Search Documents

By F. G. Smith

A FEW years ago, the writer encountered a, problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Matthewson and Phillips, an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-inn. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures.

Jan 8, 1919

By George A. Miller

ALTHOUGH the Andean mountain belt, which contains almost all the metal deposits of the other South American nations, does not enter Brazil, this country is rich in mineral resources, for in area it accounts for half the continent and geologically it contains almost all of the Brazilian Shield. This great mass of ancient rocks has been relatively stable for a long time and forms a great area of plateaus and highlands interrupted only by the syncline which carries the Amazon River across it to the sea. Lowland Brazil - the great flood plains of the Amazon. Tocantins, Paraguay, and Parana Rivers-is of no interest to the miner, and in fact supports but a small proportion of the country's population. The highland area is divided into unequal parts by the Amazon River; the north half is underlain by the north lobe of the Brazilian Shield which extends into Venezuela as far as the Orinoco, and into the Guianas, and is known as the Guiana Highlands. Mineralization appears to have been weak in the Brazilian portion of these hills. In fact most of the ore deposits are to be found in the States of Minas Gerais and Bahia, although the neighboring states of Sao Paulo, Pernambuco, and Piauhy can also boast of some deposits. Goias and Matto Grosso are as yet incompletely prospected but are considered to contain reserves for the future.

Jan 1, 1945

By R. H. Maes, R. E. de Strycker, J. J. Jacobs

A simple method, based upow density measurements, has been perfected in order to determine the critical temperature of liquid miscibility gaps. Applied to the Pb-Cu system, it yielded a value of 980"C for the critical tempevature of the miscibility gap in this system. In the Pb-Cu-As system, the immiscibility between lead and coppev evolves towards a miscibility gap be-tween lead and copper arsenides; the liquation temperatures were determined joy different avsenic contents and values up to 1065°C were found. Combining these results with those given by the clzemical analysis of liquid samples taken at dqj.event temperatures, it has been possible to make a cowzplete determination of the liquid miscibility gap in this ternary system. In the Pb-Cu-Fe-As system, a ternary miscibility gap has been discovered; for some compositions, the molten and slowly cooled alloys separated into three layers: an Fe-As alloy, a Cu-As alloy, and a lead-rich layer. ThE Pb-Cu-Fe-As system is of interest for the study of the behavior of speiss or arsenical alloys in the lead blast furnace. The speisses produced in lead metallurgy generally have complex compositions, but they may be considered, in a simplified way, as a mixture of copper, iron, nickel, and cobalt arsenides; there is often an excess of metallic constituants, and lead is also present. Speisses liquate from lead at various temperatures according to their composition; according to industrial experience, iron speisses are already distinctly separated from lead bullion at temperatures of the order of 1100°C, whereas copper speisses only begin to liquate from lead at much lower temperatures, near their solidification points, which were never accurately determined until now. Besides these considerations of practical interest, the present study is of importance for the knowledge of liquid miscibility gaps. Particularly the data of the literature about critical temperatures of liquation are incomplete and present sometimes considerable disparities; a method has been perfected in the present work to determine these temperatures with accuracy. MISCIBILITY GAP OF THE LEAD-COPPER SYSTEM Review of Literature. The generally admitted outline of the Pb-Cu equilibrium diagram is shown by Fig. 1. This figure, with its numerical indications, is taken from the review of Hansen and ~nderko;' compositions are given in weight percent, as will be the case in the remainder of this paper. Between 36 and 87 pct Pb, Pb-Cu alloys separate into two layers, in the liquid state. The critical temperature of liquation has been much disputed in earlier studies, where values up to 1500°C were claimed; but a reliable study of ~ohnen,' based upon differential thermal analysis, gave a value of 990°C; this rather low value was verified by a recent study of Schiirmann and Kaune? based upon thermodynamical properties of the Pb-Cu alloys, which predicted a value of 1002°C. Liquid miscibility gaps were also studied by means of chemical analyses. Satisfactory results were generally obtained with the method consisting in taking samples of the two liquid layers in equilibrium and submitting them to chemical analysis; however, this method becomes delicate near the critical temperature. With this technique, Friedrich and waehlerts ob-

Jan 1, 1968

By D. R. Mitchell

MEETING for the thirteenth time in New York as part of the five-ring circus known as the Annual Meeting A.I.M.E., the Coal Division experienced a wartime boom in attendance. Technical sessions were crowded and whereas 65 seats were set up for the annual luncheon meeting of the Division over 100 members showed up, many of whom had to be fed elsewhere. Possibly the Coal Division should adopt "13" as its lucky number. Discussions at technical sessions, formal and informal, were lively. Those papers containing material directly concerned with the war, or containing information that might be usable for war industries, were enthusiastically received. Some criticism was made in regard to the present method of handling discussions and it was suggested that better success would be had in getting discussions in the record by the use of hired reporters. This is being considered by the executive committee of the Coal Division.

Jan 1, 1943

By St. John, JOHN Ancel

AT THE New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,1 in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to bean alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papers which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangements were therefore made to present that evidence at this meeting. MATERIAL EXAMINED The material examined was high-emission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated.

Jan 1, 1927

By L. D. Jaffe, R. K. Pitler

IT would clearly be advantageous to produce molten titanium, suitable for alloying and casting, directly from the relatively inexpensive tetra-chloride, without using a metallic reducing agent. Accordingly, a preliminary investigation has been made of the production of titanium by hydrogen reduction of the tetrachloride in an electric arc furnace. For the reaction: TiCl4(g) + 2H2(g) ? Ti(s) + 4HCl(g), Lockhart and his colleagues' have calculated equilibrium constants at 800" to 1500°K, based on tables of Brewer.' Extrapolating these data on the assumption that the heat of reaction varies linearly with temperature, and using Brewer's value for the heat of fusion, there is obtained for the reaction: TiCl4(g) + 2H2(g) ? Ti(l) + 4HCl(g) an equilibrium constant at 2100°K (100" above the melting point) Kp = (PHCl)4/pTlcl4 (Ph2)2 = 0.167 atm. If this is correct, starting with hydrogen saturated with TiC14 at 25°C, where the vapor pressure of the latter3 is 12.6 mm, and maintaining the overall pressure at 1 atm, 99 1/4 pct of the TiC14 would be reduced to Ti at equilibrium. An arc furnace designed for the melting of titanium and lined with water-cooled copper was used for the preliminary experimental check. Its inside diameter was 2 7/16 in. and height 6 in. The water-cooled electrode was tipped with 3/4 in. diam tung-sten. In the one run carried out, the furnace was charged with a starting batch of 293.35 g of scrap titanium,' analyzing 99.24 pct Ti. After the system was twice pumped out and flushed with argon to remove air, the arc was struck in argon and kept at 400 amp dc, electrode negative, for 1 min to melt the starting batch. Commercial tank hydrogen, dried by passing over silica gel and bubbled through technical grade TiC14 at room temperature, was then admitted to the furnace. The inlet tube directed this gas downward toward the arc and melt; the gas outlet was at the top of the furnace. The quantity of gas passed through was not measured accurately but is estimated to be about 50 liters per min at a few mm of mercury above atmospheric pressure. The arc was held in the H2-TiC14 mixture at 400 amp with little difficulty. After 10 min the arc burned through the copper lining above the melt, admitting water and ending the run. (This had happened frequently in straight melting runs under argon, and is not thought due to the atmosphere used.) In the furnace were found an ingot, several small pieces, and a little metallic powder, evidently formed when water entered the hot furnace. Some titanium also clung to the electrode. The portions were weighed and separately analyzed for titanium. Their total weight was 321.76 g of 94.82 pct overall purity. Much of the impurity consisted of tungsten broken off when the titanium was removed from the electrode. No detailed impurity analysis was made because the starting materials were impure and flooding the furnace introduced further contamination. Thus, the metal recovered contained 305.08 g Ti, as compared to 291.12 g in the starting batch. Titanium could not have been carried over from previous melting runs in the furnace, as the interior was sandblasted and the electrode ground clean before the run. Evidently at least 13.96 g of Ti were produced from TiCl4. Since this would require complete reduction of 430 liters of TiCl, gas at 12.6 mm of Hg, the efficiency of the process must have been rather high. Experimental work is continuing. No reason is seen why the process could not be scaled up to the size of a 30-ton steel-melting arc furnace. In a large unit there would be a large molten pool from which liquid metal could be withdrawn for alloying and casting. The problems of electrodes and power supply are similar to those arising in arc furnaces for melting titanium. Unreacted TiC14 and the HC1 in the exhaust gases could be recovered; unreacted H2 could be dried and re-used. The melt would be saturated with hydrogen, whose solubility in liquid titanium is unknown. Small amounts of hydrogen seem to have little effect on the properties of titanium.5 If the amount introduced was so large as to impair properties or cause casting difficulties, it could be reduced by holding the melt under an inert gas or by pumping on it, prior to casting. Acknowledgment The authors would like to thank I. Preble and M. Goldman for their valuable aid in the experimental work and the thermodynamic calculations, respectively. References 1R. J. Lockhart, J. J. Ward, M. J. Hussey, and J. W. Clegg: In unpublished report, "U. S. Air Force Project Rand. Titanium and Titanium Base Alloys." Battelle Memorial Institute (1949) 37-44. 2 L. Brewer et al: Chemistry and Metallurgy of Miscellaneous Materials—Thermodynamics. Ed. by L. L. Quill. pp 13-39, 60-192. (1950). McGraw-Hill Book Co. 3 K. Arii: Scientific Reports. Tohoku Imp. Univ. (1933) 22, 182. 4 R. S. Dean, J. R. Long, F. S. Wartman, and E. L. Anderson: Transactions AIME (1946) 166, 369-381; Metals Technology (Feb. 1946) TP 1961E. * R. I. Jaffee and I. E. Campbell: Transactions AIME (1949) 185, 646-654; Journal of Metals (Sept. 1949) TP 26813.

Jan 1, 1951

By F. E. Jaumot, R. L. Smith

Self-diffusion in zinc has been used as an instrument for comparison of the absorption and sectioning techniques as a means of studying diffusion. Single crystal as well as poly-crystal samples were used asanda the temperature range of diffusion extended from 200° to 415°C. For temperatures above 200°C, the data indicate that the results obtained from the absorption technique agree with those obtained from the sectioning technique. The effect on the values of the diffusion coefficient of electroplating vs evaporation as a means of applying the tracer was investigated and no significant difference observed. It was found that an excess or deficiency of tracer did not materially affect the results obtained from the sectioning technique, but invariably caused errors with the absorption technique. NEARLY all self-diffusion experiments and many alloy diffusion experiments have employed radioisotopes as the instrument for following the diffusion. Of the various techniques in which radioisotopes are applicable, the two most widely used are the sectioning and absorption techniques. In the former, the diffusion coefficient is obtained from a curve of log concentration vs the square of the mean penetration depth. In the latter, the diffusion coefficient is calculated from a knowledge of the decrease in activity at the surface after diffusion. In spite of the importance of knowing the reliability of the diffusion data and the widespread use of these two techniques, they had not been directly compared experimentally on the same samples. Thus, such a comparison was worthwhile. The specific system chosen for this comparison was the self-diffusion of zinc, since the metal was readily obtainable in high purity, single crystals were easily grown, and the anisotropic features of the diffusion added an additional factor of interest to the comparison. Self-diffusion in both single and polycrystals was investigated, since the possibility existed that grain boundaries and grain boundary diffusion might produce different effects for the different techniques. Also, the effects of electroplating vs evaporation as a means of applying the radioactive tracer, and the effects of applying an excess or deficiency of tracer material were studied. The general experimental procedures and the mathematical analyses of both techniques have been described previously in some detail, and only those points essential to an understanding of the present work will be discussed here. The mathematical analysis of the sectioning data requires only a knowledge of the solution of Fick's equation. where C,, is the initial concentration, C is the concentration at depth x, D is the diffusion coefficient, and p is the absorption coefficient of the solvent metal for the radiation from the solute. Having obtained F from the experiment, the value of z can be read from a plot of F vs In z, and D can then be calculated if is known. The necessity of knowing the absorption coefficient causes most of the criticism of the absorption technique. It is very difficult to measure accurately under the conditions existing in the diffusion experiment, but it is absolutely necessary, as will be indicated briefly later. Portions of this problem have been discussed in detail elsewhere." The difficulties involved in the measurement of the absorption coefficient arise from three principle factors: the physical characteristics of the absorber, the geometry, and complex radiation spectra. The first two are heavily dependent upon the third. If

Jan 1, 1957

By M. H. Richman, E. S. Meieran

An analytical method is presented which enables the electron diffraction patterns from a twinned region to be indexed. The method has only been applied to (112) twins in bcc lattices, but can easily be adapted to other types of twinned lattices. Calculations of all twin spots, including those superimposed on matrix spots, is made possible by this method. SINCE the advent of transmission electron microscopy, the analysis of selected-area electron diffraction patterns has become very important in the interpretation of electron micrographs. Frequently, as in the case of some martensites, twinned areas are observed and give rise to complex diffraction patterns, which so far can be analyzed only for the simplest orientations of the thin foil specimen with respect to the electron beam. In order to simplify the analysis of twin patterns of more complex orientations, an analytical method was devised which is capable of predicting the positions of all reflections from both matrix and twin regions for all possible foil orientations. Although the method has only been applied to the case of bcc metals twinned about a (112) plane, it is equally applicable to other Bravais lattices. This method has been successfully applied to selected-area electron diffraction patterns of Fe-Ni and Fe-Ni-C martensites and drawn tungsten wire. PROCEDURE Imagine the reciprocal lattice corresponding to a bcc material, with each point hkl representing the crystallographic plane (hkl). Since the extinction conditions require that for this lattice, only reflections where h + k + 1 = even integer are allowed, the three dimensional reciprocal lattice is actually fcc. Since in real space twinned regions and matrix regions are mirrored across a (112) plane, the twinned reciprocal lattice is derived from the matrix reciprocal lattice by a rotation of 180 deg about a (112) direction. While it is possible to calculate how a point hkl will shift under a twinning transformation to a new point htktlt using only the reciprocal lattice based on the orthonormal vectors [100], [010], and [001], the calculations are greatly simplified if a new orthonormal coordinate system containing the twin axis is introduced. The twinning operation then becomes a simple rotation of 180 deg about a principal coordinate axis (in this case the twinning axis), and a retransformation back to the original reciprocal space will give the position htktIt of the twinned reflection.

Jan 1, 1963

By Nicholas J. Grant, William H. Ferguson, Bill C. Giessen

Ta-lr alloys have been examined over the complete range of compositions using metallographic and X-ray techniques. The terminal solid-solubility limits, solidus temperatures, and intermediate phases were determined. There are four inter-mediate phases: o, tetragonal, analogous to a (Fe-Cr); 0,. orthorhombic; az, tetragonal; and a TaZr,, cubic, AuCu, structure. Of these, o and a, melt peritecticaLly, a, decomposes peritectoidally, and a TaIrs has a congruent melting point. Three peri-tectic and one eutectic reactions occur. 1 HE Ta-Ir phase diagram has not been treated in the literature. Intermetallic phases and terminal solid solubilities have been described and estimated.'-4 The previous findings have been confirmed in this work. A complete diagram with additional phases and solidus curves is presented. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by the National Research Corp., Cambridge, Mass., and iridium powder of 99.9 pct purity, supplied by the Bishop Co., Malvern, Pa. Both powders were -200 mesh. Table I lists the analyses as given by the suppliers. A standard procedure was employed in making the alloy buttons, which was described in detail in Refs. 5 and 6, and which included repeated arc-melting of powder compacts and determination of the composition by the weight-balance method. This is especially justifiable due to the similar vapor pressures of tantalum and iridium. In the critical parts of the diagram, a spacing of 1/2 at. pct was used, based on premelted master alloy material. The observed structures and X-ray spectra were consistent with the composition sequence of the alloys. Table II lists the final alloy atomic percentages with the calculated percent error of composition. Cross sections representative in grain size and composition were selected for the study, as described in Ref. 5. Based on prior experience, no contamination from the tungsten electrode was considered. Temperature measurements were obtained using a Leeds and Northrup optical pyrometer and have been described extensively in Refs. 5 and 6. All heat treatments were made in the high-vacuum tantalum tube furnace mentioned in Ref. 5. Samples annealed in tantalum containers cooled from 1800" to 1000"~ in 5 sec; those annealed in ceramic crucibles cooled over the same range in 15 to 30 sec. The thermal treatments are listed in Table 111. All specimens were homogenized at 1735°C for 24 hr. Tantalum-rich compositions were treated in tantalum buckets. Iridium-rich compositions were annealed in tantalum buckets below the eutectic temperature of 1950°C; up to 2200°C, tungsten-lined tantalum baskets were used; and above 2200°C thoria crucibles were used. It was found that refractory oxides (in early stages of the investigation alumina crucibles were used up to 1800°C and thoria crucibles were used to 2400"~) give off minute amounts of oxygen and thereby influence the microstructure considerably, or react directly with the alloys.

Jan 1, 1963

By J. S. Kirkaldy, D. G. Fedak

The extra degree of freedonz introduced by a second independetzt concentration in a tenzary system gives rise to the possibility of unstable planar phase interfaces in semi-infinite diffision layer couples. Diffusion paths which pass continuously in and out of too-phase regions of the phase diagram but which are not coincident with tie-lines give rise to super saturated zones which may be either adjacent to or isolated from planar phase interfaces, with corresponding nonisolated or isolated precipitates. Nonisolated precipitates are equivalent to morphological development of the interface. Selected couples in the ternary systems Fe-Ni-Cr and Cu-Zn-Sn have been examined nzetallographically and ifz the latter case both isolated and uo~zisolated precipitates have been observed. The diffusion path in one of the couples showing interface morphological developtnent has been examitled using electron probe microanalysis. IGNORING the spurious effects of preferential grain boundary diffusion and anisotropic crystal growth7 it can be unequivocally stated that it is impossible for a binary isothermal diffusion couple constructed of two unsaturated phases to sustain a nonplanar phase interface. Consider for demonstrative purposes the schematic phase diagram of Fig. l(a). Given an initial flat phase interface, semi-infinite boundary conditions and the internal boundary condition fixed by the constitution diagram, xB = xB(T), the unique solution of the diffusion equation requires a persistent flat interface. No other solution is possible. If, however, we anticipate the involvement of surface tension, then the internal boundary condition must be written xB = xB (T,Y) where r is the radius of curvature of a hypothetical nonplanar interface. The introduction of a new parameter such as r can be equivalent to the release of an internal constraint, so that a stable nonplanar interface may be possible after all. Consider a perturbation to the interface as indicated in Fig. 1(b). According to the Ostwald-Freundlich equation: which is applicable to a system of this constitution, the solubility of A in the matrix ß ,xB (Y), at a point of curvature r is given by where Va is the molar volume of the a-phase, R is the gas constant, and a is the interfacial tension. Since the right hand side is positive, xB(r) >xB cm, as indicated in Figs. 1(a) and 1(c). Accordingly, the perturbation will carry the interface concentration in a direction which is opposite to that which would sustain local equilibrium. Such a perturbation is necessarily moderated and the system is returned to its initial condition. This result is general for all binary couples since we can regard an interfacial perturbation as an attempt to precipitate within un-

Jan 1, 1962

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

By Robert F. Mehi

The mechanical behavior of metals and alloys is presumably conditioned by two factors; namely, the crystallinc symmetry and the interatomic forces. Considerable attention has been given to the first of these factors through the recent advances in X-ray technique. It is the purpose of the present paper to call attention to the importance of the second of these factors, to point out promising methods of investigation, and to present some pertinent data. Plastic deformation takes place by slip along atomic planes.' This slip may be inhibited in a number of ways: by the interatomic forces of, cohesion which bind the atoms rigidly in a lattice structure, which in pure metals is usually of high symmetry; by latticc distortion caused by solid solution formation or by mechanical strain; by the intercrystalline boundaries whcrc slip is restrained, probably by the non-registration of the atom planes in adjacent crystal1ites;2 and by the presence of small hard particles which serve to "key" the slip along the atom planes.5 In pure metals, and perhaps also in solid solutions, the atom planes of easiest slip are those exhibhing the greatest density of atomic population and the greatest interplanar distance4 and apparently can now be pre-dict,ed from the analysis of the lattices. Concerning the interatomic forccs, which resist this slip by holding the atoms firmly together, little is known. Most textbooks on physical metallurgy, following the work of Bot-tone,5 correlate the hardness of the pure metals with the atomic volume,

By A. B. Kinzel

ALTHOUGH the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approxi-mately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cementite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consider-ation of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:1 C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown in Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850° C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the

Jan 1, 1934

By Arthur F. Taggart

Some years ago, A. M. Gaudin and one of the authors published a paper showing removal of tar acids from solution by sulfides preferentially as compared to gangues (specifically by galena as compared to quartz).' The underlying phenomenon was classed as adsorption, and the paper went on to develop the general thesis that so far as water-soluble frothing and collecting agents in flotation are concerned, the phenomenon of adsorption is one of controlling importance. Adsorption was defined in that paper as "a process of rearrangement of a system, which results in establishing a difference in concentration, as between the interfacial layers and the bulk of the phases, of a substance or substances initially uniformly dispersed in one or several of the phases." The paper went on to develop the relation between adsorption and surface cnergy according to Gibbs' equation (which may be thrown into the form U/c = KdT/dc, where U = excess concentration in surface layer, c = concentration, T = surface tension, and K is a constant), and pointed out that, according to this equation, degree of adsorption and change in surface tension vary directly. The present paper offers a somewhat different definition for the term adsorption; and sets up, in sweeping terms, the generalization that simple chemical reaction underlies the functioning of the flotation reagents which control mineral collection, when these reagents are soluble in and act from solution in the water of the pulp. Adsorption According to the modified definition, adsorption means concentration at an interface between different phases in a heterogeneous system (thus far the definition runs as before), by the action of some mechanism, of which nothing is properly implied in the word, and concerning which the user of the word is probably in entire ignorance. Thus defined,

Jan 1, 1930

By H. E. Montgomery

Engineering trends for some years have been toward higher temperatures, both in process work and in steam generation. Progress in design has been dependent upon the development and evaluation of suitable alloys. Elementary knowledge of the limitations of copper-base alloys indicate their unsuitability for the higher ranges of operating temperatures; say, for steam to 950°F. Emphasis upon the more severe conditions perhaps is a reason why more complete evaluations have not been made for copper-base alloys over their range of suitability. However, the few studies made show clearly the need for more accurate evaluations. Some copper-base alloys long looked upon favorably because of superior room-temperature properties are not as desirable as some others perhaps not so "strong" and "hard," as measured by usual acceptance tests. Load-carrying capacity and structural stability arc two important factors. Structural stability as influenced by temperature, by presence of corrosive media, or by the effects of stress itself, frequently is a limiting factor. An early reference to creep properties of the cast copper-base alloys is that of Brown1 (Admiralty gun metal, Cu 87.5, Sn 10.1, Zn 2.3 and Pb 0.08). His tests were similar to present-day stress-rupture tests without measurement of creep elongrttion. Loading was in steps with usually 24 hr. between steps, and continued until failure. He advocated a "useful strength value" of 61/2 tons (I4,560 Ib.) per sq. in. at 572°F. (300°C.). A specimen broken in 1/2 hr. at 572°F. had a strength of 21 tons (26,880 Ib.) per sq. in. The strength values as determined by 1/2-hr. tests and those by the longer stress-rupturc start to differentiate at 392°F. (200°C). This is the temperature at which time at load began to play an important part. Bolton, Price and Hebemann2 give creep curves on 88-10-2 (A.S.T.M. B-60, CU 88, Sn 10, Zn 2) and steam or valve bronze (A.S.T.M. B-6I, Cu 87.50, Sn 6.00, Zn 3.75, Pb 1.70) at 500°F. Direct comparison of the two alloys under 7500 lb. per sq. in. stress showed the steam bronze (A.S.T.M. B-61) superior in creep strength to the 88-10-2 (A.S.T.M. B-60). The steam bronze shows no creep after 700 hr. (1540-hr. test). The 88-10-2 shows a rate of about 7.0 per cent in 100,000 hr. over the last 700 hr. of the test. Creep curves on the steam bronze are also given at the same temperature (500°F.) with loads of 6500 lb. per sq. in. and 8000 lb. per sq. in. These indicate "creep strengths" (creep rate within I per cent in 100,000 hr.) in excess of 8000 lb. per sq, in. for this alloy. It was found that higher percentages of tin are detrimental to creep resistance. This is caused by the presence of or formation during test of considerable alpha-delta eutectoid in the higher tin alloys. Bolton also states that the high

Jan 1, 1945

By Arthur F. TQggQrt

THE approximate status of education in ore dressing in 1871 is reflected by Rossiter W. Raymond in an article written at that time presenting the curricula and descriptions of the laboratories at the various mining schools in the United States. For the most part, the curricula in which ore dressing was taught were for mining engineering. They comprised courses in geology, mining, and pyrometallurgy about equal in point or credit weights; a short course in ore dressing, and a somewhat longer course in assaying; and courses in surveying, hydraulics, power, and strength of materials-all superimposed on a broad foundation of physics, chemistry, and mathematics. Some curricula contained a fair content of the humanities. Then, as now, the emphasis on fundamentals was greater in the older colleges and universities. The report on the Columbia School of Mines, then relatively young, emphasized that a large percentage of its students were college graduates. As technical and scientific knowledge grew, first metallurgy and then geology were set up as separate curricula. So far as curriculum designation is con-

Jan 1, 1947

By W. B. Coleman

Considerable discussion on the effect of iron and steel scrap in blastfurnace burdens was presented in the January, 1927, issue of Mining and Metallurgy. Therein the question is asked as to what causes the difference in physical properties of pig irons where the chemical analyses are practically the same. This point no doubt has been noticed by a number of furnace operators, but several years ago very little thought was given to it. The foundries purchased pig iron, had it analyzed and found it to be within their specification. The castings made from this iron at times would be satisfactory and at other times hardness and shrinkage would occur. Since the iron was chemically correct the foundries generally were at a loss as to what to do. They changed their method of melting in the cupola and in some cases this corrected the trouble. In some instances the foundry would continue eliminating a brand of iron until the castings produced were satisfactory. Through this process of elimination they would finally arrive at the conclusion that a certain brand of iron was causing the trouble. During the course of this elimination minor changes might have been made in the melting and in the end satisfactory castings were secured without discovering any definite reason for the trouble. Frequently the foundries blamed the manufacturer of the pig iron although the seat of the trouble was in their own method of melting. I have in mind one foundry in particular that was using three brands of pig iron for producing their castings and their losses were rather high. Three entirely new brands of iron were substituted in the charge and still the losses continued. Even after using six brands of pig iron the management felt that the pig iron was the cause. The difficulties encountered in the melting of iron in the cupola, over the past several years, reflect in a great many cases on the operation of the cupola. At different times certain brands of iron were unsuitable for producing a certain class of castings, but at the same time one could see no reason why the iron should be considered abnormal. Irons from furnaces where production and low cost are the main factors that are being used in foundries produce in most cases harder cast-

Jan 1, 1927

By M. S. Burton, G. V. Smith, A. Rosen

The kinetics of re crystallization and the effect of recovery on recrystallization of pure iron were investigated within the temperature range of 517" to 632 OC. Grain growth and activation energies were also studied. Two stages can be distinguished during recrystallization; the first is gvowth-controlled and the second is nucleation-controlled. The extent to which the first stage succeeds before the second stage begins depends on both temperature of recrystallization and temperature of recovery. The softening of cold-worked metals and alloys due to transformation of the deformed crystals to strain-free equiaxed grains during annealing is well-known, and early inestiators established that recrystallization kinetics is strongly influenced by minute quantities of impurities. Generally, it is believed that impurities decrease the rate of recrystallization and the rate of grain growth. To understand the basic phenomena of recrystallization, investigations should be on pure materials. Most of the research on high-purity materials has been on metals having the fee Bcc materials, and especially high-purity iron, have been studied only in recent years. It is known that recovery may influence recrystalliation;" however, no general description of the influence, applicable to all materials, has been presented. This paper presents results of a study of the recrystallization kinetics of high-purity iron, after 60 pct cold deformation by drawing, with particular reference to the influence of recovery on the rates of recrystallization and grain growth. From observations of these rates, conclusions are drawn concerning nucleation. MATERIAL AND EXPERIMENTAL PROCEDURE Preparation of Material. High-purity iron, prepared by zone refining of vacuum-melted electroiytic iron at Battelle Memorial Institute under sponsorship of the American Iron and Steel Institute, was used in this study. Table I gives the reported chemical analysis of the material, taken at a point near the last molten zone and thereby rep- resenting the maximum impurity level for the entire bar. Prismatic specimens, approximately 10 x 10 X 50 mm, were sawed from the 50-mm-diam bar, perpendicular to the zone-refining direction, and turned to cylindrical shape. These specimens were sealed in quartz capsules under vacuum, approximately 10"e mm Hg, austenitized at 930° C for 15 min, slowly cooled, removed from the capsules, and cold-worked in air by swaging to approximately 20-pct reduction of area. The encapsulating, austenitizing, and swaging operations were repeated two additional times, after which the samples were encapsulated, austenitized, and cold-drawn to 60-pct reduction of area. A further vacuum anneal at 630°C for 120 min and cold drawing to 60-pct reduction of area produced wire 2.8 mm in diameter. The drawn wire was electropolished to remove deformed material on the surface, after which it was sawed into 4-mm-long specimens for the recrystallization study. Microscopical examination before the final cold reduction revealed equiaxed grain structure with very fine grains in a thin layer near the surfaces of the specimen and nearly uniform ASTM 3-4 grain size in the center. Recrystallization Heat Treatment. a) Direct Recrystallization of Cold-Worked The 60 pct cold drawn iron specimens were recrystallized at five temperatures, 517, 556, 590°, 612, and 632C, in a lead bath covered with graphite (the temperature was controlled to 1°C). Specimens were treated for twelve different times at each temperature, and all were water-quenched after heat &eatment. b) Recrystallization Following Preliminary Recovery Heat Treatment. After cold working, specimens were sealed into quartz capsules under vacuum, 105 mm Hg, and recovery-annealed at 362", 400", and 440°C for 20 hr prior to recrystallization. No evidence of recrystallization was found

Jan 1, 1964

By A. L. Galpin

INTRODUCTION For many tailings ponds, particularly those having substantial watershed areas, the control of pond water levels will be a major factor influencing the operation of the pond and the design and construction of the dam retaining the pond. This paper summarizes the basic factors affecting the control of water in tailings ponds, methods of water control, and methods of estimating the variables involved. The influences that pond water levels can have on the design, construction, and stability of tailings dams are explained in order to emphasize the importance of water control in the overall planning of mine tailings disposal systems. Two examples of pond water control planning conclude the paper. BASIC FACTORS The principal factors influencing the control of water in tailings ponds are illustrated on Fig. 1. Fig. 1 (a) shows the general disposition of the tailings solids and water in the pond; the solids settle from the slurry to form "slimes", deposits sloping down into the pond from the points of discharge; these slimes hold volumes of water in the voids between solid particles; water in excess of this "retained" water forms a pool of "free" water laying over the slimes deposits. In some cases, tailings solids (and water) go to the tailings dam for its construction. Fig. 1 (b) indicates those ways additional to tailings disposal in which the pond gains or loses water. These include surface and sub-surface runoff from the pond watershed, water reclaimed from the pond for ore processing, evaporation, and seepage. Seepage losses sometimes include water draining from tailings sand placed in the dam, but a portion of the total seepage flow is often collected and returned to the pond in order to avoid downstream pollution and to recover water for re-use. PRINCIPAL REQUIREMENTS In relation to the control of water in a tailings pond, the first requirement is usually to maintain a pool sufficiently large to ensure adequate clarification of the free water prior to its reclaim for use in the mill, or its discharge from the pond.

Jan 1, 1972