Search Documents

By J. L. Meijering

Oxidation hardening of cylindrical and spherical specimens first decreases with depth below the surface, but then increases again as the center is approached. This is in agreement with the view that this change in hardness is mainly determined by the change in velocity of the oxidation boundary, which affects the dispersion of the oxide. WHEN a thick slab of silver containing 0.3 pct Mg by weight is internally oxidized, the hardness measured on a cross section is found to decrease considerably with distance from the surface.&apos; This phenomenon has been attributed to the diminution of the velocity of the oxidation boundary. The smaller this velocity is, the more slowly the free-oxygen concentration rises towards the concentration in equilibrium with the oxygen gas. And a small 0 concentration favors dissociation and thus conglomeration of the oxide. For instance, the hardness decreases more rapidly during long annealings in nitrogen than in air.&apos; Measurements by Gregory and Smith3 on sections through internally oxidized Al-silver wire showed a smaller variation in hardness, probably because the wire diameter was only 0.9 mm. Wood4 found a drop in hardness with depth in internally oxidized Al-copper strip, and also—by electron microscopy—the concomitant increase in Al2O3 particle size. Under certain circumstances internal oxidation leads to formation of rather irregular inner oxide films in the midst of dispersed oxide. This special sort of conglomeration—discussed in Ref. 5—is also favored by greater depth below the surface.3,5 In this paper hardness measurements in large diameter cylindrical and spherical specimens are described. Here the oxidation velocity* goes through ness initially decreases with depth but increases again towards the center. Normally, the diffusion coefficient D1 of oxygen is very large compared to D2, that of the dissolved metal. If, furthermore, the atomic fraction c2 of the latter is much larger than the O-solubility cl- but c2D2 << c1D1- the velocities in question are easily calculated2 to be: for the cylinder and for the sphere. Here p is the radial coordinate of the oxidation boundary and R the specimen radius, which in dilute silver alloys is constant, as no external oxidation occurs. These equations have been derived for a divalent solute; for nondivalent solutes c2 has to be multiplied by half the valency. The equations are not valid near the center. For which can be considered as a standard case,2 the Eqs [I] and [2] begin to yield U-values which are appreciably too high for p/R = 0.05 and 0.15, respectively. But at the v-minima they are still very good approximations. These minima lie at p = emlR= 0.37R in the cylinder and p = 1/2 R in the sphere. Other factors besides the velocity v will also influence the hardness. The oxide concentration cox is constant in a flat strip, apart from a narrow region in the middle,2 but in cylindrical and spherical specimens cox decreases steadily with depth. When C1 << c2 and c1D1 >> c2D2 one can calculate

Jan 1, 1961

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler&apos;s saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler&apos;s saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By W. A. Backofen, F. de Kazinczy

FRACTURING under conditions of particular interest is identified with the junction of curves relating tensile yield and fracture stresses to test temperature; the intersection point gives the lowest stress, for brittle fracture (at the ductility transition temperature). An expression for is found in Cottrell&apos;s brittle-fracture analysis, Eq. [15],1 while measurements of this stress and temperature have been reported for a low-carbon steel heat treated to differ-

Jan 1, 1962

Illustrated guidebooks treating in a popular descriptive way of the geology and other features of the Western United States have been issued by the U. S. Geological Survey. They will be of much interest to mem¬bers in connection with the Arizona Meeting of the Institute and espe¬cially the guidebook of the Santa Fe Route, with side trips to the Grand Canyon, containing as it does relief maps, topographical and geological maps, covering the entire route of the railroad, illustrations from photo¬graphs and other interesting descriptions of this great country. The method of treatment is adapted to the lay-reader, although it includes much valuable and interesting technical information concerning the geographical and other features. The books are well indexed. These volumes sell for 50 c. each and may be obtained from the Superintendent of Documents, Washington, D. C. These guidebooks originally sold for $1 each, but the reprint edition has been reduced to 50 c. A list of the different guidebooks follows: Bulletin 611. Guidebook of the Western United States, Part A, The Northern Pacific Route, with a Side Trip to Yellowstone Park, by M. R. Campbell, and others. 1915. 212 pages, 27 route maps, 27 plates, 39 text figures.

Jan 6, 1916

By R. J. P. Lyon

It is usually assumed1,2 that ore deposition is relatively slow, taking place over tens of thousands of years. Yet many syntheses and phase changes can be completed in the laboratory in a matter of hours, under essentially the same pressure and temperature conditions to be expected in nature. Much has been written about geothermometry, and Ingerson&apos;s recent summary2 an hardly be surpassed. Rather than review the whole field, this article will deal specifically with diffusion rates in solid solutions* of the sulfide minerals. In the study and application of temperature-indicating phenomena to problems of ore genesis, the time factor has often been neglected. In the particular case of sulfide systems, the speed of unmixing and diffusion of the constituent phases in the solid solutions has seldom been considered when laboratory data are applied to the genesis of natural sulfide ores. Chalcopyrite and Bornite Intergrowths: Chal-copyrite and bornite are copper iron sulfides often found in association. In many ores the individual grains appear to have mutual boundaries, but bladed intergrowths are quite common. Early workers in the field, " deduced that while these patterns could have been formed by replacement, they could be experimentally reproduced from the unmixing of solid solutions of the two previously homogenized at 475°C. Much of the ore from Roan Antelope mine in the Rhodesian Copper Belt exhibits these bornite-chalcopyrite intergrowths, from which it has been deduced that the ores could have been subjected to a minimum temperature of 475°C. In several recent interpretations,&apos; this temperature rise has been considered to result from a regional metamorphism of an original syngenetic copper-bearing sediment. The same temperature rise to 475 °C was suggested from similar intergrowths in the sulfide- • The general subject of solid solution in structurally similar minerels is treated in many texts&apos;. :&apos; &apos; and will not be further elucidated. bearing ore from the Happy Jack uranium mine8 on tile Colorado Plateau, although this temperature had a different origin. In 1931 SchwartzV etermined that 475°C represented the unmixing temperature of his bornite-chalcopyrite solid solutions but, more important, that the characteristic intergrowths of bornite and chalcopyrite could be preserved only if the solid solution were chilled quickly to room temperature. This significant corollary has been almost completely neglected by both Davis and Miller.7,8 By suitably decreasing the cooling rate, Schwartz found that the original pattern of the intergrowth was reformed (Fig. 1). The cooling rate was critical. In cooling from 475°C to room temperature in

Jan 1, 1960

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

Hydrogen forms a beta-stabilized system with titanium, with a beta eutectoid at about 300°C and 44 atomic pct H2. &apos;The solid solubility of hydrogen in alpha decreases from about 8 to about 0.1 atomic pct from 300°C to room temperature. Hydrogen has little effect on tensile properties, but decreases notch-bar toughness to a large degree. This latter effect appears to be the result of increased notch sensitivity. PRIOR to this investigation, only a small amount of information was available on the effect of hydrogen on the mechanical properties of titanium. The effects of the other interstitially soluble elements, carbon, oxygen, and nitrogen, had received detailed study. Jaffee and Campbell1 indicated that hydrogen up to 1 atomic pct did not affect tensile properties deleteriously. Pitler&apos; indicated that 1 atomic pct H, in titanium reduced the impact strength appreciably, but his alloys contained appreciable amounts of oxygen, and it was difficult to attribute the embrittlement entirely to hydrogen. The high temperature portion of the equilibrium diagram for the Ti-H system was established by McQuillan," and his data generally corresponded with the results of Kirschfeld and Sieverts," Gibb and Kruschwitz," Bevington, Martin, and Mathews," and other investigators. The lower concentration limit of the hydride phase varied considerably among investigators, and Gibb and Kruschwitz9 ad shown that small amounts of contaminants in either titanium or hydrogen caused considerable variation in this lower limit. In view of this pronounced effect of contaminants, the extrapolated value of McQuillan&apos;s, about 48 atomic pct at the 325°C eutectoid, appeared the most reasonable. McQuillan&apos;s lowest experimental value was 54 atomic pct at a temperature of 450 °C. The density of titanium had been shown to decrease with increasing hydrogen content, but discrepancies were noted among the various investigations. The best values indicated that the density was decreased from 4.56 grams per cc at 0.27 atomic pctl to 3.84 grams per cc at 61.3 atomic pct? This investigation was conducted to determine the effects of hydrogen on a titanium, both in high purity and commercially pure metals, and on high purity a titanium alloys. Material and Fabrication The literature indicated that impurities in either the hydrogen or the titanium must be kept to a minimum. For this reason, the initial studies were made with high purity iodide-refined titanium. The vendor&apos;s analysis of the iodide titanium and the hydrogen content of the as-fabricated Y4 in. diameter rods are shown in Table I. Two 1 lb ingots were prepared by arc melting under argon in a water-cooled crucible, using a water,cooled tungsten electrode. This equipment has been described.&apos; As-cast Brine11 hardness numbers of 88 and 58 for these ingots were low enough to insure that the high purity of the metal was maintained during arc melting. The ingots were hot forged to % in. diameter rods at 800°C, cleaned by grit blasting, and then cold swaged to Yz in. diameter rods. The rod was then air annealed at 725 "C, ground to remove scale, and cold swaged to Y4 in. diameter (75 pct reduction in area). The material was then annealed for 1 hr in argon at 800°C to develop an equiaxed a grain size of about 0.05 mm. Micro tensile specimens and microimpact specimens were machined from this rod prior to treatment in the Sieverts-type absorption apparatus. Two lots of commercially pure RC-55 titanium were also used in this investigation to determine the effects of hydrogen and the normal impurities on mechanical properties. The commercially pure RC-55 alloy was obtained in the form of % in. diameter rod. The analysis of this material is also given in Table I. The % in. diameter rods were hot swaged

Jan 1, 1955

By J. E. Hilliard

Isobaric sections of the eutectoid region of the iron-carbon phase diagram have been exgerimentally determined at 35, 50, and 65 kb. The phase boundaries were located by metallographic analysis of specimens quenched after equilibriatwn at known temperatures and pressures. With increasing pres -sure a pronounced decrease in the solubility of FesC in austenite was observed together with a depression of the eutectoid temperature. These two effects resulted in a shift of the eutectoid composition toward a lower carbon content; at 65 kb the eutectoid was at less than 0.2 wt pct C. These results are in qualitative agreement with thermodynamic calculations. It has also been shown by calculations that Fe3C in contact with saturated austenite will be stable with respect to both graphite and diamond formation at all pressures above -3.5 kb. 1 HE investigation described in this article was part of a more general study of the effect of high pressure on transformations in Fe-C alloys. Thermodynamic calculations and exploratory runs made in 1959 at the start of the program indicated an appreciable change with pressure in the phase equilibria of Fe-C alloys. However, the calculations were not considered reliable enought to provide the quantitative information required for the interpretation of the effect of pressure on the kinetics of transformations. An experimental investigation was therefore made to determine a series of isobaric sections of the eutectoid region of the phase diagram at pressures up to 65 kb. EXPERIMENTAL PROCEDURE Materials. Seven alloys with analyzed carbon contents of 0.10, 0.20, 0.38, 0.60, 0.77, 0.93, and 1.20 wt pct C were prepared from Ferrovac" iron and high-purity graphite induction melted in magnesia crucibles under argon. The ingots were hot worked and swaged down to 0.19-in.-diam rod which was then centerless ground to a final diameter of 0.125 in. Samples for chemical and spectrographic analyses were taken from each end of the rods. The prin- cipal impurities were found to be Ni, Al, Co, and Si which were present in amounts up to 0.03, 0.02, 0.01, and 0.01 wt pct, respectively. Specimens were prepared by slicing the ground rods into pills 0.06-in. thick which were silver plated to reduce decarburization during the equilibration. Silver was chosen for this purpose because of its very low solubility for carbon and its mutual immisicibility with iron. High-Pressure Apparatus. The high-pressure runs were carried out in the "Belt" apparatus.&apos; As shown in Fig. 1, this consisted of a cylindrical cell compressed between two Carboloy punches loaded by a uniaxle press. Radial support to the cell was given by the "belt" which was a Carboloy die heavily prestressed by a series of steel binding rings. Laminated gaskets of lava and metal separated the punches from the inner surface of the "belt". A cross-section of the high-pressure cell is shown in Fig. 2. Two specimen pills were located inside a resistance heater of 0.20-in.-diam Nichrome tubing. The ends of the tube were sealed with alumina and lava pills tamped in place after the

Jan 1, 1963

By Richard W. Smith

Kyanite, long known to occur in Georgia, did not excite coimmercial interest until about 1930. Investigation1 revealed two main types of deposits: (1) separate kyanite crystals embedded in mica schist; and (2) crystal aggregates of kyanite associated with quartz in small and very irregular veins. The second kind at first sight appeared to be the best source of supply. Large boulders or dornicks of kyanite with more or less quartz were found on the surface at many places throughout the Piedmont and Highland sections of the state, but prospecting failed to disclose a sizable vein. These dornicks seem to be a surface accumulation from small veins or lens-shaped masses not more than one or two feet thick, and with a horizontal extent of not more than a few feet. &apos;rile larger surface accumulation of kyanite dornicks, where not too badly stained by iron oxide, may prove to be marketable, but it is extremely doubtful whether a vein large enough to mine will ever be found. In 1932 deposits of the kyanite-mica schist were known to occur in two places northwest of Clarkesville, in Habersharn County. In 1934, at the request of and in cooperation with the Georgia Geological Survey, the United States Geological Survey made a thorough investigation2 of the deposits and found that the two known areas of kyanite-mica schist in Habershain County were but a part of an unsymmetrical, U-shaped belt (Fig. 1) with a western limb extending into Rabun County and somewhat longer than the eastern limb. The total length of the belt is about 30 miles. The width of outcrop ranges from 100 ft. to 1/4 mile or more. Deposits of kyanite-mica schist of very doubtful commercial importance were found in several other counties. Only the deposits of this kyanitc-mica schist belt in Habersham and Rabun counties will bc discussed in this paper. Geology The kyanite-mica schist of Habersham and Rabun counties occurs near the northern cdge of the Piedmont Upland in metamorphic rocks of pre-Cambrian age3. These rocks probably were deposited as sedimentary

Jan 1, 1938

By Richard W. Smith

Kyanite, long known to occur in Georgia, did not excite coimmercial interest until about 1930. Investigation1 revealed two main types of deposits: (1) separate kyanite crystals embedded in mica schist; and (2) crystal aggregates of kyanite associated with quartz in small and very irregular veins. The second kind at first sight appeared to be the best source of supply. Large boulders or dornicks of kyanite with more or less quartz were found on the surface at many places throughout the Piedmont and Highland sections of the state, but prospecting failed to disclose a sizable vein. These dornicks seem to be a surface accumulation from small veins or lens-shaped masses not more than one or two feet thick, and with a horizontal extent of not more than a few feet. &apos;rile larger surface accumulation of kyanite dornicks, where not too badly stained by iron oxide, may prove to be marketable, but it is extremely doubtful whether a vein large enough to mine will ever be found. In 1932 deposits of the kyanite-mica schist were known to occur in two places northwest of Clarkesville, in Habersharn County. In 1934, at the request of and in cooperation with the Georgia Geological Survey, the United States Geological Survey made a thorough investigation2 of the deposits and found that the two known areas of kyanite-mica schist in Habershain County were but a part of an unsymmetrical, U-shaped belt (Fig. 1) with a western limb extending into Rabun County and somewhat longer than the eastern limb. The total length of the belt is about 30 miles. The width of outcrop ranges from 100 ft. to 1/4 mile or more. Deposits of kyanite-mica schist of very doubtful commercial importance were found in several other counties. Only the deposits of this kyanitc-mica schist belt in Habersham and Rabun counties will bc discussed in this paper. Geology The kyanite-mica schist of Habersham and Rabun counties occurs near the northern cdge of the Piedmont Upland in metamorphic rocks of pre-Cambrian age3. These rocks probably were deposited as sedimentary

Jan 1, 1938

By John W. Cloud

The delivery of blows upon roadway structures by the locomotive engine at high speed, althongh long recognized, has, perhaps, not been as generally understood in severity, relation to speed, and cause as is desirable in matters of such importance. Some points of explanation, with illustrative disgrams, are, therefore, submitted to your attention, preparatory to a note 011 " Steel for Bridges," also submitted. In order that a locomotive may run at high rates of speed with-

Jan 1, 1881

Established as a Division March 13, 1935 R H Feierabend, Chairman T E Gillingham, Jr, Northeast Vice-Chairman W A Riggs, Southeast Vice-Chairman C F Clausen, Mid-Continent Vice-Chairman R H Wilpolt, Rocky Mountain Vice-Chairman J K Brooke, Pacific Southwest Vice-Chairman Leslie C Richards, Pacific Northwest Chairman V A Haw, Canadian Vice-Chairman J S Holland, Sec&apos;y -Treas National Lead Company Mining Department 111 Broadway New York 6, New York

Jan 1, 1960

Executive SIDNEY J. JENNINGS, Chairman GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership KARL EILERS, Chairman LEWIS W. FRANCIS J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON, Chairman CHARLES-F. R AND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS8 GEORGE C. STONE2 J. H. JANE WAY&apos; BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 4, 1918

By John W. Cloud

THE delivery of blows upon roadway structures by the locomotive engine at high speed, although long recognized, has, perhaps, not been a generally understood in severity, relation to speed, and cause as is desirable in matters of such importance. Some points of explanation, with illustrative diagrams, are, therefore, submitted to your attention, preparatory to a note on "Steel for Bridges," also submitted. In order that a locomotive may run at high rates of speed with-

Jan 1, 1881

[Admissions: H. J. Gruy, Chairman Kenneth W. Robbins W. Frank West Aurel E. Smith R. F. Madera Tom G. Calhoun Kenneth F. Anderson B. M. Goltlieb Advertising: Clark R. Edgecomb, Chairman Bernard F. Klein. Henry N. Lyle R. E. Howard H. M. Krause, Jr. Education: R. L. Whiting, Chairman John M. -Campbell E. T. Guerrero Don D. Little J. C. McCarthy Frank G. Miller Douglas Ragland H. C. Slider R. L. Slobod]

Jan 1, 1961

[New York Holds monthly meetings, except June, July and August. J. E. SPURR, Chairman A D. BROKAW, Vice-chairman SIDNEY ROLLE, Vice-chairman M. H. MERRISS, Secretary-treasurer, Nichols Copper Co., 25 Broad St., New York M. F. CHASE KARL HOFFMAN Boston Meets first Monday of each winter month. C. R. HAYWARD. Chairman E. C. GEITHER, Vice-chairman D. H. MCLAUGHLIN, Secretary-treasurer Rotch Bldg., Harvard Univ. Cambridge. Mass. GEO. H. GILMAN GEO. A. PACKARD]

Jan 1, 1928

Executive SIDNEY J. JENNINGS, Chairman GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership. EARL EILERS, Chairman. LEWIS W. FRANCIS J. E. JOHNSON. JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON, Chairman CHARLES F. BAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS3 GEORGE C. STONE2 J. H. JANE WAY4 BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 8, 1918

E O&apos;C Acker &apos;86 Jinzoc Adachl &apos;88 Frederic R Abbe &apos;97 T H Aldrich &apos;96 Truman H Aldrich &apos;78 Walter H Aldridge &apos;89 Anson W Allen &apos;87 John H Allen &apos;84 Thomas Andrews &apos;94 William R Appleby &apos;90 R M Atwater, Jr &apos;97 Lawrence Austin &apos;82 S Ayres &apos;73 H Foster Bain &apos;97 David Baker &apos;86 John Henry Banks &apos;83 Henry C Banon &apos;90 Thomas J Barbour &apos;97 Alonzo F Bardwell &apos;89

Jan 1, 1952

By Earl S. Greiner, Eric R. Jette

The constitution of the iron-silicon alloys containing from 14 to 33.4 weight per cent silicon has been studied by a number of investigators, whose results have been reviewed in a monograph published by the Engineering Foundation1. In these previous researches, the solubility of silicon in iron was determined by thermal, microscopic or magnetic methods and the compound Fe3Si2 was reported to be stable at temperatures from 0 to approximately 1030&apos; C. This paper describes the results of an X-ray investigation of the solubility of silicon in iron and gives data which prove that the Fe3Si2 phase is unstable below 825" C. In order to obtain the present results on the solubility of silicon in iron, the authors have utilized the lattice constants of the alpha-phase iron-silicon alloys given in a previous publication2, and also some additional data which will subsequently be described. Materials and Methods The alloys used in this investigation are listed in Table 1. They were prepared in 30 or 50-gram ingots by melting specially purified silicon and electrolytic or carbonyl iron in alundum crucibles under a pressure of less than 1 mm. of mercury. The purity of the silicon, electrolytic and carbonyl irons has been given by the authors in previous publications2, 5. The ingots were homogenized in vacuo at approximately 1000" C. for at least 96 hr. and then slowly cooled. The homogenized specimens were ground to powder in a hardened steel mortar. This powder was passed through a 150 or 200-mesh screen and sealed in evacuated quartz, Jena or Pyrex glass tubes and heat-treated as noted in the various tables. Specimens 23A, 24B, 33 and 35 and the specimens heated for one month at 700" C. were quenched by quickly removing the tubes from a horizontal tubular furnace and dropping them into water. The other specimens were quenched by means of a drop-quenching device, which has been described previously3.

Jan 1, 1937

By N. P. Pinto

Compacting below the recrystallization temperature was studied. Ideal density was attained at 550° to 600°C using 25 tsi. Compacts have strength and hardness higher than cold worked beryllium. The recrystallization temperature of this highly stressed metal is that of cast, cold worked beryllium and appears independent of pressing temperature. THE process metallurgy of beryllium is beset by many difficulties that hinder the production of sound beryllium shapes of controlled properties. Most of these obstacles are traceable directly to the low density, low ductility, and high affinity for oxygen of the metal. Castings are susceptible to cracking and porosity, and controlled grain size is not easily attained, yet is critical to further working. Any process must carefully avoid oxygen pickup. Conventional metallurgical processes, including melting, casting, forging, rolling, and extruding have been treated previously,&apos;" as have the conventional powder metallurgical methods.&apos; More recently, a method has been advanced for producing powder compacts of high density by hot pressing at 1000" to 1100°C, using pressures of 0.25 to 0.5 tons per sq in. (tsi).3 Here, Seybolt and coworkers attained theoretical density of 1.85 grams per cc using pres-sure-temperature combinations of 500 psi-1100°C, 750 psi-1075"C, and higher. The warm pressing of beryllium is a practical method for producing bars of controlled properties and appears to have certain advantages, particularly when high strength and hardness are required. Other investigators have studied the hot pressing of various pure metals, such as copper,"-" gold," iron,10-11 and aluminum." Their results indicate that ideal densities may be attained by compacting at temperatures less than 50 pct of the absolute melt-

Jan 1, 1955