Search Documents

By Joachim J. Hauser

William F. Hosford, Jr. (Massachusetts Institute of Technology)—Dr. Hauser has used a very interesting method to study the interaction of dislocations on different slip systems, but it should be pointed out that the analysis of the experiments is subject to a serious criticism. He states that "the effect of the compression can be adequately described by one slip system." The effect of frictional constraint during the compression makes this quite unlikely. When a block of metal is compressed its lateral expansion requires a sliding of the metal over the compression platens. The role of friction in the interface between the deforming metal and the platens is to increase the normal force required for the compression. Analyses1213 have shown that, in general, the additional force, p, required for the compression is a function of l/h where is the coefficient of friction, I is the length of the speci- men in contact with the platens. For a constant COefficient of friction, isho' shows that P should increase exponentially with pl/h for both plane strain and axially symmetric compression. For a compression specimen, Fig. 7, whose cross section perpendicular to the compression axis is a rectangle whith one dimension L, much larger than the other W, a much larger force would be required for appreciable flow parallel to L than for flow parallel to U7. Therefore lateral strain in the W direction, EW, should be much greater than the lateral strain in the L direction EL. Since L/H = 14.5 for Dr. Hauser's crystals, and since no lubrication was used, it seems questionable that appreciable lengthening of the crystals could occur. Because the theories of frictional constraint have been derived for isotropic polycrystalline materials, it was decided to make experimental measurements on a single crystal. A section 3.590 in. long was sawed from an aluminum single crystal with a square section of 0.249 in., so that L/W= 14.4. This crystal was tested in compression between dry ground steel platens. Fig. 8 shows the orientation of the crystal and the axis of compression. The face for compression was chosen so that the operation of the single-slip system which would be predicted in the absence of friction would lead to a larger strain in the length direction than in the width direction. The dimensional changes of the width and length as well as the height were measured frequently during the compression with micrometers. Width strains were calculated from the average of readings near each end and at the center. A plot of the length strain, EL, against the width strain E w is given in Fig. 9. The slope indicates that the EL amounted to only 2.5 pct of cw. Other compression tests on similar crystals with shorter lengths also showed severely limited elongation. Even for a crystal with L/W = A.0, EL was only about 26 pct of cw. Because of the frequent interruptions of the tests for dimensional measurements should have decreased the frictional constraint by allowing a reseating of the platens, even smaller elongations under continuous testing seem probable. These tests on long narrow crystals show that essentially plane strain conditions prevailed. We may assume that Dr. Hauser's crystals deformed similarly. That the compression can be described by the

Jan 1, 1962

By E. Mille, R. Geffken

The Mg-Si and Mg-Ge phase diagrams were rede-levtnined by thermal analysis, and the existence of a single congruent melting compound in each system was confirmed. The melting points of the two compounds Mg2Ge and ,Wg2Si were found to be 1117.4° and 1085.0°C respectively. The euteclics for the Mg-Ge system occur at 635.6°C (1.15 at. pcl Ge) and 696. 7°C (64.3 at. pct Ge); for the Mg-Si system the eutectics are at 6376°C (1.16 at. pct Si) and 945.6°C (53.0 al. pcl Si). The phase diagrams and known thermodynamic data were used to calculate activity values for both systems. The activities calculated for the Mg-Ge system agreed very well with those previously published. Partial molar enthalpy values for the Mg-Si systetn were calculated from the phase diagram for the composition region where no experimental values have been reported. THE phase diagram for any system is an important source of thermodynamic data. Steiner, Miller, and Komarek1 have derived equations which permit calculation of the activity in binary systems with an inter-metallic compound! if the liquidus and enthalpy data are known. The thermodynamic properties of the Mg-Ge and Mg-Si systems have recently been determined in this by by an isopiestic method, and it was considered that it would be interesting to compare these directly determined values with those computed from the phase diagram. The basic features of the Mg-Ge and Mg-Si systems are essentially similar. The one intermediate compound present in each system. Mg2X, crystallizes in the antifluorite structure and melts congruently. Raynor4 has accurately determined the temperature and composition of the magnesium-rich eutectic in both the Mg-Ge and Mg-Si systems. Klemm and West-linning5 investigated the entire Mg-Ge liquidus, employing sintered alumina crucibles; the purity of the magnesium and germanium starting materials was not reported. The melt was not stirred, and the temperature was automatically recorded to an accuracy of ±3°C. The authors reported large weight changes due to magnesium evaporation between 50 and 67 at. pct Mg. The Mg-Si system has been studied by a number of investigators, and the results have been compiled by Hansen and Anderko.6 Significant discrepancies exist between the two principle investigations of voge17 and Wohler and Schliephake.8 Two different grades of silicon were used by Vogel, one of 99.2 pct purity and the other quite impure, containing 6 pct Fe and 1.7 pct Al. The magnesium purity was not specified. The melts were contained in graphite crucibles with porcelain thermocouple protection tubes under an atmosphere of hydrogen. Samples weighing 10 g were rapidly heated to 50° to 100°C above the liquidus: held, and then rapidly cooled without stirring. Accuracy was ±1 at. pct which is equivalent to a maximum error in temperature of ±18°C. Wohler and Schliephake used 97.9 pct Mg and 99.48 pct Si. The graphite crucibles contained a stirrer and the 15-g samples were melted under an atmosphere of streaming hydrogen. The samples were chemically analyzed after each run. Because of the scarcity of the data, the impurity of the starting materials, and the resultant uncertainty and inconsistency in the published liquidus values, it was decided to undertake a reevaluation of the Mg-Ge and Mg-Si phase diagrams by thermal analysis. EXPERIMENTAL PROCEDURE Alloys were prepared from 99.99+ pct Mg (Dominion Magnesium Ltd.) with impurities in ppm: 20 Al, 30 Zn, 10 Si, <1 Ni, <1 Cu. <10 Fe; 99.999 pct Ge (United Mineral and Chemical Corp.), and 99.999 pct Si (Wacker Chemie Corp.). All graphite parts were machined from high-density (1.89 g per cu cm) G-grade graphite obtained from Basic Carbon Corp. with a total ash content of 0.04 pct. Boron nitride parts were machined from rods of National-grade H.B.N. boron nitride. All graphite and boron nitride pieces were baked out under running vacuum at 1100°C for 24 hr before us Cylindrical graphite crucibles (1; in. OD, 23/4 in. long, l3/8 in. ID) were tightly closed with threaded graphite covers which had 21/4-in.-long thermocouple wells and 1/4-in.-diam off-center holes for stirrers. The cover and thermocouple well were machined from a single piece of graphite. A stirrer was made from a flat cylindrical graphite plate perforated with five 3/16-in.-diam holes and a 1/2-in.-diam central hole, and was held parallel to the crucible bottom by a 1/4-in.-diam. 4-in.-long graphite rod which screwed into the plate and extended up through a tightly fitting hole in the crucible cover. An iron core enclosed in a glass capsule was attached to the stirrer with an 18-in.-long molybdenum wire, so that the stirrer could be magnetically raised and lowered from outside the system. One crucible and stirrer with essentially the same dimensions given above was made entirely of boron nitride. Chunks of magnesium were premelted, cast into 11/2-in.-diam. rods, and then cut into lengths varying from a to 1 in. A 5/16-in. hole was drilled through the center of each piece to accommodate the thermocouple well and the individual pieces were then cleaned and rinsed with acetone. The total weight of an alloy was 50 to 70 g in the Mg-Ge system and 40 to 60 g in the Mg-Si system. The pure components were weighed to an accuracy

Jan 1, 1969

By Bedrand L. Johnson

THE phosphate-rock industry is built upon natural deposits of rocks and minerals in which the element phosphorus is present as a phoshate. The term ?phosphate rock? is a general one, applied to certain rocks of different degrees of consolidation and of diverese origin, charater and occurrence, composed of intimate mixtures of several phosphate minerals, largely submicrocrystalline, usually calcium phosphates, in commerical quantities, with various impurities. This term includes phosphatized limestones, sandstone, shales, and igneous rocks; nodular phosphates ; residual weathered phosphatic limestones ; vein phosphates ; and phosphatic sediments, both consolidated and unconsolidated.

Jan 1, 1944

By D. S. Sanders

IN the four mills of the Cerro de Pasco Copper Corp. in Peru, some 3000 tons of complex sulphide ores are treated daily, with four kinds of concentrates produced: copper, lead, zinc, and pyrite, each containing values in silver, gold, bismuth, and some other metals. Copper occurs in the various ores as chalcopyrite, enargite, tetrahedrite, tenantite, bournonite, and chalcocite; lead as galena; and zinc as sphalerite and marmatite. Small amounts of silver and tungsten minerals are also present. The gangue consist mainly of shale, quartzite, calcite, rhodochrosite, pyrite, and pyrrhotite. In general the values are freed with a relatively coarse grind, about 70 prr cent minus 200 mesh being the finest to which the pulps are ground. In Morococha and Casapalca however. sphalerite particles much finer than this contain inclusions of chalcopyrit r. At Cerro de Pasco the silver and gold are present in all sizes of the ground pyrite.

Jan 1, 1945

By C. D. Demond

In reverberatory smelting, fuel is the chief item of expense, as it commonly is in processes using large percentages of it. Hence the most suitable supply is eagerly sought; that is, the supply which, in the end, yields the greatest net profit. The better grades are not infrequently bought, even at an advanced price, because they are apt to be decidedly more economical. High price, of itself, however, is no merit, for freight is generally the largest part of the cost of fuel, and the nearby supply may yield as high efficiency as that from a greater distance. If a poorer grade is reasonably good, and if its cost is low enough to more than offset the decreased technical efficiency, it is of course the more suitable. Any smelting operation depends for both efficiency and economy on raising the furnace atmosphere considerably above the "critical" temperature; that is, above the temperature at which smelting is completed. If this temperature is not exceeded, smelting stops, no matter how much coal is burned; and the real value of a fuel depends on the number of degrees that the temperature is continuously kept above this point. For example, if one fuel maintains 2,500" F. and another only 2,100 F., while the "critical" temperature is 2,000" F., the first is worth at least five times as much as the second, although the increase above atmospheric temperature is only one-fifth more in one case than in the other. This "margin of temperature" above the smelting point is much more significant than the total number of heat units developed from the fuel. The case is parallel to that of water flowing from a pipe. The reservoir may contain a billion gallons of water; but, even though the fluid has come to the nozzle, not a drop will run out, where it can be of practical use, unless the level in the reservoir is higher than the nozzle; and the speed and volume of flow depend on how much higher the level is in the reservoir than at this point. If the temperature in a furnace is not above the critical level there will be no slag to flow over the skimming plate, even though there are enough heat units to bring an unlimited quantity of charge up to the point of slag formation; and just as the value of a water supply for the purpose of putting out a fire depends largely on the effective head, so the difficulties of furnace management

Jan 1, 1915

By W. A. Ver Wiebe

Spurred on by the very high demands for new crude supplies resulting from World War 11, the oil men of Kansas strained every effort in 1943 to find as many new pools as possible. In all, 1761 test wells were drilled, ,of which 895 were successful in finding new oil supplies and 32 in finding new gas supplies. The total number of wildcat wells drilled in Kansas was 577, including the so-called "extension wildcats," which are located less than 2 miles from production. As a result of the very determined effort to find new oil reserves, 49 of the wildcat test wells found new oil pools in western Kansas and 7 found new oil pools in eastern Kansas. There were 289 rank wildcat tests, and among these 28 were successful ventures. They are responsible for 26 of the new oil pools recorded for the year and 2 of the new gas pools recorded. The ratio of dry holes to producing wells among such rank wildcats is thus approximately 10 to I (289 dry and 28 good). This compares with a ratio of II: I in 1942 and 6:1 in 1941; the same in 1940 and 5:Iin 1939. With nearly all wells flowing to their maximum economic capacity, the total production for Kansas during 1943 reached a new high; that is, 107,700,000 bbl., compared with 97,000,000 during the previous year. Similarly, the amount of gas sold during 1943 made a new high point on the production curve. The total amount was 122 billion cubic feet, compared with about 98 1/2 billion cubic feet for the year previous. As usual, the large Hugoton field of south- western Kansas accounted for approximately half of the total gas production. Highlights of the Year Despite the fact that 56 new pools were found in Kansas during 1943, it must be admitted that the future reserves of the state have not been increased greatly. Most of the new pools seem to be of minor value, although it is admittedly impossible to gauge the future production of any pool in Kansas with any exactitude. Judging by the later performance of some of the pools found in 1942 and in 1941, less than five of the new pools are likely to make any great contribution to the state&apos;s future oil reserves. Taking up the counties of Kansas in alphabetical order, the following statements summarize the highlights of the year. In Graham County, the Morel pool was extended to the southeast and this pool now promises to become one of the important pools of western Kansas. Several of the older wells have already contributed more than I000,000 bbl. of oil, and such a figure is considered very satisfactory in Kansas. In McPherson County, important new reserves were found by persistent drilling in township 17 S., R. I. W., the most northeastern township of the county. Many new wells in older pools and discovery wells in new pools make this region look promising. The Lindsborg pool, which had a sensational revival during 1942, was also extended in a number of directions and has now become a rather large producing area with a fairly high future potential capacity.

Jan 1, 1944

By W. A. Ver Wiebe

Spurred on by the very high demands for new crude supplies resulting from World War 11, the oil men of Kansas strained every effort in 1943 to find as many new pools as possible. In all, 1761 test wells were drilled, ,of which 895 were successful in finding new oil supplies and 32 in finding new gas supplies. The total number of wildcat wells drilled in Kansas was 577, including the so-called "extension wildcats," which are located less than 2 miles from production. As a result of the very determined effort to find new oil reserves, 49 of the wildcat test wells found new oil pools in western Kansas and 7 found new oil pools in eastern Kansas. There were 289 rank wildcat tests, and among these 28 were successful ventures. They are responsible for 26 of the new oil pools recorded for the year and 2 of the new gas pools recorded. The ratio of dry holes to producing wells among such rank wildcats is thus approximately 10 to I (289 dry and 28 good). This compares with a ratio of II: I in 1942 and 6:1 in 1941; the same in 1940 and 5:Iin 1939. With nearly all wells flowing to their maximum economic capacity, the total production for Kansas during 1943 reached a new high; that is, 107,700,000 bbl., compared with 97,000,000 during the previous year. Similarly, the amount of gas sold during 1943 made a new high point on the production curve. The total amount was 122 billion cubic feet, compared with about 98 1/2 billion cubic feet for the year previous. As usual, the large Hugoton field of south- western Kansas accounted for approximately half of the total gas production. Highlights of the Year Despite the fact that 56 new pools were found in Kansas during 1943, it must be admitted that the future reserves of the state have not been increased greatly. Most of the new pools seem to be of minor value, although it is admittedly impossible to gauge the future production of any pool in Kansas with any exactitude. Judging by the later performance of some of the pools found in 1942 and in 1941, less than five of the new pools are likely to make any great contribution to the state&apos;s future oil reserves. Taking up the counties of Kansas in alphabetical order, the following statements summarize the highlights of the year. In Graham County, the Morel pool was extended to the southeast and this pool now promises to become one of the important pools of western Kansas. Several of the older wells have already contributed more than I000,000 bbl. of oil, and such a figure is considered very satisfactory in Kansas. In McPherson County, important new reserves were found by persistent drilling in township 17 S., R. I. W., the most northeastern township of the county. Many new wells in older pools and discovery wells in new pools make this region look promising. The Lindsborg pool, which had a sensational revival during 1942, was also extended in a number of directions and has now become a rather large producing area with a fairly high future potential capacity.

Jan 1, 1944

By A. E. Dwight, Paul A. Beck

Known CsCl-type phases in transition metal alloys are shown to be formed preferentially at an electron concentration of approximately 6; a tetragonally distorted version of the CsCl structure is stable at -e/a = 6.5. The relationship of the distortion to electron concentration is verified by experimental data for the quasibinary systems Time ,Os) , Ti(Re,Ir), and Ti(Re,Pt) and the ternary system Ti-Ru-Rh. It was noted some years ago1j2 that the occurrence of CsC1-type ordered structures in equiatomic binary alloys, AB, of transition metals correlates with the location of the component elements in the periodic table. One of the components, A, must be to the left and the other component. B, must be to the right of the chromium group. It was pointed out2 that the CsCl structure does not occur in CrFe. is metastable in VFe,3 and is stable in TiFe up to high temperatures, and that this progressively increasing stability may correspond to an increase in electron transfer between the two components and to a correlated decrease of the magnetic moment associated with the iron atoms. Such a decrease was in fact later demonstrated by Nevitt. 4 The binary CsC1-type phases that are formed by a transition metal with either another transition metal or a lanthanide are listed in Table I. Thirty-three of these phases occur at an average electron concentration (average number of electrons outside of closed shells) of e/a = 6. The five phases that are formed at an electron concentration of e/a = 5.5 appear to be borderline cases. This is suggested for instance by the fact that TiRe is bcc. without any long-range order, while TiTc (at the same electron concentration) has a CsCl ordered structure. Six of the undistorted CsCl phases formed by transition metals with one another have an average electron concentration of e/a = 6. 5. Table I. With the exception of Zr4,Rhs4 and Hf48Rh52. the B component in these phases is a first long-period transition metal, i.e.. iron or cobalt. TiNi. with an electron concentration of e/n = 7, appears to undergo transformation at around room temperature to a more complex ordered struct~re.~ The five other CsCl structures known to occur at e/a = 6.5 have either scandium or a lanthanide metal as the A component; the difference in the elec-tronegativity and in the e/a ratio between the component elements is in these phases very large, A(e/a) - 7, and they may be expected to have a rather strong ionic bond component. Presumably the ionic bond stabilizes the CsCl-type structure at the equiatomic composition and it overrides the electron concentration requirement. When the B element is not from the first long period and the A component is not a rare earth metal. equiatomic (AB) alloys of transition metals with an average electron concentration of e/a = 6.5 in most cases have a crystal structure closely related to the CsC1-type, but slightly distorted tetragonally, Table I. This was first found6 for VRu, NbRu. and TaRu. It was noted6 that the undistorted CsCl structure is also stable in the three systems. but at a lower electron concentration, near e/a = 6. In these systems this requires a deviation from equiatomic stoichiometry. which is otherwise ideally suited for the CsC1-type structure. A similar situation was later found in the Ti-Rh7 and the Ti-Ir systems. 8 The Ti-Rh alloys undergo a second distortion and become orthorhombic when the rhodium content becomes somewhat larger than 50 pct. As mentioned previously. TiRe does not have the CsC1-type ordered structure. In order to investigate how close TiRe is to the borderline of stability of the

Jan 1, 1970

By J. Laskowski

J. Laskowski (Associate Professor, Dept, of Mineral Processing and Coal Preparation, Silesian University of Technology, Gliwice, Poland) -Referring to the papers by J. A. L. Campbell and S. C. Sun, I must say that I am very pleased to see that type of work, because it is the only way to progress towards an understanding of flotation mechanisms. All those interested in the science of the surface chemistry of coals would find these papers a valuable contribution to the literature. In their extensive research, the authors attempt to synthesize their findings into a theory of coal flotation. To do this, the zeta potential of bituminous coals and their lithotypes, as well as that of an anthracite coal, was measured and H+ and OH- ions were found to be potential determining ions. The measured ZPC of bituminous coals was at a pH range from 3.5 to 4.6 and for the anthracites between 2.0 and 4.5. The authors have pointed out that since the hydrophobicity is pH-controlled, the flotation mechanism should also be. The Campbell and Sun papers confirm a good many of the conclusions on surface properties of coals reported in recent years. It is noteworthy to point out that the ZPC found in the paper on bituminous coals was approximately pH 4, similar to the ZPC for the anthracite coal. In fact, we have been investigating different coals from low to high ranks. Thus, the plot of the pH for ZPC against rank could be derived and this curve-an electrocapillary one-indicates a pH near which the hydrophobicity of the coal surface should be at maximum. This can be proved by so-called salt flotation, which, in a sense, can be treated as method of surface charge measurement. It is obvious that the salt flotation experiment is possible when the native hydrophobicity of the mineral surface is high, e.g., when the solid surface does not have an orienting influence on an adjacent water layer and the hydration layers are controlled by the electrical double-layer potential. The addition of electrolyte or a change of pH which decreases the thickness of the stabilizing double-layer "opens up" the hydrophobic surface micro-area mosaic. Thereby the surface becomes hydrophobic and particles become floatable. The orienting influence of surface on hydration layer increases even after very slight oxidation and flotation is affected by it. It seems that such an explanation agrees reasonably well with those of Campbell and Sun.

Jan 1, 1972

By David Moskowitz, Ira Binder, Robert Steinitz

THE hard refractory borides of the transition elements of the 4th, 5th, and 6th groups of the Periodic System have been the subject of a number of recent investigations.&apos;-&apos; It is well known now that most of these elements form several different borides, and Kiessling8 has summarized the rules which govern to some extent the arrangements of the boron atoms in the various structures. Melting points of a few borides have been published." The systems Fe-B, Ni-B, and Co-B have been reported," but, as these borides are rather low melting, they are outside of the groups of boron compounds considered here. Brewer&apos; has tested the stability of various borides and estimated a number of eutectic temperatures between different borides, but in no case was the complete system of a transition metal and boron investigated. The phase diagram becomes of special importance if the preparation of the borides from the elements in powdered form is considered; the lowest eutectic temperature will determine the first appearance of a liquid phase. Also, the knowledge of high temperature phases, if they exist, is important for the preparation of bodies from these borides by hot pressing or sintering. During the investigation of various metal borides,7 it was found that there were more boride phases existing in the Mo-B system than reported by Kiessling." They occur, however, only at temperatures above 1500°C and were, therefore, not found by him. This led to a study of the equilibrium diagram of the Mo-B system. ranging from 0 to 25 pct B and from room temperature to the liquidus. Part of this investigation was reported during the "Research in Progress" session at the 1952 Annual Meeting of the AIME.11 Raw Materials and Preparation of the Borides The raw materials used were commercial molybdenum and boron powder, both supplied by the Molybdenum Corp. of America. The molybdenum powder was 99+ pct pure? while the boron powder contained about 83 to 85 pct B. A large percentage of the impurities in this powder was oxygen, with the rest formed by iron, calcium, and unknown substances. The low purity of the boron used was, however, not considered detrimental to the final product, as most of the impurities evaporated at the high temperatures at which the borides were formed. The final product always had a minimum purity of 96 to 98 pct (figured as molybdenum and boron), with carbon, iron, and probably oxygen being the remaining products. Carbon is usually present as graphite. The chemical analyses always confirmed the compositions which corresponded to the crystallographic structures as determined by X-ray diffraction, and the boron content of the finished product agreed closely with that of the starting mixture; no boron was lost during the boride preparation. The chemical analysis methods employed for molybdenum and boron were previously described by Blumenthal.12,13 The powders were mixed by hand in the desired proportions, compressed at room temperature under low pressure, and then heated under hydrogen to about 1500" to 1700°C in a graphite crucible to form the borides. Usually, the three well-known borides Mo,B, MOB, and Mo,B,, which are stable at room temperatures, were prepared in this way, and all other compositions were made by mixing these borides in various ratios or by the addition of molybdenum or boron powders for the very low or very high boron contents. Preparation of two-phase compositions directly from the elemental powders was tried only occasionally to check whether equilibrium could be reached in this way. Experimental Procedures The stable borides were mixed in the desired ratios and heated under hydrogen in graphite crucibles to various temperatures. The well insulated crucibles were heated in a high frequency induction furnace. Special care was taken to obtain exact temperature measurement, which proved much more difficult than originally anticipated. It is believed that individual temperature measurements have an error of less than ±25ºC, while melting or transformation temperatures are accurate within ±50°C. The temperatures were measured with an optical pyrometer which was aimed at the closed end of a graphite tube extending down into the crucible. close to the samples. Attempts to measure directly through the hydrogen exit stack failed. The crucible arrangement is shown in Fig. 1. Heating was done at a slow rate to be sure that the temperature inside the crucible was uniform. The specimens were kept at the final temperature for about 30 min. For the investigation of high temperature phases, some samples were quenched. They were heated, without atmosphere protection, in a very small graphite crucible which could be rapidly removed from the high frequency coil, and dropped into water. These quenched samples were afterwards annealed to establish the equilibrium at lower temperatures. The melting points or the positions of the solidus and liquidus lines were determined by heating the specimens to various temperatures and examining them at room temperature for evidence of a liquid phase. These results were checked later on by thermal arrest curves, especially to determine the exact position of the eutectic temperature line. For this purpose about 200 g of the boride were melted in a graphite crucible, in an arrangement similar to Fig. 1. Slow cooling was assured by very good

Jan 1, 1953

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct alloy content were carefully resolved. Phase relationships in the higher alloy content regions were outlined. A single intermediate phase, peritectically formed, of the form ZrX2 was established in each system. A eutectic and a eutectoid were found in the zirconium-rich region of both systems. Appreciable solubility of molybdenum and wolfram was found in ß zirconium, but only a slight solubility in a zirconium. PREVIOUS work on these systems was limited to X-ray investigations of the intermediate phases1, 2 and preliminary surveys of the zirconium-rich alloys." The diagrams presented were determined principally by metallographic, thermal analysis, and incipient melting techniques. In accordance with the Atomic Energy Commission contract requirements, phase relationships up to 50 atomic pct molybdenum or wolfram were carefully resolved, while only a limited amount of work was done to outline the 50 to 100 atomic pct alloy region. A description and analysis of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar, produced by the decomposition of a volatile iodide onto a hot filament, was employed for these studies. Westinghouse "Grade 3" crystal bar was used for all alloys. The zirconium, as received, was coated with corrosion product from a standard autoclave test by which its grade designation is determined. This was removed by a sand-blasting and HF-HNO, pickling technique developed by the Atomic Energy Commission. The bars were cold rolled to approximately 1/32 in. sheet, pickled for iron removal, sheared to 1/4 in. squares, washed with acetone, and stored for furnace charge. Molybdenum sheet. 0.003 in. thick, 0.001 to 0.005 in. wolfram wire, and M in. wolfram rod crushed to granular form, from Fansteel Metallurgical Corp., were used as alloying stock. Melting Procedure A nonconsumable electrode arc furnace identical to that described in detail by Hansen et al.4 was used. The source of power for melting Zr-Mo alloys was a 400 amp dc welding generator, while a 900 amp dc generator was used for preparing Zr-W alloys. Electrode tips of the same material as the alloy addition were employed in both systems, i.e., molybdenum tips were used for Zr-Mo alloys, and wolfram tips for Zr-W alloys. This precluded any possible electrode contamination during arc melting. Ingots of 20 to 30 g of Zr-Mo alloys were melted under high purity helium in the cavity of a copper block insert in a spun copper crucible. Homogeneity was insured by remelting all ingots four to six times without opening the furnace. Due to the large difference between the melting points of wolfram and zirconium, direct melting of the charged metals as above generally yielded ingots containing unmelted wolfram particles. This was overcome, after many variations in technique, by melting a pure wolfram charge at high power levels (700 to 900 amp) and slowly adding zirconium to form a master alloy. Such master alloys were sectioned and remelted several times, then crushed to serve as melting stock for alloys of lower wolfram content. Master alloys containing 26, 50, 52, 70, and

Jan 1, 1954

By H. Evans, L. A. Hunt

In the pellet-producing industry it is sometimes claimed that "The pellets are made in the concentrator," or that "The key to good pellets is in the balling operation." However, one claim is generally agreed on: If you can put in, on, and through the indurating furnace a good green ball of Proper size and adequate strength to withstand the handling, load, dehydration, and thermal shock until it is properly heat-hardened, you will have the pellet product you desire-that is, a "competent" green ball. The strength requirements that enable a competent green ball to withstand the environment of the indurating furnace are usually less restrictive than those for transporting the green ball from its source of production to the furnace. Experience has shown that different types of material may have different balling characteristics which may impose limitations on the quality of the green ball that can easily be produced under normal conditions. Therefore, if a specific material will produce a green ball that meets the physical requirements for competency in the furnace, but not for handling or transportation, various practices must be instituted to overcome this deficiency. In other words, if a normal handling system is too rigorous for the green balls that can be produced under standard conditions, then "handling with care" should be tried.

Jan 5, 1967

By M. D. Hassialis

THE object of a technical paper is to communicate new technical knowledge, the paper being the vehicle of communication and the existence of new knowledge its reason for being. It follows that the development of information worthy of communication, the criterion being novelty, is prerequisite to exercising the privilege of communication. The act of communication is achieved when the reader perceives the nature of the new knowledge, i.e., when he understands it. A paper achieving this objective is an acceptable technical paper. Development of new knowledge has as one of its purposes the increase of the existing state of knowledge and the enjoyment of the benefits derived therefrom. Technical knowledge is a collection of facts so ordered as to make apparent, relations existing between the facts. When the interrelations have been exposed the facts have been interpreted or explained Three broad, overlapping categories of technical papers may be recognized: papers consisting of (a) a report of facts, (b) an explanation of facts, or (c) a combination of a report and an interpretation. Ideally a technical paper should belong to one of the last two categories but current practice is to accept papers belonging to any of the three categories. Based on a small sample drawn from the scientific and engineering literature, the relative frequency of the three types is a: b: c:: 20:1:14. If the sample be limited to engineering literature, the ratios become a:c::2:1; type (b) being nonexistent. This large departure from the ideal is a consequent of the

Jan 1, 1948

By Arthur Notman

IN VIEW of the wide publicity given to the charges by the Couzens Committee of the United States Senate of discrimination by the Bureau of Internal Revenue in favor of the copper companies, it becomes a matter of interest to consider the basis for these charges. The point to be determined is whether they rest on a foundation of fact or are purely and simply matters of opinion. The whole question boils down to the purpose of the Tax Law as applied to mines, which is to afford the same protection to them as provided for all other taxpayers, namely: that they were to be allowed to pay back as depletion to their owners the values of their properties as they existed or were estimated to exist on May 1, 1913, free from tax. To determine these valuations it was? necessary to select from a wide range of possibilities a set of values for a number of essential factors.

Jan 1, 1925

By J. S. Owens, R. W. Marsden, J. W. Emanuelson, R. F. Werner, N. E. Walker

The iron ores of the Mesabi Range occur in a 340 to 750-foot thick, Precambrian cherty iron formation termed "taconite." For about 65 years, extensive natural iron ore bodies were mined, and the ores either shipped as a direct ore or processed by gravity methods to a shipping grade iron ore. Since 1956, magnetite taconite ores, occurring in magnetite-rich horizons in the Biwabik iron formation, have been commercially concentrated and agglomerated. The transition from natural ores to concentrating-grade ores is progressing rapidly so that, in the near future, a major percentage of the iron ore shipped from the Mesabi Range will be as iron ore pellets produced from taconite. Natural iron ores of the Mesabi Range occur in the Biwabik formation as trough ore bodies in elongated channels and as irregular and tabular deposits in fractured areas associated with faults and folds. Ore bodies range in size from a few thousand tons to hundreds of millions of tons and may occur in any part of the iron formation. In some areas of strong ore development, ore was formed from the hanging-wall argillite to the footwall quartzite. The natural ores and beneficiating-grade natural crude ores were formed by the oxidation of the iron minerals, magnetite, greenalite, stilpnomelane, minnesotaite, and siderite, to hematite and goethite and by the removal of much of the silica in the cherty quartz and in the associated silicates by leaching. The ores are believed to have formed by the oxidizing and leaching action of surface waters. Magnetite taconite ores occur as stratigraphic zones in the Biwabik formation where it contains sufficient magnetite to be concentrated profitably, by magnetic methods, to give a magnetite concentrate that is agglomerated into a high quality product. Unoxidized taconite has an extensive distribution away from and between channels of oxidation and leaching but only a part of the unoxidized taconite is of ore grade. Two general types of magnetite taconite ore occur: ( 1) magnetite taconite of the Main Mesabi Range, generally west of Mesaba, which is composed of magnetite associated with cherty quartz, greenalite, stilpnomelane, minnesotaite, and carbonates and (2) magnetite taconite of the Eastern Mesabi, generally east of Mesaba, composed of magnetite associated with quartz, cummingtonite, actinolite, ferrohypersthene, hedenbergite, fayalite, hornblende, pyroxene, garnet, and biotite. The Mesabi taconite is a metasediment derived from an iron- and silica-rich chemical sediment that has been regionally metamorphosed and, on the eastern end, additionally metamorphosed by the Duluth Gabbro Complex.

Jan 1, 1968

By David W. Brunton

FROM the old-fashioned " grab-sample " to the modern timing- . device, which takes a machine-sample with mathematical precision, there is a wide gap which was only crossed&apos; by many years of toil and unremitting endeavor. Even to-day, notwithstanding the advancement in the art, "grab-sampling" is still practiced-sometimes to afford the unscrupulous mine-promoter a basis for fairy-tales with which to entrap the too-gullible investor, and often by milling and smelting companies to determine the amount of moisture in custom-ores. The latter practice is almost as reprehensible as the former, and it causes more trouble and ill-feeling between seller and buyer than all other factors put together. No reputable concern to-day would think of attempting to determine by grab-sampling the amount of gold, silver, lead, or copper contained in an ore, and yet many buyers expect the miner to accept the results of grab-sampling in the determination of the amount of water contained in the ore, forgetting that accurate results are just as necessary here as in the determination of the metals, because the result determines the percentage of weight of the ore which shall be excluded and considered to have no value whatever. Samples for the determination of moisture should be taken with as great care as samples for the determination of. metallic content, and in order to avoid the extra expense of a separate operation moisture-samples should be taken from the sample-safe. As the sample reaches the sample-bin in a smaller stream and by a more circuitous route than the "reject" travels in its path to the outgoing car, it loses more moisture en route, and a constant should be added to compensate for this difference. Carefully-conducted experiments have shown that the difference in loss of moisture between the two routes does not exceed 10 per cent. in summer and 7 per cent.. in winter. For instance,

Aug 1, 1909

By Robert M. Weidenhammer

For years before the war, Coal had the reputation of being a sick industry. Currently it is operating at peak production and succeeding pretty well in keeping out of the red. But, says Mr. Weidenhammer, it will have a relapse as soon as the war ends unless (1) working capital can be built up; (2) it gets the support of the people and Congress; and (3) a truly long-range national fuel policy is formulated.

Jan 1, 1943

By S. Arthur Krom

(New York Meeting, February, 1912.) THE James diagonal-plane slimer is specially adapted to handle the finest slimes, but it will also handle sands as coarse as 40-mesh. The saving efficiency of this machine is due to the original construction of the deck, and to the rapid reciprocating movement imparted to it by the head-motion. The deck consists of a plurality of connected planes, having a certain fixed ratio of inclination one to another. These planes intersect each other diagonally to the stroke-line of the table and are arranged so as to give the pulp on the table a double treatment. This double concentration performed by the diagonal-plane deck produces cleaner concentrates and tailings than those obtained by the operation of two separate machines. The action of the diagonal planes settles, combines, and holds all the concentrates in one compact mass, sharply defined from the gangue, and easily cut away without loss. Many slime-concentrating machines distribute the feed-pulp for a distance of 4 or 5 ft. only, and upon a very limited settling-surface. This results in a thick, heavy deposit, from which it is impossible to stratify the values and wash, away the gangue, the resulting products being dirty concentrates, and tailings carrying high values. The diagonal-plane slimer distributes the feed-pulp for a distance of 10 ft., and upon a settling-surface having an area of 40 sq. ft.; in other words, it spreads the pulp thinly on the table, which allows the metallic values to settle through the gangue quickly, forming a bottom stratum from which the thinly-distributed overlying stratum. of gangue is easily brushed away by the feed-water without disturbing the underlying concentrates. Referring to Fig. 1, plane A is the main settling-section, of the table. The feed pulp flows gently down this plane and is

Jun 1, 1912

By R. M. Foley, Hidesaburo Kurushima

About 25 pct of all Japanese pyrite comes from the Yanahara mine on Honchu Island. For the past 40 years lack of an economical recovery process forced the operator, Dowa Mining Co., to sell the pyrite for its contained sulfur only, leaving 7 million tons of high grade iron ore waste. Introduction of the Dorrco FluoSolids roasting system enabled the company to make use of its iron sulfides and also to find a market for the mine&apos;s considerable pyrrhotite production. The success of this project is of great importance to Japan&apos;s economy since it points the way toward material increase in her natural resources. Prior to use of the present process, no practical method was available for commercial exploitation of known large tonnages of pyrrhotite, while the copper content of the even larger deposits of pyrite made the roasted residue unacceptable for the iron and steel industry. In Europe, large amounts of copper-bearing pyrite cinder are given a chloridizing roast for separation of the copper and iron but this treatment is not economical in Japan where salt is imported from as far away as Egypt.

Jan 10, 1958

The Mineral Industry, Published by McGraw-Hill Book Co, New York, N Y. The Mineral Industry is an annual review of the mineral industry It is a standard and complete reference on the mineral industry for the year covered Through the cooperation of the A I M E its publication in 1933 was made possible Mineral Industry for 1930 contains sections devoted to the production, consumption, trade, market, uses and technology of the following headings: Abrasives, aluminum and bauxite, antimony, arsenic, asbestos (b), asphalt, barium and strontium, chromium (b), coal and coke, cobalt (b), copper, diatomite, fluorspar, gold and silver, graphite, gypsum, iron and steel (b), lead, magnesite, manganese, mica, molybdenum, nickel, petroleum and petroleum products, phosphate rock (b), platinum group metals (b), potash, precious and semiprecious stones (b), quicksilver, radium (b), uranium and vanadium, slate (b), sodium salts, sulfur, pyrite, sulfuric acid, talc and soapstone, tin, titanium and zirconium, tungsten (b), zinc, minor metals, minor nonmetals, ore dressing and coal washing (b). Sections marked (b) have appended a bibliography of recent literature on the subject. Each section is written by an acknowledged expert. Other volumes contain similar material Prices -The Mineral Industry, 1892-1930, vols. 1 to 39. Complete sets of this work, uniformly bound, except vols 25 and 26,

Jan 1, 1933