Search Documents

By Mark D. Tabak

Measurments of the transient photoconductivity in fillns of amorphous selenium with blocking- contacts haue been used in studying the transport properties. The results shozu that the transport of free carviers cannot be explained in terms of a model using bulk trapping. Measurments of the photocurrent-applied field characteristic as a unction of sample thickness do not pvoduce the scaling lau,s approps-iate lo a range-limited model. THE investigation described here was undertaken to explore the mechanisms of transport in amorphous selenium films. These films are used in xerography, where a photoconductor is charged electrostatically and then exposed to light to form a latent image. The sensitivity that one can expect when operating in this mode is directly related to the transport properties of the photoconductor material. The study of photoconductivity at high fields in insulating materials is often complicated by contact effects. Injection from the contacts can easily mask the fundamental transport processes that are being studied. A technique is described in this paper that allows a study of photoconductivity and transport processes in amorphous selenium films without the complicating effects introduced by contacts. Accordingly, the samples are prepared using insulating films between the sample and the metal electrodes, where the electrodes are capacitively coupled to the surfaces of the sample under study. A transient measurement is performed with pulsed light, and the photocurrent measured near the beginning of the pulse before the field is distorted by polarization at the blocking elec- trodes. A similar method has been described by Manyl using pulsed electric fields in studying the high field transport in insulating cadmium sulfide. EXPERIMENTAL It is possible to eliminate undesirable contact effects and maintain uniform high fields across the sample by using blocking electrodes and measuring the current-field characteristic under transient conditions. The sample configuration is shown schematically in Fig. 1. Each of the gold electrodes is separated from the amorphous selenium film by a layer of insulating plastic (Formvar) approximately 2000~ thick. The electrode on the front surface is semi-transparent to allow illumination of the sample. The whole configuration is mounted on a KEL-F substrate, which is a transparent insulating plastic having a thermal expansion coefficient that allows low-temperature measurements without cracking the selenium film. Fig. 2 shows a block diagram of the measurement apparatus. Light was obtained from a 450-w Xenon arc lamp, the intensity of which was controlled by stainless-steel screen filters and monitored by a pho-tomultiplier which was calibrated periodically against a thermopile. A camera shutter operated at 1/200 sec provided the light pulse and a synchronized signal to the oscilloscope. The photocurrent transient is ob-served with a high-speed picoammeter (response time of 1 msec) the output of which is displayed on an oscilloscope. The applied voltage is constant throughout the transient measurement. The selenium films were prepared by evaporation of four 9's pure selenium shot supplied by Canadian Copper Refiners. Spectrographic analysis showed about 1 ppm of Te and Fe, 5 ppm of C1, and 0.05 ppm

Jan 1, 1968

By C. S. Barrett

The torsional after-effect in polycrystalline cadmium is interrupted by an abnormal twisting when the film is removed by etching. This is accounted for by the pile-up of dislocations beneath anodic or other oxide films during the original twisting, and the relief of the residual stresses from these by elastic and plastic processes during etching. WHEN an iron or zinc wire coated with oxide is plastically twisted and then released, it untwists according to a law of equal increments in equal intervals of log time, but if the oxide is suddenly removed by etching this normal after-effect is interrupted by a transient, and thereafter the untwisting is slower.' Etching may even reverse the strain temporarily. Related effects caused by hydrated oxide films on cadmium in creep tests have been observed by Phillips and Thompson:' definite transient strains caused by the removal of the film from single crystals of cadmium were observed; however, negligible effects were obtained with polycrystalline wires. Pronounced effects of both transient and steady nature were observed by Phillips and Thompson when anodic films 10-4 cm thick were etched off, and weak effects, transient only, occurred with hydrated oxide films 3x10 cm thick such as were formed by standing in water for 10 min. It was estimated that 10.' cm films, formed in water in 1 or 2 min, could be detected in the apparatus of Phillips and Thompson. Since abnormal after-effects were observed by the torsion method equally well with polycrystalline and monocrystalline iron and zinc wires,' it was anticipated that the torsion method would also disclose them in polycrystalline cadmium, in spite of the fact that analogous effects had not been observed in tensile creep tests on polycrystalline zinc by Pickus and Parker3 r on polycrystalline cadmium in tensile studies by Andrade and Randall." Because of its high sensitivity, particularly its sensitivity to surface conditions, the torsion method was thought to merit further study as a method of investigating thin films of various types and the action of various reagents on these films. Materials and Methods Cadmium wires were cold-drawn to a diameter of 0.039 in. from a stock that was determined spectro-scopically to contain 0.05 pct Bi, 0.005 pct Cu, 0.008 pct Pb, and 0.007 pct Si. The wires were cut to about 17/8 in. lengths and were annealed 1 hr in air at 290°C, after which the grain size was such that there were 5 to 7 grains across a diameter. The wires were then mounted as indicated in the insert in Fig. 1, one end being fastened with laboratory wax into a small diameter brass tube and the other end being waxed to a thin glass fiber which supported, on its upper end, a small galvanometer mirror. The wires were waxed with care to avoid straining or annealing, for it was found that the after-effect rate was sensitive to prior cold work in a wire. The assembly was then clamped above a beaker into which the reagent could be poured. The lower end of the wire was held in the hand while the wire was twisted 180"; it was then released immediately. Since precision timing of these manipulations was not attempted, the different wires cannot be compared as to exact rates of untwisting. The length subjected to plastic strain was 15/8 in. The surface coatings studied were those produced by the annealing in air, by anodic treatment of

Jan 1, 1954

Executive JVW REYNOLDS, Chairman SYDNEY H BALL E DEGOLYER WILLIAM H BASSETT SAMUEL A TAYLOR Finance GEORGE D BARRON, Chairman H A GUESS GEORGE OTIS SMITH Membership ] H CALLOW, Chairman GEORGE D BARRON WILBER JUDSON JOHN A CHURCH, JR H N SPICER Alternates LEWIS W FRANCIS LOUIS D HUNTOON F T RUBIDGE

Jan 1, 1923

By J. L. Whitlock

An attached growth aerobic biological treatment process has been developed at Homestake Mining Co.'s Lead operation which not only oxidizes free and complexed cyanides, including the stable iron complexed cyanides, but also thiocyanate, and the oxidation byproduct ammonia. Through the employment of a mutant strain of bacteria which has been gradually and specifically acclimated to the waste, these potential pollutants are mineralized to relatively harmless sulfates, carbonates, and nitrates. The resultant effluent, through toxicological testing, has been shown compatible with the receiving stream, which serves as a cold water marginal trout fishery.

Jan 1, 1985

By Charles S. Barrett

Recrystallization textures—thc orientations of grains after recrys-tallization—have been studied extensively not only because of their metallurgical importance but also because of the information they yield regarding the atomic movements during reerystallization. Recrystallized grains must possess the same orientations as the submicroscopic nuclei from which they have grown, and thus they offer a direet road by which experimenters can penetrate the submicroscopic realm. Many perplexing results have come of these studies, but one of the most striking has been the apparent difference in behavior between single crystals and polyerystalline grains. For example, Burgers and Louwerse have shown1 that when single crystals of aluminum are deformed by compression and are reerystallized (at 600' C.) the new grains appear with orientations that are different from the orientations of the deformed crystal in which they grew; but polycrystalline specimens, on the other hand, appear to have a [110] fiber texture both before and after reerystallization and thus to retain their texture during recrystallization. This apparent difference between the habits of single crystals and small grains is the subject of the first part of the present research and has been explained by findings reported herein. A similar situation appears to exist for aluminum when elongated or drawn into wires, for single crystals alter their orientation 2,3 and polycrystalline wires retain their texture"5*" upon recrystallization after elongation (at least with high-purity aluminum), and it is possible that the explanation found in this paper for compression can be extended to cover elongatioil and other types of deformation as well. The second part of this paper deals with the theory of reerystallization textures. In the most successful theory for aluminum reerystallized after compression,1 much weight is given to the orientation of highly stressed nuclei in the deformed material. Taylor's "local distortions" arc assumed to exist along the slip planes where displacement has occurred, consisting of fragments rotated in a specific way with reference to the slip plane and slip direction; namely, about an axis lying in the slip plane perpendicular to the slip direction.1,7,89

Jan 1, 1940

By Charles S. Barrett

Recrystallization textures—thc orientations of grains after recrys-tallization—have been studied extensively not only because of their metallurgical importance but also because of the information they yield regarding the atomic movements during reerystallization. Recrystallized grains must possess the same orientations as the submicroscopic nuclei from which they have grown, and thus they offer a direet road by which experimenters can penetrate the submicroscopic realm. Many perplexing results have come of these studies, but one of the most striking has been the apparent difference in behavior between single crystals and polyerystalline grains. For example, Burgers and Louwerse have shown1 that when single crystals of aluminum are deformed by compression and are reerystallized (at 600' C.) the new grains appear with orientations that are different from the orientations of the deformed crystal in which they grew; but polycrystalline specimens, on the other hand, appear to have a [110] fiber texture both before and after reerystallization and thus to retain their texture during recrystallization. This apparent difference between the habits of single crystals and small grains is the subject of the first part of the present research and has been explained by findings reported herein. A similar situation appears to exist for aluminum when elongated or drawn into wires, for single crystals alter their orientation 2,3 and polycrystalline wires retain their texture"5*" upon recrystallization after elongation (at least with high-purity aluminum), and it is possible that the explanation found in this paper for compression can be extended to cover elongatioil and other types of deformation as well. The second part of this paper deals with the theory of reerystallization textures. In the most successful theory for aluminum reerystallized after compression,1 much weight is given to the orientation of highly stressed nuclei in the deformed material. Taylor's "local distortions" arc assumed to exist along the slip planes where displacement has occurred, consisting of fragments rotated in a specific way with reference to the slip plane and slip direction; namely, about an axis lying in the slip plane perpendicular to the slip direction.1,7,89

Jan 1, 1940

HE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given composition and quality. In comparison with other steelmaking methods, the basic open-hearth process is one of the most versa- tile, both from the standpoint of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. With some types of liquid-metal charges, the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO). This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SiO2) , manganese oxide (MnO), iron oxides (FeO and Fe2O3), and phosphorus oxide (P2O5) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course

Jan 1, 1951

By R. W. Raymond

THE absence of a convenient glossary of terms connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale's work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copp, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who have favored me with assistance and advice. The labor bestowed upon this paper since its presentation at the Lake Superior meeting has considerably exceeded that of its first preparation, as may be inferred from its great increase in length, as well as the numerous alterations which it has undergone. It could certainly be still further enlarged and improved; but I think a comparison of it with any of the glossaries of the same class now in print will show, at least, that it is an advance upon what has hitherto been accomplished. 1 shall be grateful, however, for further criticisms and suggestions; and I purpose at some future time to incorporate in a supplementary paper the results of such additional collections or corrections as I may obtain. To avoid too great prolixity, I adopted at the outset the following general principles: 1. To include the most important technical words and phrases used by American miners and metallurgists, or occurring in English books and periodicals.

Jan 1, 1881

By Charles Barrett

RECRYSTALLIZATION textures-the orientations of grains after recrys-tallization-have been studied extensively not only because of their metallurgical importance but also because of the information they yield regarding the atomic movements during recrystallization. Recrystallized grains must possess the same orientations as the submicroscopic nuclei from which they have grown, and thus they offer a direct road by which experimenters can penetrate the submicroscopic realm. Many perplexing results have come of these studies, but one of the most striking has been the apparent difference in behavior between single crystals and polycrystalline grains. For example, Burgers and Louwerse have shown' that when single crystals of aluminum are deformed by compression and are recrystallized (at 600° C.) the new grains appear with orientations that are different from the orientations of the deformed crystal in which they grew; but polycrystalline specimens, on the other hand, appear to have a [110] fiber texture both before and after recrystal-lization and thus to retain their texture during recrystallization. This apparent difference between the habits of single crystals and small grains is the subject of the first part of the present research and has been explained by findings reported herein. A similar situation appears to exist for aluminum when elongated or drawn into wires, for single crystals alter their orientation2,3 and polycrystalline wires retain their texture 4,1 6 upon recrystallization after elongation (at least with high-purity alumi-num), and it is possible that the explanation found in this paper for compression can be extended to cover elongation and other types of deformation as well. The second part of this paper deals with the theory of recrystallization textures. In the most successful theory for aluminum recrystallized after compression,1 much weight is given to the orientation of highly stressed nuclei in the deformed material. Taylor's "local distortions" are assumed to exist along the slip planes where displacement has occurred, consisting of fragments rotated in a specific way with reference to the slip plane and slip direction; namely, about an axis lying in the slip plane perpendicular to the slip direction. 1,7,8,9

Jan 1, 1940

By Robert E. Brand, Strathmore R. B. Cooke

For a study of the bonding that occurs in magnetite pellets during oxidation, cubes of magnetite, hematite, and quartz were prepared, each with one surface polished and nearly optically plane. These faces were fired together under pressure and at various temperatures to determine whether bonding would occur. Sections of surfaces that bonded were examined microscopically. An attempt was made to measure the strength effected by this treatment. EARLIER work1,2 has shown that the strength developed by fired magnetite pellets containing silica or silicates is due to three separate effects. Two of these are associated with the formation of slag in the interior of each pellet at temperatures above 1000°C, where the atmosphere is substantially though temporarily neutral. The third is independent of the silica content and is responsible for the development of a hard shell around the pellet during the initial stages of firing, a condition which permits the pellet to assume the increasing load of the overlying burden and prevents extrusion of the slagged and semi-liquid interior. Pellets made from hematite concentrates do not show these effects unless specific additives are incorporated, and it is these differences in behavior which in large part account for the difficulty in producing satisfactory pellets from such concentrates. Elsewhere it has been stated that "the most important factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of magnetite to hematite and the subsequent recrystallization and grain growth of this constituent."' The object of the investigation reported in the present paper was to study in detail the mechanism described above and to evaluate its contribution to the strength of the fired pellet compared with other possible mechanisms, excluding slag bonding. This was effected by placing together polished faces of two cubes prepared from specific minerals and then heating them under constant pressure at different temperatures both in air and in nitrogen. The materials used were magnetite, hematite, and quartz. The magnetite was coarsely crystalline material from western Montana, the hematite was Itabira ore from Brazil, and the quartz was of optical grade but of unknown origin. A high-grade Lebanon (Pennsylvania) magnetite concentrate was used to prepare briquets for the investigation of bonding strength. Analyses of the iron oxide materials are given in Table I. The specimens for furnace treatment were prepared with a carborundum cut-off wheel, which cut the minerals into cubes approximating % in. along each edge. Care was taken to make the sides as parallel as possible. The edges of the faces to be polished were beveled, and the cubes were mounted in brass rings with sealing wax, this being essential to prevent the specimens from rocking during polishing. To prevent excessive friction, the wax was recessed so that only the brass ring and the face of each specimen would be in contact with the polishing lap. Each specimen was then ground with No. 600 carborundum to produce a level surface before polishing. The Graton-Vanderwilt process was not used for polishing because of the long time required by this method, but several other methods were tried. Cloth laps using levigated alumina or chromium oxide did not produce the desired polish. Satisfactory results were obtained by means of a pitch lap: which was used for all the mineral cubes, with levigated alumina as the polishing medium. The lap was operated in a machine similar to those used in the preparation of single optical surfaces. It was run at low speeds and moderate pressures, and polishing was stopped occasionally to prevent overheating of the lap. A good polish with flat surfaces could be obtained in about 5 min. After polishing the sealing wax was removed either in hot water or in a solvent such as turpentine.

Jan 1, 1955

By William A. Edmiston, R. E. Grace

A simplified model for the theory of reaction rates near equilibrium has been applied to the reduction of wustite. A linear relationship between the net rate of reaction and the Gibbs free-energy change, ?F, is predicted. The reduction of wustite in H2 -H2O gas mixtures was studied with a microbalance technique at temperatures from 850° to 950 °C. The predicted model was found to be valid to -?F/RT = 0.1 or approximately -200 cal per mole away from equilibrium. ThE theory of reaction rates near equilibrium has been developed by a number of authors. Prigogine, Outer, and Herbo1 have studied the catalytic hydrogena tion of benzene in an attempt to deduce some intrinsic connection between reaction rates near equilibrium and thermodynamics. Manes, Hofer, and weller2 have derived more general expressions for reaction rates near equilibrium from classical thermodynamics. Hollingsworth3,4 has commented briefly on the work of Manes et al. Benson5 has summarized in a general way the results of the earlier contributions. It is the purpose of this paper to apply the theory of reaction rates near equilibrium specifically to the reduction of wustite in H2-H2O gas mixtures. The basic premise is that the reduction of wustite proceeds by a surface reaction, rather than by solid-state diffusion ,or gaseous diffusion. Richardson and Dancy6 and Gellner and Richardson7 have suggested that the reduction of wustite may be governed by iron diffusion in wustite. Mckewan8-11 has proposed that reduced iron layers on various oxides are sufficiently porous to offer a negligible impedance to the reducing gas. The linear motion of interfaces reported by McKewan and discussed by Themelis and Gauvin12 indicates the lack of diffusive control during reduction. The reduction studies of magnetite reported by Quets, Wadsworth, and Lewis13 give additional evidence that reduction rates are linear when the reaction products are porous and nonprotective. The interpretation of measurements reported in this paper is predicated upon a surface-controlled reduction reaction, at least in the earliest stages of reduction when the reduced iron layer is thin.

Jan 1, 1967

By W. W. Gorr, R. Smith, E. H. Wyche

THE combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W? and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. DEVELOPMENT OF THE NEW STEEL For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield 18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators 'then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, o.58; Ni, 7.28; Cr, 17.6o; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1946

By Sherwin Kelly

IN presenting this brief historical perspective, it is not my purpose to address myself to the geophysicists, to most of whom the story is already well known. My objective is to draw the attention of those who hold the belief that geophysics is something new, typically twentieth century, to the fact that fundamentally, whether it was known by the name of geo-physics or not, the science is an ancient and an honorable one. It began many centuries ago, and our modern civilization and its commerce owe a great debt to Its founders, who today are likely to be overlooked and their names forgotten. The word "geophysics" means the physics of the earth, and is descriptive of a science that in many ways bears the same relationship to geology that astrophysics does to astronomy. When dealing with dis-tant stars or deeply buried rocks, the experimenter cannot reach them to obtain samples, which can be taken to his laboratory for study. He therefore exhibits the resourcefulness of Mahomet in the mountain episode, and makes the terrestrial globe or the cosmic universe his labora-tory, studying the effects of distant bodies on certain "fields of force" which come to him across interstellar space, or through the rocks that make our earth. The application of these techniques of the physics laboratory to the study of the stars is the science of astrophysics, and to the investigation of the earth is geophysics. Yet the origin of the most valuable contribution to the world's trade and commerce ever made by geophysics remains lost in deep obscurity. Unknown even is the country wherein lived the unsung genius who invented the first geophysical instrument, the mariner's compass! Worse yet, it is not certain whether this invaluable guide of man had its begin-nings in Europe or in Asia. A Chinese legend tells of the Emperor Hwang-ti, who attacked his enemy Tchi-yeou on the plains of Tchou-lou in the year 2634 B.C., whereupon the latter magically raised such a fog that the Emperor could not pursue the retreating troops. Not to be outdone, the mighty ruler constructed a chariot that indicated the cardi-

Jan 1, 1938

W. C. MATTESON (communication to the Secretary*).-The criticism and question raised by Arthur Knapp regarding the standardization of nomenclature is most important. Faulty rock classification-is generally the result of carelessness or ignorance on the part of the driller. Two remedies might be suggested. In a field where several large companies are operating on an extensive scale, a geologist from each concern might be assigned to superintend the gathering of well-log data and the classification of samples. The geologists from the several operating companies might then combine their data, which would doubtless give valuable information to all interested parties. At present, coordination is not a big factor, unfortunately, but the time will come when conservation will demand such systematic coordination on the part of competing companies. The second remedy lies in instructing and educating the driller to a thorough understanding of the importance of an accurate log and correct classification of the various formations. The writer does not agree with the statement that "90 per cent. of the logs as taken today are absolutely worthless to any one but the one who has taken the log." While mistakes in nomenclature often occur, the driller is generally able to classify the important water-, oil-, and gas-bearing formations with a fair degree of accuracy. Such information is often sufficient to permit accurate correlation and also constitutes valuable data for projection purposes. It must be borne in mind that to attempt to use well-log data in a strict scientific sense of accuracy is impracticable and impossible. A broad interpretation and a comprehensive knowledge of the practical limits of such' information are essential in applying it successfully. Even experienced geologists do not always agree on rock classification. The question as to what constitutes correct nomenclature should receive the earnest and immediate attention of geologists, operators, and producers. Although standard textbooks on geology give correct definitions and descriptions of the general rock species, such textbooks fail to develop the subject in sufficient detail for the work under consideration. A committee composed of appointed members from the American Institute of Mining Engineers, the Geological Society of America, and the

Jan 6, 1917

By Sherwin F. Kelly

In presenting this brief historical perspective, it is not my purpose to address myself to the geophysicists, to most of whom the story is already well known. My objective is to draw the attention of those who hold the belief that geophysics is something new, typically twentieth century, to the fact that fundamentally, whether it was known by the name of geophysics or not, the science is an ancient and an honorable one. It began many centuries ago, and our modern civilization and its commerce owe a great debt to its founders, who today are likely to be overlooked and their names forgotten. The word "geophysics" means the physics of the earth, and is descriptive of a science that in many ways bears the same relationship to geology that astrophysics does to astronomy. When dealing with distant stars or deeply buried rocks, the experimenter cannot reach them to obtain samples, which can be taken to his laboratory for study. He therefore exhibits the resourcefulness of Mahomet in the mountain episode, and makes the terrestrial globe or the cosmic universe his laboratory, studying the effects of distant bodies on certain "fields of force" which come to him across interstellar space, or through the rocks that make our earth. The application of these- techniques of the physics laboratory to the study of the stars is the science of astrophysics, and to the investigation of the earth is geophysics. Yet the origin of the most valuable contribution to the world's trade and commerce ever made by geophysics remains lost in deep obscurity. Unknown even is the country wherein lived the unsung genius who invented the first geophysical instrument, the mariner's compass! Worse yet, it is not certain whether this invaluable guide of man had its beginnings in Europe or in Asia. A Chinese legend tells of the Emperor Hwang-ti, who attacked his enemy Tchi-yeou on the plains of Tehou-lou in the year 2634 B.C., whereupon the latter magically raised such a fog that the Emperor could not pursue the retreating troops. Not to be outdone, the mighty ruler constructed a chariot that indicated the cardi-

Jan 1, 1940

By Sherwin F. Kelly

In presenting this brief historical perspective, it is not my purpose to address myself to the geophysicists, to most of whom the story is already well known. My objective is to draw the attention of those who hold the belief that geophysics is something new, typically twentieth century, to the fact that fundamentally, whether it was known by the name of geophysics or not, the science is an ancient and an honorable one. It began many centuries ago, and our modern civilization and its commerce owe a great debt to its founders, who today are likely to be overlooked and their names forgotten. The word "geophysics" means the physics of the earth, and is descriptive of a science that in many ways bears the same relationship to geology that astrophysics does to astronomy. When dealing with distant stars or deeply buried rocks, the experimenter cannot reach them to obtain samples, which can be taken to his laboratory for study. He therefore exhibits the resourcefulness of Mahomet in the mountain episode, and makes the terrestrial globe or the cosmic universe his laboratory, studying the effects of distant bodies on certain "fields of force" which come to him across interstellar space, or through the rocks that make our earth. The application of these- techniques of the physics laboratory to the study of the stars is the science of astrophysics, and to the investigation of the earth is geophysics. Yet the origin of the most valuable contribution to the world's trade and commerce ever made by geophysics remains lost in deep obscurity. Unknown even is the country wherein lived the unsung genius who invented the first geophysical instrument, the mariner's compass! Worse yet, it is not certain whether this invaluable guide of man had its beginnings in Europe or in Asia. A Chinese legend tells of the Emperor Hwang-ti, who attacked his enemy Tchi-yeou on the plains of Tehou-lou in the year 2634 B.C., whereupon the latter magically raised such a fog that the Emperor could not pursue the retreating troops. Not to be outdone, the mighty ruler constructed a chariot that indicated the cardi-

Jan 1, 1940

By Raymond Mancha

TO determine the optimum inside dimension of an airshaft, it is necessary to strike the proper balance between the cost of power for air friction and turbulence losses within the airshaft, on the one hand, and the cost of sinking the airshaft, on the other. An airshaft larger than necessary is extravagant because the increased amortization rate exceeds the reduction in power cost. Conversely, an airshaft smaller than is needed wastes more power than can be justified by the corresponding reduction in amortization rate. The airshaft power is a function of the air volume Q cu. ft. per min. and the air- pressure drop p in. water gauge across the airshaft The airshaft pressure drop is calculated by the formula: [ ] wherein R is the air-friction coefficient for the portion of the airshaft 1 ft. deep, 0 ft. in perimeter and A sq. ft. in area, when passing an air volume of Q cu. ft. per minute. The airpower w kw. dissipated within the airshaft is computed by the formula: [ ] With a combined over-all unit efficiency of the fan and drive of E per cent, the air- shaft power requirements become [ ] There are 8760 hours per year, so with energy at I cent per kilowatt-hour the annual cost per kilowatt for continuous operation is $87.60; therefore, with energy at C$ per kw-hr. the annual airshaft power cost MI dollars per year becomes: [ ] which, expressed by the component parts, becomes : [] The amortization rate a dollars per year per dollar invested includes both depreciation and interest on the investment. These in turn involve the expected useful life of the airshaft and available monetary interest rate. For the purpose of this discussion the cost of airshaft sinking is assumed to comprise a fixed move-in charge Y dollars, which covers the cost of transporting, erecting and removing the shaft-sinking equipment and is independent of the air- shaft size. Also, it is assumed that the cost of shaft lining, if any, is fixed at $X per cu. yd. of lining material and that excava-

Jan 1, 1946

By Geoffrey Purcell

For anyone contemplating flotation research with only a very limited amount of mineral available for testing, the choice of suitable experimental equipment is by no means obvious. Hallimond's original and delightfully simple cell1 has been modified by subsequent investigators2to give quantitative and reproducible results on small samples. However, the modifications have necessarily compromised its simplicity, and the services of a skilled glass blower are required to duplicate the cell. Vacuum flotation tests3 at best qualitative and may, under certain conditions4, be quite impracticable. A hundred years ago, Thoreau observed that "our life is frittered away by detail," and his advice was to "simplify, simplify," The success of the simple cell described below, which was developed by the author and differs somewhat from Hallimond's original, suggests that Thoreau's advice still has merit a century later. CELL CONSTRUCTION The cell [Fig. 1 (a) and 1 (b)] consists essentially of a 25-ml pipet from which has been cut the con- stricted top. The length cut off is not critical since this merely determines the final volume of the cell. Cell volume may be varied in this way from 20 to 50 cc. A pyrex extension tube, equal in diameter and approximately half the length of the cut pipet, is attached to the top of the pipet by means of 2 ½ in. of close-fitting tygon tubing. When assembled, the two pyrex tubes should be spaced about ½ in. apart. Another length of tygon tubing is added to the extension piece for sealing purposes. A ¾ -in. disc of porous material (teflon cloth is ideal), secured in place over the pipet tip with another piece of shaped tygon tubing, completes the cell assembly. Tygon tubing may be shaped by pushing it over the pipet tip or some similar form and heating carefully over a low flame. For flotation [Fig. 1 (c) 1, the pyrex extension tube is rotated approximately 70º from the vertical and held in position by a wire hook and eye. Floated material, after reaching the free surface, falls and rests on this inclined plane. The barrier formed by the bent tygon tubing ensures that floated material does not slide back and return to the vertical portion of the cell.

Jan 11, 1965

By M. C. Fuerstenau, D. W. Fuerstenau

Studies of the collection of alkali and ammonium halides utilizing vacuum flotation techniques and contact angle measurements show that ionic size controls the flotation of techniquesthese halides with amine salts measurementsas collector. Contact angles of air bubbles on sylvite in saturated brines were withaminemeasured salts asascollector.a function of such variables as collector addition, length of collector chain, and pH of the brine. No contact occurs between halite and an air bubble in brines containing dodecylammonium acetate as collector. LONG-CHAINED aliphatic amine salts have been used for the separation of sylvite (KCl) from halite (NaCl) by flotation.1,2 It is puzzling how these two minerals, which are so similar chemically and crystallographically, can be separated by this method. Gaudin" has postulated that the difference in floatability of halite and sylvite with salts of primary amines depends on ionic size: In the case of amine flotation, the cation would attach itself to the chloride. I have a speculation there, which I cannot prove, that the ammonium group, that is the —NH3 group in the amine, floats potassium chloride because the dimensions of this grour, as it has been measured in other compounds is almost identically the dimensions of the potassium ion, quite different from the sodium ion, and so it fits where potassium had been, in place of it and not attached to it. Apparently, because an aminium ion (RNH3+) is much larger than a sodium ion, it cannot fit into the lattice of halite. Taggart also has speculated that ionic size may control the floatability of sylvite.4 The object of this experimental investigation has been to test this hypothesis and to study what controls the adsorption of cationic collectors at the surface of sylvite. Since collection is to be approached from the viewpoint of ionic size, the ionic radii that are of interest in this work are presented in Table I. The values of the ionic radii of the ions listed in Table I, except NH4+, are those given by Pauling." Several different values for the radius of the ammonium ion have been given, but that of Goldschmidt6 seems to be preferred. The radius of the charged head of a dodecylammonium ion is assumed to be the same as that for the ammonium ion. Little experimental work has been reported in the technical literature concerning the separation of sylvite from halite by flotation. Guyer and Perren studied the separation by flotation of 50 pct binary mixtures of NaCl, KC1, NH,Cl, NaNO3, KNO3, K2SO4, and Na,SO, using either oleic acid or a sodium sul-fonate as collector.' It is possible to measure floatability under actual flotation conditions where all three phases, air- water-mineral, are present by vacuum flotation tests and contact angle measurements.9 Both of these techniques were used in the experimental approach in this paper. Experimental Method and Materials The vacuum flotation tests were run with glass-stoppered pyrex graduated cylinders. Twenty-five ml graduates were used to test the floatability of all salts studied except rubidium and cesium salts. For each test distilled water containing the desired collector concentration was saturated with the salt to be floated. Sufficient salt (—48 mesh) was added to leave about 2 ml of solids in the bottom of the graduate. After the graduate had been agitated several minutes to saturate the solution with air, a vacuum was applied. If the salt were floatable in the collector solution, the gas bubbles attached themselves to the particles, and the particles floated to the surface. In determining the floatability of the expensive Rb and Cs halides, the experiments were run in 10 ml graduates with about 11/2 ml of collector solution initially. Contact angles were measured in the usual manner except that the solutions had to be previously saturated with the mineral to avoid dissolution of the crystal. Solutions for studying contact angles were made by adding the desired amount of collector to a saturated brine, giving the collector concentration in molarity. The mixture was agitated until dissolution of the collector was complete, with the exception of those concentrations greater than about millimolar. At these high concentrations complete dissolution of the collector was impossible. The face of the mineral to be tested was a freshly cleaved crystal of halite or sylvite. The mineral was placed in the brine and conditioned with collector for at least 15 min, which was found to be long enough to obtain a maximum value for the contact angle. The temperature remained constant during each experiment. The experiments were run at 24°C ±2°C. For contact angle measurements, a crystal of halite from Carlsbad, N. M., was used. Several samples of sylvite were used in this work: a crystal of sylvite from Stassfurt, Germany; a crystal from Carlsbad, N. M.; and a crystal of chemically pure potassium chloride. Saturated brines were made from reagent grade chemicals and distilled water.

Jan 1, 1957

By Y. C. Liu, G. A. Alers

Using X-ray pole-figure information and the single-crystal elastic constants, the angular variation of an elastic modulus in a polycrystal can be calculated and compared to measured clalues. This procedure has been used in the past to provide supporting ecidence for a particular choice of ideal orientations in the description o the X-ray pole figure. Since it is well-known that the absolute value oj an elastic modlus oj a poly crystal cannot be acczrralely calculated from the single-crystal elastic constants, there exists a serious question about the reliability oj this modulus method in the study of textures. This paper deriz-es sez3eral simple fornzulae for the ntzgular lariatiion of Young's modulus in the plane o a rolled sheet sing the same ssuinptions which lead to the lack oj detinztion of the absolute c'alre OJ the elastic ,nodulus. The vesults show that, although the absolute isallre oj Young's modulus depends strongly on the assumptions made, the shape of the modulus vs angle curve is not very sensitive to the assumptions and thus can be used reliably in texture studies. Exatzples oj' using this criteriotz are illustrated in the text. NeARLY all poly crystalline materials have some preferred orientation in the arrangement of their grains and hence exhibit anisotropy in their properties. This preferred orientation is usually measured and studied by X-rays which yield detailed information on the statistical distribution of grain orientations in the form of pole figures. The usefulness of these pole figures in theories of texture formation and in predictions of properties has come to depend almost entirely on the characterization of the pole figure by one or more ideal orientations. Unfortunately, this characterization is not unique and different authors often present different ideal orientations to characterize a given pole figure. In order to distinguish between these different choices of ideal orientations, it is necessary to go beyond X-rays and consider other physical properties which reflect the texture' simply because any choice of ideal orientations must predict correctly the observed anisotropy in all physical properties. The most common example of this procedure has made use of the angular variation of Young's modulus with respect to the rolling direction in the plane of a rolled sheet.3 4 Here the anisotropy can be measured easily and it can also be calculated from the single-crystal elastic constants and the chosen ideal orientation. Unfortunately the methods used to calculate this anisotropy were chosen for their simplicity rather than for their mathematical rigor so that there exists a serious question as to the validity of conclusions reached by this modulus method. It is well-known5 that the absolute value of the Young's modulus of a polycrystalline aggregate cannot be calculated very accurately because different mathematical averages over the grains yield different results. It is one purpose of this paper to examine the effect of different averaging procedures on the calculated anisotropy of Young's modulus in the rolling plane of rolled sheets in order to see if this property can be used reliably in texture studies. This particular modulus and type of material were chosen because the modulus is easily measured and rolled sheet is technologically important. The results show that, although different averages yield different absolute values for Young's modulus, the shape of the modulus vs angle curve is not very sensitive to the averaging procedure and thus can be used as a criterion to check the various ideal orientations used to characterize the X-ray pole figure. Examples of this checking procedure are given in the final section. Another purpose of this paper is to examine the possibility of using the anisotropy of Young's modulus as an indicator of texture without reference to pole figures or ideal orientations. Such a use would require that different textures yield quite different shapes for the modulus vs angle curve so that the distinction between textures would be quite clear. The experimental results presented in the final section indicate that there is easily enough variation in shapes to allow modulus measurements to be useful texture indicators, par-

Jan 1, 1967