Search Documents

By R. J. Reynik, F. R. Meeks

IN the classical paper1 of Mehl and Rhines entitled "The Rates of Diffusion in the Alpha Solid Solutions of Copper", the authors state: "It has been mathematically demonstrated that the treatment of the data as though the diffusion were taking place between two flat plates instead of radially in a cylinder has no appreciable effect upon the results. Were the bars of a much smaller diameter, a modification of the analytical treatment would have been required." Unfortunately, the errors in the reported concentrations are much too large to neglect, as shown in the results below. A planar treatment of diffusion data assumes that the reference planes separated by a nominal distance (AX) have identical areas. An adjustment must be made on the concentration data should the successive diffusion planes differ in area. The Mehl-Rhines' diffusion samples were cylindrical with copper electroplated onto copper-based alloys. Successive surface areas through which diffusion occurs are in the ratio ri/r1, where ri is the radial distance between the center of the sample and the center of the i th shell to which the host (alloy) atoms diffuse, and r1 is the radial distance between the center of the sample and the center of the innermost (i = 1) experimentally reported shell from which the alloy atoms diffuse. Hence, ri/r1 (i = 1, ..., n layers) is a dimensionless correction factor to be multiplied by the reported concentration data before planar-data analysis is attempted. In the forty-seven samples reported, the original interface between the copper alloys and the electroplated copper was located at a mean distance of 8.255 mm from the center of the samples. The successive layers, machined off the samples, were approximately 0.0762 mm thick. The distance (xi) at which concentration (ci) was reported was always a distance measured with respect to the original interface, that is, with respect to the fixed distance of 8.255 mm. Hence, the as yet undiscovered Kirkendall Effect was precompensated. The values of ri and r1 are therefore given by ri = 8.255 + xi and Y, = 8.255 + x,. The illustrative table below lists the position xi (mm), ri (mm), the value of ri/r1, the reported concentration (ci) in weight percent (only valid for radial analysis of data), and the corrected concentration [c'i = (ri/r1)ci] in weight percent (only valid for planar analysis of data). Similar tables can be constructed for the remaining forty-six samples. The corrected data can be used to re-evaluate the diffusion coefficients for the reported systems.

Jan 1, 1965

By G. Pomey

Heat-resisting chromium steels and alloys treated at 825° or 9.50°C (1527° or 1742°F) in a carburizing atmosphere exhibit an extensive carbide precipitation. This carbide precipitation may be succeeded by the FeCr a phase or by a carbide with a higher carbon content. Point analyses carried out with an electron mi-croanalyzer make it possible to study the depletion of chromium in the matrix after precipitation has occurred and to determine the chemical composition of carbides. In particular the content in the carbides of Fe, Ni, and W, elements which substitute Cr, can be accurately determined. HEAT-resisting chromium steels and alloys employed in the construction of gas carburizing and carbonitriding furnaces are subjected to a succession of oxidizing atmospheres during heating and cooling and to carburizing atmosphere during isothermal stage. Such a sequence of thermal cycling causes embrittlement and corrosion in the furnace materials. A quantitative study of the structural changes induced in the furnace materials has not received much attention in the past. However, utilization of the electron probe microanalyzer and other modern techniques has permitted a point analysis of the various phases formed and to follow their relative evolution. This paper gives results as regards the nature and composition of the carbide precipitation and the distribution of chromium in the matrix during only the carburizing periods. The structural changes subsequently produced during oxidizing periods will be presented eventually. METHODS AND MATERIALS Metallographic, X-ray diffraction and Castaing electron-probe microanalysis1 techniques have been employed to study carbide precipitation and evolution and the changes in the composition of the matrix in heat-resisting steels and alloys.

Jan 1, 1961

By J. C. Williams, M. J. Blackburn

MANY aspects of the formation of the metastable w phase in titanium-transition metal alloys have been described in several recent papers.1-4 These papers have reviewed earlier work on the w phase and have further defined most of the important features related to the formation of this phase, e.g-., its crystal structure, composition, and morphology. There are, however, several important points regarding formation of the w phase in titanium alloys which have been described in less detail. Two of these are the relationship between lattice misfit and w phase morphology and the influence of lattice misfit on the mode of formation of the equilibrium a phase. In this communi- cation we will present transmission electron microscopy results relevant to these two points. The alloys used in this study were prepared by non-consumable electrode arc melting, each 30-g button being remelted a minimum of twelve times. The alloy compositions we have studied are listed in Table I. Thin foils were prepared using standard techniques described elsewhere. Two distinct c' phase morphologies have been reported in earlier papers. The phase is ellipsoidal in the Ti-Mo3 and Ti-Nbl system and cubical in the Ti-V3 system. Results of the present study show that the w phase is also cubical in Ti-Mn, Ti-Fe, and Ti-Cr alloys as illustrated in Fig. l(b) to (d). Fig. l(a) shows the ellipsoidal morphology in Ti-MO3 for comparison purposes. It was suggested in an earlier paper3 that the w phase morphology may be controlled by the lat-

Jan 1, 1970

By Harry A. Roe

The power drag scrapers and the slackline cableway excavator have been called "long-range excavators." Broadly, their field of usefulness is restricted to work in which their long range of action permits them to operate economically, and which other, possibly more conventional, excavating units cannot do. Both of these machines dig or lift material and transport it to a remote dumping point. They combine these two functions in a single machine, nearly always in a single straight-line motion. The purpose of this paper is to examine the important features that distinguish the machines in this group from each other, as well as from other groups. The Machines The "power drag scraper" is a long-range excavating machine that employs a bottomless drag scraper operated back and forth between digging and dumping points by two haulage cables. The typical arrangement is that of Fig. 1. This is the "slusher" of the underground mine, as well as the "dragline scraper" of the sand and gravel industry, and other open-pit mining operations.

Jan 1, 1938

By Harry A. Roe

The power drag scrapers and the slackline cableway excavator have been called "long-range excavators." Broadly, their field of usefulness is restricted to work in which their long range of action permits them to operate economically, and which other, possibly more conventional, excavating units cannot do. Both of these machines dig or lift material and transport it to a remote dumping point. They combine these two functions in a single machine, nearly always in a single straight-line motion. The purpose of this paper is to examine the important features that distinguish the machines in this group from each other, as well as from other groups. The Machines The "power drag scraper" is a long-range excavating machine that employs a bottomless drag scraper operated back and forth between digging and dumping points by two haulage cables. The typical arrangement is that of Fig. 1. This is the "slusher" of the underground mine, as well as the "dragline scraper" of the sand and gravel industry, and other open-pit mining operations.

Jan 1, 1938

Discussion of the paper of M. B. YUNG, presented at the Pittsburgh meeting; October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2451 to 2458. T. T. READ, New York, N. Y.-I might .point out that this paper of Mr. Yung's is on a field that is comparatively little known. It is not as well known as the Kochiu tin field, of Yunnan, which is probably the third . in tin output of the world. This field under discussion is considerably further west and the tin which is produced here is, according to Mr. Yung, of somewhat higher grade than the Yunnan tin, and is used by the refiners at Hong Kong to improve the grade of the Yunnan tin. Most of you know that the tin from the Yunnan is shipped to Hong Kong, where it is refined and shipped to Europe. Mr. Yung points out that the Fu Chuan deposits are entirely alluvial and not found in any veins. They .differ in that from the Kochiu deposits, which Leclere says are "nullement alluvionels; leur origéne filonienne est de plus evidentes." Granite is the country rock here; doubtless the tin occurred in veins in the granite, and the deposits have resulted from the disintegration of the granite. This is a country of strong erosive agencies. The country is semi-tropical, and the rainfall is heavy, so that one would naturally expect deep surface erosion of this kind.

Jan 4, 1915

By J. H. Bechtold

Tensile properties of annealed molybdenum were investigated from 1000" to—200°C. In the vicinity of room temperature a well-defined transition in tensile properties occurs. Reduction in area decreases from over 80 pct to 0 pct and, simultaneously, the yield strength increases about 60,000 psi. MOLYBDENUM, tungsten, iron, and many other metals and alloys with the body-centered cubic and hexagonal close-packed crystal structures change from ductile to brittle behavior over some relatively narrow temperature range. The temperature at which this transition in ductility occurs depends on chemical composition, microstructure, and method of testing. When fine grained, completely recrystallized molybdenum of commercial purity is tested in uniaxial tension at a slow strain rate, the transition occurs at slightly below room temperature.' Iron2 and tungsten3 tested under similar conditions become brittle at temperatures close to the boiling point of nitrogen, — 195°C and at about 200°C, respectively. A sharp change in ductility is uncommon in metals with the face-centered cubic crystal structure, however, a relatively sharp transi- tion in notched bar impact properties has been observed below room temperature in a face-centered cubic copper-antimony alloy.4 A transition from ductile to brittle behavior is usually explained by the concepts originally developed by Ludwik,5 and discussed and elaborated on by others including Orowan,6 Hollomon and Jaffe,7 and Gensamer8 In brief, there are two aspects to strength, first the resistance to flow and second the resistance to fracture. Both are functions of temperature, strain, strain rate, stress system, composition, and microstructure. With decreased test temperature the flow stress required to initiate plastic deformation increases more rapidly than the fracture strength and brittle fracture occurs at that temperature where the yield strength equals or exceeds a brittle fracture strength. This investigation was conducted to determine the effects of temperature, strain, and rate of straining on the flow and fracture strengths of molybdenum above, through, and below the ductile-to-brittle transition. Other variables were held constant during testing. This information is believed to show

Jan 1, 1954

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By Salinger, Herbert

WITH the large amount of metallurgical re- search work now being done and the constant effort of the engineer to effect economies of operation, I think it is a safe prediction that the next few years will see a great change in the handling of mine products. The well-managed mine, with sufficient ore reserves to warrant the necessary plants, will increasingly call upon the metallurgist and chemist for the solution of its problems. Shipping sorted ore or concentrate to the nearest smelter will not be the course followed. From ore to metal, or at least to a product directly salable to the consumer, will be the practice followed. As a consequence, mine managers will be increasingly interested in metal trade problems. By metal trade I mean the buying, selling, shipping, handling, and all the practices, forms and customs that go to make up the trade.

Jan 1, 1928

By J. P. Zannaras

If we assume that testing of the model started at time C, that time t2 was the instant at which the elastic limit of the material was passed at the points of the maximum stress, and that at time t3 the failure of the model was completed as shown in the typical photograph (Fig. 1), then actually the photograph shows the final results of what took place between time t2 and t3. By the principle of similitude all conclusions drawn from the behavior of the model were applicable and valid for actual mine roofs up to the time t, after time t, motions and friction came into play during the destruction of the model. The events between t2 and t3 and the photograph itself are not representative of the events expected in an actual mine roof unless corrections imposed by the principle of similitude are made.

Dec 1, 1956

By Pei-Yung Huang, C. R. Hayward

In order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. Choice of Slag Composition The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, avcrage :2,3 45 to 47 pct FeO; 38 to 42 pct SiO2; 5 to 6 pct CaO; 5 to 6 pct A12O3. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-SiO2-Al2O3, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the composition near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093º ± 3ºC) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the fulfil- slag is decidedly too basic. Composition K has a slightly higher melting point (1150O + 3OC) and a higher silica content, but this is preferred because the slag is saturated with respect to tri-dymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The filial slag composition, therefore, was chosen to

Jan 1, 1949

By A. U. Seybolt

RECENTLY, cases of coexisting ordered and disordered phase equilibria have been reported among face-centered cubic metals,1"3 but not on body-centered cubic systems.4 McQueen and Kuczynski5 showed a single line as the boundary between ordered solid solution of Fe3Al type and corresponding disordered solution in the Fe-A1 phase diagram based mainly on dilatometric and magnetic measurements. Such a single line would indicate a second or higher order transition. or an absence of coexisting order and disorder. The writer found previously a two-phase equilibrium region at 800°C consisting of ordered and disordered solid solutions of Fe3Si in a matrix of approximately 1-6 wt pct Si (Fe3Si is of 14.3 wt pct Si). A similar two-phase region of ordered and disordered Fe3Al solid solutions might be expected if the similarity between Fe3Si and Fe3Si structures hold true. In the present investigation, a wire of 22 at. pct Al, balance Fe and 0.0513 cm in diameter was subjected to electrical resistivity measurement in vacuum as a function of temperature between 300 and 800°C, see Fig. 1. There was excellent agreement between data taken on heating and on cooling: no hysteresis was observed. The Curie temperature was determined to be 640 °C which agrees with the finding by McQueen and Kuczynski.5 But in addition, there were two transitional points in the resistance-temperature plot at 510oC and 400 "C. The former is thought to be a connection with the transition from disordered state to a coexisting order and disordered equilibrium state; while the latter, from such coexisting state to ordered state. Fig. 2 shows a phase diagram where the suggested two-phase region lies between dotted lines. The solid lines are those of McQueen and Kuczynski.5 Since these authors found only a single-phase boundary between ordered and disordered Fe3 Al, it would seem likely that the dilatometric method used by these authors was not sufficiently sensitive to resolve the ordering reaction into the two-phase boundaries. In addition, their phase diagram conflicts with the statement they make on P. 1 of their paper: "The sharpness of the peaks indicates that ordering to Fe3A1 is a first order reaction." The suggestion of coexisting order plus disorder in Fe3A1 must be considered tentative until confirmed by high-temperature X-ray examination. If

Jan 1, 1961

By J. L. Ratliff, R. I. Jaffee, H. R. Ogden, D. J. Maykuth

An experimental program was carried out to improve the low-temperature ductjlity of tungsten through the combined use of dispersed oxides for grain-size control and Groups VII and VIII metal additions for matrix softening. Separate binary -alloy studies showed that increasing amounts of finely dispersed thoria or zirconia and critical amounts of rhenium, osmium, and iridium were effective in significantly reducing the ductile-to -brittle bend transition temperature of tungsten as well as in increasing its re crystallization temper - LIKE most of the high-melting point bcc metals, tungsten undergoes a marked transition from ductile to brittle behavior with decreasing temperatures. The material factors which influence the transition temperature include grain size, metal purity, and the presence of dispersed phases. ature and decreasing its recrystallized grain size. The beneficial effects shown by each of these additions on transition temperature and grain size in binary combinations appeared to be additive in tevnary combinations. Thus, combined additions of 2 to 8 vol pct thoria with 5 pct Re, 0.87 pct Os, or 0.30 pct Ir were effective in lowering the transition temperature of tungsten pom 2000 to 75"C, increasing its re crystallization temperature from 1600 to 1800°C, and decreasing its recrystallized gain size from 1175 to 6800 grains per sq mm. The mechanism by which these factors are operable in tungsten is not yet clearly understood. Nevertheless, it has become increasingly apparent that the interrelationship of grain size and matrix composition governs to a large extent the degree of low-temperature ductility which can be achieved. Though it is not possible to accurately assess the relative importance of these variables, the available evidence suggests that, at low temperatures, grain-size effects predominate over purity effects. This was indicated in recent studies by Allen, Maykuth, and Jaffee,' involving single crystals containing 20 to 40 ppm 0 and 1 to 30 ppm C. Thus, while each

Jan 1, 1964

By Irving Fatt, R. M. Weinbrandt

Efforts have been made for many years to observe pore structure of sedimentary rocks on a microscopic scale. A better description of the pore structure in reservoir rock would aid in the development of relations between flow through tube network models and flow in consolidated reservoir rock. The unique qualities of the scanning electron miscroscope (SEM) make it the ideal tool to use in a study of pore structure. Previous methods of studying pore structure included plastic casts of pore space and optical microscopy.l-7 There is now available a new method to observe three-dimensional flow channels in reservoir rock: a scanning electron microscope having variable magnification from X20 to X20,000 and approximately 1000 times the depth of focus of the conventional light microscopes. This microscope also can obtain stereoscopic images and can measure and diagram flow channels so that it is possible to construct a network of tubes that will model consolidated reservoir rock. THEORY OF THE SCANNING ELECTRON MICROSCOPE The scanning electron microscope (SEM) functions by projecting a beam of electrons through magnetic focusing lenses at a specimen and recording secondary electrons excited by the primary beam. The amount of secondary electron emission portrays the topography of the specimen because more secondary electrons are emitted from high points than from low points. A schematic of the SEM is shown in Fig. 1. The property of the SEM that is of most importance in this study is its great depth of focus. The depth of focus results from using electrons

Jan 1, 1970

By R. R. Vandervoort, W. L. Barmore

Tensile creep experiments were conducted on high-purity, poly cvystalline rhenium from 1500" to 2300°C at stresses from 1500 to I0,OOO psi in a vacuum of 10-a torr. The apparent activation energy for creep was 60 kcal per mole, and the steady-state creep rate varied directly with stress to the 3.4 power. Dislocation substructure that developed during creep was studied by transmission electron microscopy. Possible rate-controlling deformation mechanisms are discussed. The creep behavior of most metals at elevated temperature can be represented by the following equation:&apos;&apos;&apos; t = Cf(s)(^)(s/E)nD [1] where i = steady-state creep rate, C = constant, f(s) = a function involving microstructure, s = applied stress, E = the average elastic modulus at test temperature, n = constant, D = diffusion coefficient According to this well-established relationship, metals with higher elastic moduli and lower diffusion coefficients should have greater creep resistance at the same stress and temperature and equivalent mi-crostructures. While no diffusion data are available, the diffusivity of rhenium should be less than that for most other refractory metals because of its high melting point and hcp crystal structure. The Sherby-Simnad relation for calculating atomic mobility in metallic systems3 predicts that the diffusion coefficient for rhenium is less than that experimentally determined for tungsten4 in the temperature region 1500. to 2200°C. At these temperatures the elastic modulus for tungsten5 is only slightly larger than the extrapolated modulus for rhenium.6 Thus, rhenium is a good possibility for a a high-temperature structural material, but few data on the creep of rhenium have been reported. This investigation was undertaken to study the high-tempera-ture deformation behavior of rhenium in detail. EXPERIMENTAL TECHNIQUES The material used in this study was consolidated from high-purity powder. After cold pressing the powder to a plate a in. thick, the billet was sintered in hydrogen at 2250°C for 24 hr. The plate was reduced to 0.100 in. by cold cross rolling with intermediate anneals at 1650°C for 20 min between passes. The plate was further reduced to 0.060 in. by unidirectional cold rolling with similar heat treatments between passes, and then finally stress-relieved in hydrogen at 1650°C for 30 min. Specimens tested at 1900°C and below were pretest-annealed at 1900°C for 2 50 hr. Specimens tested above 1900°C were pretest-annealed at 2400°C for 5 hr. The impurity content in the "as-received" plate was quite low, table I. Essentially no change in impurity levels was detected in specimens after creep testing. All creep tests and annealing treatments were conducted in a vacuum of 10-8 torr in a test furnace heated by a tungsten mesh element. The load was applied to the specimens through a bellows, and stresses were maintained to ±1 pct of the selected value by periodic corrections for changes in specimen cross-sectional area during creep and for changes in the bellows spring force due to load column extension. One-inch-diameter tungsten force rods were used in the hot zone of the furnace. Deformation at temperature was measured by optically tracking gage marks on the specimen. Temperature was measured by a calibrated optical pyrometer and was determined to ±5"C. Grain sizes were determined by the linear intercept method and specimens were examined in the "as-polished" condition, using polarized light. Specimens annealed at 1900°C had a grain size of 52 ± 5µ , and those annealed at 2400°C had a grain size of 148 * 11 µ. Pieces were cut from the gage section of creep-tested specimens and planed to a thickness of about 0.010 in. by spark discharge machining. Thin foils for viewing by transmission electron microscopy were obtained by electropolishing in a solution of 6:3:1 ethyl alcohol, perchloric acid, and butoxy ethanol, respectively, using the window technique. Bath temperature was —4OoC, and the cell potential was 35 v. The foils were examined in Siemens Elmiskop I, operating at 100 kv. RESULTS AND DISCUSSION In order to analyze the results from creep experiments, Eq. [I] is rewritten in the following form: <=Kf(s)ne-/RT [2] where K = constant, ?// = apparent activation energy for creep,

Jan 1, 1970

By F. E. Steigert, A. H. Geisler

THE permanent magnet alloy comol, which contains 17 pct Mo, 12 pct Co, balance Fe, exhibits a precipitation reaction analogous to that at the iron end of the binary Fe-Mo system. The equilibrium precipitate, (P,), has a structure isomorphous with Fe,Mo, which is rhombohedra1 with parameters a = 8.97A and a = 3038.6&apos; according to the work of Arnfelt and Westgren.&apos; In the ternary alloy the parameters are a = 8.87A and a = 31°0.5&apos;. Oscillating crystal patterns of a single matrix crystal, M, in which P, was precipitated by slow cooling from 1300°C, showed that the orientation relationship of the two lattices is as follows: (110)P3 // (110)* (111)p3 // (110)m There are crystallites of P, in 12 different orientations in a single crystal of the parent solid solution. Microscopic examination shows that the crystallites are generally plate-like with their lateral dimensions parallel to (110) matrix planes. When precipitation in a supersaturated alloy quenched from 1300°C progressed isothermally at temperatures between 600" to 800°C, the evolution of the P, structure could be traced. Diffuse diffraction effects in Laue patterns provided early evidence of the precipitation process. Analyses of these by a previously described technique2 showed that they corresponded to rod-like elements parallel to <110> matrix directions in reciprocal space. With further aging to promote growth of the precipitate, the rod-like elements contracted to points in reciprocal space for normal Bragg reflection from the precipitate as shown by the left diagram in Fig. 1. Thus the diffuse scattering was attributed to the small thickness of the plate-like particles which was inadequate for sharp diffraction. When the precipitate particles were first thick enough to give normal diffraction their structure was different from that of the equilibrium precipitate, P,. The first structure, P1, presumably is a coherent transition struc-

Jan 1, 1952

By AIME AIME

LIFE will not be difficult for those who attend the fall meeting of the Petroleum Division at the Conoco Club, Ponca City, Okla., Sept. 30-Oct. 1. An attractive program to appeal to oil company executives and lawyers, as well as technologists, has been arranged and the Continental Oil Co. has contributed for the occasion the buildings, grounds and facilities of the club. E. 0. Bennett, Continental Oil Co., Ponca City, is chairman of the arrangements committee, and reservations for rooms and trips, requests for information, etc., should be sent to him.

Jan 1, 1932

By Colin G. ink

OUTSTANDI&apos;NG in progress among the less familiar &apos;metals during 1936 is the electrolytic production of 99.9 per cent manganese meta1 readily and many quantity. Strictly speaking, manganese should not&apos; be classed as &apos;a rare metal, since there is 800 times as much manganese in the earth&apos;s crust as there is zinc or lead. But manganese&apos; as a metal is rare, just as titanium metal is rare though titanium is five times as abundant in the earth&apos;s crust as manganese.

Jan 1, 1937

By W. E. Brigham, P. W. Reed, J. N. Dew