Search Documents

Jan 1, 1920

By Yves Dardel

The literature concerning the remelting of alunlinum and its alloys is very rich. Unfortunately the majority of the papers on this subject have no scientific value, for the theories or explanations are too often in opposition to the laws of physical chemistry. Furthermore only a few of the methods of purification are considered in the literature. Hence it has seemed necessary to the author to sketch a general theory of the purification of secondary aluminum. The purpose of the purification is to eliminate the impurities that the charges, and the atmosphere of the furnaces bring into the bath during the successive remelt-ings. Indeed scrap as well as metal can be used when soiled with oil, greases, water, or others, if it has been sufficiently dried and contains oxides. At the melting point of the metal, the oils and greases are decomposed into their constituent elements H², O2, H²O, co², CO, CH,, and others. These gases are added to the corresponding gases in the atmosphere of the furnace. The impurities introduced into the metal during the remelting will accordingly be the products resulting from the action of these gases on the liquid bath. The quantity of hydrogen that is soluble in aluminum and its alloys is given by the relation of sieverts3 as a function of its partial pressure PH2 in the atmosphere m = K vPH² [I] where K is a constant, which depends only upon the temperature and increases with it. The experiments of Rijntgen and Braun4, RÖntgen and M611er5, Bircum-shaw6 and Winterhagerl have rendered it possible to determine the value of K, when the temperature is less than 1.000°C. One obtains: log K = - 4,702.5T + o 238 [2] Besides its usual significance, the term Ph~ represents also the internal pressure of dissolved hydrogen, since in the equilibrium, that is1 when no gas exchange Occurs between the two phases, the Pressures of hydrogen in the metal and in the atmosphere must be equal. Eq I shows that when the partial pressure of H2 increases the amount of dissolved hydrogen in equilibrium increases, and that, if the contrary Occurs, the quantity of H² should diminish. However, if for any reason the diffusion of hydrogen is hindered and the total amount of dissolved gas remains constant while the temperature decreases, the internal pressure of H² increases until it reaches the value of the hydrostatic pressure. At this point, bubbles of hydrogen appear in the bath and escape out of it. The amount of hydrogen in the metal is then limited by a a depending On the hydro- static pressure, which is practically equal to one atmosphere. Indeed hydrogen does not accumulate in the form of a hydride appearing as a separate solid phase. However1 even the mechanism of the solubility is not yet elucidated. One does not know exactly as yet, whether the

Jan 1, 1949

By Yves Dardel

THE literature concerning the remelting of aluminum and its alloys is very rich. Unfortunately the greater part of the papers about this subject have no scientific value, for the theories or explanations are too often in opposition to the laws of physical chemistry. Furthermore only a few of the methods of purification1,2 are considered in the literature. Hence it has seemed necessary to the author to sketch a general theory of the purification of secondary aluminum. The purpose of the purification is to eliminate the impurities that the charges and the atmosphere of the furnaces bring into the bath during the successive remeltings. Indeed scrap as well as metal can be used when soiled with oil, greases, water, .. , if it has been sufficiently dried and contains oxides. At the melting point of the metal, the oils and greases are decomposed into their constituent elements H2, 02, H2O, C02, CO, CH4, and others. These gases are added to the corresponding gases in the atmosphere of the furnace. The impurities introduced into the metal during the remelting will accordingly be the products resulting from the action of these gases on the liquid bath. The quantity of hydrogen that is soluble in aluminum and its alloys is given by the relation of Sieverts3 as a function of its partial pressure PH2 in the atmosphere [m = K _%/PH, [I]] where K is a constant, which depends only upon the temperature and increases with it. The experiments of Röntgen and Braun4, Röntgen and Möller5, Bircumshaw6 and Winterhager7 have rendered it possible to determine the value of K, when the temperature is inferior to 1.000°K. One obtains: [log K = - 4,702.5 + 0.238 [2]] Besides its usual signification, the term PH2 represents also the internal pressure of dissolved hydrogen, since in the equilibrium, that is, when no gas exchange occurs between the two phases, the pressures of hydrogen in the metal and in the atmosphere must be equal. Eq I shows that when the partial pressure of H2 increases the amount of dissolved hydrogen in equilibrium increases, and that, if the contrary occurs, the quantity of H2 should diminish. However, if for any reason the diffusion of hydrogen is hindered and the total amount of dissolved gas remains constant while the temperature lowers, the internal pressure of H2 increases until it reaches the value of the hydrostatic pressure. At this point, bubbles of hydrogen appear in the bath and escape out of it. The amount of hydrogen in the metal is then limited by a maximum depending on the hydrostatic pressure, which is practically equal to one atmosphere. Indeed hydrogen does not accumulate in the form of a hydride appearing as a separate solid phase. However, even the mechanism of the solubility is not yet elucidated. One does not know exactly as yet, whether the

Jan 1, 1947

ROESLER MAX-Geology of the Iron-Ore Deposits of the Firmeza District, Oriente Province, Cuba. Discussed by William Kelly, J. T. Singewald, Jr., B. L. Miller, J. D. Irving, L. C. Graton, C. P. Berkey 439 SINGEWALD, J. T., JR., AND MILLER, B. L.-The Manganese Ores of the Lafayette District, Minas Geraes, Brazil. Discussed by L. C. Graton, J. T. Singewald, Jr., F. Lynwood Garrison HARDER, E. C.-Manganese Ores of Russia, India, Brazil, and Chile. Discussed by J. T. Singewald, Jr., E. C. Harder 454 SCHRADER, FRANK C.-Geology and Ore Deposits of Mohave County, Arizona. Discussed by J. C. Anderson McDOWELL, J. SPOTTS-A Study of the Silica Refractories. Discussed by J. W. Richards, H. D. Hibbard, W. F. Rochow, J. B. Umpleby-: 460 PHALEN, W. C.-The Conservation of Phosphate Rock in the United States. Discussed by E. G. Spilsbury 462 NORTON, S., AND LEFEVRE, S.-The Magnetic Concentration of Low-Grade Iron Ores. Discussed by G. C. Foote, J. L. W. Birkinbine, F. L. Nason 462

Jan 4, 1917

By N. A. Gokcen, S. Fujishiro

The dissociation pressure of Cr3C2 has been measured in the range of 1908" to 2237°K by means of graphite Knudsen effusion cells. It has been found that Cr3C2 vaporizes according to the following reaction: 1/3 Cr3C2 (s or 1) = 2/3 C (graph.) + Cr (g). The equilibrizcm pressure, P, of Cr (g) is found to be log Ps=- - (21,194/T) + 6.525 over solid Cr3C2 and estimated as log P, = - (19,535/T) + 5.76 over liquid Cr3C2. CARBIDES of chromium are of great importance in alloy steels and cemented carbides. The published data on their therm odynamic properties at high temperatures, however, are meager. The heat capacity and change in entropy of Cr3C2 were determined calorimetrically by Kelley and Moore1 in the range of approximately 50" to 300°K, and by Oriani and Murphy2 from 297" to 1188°K. The standard entropy of Cr3C2at 298.15°K, obtained by Kelley.7 was later confirmed by DeSorbo.4 Equilibrium in the reaction was investigated by Boericke.5 A recent tabular summary

Jan 1, 1962

By A. E. Brugger

SOME 2,000 years ago Pliny is supposed to have said, "Out of Africa always something new." It may perhaps even now be news to a great many that the Belgian Congo has in recent years been producing approximately a quarter of a ton of diamonds annually. For that is what the 1 1/4 million carats, the recovery from 40-odd operating mines, and about 20 or 25 per cent of the world's normal consumption, amounts to. In 1915, first exploitation operations produced less than 50,000 carats from two mines. The rapid expansion of operations following the Euro¬pean war meant a most rapid development of a virgin land. The interior is now reached by air in one day from the mouth of the Congo River, where steamers unload mail and passengers from Antwerp. This trip formerly consumed 4 to 6 weeks by a narrow-gage, wood-burning, railroad around the rapids of the lower Congo and Livingston Falls; by river boat to the heads of navigation, Djoko Punda on the Kasai or Luebo on the Lulua; and thence by caravan of native porters over narrow-trails to head¬quarters on the Tshikapa. Hundreds of miles of automobile roads have been constructed over veldt and through forest, bridging streams and ferrying rivers. The railway from Capetown to the Katanga copper district to the East, once two months away by trail is now reached in 2 or 3 days over fair automobile highway. Native "boys" who a few short years ago wore little more than a smile and a string of beads and to whom a wheelbarrow was a complicated piece of machinery, are today driving Fords, tending boilers and engines and operating electrical equipment, or are capable mine workmen, machinists and artisans, and dressed in all manner of cast-off white man's clothing. Even as late as 1920, due to difficulties of securing and transporting machinery during and just after the war, the crudest hand operations were the rule for the excavation, sizing, and concentration of the diamondiferous gravel. All washing and concentration is now mechanized, using steam or electric power, and where operations are sufficiently large to permit competition with native labor costs, excavation and transportation are also accomplished by machinery.

Jan 1, 1932

By Stanley F. French, Bruno F. Koch

Although the amount of dust that will be actually recovered in the six main dust-control systems cannot be accurately stated until the tests mentioned previously are carried out, it is estimated that the average air entering the wet collectors will contain around 5 grains of dust particles per cubic foot. This means that the six systems handling a total of about 133,000 cu.ft. of air per minute will return about 68 1/2 tons of dust to the concentrator per day and since the copper in this dust will average around 2 per cent, the total recovery is approximately 1.37 tons of copper every 24 hours. This important copper recovery is not due entirely to the dust-control system since in a plant without control only the duct that is dispersed to the atmosphere represents a loss. A conservative estimate of the recovery of copper solely due to the dust control system would be about half of the total or approximately 0.70 tons of copper per day.

Jan 1, 1942

H. W. Turner, San Francisco, Cal. (communication to the Secretary*): This excellent paper apparently represents the results of extensive observation and experience among the mines of the Mother-Lode, but I strongly question its relegation of the dioritic intrusions to the period of fissuring and ore-deposition. The dioritic rocks referred to are evidently those areas represented by Ransome in the Mother-Lode folio1 as meta-diorites, and, as he says, are merely basic facies of the great granodiorite batholite of the Sierra Nevada. If followed downward I venture to predict that these meta-diorite areas would be found to connect with the great batholite, and to be in fact mere apophyses of it. I see no reason for supposing that these apophyses were intruded into the Mother-Lode slates at a period later than the intrusion of the granodiorite in general. The period of fissuring was subsequent to this intrusion; the basic granodiorite or quartz-diorite areas of the foot-hill region are themselves fissured extensively; and the fissures were filled with quartz, apparently during the same general period of the formation of the Mother-Lode veins. Prichard and Ransome2 both refer to the deposition of quartz in the same lode at different periods resulting from a reopening of the fissures. Some time since, I saw in the stopes of the

Jan 1, 1904

By NORMAN D. FitzGkrald

IN 1942 the outstanding characteristic of the petroleum industry was the multiplicity of war-induced distortions in virtually every segment of the business. So devastating was the success of the Nazi submarine campaign along the shores of the western Atlantic and on transoceanic routes that within six months after our entry into the war petroleum rationing was necessary in the East Coast area. The conquest of the Netherlands Indies by the Japanese three months after the opening of the war in the Pacific cut off our normal sources of rubber, and in our first year of war nationwide rationing of gasoline had to be invoked to conserve rubber-borne transportation facilities. Meanwhile the oil industry faced the imperative necessity for rapid expansion in the output of aviation gasoline and later accepted the vast responsibility for developing a new industry. synthetic rubber manufacture. Probably no other essentially peacetime industry has been forced to make so many complicated adjustments, yet its response to its wartime obligations has been nothing short of dramatic.

Jan 1, 1943

By W. L. Remick

The hydrotator coal-cleaning process was developed as an economic necessity to meet the ever-increasing demand for an inexpensive method of cleaning coal down to the sizes ordinarily referred to as "dust." As the most urgent demand seemed to be in the anthracite field, all experimental work has been conducted in that territory during the past two years, with the exception of a few months during the strike of 1925-26, when some experiments were performed in the Alabama bituminous fields. The first commercial plant was constructed at the Middle Creek Colliery of the Philadelphia & Reading Coal & Iron Co.,. Pottsville, Pa. This plant is now operating. Application The field of application of the process is: 1. Cleaning anthracite fines, ordinarily described as "slush" or "silt." Slush contains all sizes from 3/32 in. down to and including I(dust." (Anthracite passing a 3/32-in. mesh is also referred to as No. 2 Barley and No. 4 Buckwheat.) 2. Cleaning sizes too fine for recovery by other methods. 3. Removal of coal from sand circulated in the Chance sand-flotation process. 4. Cleaning of bituminous sizes from % in. down to "dust." 5. As equipment for the performance of the froth flotation process. 6. Other separating, extraction and washing processes which may be considered outside the realm of coal cleaning. Principle of Operation Fig. 1 shows the method of classification practiced under the Hydrotator patent.' In coal cleaning the machines are operated as "hindered settling" classifiers, the flow of solids and liquids being so controlled that the units may be combined in series.

Jan 1, 1927

By Norman J. Sather

LOCATION AND HISTORY The Bunker Hill Mine is situated on the south side of the Coeur d’Alene River in Shoshone County of Northern Idaho near the City of Kellogg. Kellogg, the largest in the Coeur d’Alene District cities, is at an elevation of 2,300 feet and has a population of approximately 7,000 people. It can be reached by air, railway or highway. The history of the Bunker Hill Mine dates back to August 26, 1885, when Noah S . Kellogg found the outcrop of the Bunker Hill ore body on the hillside above the present town of Wardner, Idaho, in Milo Gulch. A small concentrator was erected in 1886. Before the railroad came, the mine output was transported by mule teams to the head of navigation on Coeur d’Alene Lake. After ten years of production, an interest was purchased in the Tacoma Smelter at Tacoma, Washington, to which the entire output was shipped. In 1916 and 1917 a modern lead smelting plant and refinery was erected and in 1927 and 1928, a modern Electrolytic Zinc Reduction Plant was built and put into operation by the Sullivan Mining Company which was 50% owned and now totally owned by The Bunker Hill Company. GEOLOGY AND MINERALOGY The Bunker Hill ore bodies are found in gray and greenish gray quartzite and argillaceous quartzite of Precambrian age and are known as the Revett and St. Regis formations. Most of the ore bodies are found in the St. Regis formation.

Jan 1, 1970

By T. Watanabe, S. Karashima, H. Oikawa

Creep tests of a! iron and its solid-solution Fe-Mo, Fe-Co, and Fe-Si alloys with bcc structure were conducted under constant stresses in ferromagnetic and paramagnetic temperature regions above 0.5T,(T, is the absolute melting temperature). It was found their high-temperature creep behavior changed in the vicinity of the magnetic transformation temperature, that is Curie temperature, TC. In the ferromagnetic region below the steady-state creep rates were lower than those expected from the extrapolation of the data in the paramagnetic region, the amount of decrease being affected by solute addition. Also, activation energies for steady-state creep were different in the two temperature regions. The observed changes were concluded to be due to the effect of ferromagnetism on diffusion. It is well-known that plastic deformation of metals and alloys in the temperature region where mobility of atoms becomes high enough is controlled by atomic diffusion." Many experimental results394 on fcc and hcp materials have been reported to confirm this view. In bcc metals and alloys, not much basic investigation of creep deformation has been performed. In particular, experimental work on iron5-&apos; and its alloys, covering a quite wide temperature range is extremely scarce. On the other hand, the effect of ferromagnetism on diffusion has recently been demonstrated in a iron and its alloys;&apos; it has been made clear that diffusion rates in ferromagnetic temperatur~e region are significantly lower than those expected from diffusion measurement in the paramagnetic region. Therefore, it is concluded that the magnetic effect influences the high-temperature creep behavior in a! iron and in its alloys. The present authors have conducted creep experiments on a iron and its solid-solution alloys over a very wide temperature range, and have demonstrated the magnetic effect. A part of the result has already been reported elsewhere.26 In this paper, the experimental results will be described in detail. While the manuscript was in preparation, a similar magnetic effect on creep deformation of a iron was reported by Ishida . Though their experiments covered an extremely wide temperature range, the creep stresses varied from several thousand psi to several ten thousand psi with decreasing temperature. Consequently, it may be said that there remain some questions concerning their results. I) EXPERIMENTAL PROCEDURE The materials used in the experiments were pure iron and its alloys; they were prepared by vacuum melting (10"" mm Hg) electrolytic iron (99.9 pct), molybdenum powder (99.9 pct), ultrapure silicon, and cobalt pellet (99.5 pct) in alumina crucibles. The ingots were hot-forged to plates 10 mm thick and 50 mm wide, and then were hot-rolled at about 700°C into sheets 1 mm thick. Creep specimens, 5 mm in width and 15 mm in gage length, were machined from the sheets. They were annealed at temperatures which were well above their respective recrystallization temperatures. The chemical compositions of the metal and alloys are shown in Table I together with their heat treatments. High-temperature creep tests by the use of a lever-type creep testing machine were carried out in argon atmosphere under constant tensile stress. In order to keep &eep stress constant within about *0.5 pct, stress change due to specimen elongation was compensated by tensile force of a stainless-steel bellows which was inserted between the loading lever and lower specimen grip with the assumptions of a linear relationship between change in cross section and strain and uniform strain along the section. Beyond the limit of compensation by the bellows, small amounts of load were removed after appropriate strains. The testing temperatures were maintained to within i2"C of the reported values. Creep deformation was auto-graphically recorded at the upper (moving) specimen grip using a linear differential transformer which was held by a stainless-steel rod mechanically connected to the lower specimen grip. It was also directly measured with a dial-gage reading to -& mm. 11) EXPERIMENTAL RESULTS AND DISCUSSION 1) Creep Curves of a Iron and Its Alloys. Creep curves of a! iron, Fe-Si, Fe-Co, and Fe-Mo (<2 at. pct Mo) alloys usually consisted of three stages, that is transient (primary), steady-state (secondary), and accelerating (tertiary) stages. An example is illustrated in Fig. 1 for a! iron. However, in Fe-Mo alloys with more than 2 at. pct Mo, an inverse transient creepZ8 was observed as indicated in Fig. 2. The inverse behavior, which varied with the amount of molybdenum, may be due to the substructure* in the annealed specimen as was sug-

Jan 1, 1969

By W. L. Remick

THE hydrotator coal-cleaning process was developed as an economic necessity to meet the ever-increasing demand for an inexpensive method of cleaning coal down to the sizes ordinarily referred to as "dust." As the most urgent demand seemed to be in the anthracite field, all experimental work has been conducted in that territory during the past 2 years, with the exception of a few months during the strike of 1925-26, when some experiments were performed in the Alabama bituminous fields. The first commercial plant was constructed at the Middle Creek Colliery of the Philadelphia & Reading Coal & Iron Co., Pottsville, Pa. This plant is now operating. APPLICATION The field of application of the process is: 1. Cleaning anthracite fines, ordinarily described as "slush" or "silt." Slush contains all sizes from %2 in. down to and including "dust." (Anthracite passing a 32-in. mesh is also referred to as No. 2 Barley and No. 4 Buckwheat.) 2. Cleaning sizes too fine for recovery by other methods. 3. Removal of coal from sand circulated in the Chance sand-flotation process. 4. Cleaning of bituminous sizes. from 3/8 in. down to "dust. 5. As equipment for the performance of the froth flotation process. 6. Other separating, extraction and _washing. processes which may be considered outside the realm of coal cleaning. PRINCIPLE OF OPERATION Fig. 1 shows the method of classification practised under the Hydrotator patent:1 In coal cleaning the machines are operated as "hindered settling" classifiers, the flow of solids and liquids being so controlled that the units may be combined in series.

Jan 1, 1927

By E. M. Norris

THE Western phosphate deposits extend over a large area in the Rocky Mountain region, comprising portions of south central Montana, southeastern Idaho, northeastern Utah, and southwestern Wyoming. A limited acreage of these deposits passed into private ownership prior to Dec. 9, 1908, at which time 7000 sq. mi. of land in these phosphate fields was withdrawn from public entry by direction of the Secretary of the Interior. Under the Act of Feb. 25, 1920 (41 Stat. 437) title to all phosphate lands in the public domain was reserved to the United States with provisions for leasing portions to citizens, corporations, states, etc. The above act, in effect, created by law a Western phosphate reserve of approximately 2,269,055 acres.

Jan 1, 1944

By C. Atkinson

A method is described for the numerical solution of the diffusion equation with a composition-dependent diffusion coefficient and applied to the radial growth of a cylinder; the radial growth of a sphere, and the symmetric growth of an ellipsoid. Sample applications of the method are made to the growth of particles of proeutectoid ferrite into austenite. RECENTLY&apos; we described a method for numerical solution of the diffusion equation with a composition-dependent diffusion coefficient for the case of the growth of a planar interface. In this paper we extend this method to describe the radial growth of a cylinder, the radial growth of a sphere, and the symmetric growth of an ellipsoid. In the latter case, limiting values of the axial ratios of the ellipsoid reduces the problem to one of a cylinder, a sphere, or a plane depending on the axial ratio. A check on these limiting values is made in the results section. In all of these cases we consider growth from zero size. A natural consequence of this assumption as applied to the sphere, for example, is that the radius of the sphere is proportional to the square root of the time. This is consistent with the condition that the radius is zero initially, i.e., grows from zero size. It may be argued that it is more realistic to consider particles which grow from a nucleus of finite initial size; even in this case the analysis of this paper is likely to be applicable. This can be seen if a comparison is made of the work of Cable and Evans,2 who consider a sphere of initially finite size growing by diffusion in a matrix with a constant diffusion coefficient, with the results of Scriven3 for growth from zero size. This comparison shows that the rates of growth in each case differ trivially by the time the particle has grown to about five times its initial size." This investigation is a generalization of those of Zener,4 Ham,5 and Horvay and cahn6 to the situation often encountered experimentally, in which the diffusion coefficient varies with concentration. First let us consider each of the cases separately. I) GROWTH OF SPHERICAL PARTICLES FROM ZERO SIZE In this case the differential equation in the matrix depends only on R, the radius in spherical coordinates, and can be written: ? 1 <^\ ^13D . , dt U\dRz + R 3Rj + dR dR [ J where C is the composition, t is the time, and D is the diffusion coefficient which depends on c. The boundary conditions will be: c = c, at the moving interface in the matrix, c = c, at infinity in the matrix (and at t = 0, everywhere in the matrix), c = X, is the composition in the spherical particle. Each of the above compositions is assumed constant. In addition there is the flu condition at the moving interface which can be written: , dR0 ~/3c dt \dR/H =Ra where R,, which is a function of t, is the position of the moving interface. We make the substitution q = RI~ in [I] reducing this equation to: & - m - *ws) »i where we have written D = D,F(c) or simply D,F, and Do = D(c,). Thus F[c(q0)] = 1 where q, = ~,/a is the value of the dimensionless parameter q evaluated at the interface. Multiplying Eq. [2] by dq/dc and integrating, we find: where the lower limit of the integral has been chosen so that dc/dq — 0 as c — c,, thereby satisfying the boundary condition at infinity. We require, then, to solve Eq. [3] subject to the condition c = c, when q = q, (this follows from putting R = R, at the interface) together with the flux condition which can be rewritten in terms of q as: Eqs. [3] and [4] together with the condition c = c, at q = q0 enable us to find 77, and the concentration profile c = c(q). Numerical Method. We treat Eq. [3] in the same way as we did the corresponding equation for the planar interface problem&apos; i.e., by dividing the interval c, to c, into n equal steps so that: cr = ca -rbc [5] where r takes the values 0, 1, ... n and we call no,, q1, ... nn the values of n corresponding to the compositions c,, c,, ... c,.

Jan 1, 1970

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus became citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil.

Jan 1, 1950

"Mining as an industry of Utah had its inception in the activities of United States soldiers who came to the Salt Lake valley under the command of Gen. P. E. Connor, founder of Fort Douglas, in October, 1862. Many of these soldiers were from California and naturally employed their spare time in the search for minerals. Although their military status did not permit them to make locations in their own names, they assiduously prospected the region in accordance with their own knowledge and with information conveyed to them by Indians and others. Their efforts were encouraged by their commander, who thereby fairly earned the title of father of the industry here, and by their other officers, and many discoveries that subsequently proved of great value were made by the soldiers.No systematic prospecting or mining had been done in the Territory previously, although early Mormon settlers in the southern portion had mined a little ore from time to time in order to provide supplies of lead for bullets. The Mormon leaders at that time did not encourage mining. They held that agriculture was more important and profitable for their followers.Coal was discovered and produced in 1850. Iron was discovered in 1850 and the first iron plant was in operation in 1852 in Iron County. The first non-ferrous metal production was in 1854, in Beaver County, when Isaac Grundy treated ore from the Rollins mine in what is said to have been the first lead furnace west of the Rocky Mountains. The first mineral location was the West Jordan claim in Bingham canyon, located September 17, 1863, now owned by the United States Smelting, Refining & Mining Co., and still productive. The first district organized in the state was the West Mountain (Bingham), December I 7, 1863. Other important districts of early organization are: Little Cottonwood, December 20, 1869; Big Cottonwood, July 11, 1870; American Fork, July 21, 1870; Uintah (Park City), July 8, 1871; Tintic, December 13, 1896; Ophir, August 6, 1870. The first silver-lead smelting was by J. W. Gibson at Stockton in 1866. Lieut. James Finnerty had previously erected two small trial furnaces there, but made no quantity production."

Jan 1, 1925

By W. M. Weigel

LESS advances in the technology of non-metallic minerals than for several years past mark 1931, and the cause is easily found. The universal depression and decreased markets for non-metallic as well as other mineral commodities has forced the producers to cut out all unnecessary expense and reduce operating costs to a minimum in order to keep going, even on a reduced output, and to prevent insolvency. The result. has been that but &apos;little research has been carried on, and such as has been completed has in but few cases been put into commercial practice on account of the expense involved in new equipment and plant changes. The trend in the industry has been more economic than technologic, and the greatest effort put on market studies and sales attempts to expand markets and scrutiny of present operating &apos;practice leading to reduction of cost of production. This tendency has been increased by highly competitive conditions and the buyer&apos;s market which has prevailed and to the fact that price has been a greater factor than quality in placing orders. Only in cases where improvements in technology would immediately and effectively reduce costs or where in special cases there was but little competition with almost a monopoly control has actual technical development taken place.

Jan 1, 1932

By S. G. Cupschalk, F. A. Dahlman, J. J. Wert

Studies have been undertaken to determine the indicidual effects of particle size, degree of long-range ovder, antiphase domain size, and root mean square stran on the microhardness and yield strength of ordered alloys. Dnta have been analyzed for Cu3Pt initzally ordered to a value of 0.82 and after deformations of 1 and 6 pct. It was observed that deformation fleatly reduced the degree of long-range order. Furtherrnore, wztkin this range of relatively small deforntntlons, the average particle size changed very little while the antiphase domain size was greatly reduced. Smultaneosly, the mcrohardness changed by a factor of two durzng the deforrtation process. PREVIOUS studies have reported some of the effects of cold work on the broadening of X-ray diffraction peaks. These investigations were performed on powder and wire samples representing both ordered and disordered states; i.e., the specimens were initially studied in a severly cold-worked condition. By comparing the difference in line shape between the annealed and cold-worked peaks, fundamental information was obtained concerning particle size, strain distribution in different crystallographic directions, degree of long-range order, and change in antiphase domain size. Considerable theoretical work has been done concerning the analysis of diffraction data obtained from cold-worked metals. Stokes&apos; expressed the change in diffraction profiles in terms of Fourier coefficients. Much of the work in this area has been summarized by warren2 in an extensive review article concerning the analysis of plastic deformation by X-ray diffraction. Cohen and Bever3 applied these techniques in studying the effects of cold work on alloy systems exhibiting long-range order. They utilized the Fourier coefficients of fundamental peaks in conjunction with those of the superlattice peaks to determine the change in antiphase domain size. Little work of this nature has been reported for ordered systems that have undergone small degrees of plastic deformation. The purpose of this investiga-tion was to determine the effects of small deformations in such a material with respect to particle size, strain distribution in various crystallographic directions, antiphase domain size, degree of long-range order, and hardness. EXPERIMENTAL PROCEDURE CusPt was used for the initial investigation since the order-disorder transformation takes place with- out a change in crystal structure. The transformation is readily detectable via X-ray diffraction techniques due to the large difference in the scattering factors of copper and platinum. Additionally, the alloy is relatively low melting (approximately 1300°C) and is easily deformable in both the ordered and disordered states. 1) Specimen Preparation and Cold Working. A 100-g, 12-in. diam., cylindrical specimen of Cu3Pt was prepared by melting and casting 99.99 pct pure Cu and Pt i.n vacuo. Prior to any mechanical working, the material was homogenized in a vacuum for 60 hr at 100O0C, and surface defects were removed by machining to a depth of approximately 116 of an in. The material was then cold-rolled, with an intermediate anneal, into a strip approximately 12 in. wide by 14 in. thick. Straightening and flattening removed another 0.025 in. from the thickness. After a recrystallization treatment at 750°C for 30 min, the specimen was slow-cooled from 55OoC, at the rate of 6°C per hr, down to 150°C to induce superlattice formation. This treatment yielded an ASTM grain size of 7 and a degree of long-range order equal to 0.83 0.06. After obtaining X-ray and Knoop hardness data, the sample was cold-rolled approximately 0.75 pct in one pass through a hand-operated jewelers&apos; mill. X-ray and hardness data were again obtained and the specimen was reduced an additional 5.41 pct in a single pass through the mill. 2) X-Ray Measurements. The specimen was examined in the ordered condition and after the two degrees of cold working previously mentioned using a General Electric XRD-5 unit equipped with a spectrometer and scintillation counter. Using Mo-Ka radiation with a zirconium filter, six orders of the 100 reflection were obtained. It was anticipated that point counting would be necessary for an accurate determination of the low-intensity peaks and tails: however, it was demonstrated that, by using a scanning speed of 0.2 deg per min and the appropriate time constant, the recorded data were sufficiently accurate. Thus, for ease of experimental procedure, all peaks were recorded on chart paper. Specimen position in the holder was considered to be insignificant after making a series of measurements of the same peak area in different positions with respect to the beam. Since peak overlapping did occur at high values of 20, it was necessary to separate the peaks graphically prior to analyzing the data in order to minimize this source of error. The peak tails were also carefully drawn to obtain the best possible data. Fourier coefficients of the line profiles were calculated on an IBM 7072 computer, and graphical meth-ods2j3 were employed in analyzing the results. For this type of calculation, in which the line profile is represented by intensities taken at set intervals, the intervals selected must be sufficiently small to give an accurate representation of the line profile. It was decided that for 20 = 0.02 deg the line profiles were

Jan 1, 1967

Callow, John M. Notes on Flotation. Discussed by R. H. Richards, Joseph W. Richards, Leonard Waldo, George Van Arsdale. 881 Horwood, E. J. Broken Hill Underground Mining Methods. Discussed by Albert R. Ledoux, W. L. Saunders 885 Lindgren, Waldemar, and Ross, Clyde P. The Iron Deposits of Daiquiri, Cuba. Discussed by Waldemar Lindgren, Max Roesler, Benjamin B. Lawrence, Louis C. Graton, Harrison Souder, Charles P. Berkey, Alfred C. Lane, John D. Irving. 886 Powers, Sidney and Lane, Alfred C. Magmatic Differentiation in Effusive Rocks. Discussed by N. L. Bowen, Alfred C. Lane, Sidney Powers 893 Tolman, C. F. Observations on Certain Types of Chalcocite and Their Characteristic Etch Patterns. Discussed by Louis C. Graton, Alfred C. Lane, Joseph T. Singewald, Jr., Charles P. Berkey, E. Posnjak, E. T. Allen, H. F. Merwin, C. F. Tolman, Jr. 895 Warren, H. M., Biesecker, A. S., and Powell, E. J. Tests on Various Motor-Driven Equipment Used in the Preparation of Anthracite Coal. Discussed by R. V. Morris, William Kent. H. M. Warren. K. A. Pauly 901

Jan 5, 1916