danger of sticking of the drill stem due to rapid settling in case of enforced suspension of drilling operations could be eliminated by enhancing the thixotropic properties of the fluid. The desired properties of the drilling fluid having thus been established, it was a natural step to treat the fluid with vis-cosity-reducing chemicals, such as salts of weak organic acids1,2-for example, sodium tannate or gallate-and to adjust the pH to the alkaline side to such a degree of thixo-tropy as would give low viscosity and low yield point under the conditions of flow prevailing in the settling ditch, but rapid gelation and high yield point when quiescent in the annular space during shut-downs. In fact, flow in the settling ditch should be just short of turbulent while flow in the well, together with the flow of mud past the cuttings, is practically always turbulent. The use of chemicals other than those mentioned, such as Calgon (sodium hexametaphosphate) and certain other phosphates together with sodium tannate, has now become standard practice and it is the consensus that this method of treatment has proved to be an important step in the development of the art of drilling oil wells.

Jan 1, 1940

By C. H. Herty

Almost every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe&apos;s Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gauging of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanliness of forging steels, both carbon and alloy. In this problem the oxidizing characteristics of the slag are of prime importance.

Jan 1, 1940