Search Documents

INCREASING realization that pouring and ingot-mold practices involve many factors of fundamental importance to ingot quality and general steel-mill operations has caused these phases of steelmaking to become major concerns of operators and metallurgists engaged in control of quality and costs. Methods of pouring steel from the ladle into the ingot molds have some direct effects on ingot quality. The mold itself governs solidification and dimensions of the ingot and in so doing exerts some very tangible influences not only on ingot quality but also on product yields and general steel-mill processing. In addition, practices are employed' in the handling of molds during daily open-hearth operations that are important to quality and production costs. Therefore, pouring and mold practices must be considered highly specialized and important steps in steel-mill operations. MOLD DESIGN Mold design is difficult to discuss in a precise manner because it varies greatly throughout the industry, both in theoretical concepts and practical application, and few well developed data are available. Most ingot molds are designed to meet conditions peculiar to a given plant wherein quality standards are dictated by end-use requirements, which may differ considerably, even for the same grade of steel. The mold designer must also consider the equipment available to process ingots and the product obtained from them. Such equipment, used for stripping, heating, blooming and finishing operations, is seldom, if ever, exactly the same in any two steel plants. Thus, pronounced contrasts in mold designs can be expected to continue, even among plants making strictly comparable types of product, particularly because some producers are just beginning to realize the benefits possible from specialized designs. Certain fundamentals are used in mold design but even these

Jan 1, 1951

By E. F. La Vigne

ON Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Co. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about ½ mile south of the original shaft and plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-lined shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erected. This new plant began opera-tions on Dec. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours.

Jan 1, 1936

By Arthur B. Yates

Diamond drilling has advanced and expanded during the past few yean. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. Control A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing— even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved. however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the

Jan 1, 1946

By R. M. Brick

The etched mierostructures of cold-worked alpha brasses, after reductions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonymously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {ill), in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans' results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson6 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into symmetry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

By R. M. Brick

The etched mierostructures of cold-worked alpha brasses, after reductions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonymously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {ill), in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans' results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson6 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into symmetry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

By AIME

One of the operations of the J. L. Shiely Co. is quarrying in a hard granite gneiss with intrusions of gabbro or trap. During the winter of 1948-1949 the quarry ramp was lowered about 30 ft and during the 1949 season practically all drilling was done from the quarry floor, developing a face from 72 to 83 ft for the entire quarry area. The performance and cost table shows our record for 1948 and 1949.

Jan 1, 1950

By John T. Eash

During the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. Selection or Composition While the final criterion of the suitability of an alloy for a bearing must of course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstruc-ture, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig' 1. I' In the tin bronze contains the hard alpha + delta

Jan 1, 1946

By John T. Eash

During the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. Selection or Composition While the final criterion of the suitability of an alloy for a bearing must of course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstruc-ture, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig' 1. I' In the tin bronze contains the hard alpha + delta

Jan 1, 1946

By Richard H. Jahns

Gem materials, comprising those minerals and closely allied natural substances used for personal adornment, for the fashioning of ornamental objects, or for other decorative purposes, have been valued in human commerce for thousands of years. Amber, jet, natural glasses, and at least 15 mineral species were sought and used by primitive man, and most of the materials in common use today were known well before the time of Christ. Their variety is remarkably great, and the traceable relationships among their respective sources, modes of occurrence, properties, and histories of production, preparation, and valuation are extremely complex. Their uses have been affected by numerous shifts in fashion, and from time to time by superstition, by decrees of church and state, by personal interpretations of religious significance, and by various presumptions concerning medicinal value and influence on human behavior (Ball, 1935, 1950; Kunz, 1913; Pogue, 1915, Whitlock, 1946). Thanks to their durability, portability, and relative scarcity, some gem stones have been employed as media of exchange, and the investment value of the more precious stones has long been recognized and exploited, especially in Asiatic and European countries. Demands for gem materials have stimulated trade among various peoples for centuries, and they also were responsible for much early geographic exploration. During more recent times they have prompted numerous geological studies and a considerable amount of research on the growth and properties of crystals. Apart from decorative uses, some naturally occurring gem materials also are employed directly in numerous fields of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater intrinsic value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconsistent, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Substances that lose their identity in use are excluded from the gem category; thus a transparent crystal of beryl would not be classified as a gem stone if it were processed as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means for distinguishing different gem materials on the basis of recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquoise, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of specific properties, and now all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semi- precious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance

Jan 1, 1975

By Ernest F. Burchard

MOST of the iron ore smelted in Alabama blast furnaces is mined within Alabama, although deposits in the neighboring States of Georgia and Tennessee may be drawn upon when occasion requires. Of the four commercial kinds of iron ore, the anhydrous ferric oxide, hematite (Fe2O3) ; the hydrous ferric oxide, mostly the type commonly known as limonite (2 Fe2O33H2O) ; the carbonate, siderite (FeCO3) ; and the magnetic oxide, magnetite (Fe:3O4) ; the first two are found in abundance in Alabama, the third in less than commercial quantities, and the fourth only rarely. Both the hematite and the hydroxide are found in somewhat different forms according to their geologic environment. The Red Mountain hematite, of Silurian age, that crops out in well¬defined beds for 1.50 miles northeast-southwest and 40 miles northwest-southeast is the predominant source of ore. Only a small part of this area carries ore of commercial value; Birmingham and Gadsden are now the only centers of production. The ore is of sedimentary origin, probably altered from vast deposits of greensand mixed with calcareous, fossiliferous. marine debris. Other types of hematite not vet mined commercially are in metamorphosed rocks-red ore in slates in Columbiana Mountain and specular hematite (gray ore) in quartzite in the Talladega Hills.

Jan 1, 1938

By Thomas M. Price

Sand production for use in hydraulic concrete is probably the most important element affecting the physical characteristics of the resulting concrete in the opinion of most engineers, aggregate producers and contractors of today, who are engaged in the effort to produce stronger concrete per unit of cement used. Their opinion is based on both laboratory and field results. In the past, proper cement production has been the object of most of the study given this subject and while it is still studied by the extensive and well equipped laboratories that are a part of every cement mill, as well as by all governmental laboratories, at the present time the object of most of these studies has been in the field of low heat and quick setting qualities rather than the effect on the strength of the concrete. It is recognized that concrete must have two important qualities; namely, workability with the least water possible, and uniformity. These qualities have been accepted as axiomatic and possible to obtain if the foreman in charge knew his business. Now, however, with concrete produced by plants that mechanically weigh and chart all the ingredients, including water, of a batch of concrete, the foreman cannot cut and fit his aggregates, cement and water to fit his own desires and the secret of the important qualities of workability and uniformity are found to lie largely in the sand, hence the attention given its production at the present time. With this condition in mind the engineers of the United States Bureau of Reclamation and the Six Companies Incorporated in designing the plant for producing the aggregates for the Boulder Canyon Project included every possible means for the production of a sand of a constant and acceptable fineness modulus as well as a constant moisture content, and for attaining these results with as few detrimental ingredients, like silt and vegetable matter, as possible. This aggregate plant (Figs. 1 and 2) is in Hemenway Wash, 7 miles north of Boulder City. It is 4 miles upstream from the low-level mixing plant. At this screening plant 8,234,000 tons of raw aggregate are being

Jan 1, 1934

By William E. Greenawalt

Ever since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydroelectric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods. Electrolytic methods are ideally adapted to hydroelectric development, for the load is constant throughout the full twenty-four hours, and the cost of both installation and operation of hydroelectric plants is not appreciably greater when operating for twenty-four hours than when operating for eight or ten hours; whereas, in fuel-power generation, as also in smelting, the cost is more or less in proportion to the fuel and power used. Nevertheless, fuel-power generation presents advantages in electrolytic methods, as the power plant may be located in a favorable place while the leaching and electrolytic plants may be located at the mine. The ultimate possibilities of the wet methods have yet to be determined. The possibilities of smelting have been thoroughly worked out; there is no unsolved major problem in copper smelting, and it has practically reached the limit of its possibilities. It seems hardly probable that any future improvement, either of method or apparatus, will greatly

Jan 1, 1924

By A. Bauer, P. Calder, N. H. Carr, G. R. Harris

Since both rotary and jet piercing drills are used by the Iron Ore Co. at Smallwood, it is often desirable in planning to know in which regions of the orebody or new orebodies a particular drill will be the most economic. This makes it necessary to establish a correlation between drillability and pierceability and some physical rock properties. For rotary drills a good correlation was found with penetration rate and grinding factor index. The jet piercers were found to have a reciprocal relationship in the sense that the best rotary ground was the worst jet ground and vice versa. It is also indicated how an economic comparison could be made using these penetration rate versus grinding factor index curves, the hole size distribution curves for single pass and chambered holes and the mine distribution curve for grinding factor index. A discussion is presented on the fuel oxygen ratios to be used in jet piercing and on the site gas sampling and analysis which has been used to set up the drills. The fuel has been cut back so that stoichio-metric conditions exist, carbon monoxide is drastically reduced and pop-up or exploding holes eliminated. No decrease in penetration rate has been observed contrary to the published results of previous workers. The blasting procedure and results at Smallwood are discussed and the operation of Iron Ore Co.'s slurry pump-mix truck is also described briefly. Smallwood mine is part of the Iron Ore Co.'s Carol Lake operation and is situated in Labrador, 240 miles north of Sept-Iles, Quebec. Last year 15 million tons of crude ore were crushed to yield 6.3 million tons of concentrate and pellets. This year the figures will be 17 million tons of crude and 7% million tons of concentrate and pellets which is the full plant capacity. Carol Lake ores consist primarily of specularite and magnetite mixed with quartz. For convenience the ore has been split-into the following classifications depending on the percentage of magnetics in the sample, shown in brackets: specularite (0 to 10%), specularite-magnetite (10 to 20%), magnetite- specularite (20 to 30%), magnetite (>30%). The order of classification also represents the order of increasing grinding difficulty - the specularite generally being the easiest and the magnetite the hardest. The orebody also contains a small percentage of waste materials consisting of limonite carbonate, quartz carbonate and quartz magnetite. The first two materials are among the softest in the mine, generally softer than the specularite, and the quartz magnetite is amongst the hardest. The bulk of the material in the mine is of the specularite-magnetite and magnetite-specularite classifications. As a result of test drilling at Smallwood in 1960 with rotary, jet and percussion drills, the Iron Ore Co. purchased four JPM-4 jet piercers for the bulk of production drilling and set up an oxygen plant to supply 20 tons of oxygen per day. This oxygen is sufficient for two machines operating full time and one part time. In addition, there are two 50-R, one 60-R and one 40-R machines in use. The benches are 45 ft high and 50 ft holes are generally drilled. JET DRILLING At the onset of jet drilling in the late fall of 1962, two major problems were encountered: 1) freezing due to winter operations; experience and the use of heat at more places, such as the rotary head, has eliminated this,'" and 2) exploding or "popping" drilled holes; this happened frequently (several holes "popping" each day) and was the cause of two lost time accidents. In one instance a hole was being measured with a tape which fell down the hole causing it to "pop." Safety glasses though pulverized saved the wearer's eyesight. Various methods were then employed to detonate the holes before measuring or loading (dropping lighted rags of fusees down, or sparking across a spark gap). These methods were time consuming and far from completely successful. Consideration was given to the fuel oxygen ratio on the machines and what this would produce in the way of product gases. A fuel oxygen weight ratio of 0.35 which was quite oxygen negative was being used. Theoretically appreciable carbon monoxide would be produced at this fuel oxygen ratio. On the close down procedure of the jet which calls for low oxygen after flame out, oxygen would be left in the hole along with this carbon monoxide. This is an explosive mixture. The fuel oxygen ratio was cut back to stoichiometric

Jan 1, 1967

By J. H. Jackson, P. D. Frost, C. H. Lorig, L. W. Eastwood, A. C. Loonam

It is well known that for equal weights of material, thin sections of the lighter structural alloys are more resistant to buckling under a compressive stress than thin sections of more dense material. Therefore, structural parts having the same resistance to buckling stresses are generally lightest when they are made of magnesium alloys. Consequently, there is considerable interest in the development of strong alloys having densities equal to or lower than that of magnesium and strength-weight ratios equivalent to those of the strongest aluminum alloys. The development of commercial magnesium-base alloys has been very successful, and their importance among materials in the structural field has been amply demonstrated. However, an even wider structural application of magnesium alloys might be effected if improvements could be made in the cold rollability and cold-forming characteristics. Such improvements, along with production of less directionality in properties. could be effected if the hexagonal close-packed lattice of present alloys could be replaced with a cubic lattice. In 1942, a project, having as its objective the improvement of some of the characteristics of commercial magnesium-base alloys, was initiated at Battelle Memorial Institute under the sponsorship of the Mathieson Chemical Corporation. At that time, one of the authors,* then Chief Metallurgist for the Mathieson Chemical Corporation, postulated that the addition of lithium to magnesium in sufficient quantities to change the crystal structure of the resultant alloy from a hexagonal to a body-centered cubic lattice should produce a magnesium-rich alloy which would have the desired improvements in cold-working characteristics with less directionality in properties. To test this view, a series of alloys was made and was found to have many of the attributes that were predicted. The view that magnesium-lithium alloys were of structural interest was also held by others. In 1943 and 1945, Dean and Andersonl,² obtained patents on magnesium-base alloys containing from about 1 to 10 pct lithium, from about 2 to about 10 pct manganese, and the balance substantially all magnesium; and on magnesium-base alloys containing from about 1 pct to about 10 pct lithium, from about 2 to about 10 pct manganese, from about 0.5 to 2 pct silver, and the balance substantially all magnesium. They noted that an alloy containing 83 pct magnesium, 10 pct manganese, 5 pct lithium, and 2 pct silver could be cold rolled by any of the usual methods and that this alloy was considerably harder and stronger than most other magnesium-base alloys heretofore available. In 1945, Hume-Rothery, et al.,3 predicted that magnesium-lithium base alloys should be soft and ductile and that such compositions, to which was added a third element for the purpose of producing a precipitation-hardening type of alloy, should be ductile, strong, and lighter than magnesium itself. Hume-Rothery investigated the binary magnesium-lithium and ternary magnesium-lithium-silver equilibrium relations and criticized the existing equilibrium diagrams. The binary magnesium-lithium equilibrium diagram has also been investigated by Grube, Von Zeppelin, and Bumm, Henry and Cordiano, Sal'dau and Shamrai, Hof-mann,' and Shamrai.8 The work of most investigators agreed with that of Grube, whose constitution diagram is shown in Fig 1. From the standpoint of development of structural alloys, the room-temperature equilibrium relations are of great interest. An examination of Fig 1 reveals that, from 0 to 5.7 pct lithium, the existing phase is alpha, which is a solution of lithium in hexagonal magnesium. The boundary between the alpha, and alpha plus beta regions, occurs at a Mg/Li of 16.5, corresponding to 5.7 pct lithium by weight. Between 5.7 pct and 10.3 pct lithium, there exists a mixture of the alpha phase (lithium dissolved in hexagonal magnesium) and the beta phase (magnesium dissolved in body-centered-cubic lithium). The boundary of the alpha plus beta and beta regions occurs at a Mg/Li of 8.7, corresponding to a lithium composition of 10.3 pct. Much of the work described here was directed toward obtaining an alloy made up of a large proportion, or entirely, of the body-centered-cubic beta structure. In his early work, Loonam found that specimens of lithium-bearing alloys were very malleable. Ingots of alloys prepared at that time were extruded to 3/8-in. diam bars, and the mechanical properties and the effects of heat treatment were then determined. These data are given in Table 1. The outstanding ductility of the alloys, combined with their moderately high strength, evoked considerable interest.

Jan 1, 1950

By O. R. Bergmann

Two approaches were taken to obtain direct experimental evidence jar the existence oj a jet in the explosion-cladding pvocess: 1) direct observation of the claddirg jwocess by rtzeans ojf kig-h-speed photography using a fvartziiy catnera and 2) use of a plated-surface experiment in contribution with clzetrzical analysis. The framing-camera records showed clearly the presence of a jet it1 the form of what appears to be a line spray. The jet velocity is considerably highev than the detonation velocity arid in vacuum it is almost twice as high as the detonatiou velocily. The results jrorrz the plated-surface experiment also corzfivtned the preseizce of- a jet. The artzoutlt o,f etzergy dissipated in the jetting process was foundd lo be consislent with the basic theovetical model o/ the cladding mechanism.. MaNY reports on metal working with explosives have appeared in the literature during the last few yearsThis paper describes experiments concern- ing the mechanism of the explosive metal-cladding process. It has become increasingly important as a unique method for bonding metals and a typical cladding arrangement is shown in Fig. 1. A theoretical analysis of the mechanism of explosive bonding and a description of the nature and types of bond zones obtained was given by Cowan and oltzman." A further discussion of the basic principles of the process, a detailed description of the different bond-zone types, and extensive information on the properties and the applications of explosively bonded metals was recently published by Holtzman and cowan. " The process is now in commercial use by E. I. du Pont de Nemours & Co. The concept of the existence of a jet during metal bonding with explosives forms a central part in the theoretical analysis of the cladding mechanism described by Cowan and Holtzman When a layer of explosive is detonated on a metal plate that is separated from a second metal plate by a small distance the metal plate in contact with the detonating explosive is accelerated by the detonation pressure. An angle is established between the undeflected and deflected portions of the plate. Subsequently the deflected portion of the first plate collides with the second metal plate.

Jan 1, 1967

By Richard L. Gordon

Minerals long have been important commodities in international trade. As an inevitable result, the governments of the world have employed a wide variety of programs that affect the flow of trade. Roughly speaking, we may distinguish between the desire of more developed countries (MDCs) like the United States, western Europe, and Japan to control imports of minerals and the concern of less developed countries (LDCs), like India, about exploiting and exporting their minerals. The terminology used to describe different countries and the classification of specific countries into groups is unsettled and often changing. The poorest countries have been characterized as backward, undeveloped, underdeveloped, and developing. The problem seems to be in selecting a term that is both accurate and polite. Less developed seems, for reasons outlined by Hagen [pp. 51-57], the most convenient term. The borderline between an LDC and an MDC is always open to dispute. Objective measures are difficult to develop because of deficiencies in basic data, and enormous conceptual problems arise in making valid comparisons from even good data [see Hagen, pp. 7-28]. Thus, policies of the MDCs can be evaluated chiefly by using a few basic arguments for protectionist attitudes towards international trade. In dealing with the LDCs, a more far-ranging evaluation that covers general economic policy goals, the role of foreign investment, and the indirect effects of trade is required. This duality breaks down when trying to deal with the depressed areas in an MDC; here the issues are more akin to those associated with problems in an LDC. Similarly, variants of arguments used in LDCs appear in debates about foreign investments in MDCs. The whole discussion of minerals in LDCs, moreover, has obvious implications for MDCs like Canada and Australia. They, too, must face problems about the best utilization of their resources. THE RESTRICTION OF MINERAL TRADE BY DEVELOPED COUNTRIES[a] At least to some extent, the world's leading industrial nations have intervened to control the inflow of minerals. Such regulation is particularly pronounced for energy. Both the United States and western Europe employ

Jan 1, 1976

By N. Tiner

THE mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed commercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques, 1-4 and Achenbach, Nipper and Piwowarsky,5 based principally on thermal analysis, ascribe the grain-refining action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the effect of superheating on grain size of magnesium alloys. Attempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. The preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the .resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. PREPARATION OF SAMPLES AND GRAIN-SIZE TESTING The alloys investigated in this paper were taken from ingots made by Permanente Metals Corporation or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1945

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter (LID) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23% of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with LID ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests, a radial prestress of 3000 or 5000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3000 psi prestress, was 54.3% for limestone, 40.3% for marble, 44.7% for sandstone, and 23.4% for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5000 psi prestress, was 74.2% for limestone, 51.2% for marble, 61.6% for sandstone, and 29.7% for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room-and-pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent. One important objective of the U.S. Bureau of Mines (USBM) mining research program is the rational design of mining systems. In the design of room-and-pillar mining operations, pillar strength is a fundamental variable. It is customary to estimate this strength from uniaxial compression tests of rock samples and to correct this value for the length-to-diameter (LID) ratio of the in-situ pillar. This method of estimating pillar strength corrects for pillar shape but does not consider the effect of a large horizontal in-situ stress field that sometimes exists in underground formations. The purpose of the work covered in this report was to determine to what extent the compressive strengths of model pillars of relatively brittle rock loaded in axial compression were affected by lateral end constraint. In previous work, Obert l used solid steel rings bonded to the ends of dogbone-shaped specimens to study the creep behavior of three quasi-plastic rocks -salt, trona, and potash ore - during a test period of 1000 hr. These rings provided radial constraint during the loading cycle of 20 to 50% of the axial stress for specimens with LID ratios of 2, 0.5, and 0.25. He concluded that (1) "for a quasi-plastic material the end constraint strongly affects the specimen strength, and (2) as D/L increases (length-to-diameter decreases), the specimens lose their brittle characteristics and tend to flow rather than fracture." He also concluded that model pillars constrained by rings were better for use in predicting the strength of mine pillars than either cylindrical or prismatic specimens. This conclusion appears to be valid where mine pillars, roof, and floor are a single structural element. In the present study, 460 specimens of four relatively brittle rocks — limestone, marble, sandstone, and granite - were tested to failure. The study consisted of two parts: (1) the effect on the compressive strength of end constraint produced during the axial loading cycle by solid steel rings bonded with epoxy to the ends of the specimens, and (2) the effect on the compressive strength of increased end constraint produced in part by a prestress applied prior to axial loading and in part by lateral expansion of the specimen during the loading cycle. The first part of this study was reported in some detail earlier.2 EXPERIMENTAL PROCEDURE AND EQUIPMENT Model rock pillars of the sizes and shapes shown in Fig. 1 were broken in axial compression when the ends were constrained as shown in Fig. 2. he straight specimens were broken without ring constraint. The specimens of dogbone shape were broken with (1) solid

Jan 1, 1970

By Earl Hanson

FIRES in heavily timbered mines are disastrous, involving danger to both life and property. Some mines have been completely ruined or so heavily damaged that reopening them would not pay. Though few mines are entirely free from danger of fire, the risk is minimized by proper care and good design of plant. The Tintic Standard mine is at Dividend, Utah, in the famous Tintic mining district, about 60 miles south of Salt Lake City. The development of the mine was begun in 1907 by the late Mr. E. J. Raddatz and his associates. From the beginning, the work was hampered by high rock temperatures and the presence of high concentrations of rock gases such as carbon dioxide and nitrogen. Development work was carried on with great perseverance for nine years, and resulted in the discovery of ore in 1916. The total production of the Tintic Standard mine to Jan. 1, 1936, amounted to 1,664,388 tons of ore, having a gross value of .$61,996,719.

Jan 1, 1936

By Arthur B. Yates

DIAMOND drilling has advanced and expanded during the past few years. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. CONTROL A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing-even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved, however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the nearer the direction of the hole is to this ideal, the straighter it will remain. This, of course, is not always practical and in some cases is impossible. Usually such a

Jan 1, 1946