Search Documents

By Jack A. Kanz, Samuel R. Shortes, E. C. Wurst

Zinc diffusion into GaAs from the vapor phase through reactively sputtered SiO, films Izas been inrestigated for various zinc pressures at 1000"C. Diffusions were carried out in evacuated quartz ampules with elemental zinc and with various Zn-Ga alloys. Sputtered films have proved effective in lowering surface concentrations and preventing surface deterioration during diffusion. Approxin.ate complenzentary error-function impurity distributions were found when surface concentrations were reduced to approximately 3 -—4 x 10" atoms cm'3 or less with dilute zinc sources or by diffusion through SiO, films. Zinc difhsions in GaAs tlzrough SiO, films produced more planar diffusion fronts than were observed with uncoated zuafers under identical conditions. A) Surface Deterioration During Diffusion. Device technolorn-- in compound semiconductors has been hampered by several difficult problems not normally encountered with silicon and germanium. 111-V and 11-VI compound semiconductors generally have volatile constituents at temperatures used for diffusion. To achieve specific junction depths in reasonable lengths of time, or to obtain particular impurity distributions and doping levels, it is often necessary to use temperatures which cause surface deterioration and erosion of the wafer. The resultant surfaces are generally unsuitable for devices. The type and extent of surface damage depends to varying degrees on the particular environment of diffusion and on the particular impurity in question. The most common type of deterioration results from simple dissociation of the gallium and the arsenic during diffusin.' The deterioration process is significantly enhanced by thermal gradients in the diffusion zone, usually resulting in vapor transport and condensation at the cooler portion of the system. The resulting damage sometimes appears as a general haziness over the surface or an array of pyramidal etch pits characteristic of the particular orientation. Occasionally, erosion of the surface occurs uniformly over the wafer so that surface loss is not readily apparent. Workers in GaAs usually resort to the sealed-ampule type of diffusion system3"5 rather than the more conventional open system used for silicon and germanium. Another type of deterioration results from direct interaction of the impurity with the surface. The form of deterioration may vary from surface alloying, as in the case of zinc, to direct chemical attack and vapor transport of the reaction products, as in the case of sulfur. Surface alloying with zinc occurs at higher temperatures and source vapor pressures.4 The process is largely controlled by the amount of free gallium on the surface of the wafer in equilibrium with the arsenic lost to the system. The group-VI elements, sulfur, selenium, and tellurium, are commonly used donor impurities for gallium arsenide. These elements are characterized by high vapor pressures and high chemical

Jan 1, 1964

By R. J. Borg, C. E. Birchenall

Vapor pressures of eight compositions of Mg-Cd have been determined by the Knudsen effusion technique. Measurements are made at several temperatures for each alloy and the results interpolated to a common temperature for the calculation of the activities. It is not possible to obtain values for the partial molar enthalpies because of the narrow temperature range spanned by the measurements. The results show less precision than those obtained for pure Cd which are also reborted. These alloys are extremely susceptible to corrosion which provides a possible explanation for the lack of precision. Nevertheless, the values of the activity are in good agreement with the results of electromotive force measurements previously reported for the Mg-Cd system. MAGNESIUM and cadmium are mutually soluble in all proportions in the solid state and form a single phase which has the hexagonal close-packed structure. X-ray investigations of this system1,2 have revealed a rapid variation in the relative dimensions of the unit cell occurring at approximately 50 at. pct. The rate of change of the c/a ratio with composition increases markedly for alloys containing more than 50 at. pct Cd. The purpose of this investigation was to determine the activity of Cd in the neighborhood of 50 at. pct and to discover whether or not the thermo-dynamic properties undergo a similar rapid change. The activities are calculated from vapor pressure data obtained by the Knudsen effusion method. Unfortunately the precision of the data from which the thermodynamic values are calculated is insufficient to establish unequivocally a departure from the normal trend. The results are reported primarily because they substantiate the only previously reported activity measurements3 and because they include values for pure Cd which in contrast to those of the alloys show excellent precision. The Cd-Mg system is known to contain several ordered phases. However, this investigation was made at temperatures considerably above the transition temperatures, and the alloys may be regarded as nearly random solid solutions. EXPERIMENTAL Apparatus—The effusion cells are machined from solid tantalum rod. The lids consist of threaded, flanged rings of tantalum onto which are welded shallow cups of 4 mil molybdenum foil. The orifice, which is located at its center, is made by grinding off a small dimple produced with a sharpened punch. Such an orifice has been mounted in plastic, sectioned, and the thickness of the orifice edge measured in a microscope. The maximum thickness is 0.00016 in., and the Clausing factor is consequently equated to unity. The area of the orifice is determined by tracing its projection on the screen of the metallograph at a known magnification and measuring the area of the tracing with a planimeter. Excellent temperature control is achieved with a 4 by 18-in. alundum core, gradient-wound, furnace

Jan 1, 1960

By Francis Donaldson

THE direct injection of cement grout into water-bearing fissures as a means of checking or stopping the flow of water into shafts and tunnels has been experimented with for a decade or longer and seems to have been first attempted in Europe. The earliest application of which the writer has found a record was at a shaft sunk by the Mining Society of Lens; this is described by C. Dinoire in the Transactions of the Institution of Mining Engineers.1. It is only lately, however, that the process has been entirely successful. This success has been accomplished on the Catskill Aqueduct, now under construction by the city of New York. This aqueduct includes a number of deep pressure tunnels, reached by shafts for both waterway and construction purposes. In portions of these shafts and tunnels considerable underground water was met. The contract for the first of these deep pressure tunnels was let to the T. A. Gillespie Co.; this section is known as the Rondout Siphon. It leads under the Rondout valley at a depth of from 400 to 800 ft. and is about 5 miles long. The engineers expected that considerable water would be encountered, but fortunately this was not the case except at one shaft, known as No. 4, which penetrated the rock at a junction between limestone and conglomerate. Water-bearing fissures were encountered almost immediately. At a depth of about 200 ft. a flow of 1,500 gal. per minute was struck. The shaft then contained as many pumps as could be used, and it seemed impossible to sink it further. After vain efforts had been made to proceed, John P. Hogan, a division engineer of the Board of Water Supply, suggested that cementation of the fissures be tried. The process was attempted for the first time in this country. Since the shaft was partly full of water it was necessary to drill grout holes with a diamond drill. Platforms were placed on the timbers at the water level, the diamond drill was installed and six 90-ft. holes were drilled in the bottom of the shaft. Several car loads of cement were pumped through these holes into the fissures, the drill casings being used for grout pipes. This largely cut off the flow of water from the bottom and sinking could then

Jan 1, 1914

By Francis Donaldson

The direct injection of cement grout into water-bearing fissures as a means of checking or stopping the flow of water into shafts and tunnels has been experimented with for a decade or longer and seems to have been first attempted in Europe. The earliest application of which the writer has found a record was at a shaft sunk by the Mining Society of Lens; this is described by C. Dinoire in the Transactions of the Institution of Mining Engineers.1 It is only lately, however, that the process has been entirely successful. This success has been accomplished on the Catskill Aqueduct, now under construction by the city of New York. This aqueduct includes a number of deep pressure tunnels, reached by shafts for both waterway and construction purposes. In portions of these shafts and tunnels considerable underground water was met. The contract for the first of these deep pressure tunnels was let to the T. A. Gillespie Co.; this section is known as the Rondout Siphon. It leads under the Rondout valley at a depth of from 400 to 800 ft. and is about 5 miles long. The engineers expected that considerable water would be encountered, but fortunately this was not the case except at one shaft, known as No. 4, which penetrated the rock at a junction between limestone and conglomerate. Water-bearing fissures were encountered almost immediately. At a depth of about 200 ft. a flow of 1,500 gal. per minute was struck. The. shaft then contained as many pumps as could be used, and it seemed impossible to sink it further. After vain efforts had been made to proceed, John P. Hogan, a division engineer of the Board of Water Supply, suggested that cementation of the fissures be tried. The process was attempted for the first time in this country. Since the shaft was partly full of water it was necessary to drill grout holes with a diamond drill. Platforms were placed on the timbers at the water level, the diamond drill was installed and six 90-ft. holes were drilled in the bottom of the shaft. Several car loads of cement were pumped through these holes into the fissures, the drill casings being used for grout pipes. This largely cut off the flow of water from, the bottom and sinking could then

Jan 1, 1915

By T. Glen Heslop, Dennis H. Laubscher

INTRODUCTION In all cave mining operations waste is drawn mixed in the ore, hauled, hoisted and milled. This waste usually contains some mineral which partly covers some of the costs of mining and milling it, but it still re- presents a loss of profits as the production rate from the mine is matched to the mill capacity - every tonne of waste milled replaces a tonne of profitable ore. Draw control aims to reduce the amount of waste drawn and to increase the amount of ore recovered. It is also used to regulate the grade of ore flowing to the mill and in block cave blocks to prevent potential stress build- up on the major apexes above grizzly drifts. This paper summarises what has been learnt about draw control in the forty years that cave mining methods have been used in the three largest underground chrysotile asbestos mines in the southern hemisphere. The four mining methods to which draw control has been applied are: a. Block caving. b. Shrinkage with overburden caving. c. Sublevel caving. d. Open stoping. Open stoping has been included because on a number of occasions severe falls from the back and side of these open stopes have occurred. Without full records of where and when ore is blasted, when and how much ore has been drawn from each of the drawpoints, it would be impossible to analyse the migration of ore and fallen waste in the stope. Several problems peculiar to chrysotile asbestos ore bodies affect the practice of draw control. Heterogeneous fragmentation, cavities, side pressures and the interaction of stresses in the caved ore affect the migration of ore under draw. Fibre is normally not developed uniformly throughout the ore bodies, values vary from place to place but there is usually a general decrease upwards and the hangingwall contact is an economic limit. The immediate hangingwall rock frequently looks like the ore body hostrock and is difficult to recognise in a drawpoint, and cannot be used as the marker for stopping draw. During caving or shrinkage, a large proportion of fibre becomes detached from the host rock and re- ports in the fines, which migrate differently to the larger rocks. The fines are not sticky, and flow easily if loose and dry, but compacted, the fibre and rock fines con- solidate the ore. During draw the proportion of fines in the ore varies considerably, as fines either flow relatively freely between the large rocks or become trapped and compacted above large rocks or hangups. This creates a large sampling error in drawpoint grade assessments, whether done visually or by bulk sampling, unless the assessments are done frequently. The method of draw control used is to regulate the draw rate in an attempt to lower the ore-waste interface as evenly as possible, and to finally stop working the drawpoint when a calculated tonnage has been drawn.

Jan 1, 1981

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

By J. T. Burwell

The crystal orientation in silicon iron that has been given a particular treatment described by Goss,l has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualitative. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200. It is now generally agreed that Goss's original conclusion1 that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom. X-ray Data A strip of the material containing 3.1 per cent Si, prepared by Goss,† 1.2 by 0.0125 in., was etched rapidly in warm dilute hydrochloric acid until it was 0.005 in. thick, in order to eliminate the effect of the two surface layers. The specimen was then mounted in an integrating camera similar to one described in the literature.4 The purpose of this camera is to translate the specimen during exposure, so that a statistically large number of grains contribute to the pattern photographed. The camera also allows the plane of the specimen to make various angles with the X-ray beam. An area 5 by 1.2 in. was scanned by a beam of unfiltered radiation from a molybdenum target tube operating at 37 kv., and the measurements were made principally on the peak of the white radiation. X-ray photographs were taken at intervals of 15" in a plane

Jan 1, 1940

By J. T. Burwell

The crystal orientation in silicon iron that has been given a particular treatment described by Goss,l has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualitative. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200. It is now generally agreed that Goss's original conclusion1 that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom. X-ray Data A strip of the material containing 3.1 per cent Si, prepared by Goss,† 1.2 by 0.0125 in., was etched rapidly in warm dilute hydrochloric acid until it was 0.005 in. thick, in order to eliminate the effect of the two surface layers. The specimen was then mounted in an integrating camera similar to one described in the literature.4 The purpose of this camera is to translate the specimen during exposure, so that a statistically large number of grains contribute to the pattern photographed. The camera also allows the plane of the specimen to make various angles with the X-ray beam. An area 5 by 1.2 in. was scanned by a beam of unfiltered radiation from a molybdenum target tube operating at 37 kv., and the measurements were made principally on the peak of the white radiation. X-ray photographs were taken at intervals of 15" in a plane

Jan 1, 1940

By Chester T. Sims

RECENTLY, a new type of superalloy material called TD Nickel* has been marketed.' It is a sim- ple, two-phased alloy, consisting of thoria particles dispersed in nickel of rather high purity (Ni-2 pct Thoz). Its mechanical properties appear relatively superior to previous experimental material attempting to use the oxide nonmetallic dispersion concept (except SAP), and superior to conventional nickel-base alloys at high homologous temperatures. This is derived from an interesting method of creating the dispersion, arising during chemical processing of the nickel and thorium salts in solution while reducing the nickel to metal. An evaluation of the thoria phase was conducted at this laboratory. Material and Procedure. TD Nickel was made available, consisting of several inches of 0.470-in. rod, extruded at a ratio of 64: 1, straightened, and centerless ground. Property determinations on this rod by the supplier at 1800°F showed an ultimate tensile strength of 11,400 psi, yield strength of 9600 psi, and 6 pct elongation. Specimens were removed from the rod for as-extruded metallography, and two 1/2-in. lengths supported on high-purity Al2O9 bricks were placed in a laboratory muffle furnace for exposure at 2000° F. The furnace door was left cracked to allow a slight amount of circulation. One specimen was removed at 200 hr for examination; the other was left for 2000 hr. Metallography. The micro structures obtained for the three conditions of exposure are shown in Fig. 1. Elongation of the grain structure in the extrusion direction is readily evident. The grains appear to be up to 0.001 in. (0.003 cm) long, with a length/width ratio of about 10: 1. Allowing for modest local in-homogeneities in structure, no significant change in thoria particle size or nickel alloy grain size occurred during the 2000°F exposure. However, etching depth varies slightly from one specimen to another, changing the number of particles visible. The thoria dispersion appears to be in the order of 0.01 (min) to 0.5 (max) p diam. The minimum diameter is difficult to estimate at X10,000, and may be less. Interparticle spacing appears to be about 0.1 p. Etching effects can be seen, depending upon grain orientation. A cubic etch-pit pattern appears in certain grains, apparently when etching is started by an anodic particle of thoria, Fig. l(c). The cubic pattern appears related to crystallographic orientation, and is prominent when the [ l00 ] direction is perpendicular to the plane of polish. The grains which present a ridged appearance in the photograph appear to be oriented with the [110} direction perpendicular to the plane of polish. Analysis. The thoria particle size was measured by a line intercept method perpendicular to the extrusion direction. Only particle sizes measuring 0.001 in. at X10,000 or larger could be extimated. Within limits of experimental error, particle size distribution appears to be unaffected by exposure, Fig. 2. To check structural stability further, a grain-growth evaluation was made. The number of grain-boundary intersections was counted at X500 on each of several traces normal to the extrusion direction for each condition. It can be seen from Table I that grain diameter appears unchanged by the 2000°F exposure. The slightly finer grain diameter after 200 hr may be attributed to variations in grain size from area to area in the original extrusion. From the present rather limited study of Ni-2 Th on, it appears that: 1) for time-temperature exposure up to 2000 hr at 2000°F (Larsen-Miller parameter = 57, homologous temperature = 0.8) thoria particles of the size studied are highly thermally stable; they do not significantly react, agglomerate, or diffuse; and

Jan 1, 1963

The authors of T.P. 4179 have conducted a large number of experimental water floods, and the data are reported in a very clear manner. These data show significant variations of residual oil saturation with changes in wettability, interfacial tension, flooding rate, and oil-water viscosity ratio. Furthermore, some of the data obtained cover a range of variables not previously reported in the literature. It is our opinion that at least some of the observed variation in oil recovery can be obtained only in floods made under conditions identical with those used by the authors. There are other systems which may be said to have the same wettability, but which exhibit an entirely different qualitative dependence of oil recovery on the experimental variables. In this regard, we would like to direct attention to several items which we feel are not given sufficient consideration in the paper. The first of these items has to do with wetting equilibrium. A survey of the current literature will reveal that little is known, and even less is understood, about wetting equilibrium. This is particularly true of the relation between contact angle measurements made under static conditions, and the wettability existing under the dynamic conditions of floods carried out at relatively high rates. We feel that this is a very important consideration, particularly in the floods the authors performed under what they consider to be "water-wet" conditions. It is our opinion that wetting equilibrium did not exist in these floods, except possibly at the very lowest rates. This opinion is in part based on some flooding tests we have made which are very similar to some of those described by the authors. These floods were made in unconsolidated cores, 6 in. long and 13/4 in. in diameter, made up of carefully graded glass spheres of the approximate size of the sand grains used in the subject paper. The cores were mounted vertically, and distilled water was used to displace a refined oil equivalent to the authors Soltrol C. The glass spheres had previously been carefully cleaned so that they were strongly wet by the water. The floods were made with and without an interstitial water saturation. When interstitial water was present, the solid surfaces were mostly covered with water prior to injecting the flooding phase. Consequently, a condition very near wetting equilibrium existed throughout the flood. The data in Fig. A show that under these eircumstances, rate had no influence on residual oil at flood-out, over the range of rates studied. On the other hand, in the absence of interstitial water, the surfaces are all covered with oil before the displacement. To achieve wetting equilibrium the injected water must displace the oil from the surfaces themselves. This is not a fast process. Therefore, the effective dynamic wetting condition in floods of this type must depend upon the flooding rate. When the flood rate is very low, compared to the rate at which wetting equilibrium is attained, the residual oil saturation at flood-out is essentially the same as the residual obtained when interstitial water is present. This is shown in Fig. A, and occurs because the dynamic wetting conditions are the same in both cases. However, at moderately high flooding rates, the rate has an important bearing on the amount of oil recovered because in this case the attainment of surface equilibrium is the slow step. We believe that, in the absence of an interstitial water saturation, oil recovery varies with rate because of the reasonably slow approach to wetting equilibrium which occurs during the displacement. In fact, as the rate is increased, the oil recovery performance indicates the core is becoming progressively less water-wet. At the highest rate there is even considerable simultaneous production of oil and water after breakthrough. This does not occur at the lower flooding rates, nor is there appreciable simultaneous oil and water produc-

Jan 1, 1957

By H. W. Mead, C. E. Birchenall

SELF-DIFFUSION in pure gold has been studied by Sagrubsky,1 McKay,2 Gatos and coworkers,3,4 and Okkerse.5 Sagrubsky used a sectioning technique but reported results far lower than any of the others. The work seems to be carefully done, and it appears that a factor of 60 must have been omitted in his calculations or the units misstated by an equivalent amount. McKay used a surface activity method, and Gatos and Kurtz, following Gatos and Azzam, applied autoradiography to the measurement of activity on an oblique section through the diffusion zone. These two investigations agree well with each other but give results below those reported here. Okkerse employed a very careful sectioning technique. Chemical interdiffusion in Au-Ag alloys has been measured under several concentration conditions. Average values of the diffusion coefficient for the range of 0 to 18 atomic pct Au were obtained by Braune.6 since the diffusion coefficient probably varies markedly over this range, the values may not be too useful. Also, a plot of these data suggests that grain boundary contributions may have been appreciable at the lowest temperature employed. Ebert and Trommsdorf7 give average values for 0 to 9 atomic pct Ag, and Johnson8 reports average values for 45 to 55 atomic pct Au. Johnson also measured silver and gold self-diffusion coefficients in 49.2 atomic pct Au alloys, and self-diffusion in pure silver. The self-diffusion of gold in pure silver has been determined by Jaumot and Sawatsky.10 Other measurements which do not cover a range of temperature or are of low precision are not mentioned in this account since a review by Kubaschewski is available." This contribution reports diffusion coefficients for self-diffusion in gold, self-diffusion of gold in Au-Ag alloys, and chemical diffusion in Au-Ag alloys. Although it had been intended to obtain silver self-diffusion data in the alloys it now appears unlikely that these measurements can be done soon, so a table has been worked out for a self-consistent scheme of diffusion coefficients which should not be too far from the true values. Experimental Details Experiments on pure metals were conducted using fine gold of 99.99+ pct Au and silver of the same purity. Alloys were prepared by melting the two metals together in a graphite crucible in vacuo and allowing the slug to solidify in the crucible. After machining to a cylinder about 0.85 in. diam each slug formed one half of a diffusion couple. Compositions were determined later by analyzing chips taken from the extremities of the diffusion zones. The gold used in the preparation of alloys was sometimes pure gold but was normally either in the form of clean pickled alloy from previous experiments or gold recovered by oxalic acid precipitation from warm aqueous solution. Chips from the various stages of experimentation were dissolved in aqua regia and the solution taken to low bulk, diluted with water, and again taken to low bulk before diluting for the precipitation. This precipitated gold contained a small amount of silver as the only impurity detectable by spectrographic analysis. Disks for use in diffusion couples had opposite plane faces abraded on emery paper as far as zero grit, were annealed for 12 hr at 900°C in argon, and had one face of each disk polished to 000 emery paper. Radioactive gold was plated at about 2 ma per sq cm from a small volume of cyanide solution containing 1 mg of inactive gold as a carrier. Specimens , were freshly abraded on 4/0 emery paper immediately prior to plating. In the case of the active couples disks of a similarly prepared but unplated alloy or pure metal were placed on top and welded to the active disk. With the concentration couples disks of different compositions were welded. Welding was performed after a pressure of 5,000 lb had been applied at

Jan 1, 1958

By J. B. Cohen, O. F. Kimball

Aging of specimens of Au-20 at. pct Ni and Au-40 at. pct Ni has been followed with electron microscopy, resistance, magnetic measurements, and X-ray diffraction. The periodic structures observed by electron microscopy in Au-Ni alloys by Fisher and Embury are shown to be due to nickel-rich prepre-cipitates. Assuming this alloy system undergoes spinodal decomposition, our observations and available data on thermodynamic properties and elastic constants indicate that the gradient energy coefficient in this system is of the order of 10-5 ergs cm-1 . Shifts of X-ray peaks in this system have been found to be due primarily to residual stresses, not faulting. A large effect of applied stress during aging was detected by X-rays and electron microscopy for the Au-20 at. pct Ni alloy. The presence of a preprecipitation stage during aging of gold-rich Au-Ni alloys for short times below 300°C has been indicated by several previous investigations. Changes in electrical resistivity,1"3 elastic modulus,4 superparamagnetisrn,5 positions of X-ray diffraction peaks,6 and hardness7 have been studied. Electron diffraction and microscopic studies by Fukano8 and Fisher and Embury9 respectively showed that the precipitation process resulted in the formation of periodic composition fluctuations—perhaps spinodal decomposition. MOSS10 detected a satellite with X-rays in quenched specimens, but the wavelength was much smallerthan that found by Fukano. Recently Woodilla and Averbac11 detected a modulation similar to that found by Moss, but with electron diffraction. They suggested that the microstructures observed by Fisher and Embury may be simply due to a Moir'e effect from a back deposit of gold during electropolishing. Satellites in electron diffraction can be enhanced by small bends or tilts of a foil. Even if this were not the case, asymmetric satellites, as are found in Au-Ni are difficult to analyze. They are principally influenced by the large differences in atomic size in this system, and obtaining information on the associated composition fluctuations depends on assumptions as to whether or not there are isolated clusters or composition "waves", and in the latter case whether or not the entire specimen has decomposed. Assuming that decomposition was complete in alloys aged at low temperatures, Woodilla and Averbach suggested that the satellites indicated a composition which varied about the average value by only± 5 pct, much less than that predicted from the phase limits, Fig. 1; they attributed this small variation to a cessation of the reaction caused by the loss of mobile vacancies. In Ref. 12 it was shown that vacancies are trapped by the preprecipitate in this system. Furthermore, after reversion, aging proceeds at a much slower rate than immediately after a quench from the solution temperature,5'11,13 indicating the importance of vacancies in the kinetics. In some senses Au-Ni is a favorable system for studying preprecipitation and reversion mechanisms because of the simplicity of the equilibrium diagram14 and the availability of good thermodynamic15 and diffusion data.16,l7 The calculations necessary to relate the decomposition process to classical nucleation and growth or to spinodal decomposition, as well as those necessary for understanding reversion mechanisms, can, therefore, be made. As an example, the position of the chemical spinodal, calculated from the thermo-dynamic data of Sellars and Maak15 with the method described by Rundman and Hilliard,18 is included in Fig. 1. It is compared to the chemical spinodal calculated from the equilibrium miscibility gap by Cook and Hilliard's method.l9 Included is the coherent spinodal suggested by Golding and MOSS," using measured elastic constants for their calculations and the same ther-modynamic data. The spinodal estimated by Woodilla and Averbach,11 by determining the temperature limits for the observation of the satellites discussed above, is also given. Actually this last curve is open to question on the following grounds: As a phase boundary is approached the spacing of particles or the wavelength

Jan 1, 1970

By R. E. Delavault, H. V. Warren

In normal soils there are usually 10 to 50 parts of copper in every million parts of .soil. Only 0.2 to .5 pct of this copper can be found by any simple cold chemical attack. Now, with rubeanic mid reagent paper, a prospector or field geologist can detect as little us 4 ppm of readily available copper ill soil. This degree, of sensiticity is enough to determine the presence. of copper anamalous an as and, ecentually, to discouer copper mineralization. Circumstances determine whether it is better to make analyses in the field or in a permanent laboratory. The rubeanic acid test described in this article has been designed primarily for field use: it is simple and virtually foolproof, and it requires a minimum of field kit." It is sensitive, easily de- • Ed. Note: Persons Interested in purchasing kits suitable for rubeanic acid prospecting can obtain information by writing Eldrico Geophysical Sales Ltd., 633 Hornby Street. Vancouver 1, B.C. The University of British Columbia does not produce these kits for sale and has no financial interest in their production tecting 4 ppm of readily extractable copper in a soil. This is by no means a quantitative test, but it is accurate enough to provide a valuable indicator of copper anomalous areas for both prospectors and field geologists. The easiest method for detecting metal deposits that do not produce visible float or stains is to make a simple chemical test for the metal in overlying soil, or in the silt of a stream that may have picked up metal farther upstream. In Brief: Testing for copper may be done easily by shaking a soil sample with strong acetic solution in a small test tube and pouring the mud into a small filter, the tip of which rests upon a strip of reagent paper impregnated with rubeanic acid (di-thio-oxamide). When copper is present—and only when it is—a blue spot develops. The more copper, the darker the spot. If the copper content is merely the small amount present everywhere, there is a pale blue or hardly visible spot; if it is abnormally high, the spot will be dark. There are, of course, intermediate cases where the experienced geochemist cannot tell offhand whether a medium-strength spot represents rich agricultural soil, weak copper mineralization, or distant rich copper mineralization. Reagents and material are inexpensive; the test may be readily done on the spot with a simple kit easy to pack and handle. Anyone interested in general problems of soil sampling as applied to prospecting may refer to an article recently presented to the AIME. In exploration work it is the contrast between the metal content of anomalous and background areas that is important; absolute values become of greater interest when an anomalous area is being investigated in detail. With specific reference to copper, it has been the authors' experience that the amounts of metal extracted from anomalous and normal soils with buffer solutions of decreasing pH show better contrast if an acid reagent is used. This contrast tends to increase with increasing acidity until 3 to 4 pH is reached. Using a short cold attack on unheated soil, it has been found that further increases in acidity do not produce better results, and only increase the hazards involved in carrying strong acids. An acidity of about pH 4 is satisfactory for direct determination of copper by dithizone. But dithizone itself introduces some problems: it must be made up fresh at frequent intervals, and with some soils, notably those with much ferric iron, oxidation mag take place before all the copper has reacted with the dithizone. Rubeanic acid keeps its strength unimpaired for long periods, is unaffected by oxidation, and is practically specific for copper at pH 4. Consequently it seems an ideal reagent to use in prospecting for copper. History and Background: Rubeanic acid (systematic name: dithio-oxamide (SC-NH2) has long been known as a spot test reagent for some heavy metals with which it gives a number of compounds. Only copper and some metals of the platinum family are believed capable of providing any ru-beanate compounds under conditions of moderate

Jan 1, 1959

By G. Osuch, G. Derge, G. M. Pound

Using a new dternating-current potentiometer circuit and a specially designed four-terminal cell, the specific conductance of molten Cu2S-FeS mattes was measured as a function of temperature, from the liquidus to 1500°C, over the complete range of composition. The high conductivities, about 1500 ohm-I cm-l for FeS and 100 ohm-l cm-l for Cu,S, indicate that the conduction is electronic rather than ionic. Molten FeS has a negative temperature coefficient of specific conductance, resembling metallic conduction. Molten Cu,S has a positive temperature coefficient, resembling semiconduction. The binary roughly follows an additive rule of mixtures with respect to both magnitude and temperature coefficient of specific conductance. Metallic bonding in the liquid is postulated to explain these phenomena. MUCH has been learned in the past about the nature of liquids and the ionic or molecular species in solution by means of electrical measurements. Thus, dielectric constants','2 have given information about molecular liquids such as water and benzene. Measurements of dielectric constant usually are impossible in electrically conducting liquids, such as aqueous solutions of ionic salts and molten ionic salts. However, measurements of electrical conductance and ionic transference have provided much knowledge about the latter systems.a-" In recent years, the ionic nature of certain molten metallurgical slags has been established by Derge and Martin7 through electrical conductance and electrolysis measurements. Chipman, Inouye, and Tom-linsonq ave studied the electrical conductance of molten FeO and report a high specific conductance of about 200 ohm-' cm-' (compared with 4 ohm" cm-' for an ordinary ionic liquid such as molten NaCl) and a positive temperature coefficient of conductance. They interpret these results in terms of p-type semiconduction by analogy to the situation in solid FeO.Y imnad and Derge" have studied cell efficiency in the electrolysis of molten FeO-SiO, systems and conclude that ordinary ionic conductance increases with SiO, content. Very recently, interest has been revived in the electrical conductance of liquid metals and liquid metallic solutions. Scala and Robertson1' report a close resemblance between the liquid and solid states with respect to thermal, structural, and compositional relationships. Molten sulphides have not received a great deal of attention. Bornemann and von Rauschenplat" measured the specific conductance of molten Cu2S as a function of temperature with a four-terminal cell using direct current. A high specific conductance and a positive temperature coefficient were found in that investigation." Using a two-electrode apparatus, Savelsberg" electrolyzed various molten sulphide mixtures. He concluded that pure molten Cu,S and FeS were electronic conductors but that the mixtures exhibited some ionic conduction. In the present investigation, the specific conductance of the industrially important Cu-Fe sulphide mattes was measured as a function of temperature and composition in order to investigate the mode of electrical conduction and the structure of these molten mattes. An alternating-current circuit was used to eliminate the effect of any possible electrode reactions. Apparatus The Conductance Cell: Due to the high specific conductance of the systems studied (10' to 10" ohm-' cm-'), the classical two-terminal cell and Wheat-stone bridge apparatus could not be used. A four-terminal cell was developed in order to eliminate lead resistance, and an ac potentiometer circuit was designed to give rapid and sufficiently accurate measurements of the cell resistance. A diagram of the conductivity cell is given in Fig. 1. The molten matte is contained in a dense alundum crucible, and spectrographic graphite rods that dip into the molten matte serve as the four conductance terminals. Two of the graphite rods on opposite sides of the cell serve as current-carrying leads, and the other two graphite rods are null-current probes that detect the potential drop across the cell. These graphite rods are contained in silica tubes, and the lower constricted portions of the two silica tubes define the column of liquid whose electrical resistance is being measured. The electrical resistance of the broad ex-

Jan 1, 1956

By R. G. Treuting, W. C. Ellis

The twinned state is characterized by a lattice of coincidence sites. Imperfections are required at stable lateral twin interfaces. Twinned regions can occur with relative ease in the diamond cubic IN recent contributions1,2 on the origin and growth of cubic annealing twins, attention has been directed to the orientation relations between such twinned components and their parent matrix. There are some aspects of twinning which may be illuminated by a more detailed consideration of the twinned state" alone. As an extreme example, the dense twinning in cast ingots of germanium,&apos; as contrasted with the rarity of twins in cast face-centered cubic metals, is yet to be accounted for. It has been this that has led us to the present work, which, it will be noted, uses methods and constructions in many respects similar to those of Kronberg and Wilson.&apos; In the cubic systems, a 70" 32&apos; rotation about a <110> axis is angularly equivalent, as to twinning, to the more usually considered 180" rotation about a <111> axis. Figs. 1 and 2 show a (110) projection of a twinned face-centered cubic lattice and a twinned diamond cubic lattice. In both figures, the two adjacent planes A and B, shown by the larger and smaller circles, are sufficient to represent the entire array. In each case a section of lattice, the original atom sites of which are shown by open circles, has been rotated as indicated through 70" 32&apos; to bring an original. [112] direction into coincidence with the [112] diiection. The latter is the intercept on the (110) projection of the (ill) plane normal thereto, the twinning plane. In the face-centered cubic case the rotation can be performed about an axis passing through an atom-site; the mirror plane then is also a composition plane containing atoms common to both twinned and untwinned lattices. The diamond cubic lattice may be construed as two interpenetrated face-centered lattices. Its (111) planes recur in a sequence of alternately short and long interspacings. Consequently a mirror plane for twinning cannot be a composition plane, but must be the bisector of one of the spacings. When the longer spacing is selected, the closest distance of approach across the mirror plane in the [ill] direc- tion is identical with that in the untwinned structure. In each case periodically recurring (ill) planes (parallel with the twinning plane) are found, on which there is coincidence of atom sites of the pre-twinned and twinned orientations; these are indicated by the cross-hatched circles. In the face-centered lattice there is such coincidence every third (ill) plane; in the diamond cubic lattice, on two adjacent planes in every six. At the twinning interface in the latter, there is on each side of the mirror plane a (ill) plane of atoms common to both twin components. Conceivably, there is little influence on a plane of atoms about to be adhered to such a pair of coincidence planes, whether it be laid down in a normal or in a twinned position with respect to the previously formed structure. Slawson% as attributed the high incidence of twinning in diamond to this boundary state. Further examination shows that the motion of intermediate planes can consist of various pairs of equal and opposite translations, for example of (ill) planes in the [l&apos;;i2) direction, the familiar twinning shear, indicated in the small schematics in the figures. Since the translations form a system of shears of alternating sign between coincidence planes, twinning could take place by such a mechanism over an extended region without extensive shear; in fact, in this case any atom moves but the distance in the [1i2] direction. One alternative construction for the face-centered cubic lattice leading to the same end result is illustrated in Fig. 3. The plane (711) with respect to the pretwinning orientation (the twinning plane of Fig. 1) is given, the twinned region arbitrarily bounded by <110> and <112> directions. The coupled shear is identical to that of Fig. 1. The "rotational" movement about coincidence sites generating the same twinned position could consist as shown of the translation a,/d% for each atom of a group of three in the B layer in a different one of the three <112> directions, and a similar translation of the underlying three atoms in the C layer in either the same or the opposite sense. This is not dissimilar to Kronberg and Wilson&apos;s construction for their 22" rotation of three adjacent (111) planes.

Jan 1, 1952

By P. E. Doherty, B. Chalmers

Subboundaries may be revealed in aluminum by the formation of pits on the surface during cooling from elevated temperatures. The pits do not form in the vicinity of high- or low-angle boundaries. They are attributed to the condensation of vacancies from a super saturation produced during coolirzg. Using the vacancy pit and Schulz X-ray techniques for observing low-angle boundaries, a study was made of the transition from the nearly perfect seed to the striated structuke characterist-ic of aluminum crystals grown from the melt. It was found that the individual striation boundaries develop by the coalescence of very small-angle boundaries, as well as by the addition of individual dislocations. Several mechanisms for the formation of striations are discussed. Evidence was found suggesting that a super-saturation of vacancies exists near a growing interface, and it is proposed that the resulting climb of existing dislocalions produces "half&apos;-loops" at the interface, which combine to form the low-angle striation boundaries. LINEAGE, or "striation" boundaries, have been studied in detail by Teghtsoonian and Chalmers 1,2 in crystals of tin grown from the melt, and by Atwater and Chalmers3 in lead. They found that single crystals grown from the melt consist of regions which are separated by subboundaries that lie roughly parallel to the growth direction. A difference in orientation of 0.5 to 3 deg exists between the striated regions; the misorientation is such that the lattice of one region could be brought into coincidence with the lattice of its neighbor by a rotation about an axis approximately parallel to the direction of growth of the crystal. They observed an incubation distance for the formation of striations which increased with decreasing growth rate. They also found that in any crystal, the sum of all rotations of the lattice in one sense, in going from one striation to the next, is very nearly equal to the sum of all the rotations in the opposite sense. A striation boundary, which is a low-angle grain boundary, can be described as an array of dislocations. If it is assumed that suitable dislocations are introduced into the crystal during solidification, the formation of striation boundaries can be explained as a result of the migration of the disloca- tions into arrays. The formation of arrays is energetically favorable since the energy of an assembly of dislocations can be reduced by the interaction of the stress fields when a suitable array is formed. This investigation presents and interprets new information concerning the nature and origin of striation boundaries in aluminum. EXPERIMENTAL TECHNIQUE Single crystals of high-purity aluminum (Alcoa 99.992 pct) were prepared by horizontal growth from the melt.&apos;&apos; The specimens were subsequently electropolished in a solution of 5 parts methanol to 1 part perchloric acid kept between -10° and 0°C in a bath of dry ice and alcohol. The current density was approximately 6 amps per sq in. Doherty and Davis9 have shown that in aluminum sub-boundaries with misorientations of not less than several seconds of arc may be revealed by the vacancy pit technique. During cooling from elevated temperatures pits form on electropolished surfaces of aluminum crystals as a result of the condensation of vacancies.11 Pits do not form in the vicinity of small- or large-angle grain boundaries, presumably because such boundaries act as sinks for vacancies. Boundaries of misorientations down to 3 sec of arc are revealed as pit-free regions, see Fig. 1. The Schulz X-ray technique12 was used to determine the angular misorientations of subboundaries. In this method, white radiation from a micro-focus X-ray tube is used to produce an image of a fairly large area of a single crystal surface. Subboundaries cause splitting in the diffracted image, see Fig. 2. Misorientations down to about 15 sec of arc may be observed with this technique. OBSERVATIONS AND DISCUSSION Figure 1 shows a striated aluminum crystal grown at 10 cm per hr etched by the vacancy pit technique. An incubation distance of about 1 cm is observed before the initiation of striation boundaries. Fig. 2 is a Schulz X-ray photograph of a striated crystal similar to that shown in Fig. 1. A large area of the crystal was studied by means of a series of photographs. Fig. 2, which is a reflection from the (100) plane, included about the first 4 cm of crystal to freeze. There is an incubation distance of about 1 cm, and a distance of about 2 cm over which the angle of misorientation builds up to its final value of approximately one degree. Some twist component can be seen in Fig. 2 at the right side of the photograph. From Fig. 2 it can be seen that the sum of all rotations of the lattice in one

Jan 1, 1962

By A. Y. Bethune, W. G. Woolf

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process&apos; for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt&apos;s earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.&apos;s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By W. G. Woolf, A. Y. Bethune

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process&apos; for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt&apos;s earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.&apos;s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By R. T. DeHoff

In any structural transfortnation which is driven by surface tension, the geometric variable of fimdamental importance is the local value of the mean surface curvatuve. Acting through the suvface free energy, this quantity determines the magtnitude of both the pressure and the chemical potential that develops in the neighborhood of an arbitrarily curved surface. A metallographic method which would permit the quaniitatiue estinzation of this propevty is of fundarnerztal irztevest to studies of such processes. In the present paper, it is shoun that the average value of the mean surface curvature in a structuve can be estimated from two simple counting measuretnents made upon a vepresentative metallograpIzic section. No simplifyirlg geonzetric assurmptions are necessary to this deviuation. It is further shoum that the result may be applied to parts of interfaces, e.g., interparticle welds in sintering, or the edge of growing platelets in a phase transformation, without loss of validity. In virtually every metallurgical process in which an interface is important, the local value of the mean surface curvature is the key structural property. This is true because the mean curvature determines the chemical potential of material adjacent to the surface, as well as the state of stress of that material. The theoretical description of such broadly different processes as sintering,1,2 grain growth,3 particle redistrib~tion4,5 and growth of Widmanstatten platelets8 all have as a central geometric variable the "local value of the mean surface curvature". The tools of quantitative metallography currently available permit the statistically precise estimation of the total or extensive geometric properties of a structure: the volume fraction of any distinguishable part:-&apos; the total extent of any observable interface,10,11 and the total length of some three-dimensional lineal feature:&apos; and, if some simplifying assumptions about particle shape are allowed, the total number of particles.&apos;2"3 The size of particles in a structure, specified by a distribution or a mean value, can only be estimated if the particles are all the same shape, and if this shape is relatively simple.14-16 The relationships involved in converting measurements made upon a metallographic section to properties of the three dimensional structure of which the section is a sample are now well-established, and their utility amply demonstrated. In the present paper, another fundamental relationship is added to the tools of quantitative metallography. This relationship is fundamental in the sense that its validity depends only upon the observation of an appropriately representative sample of the structure, and not upon the geometric nature of the structure itself. It involves a new sampling procedure, devised by Rhines, called the "area tangent count". It will first be shown that the "area tangent count" is simply related to the average value of the curvature of particle outline in the two-dimensional section upon which the count is performed. The average curvature of such a section will then be shown to be proportional to the average value of the Mean surface curVature of the structure of which the section is a sample. The final result of the development is thus a relationship which permits the evaluation of the average value of the mean surface curvature from relatively simple counting measurements made upon a representative metallographic section. The result is quite independent of the geometric or even topological nature of the interface being studied. QUANTITATNE EVALUATION OF AVERAGE CURVATURE IN TWO DIMENSIONS The Area Tangent Count. Consider a two-dimen-sional structure composed of two different kinds of distinguishable areas (phases), Fig. l(a). If the system is composed of more than two "phases", it is possible to focus attention upon one phase, and consider the remaining structure as the other phase. The reference phase is separated from the rest of the structure by a set of linear boundaries, of arbitrary shapes and sizes. These boundaries may be totally smooth and continuous, or piecewise smooth and continuous. An element of such a boundary, dA, is shown in Fig. l(b). One may define the "angle subtended" by this arbitrarily curved element of arc, dO, as the angle between the normals erected at its ends, Fig. l(c). Now consider the following experiment. Let a line be swept across this two-dimensional structure, and let the number of tangents that this line forms with elements of arc in the structure be counted. This procedure constitutes the Rhines Area Tangent Count. Suppose that this experiment were repeated a large number of times, with the direction of traverse of the sweeping lines distributed uniformly over the semicircle of orientation.&apos; Those test lines which ap- proach from orientations which lie in the range O to O + dO form a tangent with dA; those outside this range do not, see Fig. l(c). Since the lines are presumed to be uniformly distributed in direction of traverse, the fraction of test lines which form a tangent with dA is the fraction of the circumference of a semicircle which is contained in the orientation range, dO; i.e., vdO/nr or dB/n. If the number of test lines is N, the number forming tangents with dA is N(d0/n). Since each test line sweeps the entire area of the sample, the total area traversed by all N test lines is NL2. The number of tangents formed with dA, per unit area of structure sampled, is therefore

Jan 1, 1968