Search Documents

By R. J. Wasilewski

Elastic constants have been determined on single crystals of maximum-melting-temperature NiAl compound (50.6 at. pct Al) at 25°C. Temperature variations of Young&apos;s modulus in the three principal crystal directions between -150°C and +800°C exhibit no anomalies similar to those repovted for the isomor-phous compounds brass and AuCd. It is concluded that the ordered CsCl structure is stable throughout the temperuture range investigated NICKEL aluminide is a congruently melting inter-metallic compound of CsCl (B2) structure, stable over a rather wide composition range (40 to 54 pct Al). It exhibits a lattice-parameter maximum of a. = 2.883A at 50.6 pct 1,&apos; at which composition the excess aluminum atoms are randomly distributed on the vacant nickel sites;&apos; at higher nickel compositions the excess nickel atoms replace substitutionally in aluminum sites, while at higher aluminum compositions vacancies are present in the nickel sublattice.&apos; For compositions close to NiAl no significant variation in order has been observed at temperatures up to 900°C.3 At high nickel (65 pct) compositions the existence of a martensitic structural transformation has been reported.4 NiAl is isomorphous with the ordered B-brass structure and with the high-temperature structures of AuCd and TiNi alloys close to equiatomic composition. All of these exhibit anomalous elastic behavior as the temperature of their diffusionless transformation to lower-symmetry structures is approached.&apos;-&apos; This behavior has been explained as indicative of low stability of the CsCl structure in these compounds.8 The present paper reports the experimental determination of the elastic compliances of single-crystal NiA1. EXPERIMENTAL METHOD 1) Specimens. Polycrystalline NiAl was prepared by induction melting of carbonyl nickel and high-purity aluminum and casting into solid copper molds in gettered helium atmosphere. The castings thus produced were canned in mild steel and impact-extruded at 1100 to 1200°C to 38-in.diam rod. After the steel sheath was pickled off, the rods were converted to single crystals by repeated high-frequency satisfactorily produced the desired orientations in the form of crystals 38 in. diam by 8-12 in. long. These were subsequently center less-ground to 7 to 8 mm diam by 12 cm long, electropolished (in 80 pct methanol, 20 pct HzSO, at 25°C and 15 v), and their axial orientation determined to 1 deg by the Laue back-reflection technique. The rod dimensions were determined to 0.01 mm and the densities determined from geometrical dimensions and the weight of every specimen. The average density was 5.905 0.005 g per cu cm. 2) Elastic Data Measurements. Room-temperature elastic compliances Sii were obtained by determining to 0.1 cps the fundameGtal resonance frequencies in the longitudinal and torsional vibration modes. At these frequencies the following relations hold: E =p(2lfif =pvl= Sn- 2r[Sll- S12- -£„«] g -P(2iftf = pvf = (s<« - fr(sii - sw - ±s»y where vl and vt are the velocities, and f andft the resonance frequencies of the longitudinal and torsional waves, respectively; 1 is the length of the specimen, and r is the direction cosine factor—{cos2 a • cos2 0 + cos2 a . cos2 y + cos2 0 ¦ cos2 Y}. Given three crystals of orientations (loo), (110), and (111)) i.e., F = 0, 14, and 13, we can obtain six equations for the three unknown compliances, thus providing adequate internal check. Mode mixing can readily occur in the relatively long wavelength resonance utilized here. This could cause a significant error in the torsion wave velocities calculated from the apparent resonance frequenies. Therefore, throughout the present work, a method, described previosl,&apos; was used to ensure that no significant mode mixing took place at resonance. The apparatus used was originally designed for the Elastomat, Magnaflux Corp.. Chicago, 111. determination of flexural vibration resonance frequencies. At room temperature torsional vibration mode could be established by suitable positioning of the thin wires from the input and pick-up transducers, and longitudinal mode by cementing thin magnetic foils at the ends of the specimen, and inducing the vibration by means of electromagnetic transducers. Only flex-ural resonance frequencies could, however, be obtained reproducibly over the temperature range of -150 to 800°C. These data are considerably less accurate, the error in the modulus being estimated at -0.6 pct from the specimen dimensions and the room-temperature Poisson&apos;s ratio. The reproducibility of the resonance frequencies in repeat runs was, however, to better than l in 15,000, hence the relative elastic modulus error less than 0.02 pct. Therefore, the temperature variation of the principal Young&apos;s moduli obtained by flexural resonance, relative to room-temperature values, is believed to be satisfactorily accurate.

Jan 1, 1967

By J. C. Trantham, J. W. Marx

From 1955 to 1958 the Phillips Petroleum Co. conducted a series of small scale counterflow combustion field tests in a tar sand about 60-ft deep and 6 to 12-ft thick near Bellamy, Mo. A total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern, were employed. Electric heaters, gas burners and wellbore fuel packs were tested as counterflow ignition devices. Direct drive ignition followed by reversal to counterflow operation was not possible in this case because of formation plugging by the semi-solid tar during the direct drive phase. Sustained counterflow burning was achieved with wellbore fuel packs under conirolled conditions which permitted close correlation of fire front velocity, air velocity, air-oil ratios and yields for a wide variation in process parameters. The tar in place was about 10&apos; APl with a reservoir viscosity greater than 500,000 cp. The composite oil prodlcct was 26&apos; API with a viscosity in the range of 5 to 15 cp. Vertical sweep efficiency in the line drive pattern was essentially 100 per cent, with no evidence of gravity segregation. Original tar in place ranged between 800 and 1,000 bbllacre-ft, specific rock permeability averaged about 800 md before burning and effective air pemeability with residual oil and water in place (at the time of ignition) averaged 250 md. The volume of oil recovered during stabilized line drive counterflow burning represented about 67 per cent of the volume of tar originally in place in the burned out zones. A minimum was found when air-oil ratios were plotted against formation air velocities, and a limiting air velocity existed below which the counterflow fire front reversed and burned back over its own trajectory, using the residual coke left behind. INTRODUCTION Early in 1955 the Phillips Petroleum Co. began preparations to field test counterflow underground combustion as a method for producing oil from high viscosity hydrocarbon deposits, such as bituminous (tar) sands. At that time all published information on the use of underground burning io increase oil recovery was based on the direct drive process, in which the fire front moved through the formatim in the same direction as the injected air stream. Such direct burning is not applicable to many heavy oil sands or to most tar sands because the heat-thinned native hydrocarbon congeals in the cold rock ahead of the fire front forming a gas permeability block which smothers the combustion. Laboratory experiments first demonstrated that this permeability blocking would not occur if the fire front and the air stream moved in opposite directions. In this counterflow (reverse) burning process the heated heavy oil or tar is driven back through the combustion zone. Here thermal cracking produces relatively light hydrocarbon products which pass through the heated rock behind the fire front (largely in the vapor phase) and are incapable of causing a gas permeability block.&apos; Exploratory wring revealed that consolidated bituminous sandstones with a combination of tar saturation, permeability, thickness and depth favorable for experimental field testing existed at several points in western Missouri. By the fall of 1955, a test site for determining technical feasibility of the counterflow process under field conditions had been selected near Bellamy, Vernon County, Mo. — about fifty miles north of Joplin. The pay zone was too thin and too shallow to constitute a commercial prospect, but these same factors permitted controlled experimental operation with a small compressor installation and with a large number of monitor wells. These were needed for adequate observation of the underground phenomena at reasonable cost. RESERVOIR CHARACTERISTICS The reservoir chosen for the experimental field tests was a 124 thick section of tar sand extending from 49 to 61 ft subsurface, with shale and siltstone laminations sealing the top and bottom. This section was part of a larger 30-ft thick tar sand deposit which extended both above and below the test zone. Core analyses showed that the 12-ft sand was effectively subdivided into two approximately equal sections, with the lower zone being consistently more permeable than the upper zone. The most significant laboratory core data are summarized in Table 1. The line drive test which is the principal subject of this report utilized only the lower 6-ft thick zone, with the upper zone regarded as part of the 55-ft overburden. WELL PATTERNS The over-all field test program involved a total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern. In some of the tests the full 12-ft zone was employed; in other cases only the more perme-

Jan 1, 1967

Abbey, Robert Graham, District Mgr. The W W. Sly Mfg. Co,. 50 Church St, New York, N. Y. &apos;21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd ..Concepcion del Oro, Zac., Mexico. &apos;23 Abbott, Argyle Campbell, Dev. Dept, E I du Pont de Nemours & Co, Wilmington, Del. &apos;29 Abbott, Clarence E., V.P, Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co, 1242 Brown-Marx Bldg, Birmingham, Ala. &apos;04 Abbott, Louis Benjamin, Chief Engr., Elkhorn Div., Consolidation Coal Co, Jenkins, Ky. &apos;15 Abeel, George H., Jr., Cons. Min. Engr Box 427, Santa Monica, Cal. &apos;18 Abel, Albert E., Asst. to Pres, Valley Mould & Iron Corp Hubbard, Ohio. &apos;19 Abel, Raymond L., Asst. Prof., Dept. of Pet Refin., Univ. of Pittsburgh Pittsburgh, Pa. &apos;28 Abell, Leo M., Research Engr, Sullivan Concentrator Chapman Camp, B. C., Canada. &apos;31 Abernathy, George Elmer, Prof. of Geol. & Min . Kansas State Teachers College, Pittsburg, Kans. &apos;20 Aborn, Robert H., Research Lab, U. S. Steel Corp. Lincoln Highway, Kearny, N. J. &apos;19 Abozeid, Mahmood, Dept. of Mines & Quarries Cairo, Egypt. &apos;26 Abraham, Arthur W. Box 1466, Bakersfield, Cal. &apos;20

Jan 1, 1923

By Walter E. Hopper

The Caddo oil-field, shown in Fig. 1, is located in Caddo parish, northwestern Louisiana. The known producing territory of oil is covered by townships 19 N, 20 N, 21 N, 22 N, and ranges 15 and 16 W., shown in Fig. 2. The center of the field may be taken as Oil City, 24 miles north of Shreveport, on the Kansas City Southern railway. Shreveport is the second largest city in the State, and is the connecting point of five railroad-lines. Drilling at the present time, however, is going on all over northern Louisiana, especially in Caddo and the neighboring parishes. During the winter of 1908-09 I spent &apos;four months in the Caddo field, under the direction of the Louisiana Geological Survey and the U. S. Geological Survey. II. History and Development. Natural gas escaping at the surface is found at numerous places in northwestern Louisiana. At Shreveport, the plant of the Shreveport Ice & Refrigerating Co. has been lighted by natural gas for 20 years. The well was drilled for water, but was abandoned on account of the gas. A test well, put down in 1905 near the western limits of Shreveport, was driven to 1,650 ft., and encountered indications of gas and oil at various depths, but did not succeed in finding enough to be profitable. Attention was first attracted to the Caddo field in 1895 by indications in water-wells from 40 to 60 ft. deep, in which the pressure of natural gas was noticeable. This indication of gas in a shallow well led to the drilling of the first well in the Caddo field, the old Savage Brothers & Morricell, or the Caddo Lake Oil and Pipe Line No. 1. The rig for this well was erected in May, 1904, and drilling began in June, 1904. The well was bailed Mar. 23, 1905, with a small amount of oil. It was deepened July, 1905, and converted into a "gasser" Jan. 3, 1906. It was abandoned January, 1907. In consequence of the finding of oil in the Savage well, drilling-operations were pushed with energy; and in April, 1905,

Jan 1, 1912

By Linn M. Farish

The estimated production of petroleum in the Dominion of Canada for 1931 was 1,582,000 bbl., an increase of 60,000 bbl. over 1930. Nearly all of the production came from Alberta, with a small quantity from Ontario, and a very minor amount reported from New Brunswick. At the beginning of 1931 it was hoped, and predicted, that a substantial increase in production would be shown for that year, but such was not the case, since Alberta did not show the anticipated gain. The production from Ontario and New Brunswick has not varied more than a few thousand barrels during the past 10 years and aggregated 124,000 bbl. in 1930, with 126,600 bbl. estimated for 1931. Unless new fields are discovered, production in 1932 will decline, with Ontario and New Brunswick showing little change and Alberta declining appreciably. Canadian production by provinces during the past 10 years is given in Table 1. Furnished by the Dominion Bureau of Statistics. a Barrels of 35 Imperial gallons or 42 U. S. gallons. c Figures for Ontario and New Brunswick are estimated. The production of natural gas in Canada reached the record figure of 29,377,000,000 cu. ft. in 1930 and it is estimated at 26,874,600,000

Jan 1, 1932

By E. H. Hamilton

THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total 100.0 THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total?100.0?20,580

Jan 1, 1924

By J. D. Cooner

SINCE my working life of 32 yr has been spent in and about the anthracite mines of the Hudson Coal Co., and the previous 4 yr in a college school of mines, I can write best about the safety program of a coal mining company. However, most of the suggestions, statements and practices mentioned herein are applicable to the members of a safety organization and program of almost any industry. It is realized that industrial officials actually interested in real safety work are fully acquainted with the requirements of a practical safety program. Therefore, for such persons there may be nothing new in this paper. The Hudson Coal Co. of Scranton, Pa., employs 7,000 men and produces 5,000,000 tons of anthracite annually at nine collieries scattered for a distance of 40 miles throughout the Lackawanna and Wyoming valleys of northeastern Pennsylvania. For the past 17 yr of the above mentioned 32, I have been engaged in safety work as a safety inspector, assistant mine superintendent, and at present the safety engineer. I have also had the privilege of visiting coal and metal mines in other parts of the United States and Canada. We Americans are the most careless people in the world. If any one doubts this statement why are 100,000 of our people killed accidentally annually? Or why during the almost four years we were engaged in World War II were more of our people killed accidentally at home than were killed in our army, navy, marine corps, coast guard, and other services during the same period? We are careless everywhere in our homes, on the highway, at work and at play. The purpose of this paper is to outline the requisites of a safety department and its program to stop the accidents occurring to employees at work in mines or industrial plants. The first requisite for a safety program is that the management must be convinced of the need and value of a real safety program. By "management" is meant each department head from the president down. Otherwise a good safety department with a good safety program will not succeed because it will not have the proper personnel and equipment to work with, its rules and regulations will not be enforced, and the members of the safety department will be belittled in the eyes of most of the workmen and supervisors. Next, a safety engineer and his inspectors should have worked in the production end of the mines as workmen and also in an official capacity. They are then in a position to have practical and first hand knowledge of the accident hazards of the industry, how to prevent them, and in general the problems of both the workmen and officials. Some men are appointed as safety inspectors when they are physically unable to carry on as mine officials. Such men may know the safety end of the industry and even be safety-conscious, but if they are physically unable to be mine officials they are also physically unable to be safety inspectors, as a safety inspector in our mines must walk from 2 to 4 miles on each daily inspection-and visit each working

Jan 1, 1948

By Richard W. Bayley

The Atlantic City district encompasses several districts and has been previously called by different names, e.g., Atlantic gold district, Atlantic City-South Pass mining district, and Sweetwater mining district. The district is located in a terrane of folded and faulted early Precambrian metamorphic rocks which lies near the south end of the Wind River Range in Fremont County, Wyoming, Historically it is a gold district of little production, but today is an iron district of considerable importance. Gold was discovered in placer deposits about 1842 and in quartz-arsenopyrite veins about 1867, after which there occurred a mining boom lasting a few years. Minor, intermittent gold production from placers and lodes has continued to date, but the total production has probably not exceeded a few millions of dollars. Past lode mining was generally shallow ( in the oxidized zone), the deepest about 3 60 feet. The deeper, less oxidized and sulfide ores on the same lodes have not been explored. They appear to hold the only hope for future gold mining. Sedimentary iron-formation, similar to the Lake Superior taconite, occurs in the northern part of the district. Locally, where the ironformation is thickened by folds and faults, sufficient tonnages are present to be minable, as at Iron Mountain, where the U.S. Steel Corporation produces about 1.3 million tons of iron-ore pellets annually. Exploration of the iron deposits began in 1954, and the first ironore pellets were shipped to Provo, Utah in August 1962. Indicated reserves of iron-formation (about 30 per cent Fe) are reported to be about 300 million tons.

Jan 1, 1968

By AIME AIME

CONCIDENT with what promises to be a record-breaking year of activity in the world&apos;s greatest iron-ore district is the announcement of plans to hold the regional meeting of the American Institute of Mining & Metallurgical Engineers at Duluth, Aug. 12 to 15 in¬clusive. More than 25 open-pit mines will be in operation in Minnesota&apos;s great iron-ore district this year, affording to those attending the convention an unusual op¬portunity of viewing practically side by side the interesting activities of power-shovel operations, railway haulage, truck haulage, conveyor-belt haulage, tower-excavator operations, iron-ore concentration, and underground mining. The ore can be followed from the mines to washing and concentrating plants and to the docks and lake carriers on Lake Superior, where an average of one boat of 10,000 tons&apos; capacity will be loaded and depart every 15 minutes, day and night, during the 1941 shipping season.

Jan 1, 1941

By Arnold K. Reese

It is not the purpose of the writer to set forth in these notes anything new or surprising in blast-furnace practice, but simply to lay before the Institute the somewhat unusual results obtained during a period of six consecutive months, ending April 30, 1896, at the Dover furnace of the Penn Iron and Coal Co., and to give, with these results, the conditions under which they were obtained, and all figures pertaining to that period. This plant was entirely rebuilt, on thoroughly modern and improved plans, in the spring of 1895, by Frank C. Roberts & Co., of Philadelphia.

Jan 1, 1898

By Alan M. Bateman

Before World War II we proudly considered that we were the nation of all the world most richly endowed in mineral resources. We knew it was no accident that those countries abundantly supplied with mineral resources became the great manufacturing nations, and the politically and militarily strong ones; and that our own great industrial cities sprang up where coal and iron met. We all reallized, especially we of the mining profession, that the energy of fuels and the solidity of metals spelled industrial growth and in turn industrial might and that other nations came to regard mineral self-sufficiency as one of the chief goalsof economic nationalism.

Jan 1, 1949

By Donald L. Katz

FIFTEEN years ago Dr. Manning published a paper in "Petroleum Development and Technology" on &apos;.Fundamental Research Relating to Petroleum." He tabulated for several industries "the proportion of their present success which can be fairly attributed to the application of information and processes obtained by scientific research," giving petroleum a score of 7 compared to 100 for the electrical and coal-tar industries. Today the petroleum industry as a whole and the producing groups both have raised their score beyond the majority and are climbing toward the top. Present practices are being developed both by fundamental research and the application of the research method in field operation.

Jan 1, 1941

By J. O. Brittain, E. Lautenschlager

Yield point measurements were made on polycrys-talline specimens of a iron deformed various amounts at 770, 1950, or 273°K, aged, and redeformed at 77: 195°, or 273°K. When the prestrain temperature is lower than that subsequent to aging, the yield point return is suppressed relative to specimens deformed at the same temperature both before and after aging. The degree of suppression is a function of both the magnitude of prestrain at the lower temperature and the difference between the deformation temperatures before and after aging. It is proposed that the suppression is caused by the formation of dislocation barriers during the initial low-temperature deformation. The aging kinetics of polycrystalline a-iron wires deformed at 77o or 303oK were studied at 44 " and 64 "C using internal friction measurements. No change was noted as a result of the difference in prestrain temperature. IN an earlier investigation1 it was observed that the return of the yield point was suppressed when a poly-crystalline specimen of a iron was plastically deformed at 77oK, aged at room temperature, and subsequently tested at room temperature. In order to investigate this observation, a research program was undertaken to measure the effect of prestrain temperature on the strain aging of a iron.&apos; According to Thomas and Leak,3 return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solution, while the return of the yield point as a function of aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,4 the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point upon restraining. In this experiment, both methods of measuring strain aging were employed in order to have two independent measurements of the strain aging phenomenon. In a previous study,5 the strain aging kinetics of a similar lot of a iron were measured for specimens which were prestrained and tested at the same temperature over the range of 77" to 273°K. Although some differences were found in the correlation of the two methods employed for measuring strain aging, the kinetics of strain aging were unaffected by the change of prestrain and test temperature. In another study,6 dislocation line tension and the density of the solute atmosphere were found to contribute to the return of the yield point when ingot iron specimens were prestrained at 303°K and tested at a lower temperature, namely 77°K. This paper is concerned with changes in strain aging kinetics produced by pre-straining at 77" to 303°K and testing at either the prestrain temperature or at higher temperatures up to 273°K. EXPERIMENTAL PROCEDURE The polycrystalline a iron specimens used in both the tensile and internal friction tests were 0.033-in. diam ingot iron wires, wet hydrogen treated and re-carburized. A more detailed procedure for processing a 3/16 in. ingot iron rod (nominal wt. pet composition: Fe - 0.013; C - 0.0125; Mn - 0.023; Si -0.005; P - 0.0023; S - 0.11; Cu - 0.004 N) to 0.033 in. diam specimens containing approximately 0.020 wt pet C and no detectable nitrogen with a grain diameter of 0.033 to 0.040 mm is given elsewhere.5 Immediately prior to testing, specimens were solution treated for 15 min at 700o ± 2°C in a static vacuum of less than 50 ?. of Hg and rapidly quenched into an ice-water bath while still enclosed in a 3 mm quartz vial. The internal friction specimens had 8-in. gage lengths and the tensile specimens had 2-in. gage lengths. The wires used as tensile specimens were first run as internal

Jan 1, 1962

[Separates of all the Pamphlets published within the last three years (starting with No. 1469) are available, with few exceptions, at Institute headquarters. Separates of all the Technical Publications are also available. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute.] METAL MINING TRANS. PAMPHLET VOLUME NUMBER TITLE AUTHOR MEETING AND PAGE* -1033 Relation of Air Pressure to Drilling H. W. Seamon New York 66,743, 766 Speeds of Hammer Drills Feb., 1921 1034 Time Factor in Depletion of Mines J. W. Roberts New York - 66,711 Feb., 1921 1 1035 Calculation of Ore Tonnage and Grade J. E. Harding New York 66, 117, 122 from Drill-hole Samples- Feb., 1921 1038 Discussion of Papers Presented in 1920 1041 Run-off and Mine Drainage - H. N. Eavenson New York 66, 624, 630 Feb., 1921 1043 The Health of the Underground Worker A. J. Lanza New York Feb., 1921 1045 Dust-ventilation Studies in Metal D. Harrington New York 66, 272, 282 Mines Feb., 1921 1046 Discussion of Papers Presented at New York Meeting, 1921 1072 Breakage and Heat Treatment of Rock- B. F. Tillson New York 66,758 drill Steel Feb., 1921 1073 Discussion of Papers Presented at New York Meeting, 1921 1076-M Analysis of Some Drill-steel Tests F. B. Foley New York - 66,789 Feb., 1921 1077-M Application of Magnetic Analysis to C_ W. Burrows New York 66,796 Root Drills Feb., 1921 1078-M Heat Treatment of Rock-drill Steel G. H. Gilman New York 66,779 Feb., 1921 1080 What is the Ideal Drill Steel? F. H. Kingdon New York 66,807 Feb., 1921 1081 Rock Drill Steels, etc. W. T. Ober New York 66,814 Feb., 1921 1082-C Underground Mine Development, Its J. B. Dilworth Wilkes-Barre 66, 715, 721 Definition and Valuation Sept., 1921 1084 Drill Steel from Hollow Ingots P. A. E. Armstrong New York 66,809 Feb., 1921 1088 Authors&apos; Replies to Recent Discussion 1092 Heat Treatment of Rock Drill Steel A. E. Perkins New York 66,811 Feb., 1921 1096-M Octagonal Ventilation Shaft of Davis- J. L. Bruce Wilkes-Barre 66, 252, 268 Daly Copper Co. Sept., 1921 1100-C Determination of Electrical Equip- G. Bright Wilkes-Barre 66, 580, 605 ment for a Mine Hoist Sept., 1921

Jan 1, 1926

By T. A. Wright

THE SAMPLING of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called "metallic button" or "metallic recovery" or "metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can he readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also. As a matter of fact, we may expect that improved refining processes will make possible the partial recovery of lead and tin which are now lost.

Jan 1, 1928

By S. T. Wlodek

The scale md subscale reaction products were identified and their rates of formation were studied in air over the range 1600" to 2000°F (871 " to 1149°C) for periods of up to 400 hr and for hoth the solution-annealed and aged conditions. The effect of prior sltrface preparation on suhscale oxidation was also studied The general oxidation behavior of both Ni-Cr-Mo-Al-Ti type alloys was similar. A surface film of a, Al2O3, forms immediately on exposure Subsequent oxidation continued at a linear rate (QL = 55 * 5 kcal per mole) as colonies of Cr2O3 nucleated at the A12O3/gas interface Further oxidation proceeded at a paraholic rate zvhiclz could he fitted to two successive rate constants. During paraholic oxidation, and depending on temperature, the scale consisted of Cr2O3, NiCr2O4 , and TiO2 with traces of NiO. In the case of Rene 41, the activation energy of both paraholic processes was 66 * 3 kcal per mole suggesting that diffusion of cations tlzrozrgh Cr2O3 was the rate -determining process. An unusual decrease in the oxidation of Udimet 700 at 1900°F where a spinel of Ni(A1,Crh0, zuas the predominant reaction product prevented the accurate assignment of activation energies for this composition. In both alloys internal oxidation of Al2O3 commenced shortly after parabolic scaling was observed. Prolonged exposure prod7tced intemal oxidation of TiN, and in Udimet 700 a complex Mo-Ni nitride was also found. At 1900oF, the subscale reactions in Udimet 700 undergo an inversion which parallels the decrease in surface oxidation; internal oxidation ceases hut is replaced by the formation of "spherodized" 3.&apos; colonies. Surface-preparation techniqtles which introduce appreciable working, such as coarse surface grinding or grit blasting. increase the amount of alloy depletion and internal oxidation in Reni 41. The reverse is true of Udimet 700 for which electropolished or mechanically polished specimens show much more subscale oxidation than strongly worked stirfaces. The strongest commercial nickel-base alloys presently available are generic to the Ni-Cr-Mo-A1-Ti base which exploits the precipitation of Ni3(A1,Ti) as the main strengthening mechanism, while relying on solid-solution strengthening by molybdenum and chromium reinforced by the pre- cipitation of carbides to attain maximum properties. This study characterizes the oxidation behavior of Rene 41, the strongest alloy of the Ni-Cr-A1-Ti type commercially available in sheet form, and Udimet 700, whose higher aluminum and titanium content allows it to exhibit one of the more attractive combinations of high-temperature properties available in a wrought product. The scaling processes of complex, type nickel-base alloys have received relatively little attention. Malamand and vidal as well as Poulignier et al.2&apos;3 have determined the composition gradients across the metal/oxide interface produced by high-temperature oxidation and considered the effect of surface perature, Limited weight-gain data has also been published by Fere 5 for alloys of this type and Radavich6 has identified the reaction products on Udimet 500 and Inco 702 after oxidation at 1832°F. Reference can, of course, be made to the excellent reviews of Kubaschewski and Hopkins7 or Ignatov and Shamgunova8 for a summary of the data available on the oxidation of binary and ternary alloy systems which are related to the more complex alloys considered here. EXPERIMENTAL The analyses of the different commercial heats studied are given in Table I. Using the experimental procedures previously established,9 continuous weight-gain data were obtained on both heats of Rene 41 sheet (A and B) and 150-mil-thick slices of cast Udimet 700. Subscale oxidation reactions were followed by static exposure of cylindrical specimens obtained from swaged Rene 41 (Heat C) and Udimet 700 (Heats E and F). In brief, continuous weight-gain tests were performed on specimens with a surface area of 10 to 12 sq cm. These were abraded through 600 grit Sic paper, electropolished to 2p rms in an electrolyte of 10 pct H2So4 in ethanol, and lightly etched in 10 pct HCl in ethanol before final washing and rinsing in ethanol. All continuous weight-gain data were obtained in dried (-70°F dew point) flowing (1 liter per min) air to an accuracy of +0.1 mg. Subscale oxidation processes were followed by the metallographic examination of 0.5-in-diam by 1.0-in.-long specimens. After an initial center-less grinding, various additional surface treatments were employed to determine the effect of surface preparation on subscale oxidation processes. Before exposure in zirconia crucibles, all samples were lightly etched in 10 pct HCl-ethanol, washed in ethanol, and dried. The depth of internal oxidation was measured to ±0.00025 in. on unetched specimens mounted so as to provide a taper mag-

Jan 1, 1964

By Elmer W. Pehrson

NINETEEN FORTY-SIX was an eventful year for the mineral industries. Perhaps the most significant development was the socialization of industry in Great Britain, initiated in 1945 but carried to fruition in the coal industry in 1946. On Jan. 1, 1947, management of the coal industry will be vested in a National Coal Board, responsible to the Ministry of Fuel and Power. A sum of £164,660,000 has been provided to compensate private owners for assets transferred to the Board. The British coal industry has been a problem for many years. Production has declined to a point where serious shortages of fuel for domestic needs have developed. Exports have dwindled to a small fraction of the previous trade. Costs have increased greatly, and quality has deteriorated. The industry&apos;s physical plant has not kept pace with the rapidly mounting wage scales in recent years. Some claim that the best and most accessible coal reserves of Britain are heavily depleted. The industry has been harassed by difficult labor problems, including bad morale among the workers and a shrinking labor force.

Jan 1, 1947

By L. F. Pett

ALTHOUGH Kennecott&apos;s orebody has long been outlined, it is still necessary to define further its limits. This mine, long an advocate of churn drill methods, recently supplemented its practice by using a diamond drill. So far, the diamond drill holes have been along the main canyon floor which traverses the mine area. This zone, highly fractured, is cut by numerous friable quartz veinlets encountered within the porphyry. These veinlets, formed by filling contracted porphyry fractures with hot, siliceous, mineral-bearing solutions, are often more highly mineralized than adjacent porphyry. They pulverize on contact, yielding only slight amounts of core. For this reason neither analysis of core recovered (amounting to 37.5 pct of approximately 10,000 ft of hole drilled) nor sludge analysis considered separately would give correct assays. The following equation has been adopted: actual weight theoretical actual weight core — theoretical weight sludge Drilling is done un.der contract. Collection of core and sludge samples together with double-checked assaying is done by the company. Microscopic, specto-graphic, and X-ray examination of rock specimen saved is carried on at the University of Utah. A fund, set up by Kennecott Copper Corp. at the University, has encouraged cooperation in solution of mining research problems. The drill used is a Longyear hydraulic powered by a Waukesha 26-hp gasoline motor. A pump, Bean Royal type, is powered by a 7-hp Briggs-Stratton gasoline motor. Weight of unit is 4000 lb and is placed under tripod of 35-ft wood poles within a 25-ft sq area. The following results have been attained: Avg depth of hole drilled, ft 1215 Avg drilling depth per 8-hr shift, ft 10.11 Core Size, In. Avg depth of NC casing, ft 21 2 11/16 Avg depth of NX casing and size core, ft 178 2Ye Avg depth of BX casing and size core. ft 427 1% Avg depth of AX casing and size core, ft 585 1 5/32 Through the use of metal sludge collection boxes, 12 ft long, 18 in. wide, and varying from 12 to 24 in. in depth, sludge recovery has been maintained above 95 pct. Samples, both core and sludge, are assembled for each sample interval and averaged in 50-ft bench increments. Determinations for mineral values are made at both the mine and mill. Assay results varying in excess of 0.05 of copper assay values are rerun to determine correct assay. The organization chart for the Kennecott Utah copper mine is shown in Fig. 1. The Utah mine requires approximately four men per shovel shift to drill solid rock, properly slope banks, and trim loose material from the top of bench sections in making them safe for men and equipment working below. During recent years, while the mine has been worked day and night, powder crews have worked day shift only. Series of toe holes drilled back of advancing electric shovels comprise approximately 70 pct of all mine drilling. These holes, spaced about 21 ft apart, have a depth of 24 ft. Of the footage drilled, 25 pct is for vertical holes either 24 or 28 ft deep, spaced about 28 ft centers along the top rim of banks. This combination of toe holes, using an Ingersol-Rand DA 35 drifter mounted on a tripod and the vertical holes using an Ingersol-Rand Type X71 wagon drill is standard practice above the pit elevation. These benches are 68 ft high, with a few exceptions, while benches below the pit elevation are 50 ft high and require very little drilling other than toe holes. Five benches, varying in height from 80 to 100 ft, require a combination of toe holes plus vertical holes and bank holes or electric churn drill holes. Bank holes using the DA 35 drifter and electric churn drill using Bucyrus-Erie Model 29T, account for 5 pct of feet drilled. Until the past year, drilling of fill material on upper levels was accomplished by churn drill method. Wagon drills are now used for fills because they can be set up and drill a hole an hour. It is necessary to run an air drill 7 hr for each 8-hr shovel shift. Average drilling rates during the past year were as follows: DA 35 drifter using 2 and 3-man crews — 4.36 ft per man hr X 71 wagon drill using 2-man crews — 6.45 ft per man hr DA 35 drifter bank holes, 3-man crews — 2.53 ft per man hr Bucyrus-Erie churn drill, 2-man crews —1.9 ft per man hr Total mine avg — 4.57 ft per man hr Mine practice assigns powdermen to job locations where they perform all drilling and blasting work within the area. Almost as much labor is consumed in springing and loading holes as in drilling them. Average powder consumption is approximately as follows: Per Electric Shovel Shift, Lb To spring and chamber holes — 50 Blasting — 500 Trim banks — 50 One fifth of all powder used is Hercules hercomite bag powder while four fifths is Hercules gelamite 65 pct strength in 1 Vi in. x 8 in. sticks. Frozen material, overhanging from top banks, creates a winter hazard to shovel operators and equipment. Experiments are being conducted with a high-speed Hercules powder in an effort to eliminate this condition. Banks are trimmed by powdermen who lodge 8 or 10 bundles of powder, containing 15 or 20 sticks each, across the upper surfaces of each working face. To each bundle of powder is attached a primer with 6-ft fuse which is lighted as the powdermen, who have lowered themselves down the bank on ropes, ascend to safety. Three angle dozers, D8 caterpillars, make grades and move supplies for the average 31 drilling machines working daily. Compressed air is furnished by three Ingersol-Rand compressors, each with rated capacity of 3750 cu ft of air per min at 100 lb reservoir pressure.

Jan 1, 1952

By Goodman, Richard E.

A complete rational analysis for design of excavation slopes and loaded rock masses is a desirable but perhaps unattainable goal. Irregular external and internal boundary conditions, poor understanding of failure criteria for large masses of rock, capricious material properties, and the importance of indeterminate forces and inaccessible and virtually un- sampleable rock defects emphasize the importance of experience in this aspect of rock engineering. The experience must be correlated with geological factors. In certain regions the accumulation of such experience through the observation of existing rock slopes in various formations constitutes an important aspect of studies for design of rock excavations.

Jan 1, 1969

By E. V. Daveler, Frank L. Antisell

CERTAIN physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface, and the "set," or the decail appearance of the surface of the shape. The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are these characteristics connected that they are often used as synonymous terms by the refiner when he is speaking of well-refined copper. Oxygen is often spoken of as a medicine for copper, it being used to regulate the pitch.

Jan 1, 1920