Search Documents

By C. L. Meyers, J. L. Lytton, T. E. Tietz

The recovery of tensile flow stress of 99.995 pct A1 under conditions of elastic strain and plastic creep straining was investigated using a fractional recovery parameter. Tensile straining was conducted at room temperature to a true strain of 0.10, and recovery treatments were made under stress in the temperature range from 80° to 198°C. Whereas elastic strains had no appreciable influence on flow-stress recovery, plastic creep straining was found to accelerate the recovery process. Although higher creep stresses gave greater recovery for a given time and temperature, it was found that lower stresses produced greater recovevy at equal ALTHOUGH many studies have been made to date on the recovery of metals from the cold-worked creep strains above about 0.005. This effect was attributed to the coarser, and therefore weaker, substructure developed during creep at the lower stresses. The activation energy for recovery during creep straining at 2075 psi between 160" and 198°C was found to be 25,000 cal per mole. This value was not significantly greater than the value previously obtained for no-load recovery. The activation energy for creep at 2075 psi between 160" and 198°C was 34,000 cal per mole, a value significantly greater than that for recovery under the same conditions. state, little is known concerning some important aspects of recovery behavior. One such area is the effect concurrent strain has on the recovery process. Since metals in structural applications at high temperatures are under stress, the possible effects of the resulting elastic and plastic strain on recovery may be of significant importance.

Jan 1, 1962

By G. Campbell

The paper by M. Lonoff looks at the importance of byproduct prices on copper production. The paper develops several interesting points on this topic, but there are some points in the theoretical discussion that could use further development. A couple of these theoretical topics will be considered here using the paper's framework of assumptions without concern about how realistic the assumptions are for the copper industry. Lonoff’s theoretical model is based on a static, homogenous world where all copper/byproduct deposits are identical, and these deposits are the main source of these metals. Due to the importance of the byproducts to the production decision, the term coproducts will be substituted for the term byproducts to reflect more accurately this condition. The conclusion is drawn that a rise in coproduct prices necessitates a decrease in copper prices because copper production is increased as a consequence of increased coproduct production. The observation that real world behavior does not always follow this pattern is dismissed as "speculation." However, it can be easily shown that within this simple framework market forces might create the observed behavior. The key question to be answered is what causes coproduct prices to rise. Three possible cases will be used as illustrations. The first case is the one implicity assumed by Lonoff. Here, the demand for coproducts increases at all prices (an outward parallel shift of the demand curve) with the demand for copper remaining constant. As reported in the paper, the results are higher coproduct prices, an increase in coproduct production, and lower copper prices due to the resulting increase in copper production. The second case is when the supply of coproducts are constrained-leading to higher market prices. Copper production, as required by the simple model, is also reduced which

Jan 1, 1984

[Year of Election . 1944 .WALTER HULL ALDRIDGE New York. N. Y 1944 . SELWPN GWILLYM BLAYLOCK Trail. B.C.. Canada]

Jan 1, 1946

By W. T. Stuart

THE increased demand for iron ore has necessitated a re-examination of ore-bearing lands on which the presence of water previously has indicated hazardous and expensive operating conditions. In view of the importance of iron ore production to the national economy and defense, the Ground Water Branch of the U. S. Geological Survey, in cooperation with the state of Michigan, began a study of mine drainage in the Iron River district in 1945, and later extended the work to the Marquette district. The purpose of these studies was to define the principles involved in the movement of surface and ground water toward the mined areas, with the hope that the information obtained in the research would lead to the development of methods of water control and to a reduction in the total mining costs. Not only are the direct costs of drainage increasing, but also the indirect operational costs of working a wet mine are becoming a larger proportion of the total mining costs. For some wet mines the direct costs of pumping and drainage may range from 35 to 40Ø per ton of ore produced, but the indirect costs due to handling wet ore and controlling the water may be five to ten times this amount. The methods of study were formulated as the work progressed, and inasmuch as they were the first large-scale studies of their kind, they should serve as a guide for the solution of similar problems in other mining areas. The Iron River district was chosen for a pilot study because in this district the longest records of mine pumpage and water-level observations were available, including, as they do, the records for the Homer mine of the M. A. Hanna Co., where pumping from surface wells began in 1930. The results of the first investigation by the Michigan Department of Conservation have already appeared." The first section of the report on a similar study of the Marquette district, which was started in 1948, will be published this year. Methods of Study In an effort to reduce the flow of water into the mine workings in the Iron River district, about 4500 gpm was pumped from the bedrock being mined and about 9000 gpm from the glacial overburden. In the Marquette district in the vicinity of Ishpeming and Negaunee, about 5000 gprn was pumped from the bedrock and about 4000 gpm was pumped from the glacial overburden. Where the water was pumped only from the bedrock, the rate of pumping ranged from a few hundred gallons per minute in the dry mines to many hundred gallons per minute in the wet mines. In each district, pumping from the overburden was localized on a few properties where costly pumping installations had been made and the expenditures for power had been large. In each district a comprehensive ground-water investigation was made of the whole area, involving the collection and interpretation of all the available data bearing on the source and quantity of water to be controlled. Although it is not the purpose of this paper to discuss the methods of making a ground-water investigation, it should be pointed out that a drainage study follows a pattern of engineering analysis that determines the occurrence, source, movement, disposal, and quantities of water involved. The investigation in the iron-mining districts of Michigan began with the construction of a map of the buried bedrock topography. Because the ground-water reservoirs occupy the low points in the bedrock basins, this map gives information concerning their areal extent, depth, shape, and degree of interconnection. The depth to water in the drillholes and wells indicates the altitude to which the ground-water reservoirs are filled, and the logs of the material penetrated in the drillholes and wells indicate the general character of the materials filling the reservoir. The slope of the ground-water surface indicates the direction of flow through the reservoir, the water movement being from the points of higher altitude to points of lower altitude. By analysis of the rise and fall of the ground-water levels in response to additions of water through recharge and to changes in the rate of discharge through pumped wells, estimates of the total quantity of water in storage and of the rate of flow through the reservoir

Jan 1, 1952

By K. E. Manchester, A. H. Clark

Hall measurements have been made on three groups of silicon samples, which were implanted with boron, aluininunz, and phosphorus ions. Boron and phosphorus implants show essentially bulk properties when annealed under previously determined conditions, i.e., 15 min at 80O°C for boron and 10 mirz at 600°C for phosphorus. Bulk properties were also observed in alu?rrilzum-implanted samples when ion concentrations were below 1015 cm-'; however, strange low- terrzperalure behavior and a falloff in cavrier concenlralion was observed for sarnples with ion concenlration abozle loL5 ern-'. This can be attributed to solid-solubility effects since the average bulk concentration f0.r the sample exhibiting bulk properties was below the reported solubility limit for aluminum, while the other samples were above the limit. A detailed study of the annealirzg process indicates that mobilities reach bulk c~alues in phosphorus implants at 250DC, in alutninurn ivnplanls a1 500°C, and in boron implants at 700°C. A simple rnodel has been proposed to fit the annealing data. THE technique of semiconductor doping by direct injection of energetic ions is being actively investigated at this Center. Previously published results from this laboratory have been concerned with the investigation of implanted profiles in silicon and the electrical properties of the resultant p-n structures.1'2 Diode properties have been reported for junctions produced by implantation of boron ions and aluminum ions in n-type silicon and phosphorus ions in p-type silicon. Reverse current characteristics, as well as electron diffraction data, have indicated that the damage to the structure produced by the energetic ions during the stopping process can be minimized by a gentle anneal. The time-temperature conditions for this process have been determined by sheet resistivity studies.3 Electrical profiles of implanted phosphorus ions which have been determined by a differential sheet conductivity technique are based on the assumption that the carrier mobilities and activation energies for ionization are the same as in bulk silicon. These assumptions have been substantiated experimentally by measurement of Hall constants and resistivities of these implanted structures and the results are presented herein. After establishing the bulk property equivalence of the annealed layers, a more detailed examination of the annealing process was undertaken. The sheet resistivity technique initially used to determine anneal conditions has been broadened to include Hall constants and mobility behavior with anneal conditions. PROCEDURE The three groups of samples prepared for Hall measurements were implanted with mass-separated beams of boron, aluminum, and phosphorus ions. Ion concentrations are equivalent surface concentration and they have been determined from beam current measurements during implantation. Implant conditions for the samples are shown in Table I. In all cases, the samples had previously been angle-lapped on one edge and the junction delineated with an HF-copper sulfate solution. The surfaces of the implanted regions of the samples were exposed to the delineating solution and in the case of the "n"-type phosphorus-implanted areas it was later discovered that a finite amount of surface could be etched by this solution. This is discussed in the section on results. The implanted samples were ultrasonically cut into the conventional six-probe configuration shown in Fig. l.* In the annealing studies, for which the meas- urements were taken at room temperature, the sample holder was a Bakelite jig incorporating tungsten mechanical probes. The other measurements were taken using a conventional liquid-nitrogen cryostat, in which the temperature could be varied from 77" to about 400°K. For these measurements, 10-mil aluminum dots were evaporated onto the samples and alloyed with the silicon at 530°C for 15 min. The samples were then mounted in flat-packs, and gold wires were bonded to the aluminum dots. The electrical measurements were made with either a Leeds & Northrup K-5 Potentiometer, a Keithley 147 Nanovolt Null Detector, or a Keithley 601 Electrometer. No external bias was applied to the substrate. There is an inherent self-biasing arrangement at one or the other of the current contacts (depending upon the polarity), and this suffices to limit the current flow to the implanted layer. The magnetic field was generated by an A. D. Little electromagnet. Except for occasional checks of linearity of the Hall voltage with

Jan 1, 1969

By Nicholas J. Grant, Irmgard Rump, Bill C. Giessen

The system W-Hf was determined by use of metal -lographic and X-ray methods. The only interrnetal-lie phase W2Hf melts peritectically at 2650° ± 50°C. A eutectic between W2Hf and ß-Hf solid solution exists at 78 at. pct Hf arul 1930º ± 10°C. The addition of tungsten loulers the hafnium transfornzation; there is a eutectoid at 93 at. pct Hf and 1560°C. The solubility limits of the terminal solid solutions were determined. At the beginning of this investigation, the system had not been elaborated; only crystallographic work had been done to determine the structure of the occurring intermetallic compound W2Hf, and a certain analogy to the system W-Zr was to be expected. Special emphasis was placed in this program on the Hf-rich part of the diagram. Following the completion of our experiments, a phase diagram was suggested by Braun and RUdY.1 EXPERIMENTAL METHODS The investigation utilized tungsten powder supplied by the General Electric Co. with a purity of about 99.9 pct and hafnium crystal bar of about 97.7 pct purity, 2.3 pct Zr, supplied by Foote Mineral Co. Typical analyses are given in Table I. The procedures followed were identical with the ones described for the Re-Nb diagram.' Tungsten powder was compacted at 16,000 psi and the necessary amount of hafnium was added in the form of small pieces cut from the crystal bar, with a reasonable excess of tungsten powder to make up for powder losses on melting. High hafnium or tungsten melts were prepared from premelted tungsten and hafnium or by employing master alloys. The melting was done in a Heraeus arc-furnace under argon. Melting and remelting up to 8 times resulted in fairly homogeneous alloys. No weight

Jan 1, 1962

COLUMBIA SECTION Holds four sessions during year. Annual meeting in September or October. S. S. FOWLER, Chairman, J. C. HAAS, Vice-Chairman, LYNDON K. ARMSTRONG, Secretary-Treasurer, 720 Peyton Bldg., Spokane, Wash. W. H. LINNEY, J. F. MCCARTHY. A special meeting of the officers of the Columbia Section was held in Spokane, Wash., Jan. 10, 1918, for the purpose of organizing and nominating members to the principal committees of the Section. Present: J. C. Haas, Vice-chairman; W. H. Linney, Past Chairman; and L. K. Armstrong, Secretary. J. F. McCarthy, Wallace, Idaho, was appointed fifth member of the Executive Committee. The following were appointed to the Membership Committee: R. M. Betts; for Oregon; W. J. Hall, for Idaho; J. M. Porter, for Washington. A member for British Columbia will be appointed later. The following were appointed to the Committee on Papers: Prof. F. A. Thomson, Moscow, Idaho; Prof. L. 0. Howard, Pullman, Wash.; H. S. Lee, Rye Valley, Ore. A fourth member, representing British Columbia, is to be appointed later. The following members were appointed representatives on the Executive Committee of the Spokane Engineering and Technical Association: J. C. Haas, W. H. Linney, F. A. Ross, L. K. Armstrong. The Treasurer reported a deficit, resulting from the participation of the Section at the Northwest Mining Convention in 1916. It was recommended that the Institute be petitioned to make good this deficit, in addition to the usual annual allowance. The members of the committee who were present expressed their desire to be of greater service in the present war, and discussed at some length the possible means of carrying out their desires. It was later decided to reopen the subject at a subsequent meeting of the Section, or to present it to the Executive Committee of the Spokane Engineering and Technical Association for discussion and cooperative action. L. K. ARMSTRONG, Secretary.

Jan 3, 1918

By J. C. Danko, R. D. Stout, A. H. Holtzman

The deformation characteristics of pearlite have been studied by light and electron microscopy.1,2 In the electron-microscopic work, deformation was found to take place by 1) ferrite slip which is parallel to the lamellae, 2) slip transverse to the lamellae with both cementite and ferrite deforming, and 3) ferrite-cementite interfacial slip. The transverse slip gives a step-like appearance to the lamellae in light microscopic work. It was thought that spheroidization of deformed pearlite would commence at the regions of maximum cementite deformation, the "stepped" areas. Although there is no possibility for seeing slip in the microstructure if the specimen is polished after deformation, the step-like appearance of the lamellae clearly indicates the transverse deformation. Thus, the areas of cementite deformation are apparent after polishing and the effect of deformed areas on spheroidization may be studied by the usual metallographic techniques. This note reports the result of a metallographic investigation which substantiates that spheroidization begins in the "stepped" areas. An AISI 1080 steel was normalized, re-austeni-tized at 1040°C, and isothermally transformed at 700 ± 4°C for 4 hr. Cubes, 5 mm to a side, were compressed between parallel plates to strains of 20, 40, and 50 pct. After deformation, specimens were heated to 600, 650, and 700°C; withdrawn at increasing time intervals and examined metallo-graphically for the percentage and distribution of spheroidite. The percentage of spheroidite was determined by lineal analysis. A micro structural region considered as spheroidized was one in which a lamellar skeleton was not distinguishable. Table I gives the times necessary for 95 pct spheroidization for each condition of strain and annealing temperature. Fig. 1 shows the microstructure of coarse pearlite compressed 20 pct, then polished and etched. Here the lamellae form a step by bending at two

Jan 1, 1959

"The pumping of the underground water of the Butte mines is largely done from two central plants of the Anaconda Copper Mining Co. The mines of one part of the mining district are served by a modern and mechanically efficient underground plant at the High Ore mine, and the remaining part by a similar one at the Leonard mine. Properties not affiliated with the A. C. M. Co. have separate pumping plants, although in several instances that company handles the water of outside companies, under which arrangement costly single plants are dispensed with. An extensive system of underground crosscuts and drifts connects these mines to both the main pumping plants, so that either may receive the water from all the mines in case there should be a failure in the other to perform its designed service.Quintuple) vertical electric pumps, 7 inches by 12 inches each, of a capacity of 600 gals. per minute under a head of 1,203 feet, are installed at both the plants. Each pump is direct connected to two 150 h-p. motors using 2,300 volts, the motors being on top of the pumps.At the High Ore plant the power cable of 400,000 c. m. is placed in a nearby shaft, the cable at present being hung from the surface to the 2,200 level. From this cable feeders of 300,000 c. m. are laid in connecting crosscuts to the pumping station at the High Ore shaft.The Leonard motors use 440 volts. The practice of building the pumps with the motors on top requires stations with high roofs, but permits the operation of the pumps if they should be submerged by an unusual flow of water."

Jan 1, 1913

By R. D. Mollison, C. F. Fogarty

Sulfur is widely distributed in nature. It is present in the earth's crust, the ocean, the meteorites that come to us from cosmic space and in practically all animal and plant life. According to Clarke,9 the earth's crust contains 0.06 pct sulfur. Large quantities of free or combined sulfur are found in coal, natural gas and petroleum. Mineral waters contain sulfates and hydrogen sulfide. Sulfur is rather plentiful in the crust of the earth; however, only under special circumstances can it be produced profitably. Sulfur is one of the cheapest raw materials used by industry; and, therefore, the economic feasibility of a given deposit is strongly dictated by the law of supply and demand on local as well as world-wide levels. The forms which are commercially important are elemental sulfur or brimstone, and the sulfides such as pyrite (FeS2), pyrrhotite (FenSn+1), chalcocite (Cu2S), sphalerite (ZnS), and galena (PbS); the sulfates such as gypsum (CaSO4,2H2O), anhydrite (CaSO4), and kieserite (MgSO4,H2O). Elemental Sulfur Elemental sulfur is found in many localities, generally in solfataras and gypsum type deposits. The solfatara deposits are found commonly in the neighborhood of active or extinct volcanoes as in Italy, Japan and Chile, or fumaroles associated with mineral springs such as the Mammoth Hot Springs in Yellowstone Park. Here the sulfur is deposited in tufas or other porous host rocks. This type of sulfur deposit probably results from the oxidation of hydrogen sulfide or the reaction of hydrogen sulfide with sulfur dioxide. Most of the world's supply of elemental sulfur comes from the gypsum-type deposits. Here the mineral occurs as either crystalline or amorphous sulfur in sedimentary rocks in close association with gypsum and limestone. This association is characteristic and occurs in almost all the great gypsum beds of the world, although sulfur is not always present in quantities of economic importance. Various theories have been advanced to account for this association. Bischof5 suggested that the sulfur came from hydrogen sulfide which resulted from the reduction of calcium sulfate by carbon or methane in accordance with the following reactions: CaSO4 + 2C= CaS + 2CO2 CaS + C02+ H2O = CaCO3 + H2S CaSO4 + CH4= CaS + C02+ 2H20 2H2S + 02= 2H20 + 2S All of the sulfur-bearing domes on the Gulf Coast have calcium sulfate in great quantity in the cap. They all show the presence of hydrocarbons. The oxygen for the final reaction could have been supplied by circulating ground waters. The principal objection to this theory is that temperatures of 700° to 1000°C are needed to reduce the sulfate to sulfide with carbon compounds. The geologic evidence is that the temperature of the sulfur-bearing domes of Texas did not exceed 100°C. Proponents of the theory say that geologic time or a catalyst replaced temperature. According to another theory the sulfur in the salt domes is the result of bacterial action. Sulfate reducing bacteria have been detected in sulfur cores and in the formation water issuing from salt domes. It has, therefore, been suggested that these bacteria converted the sulfate to sulfide which subsequently was converted to elemental sulfur.

Jan 1, 1960

By J. J. Kramer, K. Foster

The orientation distribution of surface-energy -induced secondary recrystallized grains was determined. This work was conducted on thin sheets of a 3 pct Si-Fe alloy annealed under environmental conditions that furor grouth of grains with a (100) plane in the surface of the sheet. The texture was found to be extremely sharp and almost independent of sheet thickness. The distribution varied exponentially with the angular deviation from the {100} plane. It was possible to relate the distribution to the nu-cleation rate of the secondary rains as influenced by the surface-energy difference. THE role of surface energy in the secondary grain growth of cube-oriented grains (grains with a (100) plane in the plane of the sheet) in thin Si-Fe sheets has been previously discussed.1-4 In high-purity sheet material normal grain growth usually occurs until the grains have extended through the sheet. Further grain growth is inhibited by the thermal grooving of the boundaries at the sheet surface. However, additional growth of cube grains can occur by a secondary grain growth process under conditions where the (100) plane has a lower surface energy than other orientations. Apparently for these alloys, cusps exist in the polar plot5 of surface free energy with the lowest cusp energy occurring at the (100) orientations. This has been reported to be the result of preferential adsorption of sulfur on the (100) planes.6 As a result of this process, a distribution of orientations could arise from two possible mechanisms. First, when a cusp is present in the polar plot of surface free energy, there are orientations inside the cusp that have a lower surface energy than elsewhere on the polar plot. Also, at sufficiently high temperatures, flat surfaces whose orientations are inside or just outside the cusp (depending on its shape) can often thermally etch, yielding a microscopically stepped surface of even lower surface energy. As a result, grains oriented close to cube would also have a lower surface free energy, either because of the cusp shape or by thermal etching, and could possibly grow as secondary grains by the surface-energy phenomenon. One should thus observe a distribution in the surface orientation of the cube grains comprising the secondary structure. It is the purpose of this paper to investigate this orientation distribution experimentally and to discuss the factors involved in its formation. For this purpose, the surface orientations of a large number of secondary grains in various sheet thickness were determined by means of the Laue back-reflection X-ray technique. PROCEDURE A vacuum-melted 3 pct Si-Fe alloy containing a nominal impurity content of 0.005 wt pct was processed into strip. A single cold-rolling step of 90 pct reduction was used for each strip regardless of the final sheet thickness. Final strip thicknesses of 0.60, 0.30, 0.15, and 0.075 mm were used. Care was taken to insure that the final strip surface was smooth and flat. All strips of a given thickness were annealed together at 1200°C in dry hydrogen (dew point -70°C) to develop the desired secondary structure and to insure identical environmental annealing conditions. The annealing time was selected to develop a complete secondary structure in the thinner sheets but to permit the thicker sheets (0.60 mm) to have residual primary grains remaining. This was necessary to determine whether growth impingement could lead to one secondary grain consuming another at a greater angular deviation. For the X-ray determination of the surface orientation of the secondary grains, a special specimen holder was used. The camera and holder arrangement could be aligned by X-raying a grain in three positions rotated 180 deg to each other. Thus, with a small beam X-ray focus (1 mm), the surface orientation of any grain could be determined to within one-half a degree. The surface orientations of one hundred cube secondary grains were determined for each sheet thickness. The criteria of a secondary grain were its size relative to the sheet thickness and the number of sides of the grain observed in the sheet surface. (A primary recrystallized grain extending through a sheet will generally have six edges visible in the plane of the sheet, whereas a secondary grain will have many more when growing entirely into primary grains.) Grains were selected as randomly as possible by X-raying every secondary grain found along a line drawn on the strip. No attempt was made to determine the exact orientation of the planes of the surface, as many strips from randomly selected sheets were used. On1y the angular deviation of the surface plane from {100} was measured. In order to assess the volume distribution in the

Jan 1, 1965

By M. F. Smith

BELOW the nose of the bainitic C curves in isothermal transformation diagrams, the rate of the austenite-to-bainite transformation usually decreases with decreasing temperature. However, in some steels and iron-carbon alloys, there is a noticeable acceleration in the initial reaction rate at temperatures just above Ms. Such speeding-up of the bainitic transformation would be understandable at temperatures just below Ms because of the catalytic effect of the martensite formed,' but the reversal in isothermal kinetics just above Ms seems quite anomalous. This behavior was observed by Howard and Cohen' in a 1.35 pct C steel and, on the basis of metallo-graphic examination, it was attributed to the formation of a thin plate-like product not belonging in the bainitic sequence. More recently, schaaber2 found two-stage reactions occurring in the vicinity of Ms in a number of steels, and suggested that the first stage might be the isothermal formation of marten-site, preceding the isothermal formation of bainite in the second stage. A decrease in the bainitic incu-

Jan 1, 1960

By Horace Pops

Isothermal sections in the copper -rich region of the Cu-Si-Zn a1by system have been determined at 8473 760; 6003 and 482°C by means of microscopic examination with confirmatory X-ray diffraction work. The stability of the bee 0 phase decreases both with decreasing temperature and with increasing copper content. The silicon-n&apos;ch 0 phase decomposes upon quenching from high temperatures either by a martensitic or by a "massive" transformation, depending upon the solute content. A two-phase equilibrium is found to exist in the Cu-Si-Zn system between the hep < phase of the Cu-Si system and the bee ß phase of the Cu-Zn system. It is shown that the isothermal limits of the primary solid solution at 760; 6003 and 482°C are in part affected by the intermediate phases which follow them in the ternary system Possible electron-concentration and size effects upon phase boundaries are discussed. ALTHOUGH the mechanical and physical properties of silicon brasses have been measured in great detail, the factors which influence these properties are not well-understood, partly because the knowledge of the phase relationships in the Cu-Si-Zn system is limited. Gould and Ray1 studied the effects of silicon upon the hardness and structure of Cu-15 pet Zn and Cu-40 pet Zn alloys. They proposed an isothermal section at 800°C which was not based upon experimental data, since the binary phase diagrams had not been completely determined. Using Cu-Si-Zn alloys containing approximately 5 wt pet Si, vaders2 determined the boundary, at 750°C, between the copper-rich solid solution and an unidentified second phase. Masing and wallbaum3 examined a vertical section through the ternary diagram in the region between Cu-20 pet Zn and Cu-10 pet Si alloys, but they emphasized uncertainty about their data. Mima and Hasegawa4 studied the liquidus surface of Cu-Si-Zn alloys, phase transformations in high silicon-bearing (20 to 25 at. pet) alloys,5 and the phase relations in low silicon-bearing Cu-Si-Zn alloys.6 Their experiments were based upon thermal analyses and metallographic observations. The compositions of the phase boundaries were not determined with high precision, and the crystal structures of the phases were not reported. Because of uncertainties in the existing literature, it became of interest to determine more accurately the phase relations in copper-rich Cu-Si-Zn alloys. The crystal structures, stability, and phase boundaries of the primary solid solutions and several intermediate phases were determined, and the data are reported as partial isothermal sections.

Jan 1, 1964

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus become citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil. EXTENSIVE beds of a soft aluminiferous phosphate lie in the Bartow-Pembroke region of Florida. Although the extent of the deposit is unknown, it is thought that the equivalent of at least five million tons of material containing 25 pct P,Os exists on one large mine property alone, and soft phosphates similar in nature are known to occur elsewhere in the state. This aluminum phosphate, unlike fluorapatite, is rendered fairly soluble in neutral ammonium citrate solution merely by heating it at a temperature below 600 °C, a property made the basis of a process patent by the junior author.&apos; The possibility of producing an available form of phosphorus from what has hitherto been a worthless natural phosphate prompted the Bureau of Plant Industry, Soils, and Agricultural Engineering to make a brief study of the Pembroke phos- phate during the war years with a view towards determining the optimal temperature for heat treatment and the reactions involved in the process. The results of this study supplemented by data and information furnished by the junior author are presented in this paper. Description of Natural Phosphate: The phosphate with admixed quartz sand and siliceous matter occurs as a low-grade (8 to 9 pct P2O5) clay-like material that can be beneficiated cheaply by making a water separation of the very fine material from the sand, floating off the fine material, settling the suspension to a thick slurry, and finally de-watering the slurry by vacuum filtration followed by drying. The product dried at 100 °C contains about 16 pct water and 25 pct P2O5, about 1/12 of which is citrate soluble. Partial analyses of representative samples of the crude ore and corresponding concentrate are given in table I. The concentrate is light yellow in color and even after being dried at 100°C sticks very noticeably to laboratory grinding and screening equipment. Under the microscope the ground material is predominantly light brown crystalline aggregates with index of refraction near 1.61. The principal phosphate mineral constituent was identified as pseudo-wavellite with admixed phosphosiderite.2 Pseudo-

Jan 1, 1951

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus become citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil. EXTENSIVE beds of a soft aluminiferous phosphate lie in the Bartow-Pembroke region of Florida. Although the extent of the deposit is unknown, it is thought that the equivalent of at least five million tons of material containing 25 pct P,Os exists on one large mine property alone, and soft phosphates similar in nature are known to occur elsewhere in the state. This aluminum phosphate, unlike fluorapatite, is rendered fairly soluble in neutral ammonium citrate solution merely by heating it at a temperature below 600 °C, a property made the basis of a process patent by the junior author.&apos; The possibility of producing an available form of phosphorus from what has hitherto been a worthless natural phosphate prompted the Bureau of Plant Industry, Soils, and Agricultural Engineering to make a brief study of the Pembroke phos- phate during the war years with a view towards determining the optimal temperature for heat treatment and the reactions involved in the process. The results of this study supplemented by data and information furnished by the junior author are presented in this paper. Description of Natural Phosphate: The phosphate with admixed quartz sand and siliceous matter occurs as a low-grade (8 to 9 pct P2O5) clay-like material that can be beneficiated cheaply by making a water separation of the very fine material from the sand, floating off the fine material, settling the suspension to a thick slurry, and finally de-watering the slurry by vacuum filtration followed by drying. The product dried at 100 °C contains about 16 pct water and 25 pct P2O5, about 1/12 of which is citrate soluble. Partial analyses of representative samples of the crude ore and corresponding concentrate are given in table I. The concentrate is light yellow in color and even after being dried at 100°C sticks very noticeably to laboratory grinding and screening equipment. Under the microscope the ground material is predominantly light brown crystalline aggregates with index of refraction near 1.61. The principal phosphate mineral constituent was identified as pseudo-wavellite with admixed phosphosiderite.2 Pseudo-

Jan 1, 1951

Temperatures in the Open-hearth Furnace. By Robert B. Sosman. (Metals Tech. Aug. 1948, T.P. 2435) Steelmaking Direct Oxidation in the Basic Open Hearth Process. By E. R. Hughes and F. G. Norris. (Metals Tech., June 1948, T.P. 2380) With discussion Operation of Oxygen-enriched Open-hearth Furnaces. By J. S. Marsh. (Metals Tech., Aug. 1948, T. P. 2416) With discussion Role of Thermochemical Factors in Basic Open Hearth Production Rate. By T. E. Brower and B. M. Larsen. (Metals Tech., Oct. 1948, T.P. 2451) Structure, Segregation and Solidihcation of Semikilled Steel Ingots. By M. Tenenbaum. (Metals Tech., Sept. 1947, T.P. 2273) With discussion The Origin of Silicate Inclusions in Basic Electric-arc-furnace Steel of Higher Carbon Contents. By Axel Hultgren. (Metals Tech., Aug. 1948, T.P. 2418) A Method for Determining the Origin of Surface Defects in Rolled Steel Products. By C. L. Meyette and V. L. Elliott. (Metals Terh., June 1948, T.P. 2368) With discussion Gases in Steel The Sampling and Analysis of Steel for Hydrogen. By G. Derge, W. Peifer and J. H. Richards. (Metals Tech., June 1948, T.P. 2362) With discussion Apparatus for the Hot-extraction Analysis for Hydrogen in Steel. By C E. Sims and G. .I. Moore. (Metals Tech., June 1948, T.P. 2369) With discussion A Quantitative Experimental Investigation of the Hydrogen and Nitrogen Contents of Steel during Commercial Melting. By C. E. Sims, G. A. Moore and D. W. Williams. (Metals Tech., Feb. 1948, T.P. 2347) With discussion The Effect of Hydrogen on the Ductility of Cast Steels. By C. E. Sims, G. A. Moore and D. W. Williams. (Metals Tech., Sept. 1948, T.P. 2454) Sulphur in Ironmaking Kinetics of the Transfer of Sulphur across a Slag-metal Interface. By Lo-ching Chang and K. Goldman. (Metals Tech., June 1948, T.P. 2367) With discussion Some Correlations between Variables Affecting Sulphur in Blast Furnace Iron. By T. E. Brower and B. M. Larsen. (Metals Tech., Sept. 1948, T.P. 2465) Tracer Study of Sulphur in the Coke Oven. By S. E. Eaton, R. W. Hyde and 11. S. Old. (Metals Tech., Sept. 1948, T.P. 2453) Transformation of Austenite Anisothermal Formation of Bainite and Proeutectoid Constituents in Steels. By Leonard D. Jaffe. (Metals Tech., Dec. 1947, T.P. 2290) With discussion Austenite Transformation Above and Within the Martensite Range. By R. T. Howard, Jr. and M. Cohen. (Metals Tech., Oct. 1947, T.P. 2283) With discussion

Jan 1, 1949

By R. E. Hook, H. J. Garrett, A. M. Adair

X-ray diffraction and metallographic techniques were employed to examine the impurity phases occurring in as-swaged and recrystallized chromium produced fvom high-purity iodide chromium crystals. Chromium oxides are found to form in a consistent manner associated with the temperature of recrystallization. Microscopically observable second phase particles of Cr203 are observed to form intergranulurly beginning at 1300T. Beginning at 1500°C. Cr30, is formed intergvanulurly, atzd at 1600°C and above Cr30, is also formed in association with migrating grain boundaries. Geometrical traces formed by particles of this high temperature oxide uithin the grains rez)eal the histmy of grain boundary motion. X-ray evidence is presented which suggests the existence of a high temperature form of Cr203. Other impurity phases in addition to the oxides of chromium are also present. THE partitioning Of impurity elements between grain boundary aid lattice sires, either as solutes in solution or as second phases, may exercise an important influence on the mechanical behavior of metals and alloy systems. This partitioning of impurities could have a direct bearing on the iecrys-

Jan 1, 1963

By Sherman L. Pease

An inexpensive and relatively rapid method that can be used by field crews is described. Fluid movement is determined by releasing a tracer (dye) in the well at a predetermined level and, after an interval of time, sampling the well fluid at another level. The testing equipment consists of a combined crusher and sampler unit that is run into the well on a wire line. The rate of movement can be calculated from time-volume relationships. Description of Method It is often desirable to determine whether there is occurring any transfer of fluid from point to point in a shut-in well, and, if so, to measure the rate of movement. When it is desired to examine a large number of wells for possible "thief" sands, the time and expense will be considerable unless the method used is inexpensive and rapid. After experimentation with several possible solutions to the problem, the Production Department of the Shell Oil Co., Inc., developed the apparatus described herein, which has proved satisfactory. Routine operations with it can be carried out by field production crews with a minimum of technical supervision and with negligible investment in equipment. The method is based upon releasing a suitable tracer in the well fluid at a known level, and recovering a sample of well fluid at another level after a measured interval of time. Repetition of this process with different time intervals between release and sampling gives the necessary data. For purposes of illustration, the setup for measuring migration of fluid in an upward direction is described in the following paragraphs. The arrangement of equipment is shown diagrammatically on Fig. I. The elements of the combination unit are the tailpiece, the crushing device, the spacer and the sampling device. The lengths of the tailpiece and spacer are varied to place the crushing and sampling devices in the desired positions in relation to the sands being tested. The crushing device breaks the glass bottle containing the tracer when the tailpiece strikes the bottom of the well and the tension on the sand line is slackened. Because of the open construction of the crushing device, the tracer is quickly and completely disseminated in the well fluid. The sampling device is a suction bailer, which obtains a sample of the fluid surrounding the perforated nipple just before the unit is picked up off bottom. The sample is retained in the barrel by the ball valve for examination at the surface. Normally, on the first run into a well, the sample is obtained near the releasing point of the tracer, and thereafter samples are taken near the base of the upper sand if migration is indicated by the dilution or absence of the tracer in the initial sample. The length of the time interval between the releasing of the tracer and the sampling of the well fluid is varied for successive runs, attempting first to establish the rate within limits and then to define it more accurately by additional runs if necessary.

Jan 1, 1946

By Sherman L. Pease

An inexpensive and relatively rapid method that can be used by field crews is described. Fluid movement is determined by releasing a tracer (dye) in the well at a predetermined level and, after an interval of time, sampling the well fluid at another level. The testing equipment consists of a combined crusher and sampler unit that is run into the well on a wire line. The rate of movement can be calculated from time-volume relationships. Description of Method It is often desirable to determine whether there is occurring any transfer of fluid from point to point in a shut-in well, and, if so, to measure the rate of movement. When it is desired to examine a large number of wells for possible "thief" sands, the time and expense will be considerable unless the method used is inexpensive and rapid. After experimentation with several possible solutions to the problem, the Production Department of the Shell Oil Co., Inc., developed the apparatus described herein, which has proved satisfactory. Routine operations with it can be carried out by field production crews with a minimum of technical supervision and with negligible investment in equipment. The method is based upon releasing a suitable tracer in the well fluid at a known level, and recovering a sample of well fluid at another level after a measured interval of time. Repetition of this process with different time intervals between release and sampling gives the necessary data. For purposes of illustration, the setup for measuring migration of fluid in an upward direction is described in the following paragraphs. The arrangement of equipment is shown diagrammatically on Fig. I. The elements of the combination unit are the tailpiece, the crushing device, the spacer and the sampling device. The lengths of the tailpiece and spacer are varied to place the crushing and sampling devices in the desired positions in relation to the sands being tested. The crushing device breaks the glass bottle containing the tracer when the tailpiece strikes the bottom of the well and the tension on the sand line is slackened. Because of the open construction of the crushing device, the tracer is quickly and completely disseminated in the well fluid. The sampling device is a suction bailer, which obtains a sample of the fluid surrounding the perforated nipple just before the unit is picked up off bottom. The sample is retained in the barrel by the ball valve for examination at the surface. Normally, on the first run into a well, the sample is obtained near the releasing point of the tracer, and thereafter samples are taken near the base of the upper sand if migration is indicated by the dilution or absence of the tracer in the initial sample. The length of the time interval between the releasing of the tracer and the sampling of the well fluid is varied for successive runs, attempting first to establish the rate within limits and then to define it more accurately by additional runs if necessary.

Jan 1, 1946

By Ulrich H. Roesler

RECENTLY, C. Zener1 published a new thermo-dynamic treatment of the a/y transformation in iron alloys. His interpretation differs from the previous theories2-0 ainly through the separation of the free energy difference, Ga—G, into two additive

Jan 1, 1957