Search Documents

By Borje Hjortzberg-Nordlund

THE great Swedish export iron ore mines are Kiruna and Malmberget in the north above the Arctic circle and Grängesberg in Central Sweden, see Figs. 1 to 3. These mines exported in 1951 about 13 million metric tons of high grade iron ore and concentrates. The origin of these three ore fields seems to be the same. They are of pre-Cambrian age and are regarded as typical instances of primary eruptive ore that has thrust up as glowing masses of lava flow between two somewhat older beds of porphyry. Apparently the ore and the porphyry became segregated from common parent magmas by a process of differentiation. Despite the fact that the Kiruna orebody belongs to the earliest pre-Cambrian formation, it has been influenced to an unusually small extent by later metamorphosisms, apart from its having been set on edge through folding and wrenching off by a number of later faults. The Kiruna ore occurs along a stretch of more than 4 miles as a series of slabs or lenses sloping steeply toward the east and sandwiched between two beds of porphyry. The main orebody has a length of about 3 miles and an average width of 300 ft with a maximum of 600 ft. The dip varies from 65° to 45° toward the east and the known depth is 3000 ft, although magnetic surveys indicate it may be at least 6000 ft. Malmberget has undergone a more thorough transformation, having been pressed and crumpled into a meandering band of disconnected layers and lenses. The largest of the more connected bodies of ore, the Great Ore Layer, outcrops on a low mountain ridge and has a total length of about 4 miles and a maximum width of about 300 ft. The dip varies from 30° to 70° towards the north. The main orebody in Grängesberg, the so-called

Jan 1, 1952

By C. B. Daellenbach, T. D. Tiemann

The prevention of quartz flotation by chelation of activating ions with the tetrasodium salt of EDTA in oleic acid flotation was investigated using a small vacuum flotation cell. It was found that flotation of quartz could be entirely suppressed in the presence of activating ions during complete flotation of hematite. It was further shown that the concentration of activating ions liberated from Wisconsin Gogebic taconite is sufficient to float quartz in an oleic acid system. Large tonnages of low grade siliceous iron ores occur on the iron ranges of the Lake Superior district. Although the lower grade nonmagnetic types are currently not of economic importance, they constitute a large future potential source of iron and steel, and hence have been the subject for extensive research on their beneficiation. TACONITES Of particular interest to the Dept. of Minerals and Metals Engineering at the University of Wisconsin have been the low grade nonmagnetic taconites of the Wisconsin Gogebic Range. These occur as five members of the iron formation and have been described in detail elsewhere.' Essentially they consist of an intimate mixture of hematite, goethite and quartz, with minor amounts of siderite, magnetite, iron containing silicates, and manganese minerals. A typical mean analysis based on the Bureau of Mines analyses' is: SiO2-52.50%, Fe2O3-43.40%, (Fe-30.38%), A12O3-1.15%, P2O5-0.07%, Mn2O3-0.29%, CaO-0.07%, (S-0.03%), Loss on ignition-2.00%. The quartz in these ores is of a microcrystalline variety,2 and so intimately associated with the iron oxide minerals that extremely fine grinding, in the order of minus 325 mesh, is required for liberation. During grinding and subsequent flotation, the concentration of quartz activating ions in the pulp becomes sufficiently high to activate quartz which floats along with the iron minerals in the presence of oleic acid. cook3 and co-workers concluded that oxidized iron ores released appreciable quantities of quartz-activating ions in water pulps. This is shown to be true in the present investigation. As a matter of fact, application of this phenomenon, as well as the intentional addition of activating calcium ions, is made use of in the an ionic flotation of silica from the iron oxide minerals.4,5 In view of the above, it becomes almost impossible to effect a sharp separation of quartz in the oleic acid flotation of the iron oxide minerals from these taconites, even with satisfactory liberation. This fact led to the current investigation to find a means of linking the activating ions with a chelating agent. The aim was to establish basic data for the quartz-water-oleic acid system which might not only be applicable to iron ores, but also to the flotation of other siliceous ores as well. EXPERIMENTAL METHODS Vacuum Flotation Cell: The vacuum flotation used in this investigation is similar to that used by previous investigators.6,7,8 The cell consisted of a 100 ml graduated cylinder with the lip removed. Vacuum from a water aspirator was applied to the cell through a trap; suitable tubing, and a rubber stopper inserted in the top of the cell. Constant absolute pressure was maintained by means of a manometer connected to the trap with a tee. Flotation: The required amount of activating ion solution was pipetted into a beaker. This was then diluted to 99.0 ml with water having a pH below that desired for the test, or so adjusted with HC1. After addition of 1.0 ml of oleic acid solution (2.0 mg oleic acid per ml), the pH was readjusted to the desired value with NaOH, and the entire solution transferred to the cell containing 1.5 gm of quartz. After vigorously agitating the cell and its contents for 2 min, the vacuum was applied to the cell and the estimated degree of flotation observed for a 3-min period. Activating ions studied included Ca++, Mg++, Al+++, and Fe+ + + added as chloride solutions. In addition,

Jan 1, 1964

By G. S. Hume

IN. THE autumn of 1922, British Petroleums Ltd. found oil of 14° Baumé in a sand 17 ft. thick in its. No. 2 well at Wainwright, 120 miles southeast of Edmonton. This greatly encouraged drilling in the Wainwright-Irma area and this past summer several wells were started, three of which are now completed and the others still being drilled. Of the three completed, No. 4 British Petroleums contains oil; No. 3 British Petroleums gave a show of oil but so far has not given much hope, of becoming a commercial producer; and No. 1 Maple Leaf Co., as now finished, is a. gas well with a daily flow of gas of about 2,500,000 cu. ft. at a closed pressure of 700 lb. An oil sand is reported to have been encountered below the producing gas horizon in the Maple Leaf well but has not been tested. Operations on this well have been suspended for the winter. The Geological Survey of Canada this past summer undertook a geological investigation of this area with the object of defining the structures with which the oil and gas are associated. The structure underlying this portion of the plains was supposed to be a terrace with the western edge dipping into the Alberta syncline and with a monoclinal structure to the east. By accurate leveling on known geological horizons on this terrace, a number of gentle folds were located and -it is in these folds that the oil and gas are found. At the British Petroleums Nos. 2 and 4 oil wells, the western flank of the fold has a gentle dip of only a few feet to the mile to the southwest whereas the strata on the eastern flank dip to the northeast about 40 ft. in ½ mile, the strike of the fold being northwest and southeast. How far oil will be found down the gentle southwest dip is unknown but probably the productive part of the fold will not exceed 1 mile in width, and possibly less. No. 3 British Petroleums well is on the strike of the fold 1 mile southeast of the two oil wells. The sand that was productive in Nos. 2 and 4 wells was not present in this well or, if present, was very thin and unproductive. Two other sand horizons, however, were encountered. The upper of these

Jan 3, 1925

By L. H. Duschak

Electrolytic zinc produced from sulfate solution and with pure lead anodes is always contaminated with a small and varying percentage of lead. The purpose of this investigation is to determine the characteristics of several lead alloys and their influence on the products of electrolysis and power consumption. The study of alloyed anodes has been a matter of interest for some years. Tainton, Taylor and Ehrlinger prepared a highly interesting paper' on this subject a year ago, in which the effects of silver-lead and some ternary alloys of lead-silver-tin were described, and the presentation of any paper on insoluble anodes will owe much to the inspirational results achieved by Dr. Colin G. Fink and Li Chi Pan in their work on insoluble anodes for the electrolysis of brine,2 and to other published papers by Dr. Fink and his coworkers embracing the development of the copper-silicon-manganese anode for the production of electrolytic copper and the general subject of anode development. The present paper describes a study of various combinations of 10 metals. The general plan of the work provides for the fabrication of the alloyed anode, its adequate conditioning by preparatory electrolytic operation, the production of cathode zinc and its analysis, the determination of the anode polarization, and other features. A list of the anodes tested, showing composition and polarization at various current densities together with the lead assay of the cathode zinc, is shown in Table 1. Determination of Anode Polarization In the determination of anode polarization under operating conditions it is essential that the anode area used be restricted to the side facing the cathode, in order that these measurements may be referred to a definite current per unit of area. It becomes necessary, therefore, to insulate the inactive face of the anode, to prevent the leakage of lines of force

Jan 1, 1930

By George F. Sowers

THE geophysical methods of exploration employed so extensively in mining and petroleum investigations are now being used in civil engineering. Requirements differ from those of mineral ex- ploration and therefore modified techniques have been developed. The civil engineer is primarily interested in the uppermost soil and rock strata. In highway engineering the materials affecting design and construction may be found within 15 or 20 ft of ground surface, and data on soils and rocks is seldom needed for more than a depth of 100 ft even for the heaviest structures.

Jan 1, 1954

By Craig S. Hartley

Expressions are obtained for the energy changes associated with the reaction of (a& (111) slip dislocations on intersecting (110)planes in anisotropic bcc metals. An energy criterion for assessing the likelihood of dissociation of the products of such reactions is also presented. It is found that the "burrier reactions" which form a(100) dislocations at the intersection of two active {110) slip planes are more energetically favorable in metals which exhibit a high value of Zener's anisotropy factor, A, than those which have a low value. The results are presented in a form which permits the stacking fault energy to be obtained from a measurement of the separation between par-tials in a dissociated configuration. However, until accurate calculations or measurements of the stacking fault energies involved are available, it is not possible to assess the physical importance of dissociated dislocations. In a recent paper,' the energy changes associated with several types of reactions between two slip dislocations, (a/2)(111){110), in bcc structures were calculated.* Isotropic elasticity and the approxima- tion v = -3- were employed. The purpose of this work is to present calculations of the energy changes for many of the same reactions using anisotropic elasticity. The problem of dissociation of a(100) and a(110) dislocations is also considered, and maximum fault energies for which dissociation will be energetically favorable are calculated for several bcc metals. Two general types of reactions are considered; those for which the reactant (a/2)(111) dislocations have long-range attractive forces and those for which the reverse is true. An example of the former is: (a/2)[lll] + (a/2)[lll]-a[l00] while the latter are typified by: (a/2)[lll] + (a/2)[111] -a[011] Only reactants lying in different slip planes are considered; therefore, the products must lie along (111) or (100) directions, which are the intersection of two {llO} planes. It will be assumed that the reactants and products are infinitely long parallel dislocations, since in this case the energy change associated with the reactions is a maximum.' THEORY The self-energy per unit length of a straight mixed dislocation in an anisotropic medium can be written? where b is the Burgers vector, K is an appropriate combination of the single-crystal elastic constants, and R and ro are, respectively, outer and inner cut-off radii of the elastic solution. The energy given by Eq. [I] does not account for any variation of the core energy with orientation. This could be manifested by an orientation dependence of the core radius or, equivalently, the Peierls width, of the dislocation. However, the energy contribution due to this source is expected to be small, and current models of the dislocation core are not sufficiently accurate to justify such a refinement. It has already been shown that for the isotropic case the energy contributions due to nonzero tractions across the cores of the reactants and products exactly cancel one another in the reaction.' Accordingly, it will be assumed that this contribution to the total energy change in the anisotropic case is small. In the subsequent discussion it is also assumed that the core radii of the reactant and product dislocation are the same and that, where stacking faults are formed, the faulted region is bounded by the centers of the partials. Consequently only changes in elastic energy due to the reactions will be considered. When the dislocation is parallel to either the (111) or the (100) directions, K may be written:375 K = (Ke sin2 a + Ks cos2 a) [2] where K, and Ks are the combination of elastic constants corresponding to an edge and screw dislocation lying along the same direction as the mixed dislocation, and a is the angle between the direction tangent to the dislocation line and the Burgers vector. Eq. [2] should not be confused with the isotropic approximation to the variation in energy with line Orientation.6 It should be noted that the essentially isotropic expression for K is a result of the characteristic symmetry of the (111) and (100) directions and is not, in general, valid for other dislocation directions in anisotropic cubic metals. The energy* change for a reaction in which the re- actant and product dislocations are parallel perfect dislocations can be written: where Ep and E, refer to the self-energies of the products and reactants, respectively. For dislocations parallel to (100) and (111) directions, Eq. [3] becomes:

Jan 1, 1969

By George W. Lower, William A. Hockings, Donald A. Kaczynski

The rate of dissolution of polycrystalline metallic copper in aqueous cupric ammonium nitrate solutions in the non-film-forming region was investigated by the rotating disc method. The investigation was performed in solution concentration ranges applicable to hydrometallurgical processes. This investigation was an extension of a study on the cupric ammonium carbonate system previously reported by Smith, Lower and Hockings, in which the following kinetic model was proposed: (1) Diffusion of cupric ammine ions to the copper surface; (2) Forward reaction - first order reaction of cupric ammine ions with metallic copper; (3) Reverse reaction - disproportionation of cuprous ammine ions to metallic copper and cupric ammine ions ; and (4) Diffusion of cuprous ammine ions from the copper surface. The nitrate system was selected for this study because it simplified the determination of the ionic composition of the solutions. The variables studied were stirring speed and cupric, ammonia, and nitrate concentrations. The dissolution rate increased linearly with at low values of but exhibited increasingly negative deviations from linearity at higher values of m. The rate also increased with increasing cupric concentration but decreased with increasing ammonia and nitrate concentration. Good agreement was obtained between the experimental rate data and the proposed model. Further verification of the model was indicated by the close agreement of the diffusion coefficient calculated from the data and comparable literature values.

Jan 1, 1974

By T. W. Guy

DURING recent years, tremendous strides have been made in the economical use of coal. This has resulted in, and to some extent has been a result of, making the fuel specifications more and more rigid. For this reason, all producers have found it necessary to improve their preparation materially, both as to sizing and the elimination of impurities, either by more effective preparation underground or at the tipple and cleaning plant, or both. This cause and its effect in all producing fields seem likely to continue for several years-at least. The splendid inherent qualities of the Pocahontas and New River coals are known all over the world, but their good reputation is only partly due to inherent qualities, and to natural conditions which generally favor loading coal comparatively free from impurities; it is due in large measure to the care and skill used, either with or without the aid of mechanical devices, to ship products consistently low in ash. The first coal from the West Virginia smokeless fields was mined and shipped near Quinnimont, on New River, in 1871, while the first shipments from the Pocahontas field were in 1883. The development of both fields progressed rapidly. At first activities followed the main lines of the Chesapeake & Ohio and Norfolk & Western railroads, and were extended later as branch lines were built from these roads. The Virginian R. R., about 1907, opened up the Winding Gulf territory, which has since become a large producer of smokeless coals from the Pocahontas and the New River measures.

Jan 1, 1931

By B. J. Kochanowsky

To improve blasting methods it is necessary to know how the explosive force acts and how rock resists this force. Because of the tremendous power developed within milliseconds and the great number of other factors directly affecting the technical and economic results, an analysis of the fundamentals of blasting theory is difficult. But since the rules used for layout design and for calculations of size of explosive charges are based on theoretical assumptions, complete knowledge of blasting theory has great practical importance in mining. Analysis of Blasting Theory: It is interesting to note the opinion of blasting experts with respect to contemporary blasting theories. F. Stussi,' Professor of the University of Zurich, stated: "We do not have enough experience yet to change our army engineering regulations in blasting and base it on new fundamentals. It is our duty to collect more practical data and to do more research in blasting to close this gap." K. H. Fraenkel,' editor of the Manual on Rock Blasting published in 1953 in Sweden and written by well-known Swedish, German, Swiss, and French blasting and explosive experts, said: "To the best of our knowledge no suitable formulas for civil blasting work are to be found in the American, French or German literature."

Sep 1, 1955

By R. J. Wensley

The use of small substations for the supplying of 275-volt energy to the locomotive and cutting machines in coal mines is a well-established practice. A few years ago, when labor costs were lower, these substations were located as near to the load as possible, and an operator was provided for each station. This practice has now become so expensive that substations are being located with reference to other mining machinery, such as hoists or pumps, so that one operator can look after both. Sometimes the substation is operated by one whose duties make him traverse quite a large area. In such cases the interruption of alternating-current supply may produce a long interruption in the direct current, as the station cannot resume service until this man reaches it. Such interruptions interfere seriously with production and may easily counterbalance the supposed saving gained by such operating methods. The grouping of substations for convenience in operating may also result in excessive copper loss and consequently poor trolley voltage, with its attendant evils of low locomotive speeds and increased locomotive motor maintenance. The speed of the coal-cutting machines will also be reduced. By relieving the substation of its burden of the operating labor cost, the most economical location, from an electrical standpoint, may be chosen. The matter of machine insurance should also be considered. If an attendant is caring for several kinds of equipment, he cannot watch the machine continually for signs of trouble; therefore, continued overload, phase failure, low alternating-current voltage, bearing trouble, etc. may result. Some partly automatic equipments have been installed; these have protection against low voltage, reverse current, and bearing trouble and are provided with automatic reclosing circuit breakers. This is a step in the right direction but it does not go far enough to give first-class machine insurance. The saving in maintenance costs is often the smallest item, when considering the automatic substation as machine insurance. When the coils in a machine are roasted out, due to continued overload or to opera-

Jan 1, 1922

By John Birkinbine

An unusually large number of crystals of magnetite obtained in the exploitation of a deposit of magnetic iron-ore of remarkable purity, encouraged the preparation of this paper, and its presentation at this time, that the matter might go on record in the Transactions. To make this record more complete, a preliminary statement is offered concerning the district and locality in which the ore is found. To the northeastern portion of the State of New York the United States is indebted for a large percentage of the iron-ore which has assisted in developing the resources and industries of the nation. As early as 1804, iron-ore was mined between Lake Champlain and the Adirondack mountains, and this district has since been an important and continuous contributor to our iron-ore supply. The production of the Lake Champlain district for the last, eleven years is as follows: Years. Gross tons. 1879,...........420,341 1880,...........531,000 1881,...........637,000 1882,...........675,000 1883,...........500,000 1884,...........504,894 1885,...........379,077 1886,...........588,752 1887,...........768,852 1888,...........789,419 1889,...........750,230 Approximate total,.....6,644,565

Jan 1, 1890

By Constantine Michalopoulos, Roger C. Van Tassel

Commercial demand for gold in the United States is important. It has a large impact on the total world commercial and overall non-monetary demand. Given the present free market price and our need to import gold, it has a substantial adverse effect upon our international payments position. But, according to most recent estimates, the United States demand is perhaps no more than 20% of the world as a whole. In 1971, United States consumption was estimated at 215.6 tons out of a total of 1,412.1 tons 1. This figure is very close to the 16% figure developed by Consolidated Gold Fields as the average for the years 1968-1970.2 Surveys of both production and use of gold on a world-wide basis are not new. With the bulk of gold production in only a few countries, it has been possible to develop fairly reliable series on gold output. Estimates have been developed on the known reserves of gold and probable output at various prices.3 On the demand side, figures have been somewhat less complete and reliable. The Bank for International Settlements and the Director of the United States Mint have regularly published estimates of commercial use in major industrial countries. The IMF has issued an increasingly comprehensive survey in its Annual Reports. The IMF has attempted to cover all nations-not restricting its efforts to major industrial nations-and has tried to estimate both gold taken for commercial uses (Estimated Industrial and Artistic Use) and for private hoarding. Their method is to begin with data on free world output plus any net sales by the Soviet Union, subtract any additions to world monetary stocks (or add to available supply for any net reductions in world monetary stocks), subtract estimates for commercial demand and have left as a residual an estimate for private hoarding. The method is straightforward and simple but the quality of the data is suspect. Industry sources tend to believe the figures as biased on the low side because of a persistent tendency to underreport gold movements.4

Jan 3, 1974

By K. E. Merklin, F. D. DeVaney

Students of the modern blast furnace seem unanimously agreed that they are observing a major revolution in practice. Rather than changing construction and operation of the furnaces, most of the great advances now under way deal with the raw materials feed. Prepared burdens have gained increasing significance during recent years. Sizing, concentration, and agglomeration have all become bywords to greater production and reduced operating costs. The remarkable results with test furnaces in which self-fluxing sinter makes up part or all of the ore charge foretell even greater improvements. Other investigators have reported many of these advances, and it is enough to predict here that more and more operators will turn to the use of self-fluxing sinter.

Jan 3, 1960

By S. R. Mitchell, M. C. Fuerstenau, A. M. Gaudin

The two principal attributes of a thickener pulp are its settling rate and the ultimate pulp density of the thickened mud. Testing for evaluation of thickening attributes of a pulp has usually been done batch-wise by placing the pulp in a one-liter glass graduated cylinder and noting the position of the boundary between clear liquor and mud as a function of time. Refinements in testing have included repulping a thickened mud to various dilutions and evaluating the settling rate on these various repulped muds. This is considered to make possible an estimate of the settling rate as a function of pulp density and therefore to pinpoint the slowest settling pulp which ought to be critical from the standpoint of thickener plant design. Finally, tests are sometimes made with model-size continuous thickeners of arbitrary size. In batch tests it is generally accepted that the behavior of a pulp is described by a curve such as the one shown in Fig. 1, in which the position of the boundary between clear liquor and mud (the mudline) is plotted against time. It has also been assumed that the initial settling rate (the slope of the line segment AB) is descriptive of the pulp and independent of the size and shape of the container. Where the settling rate is slower and clearly a function of time (portion CD of the settling curve), it has been assumed that the data are not of much use because of the intrusion of compacting phenomena. The next important datum is the height, PE, which is a measure of the so-called ultimate pulp density. This quantity is assumed to be characteristic of the pulp and independent of the container.

Jan 6, 1959

By A. E. Harnsberger

IT is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practi-cally every refinery operation, from the charging of crude oil to a dis-tillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from -50° F. to 900° F. Pressure may vary from subatmospheric to 2000 lb. per sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature "may be divided into three parts: (1) extremely low temperatures of the order of -50° F.; (2) temperatures at atmospheric or slightly above; (3) temperatures from 200° to 900° F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250° F. The second type of corrosion occurs in high-temperature pump-ing equipment, with temperatures from 450° to 900° F., largely caused by sulfur compounds. There are also other corrosive conditions met with

Jan 1, 1935

By H. C. Burghard, F. R. Brotzen

Experiments were performed to determine the effects of mechanical vibrations on ordering in CuAu. The effects of 5, 10, and 15 kc vibrations were investigated over a range of ordering temperatures of 280° to 360°C. A decrease in the rate of ordering was observed at all frequencies and ordering temperatures. THE effects of mechanical vibrations on certain solid-state reactions have been noted by several investigators. In 1930, Mahoux' reported a substantial increase in the case depth of a steel sample nitrided under the influence of mechanical vibrations over that of an unvibrated sample. Similarly, an accelerating effect of vibrations on the diffusion of chromium in steel was noted. Guillet, in the same year, confirmed the results of Mahoux. More recently Schenck and schmidtmann3 studied the effects of low-frequency, alternating loads on the diffusion of carbon in steel. The results of their experiments, conducted at 500 cycles per min and large strain, (0.2 pct), indicated an acceleration of the process. These workers also reported an increase in case depth of a sample vibrated at 430 kc during a carburizing treatment. Effects of high-frequency vibrations on solid-state reactions have also been investigated by Gudzoff and Gavze6 and Fairbanks and Dewez.7 The former reported an acceleration of the age-hardening process in aluminum alloys. The latter noted changes in the structure and mechanical properties of steel annealed under the influence of vibrations. On the other hand, Altenburg4 and Ehringer5 have given some theoretical reasons and experimental evidence as to the improbability of any effect of vibrations on diffusion. Comprehensive surveys of the effects of vibrations on metallurgical reactions are given by Hiedemann' and Bergmann.9 None of the above investigations led to a physical description of the effects of mechanical vibrations on solid-state reactions. In the present study an attempt was made to gain an understanding of the influence of vibrations on nucleation and diffusion. The order-disorder transformation was chosen for investigation since its mechanism has been extensively discussed in the literature. Moreover, the progress of the transformation may be easily followed by observation of electrical resistance changes. EXPERIMENTAL PROCEDURE The specimens used for the experimental observation of ordering rates were prepared from 50 at. pct Cu-Au alloy wire.* Each specimen consisted of a 0.02-in. diam wire approximately 10 in. long to which two copper potential leads were silver soldered, 2 1/2 in. apart, near one end of the wire. A 1/8-in. diam by 1/4-in. long steel stub was silver soldered

Jan 1, 1960

By L. Sturkey

Quantitative X-ray diffraction studies of the precipitation of thorium in a Mg + 3.3 Th + 0.51 Zr alloy (HK31A) in both the as-cast and cold-worked states show that the precipitation may be described by f = 1 - e(t/T)1/2 over most of the aging period. The effects of cold work and temperature changes are determined. The precipitation of tile equilibrium Mg-Th compotund is Preceded by the formation of a transition phase of higher thorium content, with the cowposition Mg2Th and with a Laves-phase structure. Thorium-containing alloys of magnesium have assumed considerable commercial importance, especially for applications requiring exposures to temperatures greater than 500°F for appreciable lengths of time. The principal commercial wrought alloys in this system are HK31A, containing nominally 3 pet by weight thorium and about 0.7 pet by weight zirconium: and HM21A. containing 2 pet by weight thorium and 1 pet by weight manganese. These two alloys retain a high level of properties even after exposures of 100 hr at 600°F, while the more common alloys containing aluminum and zinc are badly overaged by these conditions. Therefore, in order to obtain some insight into the mechanism by which thorium produces high temperature stability in these wrought alloys, it seems desirable to investi- gate the effect of temperature and mechanical working on the precipitation processes involving thorium. Since the scattering power of a thorium atom for CuKa X-ray radiation is about ten times that for a magnesium atom, the magnesium alloys containing about 3 pet by weight thorium are ideal for quantitative measurements by X-ray diffraction of the amount of Mg-Th compound present at any time. Such quantitative measurements should be of theoretical importance in the study of the effects of time, temperature, and deformation on precipitation and precipitation hardening. Of the two commercial alloys, HM21A and HK31A, the latter is certainly the most suitable for study: In the Mg-Th-Zr2 system, only Mg-Th compounds need be considered, since no ternary compounds or binary Th-Zr3 and Mg-Zr4 compounds exist. The Zr is added to this alloy as a grain refining agent and probably plays a secondary role in precipitation. On the other hand. thorium and manganese form many

Jan 1, 1961

By Howard L. Hartman, Burke O. Trafton

There is a fruitful area of computer competence which has gone virtually unnoticed by the mining industry. This is in the solution of its numerous fluid-flow distribution problems, involving the circulation of air, water and other fluids in conduits through mines. Typical of these is the mine ventilation system, which circulates air through mine openings to the working faces. The networks of interconnected airways in large mines-often resembling a tortuous maze or labyrinth defying representation by schematic, let alone solution-must somehow be resolved and analyzed, if effective and safe control of the ventilation is to be maintained. These are admirably suited to programming for solution by high-speed electronic computer. Not only can direction of flow be determined but quantity and head loss as well. EARLIER EFFORTS AT NETWORK SOLUTION The only prior attempt to solve mine ventilation networks by digital computer methods was made by a Japanese investigator1 in 1958 whose work went unpublished. Unfortunately, he employed a method of network analysis little used in the United States and one which could accommodate a maximum of only 30 airways. While his analysis seems unnecessarily cumbersome and involved, it did suggest that a digital computer approach was feasible.

Jan 9, 1963

By F. R. Morral

In 1964, mining education in the United States will celebrate a 100th anniversary-that of the founding of our first school of mines at Columbia University. Prior to that, curricula leading to degrees in mining and metallurgical engineering were offered in 1853 by the Polytechnic College of Pennsylvania in Philadelphia. But the New World's earliest achievements in mining and metallurgical education were those of the Spanish in what is now Mexico. American metallurgy probably goes back to Father Jose de Acosta, who in 1590 described the metallurgy of silver and mercury in the New World.' The Spanish priest and metallurgist Don Alvaro Alonso Barba Toscano (1569-1662), in his hook The Art of Metals, published in 1640, stated a need for a school of mining and metallurgical education in the New World. (The latest translation of this book was made by R. E. Douglas and E. P. Mathewson and published by J. Wiley & Sons, New York, in 1923.)

Jan 1, 1963

By W. C. Bednar

In all, 127 producing oil wells, 8 producing gas wells and 212 dry holes were drilled during 1936 in the Central Texas area; 76 wells in Bexar County, 62 in Caldwell County, 44 in Guadalupe County, 22 in Williamson County, 20 in Navarro County and 20 in Frio County. Less than 20 were drilled in each of the other counties and none at all in Ellis, Hill, Bosque, Coryell, Lampasas, Burnet, Llano, Kennedy, Mason, Real, Kinney and Uvalde Counties. The Pearsall-Austin chalk field in Frio County and the Zoboroski field in Guadalupe County were the only new discoveries and there were no important extensions to old fields. In this report Corsicana, Mildred (Elm Ridge), Angus-Edens-Hodge, Burke, and Rice-Oil Ridge, all shallow Navarro County stripper fields, are grouped together under the name of Corsicana. This grouping follows that of the Railroad Commission of Texas, thus facilitating the gathering of production data. A map showing the location of the oil and gas fields in the Central Texas Area was published in Volume 114 of the A.I.M.E. TranBactions, page 380. New Fields Pearsall-Austin Chalk.—The Amerada Petroleum Corporation completed 13 Austin chalk wells during 1936 on the large Amerada-Rycade block in Frio County. Other companies drilled two dry holes to the Austin chalk in this vicinity. Not enough wells were drilled to give control of the structure but it appears to be a nose plunging in a west-southwest direction. A second deep test is being drilled in the Pearsall area and at this writing has cemented off a show of oil and gas in the Edwards limestone. The Humble Oil and Refining Co. is building a 6-in. pipe line from Lytle, Tex., to serve the Pearsall field. Zoboroski.—Actual discovery of the Zoboroski field was made by W. J. Walton et al. in 1931. The discovery well, Anton Zoboroski No. 1, was a small producer making but from 3 to 5 bbl. per day, which was used locally for fuel oil. The discovery of the Darst Creek Extension in

Jan 1, 1937