Search Documents

By F. Weinberg

It has been suggested, for some time, that the behavior of metals under high-temperature creep conditions is strongly influenced by the behavior of the grain boundaries present in the material. This has led to a number of investigations1-6 in which attempts were made to measure the properties of the grain boundaries themselves, both to determine their contribution to the creep process and to obtain further knowledge of their intrinsic structure and properties. The present investigation was undertaken to extend the observed data under more closely controlled experimental conditions and to attempt to clarify sonie of the discrepancies in the literature. A brief report of the preliminary results has been published.7 EXPERIMENTAL PROCEDURE For the present investigation, controlled orientation specimens were used having plane boundaries which terminated at the specimen surface. Trierys-tal specimens were used instead of the bicrystal type of Puttick and King,' in order to simplify the gripping technique required to apply a shear stress along the boundary. The aluminum used was obtained from the Aluminum Francaise and was of 99.994 pct purity, containing 0.002 pct each of Cu, Fe, and Si. The aluminum tricrystals were grown horizontally from the melt, in graphite boats, and in an argon atmosphere, following the technique developed by Chalmers.' The orientation of the tricrystals was controlled by using seed crystals separated by mica inserts. Thermal conditions were adjusted to produce tricrystals having boundaries which were macroscopically straight, parallel to the growth direction, and perpendicular to the top surface. Following growth, the tricrystals were carefully cut with a jeweller's saw to the test specimen shapes shown in Fig. l(a) and l(b). In Fig. 1(a), the boundaries subjected to shear stresses are indicated AB and CD: Points A and C are the ends of the mica inserts separating the seed crystals; points B and D are at lateral cuts made in the specimen. It was found that the slots left by the mica inserts at A and C had to be enlarged slightly, by cutting, to ensure that the boundary terminated freely at these points. A shear stress was applied to the boundarks by gripping the upper two legs in file-faced Inconel grips and suspending a weight from the lower part of the specimen held in similar grips, as shown schematically in the diagram. The test specimens shown in Fig. 1(b) were cut from long

Jan 1, 1959

By D. N. Seidrnan

In the present note we present thermal-analysis data for the liquidus curve from 0 to 76 at. pct Se and for the selenium-rich monotectic reaction in the Pb-Se system. We have previously reported that no expey-imental eviderzce was found for a lead-rich monotectic reaction, at -860°C with a monotectic composition of -20.5 at. pct Se, as found by Nozato and Igaki.&apos; Our additional data substantiated this earlier finding and extended the composition range studied. The alloys were prepared from semiconductor -grade lead and selenium purchased from the American Smelting and Refining Co. Both elements were 99.999+ wt pct pure as determined by the supplier. The impurities for lead were Fe (1 ppm) and Cu & ppm) while for selenium the impurities were Cu (< 1 ppm), As (< 1 ppm), Te (1 ppm), and C1 (<1 ppm). The general procedures used for thermal analysis were those specified by the National Bureau of Standards. A Pt/Pt-10 pct Rh thermocouple calibrated against the freezing points of zinc and copper purchased from the National Bureau of Standards and antimony (99.985 pct pure) purchased from A. D. Mackay, New York, was used for all the thermal analysis. The thermocouple electromotive force was measured with a Rubicon Type B potentiometer used in conjunction with a galvanometer with a sensitivity of 0.5 pV (mm) -&apos;. The absolute accuracy of this thermal-analysis system was *0.5"C. One-hundred-gram alloys of the desired composition were sealed in quartz crucibles, with a central thermocouple well, at a pressure of less than 10"1 Torr. The alloys were initially heated well above the liquidus curve and shaken vigorously to insure homogeneity. Cooling curves were then taken by the direct method at cooling rates ranging from -0.5" to 1.5"C (min)-&apos;. The phase diagram from 0 to 76 at. pct Se as determined by direct thermal analysis is shown in Fig. l.* An extrapolation of the selenium-rich portion of the liquidus curve to the monotectic reaction isotherm (678.3"C) gave a value of 76.1 at. pct Se for the monotectic composition. A tabulation of all the thermal-analysis data is given in Table I. As we previously reported no experimental evidence was found Fig. l—The partial Pb-Se phase diagram from 0 to 76 at. pct Se as determined by direct thermal analysis. For the sake of clarity the points for the 49.00 and 49.16 at. pct Se alloys were not drawn on this phase diagram, see Table I. for the lead-rich monotectic reaction found by Nozato and Igaki.&apos; This result was further substantiated by the fact that none of twelve lead-rich alloys, see Table I, examined for this monotectic reaction exhibited a thermal arrest in the temperature range (849" to 863°C) cited by Nozato and Igaki for the lead-rich monotectic reaction. Hence, our results tend to support the earlier qualitative work of ~elabon&apos; and Friedrich and ~eroux" in the 0 to 50 at. pct portion of the phase diagram, though the selenium-rich monotectic composition and reaction isotherm temperature were in agreement with the approximate values (75 at. pct Se and 672" to 680°C) given by Nozato and ~~aki. &apos;

Jan 1, 1967

By W. Rostoker, R. P. Elliott, B. W. Levinger

Phase equilibria in the Ti-Mn-Mo system have been investigated in the composition range 100 to 60 pct Ti and in the temperature range 550 to 1150°C. Three out of ten isothermal sections are presented as well as seven vertical sections, projections of the beta space and the surface of incipient melting. A STUDY of the system Ti-Mn-Mo was undertaken as part of a program to aid in the development of titanium-base phase equilibrium diagrams of potential technical importance to alloy development. The scope of the investigation included the composition range 100 to 60 wt pct Ti (all compositions refer to weight percentages) and the temperature range 550" to 1150°C. A surface of incipient melting was constructed from measurements of a large number of alloys. In the binary system Ti-Mo,&apos; the high temperature modification of titanium generally spoken of as the p phase is stabilized to successively lower temperatures with increasing alloy content. There are no known intermediate phases, and complete miscibility exists between body-centered cubic titanium and molybdenum. The u solid solution is limited to less than 0.8 pct Mo at temperatures between 885" and 600°C. An equilibrium diagram for the binary system Ti-Mn has been published.&apos; Manganese behaves as a p stabilizer but undergoes a eutectoid transformation at about 20 pct Mn and 550°C to a plus an intermediate phase. The structure of this phase has been found to be isomorphous with the a phase FeCr." Accordingly, the phase is assigned the formula TiMn, although its actual location on the composition scale has not been determined and may well be not exactly at the equiatomic composition. In disagreement with ref. 2, the origin of the TiMn phase has been shown&apos; to be a peritectoid transformation at a temperature between 900" and 1000°C. A second intermediate phase occurs at the atomic proportions TiMn,. The structure of this phase was originally established by Wallbaum" as having a hexagonal lattice (C 14 type, 12 atoms per unit cell) isomorphous with MgZn,. In this work, the structure determination was confirmed and lattice parameters determined to be: a = 4.815 kX, c - 7.901 kX. Because of the extensive range of the P phase, the ternary system was suited to the determination of the phase boundaries by the parametric method of Andersen and Jette." During the course of the investigation, this method was found applicable only to the P/a+P boundaries but not to P/P+ compound boundaries. Metallographic methods were used alternatively for delineating these phase boundaries. Preparation and Treatment of Alloys Over 70 alloys were prepared for the study of this system. Ten gram alloy buttons were arc melted in a nonconsumable electrode furnace using inert atmosphere protection, and a water cooled copper crucible. The construction and operation of this type of melting unit has been described.&apos; To insure complete solution of alloy additions, especially molybdenum, the buttons were remelted alternately on top or bottom as many as five times. This was accomplished by a suitable mechanism for "flipping" the ingots over. It was very difficult to obtain homogeneous melts in the region of less than 75 pct Ti because of the very high melting point of molybdenum and Ti-Mo master alloys and the comparatively low boiling point of manganese. Thus, the arc conditions for insuring complete solution of molybdenum were incompatible with the prevention of heavy losses of

Jan 1, 1955

By J. Gordon Parr, D. H. Polonis

IN a previous study of hypereutectoid Ti-Ni alloys&apos; a substructure was observed in quenched powder specimens when the constitution was 100 pet retained ß body-centered-cubic phase. The alloy powders were quenched from 1000°C by a blast of helium gas and precautions already described were observed throughout the work, to minimize contamination. Ogden et al.2 have previously observed subboundaries in the ß phase of a Ti-Mn-N alloy; but this structure was attributed to nitrogen-rich a precipitation. The nitrogen content of the Ti-Ni alloys does not exceed 0.02 pet and the quenching rate was sufficiently rapid to suppress precipitation reactions. Since X-ray diffraction results have confirmed the absence of any second phase which might account for this phenomenon, it seems unlikely that this substructure is explicable in terms of nitrogen content. Fig. 1 shows the substructure in adjacent grains of 100 pet ß phase in a quenched 6 atomic pet Ni alloy. Fig. 2 shows adjacent ß grains in a similarly treated alloy; one grain contains marked intracrys-talline boundaries and the other is completely free from any substructure. The suberystals appear to have fairly regular shapes, suggesting a regular orientation relationship among them. Tempering the retained ß structure at temperatures below the eutectoid eliminates the substructure at an early stage of ß decomposition. At the present time it is possible only to guess at an explanation for this subboundary phenomenon, since very little work has been reported on substructures resulting from phase changes. It is believed that the present phenomenon is due to poly-gonization resulting from unrelieved stresses set up

Jan 1, 1957

By AIME AIME

PRIZES totaling $450 were awarded at the Annual Meeting luncheon on Monday, Feb. 9, to the winners of the third national student prize paper contest. The undergraduate prizewinners, each of whom received a check for $100, were as follows: Mayo W. Lanning, Lafayette College, for his paper entitled ?Some Aspects of the Mining Methods Employed at the Scrub Oak Mines of the Alan Wood Steel Company,? (entered by the Lehigh Valley Section). Charles F. Parent, Montana School of Mines, for his paper entitled ?Relationships of Manganese Minerals in the Butte District,? (entered by the Montana Section). Harry Czyzewski, University of Illinois, for his paper entitled ?A Metallurgical Study of Cast Irons Used for Glass Molds,? (entered by the Chicago Section).

Jan 1, 1942

By O. G. Lellep

Modern shaft kilns in Europe are fully mechanized and burn cement of acceptable quality at 700,000 Btu per bbl and lime at 3.2 million Btu per net ton. Rotary kilns for cement have increased in thermal efficiency by using exit gas heat for preheating incoming raw material and by recovering heat from outgoing clinker in air-quench coolers. The dry process Lepol or ACL kiln has the lowest fuel consumption, 580,000 to 630,000 Btu per bbl, and very low dust loss, about 1 pct weight of clinker. The Holdebank-Gygi system reaches 720,000 Btu per bbl. The calcinator kiln for the wet process consumes 1.1 million Btu per bbl. IN every country economic circumstances prescribe the method used to produce a commodity at lowest cost. In Pennsvlvania a man&apos;s wages for working 4 hr buys a ton of coal wholesale; in Germany a laborer must work 40 hr, or ten times as long. In western Europe, therefore, conservation of fuel is of primary importance, and recent practices of burning lime and cement differ from those employed in the United States. &apos;This Paper presents data collected during a trip through western Europe in 1953. Considered uneconomical, shaft kilns for burning

Jan 1, 1955

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By J. L. Schroeder, W. G. Talman

EXPERIENCE has shown that certain known natural conditions and other indefinite characteristics combine to make a mining area vulnerable to mountain bumps. Some of the known conditions are heavy overburden, an overlying stratum of strong non-elastic rock, a structurally strong coal seam that does not crush easily and yet is the weakest stratum in the series, and a floor stratum of more than ordinary firmness. The indefinite characteristics could include resistance of top or bottom of a coal seam to lateral flow, effect of immediate top and bottom strata, nature of the coal seam, and other factors about which very little is known. It is in this area that exhaustive study is needed to achieve positive control of the dreaded mountain bump hazard. In the Gary district, West Virginia, two of the five operating mines have areas known to be vulnerable to mountain bumps.These are the No. 2 and 6 mines, which are working the Pocahontas No. 4 coal seam. In this area the seam is overlain at a zero to 10-ft interval by the massive Eckman sandstone, which is about 100 ft thick in the vulnerable areas. Total overburden, consisting of shale, coal seams, and sandstones, ranges from 700 to 1400 ft where bumps have occurred (Fig. 1). The coal seam is 4 to 8 ft thick and has a weak columnar structure of very soft and spongy or woody coal. The immediate top is either the Eckman sandstone or hard shale, both of which provide generally good roof conditions for mining operations. The bottom ranges from medium to hard gray shale. The incidence of bumps in the Gary district dates from about 1930 and can be correlated to some degree with the increased rate of extraction attained with mechanical mining. During early years of operation at the No. 2 and 6 mines, most of the work was development and under comparatively light cover. As overburden became heavier, together with an increasing percentage of coal coming from pillar extraction, mountain bumps began to occur. Before 1945 they were much less severe than in later years, and because there were no injuries or fatalities, no records were kept. But by 1951 the incidence of bumps had increased to such extent that it became evident a mining system would have to be designed to eliminate or at least minimize these occurrences. Drawing on experience with modified versions of old systems and certain characteristics peculiar to the Pocahontas No. 4 coal seam, the district mining engineer, Martin Hayduk, outlined the essential factors for bump control in the Gary district. These control factors indicated: 1) The highly stressed area, which lies within the limits of convergence effects, moves at approximately the same rate as the retreating pillar line. 2) There is a decided softening of the periphery of blocks which is greatest and deepest on the gob side. 3) Blocks less than 45 ft wide never have been known to bump in the Pocahontas seams. Fig. 2 shows the mining plan based on these observations—a thin-pillar system with a minimum of secondary development. It was recognized from the start that the Hayduk system had certain limitations. When pillar work backed up to an inevitable surrounded block it was no longer applicable; also, burnt bottom and/or unknown factors reduced the system&apos;s effectiveness in certain headings. Since there was no way to eliminate the loaded block, it was decided to experiment with auger drilling to attain controlled release of this stored-up energy. The decision to auger was made after consideration of three separate plants, which were: 1) To cut the solid block into pillars of maximum size by driving away from the fracture line and at such a distance outby that development

Jan 1, 1959

By Austin E. Dwight

IT has been shown by Oelsen and Wever&apos; that the effect of a solute element on the allotropic transformation in iron is dependent upon the quantity

Jan 1, 1957

By GILBERT C. DAVIS

ANY thought of Morenci naturally includes its sister town of Clifton, its gateway to the outside world. Clifton, the country seat of Greenlee County, is the terminus of a branch line of the Southern Pacific railroad from Lordsburg, N.M. Carload freight incident to the Morenci operation moves from Clifton over Phelps Dodge?s standard-gauge industrial railroad. Private freight must be hauled by truck. These two communities fell far short of supplying adequate housing for the personnel concerned with the new operations so a new townsite, Stargo, was developed adjacent to Morenci. Here 234 housing units with garages have been built and twenty similar units have been erected near the reduction works.

Jan 1, 1942

By T. S. Fuller

MUCH study has been given by engineers in general, and investigators in particular, to the concentration of stress which occurs under load in structural members having irregularities in section such as notches, shoulders, key ways, tool marks, etc. The result of the effect of both fresh and salt water corrosion upon the endurance properties of various metals and alloys has been ably determined and the general laws underlying these phenomena carefully pointed out by McAdam. From a practical standpoint, &apos;however, it is after all the endurance value of corroded, non-symmetrical sections which is most pertinent. In the experiments about to be described rotating cantilever specimens of nickel steel of the 3.5 per cent nickel &apos; 0.35 per cent carbon type have been used. These were machined from bars l 1/8. in. dia. and 9% in. long and were heat-treated by quenching in oil from 825 deg. C. followed by reheating to 650&apos; C. and oil quenching. The tensile and impact properties of this material so heat- treated follow:

Jan 1, 1931

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By Dogan E. Gücer

In the following note, with the help of a new parameter of strain hardening, the attention is drawn to the close relationship between the relative performances of steels under plastic range cycling and their strain hardening characteristics. If a cantilever beam of rectangular cross section is tested with the arrangement shown in Fig. 1 in reversed bending between constant deflection limits at the lever head, the longitudinal strain-deflection hysteresis shown in Fig. 2 is obtained. There is no lateral strain due to constraint at the rectangular test section.&apos; If the absolute value of strain undergone between a maximum state of tension and maximum state of compression is called A, it will be seen that A decreases with cycling rapidly due to the strain hardening in the test section and the ensuing change in the bent beam profile. It will also be seen that A reaches an approximately stable value around 10th cycle. If we call the first cycle strain range, A,, and that of 10th cycle, A,,, then is an index of the strain hardening capacity at a particular deflection level. A plot of n vs ? is reproduced in Fig. 3 for two ASTM steels: A-302 and A-201. A-302 is a low alloy structural steel, A-201 a low-carbon steel. The specimens were first normalized at 1650°F for 75 min then grooved with a milling cutter; and the notches were ground to 50G finish. The final operation before testing was a stress relief at 1150°F for 75 min. The behavior of the two steels changes around ?1 = 0.8 pct or A,, = A, -n = 0.7. If these curves are compared with the endurance life curves given in Fig. 4, it will be seen that the relative performance of the two steels also change around A,, =. 0.70 pct. The steel with lower strain hardening capacity (7) at a certain strain level shows a longer endurance life, irrespective of their strength levels. Since the exponent governs strain hardening at lower strain levels than the Modulus, the relative values of both parameters also coincide with the change in n values and the relative performances of the two steels at different strain levels. These two observations indicate to the close relationship be-

Jan 1, 1962

By Harry Seltz, J. C. DeHaven

InteRmetallic compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455&apos; C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52, b = 8.60, c = 4.16 A.&apos; There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO² = CdO + CO + Sb From the known free energies of formation of CdO, CO² and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell reaction is the reversible formation of the compound from the elements. The first method is generally applicable, but requires elaborate experimental equipment. The second method can not be used for compounds melting at low temperatures, owing to the difficulty in establishing equilibrium. The electromotive force method, therefore, seemed to offer

Jan 1, 1935

By J. C. DeHaven, Harry Seltz

InteRmetallic compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455&apos; C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52, b = 8.60, c = 4.16 A.&apos; There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO² = CdO + CO + Sb From the known free energies of formation of CdO, CO² and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell reaction is the reversible formation of the compound from the elements. The first method is generally applicable, but requires elaborate experimental equipment. The second method can not be used for compounds melting at low temperatures, owing to the difficulty in establishing equilibrium. The electromotive force method, therefore, seemed to offer

Jan 1, 1935

By C. A. Stiles, J. W. Nyhus

Erie Mining Co. is a 10.3-million-tpy pellet producer on the east end of the Mesabi Range 60 miles north of Duluth. Its complex includes facilities for mining, crushing, grinding and beneficiation in addition to a pellet plant and power plant. A 74-mile railroad links the mine and plant to Taconite Harbor on the shore of Lake Superior. The concentrate recovery ratio at Erie is about 1: 3, and this, along with stripping activity, makes it necessary for the company to mine nearly a million tons of material a week. At the outset, all crude ore mined at Erie was hauled entirely by rail, but with expansion into additional mining areas, the company made a gradual transition towards truck-to-rail haulage. Today, in Erie&apos;s 11th year of operation, over 50% of all crude taconite mined is transported by truck to loading pockets where it is transferred to rail cars. Future years will see more taconite moved in this manner. Thus, the company has an increasing interest in tire performance.

Jan 6, 1969

By E. T. Turkdogan, Klaus Schwerdtfeger

OelSEN and Maetz1 detected some 20 years ago the existence of a miscibility gap in iron oxide-CaO-P2O5 slags melted in iron crucibles at about 1400°C. Because of the importance of this system for the dephos-phorization of steel in the basic Bessemer process, equilibria between liquid iron and selected iron oxide-CaO-P2Q slags have been measured since by numerous investigators.2-5 When in equilibrium with metallic iron, the iron oxide of the slag is present mainly as FeO. In connection with oxygen-blowing steelmaking processes, it is useful to know the phase relations in the slag system at higher oxygen pressure, when major parts of the iron oxide are present as Fe2O3. This problem was investigated by Turkdogan and Bills7 by equilibrating the oxide mixtures contained in platinum crucibles with CO2-CO mixtures at 1550°C. It was found that increasing the Fe2O3 content decreases the composition range of the miscibility gap strongly so that the miscibility gap has almost disappeared at pco2/pco = 75. This result was refuted by the careful work of Olette et a1.,&apos;&apos;&apos; who equilibrated their slags with controlled Ha-H2-Ar gas mixtures. Their equilibrium measurements, at 1600°C and at oxygen pressures of 5 x 10"* and 10"5 atm, showed that the oxidation state of the iron has almost no influence on the formation of the miscibility gap. The present experiments were undertaken to check the previous results of Turkdogan and Bills. The experiments were performed at 1625°C in the strongly oxidizing atmosphere of air (PO2 = 0.20 atm) for which no experimental data are available. About 10 g of slag were melted in platinum crucibles and held at constant temperature for 1 hr. After equilibration, the crucible was rapidly pulled out of the furnace and cooled in air. The platinum crucible was removed from the sample. The two slag layers were carefully separated with a small diamond disc, and the surface of the top layer, which may have changed its oxidation state during cooling, was removed. The slags were crushed and analyzed chemically for CaO, P2O5, Fe2+, and Fetotal. The starting mixtures were prepared by sintering the desired amounts of reagent-grade 2CaO . P2O5 - H2O, CaCO3, and Fe2O3. Sintering and subsequent crushing were done three times to ensure homogenization. Molybdenum wire resistance heating was used. The furnace was provided with a recrystallized alumina reaction tube which was left open to air at the top. The temperature was controlled electronically. The reported temperature was measured with a Pt/Pt-10 pct Rh thermocouple and is estimated to be accurate within +5°C. The composition of the equilibrated melts is given in Table I. For the graphical illustration of these quaternary slags the type of projection suggested by Trömel and Fritze10 was used. In this representation, Fig. 1, the composition point of a mixture within the tetrahedron Fe2O3-CaO-P2O5-FeO is projected into the Fe2O3-CaO-P2O5, triangle (triangle I) so that the direction of projection is parallel to the side FeO-Fe2O3, and into the triangle Fe2O3-P2O,-Fe0 (triangle 11) so that the direction of projection is parallel to the side CaO-P2O5, of the tetrahedron. The projected point has the coordinates wt pct CaO, wt pct P205, and wt pct (FeO + Fe2O3) in triangle I and wt pct FeO, wt pct Fe2O3, and wt pct (CaO + PzO5) in triangle 11. Both triangles are turned into the same plane around the Fe203-P20, side of the tetrahedron. An illustration of the projection of a quaternary point in the present system is shown in Fig. 1. The advantage of this type of projection is that all four components for an equilibrium curve can be read directly from the diagram. The present results are shown graphically in Fig. 2. The curves depicting the miscibility gap are dashed in parts where no experimental points were obtained. The composition range covered by the miscibility gap

Jan 1, 1968

By G. A. Reinhardt

THE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4 in. (14.5 cm.) square bloom to a ¾ in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900 ° to 950° C. and cooling slowly in mica. The test bars were tempered by heating to 825° to 875° C., quenching in water, and drawing to 515° to 535° C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. ULTIMATE STRENGTH, ELONGATION, LB. PER SQ. IN. PER CENT. IN 4 IN. NOT LESS THAN Annealed specimens 78,230 to 92,450 18 Tempered 120,000 to 149,350 9 After experience oil this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850° to 900° C. and cooling in still air; the annealing, in heating to 850° to 900° C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were:

Jan 7, 1919

By R. H. Widmyer, G. M. Wood

This investigation was prompted by the absence of a simple, accurate method to predict optimum second stage separation pressure in three stage separation operations. Three stage separation as used here includes two separators plus the stock tank. The first stage pressure is usually fixed by gas sales conditions and the third stage is at atmospheric pressure. Thus, the second stage pressure is the only one that may be varied in-discriminantly during production operations. No variations in temperature were considered in this study, even though it will vary among systems, for a change in temperature has little effect on the optimum pressure. Optimum pressures may be determined from flash calculations, but these are tedious unless a computer is available. An early attempt to develop a simpler method&apos; yielded an equation which gave the optimum pressure only as a function of initial and final pressure. Experience, however, confirms theoretical relationships which show that composition as well as pressure and temperature must be a factor. This indicates that the basic relationship should be an equation of the form, where P, is second stage pressure, P, is first stage pressure, A is a function of P. (stock-tank pressure) and the system composition, and n is a function of the number of stages and the system composition. Fig. 1 shows the basic variation of P2 with P for a fixed system composition. A series of such figures clearly showed the effect of composition. The peak of each curve reflects that second stage pressure at which the stock-tank recovery (gal/MMcf) residue gas is a maximum value. DEVELOPMENT OF NEW CORRELATION Wellstreams having 17 different analyses, ranging from low gravity crude to condensate, were used to determine the effect of composition. Each wellstream was flashed through three stages to determine the optimum second stage pressure for each first stage pressure. Equilibrium vaporization ratios proposed by Latham and Campbell were used throughout. The heptane plus fraction, for simplicity, was assumed to have the properties of octane. The results were subjected to an empirical analysis in an attempt to develop a correlation- that would be (1) simple, (2) accurate, and (3) eliminate the need for any flash vaporization calculations. This analysis yielded two equations, one for wellstreams having a specific gravity greater than one (air = 1.0) and one for those less than one. For crude streams (specific gravFor condensate (specific gravity < 1.0),