Search Documents

By Chingyuan Y. Li, C. Y. Hsieh

Realizing that aluminum will have a great role to play in the coming industrialization of China, Chinese geologists have long been looking about for some aluminum deposits. The possible sources appear to be alunite, the alumina-rich shales, and the bauxite deposits. The locations of deposits are shown in Fig. I. Alunite Our attention was first directed to the alunite deposits along the southeastern coast of China. Table I summarizes the reserves now believed to exist in that region. Other alunite deposits have been found in Kiangpei, Szechuan province; Charming. Liuyang and Hsanshan, Hunnan province Tsingchow and Chowyuan, Shantung province. No reserve figures are available. High-alumina Shale Shale high enough in aluminum to serve as a source of that metal has been found in northeastern China(Tab1e 2). In Manchuria, the Manchuria Light Metals Co., at Antung and Fushun, operating under Japanese control, has been the only active producer of aluminum. It is not known, however, whether the company uses local raw materials or imports ore from elsewhere.* Shantung Bauxite Bauxite was first recognized in China at Paoshan, Shantung province. Although the reserve is reported to be large (estimated at 271 million tons), the high content of insoluble residue (SiO2) and mineral composition (diaspore) are dis-

Jan 1, 1948

By Chingyuan Y. Li, C. Y. Hsieh

Realizing that aluminum will have a great role to play in the coming industrialization of China, Chinese geologists have long been looking about for some aluminum deposits. The possible sources appear to be alunite, the alumina-rich shales, and the bauxite deposits. The locations of deposits are shown in Fig. I. Alunite Our attention was first directed to the alunite deposits along the southeastern coast of China. Table I summarizes the reserves now believed to exist in that region. Other alunite deposits have been found in Kiangpei, Szechuan province; Charming. Liuyang and Hsanshan, Hunnan province Tsingchow and Chowyuan, Shantung province. No reserve figures are available. High-alumina Shale Shale high enough in aluminum to serve as a source of that metal has been found in northeastern China(Tab1e 2). In Manchuria, the Manchuria Light Metals Co., at Antung and Fushun, operating under Japanese control, has been the only active producer of aluminum. It is not known, however, whether the company uses local raw materials or imports ore from elsewhere.* Shantung Bauxite Bauxite was first recognized in China at Paoshan, Shantung province. Although the reserve is reported to be large (estimated at 271 million tons), the high content of insoluble residue (SiO2) and mineral composition (diaspore) are dis-

Jan 1, 1948

By R. P. Aikman, F. G. Miller, J. M. Podgursky

As part of a larger study of the mechanism of froth flotation of coal, the rates at which coal particles of various size and specific gravity react to froth flotation were investigated. Results of this study show that in flotation: I) recovery rate increases, but selectivity decreases with a decrease in particle size down to 100 mesh, and 2) recovery rate is constant for all sizes between 100M and 325M. n response to the growing demand for low-sulfur coking coal for iron making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, i.e., + 28 mesh, at almost any desired specific gravity. However, in the case of fine coal, i.e., —28 mesh, neither of the two existing processes - froth flotation or hydrocycloning — in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this paper is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods. The paper includes: 1) A discussion of the value of a detailed wash-ability study as a method of assessing the problems associated with fine coal processing, 2) A general discussion of hydrocyclone principles, included to serve as a basis for understanding the mechanism of coal flotation, and 3) A detailed discussion of the mechanism of coal flotation, as well as the research leading to the optimum use of froth flotation in combination with other fine-coal cleaning methods to provide efficient fine-coal processing. Our study of the rates at which coal particles of various size and specific gravity react to flotation shows that in flotation: 1) recovery rate increases but selectivity decreases with a decrease in particle size down to 100 mesh, 2) recovery rate is constant for all sizes between 100 mesh and 325 mesh, and 3) the flotation process effectively rejects only those extremely fine particles which do not contain surface carbon. (Because of this feature, froth flotation is an excellent method for rejecting clays - the only extreme fines in - 325-mesh coal that are always carbon free.) Washability studies of flotation products are used to assess flotation efficiency. These studies show that: 1) the increase in percent sulfur in flotation products above the theoretical sulfur content as defined by the washability study is due almost entirely to flotation of fine high-specific-gravity particles that are part coal and part pyrite, and 2) in a given size range particle floatability decreases with an increase in particle specific gravity. Error curves are explained and are used to compare the mechanisms of coal flotation and hydrocycloning. These comparisons show that hydrocyclone performance is affected primarily by particle mass, i.e., particle specific gravity and size, whereas coal flotation performance is dependent on both the particle mass and the coal surface available for bubble attachment. Since the error curve is a basic tool for rating the efficiency of any coal processing system, it will be useful to quickly review the principles of error curve construction. RATING COAL-PROCESSING EFFICIENCY BY THE ERROR CURVE The organic component of coal is of lower specific gravity than its impurities, and the most effective principle for coal concentration is therefore separation on the basis of specific gravity. However, since there is no sharp dividing line between pure coal and pure ash components, specific gravity must be closely controlled if the product is to have acceptable quality at maximum yields. In turn, the basis for close control in any coal processing system is the reference standard provided by precise laboratory washability studies. In these studies, coal is carefully separated into a series of progressively higher specific gravity fractions to establish a relationship

Jan 1, 1968

By P. K. Koh, L. S. Birks, J. M. Siomkajlo

Direct identification in situ of x and a phase precipitates in stainless steel is possible with the electron probe microanalyzer. Although particles in the 1 p size range are too small to yield absolute percent composition, the relative % Crfi Mo ratio can be used to distinguish the two phases with better than 95 pct confidence. Wet chemical analysis of extracted residues gives Cr/Mo ratios in good agreement with electron probe results extrapolated to the 4 to 5 p size range. WHEN stainless steels are subjected to extended heating in the temperature region around 1600°F, precipitation of the brittle 0 or x phases may occur and impair the properties of the material. Identi-

Jan 1, 1961

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By R. W. Raymond

THE situation in 1872, from the standpoint of the prospector, the locator, the possessory claimant, and the patentee of mineral land under Federal statutes, cannot be understood without a knowledge of the situation prior to 1866, and between 1866 and 1872. The Situation before 1866 The western public domain acquired by the United States through treaties, as the result of conquest or purchase, was invaded after Marshall's re-discovery of gold in California, by an overwhelming multitude of prospectors and miners from all parts of the world. The mineral lands of the whole Pacific slope were practically unsurveyed. Congress, disgusted with the experiment of leasing mineral lands; which it had tried for 40 years, and abandoned in 1847, enacted no laws for the management of these public mineral lands, and the pioneers made their own laws governing mining titles. These local regulations applied at first to gulch-mining in the auriferous river-beds only; and they constituted a simple and practical system, adapted to the needs and means of primitive communities-significantly called "camps." They had the means of measuring distances, but not angles; they knew no -property except personal property in the form of pickaxes, pans, supplies, camp-equipage, horses or mules, and mining rights. The earliest codes which they developed expressed what might be called the law of the lariat. With the lariat they measured the distance assigned to each miner along the gold-bearing gulch-a double portion to the discoverer, and a single portion to his successors, in the order of their coming. With the lariat, they hung, after such due process of law as was available, the rascal who stole a horse, or a bag of gold-dust, or a; mining claim, or killed another man without giving him fair notice and a chance to defend himself. In these pioneer codes, adopted in mass-meetings and enforced by the same authority, two features concern us most:

Jan 4, 1914

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

Graham Macfarlane, Louisville, Ky. (communication to the Secretary*):—In the paper by S. Whinery under the above caption mention is made of the occurrence of Clinton iron-ore in Kentucky and Tennessee. I believe that this is really a ferruginous limestone in what the Tennessee Geological Survey calls the Fernvale formation. In Davidson and Sumner counties, Tennessee, this occurs at about the horizon stated by Mr. Whinery. The maximum thickness of the deposit is from 10 to 12 ft., but it averages between 6 and 8 ft., lying practically horizontal. The Red River Furnace Co., under my direction, opened a mine in the Fernvale " red rock" near Goodlettsville, Tenn., several years ago. When it was first found we assumed it to be Clinton ore, but the absence of the characteristic Clinton fossiliferous structure and other evidence satisfied us that it is really limestone saturated with iron oxide. I think the very low ratio of SiO2 and Al2o3 to iron content as compared with the usual ratio in the Clinton ore is also evidence in favor of its being the Fernvale. The Tennessee Geological Survey states that at outcrops where this ore has been leached it carries about 44 per cent. of iron; under cover, from 20 to 25 per cent. of iron and from 3 to 6 per cent. of silica, the remainder being chiefly calcium carbonate. Its phosphorus content is irregular and generally rather high for a foundry-iron mixture. Since it is more than self-fluxing, we have at times operated with a mixture of brown hematite and red ore with no limestone.

Jan 1, 1913

THE CHAIRMAN.-Thank you. Since the papers are rather closely related, I think rather than taking them one at a time we will entertain discussion on any of these problems at this time. W. A. REICH.*-We, of course, quite a while ago got the yellow light that Mr. Cole spoke of, and like everyone else immediately started to study silicon bronzes and brasses. We were interested in the silicon bronzes and brasses because we felt that in order to replace gun metal which makes up a large part of our use we needed something with an elastic limit at least equal to that of gun metal. That means at least 12,000 lb. per sq. in. This study was aimed only at tin conservation. Then we dropped the study of silicon bronzes because high purity copper which is needed in their manufacture became a scarce item. To make a long story short we have recommended to our designing engineers that they use 85-5-5-5 wherever possible because 85-5-5-5 we understand can be made entirely from scrap with little or no tin addition. 85-5-5-5 has a lower elastic limit than 88-8-4, so we felt that we would need another substitute material, a structural alloy with an elastic limit equal to that of 88-8-4, and we immediately turned to the manganese bronze type of alloy. The poor foundry properties of standard manganese bronzes were mentioned by Mr. Thieme and since we feel that high zinc content is largely responsible for this difficulty, our development is directed along the lines of uncovering a material with a lower zinc content and which gains its elastic strength from the addition of other alloying elements, such as, aluminum, manganese and iron. It must be possible to make this alloy entirely from scrap with no additions of scarce high purity material. I would appreciate an expression of opinion on how low we can go in zinc content with this type of alloy without seriously impairing the availability, and how high we can go in aluminum content without making use of aluminum restricted for that use. We assume that the maximum lead content must be placed at 1 ½ per cent to insure good availability and we feel that about I per cent of tin in the alloy would improve salt water corrosion resistance similar to the effect of tin in Admiralty Metal. Has anyone here had experience with the effect of tin and lead on the weldability of such an alloy? C. S. COLE.-What percentage of lead and tin? W. A. REICH.-About 1 per cent of lead and 1 per cent of tin. We are studying the weldability of the alloy but perhaps someone already has the answer. (Pause, no answer) The claim has been made that 1 per cent of lead can be added to certain silicon bronzes without impairing their properties. A silicon bronze with a low zinc content requires high purity copper in its manufacture but if say the 15 per cent zinc, 44 silicon balance copper alloy could be made, with a I per cent lead content, some quantity could be made from scrap. We do not know whether the aforementioned is

Jan 1, 1943

By Oscar Aguilar, Jin-ichi Nakamura, Kazuo Nakamura

Michiquillay deposit is porphyry copper type with over 500 million tons of 0.70% Cu ore. In order to reflect the true nature of the orebody as to shape and value distribution and to compensate for insufficient data in the outer perimeter and lower portion, "Triangular Interpolation Method" is used in the computation, wherein block grades are determined by "Plane Regression". The results thus obtained are compared with the data from additional investigation and are found to match well with each other. Aside of total Cu, assays of Fe, S, MoS2 and geological data such as alterations, rock types, faults, mineralogical compositions are also stored in the computer. By this system, their distribution and relation to alteration become clear and classification of ore into types affecting recovery become possible. The outputs of this system make clear the characteristics of the orebody and furnish valuable geological data on the orebody.

Jan 1, 1976

By Zhengbo Pan, Fujun Gou, Jifei Chen

This paper discusses the various alternatives that are technically feasible for "over-the-raise" continuous advancing in gently inclined coal seams and the computer-aided selection of the optimal mining option. Examples in Wangshiao Coal Mine and Chaohua Coal Mine are cited to illustrate the interval between raises, face length, single or double raise layout and single or double face layout.

Jan 1, 1983

The following is an incomplete list of members and guests who called at Institute headquarters during the period June 10, 1918 to July 10, 1918. F. C. Alsdorf, Tucson, Ariz. Emory M. Marshall, Camp Raritan, N. J. Juan F. Brandes, Santa Barbara, Cal. Jacques S. Negru, Camp Niagara, Ont. .H. Smith Clark, Kansas City, Mo. Arvid E. Nissen, High Bridge, N. J. J. S. Cunningham, Charleston, W. Va. Richard G. Place, So. Strafford, Vt. W. G. Eberhardt, Tucson, Ariz. Frank H. Probert, Berkeley, Cal. M. Eldredge, Bombay,. India. Martin A. Roudabush, Osterburg, Pa. A. D. R. Galloway, Accra, W. Africa;. P. H. Royster, Minneapolis, Minn. F. Hanst, Harrisburg, Pa. J. L. Schueler, Peoria, Ill. B. B. Hood, Chrome, N.. J. Henry B. Smith, New Britain, Conn. Paul S. King, Wilmington, Del. W. G. Sommer, Peoria, Ill. E. D. Kinney, Anaconda, Mont. A. L. Toenges, Roanoke, Va. E. W. Kohl, Jr., Philadelphia, Pa. G. D. B. Turner, Butte, Mont. James W. Love, Knoxville, Tenn. A. T. Ward, Bellefonte, Pa. Edwin A. Austin, formerly with the Yukon Gold Co., is superintendent of the Elkoro mine at Jarbidge, Nev. John W. Beard is now with the Cia Minera de Penoles, Ojuela, Dgo., Mexico, via Mapimi. R. S. Bonsib has accepted a position with the United States Emergency Fleet Corporation as District Safety Engineer, San Francisco, Cal. Albert Burch has been appointed by the Bureau of Mines to encourage the mining of chrome. F. B. Caldwell is working for the U. S. Bureau of Mines, under Albert Burch, in the investigation of chromite deposits. W. A. Carlyle has taken over the duties (in addition to his own) formerly assigned to E. P. Mathewson with the British America Nickel Corporation, at Sudbury, Canada. R. M. Catlin received the honorary degree of Doctor of Science at the recent commencement of Rutgers College, New Brunswick, N. J. S. K. Dahl is giving up his position as mill superintendent with the Messina Mines, which have been suspended, and is returning to this country. Algernon Del Mar has become manager of the Techatticup mines, El Dorado Canyon, Nev. Robert Dye has succeeded D. L. Forbes as manager of the Teck-Hughes at Kirkland Lake, Ont., Canada. J. O. Elton, superintendent of the Anaconda company's electrolytic zinc plant at Great Falls, Mont., is doing special work with the U. S. Bureau of Mines. R. B. Caples takes charge of the plant in his absence. George H. Gibbs has resigned his position as engineer at Messrs. T. & 1. Bradley & Sons, Ltd., Darlaston blast furnaces, Darlaston, and is now located at "Belmont." Litchfield Road, Rushall, Walsall, England. William D. Gordon, for the past 7 years manager of The Mine & Smelter Supply Co. at El Paso, has been elected president of Camphuis, Rives & Gordon,. Inc., and has opened American headquarters for the company at 81 New Street, New York, N. Y. E. Harms, for the past 16 years inn charge of metallurgical operations of the Torreon, Mexico; lead and copper smelter, has resigned and is now located at El Paso, Tex.

Jan 8, 1918

By William P. Blake

The late Dr. Ebenezer Emmons of Albany, one of the geologists of the Survey of New York and the author of The Taconic System, brought to notice as early as 1838" a peculiar concretionary and lamellar form of phosphate of lime, to which he gave the name Eupyrchroite, from the Greek words for fire and color, with the pefix

Jan 1, 1893

By C. W. Phillips, D. N. Frey

A commercial Ti-Fe-Cr alloy, Ti-150, exhibits a martensitic transformation on cooling and two nucleation and growth reactions, one above and one below the Mg-Mf region, on isothermal holding below the single-phase ß temperature range. The reactions were followed by metallographic, X-ray diffraction, and microhardness methods. THE rapidly expanding engineering application of titanium and its alloys makes increasingly urgent an adequate knowledge of the effect of heat treatment on this material. The work herein reported is an attempt to determine certain aspects of the behavior of a commercially available alloy, Ti-150, during heat treatment. The alloy, with a nominal composition of 2.7 pct Cr, 1.3 pct Fe, 0.25 pct 0, 0.02 pct N, and 0.02 pct C, was received in the as-rolled condition as a 3/4 in. round. Slugs 0.11 to 0.12 in. thick were cut under a coolant using a silicon carbide wheel. Preliminary work established that the alloy consists of two phases, a (hexagonal close-packed) and /3 (body-centered cubic), at temperatures below 1750" to 1775"F, and of only /3 phase at higher temperatures. The slugs were heated for 1 hr in air at 1800°F to form a single-phase /3 matrix, then transferred to molten tin (1250° to 1650°F) or lead (1150°F and below) for isothermal holding. Holding temperatures ranged from 700° to 1650°F, times from 0.001 to 23 hr. The treated slugs were then sectioned, one part for metallographic examination and diamond pyramid hardness, the other, after deep etching to remove the high oxygen surface,' for comparative lattice parameter determination and X-ray phase identification. Hardness measurements were taken on the lightly etched surfaces of the metallographic specimens; a 1000 g load on a 136° diamond pyramid was used. Five impressions on each sample were made and the average of the hardness calculated. The use of microhardness measurements to follow the course of an isothermal transformation reaction is undesirable because of the possibility of wide differences in microconstituent hardness.' They were used in this case, however, because of the small amount of material available. At the higher transformation temperatures, where the above-mentioned objection was apparent, the readings were proportioned to correspond to the estimated ratio of transformed and untransformed constituents present. At lower temperatures, resulting in much finer microconstituents, the microhardness measurements were more uniform. The standard deviation of the mean of five impressions calculated from these latter values was 4.2 DPH. Employing 2a limits (probability 0.95) the experimental error of the hardness measurements averages was 8.4 DPH. The etchant used was composed of one part glyc-erol and one part 48 pct hydrofluoric acid." Of a number of etches tried, this one appeared most satisfactory. All micrographs were taken at 500X magnification and with oblique lighting to permit easier identification of the acicular structure resulting from rapid cooling. No advantage was gained by using polarized light for metallographic examination. Phase identification and lattice parameter measurements were made with a North American Philips high angle spectrometer in conjunction with a recording potentiometer. Considerable difficulty was encountered with some of the lattice parameter measurements because of the extreme broadness of the few diffraction lines obtained from samples consisting mainly of strained, untempered, quenched structures.

Jan 1, 1953

By Oliver Bowles

Dimension stone is a term applied to stone sold in blocks or slabs of specified shapes and usually of specified sizes, contrasted with crushed, broken and pulverized stone covered in another chapter. Dimension stone includes cut stone, rough building stone, ashlar,* rubble, monumental stone, paving blocks, curbing, flagging, and many types of ornaments and novelties carved from stone. Riprap-large, irregular blocks used for shore protection-is classed with crushed and broken stone. Composition, Varieties, and Properties Dimension stones are of many kinds. The principal varieties are granites, trap rock (diabase, basalt, and gabbro), sandstone, limestone, and marble. Slate is covered in a separate chapter. Granite is a visibly granular crystalline rock consisting essentially of feldspar, quartz, and mica or hornblende. The basaltic rocks are darker in color than the granites. They contain little or no quartz and consist largely of plagioclase feldspar, augite, pyroxene, and hornblende. They are classed commercially as black granites. Limestone consists essentially of calcium carbonate. Dolomites and magnesian limestones used as dimension stone are classed with the high-calcium limestones. Marble is a crystalline form of limestone, but in the trade, any carbonate rock which will take a polish is called a marble. Many limestones which are fossiliferous but which will take a polish are sold as a decorative stone for lobbies of hotels and office buildings. Sandstone consists essentially of silica in the form of sand grains cemented into a coherent mass. Although rock occurrences are numerous and widespread, the exacting requirements of use condemn all but a small fraction of them for commercial use as dimension stone. No deposit that has closely spaced joints or planes of weakness can be used because sound blocks of moderate to large size are demanded. Uniform texture and grain size, constant and attractive colors or color pattern, and freedom from impurities that may cause stains or deterioration usually are demanded. Hardness is a variable property. Granites and diabases are as hard as or harder than steel, while limestones and marbles may be scratched with a knife. The hardness of sandstone depends upon the degree of cohesion of the grains. Workability depends to a considerable extent on hardness, but the degree of hardness has little influence on use except where stones are subjected to abrasion as on steps or floors. "Texture" as applied to stone relates to the arrangement, uniformity, and size of the constituent grains. Stones are of many colors and thus can satisfy a variety of tastes. For monumental stone, a marked contrast between polished and tooled surfaces is preferred in order that inscriptions may be read easily. Strength requirements usually may be disregarded because any sound structural stone suitable in other respects is almost invariably many times as strong as would be required for any ordinary use. The pressure on the base course of the Washington Monument, Washington, D. C., is less than 700 psi, and highgrade granites, limestones, sandstones, and marbles will sustain a crushing load of 10,000 to 25,000 psi. A structure made of stone with a crushing strength of 15,000 psi would have to be nearly 21h miles high before crushing of the lower courses would occur. However, stone disintegrates more readily under severe

Jan 1, 1960

By A. M. Rowe

A considerable quantity of experimental hydrocarbon K-factor data has been correlated as a function of component identity, temperature, pressure and convergence pressure. To utilize these correlations effectively, convergence pressure must be determined accurately, particularly for volatile mixtures near their critical states. This paper presents phase diagrams that illustrate physically the meaning of convergence pressure. A new method, referred to hereafter as the "critical composition method", will be outlined for calculating convergence pressure. An example calculation has been included to illustrate how to use this new technique. INTRODUCTION The principle of hydrocarbon phase composition calculations as applied to such diverse problems as optimizing separator performance or predicting fluid compositions at various stages of reservoir depletion is the same. Usually, temperature, pressure and the numbers of moles of the various components of the fluid contained in a given volume are known. Questions answered by the phase calculation are what fraction of the total mass of fluid exists in each of the equilibrium phases, and what are the mole fractions of the various components in the two phases? To answer these questions the Natural Gasoline Supplymen's Assoc. (NGSMA) has correlated a considerable quantity of K-factor data as a function of temperature, pressure, component identity and convergence pressure.l To use these correlations to obtain the best answers possible, one must be able to calculate the convergence pressure. This is particularly true for over-all fluid compositions in the neighborhood of the critical state. STATEMENT OF THEORY Use of convergence pressure as a correlating parameter is based on a postulate similar to the law of corresponding states used in correlating PVT data of hydrocarbon gases. This postulate, which proposes convergence pressure as a correlating parameter, has been stated as follows: "The equilibrium vaporization constant for one component in a complex system is the same as the equilibrium constant at the same temperature and pressure for the same number or kind of components, providing only that the convergence pressures of the two systems are exactly the same at the same temperature and that the components are of the same homologous series".2 This law, as with all laws of physics, cannot be proven theoretically. It can only be justified by experimental data supporting its premises. Arguments have been made that this law violates Gibb's phase rule. For example, consider a four-component system. By Gibb's phase rule, which is thermodynamically rigorous, f = c — P + 2 =4, for a four-component, two-phase system. Thus, four independent intensive variables must be specified to establish completely all the intensive variables of the equilibrium phases. On the other hand, according to convergence pressure theory, only three variables need be specified for any mixture containing four different components. These variables are temperature, pressure and convergence pressure. Thus, the two laws appear to be in conflict. However, the convergence pressure postulate is more restrictive than Gibb's phase rule. It applies only to mixtures of the same homologous series. Hence, these two concepts are not in disagreement. PHASE DIAGRAMS DESCRIBING CONVERGENCE PRESSURE This paper presents phase diagrams grading from the simple two-component system to the more complex four-component system to illustrate convergence pressure. A less abstract definition of convergence pressure will be stated that is

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc.* When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society but the name has now been changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering societies Building and to various funds placed in its charge and is managed by a Board of Trustees of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which own equal and undivided interests in the property. The land and building cost two million dollars. The interest of each of the Founders societies, aside from especial trust funds, is now valued at $493,352. The A. I. M. E. trustees are Arthur S. Dwight, J. V. N. Dorr and H. A. Guess. George D. Barron will succeed Mr. Guess as trustee at the end of this year. The President of the Board is Francis Lee Stuart and the Secretary, Alfred D. Flinn. The Engineering Foundation The Engnieering Foundation was established in 1814 as a result of a gift of $200,000 made by Ambrose Swasey. It is intended not only "for the Furtherance of research" along broad lines but also "for the advancement of" a wide variety of other activities of benefit to engineering as need arises. The endowment fund, which now amounts to $630,000, is administered by the United Engineering Trustees, Inc. Through The Engineering Foundation board, on which the Institute is now represented by J. V. N. Dorr, John M. Callow and Galen H. Clevenger, the income of the endowment, approximately $28,000 a year, and funds contributed for special projects are appropriated for the purposes intended. H. C. Bellinger will succeed Mr. Callow on the board at the end of this year. Alfred D. Flinn is Secretary- and Director. Researches of wide interest in many lines have been aided by Engineering Foundation. . A grant from it to the Mining Methods Committee assisted in the preparation of Volume 72 of the Transactions. For several years the Foundation has aided in support of the study of Blast-furnacc Slags by R. 8. McCaffery at the University of Wisconsin, sponsored by the Institute. The Foundation has raised over $230,000 to support the Alloys of Iron Research endorsed by the Institute and George B. Water-house is serving as Chairman and Director of the Iron Alloys Committee which has been brought together to direct this work. The Foundation has also on recommendation of the Institute made a grant in aid of the studies of Mining and Strata being conducted at Columbia University by P. B. Bucky, which promise information of great usefulness relative to mine subsidence and support of ground. John Fritz Medal Board of Award The medal was established in 1902 and lias since, been awarded not oftener than annually by a hoard of sixteen members, four representatives each from the American Societies of Civil, Mining and Metallurgical, Mechanical, and Electrical Engineers.

Jan 1, 1930

By Mark E. Emerson

INTRODUCTION A long time has passed since geologists encountered encouraging mineralization in their regional exploration program for base metals deposits. Detailed drilling during the following two field seasons served to delineate the configuration of the deposit. Various statistical techniques were employed to provide confidence levels regarding the extent of the reserves and to categorize them according to whether proved, indicated or inferred. At this juncture, it appears that the company has an orebody. Time elapsed? - three years; money spent? - $2.5 million. Much remains to be done before the orebody becomes a mine. The company urgently needs to develop new orebodies to replace its existing mines which are being depleted. It therefore has expended sizable amounts in exploration, the life blood of the company. A staff of specialists is maintained to evaluate new projects and to conduct feasibility studies. The scale of new mining projects today is beyond the resources of most mining companies. Bank financing, therefore, is often vital if the company is to survive. The following scenario describes how a company goes about evaluating mine projects and what is needed to meet lender's criteria in securing the needed financing. MINE PLANNING Now that the company engineers have taken over the project, their concern is no longer with finding ore but in developing it. An exploration shaft has been put down and a tunnel driven into the orebody to verify, on a large scale, what has been seen so far only in pencil- like drill cores. A large tonnage bulk sample is mined and shipped off to an independent metallurgical process laboratory for beneficiation testing. The budget is expended to cover engineering studies. Preliminary capical and operating costs are developed in- house and profitability studies are made based or1 assumptions concerning the markets for the main product and the indicated gold, silver, and other by-products. Time elapsed? - four years; cost to date? - $3.5-$4.5 million. The staff prepares its own pre-feasibility study. After review, the Executive Committee authorizes management to proceed with full-scale studies. The task is to make preliminary designs and to develop definitive capital and operating cost estimates. Specialized consultants will be engaged to study slope stability for the open pit and rock strength if underground recovery proves more feasible. If it is near the sea, an oceanographic report might be commissioned to see if the tailings can be disposed of off shore. Environmental impact studies are commissioned from a firm familiar with government requirements and regulations in this important area. The company subscribes for an expensive multi-client study of the supply- demand-price outlook for the product to support its own long-range price forecast. Now all the numbers are available to make a definitive appraisal of the value of the project. Cash flow analyses and sensitivity studies follow. Reams of computer printouts are generated. Time elapsed: five years. Amount spent? - up to $9 million, depending on the size, complexity and attractiveness of the project. Marginal projects always take longer. Finally, an engineering and construction (E&C) company is given the task of integrating and compiling all the data into a feasibility study. The results of dozens of reports, memoranda, computer printouts, and charts are boiled down to one final summary report of a few hundred pages together with conclusions and recommendations. After thoughtful review at a board meeting, the directors authorize management to proceed with detailed engineering work - provided that

Jan 1, 1985

By Gilbert L. Eggert

The effects of reactor irradiation on age hardening in a Cu-2 wt pct Be alloy have been investigated in two neutron-energy ranges. During some of the irradiations, specimens were exposed to high-energy fission neutrons which passed through a boron-10 shield; during other bombardments, the boron-10 was omitted and specimens were irradiated in a reactor thermal column, or the fuel configuration was modified to increase the thermal-neutron flux at a location in the core. Differences in length, X-ray diffraction angle, and hardness indicated that low-energy neutron irradiation made a small contribution to changes in the measured properties. The influence of defects generated by knock-om with less than the Brinkman critical energy or by prompt (n,y) recoil is suggested as the cause of this effect. EXPERIMENTS designed to test the effects of reactor irradiation on the properties of age-hardening alloys have to the present time employed fluxes un-differentiated according to neutron energy. Billing-ton and Siegell in 1950 were the first to perform such an experiment and to compare the results with those obtained by thermal aging. These authors concluded that precipitation in a Cu-2 wt pct Be alloy was not enhanced by the radiation. However, 4 years later, Murray and Taylor,2 working with specimens of the same Cu-2 wt pct Be alloy, reported that an increase in density, hardness, and resistivity which followed reactor irradiation resembled changes associated with thermal aging at about 100°C. (It should be noted that these authors reported that higher aging temperatures caused a decrease in resistivity.) cupp3 reported hardness results similar to those of Murray and Taylor. Koppenaal4 showed that irradiation-enhanced precipitation and irradiation defect hardening were not simply additive but that they acted separately in an irradiated alloy. Kernohan et a1.,5 working with Ni-Be, offered evidence that beryllium was removed from solid solution by reactor irradiation and suggested that the mechanism was one of increased diffusion through the use of vacancies in the structure. piercy6 also found that more precipitate particles were formed by fission-neutron irradiation of a Cu-Co alloy which contained a small amount of particles before irradiation. He proposed that the additional particles were caused by an appreciable amount of diffusion during the final cooling of displacement spikes. The retrogression of extant precipitate particles found by Murray and Taylor2 and Boltax7 as well as piercy6 indicated that nuclei were dissolved within a high-energy spike region and, upon resolidification of the perturbed volume, new nuclei precipitate and grow by enhanced diffusion. Bleiberg et al.' and Konobeevski et al.' explained phase changes obtained by irradiating fissionable alloys in terms of retrogression and re-precipitation in regions of high-energy spikes. Parsons and Balluffi10 used electron microscopy to verify that crystallization did indeed occur in displacement spikes which were formed in amorphous germanium by fast-neutron irradiation. The concept that low-energy neutron irradiation might cause structure-sensitive property changes in semiconductors by atomic recoil associated with the (n, y) reaction was first proposed by Schweinler" and walker." This thesis was tested by Cleland and crawford" and found to be valid. Coltman et al.14 exposed a variety of pure metals to thermal-neutron irradiation at cryogenic temperatures and attributed the resulting resistivity changes to the action of defects created by (n, y) recoil. The present work was undertaken to extend the concepts of Schweinler," walker," and Coltman et al.I4 to the case of an age-hardening alloy and to determine whether or not the action of defects produced by thermal-neutron irradiation would en-hance age hardening. EXPERIMENTAL PROCEDURE Omeea West Reactor Irradiations.* Thermal-

Jan 1, 1965

By W. J. Helfrich, C. L. Sollenberger

Many present direct reduction processes utilize iron ore concentrates for the production of sponge iron and the sponge iron is usually preferred as an agglomerate. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. The present paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. The kinetics of iron oxide reduction have been I studied by numerous investigators1-4 and a rate equation for the hydrogen reduction of hematite and magnetite has been proposed. Mc Kewan' obtained kinetic data for the reduction of hematite spheres sintered at 13'70°C (2498'F'). The kinetics of magnetite reduction was studied by Quets. He compacted the oxide at a pressure of 1 ton per sq cm and sintered the specimens to densities of 95 to 96 pct of theoretical. These studies demonstrated that the reduction of iron oxide is a topochemical process and that the rate of reduction is proportional to the receding surface area of remaining iron oxide. Thus, the measurement of the kinetics of iron oxide reduction depends upon the development of a measurable and well defined interface between metal and reacting oxide. It is evident that the reduction rate will be constant only when the rate of formation of the reaction product layer is constant. It was recognized by Joseph' and Edstrom' that the physical character of the oxide will determine the configuration of the interface between oxide and metal. The reduction of oxides which exhibit few pores or no interconnected pores should proceed by topochemical processes. However, if a massive or dense crystalline ore cracks during the reduction of the oxide, thus allowing the reduction to Proceed away from a well defined oxide/metal interface, then the observed reduction rate will vary or change during reduction. From a process standpoint, it would be difficult to apply absolute reduction rates determined for crystalline or nonporous iron oxide to the direct reduction of a porous pellet of iron ore concentrate. Most present direct reduction processes are attempts to utilize iron ore concentraates in the production of sponge iron. The sponge iron is usually preferred in an agglomerated form for subsequent melting practices. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. One process for preparing such a product has already been de-scribed. This paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. ORE CONCENTRATES STUDIED A magnetite concentrate from Reserve Mining Co. and a hematite concentrate from U.S. Steel Corp. were used in preparing pellets for these experiments. A head analysis of these concentrates is given in Table I. To compare the reduction rates of pelletized concentrates, it was necessary that each pellet contain equal amounts of oxygen which could be removed by reduction, regardless of the oxidation state, i.e., Fez% or Fe304. Also, because of the difficulty in preparing spherical pellets of uniform size, weight, density, and porosity for experimental purposes, pellets of a cylindrical shape were formed in a press.

Jan 1, 1961