Search Documents

By W. F. NETZZEBAND

THE long-hole drill has been used for prospecting underground in the tri-State district for several years, and its value has been pretty thoroughly proved. An attempt was made to get a statement of their experience with the machine from all the operators who were known to have used the machine. The majority of them replied to the questionnaire so that this paper is practically a summary of the experience of the district, together with some practical details taken from the experience of the Eagle-Picher Lead Company. When the drill was first used by the Eagle-Picher Lead Co., it was put in low headings and was mounted on a cross-arm supported by two drill columns. This was found to be a rather awkward method of mounting, because fairly long moves were made and the same drill columns could not be used on any two successive set-ups. The machine was later moved to a mine with high headings so that this type of mounting was found to be impractical. A heavy tripod was tried and found satisfactory, provided care was taken to see that the set-up was solid. The Evans-Wallower Lead Co. and the Century Zinc Co. report using the double post set-up, but the headings are low in these mines. The Commerce Mining St Royalty Co. first used the double-post mounting in high headings by cutting a niche in the wall and setting the post in it. This proved to be a slow and expensive method and was later abandoned for the tripod. The Federal Mining & Smelting Co. has used a tripod throughout its operations. Great care must be taken in using the tripod to see that the set-up is solid. Wherever possible it is advisable to sludge in the legs and let them set a short time before the machine is put into use. Where high bottom is encountered the Eagle-Picher operator found it advisable to drill jack- hammer holes in the bottom and drive the legs into them.

Jan 1, 1930

By Hans Lundberq

WHEN geophysical methods were first employed in the search for ore deposits and oil accumulations, it was hoped that they would provide a direct means of locating such concentrations. Magnetized needles were used long ago in prospecting for magnetic iron ore, and soon after the discovery of galvanism in about 1790 attempts were made to find concentrations of valuable minerals electrically. Evidence indicating that the early geophyeical instruments were regarded merely as improved divining or dowsing rods is to be seen in the names "mineral finders," "ore finders," etc., that were applied to them. Today, appellations of this kind raise serious doubts in informed minds as to the intelligence and integrity of individuals advocating the use of such euphemistically named methods or instruments, for experience and research have shown that, geophysical, it is never a question of directly locating a given mineral but merely of delimiting its possible occurrence.

Jan 1, 1939

By V. G. Mooradian

THE diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distor-tion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-

Jan 1, 1935

By Cyril Wells, Robert F. Mehl

THE practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out 1,13 This importance ties chiefly, though by no means only, in the study of carburizing and in the study of reactions involved in the eutectoid inversion in steel The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in y-Fe and their mutual effects are measured with precision The present paper reports the results of meas¬urements of diffusion coefficients D of manganese in -y-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients [$] Data on the rate of diffusion of manganese in y-Fe have been reported by Fry2 and by Paschke and Hauttmann 3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq cm per sec at 960°, which will be shown to be incorrect by many orders of magnitude Paschke and Hauttmann gave a rough value of 9 6 X 10-8 sq cm per sec at 1400° Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon METHOD AND MATERIALS Method -The method employed is identical with that used earlier 5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded The diffusion anneals were performed in argon, except one (test 18) in which hydrogen was employed for purposes noted below The temperatures reported are accurate to about 3° and constant within I°C , the diffusion times are reported to the nearest half hour The specimens were furnace-cooled after the diffusion anneal at about 2° per min Layers, usually 0 004 in thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0 01 per cent Mn, the distances of these layers from the interface was measured to ±0 0002 in The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions e The D values calculated by these two methods do not differ appreciably 5 The Grube solution was used except in tests in which the effect of concentration upon D was greater than 50 per cent, in such cases the Matano method, which explicitly provides for the variation of D with concentration,1 is the more reliable In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer In 3 of the 30 tests, however, this is not justified, and the D values

Jan 1, 1941

By E. V. Murphree

CREATION of atomic energy, aside from its influence on war or peace, has posed these basic questions for the world: How soon can energy from atoms be harnessed to do man's daily work? How much of this power will there be, to what degree will it supplant present fuels, and what does it imply for the future of civilization? Answers to these questions may be found in part in analysis of just what atomic energy is and how far its development has come. The answers are encouraging. One of the first questions encountered in considering the application of atomic reactions is whether such reactions can be controlled. Fortunately, this has been adequately demonstrated by the operation of the Government plutonium plants at Hanford, Wash. Here nuclear reactions are carried out on a large scale involving liberation of about a billion B.t.u. per hour. This hourly heat liberation is equivalent to that obtained from about 7100 gallons of fuel oil. It has been possible to operate these plants day in and day out with the reaction controlled at the intensity desired. There should therefore be no question that, under proper conditions, reactions involving nuclear fission can be controlled.

Jan 1, 1946

By M. E. Tyrrell, Alan H. Goode

The application of a simple, two-dimensional computer technique for evaluating rock burst potential in cut-and-fill stopes was investigated. The principal purpose of the study was to compare the effectiveness of high-modulus fill and destressing as aids in the control of rock bursts. Two conclusions that are probably of general applicability are drawn. First, high-modulus fill is ineffective as a means of increasing the mine stiffness and acts to control rock bursts only if it supports enough load to reduce substantially the stresses on the unmined vein material. Second, destressing is most effective if it is performed when the vein material is near the point of failure.

Jan 1, 1975

By D. Cox, M. J. Duggin, L. Zwell

The carbides of approximate composition and Mn have been studied using X-ray diffraction techniques. Those carbides of the type (Fe,Aln)zC ave isostructural with cementite. The cell pararmeters a and c have minimum values at approximately 10 at. pd substitution of manganese for iron; no satisfactory explanation has yet been found for this phenomenon. The carbide fFeMn4)C has a monoclinic unit cell whose dimensions are close to those of ,11,15Cz A neu-troip-dij~ractiot~ study of (F'eAlrz4)C~ reveals that, like MnsCZ, it is isostructural with Pd5Bz. The iron and manganese atoms occupy the palladium atom sites, while the carbon atoms were found to have the same atomic coordinates as the hovon atoms. A neutrorr-diffraction study of indicates that the carbon-atom positions are very close to those occupied in (Fez.,ll/lr~,.3)C. In both carbides studied, tlre iron and manganese atomzs were found to be essentially randomly distributed, although, in the case of (Fe,.811fn1.2)C, it is possible that there may be a slight preference of manganese atoms for- the general (d) positions and a corresponding slight preference of iron atoms for the special (c) positions. It has been found that a complete range of solid solution exists between Fe3C and Mn3C at 1050°C,I although Mn3C becomes unstable when the temperature is reduced to 95O0C,' and can only be retained by rapid quenching. It is also known that a complete range of solid solution exists from Fe5Cz to M~SC~,~ although the stability range of carbides of the type (Fe,Mn)sCz as a function of the relative proportions of iron and manganese is not known. X-ray examinations of Oh-man's carbide3 and Spiegeleisenkristall,~ which have the approximate compositions (Fe3.67Mnl.33)C2 and (Fe3-,Mn,)C, where x lies between 0.4 and 1, respectively, have been made. The following carbides have also been studied: ] The lattice parameters determined during these investigations are listed in Table I. It is seen that carbides of the type (Fe,Mn)sCz have a monoclinic unit cell while carbides of the type (Fe,Mn)3C have an orthorhombic unit cell. It is evident that the variation of lattice parameters with manganese content is not linear for carbides of the type (Fe,Mn)3C. The coordinates of the atoms in (Fe2.7Mno.3)C have recently been determined by single-crystal analysis., The fractional atomic coordinates have been shown by Fasiska and jeffrey to be in good agreement withj those deduced from an earlier analysis of Fe3C by Lipson and etch.' However, it was impossible to determine whether iron and manganese atoms occupied ordered positions because of the small difference between the atomic scattering factors of iron and manganese. The atomic positions in Mn5Cz (Refs. 8 and 9) and Fe5C2 (Refs. 7 and 8) have been obtained only by comparisons made with the isostructural compounds P~SB~.' Since X-ray diffraction techniques were used in these investigations, accurate positioning of the carbon atoms, which have a low atomic scattering factor, was difficult. No attempt has been made to determine the atomic positions in the other carbides previously studied. It was felt that an investigation of the lattice parameters of a number of intermediate carbides of the types (Fe,Mn)sCZ and (Fe,Mn)& would be of interest. It seemed likely that a neutron-diffract ion study of such carbides would indicate whether ordering occurred between the iron and manganese atoms because of the large difference between the neutron-scattering cross sections of iron and manganese. It also seemed probable that such an investigation would provide a determination of the atomic coordinates of the carbon atoms. I) EXPERIMENTAL DETAILS Specimens, each weighing approximately 20 g, were carefully prepared according to the following proportions: The components were 500-mesh powders of 99.995 pct purity iron and spectroscopically pure carbon and a 200-mesh powder of 99.995 pct purity manganese. The component powders were intimately mixed by prolonged shaking, then each specimen was inserted into a spot-welded cylindrical container of tantalum foil, whose end was closed but not sealed. Each specimen in its envelope was then sintered at 1050° C for 24 hr in a thin-walled evacuated quartz capsule, such a time having been previously found sufficient for equilibrium to be attained.' Each specimen was then quenched in order to attempt to retain the high-temperature phase, as the literature indicates that transformations may occur on cooling. Debye-Scherrer X-ray photographs were taken of each specimen using a 114.6-mm-diam camera, Fig. 1, patterns 2 to 6. The exposure time was 6 hr using filtered iron radiation at a tube voltage of 40 kv and a tube current of 12 ma.

Jan 1, 1967

By William T. Folwell

The Lucky Friday mine east of Mullan, Idaho, is an outstanding example of a property in the Coeur d’Alene district where a small and insignificant- appearing silver-lead-zinc vein at the surface has changed at depth into a large vein of great importance. The Lucky Friday vein has little if any surface expression and above the 1200 level the ore shoots are small and discontinuous. Between the 1200 level and 2450 level, the lowest developed level, the main ore shoot has shown remarkable improvement on each succeeding lower level, and today the mine is one of the major lead-silver producers in the Coeur d'Alene district. History: The Lucky Friday property is on the north side of the South Fork of the Coeur d'Alene River in sections 25, 26 and 35, T. 48 N., R. 5 E., Hunter mining district, Shoshone County, Idaho. This is about one mile east of the town of Mullan, which serves the eastern portion of the Coeur d'Alene district. The southern part of the property is crossed by a branch line of the Northern Pacific Ry. and by U. S. Highway 10. This highway is the principal road crossing the panhandle of Idaho and connects the district with Spokane, Wash., on the west and Missoula, Mont., on the east. The main portal and surface plant of the Lucky Friday mine is at an elevation of 3365 ft, only a short distance above the valley floor and a few hundred feet from U. S. Highway 10, so the mine is readily accessible for year-round operation.

Jan 12, 1958

By K. Tanaka, J. D. Mote, J. E. Dorn

It) an attempt to ulLcoce.lP the operative strain-rate-contl-olliy: dislocation nieclzanistns, specially oviented sizgle clystals of the intel-nzediate 1zexagonal phase containing Ag plus 33 at. pct A1 were tested in tension over a wide range of temperatures. Slip was observed to take place by the {0001} <1120> {l100} mechani fracture took place across the(i100) plane and winning occurred by the (i01Z) ?lechanisn. Basal slip exhibited a strong yield point over the -alzge from 77 to 450°K, the upper ,esolved shear st]-ess having the exceptionally high value of 10,500 psi over this entire ?-a?zge of tenzpei,atuves. The critical 9-esolved shear stress for prismatic slip decreased f7-om 48,000 psi at 4.3"K to 23,000 psi at 170°K (Region 1) follozcirg zt:lzich it decl>eased sloz&ly to 21,500 psi at 475°K (Res&apos;on II); from 475" to 575°K (Regioz III), the c7-itical esolced shear stress dec&apos;-eased precipitously to 2000 psi; and from 575" to 750°K (Region IV) it decreased less afi&apos;dly to a low value of about 500 psi. Pvistintic slip in Region I was pobably controlled by the tliel-nally activated riecharzisui of nucleation and g,-ozcth of kinks in dislocations lying in Peierls potential troughs. In Region II for prismatic slip the critical 1-esolved shear stress was slzocn to be deteemined by sh0l.t-range 01-dering, Overall the forgiorz fo basal slip, 7.c.lre1-e a Strong yield-point phenorlienu ia7as observed, the critical vesolved slzea?-stress was shoztn to be determined by n conibirzation 0-f Szizuki locking and short-range-order Izavderzizg, The precipitous decrease in the critical resolved shear stress with increase in ter,/pe7-atrir-e over Region HI was tentatively ascribed to a decrease in the degree of slort-)ange 07-del;iqq (0)- clusteing) and also the effect of fluctuations the degree of o?der, It is at pgreser2t zrtzce)taitz as to 1t1hethe1- these or other possi1)le effects are also ,esponsible. fo- the data obsel-ved 172 Region IV. 1NTEREST in inter metallic compounds stems not only from their role in dispersion hardening of polyphase alloy ystems but equally from their potentialities for high strength, hardness, and stability not only at atmospheric temperatures but especially at elevated temperatures. As summarized in a re- cent symposium of the Electrochemical Society on "Mechanical Properties of Inter metallic Compound", most of the experimental evidence regarding the mechanical behavior of intermetallic compounds centers about the effect of temperature on the hardness and ductility of polycrystalline specimens. The available data reveal that the plastic behavior of intermetallic compounds might be rationalized in terms of the usual dislocation mechanisms appropriate to a solid solutions providing the additional complexities arising from crystal structure, long-range ordering, short-range ordering, and defect lattices are taken into consideration. It is apparent, however, in terms of the history on a solid solutions, that a complete detailed mechanistic rationalization of dislocation processes may not be possible until the deformation processes are studied in single crystals of intermetallic compounds. The present paper contains a preliminary report on the plastic behavior of single crystals of the hexagonal Ag-A1 intermetallic phase over a wide range of temperatures. The results confirm the thesis that single crystal data provide a most effective method of identifying operative dislocation mechanisms in intermetallic compounds. EXPERIMENTAL TECHNIQUES Several factors prompted the selection of the hexagonal Ag-A1 intermetallic phase for this preliminar investigation on the plastic properties of single crystals of intermetallic compounds: 1) This phase has a wide solubility range5 which would permit future investigations on the effect of composition and axial ratios on slip mechanisms. 2) Although it undoubtedly exhibits short-range ordering (or clustering) this intermetallic phase is free from complexities arising from long-range ordering.6 3) Since the atomic radii of aluminum and silver are practically identical, the possible complications due to Cottrell locking are minimized. 4)Whereas the dislocations on the basal planes are expected to dissociate into Shockley partials and are thus susceptible to Suzuki locking, those on the prismatic planes probably remain complete. 5) The axial ratio, being 1.61, is almost ideal, suggesting that short-range ordering may be almost spherically symmetrical. The present investigation was conducted exclusively with the hexagonal Ag-A1 alloy containing 33 at. pct Al. Preliminary investigations revealed that this alloy undergoes basal slip by the (0001)

Jan 1, 1962

By R. G. Schaal

The Magma Mine at Superior, Arizona had an unimpressive beginning as a. worked out silver mine that was purchased in 1910 for $130,000 and then incorporated into the Magma Copper Company which has been continuously mining the deposit since 1915. Copper is the principal metal produced. However, zinc, gold, silver and iron have also contributed to the total metal product. Prior to 1973, the production rate of 1500 tons per day was maintained by hoisting 4 and 5 ton pay-loads at speeds up to 1100 FPM through four small hoisting shafts. The hoists used included 8&apos; and 7&apos; diameter double drum, double clutched doc. and a.c. motor driven geared units built as early as 1917. One old timer that did yoeman&apos;s service for many years was an 8&apos; Bollen Pulley with a.c. geared drive that utilized an endless rope system with mechanical grip and release mechanism built into the pulley&apos;s throat. Primary power for all of these old production hoists was 25 Hertz. Exploration that was completed in 1967 developed a reserve of 10 Million tons of 5 per cent copper which was sufficient to justify new capital expenditures for enlargement of productive facilities to 3300 tons per day. To reach the new reserves a 22&apos; I.D. concrete lined vertical shaft was sunk to an initial depth of 48431. A 12 ½ diameter adit was bored from the mill side of the mountain to intercept the shaft at a point about 1100&apos; below the collar. This 9200&apos; long adit provides the right-of-way for the mine to mill railway and egress for heavy supplies from rail head as well as a conduit for potable water, electric power, compressed air and mine drainage. Mine operating levels begin 3582&apos; below collar and thereafter have been cut at 100&apos; vertical intervals. Skip loading stations have been installed 4282&apos; and 46821 below collar with an in-shaft skip dump station located 800&apos; below collar. This provides for 4500 tons of storage above the mine to mill train loading station located 1100&apos; below collar. Ore and waste are moved horizontally from stope chutes and drift headings by rail haulage to transfer raises which channel all material to the two mentioned skip loading stations. The 22&apos; diameter shaft crossection is arranged with the two skip compartments on the south side separated from the manway and utility compartments by the cage compartment. The cage counterweight operates in a portion of the southwest quadrant of the shaft. The hoisting plant consists of two conventional Nordberg double drum, single clutch, geared, d.c. motor driven units that are identical except for the drives and automatic controls. The drums are 15&apos; diameter x 105" face with LeBus grooving for 2-1/8" diameter wire rope wound in three layers. Mechanical design emp1o::ed is the same as has been used for the past twenty- five years. One drum is attached to the main shaft by 2 large bolted integral shaft flenge. The loose drum is engaged by a 4-arm positive tooth clutch meshing with radially cut teeth of the clutch ring which is bolted to the drum. The drums are one-piece steel plate weldments having a finished weight of 60 tons each and are mounted upon a 36" diameter shaft that also weighs 60 tons. With the addition of brake rings, clutch, bull gear and rope, the total dead weight adds up to nearly 250 tons that is supported by just three double row spherical roller pillow block bearings. There is no bearing between the drums. All pinion shafts as veil as all head sheave journals are supported in the same type of antifriction bearings.

Jan 1, 1975

D. F. HEWETT, Washington, D. C. (communication to the Secretary*).-I am not prepared to discuss the metallurgical use of manganese in the form of alloys. In connection with other work for the U. S. Geological Survey, however, I have been investigating incidentally, for about 5 years, the American as well as other sources of manganese. There are some conclusions that come out of this investigation that may interest those whose greatest interest lies in the use of the alloys. From a geological point of view, most manganese ore deposits may be regarded as concentrated masses of manganese oxides, as there are few masses of the other manganese minerals that are rich enough in manganese and low enough in silica to warrant smelting. The deposits of the Huelva district, in Spain, which are largely manganese carbonate and silicate, are exceptions to this statement. Some deposits of manganese oxides, such as those of Russia and Cuba, are bedded with ancient sediments, and although they are clearly concentrated under unique conditions, the source of the manganese cannot be determined. Probably 60 per cent. of the world&apos;s production of manganese ore, or 95 per cent., if that of Russia be excluded, is derived from the superficial parts of deposits that have undergone weathering and enrichment near the surface. In other words, the situation with the manganese ore supply is such as it would be with regard to copper, if instead of being derived largely from deep zones of deposits of deep-seated origin, such as veins, it were derived solely from the zone of secondary enrichment. Manganese oxide occurs in all rocks but is most abundant in igneous rocks, of which, according to Clarke, it forms an average of 0.10 per cent. It also forms 0.05 per cent, of the average limestone, but only traces are present in shales and sandstones. It is interesting that although many commercially important manganese deposits occur in rocks that are but slightly richer in manganese than the average, the most important deposits occur in rocks of unusual character that are much richer in manganese than the average. Thus, the most important deposits of India and Brazil overlie or occur near masses of rocks that contain excessive amounts of manganese garnet and pyroxene.

Jan 5, 1917

By M. M. Wong, D. E. Couch, G. M. Martinez

The Bureau of Mines electrowon hafnium metal with an average oxygen content of&apos; 150 ppm at 700°C from an electrolyte containing 27 wt pct LiCl, 62 wt pct RbCl, and 11 wt pct HfC14. The average anode and cathode current efficiencies were 90 pct at anode and initial cathode current densities of 86 amp per sq ft. Haf-nium metal with an average oxygen content of 440 ppm was electrowon at 800oC from an electrolyte containing 90 wt pct KC1 and 10 wt pct HfCl4. The average anode and cathode current efficiencies were similar to those obtained in the LiCL-RbCl-HfCl, electrolyte. The chlorine gas given off at the graphite anode was vented through either a silica or a graphite tube to prevent cell corrosion. THE current method for the commercial production of high-purity hafnium is the thermal decomposition of Hfl4.1 The iodide method is not adaptable to continuous process techniques. Nettle, Hiegel, and Baker2 studied the electrorefining of hafnium from hafnium sponge containing 800 ppm oxygen. They failed to obtain hafnium with 600 ppm oxygen in their initial deposits and obtained AEC specification for oxygen only after 75 pct of the soluble hafnium had been removed from the electrolyte. Calculations using their data indicated this was approximately 4 lb of hafnium. The electrolyte was then used to produce approximately 3 lb of hafnium with a low oxygen content. However, no data are shown concerning the amount of anode material initially used or what percent of it was dissolved, therefore, results are not suitable for evaluation of a continuous operation. In general, it was not possible to consistently obtain low oxygen content metal with the electrolytes described by Nettle, Hiegel, and Baker. Wong, Hiegel, and Martinez3 investigated the electrorefining process for hafnium and showed that even by strict control of electrolyte composition only relatively low oxygen reduction could be obtained. The oxygen contained in the hafnium anode material tended to transfer to the cathode deposit and only a limited purification was possible. Both the "iodide" and the "electrorefining" processes depend upon hafnium sponge as a starting material. The sponge is normally produced by magnesium reduction of HfC14 &apos; and does not meet AEC specifications for hafnium metal. Since only 30 pct of the anode feed could be utilized3 in the electrorefining cells, the Bureau of Mines developed an electrowinning process. HfC14 was used as the feed material for the electro-winning process described in this report. Many of the electrolytes used in the electrorefining studies3 ap- peared to be suitable carrier-electrolytes for HfC14. However, in the initial studies on electrowinning, it was desirable to use electrolytes that had low solidus temperatures and could be operated over a wide temperature range to investigate parameters of the process. Therefore, electrolytes containing LiC1, NaC1, KC1, RbC1, CsC1, and HfC14, in various combinations were explored. EQUIPMENT Chlorinator. Hafnium carbide was chlorinated to produce HfC14 in the batch-type chlorination shown in Fig. 1. Chlorination temperatures were measured with a thermocouple placed in the center of the HfC charge. A flow meter was used to monitor the helium and chlorine. The exhaust side of the silica chlorina-tor tube was equipped with a flask for collecting organic material released during the initial heating of the HfC. The temperature of an internal heater, which extended from the HfC14 condensing flask to the hot end of the chlorinator, was adjusted to prevent the HfC14 from condensing before entering the collection flask. Helium and excess chlorine were exhausted through the lid of the collection flask to an aqueous NaOH solution. Sublimer. Initial studies were conducted using a sublimer, Fig. 2, made by placing a 13/8-in. OD nickel thimble 11 in. long, inside a 11/2-in. ID nickel bell 12 in. long, and locking it in place. This unit was loaded with HfC14 and partially immersed in the molten electrolyte for sublimation directly into the electrolyte. In another sublimer shown in Fig. 3, the HfC14 was contained in a "resin reaction flask". Quartz wool, previously heated to 600aC, secured between two nickel wire screens, was placed just above the HfC14 powder. The lid contained a vacuum outlet, a gage, an argon inlet, and an air-cooled pipe for condensing the HfC14. This sublimer was evacuated and heated. The sublimation temperature was not critical and the sublimer operated satisfactorily at all temperatures between 250" and 350°C. Electrolytic Cell. The electrolyte chamber, Fig. 4, was made of mild steel 8-in. schedule 20 pipe, 30 in. long. The exterior was metallized with a Ni-Cr alloy. The electrolytes were contained in a 16 gage nickel or iron liner with a nickel heat shield on top. The cell was heated by a resistance furnace. A 21/2-in. ID by 25 in. long air lock was connected to one port of a two-port cell cover assembly through a slide valve. The cover assembly of the air lock was electrically insulated from the cell and was equipped with a rubber sleeve that provided for the passage of the cathode lead. This allowed the cathode deposits to be removed and a new nickel cathode to be introduced without allowing air to enter the cell. A tube-rod assembly was bolted to the other port on the cell cover assembly and was sealed by a packing seal. The tube-rod assembly consists of a graphite

Jan 1, 1970

By B. C. Allen

The interface energies of chronzium, molybdenunz. hugsten, and their solid-solution alloys Cv-35Re, MO-33Re, and UJ-25Re were studied at 0.6 to 1.0 of the absolllte liquidus ter)zpe,vature using fiz&apos;e )izethods. Liquid surface tension, yv , was deter mined clsing the pendant-drop and drop-weight methods. Results are, respectizlely, 1700, 2370, and 2480 +100 dynes per ct for the rhernium -containing alloys and essentially the same as tlwse reported for liquid chro)riln, trolybdenum, and tungsten. Average solid slrjace energy, rsv< xias ))zeasured using tlre fiber-extetlsion method. The ratio of ysS, the acerage high-angle grain-boundary energy, to ySV cclas jolnd fronz grain-bolzdary grooue angles fort)zed at the surface in an inert atrfizosphere. Absolllte iute?:face energies were deterawined using ?nultip/rase equilibria involzing suitable liquids of known surface tension (tin, silver). Interpretation of the experimented results in view of pvobable tenzperatzcre, orientation, and purity effects giz,e the follouling approximations in ergs per sq ctn: ysv (i2lo. Mo-33Re) - 2100, ySS (Mo, Mo-33Re) - 800, rr (defornzation twins in MO-33Re at 1200"C) - 800. ysV (Cr. Cr-35Re) - 2400. YSS (CY, Cr-35Re) - 1000. Probably Ylv- YSV- 2500 for tungsten and W-25Re, giving yss (It&apos;, W-25Re) - 900. The interface energies of solid and liqid ch?&apos;omiu?.z, nolybdenu?rr, and tungsten are not geatly aff&apos;ected by rhenium and therefore are not a ttlajor factor in the ductili zing rhenium effect in Croup VI-A metals. THE interface energies of the refractory Group VI-A metals, chromium, molybdenum, and tungsten, are not well-established. The objective of this investigation was to study the liquid surface tension, solid surface energy, and grain-boundary energy of these metals and compare them to those found for the bcc solid-solution alloys, Cr-35e,&apos; 0-33e,&apos; and -25e. Five techniques were used to measure interface energies in high-purity polycrystal rod, wire, and sheet at 0.6 to 1.0 of the absolute liquidus temperature. The alloys were chosen to see if there was any connection between interface-energy behavior and the ductilizing rhenium effecL4j5 EXPERIMENTAL WORK Materials. A description of the materials used is presented in Table I. Chromium rod was prepared by arc melting iodide process crystals supplied by Chromallo Cor., hot extruding, and warm swaging to 0.63-cm-diam rod.6 The sheet was prepared by rolling as-extruded rod to 95 pct reduction in area from a hydrogen furnace at 800" to 900°C and surface grinding off 0.02 cm from each face. Cr-35Re rod was prepared by arc melting sintered rhenium powder and iodide chromium crystals, warm rod rolling to 50 pct reduction in area in cans, and swaging to 60 pct reduction in area at 1100" to 1200°C. Some of the rod was warm-rolled to sheet and then surface-ground. Portions of swaged chromium and Cr-35Re were further reduced by swaging and drawing to 0.013-cm-diam wire by the General Electric Co. Mo-33Re and W-25Re rod, sheet, and wire were provided by Chase Brass and Copper Co. The molybdenum sheet consisted of two lots, both essentially the same except for the carbon content. Liquid Surface Tension. The liquid surface tension of Cr-35Re, Mo-33Re, and W-25Re was measured by a combination of pendant-drop and drop-weight methods using techniques already decribed." Following out-gassing, molten drops were formed on the ends of centerless-ground Mo-33Re and W-25Re rods by electron bombardment at 5 x 106 mm. Similar drops were formed on outgassed Cr-35Re rods by induction heating under 1 atm of 99.995 pct Ar. Solid Surface Energy. Solid surface energy was measured by conducting microcreep experiments on molybdenum, Mo-33Re, chromium, and Cr-35Re wires at 2350°, 2306, 1550°, and 180O°C, respectively. In preparation, gage marks -2.5 cm apart and -0.001 cm deep were circumferentially scribed on the wire with a razor blade. Weights of the wire material were then attached. Five to seven reasonably straight wires were hung in a container made out of the wire material. The free end was placed through a small hole in the removable top and secured by bending a small portion 90 deg. The containers not only tended to provide vapor-solid equilibrium for the wires but also protected them from gaseous impurities. They were nominally 2.5 cm in diam by 5 cm high and were made from extruded chromium rod, Cr-35Re arc casting, molybdenum bar stock, or welded Mo-33Re sheet. After deg re as ing, the assembly was outgassed at a relatively low temperature to 2 x 10"5 mm and then recrystallized 2 to 8 hr at the creep temperature in a rhenium-element resistance furnace. The static argon atmosphere was gettered by tantalum radiation shielding. Specimen temperature was measured optically to 25"C using calibration with known melting points and blackbody conditions. The wires generally developed a stable bamboo-type structure according to Fig, l(b), (c), and (d) and retained their gage marks [upper portion of Fig. l(d)]. One or two of the weights were clipped off to provide a low load for the creep anneal. To minimize the possibility of bending or breakage, the wires remained attached to the top of the annealing container which was held to keep the wires vertical. The distance between gage marks was

Jan 1, 1967

By R. M. Daelen

Mechanical science is severely tested by the demands of the iron manufacture for the varied apparatus needed to transport and to treat raw materials and products. Water has long been a favorite means of transmitting pressure for such purposes, because of its own incompressibility. Further advances in its use are the more to be expected, since mechanical improvements have steadily tended to overcome the difficulties formerly encountered in the employment of great hydraulic pressures. So long as the pressure is not higher than that which requires for plungers, etc., only ordinary stuffing-boxes, with hemp or other similar packing, the necessary arrangements for the production and transmission of the water-pressure without leakage are very simple. But when this limit (which is, for most purposes, 50 kilos to the square centimeter) is exceeded, new conditions of construction arise, which are met in various ways, and which justify a primary division of hydraulic presses into low-pressure and high-pressure respectively. The former are used in lifting and moving weights, and employ pressures as high (in extreme cases) as 100 kilos per square centimeter; but at this point the friction between piston and hemp-packing is so great that the use of cup-leathers is already preferable. Beyond 100 kilos it becomes a necessity. The range of practicable tight packing which follows is considerable, extending to about 1000 kilos; but "high pressure" in practice is from 100 to 600 kilos, and it is to this that the present paper applies. General Classes and Types. Hydraulic transmission at high pressure usually claims consideration in case the solid mechanism, such as levers, cams, screws, and gear-wheels, would have to be too large, would involve too much friction, or could not be suitably adapted to the speed-requirements of the working-tools. Since steam is mostly the primary carrier of

Jan 1, 1893

By KENNETH CITTISGHAM

During the year 1945, the total number of wells drilled in Ohio, including the. non¬productive wells, was 1034. For the 10-year period ending with 1945, the average completions per year were 1125, the least number being 910 in 1938, and the maximum 1561 in 1941. The proportion of dry holes in 1945 was 37 per cent?about the same as for the year 1944 but exceeding the 10-year average, which was 34 per cent. The number of oil wells completed exceeded the number drilled in 1944 by about 30 per cent, the average initial per well being the same in both years. Gas-well completions were approximately 10 per Cent less than in 1944, with the average initial per well about 5 per cent greater. The difference in number of oil and gas wells in the two years was in Berea and Clinton completions, as the number of oil wells increased about 30 per cent, owing to greater activity in the two sands named, while the number of gas wells decreased because of fewer completions therein.

Jan 1, 1946

By M. E. Straumanis, S. M. Riad

The lattice parameter of 99.999 pct pure Ag rtlas redetevnzined and found to be az5 = 4.08626 5 0.000041 with the vefnzctiotz correction included); the expatzsion coejjicient between 10° and 65°C was 18.73 X10-6°C-1. The lattice paratneter increased upon solution indium in silver in good agrement with other authors. The solid-solubility limit around room temperature was at 20.4 wt pct of in, which suggests that the high-temperature solubility (at about 689°C) determined by other authors is too low. The expansion coejficient of si1ver increases with the itzcrease of indium content between 10° and 65° C from, 18.73 (In = 0) to 20.9 x 10-6°C-1 (In = 20.4 pct), being only very slightly influenced by small amounts of indium. The expansion coefficents of all solid solutions increarsed strongly with temperature, reaching values > 27 x 10- 6 800°C. ACCORDING to the Ag-In diagram,&apos; the solubility of indium in silver (the a phase) extends to about 18 pct by weight at room temperature. However, there has been only one investigation of the solubility limit by X-ray methods—that of Weibke and Eggers.2 Hume-Rothery, Lewin, and Reynolds measured only the lattice parameters of Ag-In solid solutions3 as did Owen and Roberts4 and Adler and Wagner.&apos; The thermal expansivity of four solid solutions was determined by Owen and Roberts4 in a temperature range between 25" and 300°C. In view of the limited amount of work on Ag-In solid solutions, it seemed appropriate to redeter-mine the lattice parameters and the room-temperature solid-solubility limit, to find the exact expansion coefficients of the solid solutions at about room temperature (between 10° and 60°C) and the expansivity up to 800°C, and finally to derive the thermal-expansion coefficients for any alloy within the solid-solubility region. THE ALLOYS AND THE DETERMINATION OF LATTICE CONSTANTS The metals used were 99.9991 pet pure, supplied by the ASARCO company. Both silver and indium were weighed accurately on an analytical balance in

Jan 1, 1965

By W. C. Phalen

INTRODUCTION NOBODY will dispute the fact that the conservation in every legitimate manner of our valuable high-grade phosphate-rock deposits is a present-day problem of importance. The table and curve, given herewith, show. that during the past 10 years the exportation of high-grade rock has averaged very close to half the total output of the entire country. The bulk of this exportation is from Florida, for obvious reasons. It is plain that the deposits in this State, more particularly, are being wastefully depleted under a system of selecting the cream of the product for exportation to Europe, leaving the comparatively low-grade rock, running from 65 to 70 per cent., and under, in bone phosphate of lime, for our own n fertilizer manufacturers to work up when all the best rock is gone. In this paper the writer has endeavored to make a point of describing in some detail the important methods of production and conservation in Tennessee. These ought to prove of educational value to our American agriculturists and fertilizer manufacturers, and should result in a demand for the highest-grade rock, both for direct application to the soil and for use in making acid phosphate. It is certainly evident that the European

Jan 10, 1916

By E. H. Rennhack

Phase equilibria of the zinc-rich portion of the Zn-Fe-A1 system containing up to 20.0 wt pct Fe and Al have been investigated at 600°C (1112°F), 450°C (842°F), and room temperature by metallographic and X-ray diffraction techniques. The phase relationships were found to involve only those phases present in the three binary systems. THE presence of small quantities of aluminum (approx. 0.2 wt pct*) in zinc galvanizing baths is known to suppress the formation of Zn-Fe alloy layers within the coating.&apos; As part of an extended investigation of this suppression effect and the alloy reactions involved, the zinc-rich corner of the Zn-Fe-A1 equilibrium system containing up to 20.0 pct Fe and Al was determined at 600°C (1112°F), 450° F (842° F), and room temperature. The present paper reports the findings of this study. The constitution of the Zn-Fe system has been reported by Raynor2 based mainly on the work of Schramm3-3 and Truesdale et a1.6 The solid solubility of iron in zinc is extremely small and lies between 0.0009 and 0.0028 pct in the range 150° to 400°C (302°to752°F). Within the temperature and composition range of interest, a eutectic reaction involving nearly pure zinc, liquid = Zn+FeZn13, is observed at about 419°C (786° F) and 0.018 pct Fe along with a peritectic reaction, FeZn7+ liquid e FeZn13, at 530°C (986° F) and 6.2 pct Fe. The latter reaction is sluggish due to the large proportipn of solid phase involved in the transformation. Halla et al.,7 identified the compound FeZn13 as monoclinic with a = 13.68, b = 7.63, c = 5.07, and B = 128°44&apos;. The structure of FeZn7 was reported by Bablik, et al.,8 to be of hexagonal symmetry, belonging to either the C6v = C6/m mc or D46h = C6/mc space group. Divensions of the unit cell are a = 12.81A and c = 57.6a. The Zn-A1 diagram as composed by Raynor9 and later Gebhardt10 is characterized by a eutectic decomposition, liquid 382°C (720°F) and 95.0 pct Zn and a eutectoid decomposition, at 275° (527°F) and 78.0 pct Zn. The eutectoid reaction cannot be suppressed permanently by quenching. Above 275° (527° F), a and a&apos; co-exist in a closed miscibility gap between 31.6 and 78.0 pct Zn. Both phases are fcc and have nearly the same lattice parameter. The maximum solubility of aluminum in zinc (B) is approximately 1.0 pct at the eutectic temperature. PROCEDURE Materials. The experimental alloys were prepared from both massive and powdered material. Cast alloys were composed from three zinc-base master alloys containing 8.0 pct Fe, 16.0 pct Fe, and 50.0 pct Al which were made from C.P. zinc, Armco iron, and

Jan 1, 1962

By T. J. Whalen, S. M. Kaufman

Surface-tension measurements for liquid Fe-C-Co and Fe-C-Ni alloys were performed by the sesszle-drop technique at 1350o and 1425°C. Cobalt was shown to he more effective than nickel in lowering the surface tension of Fe-C alloys A minimum value for surface tension of 1640 dynes per cm was found in the Fe-C-Co system at a concentration of 1.5 pet C and 12pet Co. Analysis of these measurements in terms of adsorption and desorption behavior indicated that cobalt and nickel lower surface tension in Fe-C alloys by replacing carbon at the liquid-vapor interface. Comparison of results to date for Fe-C liquid alloys has shown that most substitutional-type elements having about the same atomic diameter as iron also have relatively the same influence on surface tension when present in dilute amounts. It has been shown previously that surface-adsorption behavior in liquid Fe-C ternary alloys is related to the manner in which the ternary addition affects the activity of carbon in the bulk solution.&apos; Certain ternary additions, such as chromium, tending to decrease carbon activity cause adsorption of carbon and chromium to the liquid-vapor interface. Additions, such as silicon, increase the carbon activity, resulting in a desorption of carbon and an adsorption of silicon. Both cases were shown to cause a decrease in surface tension due to adsorption. It is the object of this paper, as part of the writers&apos; continuing interest in the effect of alloying additions on the surface tension of Fe-C alloys, to present and discuss surface-tension data on solutions in the ternary systems Fe-C-Co and Fe-C-Ni. Available activity measurements for these systems in the solid state indicate a strong increase in carbon activity when either nickel or cobalt is added to Fe-C alloys.2, 3 EXPERIMENTAL PROCEDURE The alloy compositions used are shown in Table I. These alloys were prepared by vacuum melting in stabilized zirconia crucibles and then vacuum casting into cold-steel molds. The nominal analyses for the alloys used in this investigation are given in Table I. Surface tensions and densities were measured by the sessile-drop method4,5 in conjunction with the tables of Bashforth and bdams.&apos; Specimens were prepared by slicing 1/4-in. cubes from the center of the vacuum-cast ingots and grinding the edges of these cubes until their shapes approximated spheres with flat bottoms. Proper handling techniques, including an acetone rinse immediately before use, assured minimum contamination from sources extraneous to the actual melting. For each experimental run a sample was placed on a BeO plaque and positioned and leveled inside a vacuum induction heating apparatus. The sample and plaque arrangement sat inside a molybdenum tube which acted as the susceptor. Diagrams of this apparatus may be found in the literature.= After heating to temperatures just above the liquidus at pressures of the order of 10-4 to 10- 5 mm Hg, photographs of the drop profile were made using its natural thermal radiation as a light source. Some measurements were made with partial pressures (-1 cm Hg) of a mixture of H2 and He gases. The H2-He atmospheres proved to be necessary at higher nickel contents to retard excessive vaporization losses. Chemical analysis for carbon and the ternary addition was performed for each alloy sample after completion of the experimental run.

Jan 1, 1964

By G. L. Fisher, R. H. Geils

The effect of small amounts of columbium (<0.01 to 0.10 pct) on the ?-a transformation occurring during the continuous cooling of a low carbon Ni-Cu steel was investigated. Dilatometer specimens were aus-tenitized at 950" and 1068?C and cooled at 17? and 375 C° per min. Columbium caused a marked depression in the ?-a transformation temperature except when cooling at the slower rate from 950°C. The effec of columbium on the transformation temperature was greater the higher the austenitizing temperature and rate of cooling. A maximum depression of 92 C" was observed. Metallographic examination of specimens of <0.01 and 0.07pct Cb steels heated at 1200°C for 1 hr and cooled at various rates showed that columbium had a major effect on the ferrite morphology. The fer rite in the columbium -free steel remained equiaxed at cooling rates as high as 440 C? per min while the columbium-bearing steel exhibited mixed structures o equiaxed and bainitic ferrite at cooling rates as low as 130 C° per min. The ? grain boundaries in the columbium -free steel provided the ferrite nucleation sites in rapidly cooled specimens. There was a complete absence of nucleation at these sites in the colum bium-bearing steel. It is concluded that columbium depresses the transformation temperature by suppressing ferrite nucleation at the austenite grain bound-aries. In this respect the effects of columbium are analogous to those of boron in low C-Mo steels. It is well known that small columbium additions can substantially strengthen plain carbon steels. As little as 0.02 pct Cb can increase the yield strength of mild steels by 10,000 psi.1 A fine precipitate of CbC has been observed in columbium-bearing steels2 and is generally thought to be responsible for the strengthening. Little attention has been devoted to the effect of columbium on the ?-a transformation. Webster and woodhead3 have studied the effect of columbium on the isothermal proeutectoid ferrite reaction in mild steels. They found similar transformation behavior in steels both with and without columbium additions. However, as the austenitizing temperature increased, the incubation time for the start of the ferrite transformation became longer in the columbium-containing steel. Morrison1 found that the addition of 0.03 pct Cb to a C-Mn steel lowered the transformation temperature by 50 C° during cooling from 1200°C at a rate of 80 C" per min. The strengthening effect of columbium has recently been utilized in an age-hardenable, low-alloy steel containing copper and nickel.4 A small amount of columbium has a substantial effect on the as-rolled strength of this steel. By increasing the columbium level from <0.01 to 0.13 pct the as-rolled yield strength is increased by 15,000 psi. Columbium also significantly lowers the ?-to-a transformation temperature of this steel during continuous cooling from the austenitizing temperature. Because of the low carbon level in this steel (0.05 pct max), it is almost entirely ferritic. Thus, it offers the opportunity of studying the effect of small columbium additions on the proeutectoid ferrite reaction. Of particular interest in this study was the reason for the marked lowering of the transformation temperature by columbium during continuous cooling. EXPERIMENTAL PROCEDURE Materials. The compositions of the steels used in this investigation are shown in Table I. The steels were 30-lb air induction melts. They were forged to 4 by 8 by 1 in. plate at 1230°C, air cooled, and then reheated to 1230°C and cross-rolled in two passes to in. plates. Dilatometry. A Leitz Bollenrath dilatometer was used to record the transformation during continuous cooling from two different austenitizing temperatures. The dilatometer specimens were + in. in diam and 2 in. long. Oxidation and decarburization of the specimens was prevented by maintaining a small positive pressure of dry argon in the dilatometer furnace and by plating the specimens with 1 mil of Cu. For the lowest cooling rate, 17 C" per min, the temperature of the specimen was measured with a Pt-Pt 10 pct Rh thermocouple placed in a & in. diam well in the center of the specimen. During air cooling, 375 C° per min, this method of measuring the temperature interfered with the operation of the dilatometer. However, it was found that the temperature of the specimen could be measured accurately by placing a thermocouple in an identical specimen in a holder adjacent to the one being used to operate the dilatometer mechanism. The dilation-temperature curves were recorded on photographic film and then converted to volume percent ferrite-vs-temper-ature curves. The cooling rates obtained with the dilatometer are shown in Table 11. Cooling rates of

Jan 1, 1970