Search Documents

By H. D. Kessler, R. J. Van Thyne

Phase diagrams of the titanium-rich portion of the ternary systems from 0 to 10 wt pct Al and 0 to 1 wt pct 0, N, and C were determined. Micrographic analysis of annealed high purity arc melted alloys was the principal method of investigation and was supplemented by X-ray diffraction. TITANIUM-ALUMINUM alloys exhibit excellent properties, particularly for elevated temperature use. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the effect of the interstitially soluble contaminants, oxygen! nitrogen, and carbon, on the Ti-A1 system. Using high purity arc melted alloys and micrographic analysis of annealed samples as the chief method of investigation, titanium-rich partial phase diagrams were determined for the ternary systems. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9+ pct pure) produced by the New Jersey Zinc Co. and Foote Mineral Co. The aluminum was obtained from the Aluminum Co. of America in the form of sheet. The given analysis was: Si, 0.0006 pct; Fe, 0.0005; Cu, 0.0022; Mg, 0.0003; Ca, <0.0006; Na, <0.0005; and Al, 99.99. High purity titanium dioxide purchased from the National Lead Co. was used in the preparation of the oxygen-bearing alloys. The spectrographic analysis of this material was as follows: SiO,, 0.07 pct; Fe,O,,, 0.002; A1,0,, <0.001; Sb,O,, <0.002; SnO,,, <0.001; Mg, <::0.001; Cb, <0.01; Cu, 0.0004; Pb, 0.002; Mn, <0.00005; W, <0.01; V, <0.002; Cr, <0.002; Ni, <0.001; and Mo, <0.002. Special spectroscopic graphite rod purchased from the National Carbon Co. was used in the preparation of the Ti-A1-C alloys. Alloy Preparation: Alloy ingots weighing 10 grams were melted in a nonconsumable tungsten electrode arc melting furnace using water-cooled copper hearths and a helium atmosphere. The arc was struck on a tungsten stud in the copper block to minimize contamination from the electrode. Details of the techniques have been reported.&apos;, &apos; Each ingot was inverted and remelted a minimum of four times to insure homogeneity, without opening the furnace. Remelting small control ingots of iodide titanium under similar conditions resulted in no measurable hardness increase, indicating contamination-free melting conditions were used. The alloy charges and resultant ingots were weighed to the nearest milligram. Only small weight losses were obtained upon melting, indicating that the actual compositions were very close to the nominal compositions. Check analyses substantiated this. Oxygen and nitrogen were added during ingot preparation as master alloys. An oxygen master alloy containing 25 wt pct 0 was prepared by melting iodide titanium and pressed titanium dioxide (40 pct 0) powder. The Ti-25 pct 0 alloy is more easily handled during weighing and charging than the pressed TiO, powder. Chemical analysis indicated that titanium-nitride received from an outside source contained large amounts of impurities (2.7 pct Ca). Therefore, a master alloy containing approximately 12 pct N was prepared by melting nitrided sponge titanium. As the sponge melted with difficulty, the alloy was diluted by addition of titanium to lower the melting point. The chemical analysis of the final alloy was 6.69 pct N. Both master alloys are friable and were used as —8 +16 mesh lumps resulting from crushing the ingots. NIelting the Ti-A1-0 and Ti-A1-N compositions five times produced homogeneous ingots. The preparation of homogeneous carbon-bearing alloys caused considerable difficulty. Alloys containing less than 1 pct C were prepared using spectrographic graphite rod, 1/8 in. diameter by 1/8 in. long. However, the graphite did not dissolve even with long melting times and many remelts. The ?/s in. pieces of graphite were used rather than powder because the low density powder is troublesome in arc melting.

Jan 1, 1955

ALABAMA Anniston.-Bretz, J A Carnngton, F G Gerber, A B Ashland -Barton J Sturdevant, J C Bessemer -Abbott, C E Ball, T L Ferguson, V Salmon, H S Schaber, C F Thompson, N E Whatley, W J Birmingham.-Adams, J H -Aldrich, T H Aldrich, T H , Jr ALASKA Anchorage -Dyer, B W. Parker, H C Smith, S S Chichagof.-Baumann, H N , Jr Copper River.-Douglass, W C Cordova.-Hazelet, G C Fairbanks -Davis, J A Hyder -Pitt, D L Juneau -Jackson, G. T Murphy, R E R..11 ti At i

Jan 1, 1923

By David W. Brunton

Mine-drainage and the ever-increasing demand for water on the plains have within the past few years necessitated the driving of a great number of adits and tunnels, including many of considerable size and great length. In most instances, existing conditions have called for extreme rapidity of execution; and this necessity, coupled with the high altitudes at which most of the work has been carried on, excessive freight-rates, and difficulty of access, has involved many complex and interesting problems. One of the most rapidly executed undertakings of this class is the Laramie tunnel, recently completed for the Laramie-Poudre Reservoirs & Irrigation Co. This tunnel is driven through Green ridge, a spur of the Continental Divide, which separates the Laramie river from the Cache-la-Poudre in Laramie county, Colo. Green ridge is extremely persistent, and further northward in Wyoming is known as Sherman hill, the highest point on the Union Pacific railway. At the point where the tunnel is driven, two opposing bends bring these streams within 2.5 miles of each other, with a difference in elevation of 500 ft. The rock exposed on the banks of the two rivers does not differ materially in hardness; and, without a geological study of the conditions involved, it would appear that the difference in the depth of erosion of the two streams is due principally to the greater volume of water at this point in the Cache-la-Poudre, which has a drainage-area above the tunnel-portal of 110 sq. miles, as against 30 sq. miles of natural drainage for the Laramie. To increase the water-supply at the tunnel, however, this latter amount has been augmented by two side collection-canals, which bring the available drainage-area up to 84 square miles. The nearest railroad shipping-point to the eastern portal is

Jan 1, 1913

By Francis P. Sinn

LOW prices have made 1938 a difficult year for the zinc industry of the world. Particularly in the United States, output had to be radically curtailed to bring production into line with consumption. Despite these unfavorable conditions, some additional plant construction is contemplated. In Jugoslavia, through co-operation with the Government, Trepca Mines is lo build a zinc plant to produce 10,000 metric tons annually, the plant to be ready for operation in July, 1941). Cerro de Pasco is proceeding with its plans for an electrolytic plant in Peru. A pilot plant, to be ready next summer, is under construction. In eastern Canada an electrolytic plant is planned in Quebec to treat concentrates from Yoranda and other mines but no defi-

Jan 1, 1939

By W. C. PAGE

ALL mine ore here must be concentrated before shipment, which involves selective flotation. Three products are made: lead, zinc, and pyrite concentrates. The equipment and practice are so well outlined in the accompanying flow sheet that only a few amplifying remarks are necessary. After crushing at the mine to approximately 4 in., the ore is carried by aerial tram about 4 1/2, mi. to the mill. From 1800 to 2000 metric tons per day, excluding Sundays, is thus transported. At the mill, the buckets are hand-tipped into the bins. After crushing to pass a ¼ -in. square opening, the ore may be stored in reserve crushed-ore bins or ball-mill feed bins as desired. Total bin capacity at the mill is about 4000 metric tons. The concentrator is arranged in three independent grinding sections, each fed from its own storage bin. Grinding operations follow standard practice, with ball mills in single-stage closed circuit with classifiers, the overflow from which is delivered to the lead circuit rougher flotation machines,

Jan 1, 1936

By E. T. Turkdogan

This is a compilation and a critical review of the data on the Fe-Ca-0 ternary system. Using the results on the reductiorz-equilibria, an oxygen potential diagram is drawn for the greater part of the system. A number of univariant systems and invariant points, not determined experimentally, are evaluated by making use of the theorem on univariant curves intersecting at an invariant point. The formation of solid solutions and ternary compounds and the crystal structures of some of the phases in the composition-diagram are given for a feu! temperatures. DURING the past thirty years there has been a continued interest in the study of the Fe-Ca-0 system. A detailed literature survey made by white1 in 1943 indicated that further work was required to clarify the phase relationships; in fact, the work carried out in the subsequent years, reviewed by Burdese2 in 1954, made a valuable contribution to a better understanding of this subject. Most of the data were obtained by the step-wise reduction of mixtures of iron oxides and calcium ferrites. However, there is some uncertainty about the phase relationships in this system, arising mainly from insufficient use of thermodynamic concepts in the construction of phase diagrams. In this paper an attempt is made to establish the invariant points from the available data. OXYGEN POTENTIAL DIAGRAM Schenck and coworkers3,4 were the early investigators who studied part of this system by the step- wise reduction method and suggested the formation of two ternary compounds, CaO.FeO.Fe2O3 and 2Ca0.5Fe0.2Fez03, the latter being referred to as point X. They also deduced from their results that the phases Y (8.74Ca0.32.5Fe0.8.74Fe2O3 and Z (2.02CaO-97.98FeO) were formed near the w?stite corner of the system. Martin and voge15 postulated the existence of the compounds CaO.9FeO and 4Ca0.3Fe3O4; the former is very close to the composition of point Z and the latter to that of CaO.FeO-Fe2O3. The most valuable contribution to the presen knowledge on this system was made by Cirilli and Burdese6-8 who showed by X-ray and chemical anal yses that there were two ternary compounds, CaO-Fe0.Fe2O3 and CaO.3FeO-FezO3; the former is the same as that suggested by Schenck et al. and the latter is close to their point X. The results of Cirilli and Burdese show that the phases Y and Z postulated by Schenk et al. are solid solutions of calcium oxide in w?stite. In most of the above-mentioned reduction-equilibria measurements carbon monoxide-carbon dioxide mixtures were used and in a few cases hydrogen-water vapor mixtures were employed. Using the

Jan 1, 1962

By T. R. A. Davey

A Survey of current and recent research and developmental work is supplemented by predictions for processes which should be developed over the reminder of this century.

Jan 1, 1970

IN speaking, on the subject, "Engineer-Citizens," at the Lehigh Valley Mineral Industries Conference dinner, on April 26, at Easton, Pa., George Otis Smith, Director of the United States Geological Survey and President of the American Institute of Mining and Metallurgical Engineers, said in part: "It would be carrying coke to Connellsville to bring to the Lehigh Valley the idea that mineral resources are the foundation of national prosperity. Unfortu-nately, however, this obvious, fact is not everywhere recognized. Too many of our economists, journalists, statesmen and other dopesters of present business con-ditions stress the human factor so strongly that they overlook the material with which men work out their destiny. To them the financial psychology of Wall Street and the political logic of Capitol Hill and the business commonplaces of Main Street all loom far larger than the geology of the Lehigh Valley or the engineering triumphs of Bethlehem, or, the creative thinking at Lehigh and Lafayette. "The present situation in the industrial and .business world is a complex of interacting causes and reacting effects not easily itemized and entered on our trial balance sheet. But, chief among the liabilities of today is the excess of production capacity in most branches of industry. The farmer has no. monopoly in his desire for relief. Whether your professional connections are with steel or cement, coal or oil, copper, or zinc, you; know too well that for, the moment America is over-engined, and you keenly realize the ever-present hazard of industry speeding up regardless of the curves or grades just around the corner.

Jan 5, 1928

By L. Bombardieri, H. F. Mills

Iron King mine, producing gold-silver-lead-zinc-ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pat tern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length, with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth, the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 5 ½ -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material.

Jul 1, 1956

By JAMES QATLEY

THE atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantities. At no time since the blast-furnace became an important and widely used apparatus-even when it was operated in the most crude manner-have the variations in composition of the raw materials used been as frequent and as great as the variations in humility of the atmosphere. Important, improvements have been made in the blast furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing engines, the increased protection given to the bosh walls, and the careful preparation of&apos; the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least., a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humility as variable to-clay as when first blown into a primitive blast-furnace, appeared to stand as a Barrier to

Jan 1, 1905

By A. J. Lena, M. F. Hawkes

Changes in hardness, tensile properties, microstructure, electrical resistance, and X-ray diffraction effects indicate that lattice strains are necessary for the embrittlement of ferritic stainless steels when heated for relatively short times at 475°C (885°F). It is suggested that 475°C (885°F) embrittlement is due to the accelerated formation of an intermediate stage in the formation of s under the influence of these strains. FERRITIC stainless steels (low carbon alloys of iron with more than 15 pct Cr) are subject to two forms of embrittlement when heated in the temperature range of 375° to 750°C. The embrittlement which occurs after long time heating between 565" and 750°C is well understood; it is caused by the precipitation of the hard, brittle s phase. Sigma is an intermetallic compound of approximate equi-atomic composition with an extended range of formation in Fe-Cr alloys. The maximum temperature at which this form of embrittlement can occur is dependent upon chromium content; and is approximately 620°C for a 17 pct Cr steel and 730°C for a 27 pct Cr steel. The other form of embrittlement occurs after relatively short heating periods in the range of 375" to 565°C; in the higher chromium steels, hours may be sufficient as compared to months for s embrittlement. This phenomenon is not at all well understood and several controversial theories have been proposed. The rate and intensity of embrittlement increase with increasing chromium content but the maximum rate occurs at 475°C re-gardless of chromium content. As a result of this, the phenomenon has been termed 475°C (885°F) embrittlement. The effect of 475°C embrittlement on the properties of ferritic stainless steels has been thoroughly reviewed by Heger.1 The embrittlement causes a pronounced decrease in room temperature impact strength and ductility, a large increase in hardness and tensile strength, and a decrease in electrical resistivity and corrosion resistance. Microstructural changes accompanying embrittlement are minor and difficult to interpret with a general grain darkening, appearance of a lamellar precipitate, grain boundary widening, and precipitation along ferrite veins having been reported at various times. With the exception of reported line broadening, X-ray diffraction studies by conventional Debye analysis of solid samples have been of little value. BY making use of electron diffraction methods, Fisher, Dulis, and Car-roll&apos; have recently shown the existence of a chromi-um-rich, body-centered cubic phase in 27 pct Cr steels which had been aged at 482°C (900°F) for as long as four years. Two types of theories have been advanced to account for the embrittlement. The first of these requires the precipitation of a phase not inherent in the Fe-Cr system with various investigators suggesting a carbide,3 nitride,3 phosphide,4 or oxide." Theories of this type have difficulty accounting for the influence of alloying elements on the embrittlement and for the facts that a minimum chromium content is necessary for embrittlement and the intensity of embrittlement increases with increasing chromium content. The second type of theory that has been proposed relates 475°C embrittlement to s phase formation which is inherent in the Fe-Cr system. An assumption of this kind can adequately explain the influence of alloying elements, for they exert an effect on 475°C embrittlement similar to that on s phase for-mation as can be seen in Table I. The minimum chromium content is essentially the same for both phenomena and it has been shown12,13 that s is a stable phase in the embrittling temperature range. In addition, it has been reported14,15 that pure alloys embrittle to the same extent as commercial type alloys. There are, however, several factors which have prevented complete acceptance of a s phase theory. Foremost of these is that the embrittlement can be removed by reheating for short time periods above 600°C, which in the higher chromium steels is within the stable s region. No s has ever been observed after one of these curing treatments, nor has any s been found as a result of embrittlement at 475°C. In addition, the simple precipitation of s cannot explain the time-temperature relationships for reactions between 350°and 750°C. This behavior is shown schematically in Fig. 1. Newell 16 and Ried-rich and Loib4 have shown that 475°C embrittlement follows a C-type curve as illustrated, while Short-

Jan 1, 1955

By Bradley Stoughton

A LL over our great country I have been privileged to see, during the last six weeks, the manifestation of a new spirit among engineers. Partly under the inspiration of leaders whose influence has been felt not only nationally, but internationally, - partly through the recognition of the service that engineers have been able to render to the nation during the recent crisis, a new self-consciousness has been acquired by the individuals, and now this self-consciousness seeks expression in opportunities for service and participation in public affairs. The engineer . no longer sees himself a mere reservoir of information to be tapped when some one is in need of cold facts, no. more an administrator of mere material things, but a potential administrator of- public affairs, a citizen and a human being, with the responsibilities, as well as the privileges of citizenship.

Jan 1, 1920

By WILLIAM E. NEWNAM

THE molding and loading of pig lead has, in the past, been accomplished mainly by the strong arm method and, as the pigs are usually loaded directly into the cars, it has been a hot and laborious task. Of late years it has been difficult to obtain men willing to perform such labor and the need has been felt for loading and molding machinery which would eliminate all manual handling of the hot pigs and which would be sufficiently compact to permit of installation in existing plants with little or no

Jan 1, 1924

By P. S. Rudman

The solubility limit and the diffusivity of carbon in molybdenum have been obtained by duffising carbon into molybdenum rods from a Mo + Mo2C powder mixture. The solubility limit was taken as the long-time asymptotic limit of the rod composition. The diffusiv-ity was obtained from fractionally saturated rods from the rate of change of the average composition. Compositions were determined by chemical analysis. The solubility limit obtained is: WhILE the Mo-C system is important in refractory alloy technology neither the solubility limit nor the diffusivity of carbon in molybdenum is unambiguously known. In Fig. 1 the Mo-C phase diagram is presented. The heavy lines, the terminal solution solubility limit, and the eutectic temperature are results of the present investigation and will be discussed in detail later. However, it is readily seen that the previously published solubility limit determinations, Few and Manning1 and Fromm and ROy2 differ by up to an order of magnitude. The general form of Fig. 1, the Mo2C field, and a eu- tectic temperature -2200°C are due to an early Investigation by Sykes et a1.3 Although they did not determine the solubility limit, they did establish that the maximum at the eutectic temperature was about 1000 ppm. The only other prior data found on the solubility limit is from a lattice-parameter study by Speiser et a1 .,4 from which it can be concluded that the maximum solubility is greater than 1800 ppm. There does not appear to be any data oh the diffusivity of carbon in molybdenum. However, Samsonov and Epik5 have determined, from the rate of growth of an MozC layer, the diffusivity of carbon in Mo2C, and this has been erroneously interpreted, for example by ~c~eil,&apos; as applicable to diffusion of carbon in molybdenum.

Jan 1, 1968

By T. L. Joseph

BLAST furnaces are most efficient thermally when the C02 in the top gas is highest. Oxygen introduced in the air blast is converted to CO in the combustion zones. The extent to which CO, generated in front of the tuyères, is converted later to C02 depends upon the ratio of ore to coke in the charge and the degree to which C02, formed by reduction of iron oxides with CO, reverts to CO by the secondary reaction C + C02 = 2C0. About 300 to 400 lb. of carbon1 per ton of pig iron is normally involved in the solution-loss reaction or direct reduction of FeO with carbon, which produces the same over-all results; that is, lower C02 in the top gas. Riche has recently reported a reduction in fuel consumption at slower rates of blowing on two furnaces in spite of higher heat losses per ton of iron. Lower fuel consumption at slow operating rates was due to more complete reduction of the ore that resulted in higher C02 in the top gas and consequently more efficient use of carbon. Kinney3 has reported substantial savings in fuel as a result of crushing and sizing the ore charge. Improvements in practice brought about by sintering magnetite concentrates, flue dust and fine ores have been due to the establishment of conditions favoring more complete reduction of the ore in the upper part of the furnace. The extent to which oxides and fluctuations in composition in pig iron affect the quality of steel and finished product needs further study. There is evidence that more thorough preheating and reduction of the ore in the upper part of the furnace tend to give a better quality of iron. Bogatzkii4 found from laboratory work that the amount of oxygen enter-

Jan 1, 1936

By A. F. Meger

Coal treatment by oil spraying receives special attention at the Georgetown plant for the dividends it pays in satisfying present customers and attracting new markets. Customer satisfaction requires care, quality control, and use of suitable oils. REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal CO. who have helped develop, over a number of years, an efficient and flexible method for spraying controlled amounts of oil on coal. Since the Georgetown preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage. The graph, Fig. 1, shows results of the original tests made with a 700-sec residual blend and a 500-sec lubricating oil on Georgetown stoker coal of 1¼x3/8-in. size.* The advantages of better price, improperly blended can raise havoc. Some.,pale oils also, although odorless when delivered, give off a sweet sickening odor when atomized under pressure. It is recommended that all products be tested before they are used. There is a specific place for all spraying oils. For example, at a power plant a severe dust condition exists around the stockpile area and in parts of the plant. The cheapest spraying oil made, regardless of odor, will do an excellent job in this case and will save the company 3 to 5c per gal or more. Domestic trade, on the other hand, must be carefully handled to prevent complaints about odor, and the only way to do this is to stay with the proved products after the odor tests have been made. The preparation plant at Georgetown has facilities to handle either tank car or tank truck deliveries. Steam is available at the unloading point if the weather is severe, and there is an indicator at the unloading point to prevent overflowing the 20,000-gal underground storage tank. Systematic test samples are removed from each delivery and sent to the lubrication engineer to insure quality control. Fig. 3 illustrates the chutes in which smaller sizes of coal are treated. Fig. 4 shows the entire spraying system. Buried in the ground is a 20,000-gal tank with immersion heaters grouped around the feeder line to insure adequate gravity flow to the pump under all conditions of weather. Oil flows to a 500-gal preheating tank where the temperature is kept about 150°F by six 1½-kw immersion heaters thermostatically controlled. Hot oil is fed through a self-cleaning disc-type filter to the hydraulic pump. Valves and piping make it possible to transfer oil from one tank to another or to drain the lines for maintenance purposes. All this equipment is below ground level in a covered pump room,

Jan 1, 1955

By L. O. Bacon

IN the spring of 1952 Calumet and Hecla Inc. began a geophysical program near Shullsburg, Wis., in the Wisconsin-Illinois lead-zinc district, to assist the geological and drilling exploration programs. Sphalerite, the ore mineral in this area, occurs with a considerable amount of marcasite. In general the higher the percentage of sphalerite in the ore, the higher the percentage of marcasite; however, there may be mineralized zones high in marcasite but low in sphalerite. Orebodies in general are relatively narrow and elongated. Reconnaissance exploration of virgin areas consisted of drilling along lines at 500 to 1000-ft intervals. Whenever a mineralized zone was intersected additional drilling was done to determine whether or not the zone carried zinc percentages of ore grade and, if so, to delineate the body. Calumet and Hecla Inc. was interested particularly in a method that would show the direction and position in which to drill from the original discovery hole. This suggested a method of contacting the orebody, which occurs at depths ranging from 100 to 200 ft, with one electrode. After a number of procedures had been considered it was decided to use equipotential line methods. Instrumentation and Field Procedure: The power source used was a 400-cycle Signal Corps motor-generator having a rated output of 1200 w at 115 v. The detection unit consisted of test probes, a two-stage amplifier, and &apos;head phones for determining the equipotential line by audio null. Field procedure consisted of contacting the sulfide body in the hole by a specially built spring-loaded expanding electrode which would be lowered into the hole, in the closed. position, until it reached the mineralized zone. At that point the mechanism was released so that the arms would make contact with the walls of the hole in the same manner that a well-bore caliper does. This electrode was then connected to the generator, the other terminal of which was connected to the surface electrode. The surface electrode was either a point, a straight line, or a circular line electrode. The point surface electrode was placed at a considerable distance from the hole, that is, 2500 to 5000 ft, depending somewhat upon the depth to the sulfide zone and the distance from the hole containing the subsurface electrode to which exploration was considered. A higher voltage output from the power source would have been desirable, although no difficulty was encountered in determining null points to a distance of 500 ft. Straight line electrodes used were approximately 1000 ft in length at a distance of approximately 1000 ft from the hole containing the subsurface electrode. The circular line electrode used consisted of 4400 ft of bare No. 10 copper wire, which provided a circle of 700-ft radius. All line electrodes were fastened to the ground at 20-ft intervals with copper staples 4 in. long. Equipotential points were determined at 25 to 100-ft intervals. Location of the points was made by plane table and stadia. In open country with a three-man crew, the points were plotted as they were determined. With a two-man crew, pegs were placed at equal potential points and surveyed in after several equipotential lines were determined. Although interpretation of results given in this paper is qualitative, the paper as a whole would not be complete without a discussion of the theoretical distribution of potential due to a circular line electrode. The theoretical distribution would be required if a quantitative interpretation of the measured potential distribution were to be made. The theoretical potential distribution due to a circular line electrode can be obtained by means of Legendre polynomials. Using the method as developed by Weber,&apos; the potential for a circular line electrode in a semi-infinite, homogeneous, isotropic medium can be expressed, using the spherical coordinate system, as: V(r,n) = pi/2pR[S(r/R)nPn(cos?)Pn(cosa)]r<R [1] er V(r,a) =pI/2pr[S(r/R)Pn(cos?) Pn(cosa)]r>R [2] where: 0 is the angle at the origin, taken on the axis of the circular electrode between the axis and the line drawn to the circumference of the circular electrode. a is the angle between the axis and the radius, r.

Jan 1, 1957

By F. F. Schmidt, H. R. Ogden, E. S. Bartlett

Continuing tantalum alloy development studies have been concerned with a more detailed investigation of promising binary, ternary, and more complex tantalum alloys containing Groups IV-A, V-A, VI -A. VII-A, and VII-A metal additions. A primary objective of these studies was to improve the elevated temperature strength of tantalum with minimum degradation of fabricability and low-temperature ductility by alloying. Several alloys were found to exhibit hot tensile strengths in the excess of 25, 15, and 10 ksi at 2700°, 3000°, and 3500°F, respectively, combined with excellent cryogenic toughness and ductility. Particularly outstanding in this respect are alloys in the system Ta-Mo-W. Ternary parameter curves describing hot-strength, low-temperature ductility, recrystallization temperature, weld ductility, and fabricability are presented for the Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W systems. At present, only four metals qualify for large scale structural applications at temperatures above about 1800°F. These are tungsten, tantalum, molybdenum, and columbium. Research and development work on these refractory metals has progressed to the point where efforts are now primarily directed toward the improvement of high- and low-temperature mechanical properties through alloying. High melting point combined with excellent low-temperature ductility, fabricability, toughness, weldability, and high solubility and tolerance for both substitutional and interstitial solutes are important attributes of tantalum. Conversely, its high density and relative scarcity compared with other refractory metals are the major deterrents to the use of tantalum. Early studies in the Battelle alloy development program established base line data on the mechanical and metallurgical properties of high-purity tantalum.&apos; These studies were extended to include a preliminary investigation of the effects of various alloying elements on the established base properties.2,3 Recent studies involved a more detailed investigation of promising binary alloys containing Cb, Hf, Mo, Os, Re, Ru, and W, and ternary Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W alloys. Results of major importance obtained are given in this article. EXPERIMENTAL PROCEDURES Electron-beam-melted tantalum (Wah Chang) and high-purity alloying elements were consolidated as 150-g ingots by multiple nonconsumable arc melting under a partial atmosphere of helium. Homogeneity of the button ingots was checked radiographically. Alloy buttons measured about 1-1/2 to 1-3/4 in. in diam by about 0.35 and 0.50 in. thick. Nominal alloy compositions were checked on each alloy button by weighing after arc melting. In most instances, weight losses were within 3 pct of the total weight charged. Subsequent chemical analyses on a number of selected alloys showed interstitial contents to range as shown below: Range of Interstitial Content, ppm 0 C N H 25-75 50-100 10-50 1-5 Metallic alloying additions were found to agree well with nominal compositions based on weight change data. Fabrication directly from the cast button to sheet was conducted at low (75° to 900°F), intermediate (1800° to 2000°F), or high (3000°F) temperatures, depending upon alloy content and hardness. Evacuated stainless steel or molybdenum packs were used for fabrication at intermediate and high temperatures, respectively. The temperature required to complete recrystal-lization in one hour was determined by hardness measurements and metallographic observations (longitudinal test sections) after vacuum annealing at 180°F intervals in the range 2010° to 2910°F. All mechanical property evaluations were conducted on recrystallized sheet, nominally 0.04 in. thick. Weldability of the various alloys was screened using manual TIG welding techniques. Bend ductility (bend axis perpendicular to weld axis) was the criterion used for evaluation. Tensile specimens employed 0.200 by 1 in. gage lengths, and bend test specimens measured about 1 by 1/4 in. Low-temperature tensile tests were conducted using a crosshead speed of 0.02 in. per min up to the point of yielding, and 0.05 in. per min to fracture. High-temperature tensile tests were conducted in vacuum using a crosshead speed of 0.01 in. per min

Jan 1, 1963

By Frederick H. Williams

THE object of this paper is to bring to the attention of those members of the Institute who are interested in the subject, a method for the estimation of manganese, which has been frequently used in the laboratory of the Vulcan Steel Works during the last eight months, and which is deemed worthy of more general use. It is simply an adaptation of well-known processes, for the purpose of determining this element in pig iron and steel. In general, the method consists in precipitating the manganese as binoxide, dissolving in dilute sulphuric acid in the presence of an excess of a standardized solution of oxalic acid, and titrating the remainder of the oxalic acid left unoxidized with permanganate of potash. For this method, therefore,. two standardized solutions are needed, viz., a permanganate solution and an oxalic acid solution. The permanganate solution is made so that 1 c.c. is equivalent to 1 mgr. of iron. By using so weak a solution and keeping the bulk of the solution to be titrated down to 75 c.c. or a little less, the accuracy of the process is greatly increased, since the final reaction is almost if not quite as sharp as if a stronger solution were used. The oxalic acid&apos; may be of almost any strength, but if made so that 1 c.c. requires 3 c.c. of the permanganate to oxidize it, it will auswer well. The process is then, as follows : from 1 to 2 grams of pig iron or steel are dissolved in 40 to 50 c.c. of concentrated nitric acid with the aid of heat. As soon as solution is effected, in the case of steel, add gradually and cautiously, the solution being kept boiling, sufficient pulverized chlorate of potash to precipitate the manganese as binoxide. Two grams will be a great abundance. In the me of pig iron, first remove the carbon and silica by filtering the solution through asbestos and washing with concentrated nitric acid. Filter the strong acid solution in which the binoxide has been precipitated, through asbestos with the aid. of the filter pump. When it has entirely passed through wash well with water. Blow the contents: of the funnel into the beaker in which the precipitation was made and rinse the funnel with a little water.

Jan 1, 1882

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) Members and guests who called at Institute headquarters during the period Feb. 10, 1917 to Mar. 10, 1917: F. H. Armstrong, Vulcan, Mich. G. Komar, Staten Island, N. Y. Franklin Bache, Philadelphia, Pa. H. M. LaFollette, LaFollette, Tenn. R. A. Bingham, W. Orange, N. J. H. Mortimer-Lamb, Montreal, Canada. G. S. Blair, Pittsburgh, Pa. J. S. Lane, New York, N. Y. Graham Bright, Pittsburgh, Pa. D. H. McLaughlin, Cambridge, Mass. C. A. Burdick, New York, N. Y. F. J. McMahon, Wilkes-Barre, Pa. Frederick P. Burrall, Dawson, Y. T. F. Oskar Martin, San Francisco, Cal. William Campbell, New York, N. Y. C. Mentzel, New York, N. Y. G. L. Carlisle, Jr., New York, N. Y. T. C. Merriman, New Haven, Conn. J. Murray Clark, Toronto, Canada. K. -A. Pauly, Schenectady, N. Y. Wayne Darlington, Philadelphia, Pa. , Francis R. Pyne, Elizabeth, N. J. Ralph W. Deacon, Elizabeth, N. J. C. S. Robinson, Youngstown, O. P. St. Jon Dixon; So. Porcupine, Canada. W. A. Scheuch, New York, N. Y. A. E. Drucker, New York, N. Y. Jesse Scobey, New York, N. Y. Lucien Eaton, Ishpeming, Mich. Dunbar D. Scott, Rochester, N. Y. W. E. Goldsborough, New York, N. Y. W. C. Smith, Elizabeth, N. J. C. Marshall Gravatt, Port Royal, Va. Charles Spearman, Mt. St. Patrick, Can. C. N. Hickok, Cleveland, O. . - Harold C: E. Spence, Duncan, Ariz. C. Vey Holman, Rockland, Me. M. M. Thompson, Morsemere, N. J. W. F. Jahn, Kirkland Lake, Canada. Benjamin F. Tibby, Salt Lake City, Utah. F. E. Johnesse, Boise, Ida. J. S. Unger, Pittsburgh, Pa. E. C. Johnson, Chicago, Ill.

Jan 4, 1917