Search Documents

By J. Wade Watkins, E. S. Mardock

The accurate evaluation of reservoir-performance characteristics in the secondary recovery of petroleum by water flooding requires use of a water tracer that may be injected into water-input wells and detected at oil-production wells to supplement data obtained from core analyses, wellhead tests, and subsurface measurements. Radioactive iodine has been used successfully as a water tracer in field tests to determine: (I) relative rates and patterns of flow of injected water between water-input and oil-production wells and (2) zones of excessive water entry into oil-production wells. Laboratory evaluations of potential water tracers, previous tracer studies, the value of using a radioactive tracer, general field procedures, and the use of surface and subsurface instruments for the detection of the emitted gamma radiation, are summarized. Data from the field tests are presented graphically and discussed in detail. It is concluded that the radioactive-tracer method, using radioactive iodine, may be used successfully to measure either the relative rates and patterns of flow or zones of excessive water entry into wells under conditions of comparatively rapid transit time between wells. INTRODUCTION Extensive use is made of data obtained from core analyses, wellhead tests, fluid characteristics, and subsurface measurements in evaluating the sweep efficiency of water injected into oil sands for the recovery of oil. Theoretical flow rates and patterns may be calculated from those data using radial-flow formulas, if it is assumed that the physical conditions in the productive formation are homogeneous. Unfortunately, homogeneous conditions rarely, if ever, exist in oil-productive formations. The use of a tracer that may be injected into an oil sand and detected quantitatively, or even qualitatively, at offsetting oil-production wells provides basic data that may be used in determining more accurately the subsurface rates and patterns of flow of injected water between wells than is possible by theoretical calculations based on assumed conditions. Consideration of the data obtained by using a water tracer assists in the application of remedial measures to water-input wells, such as plugging of channels, or selective plugging of highly permeable zones, thereby effecting a more uniform flood and a greater ultimate oil recovery. A water tracer should have the following characteristics: (1) low adsorption on solid reservoir material; (2) high solubility in water; (3) low or negligible solubility in crude petroleum; (4) a wide range of solubility of compounds that may be formed by chemical reactions with ions present in reservoir rocks or waters; (5) high detectability in low concentrations by portable apparatus; and (6) general availability at low cost. Additional desirable characteristics are that the tracer should be nonhazardous in nature under normal working conditions and quantitatively detectable in the well bore, as well as at the surface. Review of Previous Tracer Studies The need for a water tracer has been recognized for many years. As far back as 1906, Dole1 described the use of fluorescein in flow-rate studies made in France in 1901. In 1921, Ambrose" discussed in detail the use of organic and inorganic dyes, chlorides, nitrates, and other anions, lithium salts, and the Slichter electrical

Jan 1, 1955

By B. M. Larsen, T. E. Brower

For some years we have been carrying on a rather comprehensive investigation of the occurrence of oxygen in liquid open-hearth steel. This investigation was interrupted by the war emergency and is therefore incomplete, with many questions still answered only partially, if at all; yet it seemed worth while to present a report of progress on this difficult field of research, if for no other reason than to promote discussion and further investigation of this important problem. The significance of such studies depends in large measure upon the accuracy of measurements of oxygen content in liquid steel while it is still in the furnace or as it flows into the ladle, or thence into the mold and there is, as we shall show, good reason for believing that the main source of uncertainty is in the sampling, not in the analytical method as such. The difficulty arises from the fact that any method of sampling is of itself apt to alter the amount of oxygen in solution in the liquid steel, because this oxygen is in a readily reactive condition. On the one hand, being usually present at a concentration appreciably in excess of that corresponding to equilibrium with the carbon then present, it may decrease rapidly in percentage by reaction with carbon and evolution of CO, especially if the liquid metal is in any way shaken or brought in contact with a cooler solid surface. On the other hand, it may increase rapidly by ab- sorption of oxygen from a slag, a furnace atmosphere, or from air. These circumstances, which are inherent in the problem, as well as our conclusion that, despite the considerable amount of careful work already done, there is still no method of sampling liquid steel acceptable as an unquestioned standard, ed us to undertake systematic comparisons of oxygen content of large numbers of samples taken: (I) by a single method at different positions and levels in the bath; (2) at the same place by different sampling methods; and (3) from bath, tapping stream and pouring stream. The different sampling methods yield somewhat different values and there is as yet no way to tell with certainty which is the most accurate. But the general reproducibility and consistency of the results give us some confidence in certain inferences we draw from them: namely, that the "spoon" method of sampling, properly carried out, gives somewhat more consistent results than the "bomb" method, as it has usually been practiced; that, in the bomb method, an aluminum cap is preferable to a steel cap; that the oxygen content of liquid steel in a finished heat is substantially the same all over the bath at the same level, and tends to decrease at lower levels further from the slag interface; also that it tends to decrease, and to decrease erratically, from furnace bath to tapping stream entering the ladle. Accordingly it seemed desirable to report these observations in detail as a first step, so that the reader may judge their significance as a contribution towards solution of the main problem, which is to find a means of pre-2

Jan 1, 1945

By John C. Cook

Long-wave short-pulse radar has been shown capable of exploring to distances of several hundred feet through massive, dry rock salt. Exploration distances of 30 to 60 ft through bituminous coal and massive limestone, respectively, have also been demonstrated with low-power experimental radar equipment in underground mines. Working ranges up to 250 ft in limestone and coal are considered feasible. Radar reflections should be produced by all large electrically contrasting objects such as fault gouge masses, wet shattered ground, metallic mineralization, adjacent mine workings (dry or flooded), and abandoned drill holes. It is believed that radar can locate such obstacles in advance of underground mining through all massive rocks of low free-water content, including many igneous and metamorphic rocks. Three years of studies and experiments in radar exploration through rocks are reported.

Jan 1, 1974

By Henry Mulryan

DIATOMS are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skeletons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of varying thicknesses. DIATOMITES Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition. DIATOMS More than 8000 species of diatoms have been named and classified. Some are definitely classified as to their habitat; some are so well recognized as to their living conditions that they can be stated to be diagnostic types, and when encountered in a deposit determine the origin of the deposit. Some of the commoner types of diatoms found in the fresh-water diatomites on the Pacific Coast are: [Cymbella lanceolata Agardh Fragilaria virescens Ralfs Encyonema prostratum Ralf s Diatoma vulgare Bory Surirella biseriata Brebison Eunotia major Ehrenberg Amphipleura pellucida Kutaing Stictodiscus niagarae Ehrenberg Gomphonema geminatum Lynberg Melosira granulata Ehrenberg]

Jan 1, 1939

By Paul Weir

Bleaching clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the southeastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.l Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). The fuller's earth type of clay is characterized by a lack of plasticity, relatively adsorbent, foliated structure, and does not swell to form a

Jan 1, 1942

By Paul Weir

Bleaching clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the southeastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.l Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). The fuller's earth type of clay is characterized by a lack of plasticity, relatively adsorbent, foliated structure, and does not swell to form a

Jan 1, 1942

By Thomas D. West

The fact that iron expands when heated, until fusion takes place, and that molten iron is consequently less dense than solid iron of the same grade, is now universally admitted. It was proved by the extensive experiments of Mr. Thomas Wrightson, reported in the Jownal of the Iron and Steel Institute (1890, No. 1, p. 72, and 1891, No. 1, pp. 75, log), and, in a manner, is illustrated in heavy founding by the shrinkage 'of the molten metal, which must be " fed " in order to obtain solid castings. This decrease in volume requiring " feeding" while the metal is still liquid I call " shrinkage," applying the term " contraction" to the decrease in volume which takes place after solidification, while the iron is cooling to atmospheric temperature. The light-work founder, not having the opportunity to make heavy castings, in which shrinkage can be observed, is apt to confound the two; but they are in fact distinct, and are separated by an act of expanion, which takes place at the moment of solidification. The fact of this expansion was first practically demonstrated by Mr. John R. Whitney, of Philadelphia, Pa., whose experiments are recorded in the National Car and Locomotive Builder of May, 1889. Experiments recently made by the writer indicate that there is a constant relation between this expansion and the preceding shrinkage and forcibly demonstrate the necessity of " feeding " a casting to make its interior solid. This is a matter with which all makers and users of castings have experienced difficulty. The founder being heretofore unable to define correctly the principles involving the urgent necessity of " feeding " has failed to impress the moulder with its importance in making sound castings.

Jan 1, 1897

By I. A. Goddard

INTRODUCTION This paper deals with the development of the sublevel open stoping (SLOS) method in lead orebodies at the Isa Mine of Mount Isa Mines Limited, during the last ten years. Open stoping in different forms has been used at the Isa Mine for many years. Prior to the period under review, stopes were small, pillars were not always recovered, and scrapers extracted the ore. By the end of the sixties, the use of load-haul-dump units was becoming more widespread. Wagner ST5's were the mucking units for the lead cut and fill stopes. Some of the open stopes in 5 orebody above 13 level had 100 kW slushers, but the more southerly stopes were the sites for the introduction of diesel front-end loaders for extraction. In the early seventies, new methods were used in the block of six stopes in 2 and 5 orebodies between 8 level and 13 level and a trial stoping project was undertaken in 7 orebody between 11 level and 13 level to determine possible stope dimensions for the extraction of the Racecourse orebodies below 13 level. By the mid-19701s, stoping was well underway in 5, 7 and 8 orebodies between 13 level and 15 level, using the 'triplet' system, incorporating cemented hydraulic fill to allow greater pillar recovery. As the eighties were entered, development of the Racecourse orebodies below 15 level commenced, as did preparations for 1 orebody in the upper levels of the north end of the mine. In both cases, the pillar recovery method has been changed to reduce the amount of cemented fill required for pillar recovery. GEOLOGY Most of the lead orebodies at Isa Mine lie chiefly to the north of the central shaft complex. They are bedded sulphide deposits in a host rock called Urquhart Shale, which dips at roughly 650 to the west. The main minerals are galena and sphalerite, with the silver mineral, freibergite, being contained in the galena. To the hangingwall of the sequence are the Black Star orebodies (1, 2 and 5) which are relatively wide, pyritic and with low to above average grade lead. The Racecourse orebodies (6 to 16) lie to the footwall, and have a large variation in width, low to high grade lead, and gradation in the lead to zinc ratio from north to south. Stope outlines are often determined by economic or engineering considerations rather than geological. The published extraction reserves are 56 million tonnes of primary ore, containing 150 grams of silver per tonne, 6.4% lead and 6.5% zinc. Traditionally, it has been regarded as lead ore, although the dominant revenue earner varies from time to time. In the Black Star orebodies, the ore and hangingwalls are more competent and open stoping has long been used. The major Racecourse orebodies which have been open stoped are 7 and 8 orebodies. This has been where the orebodies are wider (to the south) and where hangingwall conditions allow. This latter aspect has been greatly influenced by the presence of 'silica dolomite1. This tough, relatively homogeneous, non-bedded rock is, in fact, the host rock for the copper mineralisation at Mount Isa, and provides a competent hangingwall for some of the lead stopes. While the shale's bedding and jointing has a major influence on the ground conditions, there is a major fault system which causes local problems. The principal virgin stress direction is perpendicular to the bedding, but the local stress situation is complicated because of shielding by filled stopes in the hangingwall copper orebodies and because of the interaction between orebodies being extracted to the footwall. Most development on strike is mined with a 'shanty-back’, with the back being as close to normal to the bedding as possible. This is near parallel to most jointing and the principal stress direction. Figure 1 is a plan view of 14 level north, which provides a representative horizontal section through the orebodies. A typical cross section is shown in Figure 2. The narrow, parallel footwall orebodies can be seen to differ from the wider hangingwall orebodies.

Jan 1, 1981

By H. I. Kaplan, C. Laird

Pulsating contpresslon experiments have been carried out on coppev single crystals in order to test the adequacy of mechanisms which have been suggested for stage I cvack grouth when tension-compression loading is the mode of- applying stress. Although dejorrrzation continues slowly for many millions 01 cycles under Pulsating compression stresses both within slip bands formed in the first cycle and by the creation of new bands, the morphology of these bands is not typical of fatigue slip bands in general and neither initiation of cracks nor propagation of artificially induced cracks was observed. It is therefore concluded that 1) initiation and growth of cvacks in fatigue is a consequence of repeatedly reviersed, microplastic deformation rather than intermittent, unidirectional deforma-tion, 2) gvowth of- cracks in polycrystalline specimens FAILURE of a plain specimen subjected to cyclic tension-compression stresses is known to take place by two stages of cracking.1,2 The first stage is characterized by propagation along slip planes roughly at 45 deg to the stress axis, in the outermost layers of the specimen, and at a rate of the order of angstroms per cycle. The average macro orientation of a stage I crack is normally at right angles to the stress axis,3 however, except in a few cases, e.g., single crystals in suitable orientation, when both the micro and macro directions of propagation are at 45 deg to the axis. After a stage I crack has penetrated to such a depth that the stress on the remaining section of metal is significantly increased, stage II crack propagation succeeds stage I, at right angles to the stress axis both micro and macroscopically. Direct evidence of the processes occurring during a subjected to pulsating compression stresses is caused by the setting-up of local tensile stresses due to interactions between grains, and 3) both unslipping mechanisms and operation of the "plastic blunting process " within a single slip band are adequate descriptions 01- stage I growth, being fundamentally similar. The slip mode of a material, however, is considered to control whether unslipping or the plastic blunting process takes place. Thus materials of planar slip mode fauor unslipping while those hacing a wavy mode, and capable of cross slip, can fail in stage I by the plastic blunting process. Similarly, and perhaps more importantly, reversed torsion and tension-compression modes of applying stress may be expected to cause the unslipping mechanism and the plastic blunting process, respectively. single stress cycle4,5 shows that stage II crack propagation takes place by a repetitive plastic rounding and closing of the crack tip. This mechanism has come to be called the "plastic blunting process".6 On the other hand, the extreme smallness of the phenomena occurring in stage I growth prevents elucidation of its mechanism by direct observation. Many suggestions have been proposed for this mechanism,'"-" most of them involving some kind of random or systematic unslipping process. It is possible, however, that the mechanism of stage I growth is essentially the same as that of stage 11, but occurring on a much smaller scale.6 In this situation, it has been observed that cracks propagate along slip bands comprising dislocation cell structures and bounded on either side by regions of different dislocation density and distribution." Since there is evidence that such bands are softer than their matrix, * it may be expected that the plastic blunting process occurs within a single slip band during stage I growth, rather than on two gross bands as in stage 11, when the acting stress is greater.= The blunting of the crack tip allowed by coordinated

Jan 1, 1968

By C. M. Wayman, S. R. Rauze

It was recently reported' that the initial transformation in (100) iron whiskers grown in the bcc condition can be nucleated on heating in regions of the whisker which are not necessarily the hottest. Although this behavior was observed1 several times, its sporadic nature precluded any documentation other than occasional visual observations during hot-stage optical-microscope heating experiments. The purpose of this communication is to report how, in one instance, the a-y transformation in such a (100) iron whisker was initiated in a region which was clearly at a lower temperature than an adjacent region which did not transform at all.

Jan 1, 1967

By J. H. Swisher

Two recent papers in this journal1,2 contain experimental evidence for an anomaly in the concentration gradient for tracer diffusion. In both papers, the authors suggest that this anomaly is due to a Gibbs' absorption effect. Their hypothesis is that surface active tracer elements tend to remain in or near the surface adsorption layer, thereby altering the diffusion flux and concentration gradient. It is not clear how the anomaly can be explained in terms of an adsorption effect. Surface tension forces act parallel rather than perpendicular to a surface and therefore should affect only the rate of spreading of surface active agents tangentially across a surface. Frenkel3 has given a short treatment of surface tension as a driving force for surface diffusion. While the equilibrium concentration of a surface active agent at the surface of a solution is known to be higher than in the bulk, its chemical potential is necessarily the same. It is difficult to see how adsorption can result in an anomaly in the chemical potential gradient, which is the driving force for diffusion. A more detailed explanation by the authors of the adsorption mechanism is in order. A similar anomaly does not seem to arise where

Jan 1, 1970

By H. Reginald Hardy, Y. S. Kim

Recent studies of inelastic behavior and acoustic emission in geologic materials further validate the concept that such materials may be considered to consist of an elastic media containing an array of pores and cracks. In the present paper this concept is investigated further by experiments in which the mechanical behavior of a number of geologic materials were studied in detail at low stress levels using ultrasonic pulse methods. Experiments were carried out on cylindrical test specimens of Indiana Limestone, Tennessee Sand- stone and Barre Granite under relatively low confining pressures (0-5000 psi). Analysis of data from these experiments indicated that there existed a low-level critical stress at which there appeared to be a transition in the mechanical behavior of the material. Under triaxial stress, results indicated that the differential critical stress was relatively independent of confining pressure, i.e., the mechanism responsible for the transition in mechanical behavior was governed by a maximum shear stress criteria.

Jan 1, 1971

By G. R. Pickett

Examples are presented which show that the velocity~ amplitude, attenuation and apparent frequency of several acoustic waves can be recorded in the borehole. Examination of such recordings, termed "character" logs, indicates that the wave types observed include a refracted compressional wave and a wave which travels with formation shear velocity. Laboratory data are used to show that compressional and shear wave velocities are dependent on porosity, effective stress and lithology; but that the change in reciprocal velocity per unit change in porosity is larger for shear waves than for compressional waves. We, therefore, conclude that. the accuracy of porosity determinations can sometimes be improved by use of shear wave velocities, provided that the shear wave amplitudes are large enough to delineate the shear arrival from the preceding compressional arrival on the character log. Borehole data are presented which show that the difference between shear wave and compressional wave reciprocal velocities can be used to predict porosities. This is a refinement which may allow the prediction of porosities from single-receiver acoustic logs without introduction of errors from borehole fluid traveltimes. Laboratory and field data are presented to show that the relationship between compressional and shear wave velocities can be used to indicate lithology. An example is presented to show that fractures usually cause a greater reduction in borehole shear wave amplitudes than in compressional wave amplitudes, an effect which may offer a more reliable means of detecting fractures. The complexity of the borehole acoustic wave train can rake presently available cement bond logs highly sensitive to the gate and bias settings used. The character log offers a means to circumvent possible misinterpretations by recording all amplitudes, from which the interpreter can select the appropriate data for evaluating the cement bond. Character logs may also be used as a quality control for open-hole transit-time logs when existence of small compressional wave amplitudes interferes with the proper functioning of bias-controlled timing devices. Evaluation of the potential uses of character log data is not complete; but a character log presented in a form convenient for routine use would be a desirable addition to currently available logs. To summarize, possible applications for such a log in formation evaluation include the following (1) quality control of transit-time logs, (2) refinement of porosity predictions, (3) determination of lithology, (4) improvement of fracture detection and (5) improvement of cement bond evaluation. Suggestions are made regarding the requirements for a suficient but practical character log for routine use. INTRODUCTION Acoustic logs have become a widely used porosity tool in formation evaluation. In addition, there is a growing application of acoustic logs in cement bond evaluation and fracture detection. These applications have mainly involved the use of logs of first-arrival transit times and amplitudes and have not included detailed studies of the complete signal. The purpose of this paper is to show that significant benefits in formation evaluation can be gained by a more complete use of the acoustic wave train generated in the borehole by an acoustic logging tool. We hope that this discussion will also stimulate further development of logs suitable for routine use so that these benefits may be realized. Examples of acoustic wave train logs, termed "character" logs, are presented to show that several identifiable acoustic waves are present in the borehole. The measurable characteristics of these acoustic waves and some of their relations to formation properties of interest are also discussed. The more obvious potential uses of character logs are listed, and some suggestions are made regarding the requirements for a sufficient but practical character log for routine use. CHARACTER LOGS Some 10 years ago, Vogel' and Summers and Broding' noted that the signals received uphole from an acoustic logging tool located in a borehole had a number of interesting characteristics. The logging tool consisted of two or more pressure transducers spaced on an acoustically insulated body (Fig. la). One of the pressure transducers was used as a transmitter to generate pressure waves in the borehole fluid. The other transducer served as a receiver to detect any pressure waves reaching it in the borehole. The receiver then converted these pressure waves to electrical signals which were transmitted to the surface and displayed on an oscilloscope as a record of time vs receiver-signal amplitude. Fig. lb is a schematic representation of a typical record. The interesting characteristics seen in the earlier' and subsequent experiments were (1)

By Ralph A. Sherman, John Blizard

The experimental investigation described in this paper was conducted to determine the relative combustibilities of different samples of blastfurnace coke when burned in a current of air in a small furnace. It was undertaken in connection with the work done by Perrottl and Kinney2 on the process of combustion in the blast-furnace hearth.3 Reference is often made to the "combustibility" of coke by blastfurnace men, but exactly what is meant by the term "combustibility" is somewhat vague. Brassert,4 in a paper before a meeting of blastfurnace men in 1914, refers to combustibility as follows: The value of the coke in relation to the heat reactions in the furnace is determined not only by the carbon content but even more so by its combustibility. This, in turn, is governed by its size, the physical and chemical composition of the carbonaceous substance forming the cell walls, and the interior and surface structure of the coke pieces. These properties are, in turn, influenced by the chemical and physical properties of the coals used for coking, the density of the cake of coal in the oven, the coking time, temperature and heat regulation of the ovens, and last, but not least, by the method of quenching, screening and handling the finished coke. What principally concerns the blast furnace is the rate of progression of the combustion, which depends not so much on the chemical analysis as on the physical qualities of the coke. It is this rate of progression that we term combustibility, which is the speed at which the carbon molecules in the coke combine with oxygen under given conditions. In general, what the blast furnace requires is a coke which will burn rapidly and with intensity at the tuyeres, yet which has a sufficiently strong structure and hard surface to resist abrasion and solution by CO2 in the upper part of the stack.

Jan 1, 1923

By John Blizard, Ralph A. Sherman

The experimental investigation described in this paper was conducted to determine the relative combustibilities of different samples of blastfurnace coke when burned in a current of air in a small furnace. It was undertaken in connection with the work done by Perrottl and Kinney2 on the process of combustion in the blast-furnace hearth.3 Reference is often made to the "combustibility" of coke by blastfurnace men, but exactly what is meant by the term "combustibility" is somewhat vague. Brassert,4 in a paper before a meeting of blastfurnace men in 1914, refers to combustibility as follows: The value of the coke in relation to the heat reactions in the furnace is determined not only by the carbon content but even more so by its combustibility. This, in turn, is governed by its size, the physical and chemical composition of the carbonaceous substance forming the cell walls, and the interior and surface structure of the coke pieces. These properties are, in turn, influenced by the chemical and physical properties of the coals used for coking, the density of the cake of coal in the oven, the coking time, temperature and heat regulation of the ovens, and last, but not least, by the method of quenching, screening and handling the finished coke. What principally concerns the blast furnace is the rate of progression of the combustion, which depends not so much on the chemical analysis as on the physical qualities of the coke. It is this rate of progression that we term combustibility, which is the speed at which the carbon molecules in the coke combine with oxygen under given conditions. In general, what the blast furnace requires is a coke which will burn rapidly and with intensity at the tuyeres, yet which has a sufficiently strong structure and hard surface to resist abrasion and solution by CO2 in the upper part of the stack.

Jan 1, 1923

By W. C. McBee, B. W. Jong, T. A. Sullivan

A sulfur concrete technology has been developed by the US Bureau of Mines, where chemically modified sulfur is used with suitable mineral aggregates to produce construction materials that are resistant to corrosion by acids and salts. This report presents a summary of the basic technology and results of testing the materials under actual operating conditions in 50 corrosive environments in 40 commercial plants. After four years of testing, there was essentially no evidence of material degradation or loss of strength. Regular concrete materials were attacked and, in some cases, completely destroyed under the same conditions. Testing is continuing to establish ultimate longevity and durability of the sulfur concretes. The materials are finding widespread applications in metallurgical, chemical, and fertilizer processing plants.

Jan 1, 1986

Discussion of the paper of J. IV. GWINN, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 239 to 247. GIRARD B. ROSENBLATT, Salt Lake City, Utah (communication to the Secretary*).-The storage-battery locomotive certainly has its place in metal mining and I an) glad to note that it is now receiving the recognition that is its clue. It is, however, not a panacea for all conditions of mine haulage. There are places where it will not work to advantage and cannot compare with` the trolley-type locomotive in cost of operation or in cost of maintenance. On the one hand, there are places where it clearly outshines the trolley-type locomotive. Much depends on the headroom available in the drifts and on the condition of the roof. For short hauls with moderate-

Jan 5, 1915

By Edgar R. Kendall

A knowledge of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. Locating the Supply The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1942

By C. E Shoenfelt, Gail F. Moulton

Proven and developed oil reserves, and productive capacity increased during 1943 in the fieids of the Rocky Mountain region. Oil production during the year was nearly 45 million barrels, or slightly less than in 1942. The rate of production at the start of 1944 was slightly less than at the start of 1943. Pipe-line projects scheduled for completion during 1944 should permit a substantial increase in the rate of production. Wildcat exploration was more extensive in Montana during 1943 than in other states in the region. The results of wildcat drilling were unsatisfactory, although new oil fields were discovered on the Gebo, Little Buffalo Basin and Steamboat Butte structures of Wyoming, the Gage anticline of Montana, and the Clark Lake structure of Colorado. The area of the structures on which the discovery wells were drilled is known to be considerable, but further drilling is required to determine the importance of these fields. The most important increase in proven reserves resulted from the drilling to newly discovered deeper producing formations in the Elk Basin and other fields of the Big Horn Basin area of northern Wyoming. Lack of a market and unfavorable prices for heavy black oils had prevented complete exploration of favorable areas in the Rocky Mountain region for many years. In particular, the effect on further exploitation of the Big Horn Basin area had been quite serious. The increased demands for all oils created by the war and an increase in price in February 1943, combined later with Government approval of construction of pipe lines from the Big Horn Basin area to the Billings and the Casper districts, provided a basis for undertaking a drilling program. The important additions to reserves were made by drilling in previously discovered fields. The newly discovered fields resulted from drilling on favorable structures which had been known for several years. A continuation of the favorable results obtained during 1943 seems possible only if further testing of the newly discovered fields is satisfactory and if drilling on less favorable known structures or geophysical prospects results in the discovery of new fields. The amount of drilling in the Rocky Mountain states of Colorado, Montana and Wyoming, was about the same during 1943 as .in 1942. However, owing to the fact that a number of wells of large potential production were completed in the Elk Basin field, the total initial production of the prodicing wells was- nearly twice as great for 1943 as for 1942. Explorational activity at the end of 1943 seemed to be directed to geophysical methods, which are required to discover structures hidden beneath the rocks of Tertiary age in the Powder River and other large sedimentary basins. It is in

Jan 1, 1944

By Edgar R. Kendall

A knowledge of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. Locating the Supply The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1942