Search Documents

By L. R. Jackson, W. T. Lankford, K. F. Smith

ComMercial steel sheet is prepared by a combination of hot and cold rolling and annealing. This treatment usually results in more or less pronounced anisotropy. The anisotropy may manifest itself both as preferred orientation and in the manner in which impurities, segregations, and the like, are aligned in the sheet. The type of preferred orientation and the organization of impurities or segregations may affect the elastic moduli, the yield strength, the tensile strength, and almost always the amount of ductility in different directions. In any case, the most important directions concerned in the anisotropy are along the rolling direction, along the width direction, and along the thickness direction. Considerable data exist on the anisot-ropy of sheet steel as demonstrated by conventional tensile tests; however, few attempts have been made to measure the constants of plastic anisotropy and use them to describe the flow of anisotropic sheet under combined stresses. In this paper, evidence is presented indicating that plastic flow in anisotropic sheet can be described by the shear-strain energy flow theory provided that the anisotropy is properly taken into account. Materials Used in the Investigation Table I lists the sheet materials used in this investigation and describes the condition in which materials were tested. Direction, of Tests and Test Methods Two types of tests were run—tensile tests and hydraulic-bulge tests. Characteristic parameters of anisotropy were determined from the tension tests by methods which will be described later. In all cases, the tensile test pieces were cut from the same quarter line and adjacent to the bulge test pieces in the sheet in order to minimize

Jan 1, 1949

By H. L. Armstrong

SOLID-STATE diffusion is an important technique in certain aspects of metallurgy, and especially the metallurgy of semi-conductors and semi-conductor devices. If the diffusion is carried out under constant conditions for a time, t, the concentration, C, of the diffusant at a depth, x, below the surface from which the diffusion is carried out is given by an expression of the form. C = Cof(x,Dt) [I] Co being a constant, and D the diffusion constant of the diffusant in the material and at the temperature

Jan 1, 1959

By W. J. Babyak, J. M. Sheehan, H. W. Paxton

THE- solubility of hydrogen and deuterium in solid niobium up to I-atm pressure has been established bv a number of workers.1-5 X-ray examination at room temperature of specimens reacted in hydrogen at high temperatures from 300° to 1000°C shows the presence of two phases—a bcc phase (a) based on the niobium lattice and with an u0, increasing from 3.30A for Nb to 3.32Afor NbHo.L, and an orthorhombic phase6n = 4.84A, h=4.90A, c =

Jan 1, 1960

By Otto H. Henry, J. J. Cordiano

Though powder metallurgy is one of the oldest of metallurgical processes, it is in its infancy as a branch of the modern field of metallurgy. As early as 3000 B.C., the ancients produced implements and weapons of iron by reducing iron ore in a charcoal fire and forging the resultant sponge while still hot into the desired shape. Melting and casting soon superseded the powder metallurgy practice, and it was not until the turn of the twentieth century that powder metallurgy was applied to the commercial manufacture of tungsten lamp filaments. From this beginning, the use of the powder metallurgy process spread" to the manufacture of porous oil-impregnated bearings, cemented carbide tools, contact points, diamond grinding wheels, clutch facings, starter brushes, resin-bonded radio cores, magnets, metallic filters, and other parts. More recently, and particularly during the present war, there has been a definite trend toward the manufacture of machine parts by this process in competition with the more conventional fabricating methods. Notwithstanding these many developments, scientific progress has been slow. While many articles on powder metallurgy have appeared in the press and various publications, there have been too few contributions to our technical societies, with the result that there is a dearth of the type of information necessary for the full development of this science. It is of primary importance that the results of research and development be freely disseminated if powder metallurgy is to realize its fullest potentialities. Purpose of Investigation Excluding the refractory metal field, all commercial powder metallurgical products made by a cold compressing and sintering operation contain voids. These voids can be substantially eliminated by subsequent severe working and heat-treatment, but ' such practice has not proved economical in most applications. By applying heat during the compressing operation, plastic deformation of the powder particles is substantially increased, and the resultant compact or briquette is practically free of voids. However, hot-pressing has many attendant problems, which at present preclude its use in the manufacture of precision parts. The more important of these are to devise: 1. A die steel capable of withstanding high pressures at elevated temperatures. 2. A high-temperature lubricant capable of preventing excessive die wear and welding of the compact to the die walls. 3. A method of retaining a neutral or reducing atmosphere in the compacting zone of the die assembly. 4. A means of ejecting the hot-pressed specimen into a neutral atmosphere until reasonably cold.

Jan 1, 1946

By Otto H. Henry, J. J. Cordiano

Though powder metallurgy is one of the oldest of metallurgical processes, it is in its infancy as a branch of the modern field of metallurgy. As early as 3000 B.C., the ancients produced implements and weapons of iron by reducing iron ore in a charcoal fire and forging the resultant sponge while still hot into the desired shape. Melting and casting soon superseded the powder metallurgy practice, and it was not until the turn of the twentieth century that powder metallurgy was applied to the commercial manufacture of tungsten lamp filaments. From this beginning, the use of the powder metallurgy process spread" to the manufacture of porous oil-impregnated bearings, cemented carbide tools, contact points, diamond grinding wheels, clutch facings, starter brushes, resin-bonded radio cores, magnets, metallic filters, and other parts. More recently, and particularly during the present war, there has been a definite trend toward the manufacture of machine parts by this process in competition with the more conventional fabricating methods. Notwithstanding these many developments, scientific progress has been slow. While many articles on powder metallurgy have appeared in the press and various publications, there have been too few contributions to our technical societies, with the result that there is a dearth of the type of information necessary for the full development of this science. It is of primary importance that the results of research and development be freely disseminated if powder metallurgy is to realize its fullest potentialities. Purpose of Investigation Excluding the refractory metal field, all commercial powder metallurgical products made by a cold compressing and sintering operation contain voids. These voids can be substantially eliminated by subsequent severe working and heat-treatment, but ' such practice has not proved economical in most applications. By applying heat during the compressing operation, plastic deformation of the powder particles is substantially increased, and the resultant compact or briquette is practically free of voids. However, hot-pressing has many attendant problems, which at present preclude its use in the manufacture of precision parts. The more important of these are to devise: 1. A die steel capable of withstanding high pressures at elevated temperatures. 2. A high-temperature lubricant capable of preventing excessive die wear and welding of the compact to the die walls. 3. A method of retaining a neutral or reducing atmosphere in the compacting zone of the die assembly. 4. A means of ejecting the hot-pressed specimen into a neutral atmosphere until reasonably cold.

Jan 1, 1946

1944 WALTER HULL ALDRIDGE New York, N Y 1946 PETER M ANDERSON Johannesburg, South Africa 1946 CHARLES CAMSELL Ottawa, Ont, Canada 1946 CHARLES AUGUSTUS CARLOW Fife, Scotland 1949 ERLE V DAVELER New York, N. Y 1951 EVERETTE LEE DEGOLYER Dallas, Texas 1946 CECIL H DESCH London, England 1946 WILLIAM FRASER London, England 1917 HERBERT HOOVER New York, N. Y 1941 DANIEL COWAN JACKLING San Francisco, Calif. 1950 ZAY JEFFRIES Pittsfield, Mass 1939 HENRY KRUMB New York, N Y 1942 ESSINGTON LEWIS Melbourne, Vic, Australia 1944 WALTER C. MENDENHALL Washington, D. C 1942 PAUL DYER MERICA New York, N Y 1938 A M PORTEVIN Paris, France 1934 T A RICKARD Victoria, B C, Canada 1946 JOHN R SUMAN Houston, Texas 1946 WONG WEN-HAO Chungking, China

Jan 1, 1952

Without having asked for it, the writer has apparently been drawn into the discussion regarding relative hoisting capacities which was started by Woodward Iron, egged on by Joe Haller of Cleveland-Cliffs [Mining Engineering, August p. 642] and Axel Kjelgaard [November p. 919], who took exception to Mr. Haller's remarks of tonnage hoisted and avers that they do better in Sweden. It does not appear to the writer that Mr. Haller was inclined to refer to the tonnage hoisted at Cleveland-Cliffs in a manner to imply that they claimed any hoisting record, but rather as a statement that they had hoisted a certain amount of ore during the year 1950. Mr. Haller has been in the mining game long enough to appreciate what Mr. Kjelgaard did not apparently take into consideration, that length of haul, shifts hoisted, nature of ore, method of loading and the many other factors which influence the hoisting cycle make a comparison of tonnages hoisted of two given mines almost an impossibility. Mr. Cheyette sent you .a copy of his letter to Bob Manegold relative to the capacities of the Orient #2 mine. There are several mines around the Country which constantly set up records about which little or nothing at all is ever heard. We cite the Snow Hill Coal Co. mine at Terre Haute, Ind., which has an automatic Nordberg hoist and which hoists 12 tons per trip or 700 tons per hr from 700 ft. This is a counter-weighted installation and a complete cycle is made every 62 seconds or 58 trips per hr. Another mine, The Potash Company of America mine at Carlsbad, N. Mex., has a Nordberg automatic hoist, hoisting eight tons per trip from 1150 ft on a one minute cycle. The materials hoisted in these two mines are ideal for automatic hoisting-they are free flowing so that no hang up is anticipated and hoisting is continuous. Multiplying out the above figures you will find that it is possible to hoist 11,000 tons in two shifts at Snow Hill or over 3 million tons in 300 days per year and over 2 million tons at Potash. Other mines have records which can be pointed to with pride. When a record for one year is established, it doesn't stand too long as here in America the ambition of all the men connected with the operation forces them on to larger tonnages. T. C. WIEDENHOEFER MANAGER MINE HOIST DEPARTMENT NORDBERG MANUFACTNRING CO. MILWAUKEE, WIS.

Jan 1, 1952

By J. R. Low, M. B. Reynolds, L. O. Sullivan

The effect of neutron bombardment upon the stability of type 347 austenitic stainless steel has been investigated by a magnetic technique. The relation of the ferrite content of a stainless steel to its magnetic properties is given, and an apparatus suitable for the measurement of the ferromagnetic saturation induction of small specimens is described. Results of measurements on irradiated specimens are tabulated. Exposure to a neutron flux was found to cause a slight increase in the ferrite content of type 347 stainless steel, the change increasing with increasing length of exposure and with increasing initial ferrite content. The similarity of the effect of irradiation to the effect of annealing is pointed out. Possible effect of irradiation upon density of austenitic stainless steel is discussed. COMMERCIAL austenitic stainless steels are alloys of iron, chromium, and nickel, plus small quantities of other elements. Although these alloys are normally used in the austenitic condition, this state is thermodynamically metastable at ordinary temperatures and transformation to a more stable state takes place under favorable conditions. In the austenitic state, these stainless steels have the face-centered-cubic crystal structure characteristic of y iron, but the stable state at room temperature is a mixture of austenite and body-centered-cubic ferrite. The transformation from the pure austenitic condition may be brought about by cold working the alloy at a temperature below that at which the aus- tenite becomes thermodynamically unstable (about 400°C), the completeness of transformation increasing with increasing severity of cold work and decreasing temperature. The behavior of the austenitic stainless steels under ordinary conditions of use is rather well known. However, use of these alloys in a nuclear reactor introduces a new variable: the effect of neutron bombardment upon the transformation from the austenitic to the ferritic state. It was with this in mind that a study of the radiation stability of austenitic type 347 stainless steel was undertaken. Magnetic Technique for Ferrite Determination Commercial austenitic stainless steels such as type 347 undergo little transformation under normal conditions of fabrication and use. In view of this fact, it seemed likely that neutron irradiation would change the ferrite content of the alloy but little. The method chosen for measurement of the effect of neutron irradiation was thus limited to one which would be quite sensitive to small changes in the ferrite content of the alloy. Of the properties of the stainless steel which can be measured, the magnetic characteristics are most sensitive to the quantity of ferrite present.

Jan 1, 1956

By F. V. Lenel

R. P. Seelig.*—Dr. Lenel is to be congratulated on his presentation of a particularly interesting paper describing the use of the powder metallurgy process for the production of magnetic pole pieces. The only thing that might be added is that we have been successful in producing pole . pieces with a narrow hysteresis curve by the use of considerably lower sintering temperatures than the ones used by Dr. Lenel. It is quite possible that this use of lowe- temperatures has considerably widened the field of commercial application for pole pieces made from metal powders. Development work is currently being done on an a.c. application of a sintered iron part. However, I am in full agreement with Dr. Lenel that if eddy currents are an important factor in the application, we cannot substitute sintered material for laminated sheet-metal structures. Mr. Peters' remarks concerning the limitations of machine parts were well taken. The emphasis of the limitations makes it easier to define clearly what we can do and-what the advantages are of machine parts made of metal powders. When I mention metal-powder machine parts, I mean those of relatively high density, although complete elimination of porosity is not possible at this time. The limitations of the field for this type of parts are largely economical. I believe that Mr. Langhammer has made that point very clear. The following questions are very often asked: How large a part can you make? How close can you hold the dimensions ? How fast can a part be produced? In a majority of the cases, it depends on the cost at which the part can be produced. A large variety of shapes and sizes of a number of materials can be formed. However, the main requirement in this field of endeavor is whether this can be done more economically by powder metallurgy than by other manufacturing methods. As a general indication, it may be stated that densities up to 95 per cent of that of rolled material can now be produced commercially in simpler parts. Tolerances of plus or minus 0.001 in. are common, but where special conditions justify, closer tolerances can be held; we are producing a part of which one dimension is held to 0.0003 inch. Finally, as far as maximum size is concerned, technically this would depend on the capacity of the press and furnace equipment available. Actually, we find that the economical limit of powder-metallurgy machine parts is approximately one pound. From there on, each individual case must he studied on its own merits.

Jan 1, 1945

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave., Chicago, 111. '28 Bayless, William S Russ Bldg., San Francisco, Cal. '28 Bean, Louis, H 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J Room 604, 6 N. Clark St., Chicago, III. '28 Benwell, Oswald F Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher. Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H., Banker, Pres., Allen County State Bank Iola, Ran. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1934

By Charles M. Ryder

In presenting this paper to the Institute I beg to mention, first, the results which I have obtained and the apparatus which I have employed, and to follow this with a brief description of the steps by which I hare perfected this process. My present mode of testing is as follows: I obtain, either from the furnace or from the finished product in any stage in which it may chance to be, a small test-piece, usually about 3/4 of an inch square by 3 1/2 inches in length. I place this test-piece upon the poles of an ordinary electro-magnet, for about one minute, and thus magnetize it to its extreme limit. I then place it upon an indicator (which I will shortly describe), on which indicator there is already placed a piece of steel of similar form which has been magnetized in the same manner, the percentage of carbon of this second piece being definitely known. I then, by means of a scale, which forms part of the indicator, marked in degrees of carbonization, read the exact percentage of carbon contained in the piece under examination. My apparatus consists of an ordinary electro-magnet, connected with a suitable battery of moderate power, by which I magnetize the pieces as before described, and of an indicator which consists of a magnetic needle suitably mounted or suspended, so that it is free to deviate a few degrees only from the zero point, and having a rest, which is used to check the vibrations when in use, and to support its weight when not in use. At a right angle to the natural position of the needle I have a scale about 3 feet long, the zero point of which coincides with the natural position of the needle. This scale is marked in each direction from the zero point in degrees of carbonization. The marking of the scale is in accordance with the following rule: Taking the carbonization of the steel as a basis, I maintain the same proportion between the squares of the distances on the scale as exists between the percentages of carbon in the steel, for instance, if .08 of

By Charles M. Ryder

IN presenting this paper to the Institute I beg to mention, first, the results which I have obtained and the apparatus which I have employed, and to follow this with a brief description of the steps by which I have perfected this process. My present mode of testing is as follows : I obtain, either from the furnace or from the finished product in any stage in which it may chance to be, a small test-piece, usually about 4 of an inch square by 3 1/2 inches in length. I place this test-piece upon the poles of an ordinary electro-magnet, for about one minute, and thus magnetize it to its extreme limit. I then place it upon an indicator (which I will shortly describe), on which indicator there is already placed a piece of steel of similar form which has been magnetized in the same manner, the percentage of carbon of this second piece being definitely known. I then, by means of a scale, which forms part of the indicator, marked in degrees of carbonization, read the exact percentage of carbon contained in the piece under examination. My apparatus consists of an ordinary electro-magnet, connected with a suitable battery of moderate power, by which I magnetize the pieces as before described, and of an indicator which consists of a magnetic needle suitably mounted or suspended, so that it is free to deviate a few degrees only from the zero point, and having a rest, which is used to check the vibrations when in use, and to support its weight when not in use. At a right angle to the natural position of the needle I have a scale about 3 feet long, the zero point of which coincides with the natural position of the needle. This scale is marked in each direction from the zero point in degrees of carbonization. The marking of the scale is in accordance with the following rule: Taking the carbonization of the steel as a basis, I maintain the same proportion between the squares of the distances on the scale as exists between the percentages of carbon in the steel, for instance, if .08 of

Jan 1, 1877

By H. W. Maynor, C. J. McHargue

DURING the course of an investigation of materials suitable for use as thermocouples at elevated temperatures by one of the authors, several nlolybdenum-rhenium alloys were prepared. Micrographs of an annealed alloy containing 25 pct Re (intended concentration; analysis not obtained) showed a number of twins, Fig. 1, suggesting a face-centered cubic structure. This note reports the structure and recrystallized wire texture of an alloy containing 25 wt pct Re. Alloys were prepared from 99.9 pct Mo (Fansteel Metallurgical Corp.) and rhenium obtained from the University of Tennessee (purity unreported). Powders were combined and briquetted at 56,000 psi and sintering was carried out at 2400°C for 5 hr in vacuum. Ingots so prepared were swaged at 982.2" to 1037.8oC into wires 0.036 in. diameter, a reduction in diameter of 85.6 pct. These wires were vacuum-annealed 1 hr at 2000°C. A North American Philips 114.59 mm powder camera and nickel-filtered copper radiation were used for structure determination. For the texture determination a Laue-type camera was used with zirconium-filtered molybdenum radiation and, because of the high background, aluminum foil was mounted next to the film. Exposures were taken with the wire perpendicular to the X-ray beam and tilted by 10". It was found that the X-ray pattern could be indexed on the basis of a face-centered cubic structure. Because of difficulties associated with obtaining a good X-ray pattern for this material, accurate parameter determinations were not made. An indicated parameter value of 3.70A was obtained. The X-ray data are given in Table I. The annealed wire texture was observed to be a sharp [111] texture. The spread about this fiber axis was k8" at the surface of the 0.036 in. wire. The annealed wire textures of aluminum have been reported as retention of the [Ill] deformation texture for anneals below 500°C and a new [1121 texture for anneals above 600°C.1 In copper wires, with a [Ill] plus [loo] deformation texture, results indicate a retention of this texture for annealing at lower temperatures and new components or the disappearance of components for annealing at higher temperatures.' The presence of the strong [I111 texture in the molybdenum-rhenium alloy after a 2000 °C anneal suggests that the deformation texture was the same. Acknowledgment The wires used in this study were prepared and heat-treated at the Institute for Atomic Research, and Ames Laboratory, Iowa State College, and the authors wish to express their thanks to the Institute for allowing the use of the material and permission to publish the results.

Jan 1, 1954

For the year ending February, 1919 PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. PAST PRESIDENTS L. D. RICKETTS, NEW YORK, N. Y. PHILIP N. MOORE ST -Louis, Mo FIRST VICE-PRESIDENT C. W. GOODALE, BUTTE, MONT.. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y.

Jan 6, 1918

Executive J V W. REYNDERS, Chairman WILLIAM H. BASSETT E DEGOLYER H C BELLINGER RICHARD PETERS. JR. Finance H. A. GUESS GEORGE OTIS SMITH, Chairman F. JULIUS FONS Admissions GEORGE D. BARRON, Chairman DAVID LEVINGER P. A MOSMAN El K MASTERS J. A. SINGMASTIIR Alternates F. G. BREYER C W HAMILTON F. E PIERCE

Jan 1, 1923

[E. O'C. Acker '86 Jinzoc Adachi ‘88 *Truman H. Aldrich '78 Walter H. Aldridge '89 Anson W. Allen ‘87 *John H. Allen '84 William R. Appleby '90 *W. Lawrence Austin '82 *W. SAyres ‘73 David Baker '86 *John Henry Banks .83 Henry C.Banon '90 Alonzo F.. Bardwell '89 Walter A. Barrows ‘90]

Jan 1, 1940

By J. A. Berge, R. S. Mateer, R. G. Aspden

IN a study of the cold-rolling characteristics of iron-base alloys with 3 to 12 pct Al, the influence of aluminum content on the cold-rolling textures was evaluated. This work was undertaken to determine if binary iron-aluminum alloys possessed cold-rolling textures similar to other body-centered-cubic alloys and to contribute additional information on the effect of solute concentration on the cold- rolling textures. Gradual changes in cold-rolling textures with an increase in solute content have been observed in copper1 and in titanium.2 Iron-base alloys containing 3.0, '6.0, and 12.0 pct aluminum were vacuum-induction-melted in a magnesia crucible and permanent-mold cast. The materials used were high-purity electrolytic iron and 99.99 pct grade aluminum. Each ingot was 1 in. square in cross section by 12 in. in height. The bottom half of each ingot was soaked for 1 hr at 1000°C and rolled at 1000°C to a thickness of 0.055 in. with the long axis of the ingot parallel to the rolling direction. The strip was reheated between passes to maintain a rolling temperature of 1000°C.

Jan 1, 1960

By Fred C. Bond, Walter Maxson

Since the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. Standard Ball-mill Grindability Tests The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill .in all tests is 700 C.C. of the packed minus 6-mesh roll product, and the number of grams occupying 700 C.C. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity- to be expected from a given mill is calculated by comparing the grindability with that of a similar standard ore whose performance characteristics arc known. No satisfactory general formula for convertillg standard grindabilities into corn; rnercial power-consumption values has been

Jan 1, 1943

By Walter Maxson, Fred C. Bond

Since the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. Standard Ball-mill Grindability Tests The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill .in all tests is 700 C.C. of the packed minus 6-mesh roll product, and the number of grams occupying 700 C.C. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity- to be expected from a given mill is calculated by comparing the grindability with that of a similar standard ore whose performance characteristics arc known. No satisfactory general formula for convertillg standard grindabilities into corn; rnercial power-consumption values has been

Jan 1, 1943

By Arthur F. Wendt

In the manufacture of charcoal-blooms, washing or cleansing of the ore from adhering gangue has been practiced for many years. A sluice-box is even to-day used for that purpose in the Southern Appalachian Mountains. For the Lake Champlain bloomaries hard magnetic ores are crushed with stamps and then sluiced or jigged in hand-jigs. The stamps used in the Lake Champlain region are of the most primitive kind. They consist of a trip-hammer, dropping on a perforated cast-iron plate, through which the crushed ore escapes. Only friable rock can thus be successfully treated. To render the raw ore friable, a calcining or burning in piles on a bed of cordwood is resorted to. An expense of 35 cents per ton of crude rock treated is thus incurred. The crushed ore is shovelled or otherwise fed into jigs without previous sizing, except such as is incidental to crushing through the perforated bottom of the stamping-machine. In jigging this ore, it is allowed to pass through the bedding into the "hutch." The tailings are scraped off and wasted. They contain a large percentage of fine ore. In many instances, this is regained by subsequent sluicing. Such was the condition of the industry, when the writer's attention was first called to it in 1882. No attempt had been made to introduce into thiS branch of ore-dressing the notable improvements adopted in concentrating the ores of other metals. The result of the writer's investigations was the building in 1882 of the "Crown Point Separator." At the Crown Point Mines, N. Y., lean ore unfit for the blastfurnace (containing less than 331/3 per cent. of iron), was concentrated and used in the bloomary connected with the mines. The ore was burned here as elsewhere, and treated as described. The plant designed by the writer for Crown Point, is nearly a counterpart of that since erected by Messrs. Copeland and Bacon, contractors, for the Theal mine, Putnam County, New York, which is illustrated by the accompanying plate. The only difference is in

Jan 1, 1885