Search Documents

By D. S. Newton

Introduction Historically the production of zinc dust has been based upon residual and secondary zinc. Using horizontal retorts filled with diecasting scrap, galvanizers drosses and sweater billets, dust has been produced by condensation into static condensers on a 24 hour cycle. Although fairly flexible as regards input materials the process is not amenable to close control of the product, is labour intensive and unless carefully run can cause fume problems. With a steadily increasing demand for zinc dust of consistent properties and higher quality there is a demand for an improved method of manufacture in which dust can be produced continuously and which is capable of close control thus ensuring a minimum amount of oversize or unsaleable material. The Process in use in the works of Imperial Smelting Corporation (Alloys) Ltd. in England, and in Canada and Holland, satisfies the criteria stated above, and has proved to be easy to control with a minimum labour demand.

Jan 1, 1970

By B. Woyski

MANY writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deoxidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gases is more difficult to overcome. The regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes are the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer' lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere.

Jan 5, 1922

By John D. Siddle

Efficient energy utilization in the electrolytic zinc process, relative to other zinc processes, is one of the reasons for its wide adoption in recent years. Designers and operators of electrolytic zinc plants have pioneered process improvements, new equipment, and operating techniques to conserve energy. As energy costs advance still higher in the future, and competitive pressure against the less efficient producers increases, these or alternative energy-saving methods will be looked upon as a necessity for economic survival. Estimated energy savings which may be achieved by various equipment and techniques are included.

Jan 1, 1977

By J. J. Thomas, J. H. Nead

This investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 1, 1922

By J. H. Nead, J. J. Thomas

This investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 1, 1922

By D. J. Jr. McAdam

RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers. 1,2,3,4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The endurance limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

Teamwork: The famous first sentence of an essay en- titled Aphorisms, by Hippocrates, is as follows: "Life is short, the Art long, opportunity fleeting, experience treacherous, judgment difficult." The future of science does not depend so much on the number of scientists or the number of colleges, but rather on the individual qualities and the degree of perfection of a limited group of leading scientists and colleges. These are individual factors which require inherent talent which in turn is a condition evolved after generations of culture. Thus, very elaborate higher education for indiscriminate masses of humanity or students may not necessarily show the expected results. In other words, it is possible that higher specialized education should be given only to the few talented individuals, and their capacity and worth should be judged by as highly qualified and talented teachers. Quality is the greatest of all competitive aids. An essential qualification that must be possessed by a quality mineral industries college is a high caliber teaching staff, for the mineral sciences will advance in the coming years only if the leading minds of today are made avail- able as the mental springboards for our scientists of tomorrow. Mineral industries schools are finding it increasingly difficult to maintain a high caliber staff of instructors and administrators in competition with private business and governmental demands for similar

Jan 1, 1950

By E. A. G. Colls

Discusses corrosion in Trail chemical plants producing ammonia, sulphuric, nitric and phosphoric acids, ammonium phosphates, sulphate and nitrate, together with miscellaneous allied material problems and their solution using erosion or corrosion proof materials. Conclusion, that for work of this nature, most costly material may well be cheapest in the long run.

Jan 4, 1950

By David R. Mitchell, Byron M. Bird

THE revision of this chapter has presented a problem in that heavy-medium jigging has come into the picture since the chapter was originally written (seven years ago), a practice in which an artificial medium is built up and maintained in the jig circuit. As this development makes the jig a "true" heavy-medium process, the method belongs in the chapter dealing with such processes. Although putting this development in its proper position in the book involves some repetition, this seems to be the best procedure, and it has been followed. As the chapter on jigs in its original form was intended to be more or less a handbook on jigging for the use of the practical man, and the great bulk of the material therein is still generally applicable, the text has been re-used in large measure. Two major changes should be noted: (1) the portion of the text relating to the refuse-withdrawing mechanism of the McNally-Pittsburg jig has been entirely rewritten, and (2) a description of the hutch valves on the Jeffrey jigs has been added. Jigging is the stratification of a mass of solid particles in upward and downward pulsations. The stratification usually is effected in a rectangular open-top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (2) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through 3/4-in. to 0, and mixed sizes of ores down to 7/32-in. to 0and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 per cent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and flat. It is handling simple separation problems and difficult separation problems.

Jan 1, 1950

By Frank F. Aplan

In looking into the crystal-ball scene of minerals beneficiation for 1970 and beyond, an impartial observer becomes con- fused as to what has been done and what is possible in the way of improvements. The mining official must balance the burden which is being shouldered by the mineral industry for maintaining our environment in its pristine state on one hand, with the solid advancements made in technology and cost savings on the other hand. Then the official wonders if this is really the criterion for judging overall performance today. As a prospective engineer, Dave Bolles sees it this way: "Specialization has caused many engineers to subordinate everything to doing their job the cheapest and fastest way. In the future this won't be enough. The engineer in the mineral industry will be responsible not only for mining, concentrating and smelting, but also for the resultant wastes- the mine dumps, the tailing dams and the slag piles." (See Drift on page 63).

Jan 1, 1971

CHARLES CATLETT, Staunton, Va.-A great many important things have been said in an interesting way but the most startling, to me, is that for 25 years, the price has been in the neighborhood of $1.00, with a minimum of 86 cents and a maximum of about $1.25. It is evident that during all that time the price was inadequate. The amount paid to be divided between the land owner, the capitalist, and the laborer was too limited or too irregular to permit of a healthy condition; yet it is evident that the enormous industrial development of this country was fostered by this very cheap coal, probably the cheapest that has been provided in quantity in any country. I entered the coal business when the price was lowest and my interest and sympathy went out to the man who spent his days in the dirt and foul air of a mine and I was filled with schemes for helping. But at the end of the year, after exercising every economy and in blissful ignorance of proper depreciation and obsolescence, there was still only a profit of 1 cent per long ton for what I think is one of the best coals in the world, the best grade of New River coal. We are now paying a great deal more than we did a few years ago and probably will continue to pay more for some time; but any one who thinks we will not have low prices again is very young or very forgetful. Yet we must have larger profits if the industry is to be healthy, if the three parties to the production are to get adequate returns and be in shape to provide the improvements which will be needed to take the place of and supplement the man-power. This will come when the men are making so much money that the operator wants to replace the man by a machine, and when the operator is making so much money as to be in a shape to make the improvements. He will not put in machinery unless the machinery will save money. We have got to pay a higher prime cost for coal, but engineering skill will teach us how to handle it better and use it more economically, and the ultimate result ought to be of advantage to the public.

Jan 3, 1920

By C. N. J. Wagner, E. N. Aqua

The bee alloys of the terminal solid solution of rhenium in niobium were investigated by X-ray diffraclion methods. The analysis of the broadening of the powder pattern peaks from the niobium-rich alloys, cold-worked by filing, showed evidence for faulting on (211) planes. The alloys with larger rhenium concentrations were brittle, and fractured when filed. The analysis of the shapes of the diffraction profiles from powders produced by hammering with steel plates) of these brittle alloys indicated that the broadening was due predominantly to platelets bounded by clibe planes. This result was consistent with the Laue patterns from single-cleazlage facets which showed evidence for clearage fracture on {100} planes. The influence of faulting on the mechanical properties of face-centered cubic (fcc) metals and alloys, i.e., how faulting affects the various dislocation configurations in fcc metals, is well-known.' The important question is whether or not faulting occurs in body-centered cubic (bcc) metals and alloys, and, furthermore, if faulting does occur, to what extent it affects the mechanical properties. Theoretical calculations indicate that the stacking-fault energy is rather high in most bcc metals.2 The results of sev-eral studies using transmission electron microscopy have indicated that faults are present in well-annealed and lightly deformed bcc metals and alloys, such as tungsten,3 vanadium,4 and Mo-Re alloys.5,6 These faults, as have been observed, may be stabilized by the presence of interstitial (C,N,O) atom segregation to the extended dislocations. In addition, there is considerable X-ray diffraction evidence for faulting in bee metals,7-8 using the same techniques that were successful for the study of faulting in fee metals and alloys.7 This X-ray diffraction method is currently the only technique applicable for the investigation of faulting in metals with high stacking fault energies, i.e., when severe amounts of deformation are required to produce sufficient amounts of faulting to be detectable by X-rays. The thinned films of heavily deformed metals will become opaque in the electron microscope due to the high dislocation densities present. In a previous investigation of faulting8 in bee metals of group Vb and VIb, the authors observed that niobium was ductile when filed at room temperature, and showed the highest density of faults on the (112) family of planes. A niobium-base alloy system was therefore chosen to study the effect of alloying on the occurrence of faults in a bcc alloy. There is a large range of terminal solid solubility of rhenium in the alloys of the bee refractory metals. All of the Group VIb-rhenium alloys, i.e., Cr-Re, Mo-Re, and W-Re, exhibit solid solution hardening without loss of ductility.9 In fact, the ductility reaches a maximum for alloys with compositions near to the limits of solubility. This enhanced ductility has been attributed to the lowering of the stacking-fault energy in the alloy; i.e., the increased amounts of twinning provide an additional mode of deformation, resulting in the observed high ductility.' Because of this demonstrated effect of rhenium in bee alloys, it was decided to study a series of alloys of Nb-Re. Using the same X-ray diffraction methods as described in the previous investigation,' one is able to identify the possible causes of broadening of the powder pattern peaks, e.q., particle size, microstrains, stacking faults, and/or twin faults. The separation of these various contributions to the measured peak shape is accomplished by the Warren-Averbach analysis.7 I) EXPERIMENTAL PROCEDURE A series of seven bee solid solution alloys containing from 2.5 to 21.5 at. pct Re (remainder niobium) were prepared at the General Electric Research Laboratory. Buttons, weighing 25 g, were alloyed from electron-beam-melted niobium chips and random rhenium sheet by arc melting in a water-cooled copper crucible, under an argon atmosphere. The buttons were inverted and completely remelted to promote homogenization. The nominal alloy compositions are listed in Table I. Samples of the cold-worked alloys were obtained by filing to produce a powder for the X-ray study. Alloys too brittle to be filed were hammered with steel plates. The resultant filings or brittle impactings were screened through 150-mesh classifiers and compacted to the required shape for the diffractometer holder. The X-ray diffraction peaks were automatically recorded by fixed time counting at uniform 28 intervals, or by continuous registration with a ratemeter. In all cases, the (110)-(220) and (200)-(400) pairs of peaks and the (211), (310), (222), and (321) reflections were measured on a GE-XRD5 diffractometer using CuKa radiation with nickel filter or MoKct radiation and a LiF monochromator in the diffracted beam. The first part of the data reduction, completed with the aid of a series of programmed computations,10 was the analytical resolution of the Kol component of the diffraction profile. Subsequent computations were then made with reference only to the resolved Kol peak shape. These included the measurement of the

Jan 1, 1967

Continued Discussion of the papers of Van Hise, Emmons, Weed and Lindgren, Bans., xxx., 27, 177, 424, 578. See also the papers of Vogt, Kemp, Rickard, Blake and Lindgren, at pp. 125, 169, 198, 220, 226, and also the final contribution of Prof. Van Hise, p. 284 of the present volume. All the foregoing, together with the discussion here following, are included in the special volume, "The Genesis of Ore-Deposits," issued this year by the Institute. H. Foster Bain, Des Moines, Iowa (communication to the Secretary):* The zinc- and lead-deposits of the Mississippi valley, which it has been my fortune to study, give particularly good examples of many of the principles of ore-deposition formulated by Prof. Van Hise. Perhaps there is nowhere clearer evidence supporting his fundamental tenet., that ore-bodies are to be regarded as a result, and as merely one of the phases, of the work of underground waters. The facts regarding the mines of the upper Mississippi valley have been given in some detail for Wisconsin by Prof. Chamberlint and, more recently, for the mines west. of the Mississippi by the Iowa Geological Survey.‡ Fortunately, also, the processes of underground water-circulation have been studied in some detail in connection with the investigation of artesian waters throughout the region.$ In Missouri and Arkansas the mines and ore-bodies have been much studied ; but the general problems of the circulation of underground waters have been neglected. During the season just closed the writer has been engaged in a re-study for the United States Geological Survey of the zinc- and lead-deposits of the Ozark region, with special reference to those of the . Joplin area; and his full report is now in preparation. It has been interesting to note how fully the statement that the orebodies result from the general action of underground waters is

Jan 1, 1902

The finding of gold, in enriching quantity, along the streams that issued from the western foothills of the Sierra Nevada was the prelude not only to the birth of an organized mining industry in California but to the intensive exploration of the entire Pacific slope; it presaged the feverish exploitation of the mineral resources that the ubiquitous prospector soon uncovered all over our western domain. At first when this migration began, as typified by the rush of 1849, there was no time to examine the signs of ore that were to be detected along the track of adventure, and, it must be added, not many in that motley crowd of gold-seekers were qualified to interpret the signs if they had lingered to look at them. Such intelligent curiosity as a few of them possessed was directed to the finding of gold chiefly, if not exclusively; and their good sense in this respect can not be impugned, because in a new and remote country the less valuable metals and minerals are unlikely to be worth the winning. Many of those that came to California crossed the alkaline wastes and sagebrush prairies that extend between the Great Sal? Lake and the ramparts of the snow-clad Sierra; when coming overland they found it convenient to halt on the eastern slope and to pitch their camp in the valley of the Car- son river before they began the tedious ascent of the mountains and the final entry into the land of gold. One of the trails most used by these immigrants followed the Carson river to the mountain meadows south of Lake Tahoe and then descended among the pine-woods of Placerville, where they went to work with pan and shovel in the gold-bearing streams

Jan 1, 1932

By M. W. Bartley, Hugh M. Roberts

SUBSTANTIAL deposits of Bessemer hematite have been found recently by drilling beneath Steep Rock Lake, Ontario, which is situated in the northern part of the Lake Superior Region. It will be practicable to divert the waters flowing into this lake and develop open pits on the upper part of two large ore bodies by damming off and pumping out the water in the part of the lake in which they occur. Ultimately, the bulk of the ore will be mined by underground methods. Owing to the generally massive nature of the rocks in the area, no underground flows of major consequence are anticipated after diversion of the lake. The Steep Rock deposits are attributed in origin to hydrothermal replacement. They were formed, for the most part, along an unconformable, brecciated contact between the Steep Rock limestone and an overlying younger volcanic series. The replacing solutions came in as igneous after-effects, following upon the intrusion of basic igneous rocks that invaded the hanging-wall volcanics. It is believed that this took place in a geological period roughly equivalent to late Middle Huronian, which was the period when the most extensive iron-bearing rocks of the Lake Superior Region were formed. Comparison is made with other deep-seated iron-ore bodies in the Lake Superior Region, the origins of which are ascribed in the discussion to hydrothermal replacement.

Jan 1, 1943

By Eizo Yabuuchi, Yukito Imanaga

INTRODUCTION In treatment of mine drainage, it is well known that the neutralization by calcium carbonate is far better than by slaked lime because of cheaper cost and better precipitability of its deposit. However, in case of iron ion contained in the mine drainage consists of ferrous salt, the ferrous salt must be oxidized to ferric salt before neutralization, because the ferrous salt does not react with calcium carbonate. At Yanahara Mine, during the period of 1950 through 1956, ferrous ion in the mine drainage had been oxidized to ferric ion, simultaneously neutralized by adding calcium carbonate into the aerated drainage. During the period of 1961 through 1974, after passing through many kinds of treating methods, the neutralization had been carried out by addition of calcium carbonate into the drainage after oxidized its ferrous ion to ferric by using nitrous gas as an oxidizing catalyzer. Meanwhile we had made an experiment on the oxidation of ferrous ion by utilizing iron bacteria, and developed a method which oxidized ferrous ion in large quantities briefly by cultivating and concentrating iron-oxidizing bacteria. Since 1974, we have been operating successfully for treating the drainage at Yanahara Mine by means of utilizing these bacteria.

Jan 1, 1976

By L. E. Mannion

Sodium carbonate (soda ash) is one of two principal commercial alkalis. Its principal competitor is sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines and solid salts provided impure soda for early glassmaking. Until the 19th century, soda ash (as well as potash) was recovered mainly by leaching wood or other plant ashes. In 18th-century Europe, for example, leaching seaweed ash with hot water produced a brown laundry lye. One of the better grades of this material was a Spanish product, barilla, which analyzed 24 to 30% Na2CO3 (Hou, 1942). The modern chemical industry was born in 1691 with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. English industry used this process extensively in the 17th and 18th centuries. The next major advance was in 1863, when Ernst Solvay devised the ammonia-soda, or Solvay process. The first of many Solvay plants was built in 1874. These supplanted the LeBlanc method and dominated worldwide soda ash production until 1974, when mined sodium carbonate became predominant. Although considerably less important until recently, natural sodium carbonate deposits historically have supported small soda ash operations throughout the world. Shortages during World War II stimulated production of "natural" soda ash from such deposits, particularly at Searles Lake, CA and Lake Magadi, Kenya. More spectacularly, increased production from the vast trona deposits in Wyoming has virtually supplanted the Solvay process in the US. Principal producers of natural soda ash as well as the character of the source deposits are listed in Table 1. [ ]

Jan 1, 1983

By Donald H. McLaughlin

THE primary function of the mining engineer is to find mineral deposits and fuels in the accessible rocks of the earth and to recover them for the vast needs of our complicated civilization. On him has been placed the responsibility for the exploitation of the nation's and world's mineral resources. The degree to which the minerals of the earth have been utilized serves to an extent as a measure of man's material advancement, as well as an index of the relative strength of nations. The natural endowment of lands, varies greatly, but the intellectual energy of a people is revealed by the way in which they take advantage of their heritage of minerals or reach out to less developed regions by exporting their engineering skill as well as capital to secure the raw materials they need.

Jan 2, 1953

By David R. Mitchell, E. A. Reilly, G. R. Gardner, F. P. Lasseter

THE methods that may be applied to the treatment of slurries and water, as these are related to practical coal-preparation problems, are concerned essentially with the movements of solids suspended in water. It is assumed that there are no fundamental differences between the principles involved in the treatment of coal slurries and the phenomena encountered in general mineral-dressing practice, and the latter are-presented in some detail. Basic principles are correlated with present practice for both the anthracite and the bituminous coal fields, and methods are discussed which are designed to utilize best all the material subjected to treatment and suggest a sound approach to the solution of problems relating to the return of clear water to process or to streams. In order to approach the practical phases of the subject with sufficient understanding of the basic principles, it is necessary to discuss two types of phenomena that are applicable. The first is flocculation and the second is sedimentation. Descriptive matter is given covering the various methods and types of equipment employed to conduct these operations, with emphasis on their application to water and coal-slurry treatment. DEFINITION OF TERMS Definitions of terms are consistent with modern developments, and conform, in general, with their usage in mineral-dressing practice. Because of variations in coal-preparation methods, it is impossible to define a rigid upper limit of particle size for a coal slurry or sludge which will apply generally. Limits vary somewhat with the particular treatment method employed at a given plant. For purposes of definition, this limit is chosen as the particle size for which preparation methods such as Chance comes and jigs are usually dispensed with, and other methods, such as the Hydro-tator, tables, and froth flotation, are employed. Generally the limit will be 10 to 6 mesh.

Jan 1, 1950

By James G. Blaine, David A. Summers, L. John Tyler

There has been a considerable amount of research developed which shows that the close contour cutting of an excavation prior to removal of the central core will increase ground stability while concommitantly, reducing the number and size of blastholes required to create the excavation. To date, the industrial development of this technique has however, centered on the development of equipment based on simple cutter movement and mechanical rock cutting. The advent of reliable field operable high pressure waterjet cutting equipment with the very low reactive force required to hold the head in position has opened the way for a much smaller and more manueverable system. The advent of small, micro-computers allows the programming of accurate profiles for cutting tools on excavation equipment. The combination of these two technologies will allow the generation of complex as well as simple, excavation profiles and lead to the potential pre-support of the opening before major excavation is completed. A brief description of the necessary components and their functions is encorporated in the initial prototype design as given.

Jan 1, 1984