Search Documents

By W. C. Winegard, E. L. Holmes

The effects of the solute elements lead and bismuth on grain growth in zone -refined tin have been investigated. At low temperatures, viz. below 160°C. or at high concentrations, viz. greater than 0.03 at. pct, the temperature dependence of grain growth was found to be constant. A correlation was found to exist between the rates of grain growth in the presence of solute impurities and the factor [C Ir - 1]2 , where C is the solute concentration, r is the radius of solvent atom, and r' is radius of solute atom. It is shown that the Liicke and Detert theory does not give a satisfactory explanation of the results obtained. INVESTIGATIONS of grain growth in zone-refined lead and tin and some effects of solute elements on grain growth in these metals have been reported by Bolling and winegardly2 and Holmes and winegard? The present investigation is an extension of the previous work, and was undertaken to provide additional results which might make it possible to discover the mechanism whereby the rate of grain growth is affected by the presence of foreign solute atoms. The experimental procedure was exactly the same as that described previously.3'4 Figs. 1 and 2 show the results obtained with lead and bismuth additions over the same temperature range, viz. 167" to 220°C, as that used for the investigation of grain growth in zone-refined tin.3 Fig. 3 shows the results obtained for zone-refined tin and for this tin with lead solute additions over an extended temperature range. DISCUSSION OF RESULTS As mentioned previously,3 the character of grain growth in the particular zone-refined tin used in these experiments appears to change as the temperature of annealing falls below about 160°C. The grain growth became somewhat irregular and was characterized by a jaggedness of many of the grain boundaries. The reason for this change is not known, but may be due either to residual impurity effects or possibly an oxide precipitation. It was obvious that normal grain growth only occurred in the zone-refined tin through the high-temperature range 167" to 220°C, and so the effects of solute atoms on grai11 growth over the two temperature ranges will be discussed separately. a) Effect of Impurity on Grain Growth in the Temperature :Range Above 167°C. It is apparent from Figs. 1 and 2 that, for low concentrations of solute, the rates of grain growth tend towards a common value as the melting temperature of tin is approached. As the concentration of lead is increased, the rate of grain growth close to the melting temperature is also reduced, and at high concentrations the temperature dependence of the rate of grain growth appears approximately constant. It should be noteil that the effect of bismuth is greater than that of the same concentration of lead, but both these solutes have a smaller effect on the rate of grain growth than silver, as seen from an earlier investigation of Holmes and Winegard. It should

Jan 1, 1962

By Charles Y. Clayton

A study of the literature shows that the greater part of research work on annealing of cold-worked iron has been for the purpose of studying the effect on grain-size and properties other than hardness. No reference has been found of experimental work of the same nature as that explained in this short paper. The material used throughout was Vismera iron, an iron containing 0.03 carbon and made several years ago by the Inland Steel Co. One-half inch stock was cut into cylinders % in. long. The cylinders were then compressed for 60 sec. in a Reihle testing machine under loads as indicated below: CoMPressiON, Average Length, Series Pounds Inches 1 10,000 0.693 2 15,000 .599 3 20,000 .501 4 25,000 .426 5 30,000 .378 6 35,000 .351 7 40,000 .311 Fig. 1 shows these cylinders after compression. Each series consisted of 17 specimens lettered 0, B, C, D, E, F, G, H, I, J, K, L, M, N, P, Q and R. One specimen of each series was reserved for study of the properties in the cold-worked condition. The other specimens were annealed in a Hump furnace for 1/2 hr. at the following temperatures: TEmpeRa- TempeRa- Letters tuRe,° C. LettERs tuRe °C. B............................... 250 J.............................. 650 C............................... 300 K............................. 700 D............................... 350 L.............................. 750 E............................... 400 M............................. 800 F................................ 450 N............................. 851 G............................... 500 0. . :........................... 900 H............................... 550 P.............................. 950 I................................ 600 Q............................. L000

Jan 1, 1926

By R. L. Stephenson

The effect of fabrication variables on the creep-rupture properties of TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C), Cb-TZM [columbium-modified TZM (7140-1.5 pct Nb-0.5 pct Ti-0.8 pct Zr-0.05 pct C)], and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C) has been studied at 982º. 1093º, 1204º, and 1315°C for rupture times up to 1000 hr. The creep tests were performed in vacuum creep furnaces, employing cold-trapped oil-diffusion pumps, operating at pressures 2 X 10-7 tory. After-test chemical analyses showed no significant changes in interstitial content. The creep-rupture properties of TZM, fabricated according to current mill practice, were determined in the stress-relieved and in the re crystallized conditions to provide control data. Specimens of TZM, Cb-TZM, and TZC fabricated according to each of two experimental fabrication schedules were then tested. The schedules differed in terms of in-process annealing temperatures and warm -working temperatures. The data make several conclusions evident. Fabrication variables do indeed have a profound effect on the long-time creep-rupture properties of molybdenum alloys. Strengths of these alloys compare very favorably with those of other refractory metal alloys in the temperature range studied. FOR several years we have been engaged in the evaluation of the creep-rupture properties of promising refractory metal alloys. We consider the determination of these properties to 1000 hr at several temperatures necessary for a valid comparison. Such an evaluation indicated that the creep strengths of Mo-0.5 pct Ti and TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C) compare favorably with those of other refractory metal alloys. Tensile and recrystallization data of other investigators1,2 show an effect of fabrication variables. More specifically, those fabrication schedules which produce high strength through work hardening exhibit the least thermal stability. A similar conclusion was reported by perkins3 for Cb-TZM. This would lead one to expect that, in terms of creep, those materials showing higher strength at short times and low temperatures would exhibit lower strength at long times and high temperatures. If these expectations were fact, a substantial improvement could be made in these alloys by optimizing their fabrication schedule in terms of their anticipated service temperature. We therefore undertook a study of the effect of fabrication variables on the long-time creep properties of TZM, Cb-TZM (Mo-1.5 pct Cb-0.5 pct Ti-0.08 pct Zr-0.05pct C) and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C). MATERIALS All materials used were supplied by the Climax Molybdenum Co. of Mich. Our original intention was to test the same heat of each alloy in different conditions. Fabrication difficulties prevented this; however, heats with nearly identical analysis were selected. The compositions of the materials used are listed in Table I. All materials were supplied in the

Jan 1, 1970

By Edgar G. Hill

Much has been written and said recently about the methods used and materials and equipment employed in building the long tubes that criss-cross a great part of the United States, like the pattern of a spider's web. This paper will discuss the fundamentals of design of these lines from the economic as well as the engineering viewpoint, pointing out the effect of the volumes transported, and the load factor, on the unit costs of transportation, as well as the effects on costs of the character 01 the fluids the lines are called upon to handle. Generally speaking, crude-oil pipe lines carry oil from the producing fields to the refineries. Sometimes part of the journey is by pipe line to a coastal point and tank ships are employed for the rest of the trip. The main lines of directional flow of crude oil through pipe lines in the United States are shown on Fig. I, but this, of course, does not always show individual pipe lines. Basic Formula for Flow OF Crude Oil The laws governing the flow of crude oil through pipes are well known. The basic

Jan 1, 1942

By Edgar G. Hill

Much has been written and said recently about the methods used and materials and equipment employed in building the long tubes that criss-cross a great part of the United States, like the pattern of a spider's web. This paper will discuss the fundamentals of design of these lines from the economic as well as the engineering viewpoint, pointing out the effect of the volumes transported, and the load factor, on the unit costs of transportation, as well as the effects on costs of the character 01 the fluids the lines are called upon to handle. Generally speaking, crude-oil pipe lines carry oil from the producing fields to the refineries. Sometimes part of the journey is by pipe line to a coastal point and tank ships are employed for the rest of the trip. The main lines of directional flow of crude oil through pipe lines in the United States are shown on Fig. I, but this, of course, does not always show individual pipe lines. Basic Formula for Flow OF Crude Oil The laws governing the flow of crude oil through pipes are well known. The basic

Jan 1, 1942

At the Kidd Creek mine operated by Ecstall Mining, Ltd. near Timmins, Ontario, Honeywell has installed a sophisticated new quick- thinking computer system that keeps tabs on conditions along three separate processing streams at once and relays continuous 60-second data to the mill operator. Believed to be the first of its kind, the system picks up data from two independent x-ray spectrometers simultaneously. A digital computer from Honeywell's Computer Control Division receives and interprets real-time information gathered by online x-ray analyzers, and the system then advises control room operators of the relative amount of each of five elements at five points in each of the three process streams. The system is reported to provide a quantitative analysis of the five elements at a given point in the process within one minute-which is about 120 times as fast as a chemical laboratory assay could be performed. With this instant data at his command, the mill operator can make timely process adjustments to correct any deviation from optimum flotation results, thus salvaging valuable minerals that would inevitably be lost with slower detection methods. The minerals recovered at Kidd creek are copper, lead, iron, silver and zinc.

Jan 8, 1968

United Engineering Trustees, Inc Engineering Foundation Engineering Societies Research Board Other Committees United Engineering Trustees, Inc. ARTHUR S. DWIGHT GEORGE D. BARRON J. V. N. DOER Engineering Societies Library Board ROBERT PEELS PHILIP W. HENRY GEORGE C. STONE JOSEPH E. POGUE The Engineering Foundation H. C. BELLINGER GALEN H. CLEVENGER J. V. N. DORR

Jan 1, 1929

By J. J. Gilman

THEORIES of fracture in metals have been based primarily on the dependence of fracture strength on grain size. This dependence was first observed by Masing and Polanyi.l These workers, as well as 0rowan12 and Davidenkov and Wittman,' thought the grain size could be equated with the crack size in the Griffith condition for crack propagation.4 In this way they could account for the observed proportionality between fracture stress and the reciprocal square root of the grain size. The chief results of recent investigations of the fracture strength of polycrystals are summarized in Fig. 1. Low for iron,5 Petch for iron,' Greenwood and Quarrel for zinc, Petch and Zein for zinc,' and Hauser, Landon, and Dorn for magnesium'' have all found that the fracture stress of a polycrystal is proportional to the reciprocal square root of the grain size. Also, they find that, for large grain sizes, the fracture stress lies near the extrapolation of the yield-stress curve determined at small grain sizes; where measurable plastic strain precedes fracture. Low9 has gone a step further and shown that, in Range 1, the fracture stress in tension is almost identical to the yield stress in compression for a given grain size. Homes and Gouzou, 10 and Low also have shown that, in Range 2 of Fig. 1, microcracks form when the yield stress is reached, but they do not cause failure until the stress reaches a much higher value. The fact that yielding always precedes fracture suggests that fracture is induced by plastic flow. A mechanism by which this might occur was first proposed by Zener.11 He pointed out that blocked dislocations would cause stress concentrations which might cause fracture. The blocking would be caused by grain boundaries. This idea has been developed by Eshelby, Frank, and Nabarro,12 by Koehler,13 and by Stroh.14 By means of etchpits blocked dislocations have been observed in brass by Jacquet,15 in zinc by Gilman,16 and in lithium fluoride by Gilman and johnston. The blocked-dislocation theory and the experiments that bear on it have been summarized by Mott.18 One of the strong points of the blocked-dislocation theory is that it can explain the grain-size dependence of the fracture stress in a natural way. However, Low9 has pointed out that the theory is not satisfying when it is considered quantitatively. Gilman10 also has criticized the theory and presented an alternative interpretation of the relation between fracture stress and grain size. Since the blocked-dislocation theory is not the only theory that can explain in the grain-size effect, it is necessary to find other evidence either to support or deny it. In this investigation the following points were studied: 1) If blocked dislocations normally cause fracture, then the fracture stress ought to be very high in the absence of plastic glide. Is it? 2) If dislocations must be blocked in order for metals to fracture, then certain types of grain

Jan 1, 1959

By Fathi Habashi

Chalcopyrite can be readily leached with HNO3, but the recovery of elemental sulfur does not exceed 50% under the most favorable conditions. Preheating at 500°C in a slightly reducing atmosphere increases the recovery of elemental sulfur to about 65%. Chalcopyrite can also be treated with HNO3 in a pressure reactor at 110°C to solubilize selectively the copper while iron remains in the residue as an oxide. The recovery of elemental sulfur also improved when preheated chalcopyrite is treated in this way. Stainless steel should be an adequate material of construction.

Jan 1, 1974

By Milton E. Wadsworth, T. D. Chatwin

Bulk density variations can usually be minimized by properly mixing the material before moisture measurement. The measuring of moisture on material being with- drawn directly from storage bins requires some form of bulk density correction. In Bethlehem's pellet plants continuous automatic bulk density correction and uniform feed-rate control are obtained with Bethlehem's patented Bin Level Control System. With this sys- tem a single probe, suspended or inserted in the bin, senses whether material is at the proper level in the bin and automatically regulates filter speed to control the filter-cake discharge rate to maintain this level. The level of concentrate in the filter-cake bin can thereby be controlled to within ± 1/2 in. of the point of contact between the concentrate and the probe. Material thickness on the conveyor does not have to be controlled accurately and mix compositions can vary widely as long as they do not contain variable amounts of water-soluble electrolytes. In sinter plants, errors caused by changes in normal feed rate and bed height are minimized by counter-weights that permit the free-floating to maintain a uniform contact pressure on the mix. Large changes in mix resistance can be taken care of either by resetting the control point or by adjusting the calibration control.

Jan 9, 1968

By L. P. Teas

As sphalerite is such a common constituent of many types of ore, the present investigation was undertaken to determine what its relations are to the other minerals in the deposits, and also whether these are of any genetic significance. The data presented herewith were obtained from a mineralographic study of about 200 ore specimens from some 43 different localities, represented by suites of specimens in the Cornell University collection. These, grouped according to their genesis, were as follows: I. Contact-Metamorphic Deposits.-Silver City, N. M.; Kelly, N. M.; Silver Bell, Ariz.; Bingham, Utah; Agaguca, Michoacan, Mex.; Matehuala, Mex.; Sombreretti mine, Mex. II. Deep-Vein Zone Deposits.-Mineral, Louisa Co., Va.; Edwards, N. Y.; Chestnut Yard, Va.; Allah Cooper mine, Louisa Co., Va.; Globe, Ariz.; Moyie, B. C.; Rossland, B. C.; Broken Hill, N.S.W.; Weedon, Que.1 III. Intermediate-Vein Zone.-Park City, Utah; Leadville, Colo.; Butte, Mont.; Santa Barbara, Mex.; Red Cliff, Colo.; Burro Mountains, N. M.; Idaho Springs, Colo.; Blue River, Ore.; Rye, Colo.;1 Slocan district, B. C.; Freiberg, Ger.; Clausthal, Ger: IV. Shallow-Vein Zone.-Ouray, Colo.; Goldfield, Nev., Zacatecas, Mex.; Field, B. C.; Kapnik, Austria; Frontenac mine, Kingston, Ont. V. Meteoric Water Deposits.-Joplin, Mo.; Southwest, Wis.; Austinville, Va.; Crittenden County, Ky.; Ridgeburg, Pa.; Moresnet, Belgium. It is not supposed that the investigation of such a limited number of occurrences may warrant conclusive and universal generalizations, but the conclusions reached are believed to be reliable in so far as the specimens, that were examined are concerned.

Jan 11, 1917

By R. S. Shoemaker, F. W. McQuiston

CARLIN GOLD MINING COMPANY 1974 Operating Data to October MINE LOCATION: 40 miles from Elko, Nevada ORE DESCRIPTION: Gold with minor amounts of mercury occurring in siltstone and carboniferous limey shales. TYPE OF MINE: Open pit ORE HAULAGE TO MILL: By trucks up to a distance of 12 mi1es MILLING CAPACITY: 2500 tons per day ORE GRADE: 0.20 oz per ton oxide ore 0.25 oz per ton carbon type ore PRODUCTS: Gold bullion 993 fineness, by product quicksilver RECOVERIES: Oxide ore 887'0 Carbon ore 83% POWER FOR GRINDING: 7 Kwh/T POWER, other than grinding: 14 Kwh/T WATER SUPPLY: Pumped from wells 2- 112 miles through 13,000 ft of 8" buried pipe 6 ft underground. Consumption 0.60 tons of new water per ton of mill feed. TAILINGS: By 10" woodstave pipe a distance of 2500 ft to mine waste filled dam. RUNNING TIME: 10 ft x 10 ft mill on oxide ore, 98% 7 ft x 8 ft mill on carbon ore, 937'0 Principal causes of lost time, power outages and problems of feeding gaseous chlorine to carbon ore agitators. LABOR, TONSIMAN SHIFT: See detailed data sheet ILL BUILDING DESCRIPTION: Framed structural steel with sandwich type walls of marine plywood, then packaged pre - fabricated insulation and outer sheeting of galvanized corrugated steel.

Jan 1, 1975

By A. E. Jenkins, L. A. Baker, N. A. Warner

The electromagnetic levitation technique has been successfully applied to rate studies of the de-carburization of liquid Fe-C alloys from 5.5 to zero pct C at 1660°C using gas mixtures containing 1 to 100 pct CO2 with CO or helium as diluents. The rate was shown to be independent of carbon concen -tration in the melt and only slightly affected by total pressure. The results were shown to be consistent with control either wholly or predominantly by gaseous diffusion. As well as avoiding side reactions with the crucible, levitation allowed precise calculation of reaction rates since the geometry of the system was accurately known. It also enabled interpretation using the established mass-transfer correlations for a gas flowing past a single sphere, The existence of gaseous-diffusion control and the extremely high rates of reaction reported for gas flowing past small spheres are of great practical significance in relation to current investigations into the use of spray-refining techniques in continzcous steelmaking. PREVIOUS work on the kinetics of carbon removal from liquid iron has generally involved the use of oxygen as the gaseous oxidant. Investigations have been made on commercial steelmaking furnaces and in addition laboratory-scale experiments have been attempted with a slag phase present. The general lack of agreement and the obvious difficulty in interpreting the results is at least partly due to the complexity of the systems used. This work has been reviewed by carter1 and more recently by Bods-worth2 and ward.3 The gas-liquid metal reactions have also been studied with slag-free melts by the conventional technique of blowing oxygen onto the melt contained in a crucible. The reaction between the oxidant and carbon could be followed by sampling either the melt or the gas phase. Side reactions with the crucible material have precluded direct interpretation of the results. Fujii, 5-7 using O-A mixtures, attempted to correct for the crucible reaction and reported that the reaction between carban and oxygen occurred at the melt surface and was controlled by gaseous diffusion for carbon contents greater than a critical value and by carbon-diffusion control in the metal for carbon contents less than the critical. The critical value was given as approximately 0.15 pct C. However, whereas this was the case for oxygen contents in the gas stream up to 10 pct, between 10 and 20 pct the rate was found to be approximately independent of oxygen content, and Fujii attempted to explain this observation by postulating the presence of an oxide "film".7 Turkdogan et a1.' have studied iron fuming during decarburizing and suggested gaseous-diffusion control of the reaction above a critical carbon concentration, given as approximately 2 pct C. Filippov9-12 reports in a similar manner to Fujii but makes no mention of the crucible reaction with the carbon in the melt, even though this would be expected with the temperature, crucible material (MgO), and carbon contents used. Both CO2 and O2 were used as oxidant gases. In the present work the decarburization of liquid Fe-C alloys was studied using an adaptation of the electromagnetic levitation technique, and thus the complexities introduced by crucible side reactions were eliminated. In this technique a single sphere of the Fe-C alloy is freely suspended and heated by electromagnetic induction in a flowing stream containing the oxidant gas. The full range of carbon levels up to saturation was studied, the temperature of the melts in this instance being held constant at 1660°C. The oxidant was CO2 which was used either pure or in association with a diluent gas, the total gas pressure being maintained either at 1 atm or at a reduced pressure. Thus the reaction under study was:

Jan 1, 1964

By J. C. Sarace, S. M. Sze, C. R. Crowell

Thin films of tungsten 077 n-type germanium, silicon, and gallium arsenide were obtained by reacting tungsten hexafluoride with the semiconductor surface in an argom atmosplrere at temperatures between 325° and 400° C. Capacity-voltage, current-iloltage, and photoelectric measurements were used to investigate the characteristics of the tungsten -semiconductor diodes thus Produced. The junctions are shown to he very close to ideal Schottky barlp/ers with barrier heights measured with respect to the Fermi energy of 0.18, 0.65, and 0.78 1.1 jar W-Ge, W-Si, and W-GaAs, respectively. The electrical properties of the W-Si interface show no deterioration when heated to 1000°C in dry forming gas for 5 min. A theoretical value of the Richardson constant, A, appropriate to the semiconductor-hand structure has been used in evaluating the current-voltage characteristics. ThE W-Si surface-barrier diode was initially proposed for investigation because the eutectic temperature with silicon (1400°C) is much higher than that in the Si-Au system 1370°C).1 This would permit more flexibility in heat treatment and possibly provide greater reliability at elevated temperatures. The lower work function of tungsten (4.54 ev)2 compared with that of gold (4.78 ev)3 also suggested that a lower barrier height would be obtained with tungsten and hence a lower forward bias and lower minority carrier injection ratio for a given current density. The investigation was extended to include the characterization of W-Ge md W-GaAs surface-barrier diodes. The tungsten films have been produced by reacting WF6 with germanium, silicon, and GaAs surfaces in an argon atmosphere at temperatures from 300° to 500°C.4 This process is a very satisfactory alternative to the relatively difficult process of evaporating tungsten films in vacuo. To ensure an adequate electrical characterization of the tungsten-semiconductor interface, three types of barrier-height measurements have been performed. The mutually consistent results obtained lead to the conclusion that the tungsten-semiconductor junctions are indeed of the Schottky type. EXPERIMENTAL PROCEDURE The apparatus used for producing tungsten films is shown schematically in Fig. 1. It consists of an argon carrier gas line to which metered amounts of tungsten hexafluoride can be rapidly added. The mixture passes through a heated reaction tube containing the semiconductor slices and is exhausted to a hood. The argon is purified by passage through a 6-in. column of titanium turnings maintained at 800°C. The tungsten hexafluoride dispensing arrangement was designed by V. C. Garbarini and W. R. Bracht.4 A measured amount of liquid tungsten hexafluoride is injected into the argon stream and vaporizes. The mixture passes through a sodium fluoride absorption cell to remove traces of hydrogen fluoride, then into the nickel reaction tube. The tube is 12 in. long with an inside diameter of 1/2 in. The center section is heated by a furnace of the self-supporting wire-filament type. It was chosen for its rapid heatup and cooling. The wall thickness is 10 mils except for a 3-in. hot zone which is 30 mils thick to reduce thermal gradients along the length. The samples to be coated are placed on a sapphire plate and centered in this section. The tungsten is deposited with the following sequential steps: the loaded reaction tube is flushed with argon at a rate of 500 cu cm per min and heated to 370°C. Then 0.45 g of liquid tungsten hexafluoride is injected into the argon stream. The samples are held at this temperature for 2 min. The tube and samples are then cooled to room temperature and the samples removed. Tungsten films were grown on (111) faces of silicon and germanium polished with Linde A abrasive and lightly etched with HF-HNO3. The GaAs surfaces were (100) faces chemically polished with a H2SO4-H2O2 solution. The films have typical sheet resistances of 0.2, 8, and 15 52/0 when grown on germanium, silicon, and GaAs, respectively. After the tungsten deposition, ohmic contacts were alloyed on the back surfaces of the wafers. Ohmic contacts to the germanium and silicon were obtained by alloying Au-Sb at 370°C, ohmic con-

Jan 1, 1965

By H. H. Smith, G. J. Danek, M. R. Achter

Nickel, Type 316 stainless steel, and copper show decreases in reversed bending fatigue strength with increases in air and oxygen pressure. The leveling off of the log N us log p curve for nickel at 300" and 816°C is discussed in terms of a model in which surface saturation gives rise to a critical pressure. A metallographic study indicated that the effect of environment on crack initiation and growth rates is a function of temperature. It is shown that small amounts of impurities in inert gases may substantially reduce the fatigue strength of nickel. 1n a previous investigation1 of high-temperature bending fatigue in air and in vacuum, reversals in the effect of environment with changes in test conditions were atrributed to a mechanism consisting of two processes acting in competition. One of them, oxidation strengthening, has been demonstrated in a straightforward manner by measuring the rupture strength of a sintered nickel-oxide bond.' The detailed operation of the other process, facilitation of crack propagation by surface absorption of oxygen, is uncertain. Thompson et UZ advanced the possibility that the formation of an oxide layer prevented rewelding of cracks during the compressive part of the cycle, while Wads worth and Hutchings4 further proposed that the reaction of oxygen with atoms at the tip of the crack helped the metal to break there, a possibility which has also been advanced to explain crack formation in creep.5 A difficulty in arriving at a mechanism for this lowering of fatigue strength in air is the inconsistency of some of the data. For example, Wadsworth and Hutchings4 found an approximately linear decrease of log cycles-to-fracture (N) with an increase of log pressure-of-air (p) for copper and aluminum at room temperature, while snowden,' although finding a similar linear dependence for aluminum, observed a stepped curve for lead. Between l0-' and 10"1 torr there is a sharp decrease in the fatigue life of lead with increasing air pressure, but plateaus, signifying no dependence on pressure, are found at higher and lower pressures. If, as discussed elsewhere: these environmental effects arise from the adsorption of gas on crack surfaces, it would be expected that as the pressure is increased a saturation point would be observed, beyond which there is no further effect. To gain further information about the form of the log N vs logp curve, it was decided in the present investigation to repeat this type of measurement at elevated temperature on nickel, copper, and Type 316 stainless steel. An additional object of this program was

Jan 1, 1963

By C. G. Dunn

The measurement of interfacial teusions or grain boundary energies in metals is an important metallurgical problem, especially since it bears on growth and nucleation processes. Statistical methods of measuring equilibrium grain boundary angles, which relate interfacial tensions, have been used by some investigators1'2 but more direct methods would be preferred. A direct way, based on a simple extension of a successful method of growing single crystals of silicon ferrite to predetermined orientations in flat specimens,3 is to produce three-grain specimens in such a way that the equilibrium common grain boundary will be perpendicular to the surface of the specimen. The angles to be measured then appear as the grain boundary angles in the surface of the specimen. The method of producing a single crystal specimen with a predetermined orientation is basically the same as that employed by Yoshida and Fuji-wara4 in their work on aluminum wires. The specimen, prior to any single crystal transformation, must have a matrix which will support the growth of a crystal of the desired orientation. Growth may occur through exaggerated grain growth or, if the matrix is strained a critical amount. by normal recrystallization. In either case the matrix must have stability at the temperature used to effect the transformation, this stability appearing as a long induction period for exaggerated grain growth or for the formation of recrystallization nuclei. Additional control is gained by using a high temperature gradient through which the specimen is moved at a suitable rate. To obtain the desired orientation, the specimen is fed a short way into the furnace producing one or more crystals in the hot end. After the specimen is removed from the furnace, the orientation of a crystal is determined, so that this crystal may be reoriented by properly deforming a narrow piece of the matrix between the end crystal and the rest of the specimen. This part of the specimen in the case of silicon ferrite is preferably held at red heat during the reorienting process. Fig 1 shows a specimen which is ready to be transformed into a single crystal through growth of a reoriented "seed" crystal. When the method just described is applied to the production of a three-grain specimen two crystals are grown first side by side in one end, the specimen is then reversed and the third grain grown from the opposite end. A suitable group of grains each of different orientation is one where all three grains have the same crystallo-graphic plane in the plane of the specimen. Fig 2 shows a photograph of a three-grain group prepared as described. The notches are introduced in the open ends of the grain boundaries to anchor them during the final annealing operations which ultimately should bring the grain boundaries to the lowest energy configuration. Two-grain groups with different crystallographic planes in the plane of the specimen can be similarly prepared and treated. If the two grains have different surface (gas to metal) energies per unit area, the equilibrium condition leads to a curved grain boundary.* * This feature of the problem was pointed out by J. c. Fisher. References 1. Cyril Stanley Smith: Grains. Phases and Interfaces: An Interpretation of Microstructure. Trans. AIME 175, 15. Met. Tech. TP 2387, June 1948. 2. D. Harker and E. Parker: Grain Shape and Grain Growth. Trans. A.S.M. (194,5) 34, 156-195. 3. C. G. Dunn, A. Seddon, and R. Wylie: Unpublished Work, 1946-1947. 4. Takeo Fujiwara: A Method of Producing A Long Single-Crystal Wire of Aluminum with any Desired Crystallographic Axis. Jnl. of Sci. Horoshima Univ. A, (1939) 9, No. 3, 227.

Jan 1, 1950

By Gilbert Soler

Page Introduction. By Gilbert Soler.........................657 Deoxidation of Basic Open-hearth Steel. By T. S. Washburn.............658 Slag-metal-oxygen Relationships in the Basic Open-hearth and Electric Processes. By J. S. Marsh. (With discussion)...........................672 The Total Oxygen Content of Plain Carbon Open-hearth Steel during Deoxidation and Teeming. By Michael Tenenbaum and C. C. Brown. (With discussion)......685 The Occurrence of Oxygen in Liquid Open-hearth Steel—Sampling Methods. By T. E. Brower and B. b. Larsen..........................712 Effect of Deoxidation on the Strain-sensitivity of Low-carbon Steels. By H. K. Work and G. H. Enzian. (With discussion)........................723 The Relation among Aluminum, Sulphur, and Grain Size. By C. E. Sims.......734 Some of the papers and discussions that appear on the following pages were presented at the meeting of the Iron and Steel Division in Cleveland, Ohio, on Wednesday, October 18, 1944. with L. F. Reinartz and H. K. Work as Chairmen; the remainder were scheduled for the New York Meeting of the Institute in February 1945, which was canceled.

Jan 1, 1945

By E. P. Pfleider, C. A. Dufresne

The problem of mooing open-pit ores over large vertical distances is increasing in importance because of the immense deposits being mined. Gravity fall of ore through transfer raises to central haulage points underground has advantages for certain open-pit operations, and this method is being seriously considered for the Carol Project now underway in Canada.

Jan 6, 1961

By H. Herman, M. E. Fine

Kinetics of reversion and reformation of GP I were studied resistometrically in Al-1.7 at. pct Cu. The reversion process is over in roughly 1/2 minute at 205 "C irrespective of the amount of primary aging. After reversion the occurrence of an incubation time before reaging begins has been substantiated. The reaging kinetics is drastically accelerated by plastic deformation to the specimen. An incubation time is observed only if the specimen is aged before reversion. The incubation time and the effect of plastic deformation indicate that nucleation of GP I is heterogeneous. Simple clusters of copper atoms apparently do not act as nuclei for GP I. AFTER quenching aluminum-rich copper from the solid solution range, Guinier-Preston zones of the first kind, GP I, form very rapidly at room temperature. The rate, largely controlled by the concentration of vacancies, is initially most rapid1 (that is, at the time of the first measurement: 1/2 min) and decreases with time. The nucleation is thought to be athermal. If after aging for several days the GP I is dissolved by reversion at 205°C, according to measurement of Young's modulus an incubation period is observed before GP I begins to form on subsequent aging.2 Yet if the reversion is carried out immediately after quenching, both resistivity3 and modulus changes2 show no incubation effect. The zones which form after reversion have the same structure as those which form after the quench.4 Because of entropy considerations and also the short diffusion time, the solid solution after reversion, 2 min at 205°C, is probably more highly clustered than at the original solution treating temperature, 520" to 550°C. It appears most reasonable to associate with nucleation the incubation time observed on reaging after reversion. A simple cluster of copper atoms, many of which are presumed to be present after reversion, is then not a sufficient nucleus for GP I; a GP I nucleus must contain something in addition to a cluster of copper atoms. The purpose of the present note is to give some additional experimental information concerning the incubation time and rates of reaging after reversion. The existence of the incubation time has been verified by measurement of another property, the electrical resistivity. Acceleration of reaging after reversion by plastic deformation has also been investigated. In acl.dition, the kinetics of the reversion process itself was studied. EXPERIMENTAL Electrical resistance was measured by the poten-tiometric four probe method. The 1.7 at. pct Cu alloy was furnished by the Aluminum Co. of America in the form of 1/2 in. rod. The major impurities reported by Alcoa were Fe (0.002 wt pct), Si (0.003 wt pct), and Mg (0.001 wt pct). Specimens for measuremenl of resistance were prepared by rolling to 0.010 in., cutting 2 by 0.2 in. pieces, rolling the middle pclrtions of these to 0.005 in., and splitting the 0.010 in. sections up to the reduced central section to form current and potential leads. Aluminum extension wires insulated with ceramic tubes were spot welded to the leads. The specimen was supported by the lead wires. The whole specimen assembly was annealed at 500" C in an air furnace for more than 12 hr and then aged at room temperature. This was done to assure quick and complete resolution during subsequent solution treatments. These were carried out in Houghton's "430 Temper Salt" at 520'C for 1 hr. Unless otherwise specified, quenching was accomplished by quickly transferring the specimen from a salt pot to 25°C water. Aging was carried out in a 3 liter dewar of distilled water, rotated and stirred. The temperature was controlled to +0.01°C with a thermomercurial regulator in conjunction with a transistorized relay

Jan 1, 1962

By Leonard D. Jaffe, Donald C. Buffum

THE importance of temper brittleness in alloy steels has long been realized in Europe, In the United States recognition of its importance has developed within the last several years. Many brittle failures encountered in parts made of alloy steel are undoubtedly attributable, wholly or in part, to temper brittleness. These failures have occurred particularly at low temperatures, under shock loading, and in the presence of notches, restraints and combined stresses. It has been almost universally accepted that plain carbon steels are not susceptible to temper brittleness. As a result, considerable effort has been expended in attempts to discover the manner in which alloying elements introduce temper brittleness. It is desired to raise the possibility that plain carbon steels are not only susceptible to temper brittleness, but are much more susceptible than alloy steels, in the sense that they embrittle much more rapidly. It is suggested that previous views, (that plain carbon steels are not susceptible), are based upon an erroneous interpretation of the experimental results. INTERPRETATION OF PREVIOUS DATA For many years the standard criterion for susceptibility of a steel to temper brittleness consisted of comparison of the energy absorption, in a notched-bar impact test at room temperature, of specimens that had received two heat treatments.1 One specimen (or group of specimens) was quenched, tempered, and quenched from the temper. The other specimen (or group) differed only in having received an embrittlement treatment, which might consist of a slow cool from the tempering temperature, or of an isothermal hold in the range 450-550°C subsequent to quenching from the temper. If the energy absorption of the specimen receiving the embrittlement treatment was lower than that of the specimen not given this treatment, it was said that the steel was susceptible to temper brittleness, If the energy absorptions were the same, it was said that the steel was not susceptible. Several investigators2,3 found that plain carbon steels showed negligible difference in energy absorption in such tests (at least when their manganese content was below 0.60 pct), and concluded that plain carbon steels are not susceptible to temper brittleness. Recently the deficiencies of the criterion mentioned above have been pointed out.4-6 The criterion now generally used for susceptibility to temper brittleness retains the heat treatments used in the earlier scheme, but instead of the notched-bar impact tests being made only at room temperature, they are made over a range of temperatures, covering the transition from ductile to brittle fracture, If the transition temperature of the specimens receiving the embrittlement treatment is higher than those

Jan 1, 1948